From: Tomasz Maciej Nowak Date: Thu, 29 May 2025 20:15:16 +0000 (+0200) Subject: ath79: add support for Dell SonicPoint ACi APL27-0B1 X-Git-Url: http://git.ipfire.org/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=a89eced3ab2cc8dde322d750a39b4f33369aaa36;p=thirdparty%2Fopenwrt.git ath79: add support for Dell SonicPoint ACi APL27-0B1 Dell/SonicWall APL27-0B1 (marketed as SonicPoint ACi) is a dual band wireless access point. Very similar to already supported APL26-0AE, which all antennas are external, while this variant has internal antennas. End of life as of 2022-07-31. Specification SoC: QualcommAtheros QCA9550 RAM: 256 MB DDR2 Flash: 32 MB SPI NOR WIFI: 2.4 GHz 3T3R integrated 5 GHz 3T3R QCA9890 oversized Mini PCIe card Ethernet: 2x 10/100/1000 Mbps QCA8334 port labeled lan1 is PoE capable (802.3at) USB: 1x 2.0 LEDs: LEDs: 6x which 5 are GPIO controlled and two of them are dual color Buttons: 1x GPIO controlled Serial: RJ-45 port, SonicWall pinout baud: 115200, parity: none, flow control: none Before flashing, be sure to have a copy of factory firmware, in case You wish to revert to original firmware. Installation 1. Prepare TFTP server with OpenWrt sysupgrade image and rename that image to "ap135.bin". 2. Connect to one of LAN ports. 3. Connect to serial port. 4. Hold the reset button (small through hole on side of the unit), power on the device and when prompted to stop autoboot, hit any key. The held button can now be released. 5. Alter U-Boot environment with following commands: setenv bootcmd bootm 0x9F110000 saveenv 6. Adjust "ipaddr" (access point, default is 192.168.1.1) and "serverip" (TFTP server, default is 192.168.1.10) addresses in U-Boot environment, then run following commands: tftp 0x80060000 ap135.bin erase 0x9F110000 +0x1EF0000 cp.b 0x80060000 0x9F110000 $filesize 7. After successful flashing, execute: boot 8. The access point will boot to OpenWrt. Wait few minutes, until the wrench LED will stop blinking, then it's ready for configuration. Notes By default no power is provided on USB port, so attached USB devices won't enumerate. To change that enable regulator with: echo "enabled" > /sys/devices/platform/output-usb-vbus/state To disable power write "disabled" to the same file. Ther regulator state will reset on reboot, consider running this command on hotplug event or add it to /etc/rc.local. The hotplug event should look like this: if [ "${PRODUCT}" = "1d6b/2/606" ] && [ "${ACTION}" = "add" ]; then echo "enabled" > /sys/devices/platform/output-usb-vbus/state fi Place it in /etc/hotplug.d/usb/10-usb-power. Known issues Initramfs image can't be bigger than specified kernel size, otherwise bootloader will throw LZMA decompressing error. Switching to lzma-loader should workaround that. Signed-off-by: Tomasz Maciej Nowak Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250529202033.28250-2-tmn505@terefe.re/ Signed-off-by: Hauke Mehrtens --- diff --git a/package/boot/uboot-tools/uboot-envtools/files/ath79 b/package/boot/uboot-tools/uboot-envtools/files/ath79 index f275244cbe8..f544bfaf79b 100644 --- a/package/boot/uboot-tools/uboot-envtools/files/ath79 +++ b/package/boot/uboot-tools/uboot-envtools/files/ath79 @@ -111,7 +111,8 @@ buffalo,wzr-hp-g300nh-s|\ linksys,ea4500-v3) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000" ;; -dell,apl26-0ae) +dell,apl26-0ae|\ +dell,apl27-0b1) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x10000" ;; domywifi,dw33d) diff --git a/target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts b/target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts index 6ef2eb846d8..044de5add32 100644 --- a/target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts +++ b/target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts @@ -1,29 +1,14 @@ // SPDX-License-Identifier: GPL-2.0-or-later OR MIT -#include -#include -#include - -#include "qca955x.dtsi" +#include "qca9550_dell_apl2x.dtsi" / { model = "Dell SonicPoint ACe (APL26-0AE)"; compatible = "dell,apl26-0ae", "qca,qca9550", "qca,qca9558"; - aliases { - label-mac-device = ð0; - led-boot = &led_wrench; - led-failsafe = &led_wrench; - led-upgrade = &led_wrench; - }; - keys { - compatible = "gpio-keys"; - button-reset { - label = "reset"; gpios = <&gpio 21 GPIO_ACTIVE_LOW>; - linux,code = ; }; /* Accessible only after disassembling the casing */ @@ -35,109 +20,38 @@ }; leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&jtag_disable_pins>; - led-lan1-amber { - color = ; - function = LED_FUNCTION_LAN; - function-enumerator = <1>; gpios = <&gpio 13 GPIO_ACTIVE_LOW>; }; led-lan1-green { - color = ; - function = LED_FUNCTION_LAN; - function-enumerator = <1>; gpios = <&gpio 3 GPIO_ACTIVE_LOW>; }; led-lan2-amber { - color = ; - function = LED_FUNCTION_LAN; - function-enumerator = <2>; gpios = <&gpio 17 GPIO_ACTIVE_LOW>; }; led-lan2-green { - color = ; - function = LED_FUNCTION_LAN; - function-enumerator = <2>; gpios = <&gpio 14 GPIO_ACTIVE_LOW>; }; led-wlan2g { - color = ; - function = LED_FUNCTION_WLAN_2GHZ; - linux,default-trigger = "phy1tpt"; gpios = <&gpio 1 GPIO_ACTIVE_LOW>; }; led-wlan5g { - color = ; - function = LED_FUNCTION_WLAN_5GHZ; - linux,default-trigger = "phy0tpt"; gpios = <&gpio 2 GPIO_ACTIVE_LOW>; }; - led_wrench: led-wrench { - color = ; - function = LED_FUNCTION_STATUS; + led-wrench { gpios = <&gpio 0 GPIO_ACTIVE_LOW>; }; }; }; -ð0 { - status = "okay"; - - nvmem-cells = <&macaddr_sysinfo_50 0>; - nvmem-cell-names = "mac-address"; - phy-handle = <&phy0>; - pll-data = <0xa6000000 0x00000101 0x00001616>; -}; - -ð1 { - status = "okay"; - - nvmem-cells = <&macaddr_sysinfo_50 1>; - nvmem-cell-names = "mac-address"; - pll-data = <0x03000101 0x00000101 0x00001616>; - - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&mdio0 { - status = "okay"; - - phy0: ethernet-phy@0 { - reg = <0>; - - qca,ar8327-initvals = < - 0x04 0x07680000 /* PORT0 PAD MODE CTRL */ - 0x0c 0x00000080 /* PORT6 PAD MODE CTRL */ - 0x10 0x40000000 /* POWER_ON_STRAP */ - 0x50 0xffb7c405 /* LED0 CTRL */ - 0x54 0xffb7c305 /* LED1 CTRL */ - 0x58 0xffb7c033 /* LED2 CTRL */ - 0x5c 0x03ffff00 /* LED3 CTRL */ - 0x7c 0x0000007e /* PORT0_STATUS */ - 0x94 0x0000007e /* PORT6_STATUS */ - >; - }; -}; - &pcie0 { - status = "okay"; - wifi@0,0 { - compatible = "qcom,ath10k"; - reg = <0x0000 0 0 0 0>; - /* OEM overwrites EEPROM stored adress and so do we */ nvmem-cells = <&macaddr_sysinfo_50 2>; nvmem-cell-names = "mac-address"; @@ -145,84 +59,7 @@ }; &spi { - status = "okay"; - flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <25000000>; broken-flash-reset; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x0080000>; - read-only; - }; - - partition@80000 { - label = "u-boot-env"; - reg = <0x0080000 0x0040000>; - }; - - partition@c0000 { - label = "sysinfo"; - reg = <0x00c0000 0x0040000>; - read-only; - - nvmem-layout { - compatible = "fixed-layout"; - #address-cells = <1>; - #size-cells = <1>; - - macaddr_sysinfo_50: macaddr@50 { - compatible = "mac-base"; - reg = <0x50 0x6>; - #nvmem-cell-cells = <1>; - }; - }; - }; - - partition@100000 { - label = "art"; - reg = <0x0100000 0x0010000>; - read-only; - - nvmem-layout { - compatible = "fixed-layout"; - #address-cells = <1>; - #size-cells = <1>; - - cal_art_1000: calibration@1000 { - reg = <0x1000 0x440>; - }; - }; - }; - - partition@110000 { - label = "firmware"; - reg = <0x0110000 0x1ef0000>; - compatible = "denx,uimage"; - }; - }; }; }; - -&usb_phy0 { - status = "okay"; -}; - -&usb0 { - status = "okay"; -}; - -&wmac { - status = "okay"; - - nvmem-cells = <&macaddr_sysinfo_50 10>, <&cal_art_1000>; - nvmem-cell-names = "mac-address", "calibration"; -}; diff --git a/target/linux/ath79/dts/qca9550_dell_apl27-0b1.dts b/target/linux/ath79/dts/qca9550_dell_apl27-0b1.dts new file mode 100644 index 00000000000..28d78f29d21 --- /dev/null +++ b/target/linux/ath79/dts/qca9550_dell_apl27-0b1.dts @@ -0,0 +1,78 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca9550_dell_apl2x.dtsi" + +/ { + model = "Dell SonicPoint ACi (APL27-0B1)"; + compatible = "dell,apl27-0b1", "qca,qca9550", "qca,qca9558"; + + keys { + button-reset { + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + led-lan1-amber { + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + }; + + led-lan1-green { + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + }; + + led-lan2-amber { + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + }; + + led-lan2-green { + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + }; + + led-wlan2g { + gpios = <&gpio 21 GPIO_ACTIVE_LOW>; + }; + + led-wlan5g { + gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + }; + + led-wrench { + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + }; + + reg_usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + + output-usb-vbus { + compatible = "regulator-output"; + vout-supply = <®_usb_vbus>; + }; +}; + +&pcie0 { + wifi@0,0 { + nvmem-cells = <&macaddr_sysinfo_50 2>, <&cal_art_5000>; + nvmem-cell-names = "mac-address", "calibration"; + }; +}; + +&spi { + flash@0 { + partitions { + partition@100000 { + nvmem-layout { + cal_art_5000: calibration@5000 { + reg = <0x5000 0x844>; + }; + }; + }; + }; + }; +}; diff --git a/target/linux/ath79/dts/qca9550_dell_apl2x.dtsi b/target/linux/ath79/dts/qca9550_dell_apl2x.dtsi new file mode 100644 index 00000000000..bcc558e0b15 --- /dev/null +++ b/target/linux/ath79/dts/qca9550_dell_apl2x.dtsi @@ -0,0 +1,207 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include +#include +#include + +#include "qca955x.dtsi" + +/ { + aliases { + label-mac-device = ð0; + led-boot = &led_wrench; + led-failsafe = &led_wrench; + led-upgrade = &led_wrench; + }; + + keys { + compatible = "gpio-keys"; + + button-reset { + label = "reset"; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&jtag_disable_pins>; + + led-lan1-amber { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <1>; + }; + + led-lan1-green { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <1>; + }; + + led-lan2-amber { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <2>; + }; + + led-lan2-green { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <2>; + }; + + led-wlan2g { + color = ; + function = LED_FUNCTION_WLAN_2GHZ; + linux,default-trigger = "phy1tpt"; + }; + + led-wlan5g { + color = ; + function = LED_FUNCTION_WLAN_5GHZ; + linux,default-trigger = "phy0tpt"; + }; + + led_wrench: led-wrench { + color = ; + function = LED_FUNCTION_STATUS; + }; + }; +}; + +ð0 { + status = "okay"; + + nvmem-cells = <&macaddr_sysinfo_50 0>; + nvmem-cell-names = "mac-address"; + phy-handle = <&phy0>; + pll-data = <0xa6000000 0x00000101 0x00001616>; +}; + +ð1 { + status = "okay"; + + nvmem-cells = <&macaddr_sysinfo_50 1>; + nvmem-cell-names = "mac-address"; + pll-data = <0x03000101 