From: Abel Vesa <abel.vesa@oss.qualcomm.com>
Date: Thu, 14 May 2026 13:54:14 +0000 (+0300)
Subject: arm64: dts: qcom: Add Eliza-specific PM7550BA dtsi
X-Git-Tag: v7.2-rc1~131^2~38^2~35
X-Git-Url: http://git.ipfire.org/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=59703108a0c00321f181d021cb83e0d7b610ed61;p=thirdparty%2Flinux.git

arm64: dts: qcom: Add Eliza-specific PM7550BA dtsi

On Eliza, the SPMI arbiter supports multiple bus masters, requiring
explicit selection of the master for each PMIC.

The existing PM7550BA dtsi does not provide a way to describe this,
so introduce an Eliza-specific variant with the appropriate bus
configuration.

This duplication is required due to hardware differences in how the
SPMI bus is exposed on this platform.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260514-eliza-adsp-usb-v5-2-a21056ffd892@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
---

diff --git a/arch/arm64/boot/dts/qcom/pm7550ba-eliza.dtsi b/arch/arm64/boot/dts/qcom/pm7550ba-eliza.dtsi
new file mode 100644
index 0000000000000..18692893ca418
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm7550ba-eliza.dtsi
@@ -0,0 +1,70 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2026 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pm7550ba-thermal {
+			polling-delay-passive = <100>;
+
+			thermal-sensors = <&pm7550ba_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus0 {
+	pm7550ba: pmic@7 {
+		compatible = "qcom,pm7550ba", "qcom,spmi-pmic";
+		reg = <7 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm7550ba_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x7 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm7550ba_gpios: gpio@8800 {
+			compatible = "qcom,pm7550ba-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pm7550ba_gpios 0 0 8>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm7550ba_eusb2_repeater: phy@fd00 {
+			compatible = "qcom,pm7550ba-eusb2-repeater",
+				     "qcom,pm8550b-eusb2-repeater";
+			reg = <0xfd00>;
+			#phy-cells = <0>;
+		};
+	};
+};