This commit adds support for Teralink TL3020 256mb wireless router.
Specification
-------------
- SoC : MediaTek MT7981B dual-core ARM Cortex-A53
- RAM : DDR3 256 MiB (ESMT M15T2G16128A, DDR3-1866)
- Flash : SPI-NAND 256 MiB (Winbond W25M02GV)
- WLAN : MediaTek MT7976 2.4/5 GHz Wi-Fi 6
- Ethernet : MediaTek MT7531 switch, 1x WAN + 3x LAN 10/100/1000 Mbps
(2.5GbE uplink via gmac0)
- USB : 1x USB 2.0 Type-A (power enable on GPIO 14)
- Buttons : WPS, Reset
- LEDs : 7x blue, 1x red
- UART : 4-pin header on PCB
- assignment : 3.3V, GND, TX, RX
- settings : 115200n8
- Power : 12 VDC, 1.5 A (barrel jack)
MAC addresses
-------------
EEPROM MAC is same for all the devices, but there is a `config2` partition
with unique MAC addresses:
| Interface | MAC source |
|-----------|--------------------------------------------|
| LAN | config2, offset 0x707 (ASCII, "lanmac") |
| WAN | config2, offset 0x787 (ASCII, "wanmac") |
| WLAN 2.4G | config2, offset 0x68a (ASCII, "wifi2gmac") |
| WLAN 5G | config2, offset 0x60a (ASCII, "wifi5gmac") |
The LAN MAC (gmac0) is the one printed on the device label.
Installation
------------
Factory bootloader is locked to 64mb partition layout, so OpenWrt U-Boot
has to be flashed first. Steps 1, 2 and 4 are run from a shell on the
stock firmware, where the 'bl2' and 'fip' partitions are writable - in
OpenWrt they are read-only, so the procedure cannot be repeated from
OpenWrt. Back up both partitions before overwriting them:
mtd read bl2 /tmp/bl2.bin
mtd read fip /tmp/fip.bin
1. Upload OpenWrt 'bl31-uboot.fip' and 'preloader.bin' images to the /tmp
dir of the router using scp protocol
2. Write fip and bl2 (replace bootloader):
mtd write /tmp/openwrt-mediatek-filogic-teralink_tl3020-256mb-bl31-uboot.fip fip
mtd write /tmp/openwrt-mediatek-filogic-teralink_tl3020-256mb-preloader.bin bl2
3. Place OpenWrt
'openwrt-mediatek-filogic-teralink_tl3020-256mb-initramfs-recovery.itb'
image on the tftp server (IP: 192.168.1.254)
4. Erase 'ubi' partition and reboot the router:
mtd erase ubi
reboot
5. U-Boot automatically boots the OpenWrt recovery image from the tftp
server to the RAM
6. Upload OpenWrt
'openwrt-mediatek-filogic-teralink_tl3020-256mb-squashfs-sysupgrade.itb'
image to the /tmp dir of the router (IP: 192.168.1.1) using scp
protocol
7. Connect to the router using ssh and run:
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
sysupgrade -n openwrt-mediatek-filogic-teralink_tl3020-256mb-squashfs-sysupgrade.itb
Recovery
--------
1. Place OpenWrt
'openwrt-mediatek-filogic-teralink_tl3020-256mb-initramfs-recovery.itb'
image on the tftp server (IP: 192.168.1.254)
2. Press "Reset" button and power on the router. After ~10 sec release
the button.
3. Use OpenWrt initramfs system for recovery
Reverting to stock firmware requires writing the 'bl2' and 'fip' backups
taken above back with 'mtd write', then flashing the stock image; without
those backups there is no way back, because the stock bootloader cannot
be downloaded from the vendor.
