--- /dev/null
+UpgradeImages="zImage rd.gz hddapp.tgz"
+productName="Verbatim Network Attached Storage"
+hardwareName="Verbatim S08V1901"
+productVendor="Verbatim Corproation"
+VendorID="verbatim"
+ProductID="v1901"
+UpgradeVersion="263"
+ExtraVersion="n"
+manufacturerURL="http://www.verbatim.com"
+Description="Verbatim VerbatimNAS"
+hostname="verbatimnas"
+softwareVersion="2.0.0"
+TSS="enabled"
+DIRECT_MODE="disabled"
+Raid_Support="raid0_raid1_raid5_linear"
+RaidTestDiskSize="0"
+Raid_Show_Disk="6"
+DEFAULT_LAN_IPADDR="192.168.1.1"
+DEFAULT_LAN_NETMASK="255.255.255.0"
+DEFAULT_LAN_BOOTPROTO="dhcp"
+DEFAULT_WAN_BOOTPROTO="none"
+DEFAULT_WAN_ENABLED="no"
+DEFAULT_WLAN_DEVICENAME="ra0"
+DEFAULT_LAN_DEVICENAME="eth0"
+DEFAULT_HW_LAN_DEVICENAME="eth0"
+DEFAULT_WAN_DEVICENAME="eth1"
+DEFAULT_HW_WAN_DEVICENAME="eth1"
+SUPPORT_FILESYSTEM="ext2_ext3_fat32"
+SUPPORT_ENCRYPT_FILESYSTEM="ext2"
+DEFAULT_DHCP_ENABLED="0"
+SUPPORT_CODEPAGE="CP437_CP950_CP936_CP1145_CP1250_CP1252_CP932_CP949"
+DEFAULT_SERVER_CODEPAGE="CP437"
+FACTORY_RESET_ADMIN="0"
+DEFAULT_TIME_ZONE="Eastern"
--- /dev/null
+From 46267aeb78cc7aba845da4c17acff1d46b694647 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linusw@kernel.org>
+Date: Wed, 14 Jan 2026 09:29:48 +0100
+Subject: [PATCH 1/2] ARM: dts: Add a Verbatim Gigabit NAS DTS
+
+This adds a device tree for the Verbatim S08V1901-D1 NAS
+which also has the product names "Gigabit Network Hard Drive"
+"Gigabit NAS" and maybe other names.
+
+Signed-off-by: Linus Walleij <linusw@kernel.org>
+---
+ arch/arm/boot/dts/gemini/Makefile | 1 +
+ .../gemini/gemini-verbatim-s08v1901-d1.dts | 225 ++++++++++++++++++
+ 2 files changed, 226 insertions(+)
+ create mode 100644 arch/arm/boot/dts/gemini/gemini-verbatim-s08v1901-d1.dts
+
+--- a/arch/arm/boot/dts/gemini/Makefile
++++ b/arch/arm/boot/dts/gemini/Makefile
+@@ -8,5 +8,6 @@ dtb-$(CONFIG_ARCH_GEMINI) += \
+ gemini-sl93512r.dtb \
+ gemini-sq201.dtb \
+ gemini-ssi1328.dtb \
++ gemini-verbatim-s08v1901-d1.dtb \
+ gemini-wbd111.dtb \
+ gemini-wbd222.dtb
+--- /dev/null
++++ b/arch/arm/boot/dts/gemini/gemini-verbatim-s08v1901-d1.dts
+@@ -0,0 +1,225 @@
++// SPDX-License-Identifier: GPL-2.0
++/*
++ * Device Tree file for the Verbatim S08V1901-D1
++ * on product packaging called "Verbatim Gigabit Ethernet Hard Drive"
++ */
++
++/dts-v1/;
++
++#include "gemini.dtsi"
++#include <dt-bindings/leds/common.h>
++#include <dt-bindings/input/input.h>
++
++/ {
++ model = "Verbatim Gigabit Ethernet Hard Drive S08V1901-D1";
++ compatible = "verbatim,s08v1901-d1", "cortina,gemini";
++ #address-cells = <1>;
++ #size-cells = <1>;
++
++ memory@0 {
++ /* 64MB SDRAM in 2 x Hynix HY5DU561622ETP-D43 */
++ device_type = "memory";
++ reg = <0x00000000 0x4000000>;
++ };
++
++ chosen {
++ bootargs = "console=ttyS0,19200n8 root=/dev/sda1 rw rootwait";
++ stdout-path = &uart0;
++ };
++
++ gpio_keys {
++ compatible = "gpio-keys";
++