0x00000101 0x00001616>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&mdio0 { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <0>; + + qca,ar8327-initvals = < + 0x04 0x07680000 /* PORT0 PAD MODE CTRL */ + 0x0c 0x00000080 /* PORT6 PAD MODE CTRL */ + 0x10 0x40000000 /* POWER_ON_STRAP */ + 0x50 0xffb7c405 /* LED0 CTRL */ + 0x54 0xffb7c305 /* LED1 CTRL */ + 0x58 0xffb7c033 /* LED2 CTRL */ + 0x5c 0x03ffff00 /* LED3 CTRL */ + 0x7c 0x0000007e /* PORT0_STATUS */ + 0x94 0x0000007e /* PORT6_STATUS */ + >; + }; +}; + +&pcie0 { + status = "okay"; + + wifi@0,0 { + compatible = "qcom,ath10k"; + reg = <0x0000 0 0 0 0>; + }; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x0080000>; + read-only; + }; + + partition@80000 { + label = "u-boot-env"; + reg = <0x0080000 0x0040000>; + }; + + partition@c0000 { + label = "sysinfo"; + reg = <0x00c0000 0x0040000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_sysinfo_50: macaddr@50 { + compatible = "mac-base"; + reg = <0x50 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@100000 { + label = "art"; + reg = <0x0100000 0x0010000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + cal_art_1000: calibration@1000 { + reg = <0x1000 0x440>; + }; + }; + }; + + partition@110000 { + label = "firmware"; + reg = <0x0110000 0x1ef0000>; + compatible = "denx,uimage"; + }; + }; + }; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&wmac { + status = "okay"; + + nvmem-cells = <&macaddr_sysinfo_50 10>, <&cal_art_1000>; + nvmem-cell-names = "mac-address", "calibration"; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index 41075634398..9ebdcdca6fa 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -234,7 +234,8 @@ compex,wpj531-16m) ucidef_set_led_rssi "sig3" "SIG3" "green:sig3" "wlan0" "65" "100" ucidef_set_led_rssi "sig4" "SIG4" "green:sig4" "wlan0" "50" "100" ;; -dell,apl26-0ae) +dell,apl26-0ae|\ +dell,apl27-0b1) ucidef_set_led_switch "lan1" "LAN1" "amber:lan-1" "switch0" "0x04" ucidef_set_led_switch "lan2" "LAN2" "amber:lan-2" "switch0" "0x08" ;; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index d999784d6a2..545bc14e366 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -298,7 +298,8 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "1:wan" "5:lan" "6@eth0" ;; - dell,apl26-0ae) + dell,apl26-0ae|\ + dell,apl27-0b1) ucidef_add_switch "switch0" \ "0@eth0" "2:lan:1" "3:lan:2" "6@eth1" ;; diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index b74a22ba4d6..6e97960207a 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -978,22 +978,34 @@ define Device/compex_wpj563 endef TARGET_DEVICES += compex_wpj563 -define Device/dell_apl26-0ae +define Device/dell_apl2x SOC := qca9550 DEVICE_VENDOR := Dell DEVICE_MODEL := SonicPoint - DEVICE_VARIANT := ACe (APL26-0AE) DEVICE_ALT0_VENDOR := SonicWall DEVICE_ALT0_MODEL := SonicPoint - DEVICE_ALT0_VARIANT := ACe (APL26-0AE) DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2 KERNEL_SIZE := 5952k IMAGE_SIZE := 31680k IMAGE/sysupgrade.bin = append-kernel | pad-to $$$$(BLOCKSIZE) | \ append-rootfs | pad-rootfs | check-size | append-metadata endef + +define Device/dell_apl26-0ae + $(Device/dell_apl2x) + DEVICE_VARIANT := ACe (APL26-0AE) + DEVICE_ALT0_VARIANT := ACe (APL26-0AE) +endef TARGET_DEVICES += dell_apl26-0ae +define Device/dell_apl27-0b1 + $(Device/dell_apl2x) + DEVICE_VARIANT := ACi (APL27-0B1) + DEVICE_ALT0_VARIANT := ACi (APL27-0B1) + DEVICE_PACKAGES += kmod-regulator-userspace-consumer +endef +TARGET_DEVICES += dell_apl27-0b1 + define Device/devolo_dlan-pro-1200plus-ac SOC := ar9344 DEVICE_VENDOR := devolo