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/24518
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
DEPENDS:=+trusted-firmware-a-mt7981-spim-nand-ddr3
endef
+define U-Boot/mt7981_teralink_tl3020-256mb
+ NAME:=Teralink TL3020 256mb
+ BUILD_SUBTARGET:=filogic
+ BUILD_DEVICES:=teralink_tl3020-256mb
+ UBOOT_CONFIG:=mt7981_teralink_tl3020-256mb
+ UBOOT_IMAGE:=u-boot.fip
+ BL2_BOOTDEV:=spim-nand
+ BL2_SOC:=mt7981
+ BL2_DDRTYPE:=ddr3-1866
+ DEPENDS:=+trusted-firmware-a-mt7981-spim-nand-ddr3-1866
+endef
+
define U-Boot/mt7981_wavlink_wl-wnt100x3
NAME:=WAVLINK WL-WNT100X3
BUILD_SUBTARGET:=filogic
mt7981_qihoo_360t7 \
mt7981_qihoo_360t7-ubi \
mt7981_snr_snr-cpe-ax2 \
+ mt7981_teralink_tl3020-256mb \
mt7981_wavlink_wl-wnt100x3 \
mt7981_xiaomi_mi-router-ax3000t \
mt7981_xiaomi_mi-router-wr30u \
--- /dev/null
+From 6a8b2843894f123a11b800ed985b56d4ef771ddb Mon Sep 17 00:00:00 2001
+From: Fil Dunsky <filipp.dunsky@gmail.com>
+Date: Fri, 12 Jun 2026 21:15:27 +0300
+Subject: [PATCH] board: mediatek: add Teralink TL3020 256mb
+
+Add U-Boot support for the Teralink TL3020 256mb (256 MiB SPI-NAND):
+defconfig, device tree and default environment.
+
+Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
+---
+--- /dev/null
++++ b/configs/mt7981_teralink_tl3020-256mb_defconfig
+@@ -0,0 +1,112 @@
++CONFIG_ARM=y
++CONFIG_ARM_SMCCC=y
++CONFIG_SYS_HAS_NONCACHED_MEMORY=y
++CONFIG_POSITION_INDEPENDENT=y
++CONFIG_ARCH_MEDIATEK=y
++CONFIG_TEXT_BASE=0x41e00000
++CONFIG_SYS_MALLOC_F_LEN=0x4000
++CONFIG_NR_DRAM_BANKS=1
++CONFIG_DEFAULT_DEVICE_TREE="mt7981-teralink-tl3020-256mb"
++CONFIG_OF_LIBFDT_OVERLAY=y
++CONFIG_TARGET_MT7981=y
++CONFIG_SYS_LOAD_ADDR=0x46000000
++CONFIG_PRE_CON_BUF_ADDR=0x4007ef00
++CONFIG_DEBUG_UART_BASE=0x11002000
++CONFIG_DEBUG_UART_CLOCK=40000000
++CONFIG_DEBUG_UART=y
++CONFIG_FIT=y
++CONFIG_BOOTDELAY=30
++CONFIG_AUTOBOOT_KEYED=y
++CONFIG_AUTOBOOT_MENU_SHOW=y
++CONFIG_DEFAULT_FDT_FILE="mediatek/mt7981-teralink-tl3020-256mb.dtb"
++CONFIG_LOGLEVEL=7
++CONFIG_PRE_CONSOLE_BUFFER=y
++CONFIG_LOG=y
++# CONFIG_BOARD_INIT is not set
++CONFIG_BOARD_LATE_INIT=y
++CONFIG_HUSH_PARSER=y
++CONFIG_SYS_PROMPT="MT7981> "
++CONFIG_CMD_CPU=y
++CONFIG_CMD_LICENSE=y
++CONFIG_CMD_BOOTMENU=y
++CONFIG_CMD_ASKENV=y
++CONFIG_CMD_ERASEENV=y
++CONFIG_CMD_ENV_FLAGS=y
++CONFIG_CMD_RNG=y
++CONFIG_CMD_STRINGS=y
++CONFIG_CMD_DM=y
++CONFIG_CMD_GPIO=y
++CONFIG_CMD_GPT=y
++CONFIG_CMD_MTD=y
++CONFIG_CMD_PART=y
++CONFIG_CMD_TFTPSRV=y
++CONFIG_CMD_RARP=y
++CONFIG_CMD_CDP=y
++CONFIG_CMD_SNTP=y
++CONFIG_CMD_LINK_LOCAL=y
++CONFIG_CMD_DHCP=y
++CONFIG_CMD_DNS=y
++CONFIG_CMD_PING=y
++CONFIG_CMD_PXE=y
++CONFIG_CMD_CACHE=y
++CONFIG_CMD_PSTORE=y
++CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000
++CONFIG_CMD_UUID=y
++CONFIG_CMD_HASH=y
++CONFIG_CMD_SMC=y
++CONFIG_CMD_UBI=y
++CONFIG_CMD_UBI_RENAME=y
++CONFIG_OF_EMBED=y
++CONFIG_ENV_OVERWRITE=y
++CONFIG_ENV_IS_IN_UBI=y
++CONFIG_ENV_REDUNDANT=y
++CONFIG_ENV_UBI_PART="ubi"
++CONFIG_ENV_UBI_VOLUME="ubootenv"
++CONFIG_ENV_UBI_VOLUME_REDUND="ubootenv2"
++CONFIG_ENV_RELOC_GD_ENV_ADDR=y
++CONFIG_ENV_USE_DEFAULT_ENV_TEXT_FILE=y
++CONFIG_ENV_DEFAULT_ENV_TEXT_FILE="defenvs/teralink_tl3020-256mb_env"
++CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
++CONFIG_VERSION_VARIABLE=y
++CONFIG_NETCONSOLE=y
++CONFIG_USE_IPADDR=y