++ button-reset {
++ debounce-interval = <50>;
++ wakeup-source;
++ linux,code = <KEY_RESTART>;
++ label = "reset";
++ gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
++ };
++ };
++
++ leds {
++ compatible = "gpio-leds";
++ led-green-harddisk {
++ function = LED_FUNCTION_DISK_ACTIVITY;
++ color = <LED_COLOR_ID_GREEN>;
++ gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
++ default-state = "off";
++ linux,default-trigger = "disk-activity";
++ };
++ };
++
++ /*
++ * Fan control candidates: gpio0 10, gpio1 28
++ */
++
++ mdio0: mdio {
++ compatible = "virtual,mdio-gpio";
++ /* Uses MDC and MDIO */
++ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
++ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ /* This is a Realtek RTL8211CL ethernet PHY */
++ phy0: ethernet-phy@1 {
++ reg = <1>;
++ };
++ };
++
++ /*
++ * I haven't found a way to control the fan, it appears to be
++ * always on.
++ */
++ thermal-zones {
++ chassis-thermal {
++ /* Poll every 20 seconds */
++ polling-delay = <20000>;
++ /* Poll every 2nd second when cooling */
++ polling-delay-passive = <2000>;
++ /* Use the thermal sensor in the hard drive */
++ thermal-sensors = <&drive0>;
++
++ /* Tripping points from the fan.script in the rootfs */
++ trips {
++ alert: chassis-alert {
++ /* At 43 degrees turn on the fan */
++ temperature = <43000>;
++ hysteresis = <3000>;
++ type = "active";
++ };
++ crit: chassis-crit {
++ /* Just shut down at 60 degrees */
++ temperature = <60000>;
++ hysteresis = <2000>;
++ type = "critical";
++ };
++ };
++ };
++ };
++
++ soc {
++ flash@30000000 {
++ /*
++ * This is a Spansion S29GL128P11TFI01 852FB245 A
++ * 128Mbit (16MB) Flash memory.
++ */
++ status = "okay";
++ reg = <0x30000000 0x01000000>;
++
++ partitions {
++ compatible = "redboot-fis";
++ /* Eraseblock at 0xfe0000 */
++ fis-index-block = <0x7f>;
++ };
++ };
++
++ syscon: syscon@40000000 {
++ pinctrl {
++ /*
++ * gpio0agrp cover line 0-4 as line 1 is used for the LED
++ * gpio0hgrp cover line 21, 22 used by MDIO for Marvell PHY
++ */
++ gpio0_default_pins: pinctrl-gpio0 {
++ mux {
++ function = "gpio0";
++ groups = "gpio0agrp", "gpio0hgrp";
++ };
++ };
++ gpio1_default_pins: pinctrl-gpio1 {
++ /*
++ * Free up the TVC pins at GPIO1 offset 28,29,30,31
++ * line 31 is used for reset key
++ */
++ mux {
++ function = "gpio1";
++ groups = "gpio1dgrp";
++ };
++ };
++ pinctrl-gmii {
++ mux {
++ function = "gmii";
++ groups = "gmii_gmac0_grp";
++ };
++ /* TODO: investigate vendor registers on boot */
++ conf0 {
++ pins = "V8 GMAC0 RXDV";
++ skew-delay = <0>;
++ };
++ conf1 {
++ pins = "Y7 GMAC0 RXC";
++ skew-delay = <15>;
++ };
++ conf2 {
++ pins = "T8 GMAC0 TXEN";
++ skew-delay = <7>;
++ };
++ conf3 {
++ pins = "U8 GMAC0 TXC";
++ skew-delay = <10>;
++ };
++ conf4 {
++ /* The data lines all have default skew */
++ pins = "W8 GMAC0 RXD0", "V9 GMAC0 RXD1",
++ "Y8 GMAC0 RXD2", "U9 GMAC0 RXD3",
