From: Andrew LaMarche Date: Sun, 1 Dec 2024 15:29:48 +0000 (+0000) Subject: realtek: add support for Hasivo S1100W-8XGT-SE switch X-Git-Url: http://git.ipfire.org/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=refs%2Fpull%2F17137%2Fhead;p=thirdparty%2Fopenwrt.git realtek: add support for Hasivo S1100W-8XGT-SE switch This commit adds support for Hasivo S1100W-8XGT-SE switch. Device specification -------------------- SoC Type: RTL9303 RAM: Samsung K4B461646E-BYKO (512MB) Flash: Fudan FM25Q128A (16 MB) Ethernet: 8x 10G via 2x RTL8264 PHY LEDs: 2 LEDs, 1 power green, 1 system green Button: Reset USB ports: None Bootloader: Realtek U-Boot - U-Boot 2011.12.(3.6.6.55087) (Nov 13 2022 - 14:37:31) Fan: 2 fans controlled by STC8G1K08 TSOP-20 microcontroller Note: The fan appears to operate the same irrespective of the running firmware. The STC9G1K08 is likely operating independently. To explore the stock vendor firmware, there are 2 avenues to gain root access. This is not necessary to install OpenWrt, but is here for reference. Root access via serial ---------------------- 1. ctrl+t 2. password: switchrtk 3. press 's' for shell Root access via SSH ------------------- 1. ctrl+t 2. password: switchrtk 3. sys command sh 4. log in with your username+password 5. ctrl+t 6. password: switchrtk 7. press 's' for shell Credit to https://forum.openwrt.org/t/hasivo-switches/151758/174 for rooting instructions. Installing OpenWrt ------------------ 1. Connect to UART. UART requires soldering an RJ45 connector to the console footprint on the board. The header is on the top right of this image: https://forum.openwrt.org/uploads/default/original/3X/4/d/4d2ab97fad7e2c5b0a0bdca4de887918c6dcff97.jpeg 2. Set computer IP to 192.168.0.111. 3. Enter bootloader by pressing esc key during boot. 4. Enter password 'Hs2021cfgmg'. 5. Type 'XXXX'. 6. setenv bootcmd 'rtk network on; bootm 0xb4300000' 7. saveenv 8. rtk network on 9. tftpboot 0x84f00000 10. bootm 0x84f00000 Now you can copy over the sysupgrade image and install. Credit to https://forum.openwrt.org/t/hasivo-switches/151758/22?u=andrewjlamarche for u-boot console access instructions. Signed-off-by: Andrew LaMarche Link: https://github.com/openwrt/openwrt/pull/17137 Signed-off-by: Hauke Mehrtens --- diff --git a/target/linux/realtek/dts/rtl9303_hasivo_s1100w-8xgt-se.dts b/target/linux/realtek/dts/rtl9303_hasivo_s1100w-8xgt-se.dts new file mode 100644 index 00000000000..a156984a23b --- /dev/null +++ b/target/linux/realtek/dts/rtl9303_hasivo_s1100w-8xgt-se.dts @@ -0,0 +1,275 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/dts-v1/; + +#include "rtl930x.dtsi" + +#include +#include +#include + +/ { + compatible = "hasivo,s1100w-8xgt-se", "realtek,rtl930x-soc"; + model = "Hasivo S1100W-8XGT-SE"; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x10000000>, /* 256 MiB lowmem */ + <0x20000000 0x10000000>; /* 256 MiB highmem */ + }; + + aliases { + led-boot = &led_sys; + led-failsafe = &led_sys; + led-running = &led_sys; + led-upgrade = &led_sys; + }; + + chosen { + stdout-path = "serial0:38400n8"; + }; + + keys { + compatible = "gpio-keys"; + + button-reset { + label = "reset"; + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_sys: led-0 { + gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_STATUS; + }; + }; + + led_set { + compatible = "realtek,rtl9300-leds"; + active-low; + + /* + * LED set 0 + * + * - LED[0](Amber): 5G/LINK/ACT + * - LED[1](Green): 10G/LINK/ACT + * - LED[2](Amber): 1G/100M/10M/LINK/ACT + * - LED[3](Green): 2.5G/LINK/ACT + */ + led_set0 = <0x0a02 0x0a01 0x0ba0 0x0a08>; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + /* stock is LOADER */ + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x00e0000>; + read-only; + }; + + /* stock is BDINFO */ + partition@e0000 { + label = "u-boot-env"; + reg = <0x00e0000 0x0010000>; + }; + + /* stock is SYSINFO */ + partition@f0000 { + label = "u-boot-env2"; + reg = <0x00f0000 0x0010000>; + read-only; + }; + + /* stock is JFFS2_CFG */ + partition@100000 { + label = "jffs"; + reg = <0x0100000 0x0100000>; + }; + + /* stock is JFFS2_LOG */ + partition@200000 { + label = "jffs2"; + reg = <0x0200000 0x0100000>; + }; + + /* stock is RUNTIME */ + partition@300000 { + compatible = "openwrt,uimage", "denx,uimage"; + label = "firmware"; + reg = <0x0300000 0x0c00000>; + }; + + /* stock is OEMINFO */ + partition@f00000 { + label = "oeminfo"; + reg = <0x0f00000 0x0100000>; + read-only; + }; + }; + }; +}; + +ðernet0 { + mdio: mdio-bus { + compatible = "realtek,rtl838x-mdio"; + regmap = <ðernet0>; + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + rtl9300,smi-address = <0 0>; + reg = <0>; + sds = <2>; + }; + + phy8: ethernet-phy@8 { + compatible = "ethernet-phy-ieee802.3-c45"; + rtl9300,smi-address = <0 1>; + reg = <8>; + sds = <3>; + }; + + phy16: ethernet-phy@16 { + compatible = "ethernet-phy-ieee802.3-c45"; + rtl9300,smi-address = <0 2>; + reg = <16>; + sds = <4>; + }; + + phy20: ethernet-phy@20 { + compatible = "ethernet-phy-ieee802.3-c45"; + rtl9300,smi-address = <0 3>; + reg = <20>; + sds = <5>; + }; + + phy24: ethernet-phy@24 { + compatible = "ethernet-phy-ieee802.3-c45"; + rtl9300,smi-address = <3 16>; + reg = <24>; + sds = <6>; + }; + + phy25: ethernet-phy@25 { + compatible = "ethernet-phy-ieee802.3-c45"; + rtl9300,smi-address = <3 17>; + reg = <25>; + sds = <7>; + }; + + phy26: ethernet-phy@26 { + compatible = "ethernet-phy-ieee802.3-c45"; + rtl9300,smi-address = <3 18>; + reg = <26>; + sds = <8>; + }; + + phy27: ethernet-phy@27 { + compatible = "ethernet-phy-ieee802.3-c45"; + rtl9300,smi-address = <3 19>; + reg = <27>; + sds = <9>; + }; + }; +}; + +&switch0 { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + phy-mode = "usxgmii"; + phy-handle = <&phy0>; + led-set = <0>; + }; + + port@8 { + reg = <8>; + label = "lan2"; + phy-mode = "usxgmii"; + phy-handle = <&phy8>; + led-set = <0>; + }; + + port@16 { + reg = <16>; + label = "lan3"; + phy-mode = "usxgmii"; + phy-handle = <&phy16>; + led-set = <0>; + }; + + port@20 { + reg = <20>; + label = "lan4"; + phy-mode = "usxgmii"; + phy-handle = <&phy20>; + led-set = <0>; + }; + + port@24 { + reg = <24>; + label = "lan5"; + phy-mode = "usxgmii"; + phy-handle = <&phy24>; + led-set = <0>; + }; + + port@25 { + reg = <25>; + label = "lan6"; + phy-mode = "usxgmii"; + phy-handle = <&phy25>; + led-set = <0>; + }; + + port@26 { + reg = <26>; + label = "lan7"; + phy-mode = "usxgmii"; + phy-handle = <&phy26>; + led-set = <0>; + }; + + port@27 { + reg = <27>; + label = "lan8"; + phy-mode = "usxgmii"; + phy-handle = <&phy27>; + led-set = <0>; + }; + + /* Internal SoC */ + port@28 { + ethernet = <ðernet0>; + reg = <28>; + phy-mode = "internal"; + + fixed-link { + speed = <10000>; + full-duplex; + }; + }; + }; +}; diff --git a/target/linux/realtek/image/rtl930x.mk b/target/linux/realtek/image/rtl930x.mk index 28c17d6c48f..44940c5c1cf 100644 --- a/target/linux/realtek/image/rtl930x.mk +++ b/target/linux/realtek/image/rtl930x.mk @@ -5,6 +5,19 @@ define Build/xikestor-nosimg mv $@.new $@ endef +define Device/hasivo_s1100w-8xgt-se + SOC := rtl9303 + DEVICE_VENDOR := Hasivo + DEVICE_MODEL := S1100W-8XGT-SE + IMAGE_SIZE := 12288k + KERNEL_INITRAMFS := \ + kernel-bin | \ + append-dtb | \ + lzma | \ + uImage lzma +endef +TARGET_DEVICES += hasivo_s1100w-8xgt-se + define Device/tplink_tl-st1008f_v2 SOC := rtl9303 UIMAGE_MAGIC := 0x93030000 diff --git a/target/linux/realtek/rtl930x/config-6.12 b/target/linux/realtek/rtl930x/config-6.12 index 3b3bcae8db3..531360df5ff 100644 --- a/target/linux/realtek/rtl930x/config-6.12 +++ b/target/linux/realtek/rtl930x/config-6.12 @@ -195,6 +195,7 @@ CONFIG_REGMAP_I2C=y CONFIG_REGMAP_MDIO=y CONFIG_REGMAP_MMIO=y CONFIG_RESET_CONTROLLER=y +CONFIG_RTL8261N_PHY=y # CONFIG_RTL838X is not set # CONFIG_RTL839X is not set CONFIG_RTL930X=y