From: Sergey Shlukov Date: Tue, 3 Jun 2025 12:08:46 +0000 (+0000) Subject: mediatek: add support for TP-Link Archer AX80v1(US/RU/CA) X-Git-Url: http://git.ipfire.org/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=8b24289a5267e486abd9ccbf4b4ad82f14d545ae;p=thirdparty%2Fopenwrt.git mediatek: add support for TP-Link Archer AX80v1(US/RU/CA) This commit adds support for TP-Link Archer AX80v1(US/RU/CA). Device specification SoC Type: MediaTek MT7986AV, Cortex-A53, 64-bit RAM: ESMT M15T4G16256 (512MB) Flash: ESMT F50L1G41LB (128 MB) Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8) Ethernet: 1x2.5Gbe (WAN/LAN 2.5Gbps), 4xGbE (WAN/LAN 1Gbps, LAN1, LAN2, LAN3) WLAN 2g: MediaTek MT7976GN WLAN 5g: MediaTek MT7976AN LEDs: 1 red,1 green,1 blue status LEDs, Buttons: 4 (Reset,ledswitch,wps,wlan), USB ports: 1 (USB 3.0) Power: 12 VDC, 3,3 A Connector: Barrel Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI slots contain "seconduboot" (also U-Boot 2022.01-rc4) Serial console (UART) V +-------+-------+-------+-------+ | +3.3V | GND | TX | RX | +---+---+-------+-------+-------+ | +--- Don't connect Installation (UART) Place OpenWrt initramfs image on tftp server with IP 192.168.1.2 Attach UART, switch on the router and interrupt the boot process by pressing 'Ctrl-C' Load and run OpenWrt initramfs image: tftpboot initramfs-kernel.bin bootm !!Attention!! is very important! After entering OpenWrt, please set / update the environment variables: fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit" fw_setenv mtdids "spi-nand0=spi-nand0" fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data),8M(mali_data)" fw_setenv tp_boot_idx 0 Run 'sysupgrade -n' with the sysupgrade OpenWrt image from console or Luci WebUI. Recovery Press Reset button and power on the router Navigate to U-Boot recovery web server (192.168.1.1) and upload the OEM firmware Stock layout 0x000000000000-0x000000200000 : "boot" 0x000000200000-0x000000300000 : "u-boot-env" 0x000000300000-0x000003500000 : "ubi0" 0x000003500000-0x000006700000 : "ubi1" 0x000006700000-0x000006f00000 : "userconfig" 0x000006f00000-0x000007300000 : "tp_data" 0x000007300000-0x000007B00000 : "mali_data" ubi0/ubi1 format U-Boot at boot checks that all volumes are in place: +-------------------------------+ | Volume Name: uboot Vol ID: 0| | Volume Name: kernel Vol ID: 1| | Volume Name: rootfs Vol ID: 2| +-------------------------------+ MAC addresses +---------+-------------------+-----------+ | label | 00:eb:xx:xx:xx:be | label | | LAN | 00:eb:xx:xx:xx:be | label | | WAN | 00:eb:xx:xx:xx:bf | label+1 | | WLAN 2g | 00:eb:xx:xx:xx:be | label | | WLAN 5g | 00:eb:xx:xx:xx:bd | label-1 | +---------+-------------------+-----------+ label MAC address was found in UBI partition "tp_data", file "default-mac". OEM wireless eeprom is also there (file "MT7986_EEPROM.bin"). Signed-off-by: Sergey Shlukov Link: https://github.com/openwrt/openwrt/pull/17753 Signed-off-by: Hauke Mehrtens --- diff --git a/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic index 18d6014f079..9654635bca0 100644 --- a/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic +++ b/package/boot/uboot-tools/uboot-envtools/files/mediatek_filogic @@ -135,6 +135,9 @@ smartrg,sdg-8734) local envdev=$(find_mmc_part "u-boot-env" "mmcblk0") ubootenv_add_uci_config "$envdev" "0x0" "0x8000" "0x8000" ;; +tplink,archer-ax80-v1) + ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000" "8" + ;; ubnt,unifi-6-plus) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x80000" "0x10000" ;; diff --git a/target/linux/mediatek/dts/mt7986a-tplink-archer-ax80-v1.dts b/target/linux/mediatek/dts/mt7986a-tplink-archer-ax80-v1.dts new file mode 100644 index 00000000000..841501c7cf5 --- /dev/null +++ b/target/linux/mediatek/dts/mt7986a-tplink-archer-ax80-v1.dts @@ -0,0 +1,332 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; +#include +#include +#include + +#include "mt7986a.dtsi" + +/ { + compatible = "tplink,archer-ax80-v1", "mediatek,mt7986a"; + model = "TP-Link Archer AX80V1"; + + aliases { + serial0 = &uart0; + led-boot = &led_B; + led-failsafe = &led_R; + led-running = &led_B; + led-upgrade = &led_G; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@40000000 { + reg = <0 0x40000000 0 0x20000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + button-reset { + label = "reset"; + linux,code = ; + gpios = <&pio 7 GPIO_ACTIVE_LOW>; + }; + + button-ledswitch { + label = "ledswitch"; + linux,code = ; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + }; + + button-wps { + label = "wps"; + linux,code = ; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + }; + + button-wifi { + label = "wlan"; + linux,code = ; + gpios = <&pio 16 GPIO_ACTIVE_LOW>; + }; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "fixed-1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_5v: regulator-5v { + compatible = "regulator-fixed"; + regulator-name = "fixed-5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; +}; + +&auxadc { + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + fixed-link { + speed = <2500>; + full-duplex; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "2500base-x"; + phy-handle = <&phy6>; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>; + reset-delay-us = <1500000>; + reset-post-delay-us = <1000000>; + + phy6: phy@6 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <6>; + }; + + switch@1f { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <66 IRQ_TYPE_LEVEL_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan0"; + }; + port@1 { + reg = <1>; + label = "lan1"; + }; + port@2 { + reg = <2>; + label = "lan2"; + }; + port@3 { + reg = <3>; + label = "lan3"; + }; + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + fixed-link { + speed = <2500>; + full-duplex; + }; + }; + }; + }; + }; +}; + +&i2c0 { + status = "okay"; + + lp55231: led-controller@32 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lp55231"; + reg = <0x32>; + status = "okay"; + clock-mode = /bits/ 8 <1>; + + led_B: led@0 { + chan-name = "B"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + reg = <0>; + color = ; + }; + + led_G: led@3 { + chan-name = "G"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + reg = <3>; + color = ; + }; + + led_R: led@6 { + chan-name = "R"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + reg = <6>; + color = ; + }; + + }; +}; +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_flash_pins>; + status = "okay"; + + spi_nand_flash: flash@0 { + compatible = "spi-nand"; + reg = <0>; + + spi-max-frequency = <52000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + + spi-cal-enable; + spi-cal-mode = "read-data"; + spi-cal-datalen = <7>; + spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4e 0x41 0x4e 0x44>; + spi-cal-addrlen = <5>; + spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>; + + partitions: partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "boot"; + reg = <0x0 0x200000>; + read-only; + }; + + partition@200000 { + label = "u-boot-env"; + reg = <0x200000 0x100000>; + }; + + partition@300000 { + label = "ubi0"; + reg = <0x300000 0x3200000>; + }; + + partition@3500000 { + label = "ubi1"; + reg = <0x3500000 0x3200000>; + }; + + partition@6700000 { + label = "userconfig"; + reg = <0x6700000 0x800000>; + }; + + factory:partition@6f00000 { + label = "tp_data"; + reg = <0x6f00000 0x400000>; + }; + + partition@7300000 { + label = "mali_data"; + reg = <0x7300000 0x800000>; + }; + }; + }; +}; + +&pio { + spi_flash_pins: spi-flash-pins-33-to-38 { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + conf-pu { + pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP"; + drive-strength = <8>; + mediatek,pull-up-adv = <0>; /* bias-disable */ + }; + conf-pd { + pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO"; + drive-strength = <8>; + mediatek,pull-down-adv = <0>; /* bias-disable */ + }; + }; + wf_2g_5g_pins: wf_2g_5g-pins { + mux { + function = "wifi"; + groups = "wf_2g", "wf_5g"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; +}; + +&trng { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&ssusb { + vusb33-supply = <®_3p3v>; + vbus-supply = <®_5v>; + status = "okay"; +}; + +&usb_phy { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&wf_2g_5g_pins>; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index 7eb69133104..861928d82da 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -134,6 +134,9 @@ mediatek_setup_interfaces() wavlink,wl-wn586x3) ucidef_set_interfaces_lan_wan "lan1 lan2" eth1 ;; + tplink,archer-ax80-v1) + ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3" eth1 + ;; tplink,re6000xd) ucidef_set_interface_lan "lan1 lan2 eth1" ;; @@ -182,6 +185,7 @@ mediatek_setup_macs() wan_mac=$(macaddr_add "$lan_mac" 1) ;; mercusys,mr90x-v1|\ + tplink,archer-ax80-v1|\ tplink,re6000xd) label_mac=$(get_mac_binary "/tmp/tp_data/default-mac" 0) lan_mac=$label_mac diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata index 34aacb93127..1d9db845db6 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata @@ -27,6 +27,14 @@ case "$FIRMWARE" in ;; esac ;; +"mediatek/mt7986_eeprom_mt7976_dual.bin") + case "$board" in + tplink,archer-ax80-v1) + ln -sf /tmp/tp_data/MT7986_EEPROM.bin \ + /lib/firmware/$FIRMWARE + ;; + esac + ;; *) exit 1 ;; diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index f027c306b11..b41e1bfce3e 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -129,6 +129,7 @@ case "$board" in [ "$PHYNBR" = "1" ] && macaddr_add $label_mac -2 > /sys${DEVPATH}/macaddress ;; mercusys,mr90x-v1|\ + tplink,archer-ax80-v1|\ tplink,re6000xd) addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0) [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part b/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part index 1474fad831c..87e51a44294 100644 --- a/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part +++ b/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part @@ -14,6 +14,7 @@ preinit_mount_cfg_part() { case $(board_name) in mercusys,mr80x-v3|\ mercusys,mr90x-v1|\ + tplink,archer-ax80-v1|\ tplink,re6000xd) mount_ubi_part "tp_data" ;; diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh index 9d279898ac5..936ed44ff96 100644 --- a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh +++ b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh @@ -28,6 +28,7 @@ preinit_set_mac_address() { ip link set dev eth1 address "$addr" ;; mercusys,mr90x-v1|\ + tplink,archer-ax80-v1|\ tplink,re6000xd) addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0) ip link set dev eth1 address "$(macaddr_add $addr 1)" diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index 5788b13978d..7d204b91969 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -147,6 +147,7 @@ platform_do_upgrade() { ;; mercusys,mr80x-v3|\ mercusys,mr90x-v1|\ + tplink,archer-ax80-v1|\ tplink,re6000xd) CI_UBIPART="ubi0" nand_do_upgrade "$1" diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 93ba917d3a4..1dc56980341 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -1685,6 +1685,20 @@ define Device/tenbay_wr3000k endef TARGET_DEVICES += tenbay_wr3000k +define Device/tplink_archer-ax80-v1 + DEVICE_VENDOR := TP-Link + DEVICE_MODEL := Archer AX80V1 + DEVICE_DTS := mt7986a-tplink-archer-ax80-v1 + DEVICE_DTS_DIR := ../dts + DEVICE_PACKAGES := kmod-leds-lp5523 kmod-usb3 kmod-mt7915e kmod-mt7986-firmware mt7986-wo-firmware + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 51200k + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += tplink_archer-ax80-v1 + define Device/tplink_re6000xd DEVICE_VENDOR := TP-Link DEVICE_MODEL := RE6000XD