++ "T7 GMAC0 TXD0", "U6 GMAC0 TXD1",
++ "V7 GMAC0 TXD2", "U7 GMAC0 TXD3";
++ skew-delay = <7>;
++ };
++ };
++ };
++ };
++
++ /* Both interfaces brought out on SATA connectors */
++ sata: sata@46000000 {
++ cortina,gemini-ata-muxmode = <0>;
++ cortina,gemini-enable-sata-bridge;
++ status = "okay";
++ };
++
++ gpio0: gpio@4d000000 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&gpio0_default_pins>;
++ };
++
++ gpio1: gpio@4e000000 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&gpio1_default_pins>;
++ };
++
++ ethernet@60000000 {
++ status = "okay";
++
++ ethernet-port@0 {
++ phy-mode = "rgmii";
++ phy-handle = <&phy0>;
++ };
++ };
++
++ ide@63000000 {
++ status = "okay";
++ /*
++ * This drive may have a temperature sensor with a
++ * thermal zone we can use for thermal control of the
++ * chassis temperature using the fan.
++ */
++ drive0: ide-port@0 {
++ reg = <0>;
++ #thermal-sensor-cells = <0>;
++ };
++ };
++
++ ide@63400000 {
++ status = "okay";
++ };
++
++ usb@68000000 {
++ status = "okay";
++ };
++
++ usb@69000000 {
++ status = "okay";
++ };
++ };
++};
--- /dev/null
+From 590d33c31529aae924fc38e356e93beca684e3be Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linusw@kernel.org>
+Date: Sun, 1 Feb 2026 23:10:25 +0100
+Subject: [PATCH 2/2] gemini: augment Verbatim DTS with botched partitions
+
+Same botched partitions as the Raidsonic IB-4220-B.
+
+Signed-off-by: Linus Walleij <linusw@kernel.org>
+---
+ .../gemini/gemini-verbatim-s08v1901-d1.dts | 39 +++++++++++++++++--
+ 1 file changed, 35 insertions(+), 4 deletions(-)
+
+--- a/arch/arm/boot/dts/gemini/gemini-verbatim-s08v1901-d1.dts
++++ b/arch/arm/boot/dts/gemini/gemini-verbatim-s08v1901-d1.dts
+@@ -23,7 +23,7 @@
+ };
+
+ chosen {
+- bootargs = "console=ttyS0,19200n8 root=/dev/sda1 rw rootwait";
++ bootargs = "console=ttyS0,19200n8";
+ stdout-path = &uart0;
+ };
+
+@@ -108,10 +108,41 @@
+ status = "okay";
+ reg = <0x30000000 0x01000000>;
+
++ /*
++ * Override the RedBoot partition table with fixed partitions
++ * in order to create a coherent "firmware" partition so that
++ * we can have optimal flash usage with OpenWrt in a big
++ * MTD-splitted "firmware" partition.
++ */
+ partitions {
+- compatible = "redboot-fis";
+- /* Eraseblock at 0xfe0000 */
+- fis-index-block = <0x7f>;
++ compatible = "fixed-partitions";
++ #address-cells = <1>;
++ #size-cells = <1>;
++ partition@0 {
++ label = "BOOT";
++ reg = <0x00000000 0x00020000>;
++ read-only;
++ };
++ partition@1 {
++ compatible = "openwrt,executable-prolog";
++ label = "firmware";
++ reg = <0x00020000 0x00f00000>;
++ };
++ partition@2 {
++ label = "VCTL";
++ reg = <0x00f20000 0x00020000>;
++ read-only;
++ };
++ partition@3 {
++ label = "CurConf";
++ reg = <0x00f40000 0x000a0000>;
++ read-only;
++ };
++ partition@4 {
++ label = "FIS directory";
++ reg = <0x00fe0000 0x00020000>;
++ read-only;
++ };
+ };
+ };
+
projects / thirdparty / openwrt.git / commitdiff
