Specifications:
* SoC: Qualcomm IPQ6018/AP-CP03-C1 (64-bit Quad-core Arm Cortex-A53 @ 1.2 GHz)
* RAM: 2x Zentel A3T4GF40BBF-HP (1 GiB DDR3-1866 (13-13-13))
* Serial Port: 1v8 TTL 115200n8
* Wi-Fi: Qualcomm QCN5022 (802.11ax/b/g/n)
* Wi-Fi: Qualcomm QCN5052 (802.11ac/ax/n)
* Ethernet: RTL8211FS (10/100/1000BASE-T)
* Flash: GigaDevice PSR1GA30DT (128 MiB)
* LEDs: 1x Blue Status (GPIO 35 Active High)
* Buttons: 1x Reset (GPIO 9 Active Low)
* FCCID: 2AXJ4EAP620HDV3
* UART: 4-pin unpopulated header by the J1 footprint
Installation Instructions (Serial+TFTP):
1. Locate the J1 footprint which contains 4 unpopulated pins
where starting from the arrow, the pins are TX, RX, VCC and GND
respectively.
2. Connect a 1v8 TTL port to the 4 pins. Ensure RX and TX are crossed
over.
3. Copy openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-initramfs-uImage.itb
to your TFTP server.
4. Power up the AP and hold Ctrl+B in the serial console (115200n8) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
IPQ6018# setenv serverip <TFTP server addr>
IPQ6018# setenv ipaddr <addr of the AP>
IPQ6018# tftpboot 0x44000000 openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-initramfs-uImage.itb
IPQ6018# bootm 0x44000000
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp -O openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Installation Instructions (Web UI method):
1. Set up the device using the vendor's web UI. Navigate to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
2. Connect to the machine via SSH:
$ ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
3. Disable signature verification:
$ cliclientd stopcs
4. Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
5. Go to System -> Firmware Update.
Under "New Firmware File", click "Browse" and select the image.
Select "Update" and confirm by clicking "OK".
6. If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWrt.
Device support followed from EAP620HD v2 and eap6xx-outdoor for DTS.
Links: openwrt/openwrt#18227
Signed-off-by: John Christoforidis <github@yanny.dev>
Link: https://github.com/openwrt/openwrt/pull/21467
Signed-off-by: Robert Marko <robimarko@gmail.com>
netgear,wax610y|\
tplink,eap610-outdoor|\
tplink,eap623od-hd-v1|\
+tplink,eap620-hd-v3|\
tplink,eap625-outdoor-hd-v1)
ubootenv_add_mtd "0:appsblenv" "0x0" "0x40000" "0x20000"
;;
tplink_deco-x80-5g \
tplink_eap610-outdoor \
tplink_eap620hd-v1 \
+ tplink_eap620-hd-v3 \
tplink_eap623-outdoor-hd-v1 \
tplink_eap625-outdoor-hd-v1 \
tplink_eap660hd-v1 \
$(eval $(call generate-ipq-wifi-package,tplink_deco-x80-5g,TP-Link Deco X80-5G))
$(eval $(call generate-ipq-wifi-package,tplink_eap610-outdoor,TPLink EAP610-Outdoor))
$(eval $(call generate-ipq-wifi-package,tplink_eap620hd-v1,TP-Link EAP620 HD v1))
+$(eval $(call generate-ipq-wifi-package,tplink_eap620-hd-v3,TP-Link EAP620 HD v3))
$(eval $(call generate-ipq-wifi-package,tplink_eap623-outdoor-hd-v1,TP-Link EAP623-Outdoor HD v1))