++CONFIG_IPADDR="192.168.1.1"
++CONFIG_USE_SERVERIP=y
++CONFIG_SERVERIP="192.168.1.254"
++CONFIG_NET_RANDOM_ETHADDR=y
++CONFIG_REGMAP=y
++CONFIG_SYSCON=y
++CONFIG_BUTTON=y
++CONFIG_BUTTON_GPIO=y
++CONFIG_CLK=y
++CONFIG_GPIO_HOG=y
++CONFIG_LED=y
++CONFIG_LED_BLINK=y
++CONFIG_LED_GPIO=y
++# CONFIG_MMC is not set
++CONFIG_MTD=y
++CONFIG_DM_MTD=y
++CONFIG_MTD_SPI_NAND=y
++CONFIG_MTD_UBI_FASTMAP=y
++CONFIG_PHY_FIXED=y
++CONFIG_MEDIATEK_ETH=y
++CONFIG_PHY=y
++CONFIG_PINCTRL=y
++CONFIG_PINCONF=y
++CONFIG_PINCTRL_MT7981=y
++CONFIG_POWER_DOMAIN=y
++CONFIG_MTK_POWER_DOMAIN=y
++CONFIG_DM_REGULATOR=y
++CONFIG_DM_REGULATOR_FIXED=y
++CONFIG_DM_REGULATOR_GPIO=y
++CONFIG_RAM=y
++CONFIG_DM_RNG=y
++CONFIG_RNG_MTK_V2=y
++CONFIG_DM_SERIAL=y
++CONFIG_SERIAL_RX_BUFFER=y
++CONFIG_MTK_SERIAL=y
++CONFIG_SPI=y
++CONFIG_DM_SPI=y
++CONFIG_MTK_SPIM=y
++CONFIG_ZSTD=y
++CONFIG_HEXDUMP=y
+--- /dev/null
++++ b/arch/arm/dts/mt7981-teralink-tl3020-256mb.dts
+@@ -0,0 +1,186 @@
++// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
++/*
++ * Copyright (C) 2026 Fil Dunsky <filipp.dunsky@gmail.com>
++ */
++
++/dts-v1/;
++#include "mt7981.dtsi"
++#include <dt-bindings/gpio/gpio.h>
++#include <dt-bindings/input/linux-event-codes.h>
++
++/ {
++ #address-cells = <1>;
++ #size-cells = <1>;
++ model = "Teralink TL3020 256mb";
++ compatible = "teralink,tl3020-256mb", "mediatek,mt7981";
++
++ chosen {
++ stdout-path = &uart0;
++ tick-timer = &timer0;
++ };
++
++ memory@40000000 {
++ device_type = "memory";
++ reg = <0x40000000 0x10000000>;
++ };
++
++ gpio-keys {
++ compatible = "gpio-keys";
++
++ button-wps {
++ label = "wps";
++ linux,code = <KEY_WPS_BUTTON>;
++ gpios = <&pio 0 GPIO_ACTIVE_LOW>;
++ };
++
++ button-reset {
++ label = "reset";
++ linux,code = <KEY_RESTART>;
++ gpios = <&pio 1 GPIO_ACTIVE_LOW>;
++ };
++ };
++
++ gpio-leds {
++ compatible = "gpio-leds";
++
++ led-wan-red {
++ label = "red:wan";
++ gpios = <&pio 6 GPIO_ACTIVE_HIGH>;
++ };
++
++ led-power {
++ label = "blue:power";
++ gpios = <&pio 7 GPIO_ACTIVE_LOW>;
++ };
++
++ led-lan1 {
++ label = "blue:lan1";
++ gpios = <&pio 9 GPIO_ACTIVE_LOW>;
++ };
++
++ led-lan2 {
++ label = "blue:lan2";
++ gpios = <&pio 10 GPIO_ACTIVE_LOW>;
++ };
++
++ led-lan3 {
++ label = "blue:lan3";
++ gpios = <&pio 11 GPIO_ACTIVE_LOW>;
++ };
++
++ led-wan-blue {
++ label = "blue:wan";
++ gpios = <&pio 12 GPIO_ACTIVE_LOW>;
++ };
++
++ led-wlan2g {
++ label = "blue:wlan2g";
++ gpios = <&pio 34 GPIO_ACTIVE_LOW>;
++ };
++
++ led-wlan5g {
++ label = "blue:wlan5g";
++ gpios = <&pio 35 GPIO_ACTIVE_LOW>;
++ };
++ };
++};
++
++ð {
++ status = "okay";
++ mediatek,gmac-id = <0>;
++ phy-mode = "2500base-x";
++ mediatek,switch = "mt7531";
++ reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
++
++ fixed-link {
++ speed = <2500>;
++ full-duplex;
++ };
++};
++
++&pio {
++ spi_flash_pins: spi0-pins-func-1 {
++ mux {
++ function = "flash";
++ groups = "spi0", "spi0_wp_hold";
++ };
++
++ conf-pu {
++ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
++ drive-strength = <MTK_DRIVE_8mA>;
++ bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
++ };
++
++ conf-pd {
++ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
++ drive-strength = <MTK_DRIVE_8mA>;
++ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
++ };
