From: Derek Denk Date: Wed, 31 Dec 2025 00:34:47 +0000 (-0700) Subject: mediatek: filogic: add support for Cudy AP3000 Wall v1 X-Git-Url: http://git.ipfire.org/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=afad4c71f8d558ca86b997781ca0236f321cf1e9;p=thirdparty%2Fopenwrt.git mediatek: filogic: add support for Cudy AP3000 Wall v1 This commit adds support for the Cudy AP3000 Wall v1. SoC: MediaTek MT7981b RAM: 256MiB Flash: spi-nand spi0.0: 128 MiB Wifi: MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5) LEDs: 1 LED in two colors (red & white) Buttons: 1 reset, 1 led on/off Ethernet: 5x 1GbE Power: PoE powered (standalone) The stock firmware is a customized variant of OpenWrt, which implements a signature check that only allows flashing official firmware. Cudy offers intermediate OpenWrt firmware images on their website [1][2] which do not implement the signature check. After flashing the intermediate image the upstream official OpenWrt image can be installed. The stock firmware can be recovered via TFTP using the U-Boot based boot loader[3]. Set up a TFTP server on your computer with IP 192.168.1.88/24 serving the stock firmware from Cudy's website renamed to "recovery.bin". Press and hold the reset button while powering on the device, wait for the TFTP server to send the recovery.bin file, then release the reset button. The router will take a couple of minutes to reboot and set up the stock firmware. [1] https://www.cudy.com/blogs/faq/openwrt-software-download [2] https://drive.google.com/drive/folders/1BKVarlwlNxf7uJUtRhuMGUqeCa5KpMnj [3] https://www.cudy.com/en-us/blogs/faq/how-to-recovery-the-cudy-router-from-openwrt-firmware-to-cudy-official-firmware Signed-off-by: Derek Denk Link: https://github.com/openwrt/openwrt/pull/21266 Signed-off-by: Hauke Mehrtens --- diff --git a/target/linux/mediatek/dts/mt7981b-cudy-ap3000wall-v1.dts b/target/linux/mediatek/dts/mt7981b-cudy-ap3000wall-v1.dts new file mode 100644 index 00000000000..adcbfdd9c56 --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-cudy-ap3000wall-v1.dts @@ -0,0 +1,276 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; + +#include + +#include "mt7981b.dtsi" + +/ { + model = "Cudy AP3000 Wall v1"; + compatible = "cudy,ap3000wall-v1", "mediatek,mt7981"; + + aliases { + label-mac-device = &gmac0; + led-boot = &led_status_white; + led-failsafe = &led_status_red; + led-running = &led_status_white; + led-upgrade = &led_status_red; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + }; + + lights_toggle { + label = "lights_toggle"; + linux,code = ; + gpios = <&pio 35 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + led_status_red: led@0 { + label = "red:status"; + function = LED_FUNCTION_POWER; + color = ; + gpios = <&pio 4 GPIO_ACTIVE_LOW>; + }; + + led_status_white: led@1 { + label = "white:status"; + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + }; + + }; + + gpio_export { + compatible = "gpio-export"; + + poe_passthrough { + gpio-export,name = "poe-passthrough"; + gpio-export,output = <0>; + gpios = <&pio 12 GPIO_ACTIVE_HIGH>; + }; + }; + + watchdog-hw { + compatible = "linux,wdt-gpio"; + gpios = <&pio 6 GPIO_ACTIVE_HIGH>; + hw_algo = "level"; + hw_margin_ms = <10000>; + always-running; + }; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +ð { + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins>; + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_bdinfo_de00 0>; + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; +}; + +&mdio_bus { + switch: switch@1f { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + spi_nand: flash@0 { + compatible = "spi-nand"; + reg = <0>; + spi-max-frequency = <52000000>; + + spi-cal-enable; + spi-cal-mode = "read-data"; + spi-cal-datalen = <7>; + spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>; + spi-cal-addrlen = <5>; + spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>; + + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x00000 0x0100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x0100000 0x0080000>; + read-only; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x180000 0x0200000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0x1000>; + }; + }; + }; + + partition@380000 { + label = "bdinfo"; + reg = <0x380000 0x0040000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_bdinfo_de00: macaddr@de00 { + compatible = "mac-base"; + reg = <0xde00 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@3c0000 { + label = "FIP"; + reg = <0x3c0000 0x0200000>; + read-only; + }; + + partition@5c0000 { + label = "ubi"; + reg = <0x5c0000 0x4000000>; + compatible = "linux,ubi"; + }; + }; + }; +}; + +&pio { + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + conf-pu { + pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; + drive-strength = ; + bias-pull-up = ; + }; + conf-pd { + pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; + drive-strength = ; + bias-pull-down = ; + }; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "lan5"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&wifi { + status = "okay"; + nvmem-cells = <&eeprom_factory_0>; + nvmem-cell-names = "eeprom"; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index c465a970223..c69bd3abcb8 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -106,6 +106,9 @@ mediatek_setup_interfaces() comfast,cf-e393ax) ucidef_set_interfaces_lan_wan "lan1" eth1 ;; + cudy,ap3000wall-v1) + ucidef_set_interface_lan "lan1 lan2 lan3 lan4 lan5" + ;; cudy,ap3000outdoor-v1|\ cudy,ap3000-v1|\ cudy,re3000-v1|\ diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index 60d4528227e..937f4f49c0a 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -84,6 +84,7 @@ case "$board" in [ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress ;; cudy,ap3000outdoor-v1|\ + cudy,ap3000wall-v1|\ cudy,ap3000-v1|\ cudy,m3000-v1|\ cudy,re3000-v1|\ diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index b395f5f907f..86e3e095b1e 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -1027,6 +1027,23 @@ define Device/cudy_ap3000outdoor-v1 endef TARGET_DEVICES += cudy_ap3000outdoor-v1 +define Device/cudy_ap3000wall-v1 + DEVICE_VENDOR := Cudy + DEVICE_MODEL := AP3000 Wall + DEVICE_VARIANT := v1 + DEVICE_DTS := mt7981b-cudy-ap3000wall-v1 + DEVICE_DTS_DIR := ../dts + SUPPORTED_DEVICES += R68 + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 65536k + KERNEL_IN_UBI := 1 + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware +endef +TARGET_DEVICES += cudy_ap3000wall-v1 + define Device/cudy_ap3000-v1 DEVICE_VENDOR := Cudy DEVICE_MODEL := AP3000