$(eval $(call generate-ipq-wifi-package,tplink_eap625-outdoor-hd-v1,TP-Link EAP625-Outdoor HD v1))
$(eval $(call generate-ipq-wifi-package,tplink_eap660hd-v1,TP-Link EAP660 HD v1))
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "ipq6018-tplink-eap6xx-outdoor.dtsi"
+
+/ {
+ model = "TP-Link EAP620HD v3";
+ compatible = "tplink,eap620-hd-v3", "qcom,ipq6018";
+
+ /* Delete EAP6xx outdoor leds node to redefine it. */
+ /delete-node/ leds;
+
+ aliases {
+ led-boot = &led_status_blue;
+ led-failsafe = &led_status_blue;
+ led-running = &led_status_blue;
+ led-upgrade = &led_status_blue;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status_blue: status-blue {
+ function = LED_FUNCTION_STATUS;
+ gpios = <&tlmm 35 GPIO_ACTIVE_HIGH>;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+ };
+};
+
+&mdio {
+ rtl8211f_4: ethernet-phy@4 {
+ reg = <4>;
+ compatible = "ethernet-phy-ieee802.3-c22";
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <20 1>;
+};
+
+&switch {
+ switch_mac_mode1 = <MAC_MODE_SGMII_PLUS>;
+};
+
+&wifi {
+ qcom,ath11k-calibration-variant = "TP-Link-EAP620-HD-v3";
+ status = "okay";
+};
endef
TARGET_DEVICES += tplink_eap625-outdoor-hd-v1
+define Device/tplink_eap620-hd-v3
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_VENDOR := TP-Link
+ DEVICE_MODEL := EAP620 HD v3
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ SOC := ipq6018
+ DEVICE_PACKAGES := ipq-wifi-tplink_eap620-hd-v3
+ IMAGES += web-ui-factory.bin
+ IMAGE/web-ui-factory.bin := append-ubi | tplink-image-2022
+ TPLINK_SUPPORT_STRING := SupportList:\r\n \
+ EAP620 HD(TP-Link|UN|AX1800-D):3.0\r\n \
+ EAP620 HD(TP-Link|CA|AX1800-D):3.0\r\n \
+ EAP620 HD(TP-Link|JP|AX1800-D):3.0\r\n \
+ EAP620 HD(TP-Link|EG|AX1800-D):3.0\r\n
+
+endef
+TARGET_DEVICES += tplink_eap620-hd-v3
+
define Device/yuncore_fap650
$(call Device/FitImage)
$(call Device/UbiFit)
netgear,wax610y|\
tplink,eap610-outdoor|\
tplink,eap623od-hd-v1|\
+ tplink,eap620-hd-v3|\
tplink,eap625-outdoor-hd-v1)
ucidef_set_interface_lan "lan" "dhcp"
;;
label_mac=$lan_mac
;;
tplink,eap610-outdoor|\
+ tplink,eap620-hd-v3|\
tplink,eap623od-hd-v1|\
tplink,eap625-outdoor-hd-v1)
label_mac=$(get_mac_binary /tmp/factory_data/default-mac 0)
ath11k_patch_mac $(macaddr_add $label_mac 1) 0
ath11k_set_macflag
;;
+ tplink,eap620-hd-v3)
+ caldata_from_file "/tmp/factory_data/radio" 0 0x20000
+ label_mac=$(get_mac_binary /tmp/factory_data/default-mac 0)
+ ath11k_patch_mac $label_mac 1
+ ath11k_patch_mac $(macaddr_add $label_mac 1) 0
+ ath11k_set_macflag
+ ;;
yuncore,fap650)
caldata_extract "0:art" 0x1000 0x20000
;;
case $(board_name) in
tplink,eap610-outdoor|\
+ tplink,eap620-hd-v3|\
tplink,eap623od-hd-v1|\
tplink,eap625-outdoor-hd-v1)
mtd_path=$(find_mtd_chardev "factory_data")
nand_do_upgrade "$1"
;;
tplink,eap610-outdoor|\
+ tplink,eap620-hd-v3|\
tplink,eap623od-hd-v1|\
tplink,eap625-outdoor-hd-v1)
tplink_do_upgrade "$1"
projects / thirdparty / openwrt.git / commitdiff