++ };
++};
++
++&spi0 {
++ #address-cells = <1>;
++ #size-cells = <0>;
++ pinctrl-names = "default";
++ pinctrl-0 = <&spi_flash_pins>;
++ status = "okay";
++ must_tx;
++ enhance_timing;
++ dma_ext;
++ ipm_design;
++ support_quad;
++ tick_dly = <2>;
++ sample_sel = <0>;
++
++ spi_nand@0 {
++ compatible = "spi-nand";
++ reg = <0>;
++ spi-max-frequency = <52000000>;
++
++ partitions {
++ compatible = "fixed-partitions";
++ #address-cells = <1>;
++ #size-cells = <1>;
++
++ partition@0 {
++ label = "bl2";
++ reg = <0x0 0x100000>;
++ };
++
++ partition@100000 {
++ label = "u-boot-env";
++ reg = <0x100000 0x80000>;
++ };
++
++ partition@180000 {
++ label = "factory";
++ reg = <0x180000 0x200000>;
++ };
++
++ partition@380000 {
++ label = "fip";
++ reg = <0x380000 0x200000>;
++ };
++
++ partition@580000 {
++ label = "config2";
++ reg = <0x580000 0x100000>;
++ };
++
++ partition@680000 {
++ label = "ubi";
++ reg = <0x680000 0xf980000>;
++ };
++ };
++ };
++};
++
++&uart0 {
++ mediatek,force-highspeed;
++ status = "okay";
++};
++
++&watchdog {
++ status = "disabled";
++};
+--- /dev/null
++++ b/defenvs/teralink_tl3020-256mb_env
+@@ -0,0 +1,54 @@
++ipaddr=192.168.1.1
++serverip=192.168.1.254
++loadaddr=0x46000000
++console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0
++bootcmd=if pstore check ; then run boot_recovery ; else run boot_ubi ; fi
++bootconf=config-1
++bootdelay=0
++bootfile=openwrt-mediatek-filogic-teralink_tl3020-256mb-initramfs-recovery.itb
++bootfile_bl2=openwrt-mediatek-filogic-teralink_tl3020-256mb-preloader.bin
++bootfile_fip=openwrt-mediatek-filogic-teralink_tl3020-256mb-bl31-uboot.fip
++bootfile_upg=openwrt-mediatek-filogic-teralink_tl3020-256mb-squashfs-sysupgrade.itb
++bootled_pwr=blue:power
++bootled_rec=red:wan
++bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60
++bootmenu_default=0
++bootmenu_delay=0
++bootmenu_title= \e[0;34m( ( ( \e[1;39mOpenWrt\e[0;34m ) ) )
++bootmenu_0=Initialize environment.=run _firstboot
++bootmenu_0d=Run default boot command.=run boot_default
++bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
++bootmenu_2=Boot production system from NAND.=run boot_production ; run bootmenu_confirm_return
++bootmenu_3=Boot recovery system from NAND.=run boot_recovery ; run bootmenu_confirm_return
++bootmenu_4=Load production system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_5=Load recovery system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_6=\e[31mLoad BL31+U-Boot FIP via TFTP then write to NAND.\e[0m=run boot_tftp_write_fip ; run bootmenu_confirm_return
++bootmenu_7=\e[31mLoad BL2 preloader via TFTP then write to NAND.\e[0m=run boot_tftp_write_bl2 ; run bootmenu_confirm_return
++bootmenu_8=Reboot.=reset
++bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset
++boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu
++boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
++boot_production=led $bootled_pwr on ; run ubi_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off
++boot_recovery=led $bootled_rec on ; run ubi_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off
++boot_ubi=run boot_production ; run boot_recovery ; run boot_tftp_forever
++boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done
++boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run ubi_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run ubi_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp=tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf
++boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run mtd_write_fip && run reset_factory
++boot_tftp_write_bl2=tftpboot $loadaddr $bootfile_bl2 && run mtd_write_bl2
++reset_factory=ubi part ubi ; mw $loadaddr 0x0 0x800 ; ubi write $loadaddr ubootenv 0x800 ; ubi write $loadaddr ubootenv2 0x800
++mtd_write_fip=mtd erase fip && mtd write fip $loadaddr
++mtd_write_bl2=mtd erase bl2 && mtd write bl2 $loadaddr
++ubi_create_env=ubi check ubootenv || ubi create ubootenv 0x100000 dynamic || run ubi_format ; ubi check ubootenv2 || ubi create ubootenv2 0x100000 dynamic || run ubi_format
++ubi_format=ubi detach ; mtd erase ubi && ubi part ubi ; reset
++ubi_prepare_rootfs=if ubi check rootfs_data ; then else if env exists rootfs_data_max ; then ubi create rootfs_data $rootfs_data_max dynamic || ubi create rootfs_data - dynamic ; else ubi create rootfs_data - dynamic ; fi ; fi
++ubi_read_production=ubi read $loadaddr fit && iminfo $loadaddr && run ubi_prepare_rootfs
++ubi_read_recovery=ubi check recovery && ubi read $loadaddr recovery
++ubi_remove_rootfs=ubi check rootfs_data && ubi remove rootfs_data
++ubi_write_production=ubi check fit && ubi remove fit ; run ubi_remove_rootfs ; ubi create fit $filesize dynamic && ubi write $loadaddr fit $filesize
++ubi_write_recovery=ubi check recovery && ubi remove recovery ; run ubi_remove_rootfs ; ubi create recovery $filesize dynamic && ubi write $loadaddr recovery $filesize
++_init_env=setenv _init_env ; run ubi_create_env ; saveenv ; saveenv
++_firstboot=setenv _firstboot ; run _switch_to_menu ; run _init_env ; run boot_first
++_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title
++_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title \e[33m$ver\e[0m"
routerich,ax3000-ubootmod|\
routerich,be7200|\
snr,snr-cpe-ax2|\
+teralink,tl3020-256mb|\
tplink,be450-ubi|\
tplink,tl-xdr4288|\
tplink,tl-xdr6086|\
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2026 Fil Dunsky <filipp.dunsky@gmail.com>
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "mt7981b.dtsi"
+
+/ {
+ model = "Teralink TL3020 256mb";
+ compatible = "teralink,tl3020-256mb", "mediatek,mt7981b";
+
+ aliases {
+ led-boot = &boot_led;
+ led-failsafe = &upgrade_led;
+ led-running = &boot_led;
+ led-upgrade = &upgrade_led;
+ label-mac-device = &gmac0;
+ serial0 = &uart0;
+ };
+
+ chosen: chosen {
+ rootdisk = <&ubi_fit_volume>;
+ stdout-path = "serial0:115200n8";
+ bootargs-append = " root=/dev/fit0 rootwait";
+ };
+
+ memory@40000000 {
+ reg = <0 0x40000000 0 0x10000000>;
+ device_type = "memory";
+ };
+
+ gpio-export {
+ compatible = "gpio-export";
+
+ gpio-0 {
+ gpio-export,name = "usb-enable";
+ gpio-export,output = <1>;
+ gpios = <&pio 14 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ button-0 {
+ label = "wps";
+ /* Reassigned to RF_KILL */
+ linux,code = <KEY_RFKILL>;
+ gpios = <&pio 0 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+
+ button-1 {
+ label = "reset";
+ gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <60>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ upgrade_led: led-wan-red {
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_WAN;
+ gpios = <&pio 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ boot_led: led-power {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_POWER;
+ gpios = <&pio 7 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ led-lan1 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <1>;
+ gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+ };
+
+ led-lan2 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <2>;
+ gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+ };
+
+ led-lan3 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <3>;
+ gpios = <&pio 11 GPIO_ACTIVE_LOW>;
+ };
+
+ led-wan-blue {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_WAN;
+ gpios = <&pio 12 GPIO_ACTIVE_LOW>;
+ };
+
+ led-wlan2g {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_WLAN_2GHZ;
+ gpios = <&pio 34 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ led-wlan5g {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_WLAN_5GHZ;
+ gpios = <&pio 35 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+ };
+};
+
+ð {
+ status = "okay";
+
+ gmac0: mac@0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "2500base-x";
+
+ nvmem-cells = <&macaddr_config_707 0>;
+ nvmem-cell-names = "mac-address";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+};
+
+&mdio_bus {
+ switch: switch@1f {
+ compatible = "mediatek,mt7531";
+ reg = <31>;
+ reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_flash_pins>;
+ status = "okay";
+
+ spi_nand: flash@0 {
+ compatible = "spi-nand";
+ reg = <0>;
+
+ spi-max-frequency = <52000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+
+ spi-cal-enable;
+ spi-cal-mode = "read-data";
+ spi-cal-datalen = <7>;
+ spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4e 0x41 0x4e 0x44>;
+ spi-cal-addrlen = <5>;
+ spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
+
+ partitions: partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "bl2";
+ reg = <0x0 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "u-boot-env (unused)";
+ reg = <0x100000 0x80000>;
+ read-only;
+ };
+
+ partition@180000 {
+ label = "factory";
+ reg = <0x180000 0x200000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory_0: eeprom@0 {
+ reg = <0x0 0x1000>;
+ };
+ };
+ };
+
+ partition@380000 {
+ label = "fip";
+ reg = <0x380000 0x200000>;
+ read-only;
+ };
+
+ partition@580000 {
+ label = "config2";
+ reg = <0x580000 0x100000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_config_60a: macaddr@60a {
+ compatible = "mac-base";
+ reg = <0x60a 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ macaddr_config_68a: macaddr@68a {
+ compatible = "mac-base";
+ reg = <0x68a 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ macaddr_config_707: macaddr@707 {
+ compatible = "mac-base";
+ reg = <0x707 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ macaddr_config_787: macaddr@787 {
+ compatible = "mac-base";
+ reg = <0x787 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+
+ partition@680000 {
+ label = "ubi";
+ compatible = "linux,ubi";
+ reg = <0x680000 0xf980000>;
+
+ volumes {
+ ubi_fit_volume: ubi-volume-fit {
+ volname = "fit";
+ };
+
+ ubi_ubootenv: ubi-volume-ubootenv {
+ volname = "ubootenv";
+ };
+
+ ubi_ubootenv2: ubi-volume-ubootenv2 {
+ volname = "ubootenv2";
+ };
+ };
+ };
+ };
+ };
+};
+
+&switch {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ };
+
+ wan: port@4 {
+ reg = <4>;
+ label = "wan";
+
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_config_787 0>;
+ };
+
+ port@6 {
+ reg = <6>;
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+};
+
+&pio {
+ spi0_flash_pins: spi0-pins {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+
+ conf-pu {
+ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+ };
+
+ conf-pd {
+ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&wifi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ nvmem-cells = <&eeprom_factory_0>;
+ nvmem-cell-names = "eeprom";
+ status = "okay";
+
+ band@0 {
+ reg = <0>;
+ nvmem-cells = <&macaddr_config_68a 0>;
+ nvmem-cell-names = "mac-address";
+ };
+
+ band@1 {
+ reg = <1>;
+ nvmem-cells = <&macaddr_config_60a 0>;
+ nvmem-cell-names = "mac-address";
+ };
+};
+
+&xhci {
+ mediatek,u3p-dis-msk = <0x1>;
+ status = "okay";
+};
ucidef_set_led_netdev "wan-green" "WAN" "mdio-bus:00:green:wan" "wan" "link_1000 tx rx"
ucidef_set_led_netdev "wan-amber" "WAN" "mdio-bus:00:amber:wan" "wan" "link_100 link_10 tx rx"
;;
+teralink,tl3020-256mb)
+ ucidef_set_led_netdev "lan-1" "lan-1" "blue:lan-1" "lan1" "link tx rx"
+ ucidef_set_led_netdev "lan-2" "lan-2" "blue:lan-2" "lan2" "link tx rx"
+ ucidef_set_led_netdev "lan-3" "lan-3" "blue:lan-3" "lan3" "link tx rx"
+ ucidef_set_led_netdev "wan-off" "wan-off" "red:wan" "wan" "link"
+ ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" "link"
+ ;;
totolink,x6000r)
ucidef_set_led_netdev "wan" "wan" "green:wan" "wan" "link tx rx"
;;
routerich,ax3000|\
routerich,ax3000-ubootmod|\
routerich,be7200|\
- tenbay,wr3000k)
+ tenbay,wr3000k|\
+ teralink,tl3020-256mb)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan
;;
asus,tuf-ax4200|\
routerich,ax3000-ubootmod|\
routerich,be7200|\
snr,snr-cpe-ax2|\
+ teralink,tl3020-256mb|\
tplink,be450-ubi|\
tplink,tl-xdr4288|\
tplink,tl-xdr6086|\
qihoo,360t7|\
qihoo,360t7-ubi|\
routerich,ax3000-ubootmod|\
+ teralink,tl3020-256mb|\
tplink,be450-ubi|\
tplink,tl-xdr4288|\
tplink,tl-xdr6086|\
endef
TARGET_DEVICES += tenda_be12-pro
+define Device/teralink_tl3020-256mb
+ DEVICE_VENDOR := Teralink
+ DEVICE_MODEL := TL3020
+ DEVICE_VARIANT := 256mb
+ DEVICE_DTS := mt7981b-teralink-tl3020-256mb
+ DEVICE_DTS_DIR := ../dts
+ UBINIZE_OPTS := -E 5
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ KERNEL_IN_UBI := 1
+ UBOOTENV_IN_UBI := 1
+ IMAGES := sysupgrade.itb
+ KERNEL_INITRAMFS_SUFFIX := -recovery.itb
+ KERNEL := kernel-bin | libdeflate-gzip
+ KERNEL_INITRAMFS := kernel-bin | lzma | \
+ fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
+ IMAGE/sysupgrade.itb := append-kernel | \
+ fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | \
+ append-metadata
+ DEVICE_PACKAGES := kmod-usb3 kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
+ ARTIFACTS := preloader.bin bl31-uboot.fip
+ ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3-1866
+ ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot teralink_tl3020-256mb
+endef
+TARGET_DEVICES += teralink_tl3020-256mb
+
define Device/totolink_x6000r
DEVICE_VENDOR := TOTOLINK
DEVICE_MODEL := X6000R
projects / thirdparty / openwrt.git / commitdiff
