From: INAGAKI Hiroshi Date: Tue, 3 Jun 2025 15:08:06 +0000 (+0900) Subject: qualcommax: add support for I-O DATA WN-DAX3000GR X-Git-Url: http://git.ipfire.org/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=refs%2Fpull%2F19053%2Fhead;p=thirdparty%2Fopenwrt.git qualcommax: add support for I-O DATA WN-DAX3000GR I-O DATA WN-DAX3000GR is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on IPQ5018. Specification: - SoC : Qualcomm IPQ5018 - RAM : DDR3 512 MiB - Flash : SPI-NAND 128 MiB (Macronix MX35UF1G24AD-Z4I) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : Qualcomm IPQ5018 (SoC) - 5 GHz : Qualcomm Atheros QCN6102 - Ethernet : 5x 10/100/1000 Mbps - wan (phy) : Qualcomm IPQ5018 (SoC) - lan (switch) : Qualcomm Atheros QCA8337 - LEDs/Keys (GPIO): 7x/5x - UART : through-hole on PCB (J3) - assignment : 3.3V, TX, RX, NC, GND from tri-angle marking - settings : 115200n8 - USB : USB 2.0 Type-A (through-hole on PCB, "J6") - Power : 12 VDC, 1A (Typ. 930 mA) Flash instruction using factory.bin image: 1. Boot WN-DAX3000GR with router mode 2. Access to the WebUI ("http://192.168.0.1/") on the device and open the firmware update page ("ファームウェア") 3. Select the OpenWrt factory.bin image and click update ("更新") button 4. Wait ~120 seconds to complete flashing Switching to the stock firmware: 1. Load the elecom.sh script . /lib/upgrade/elecom.sh 2. Check the current index of rootfs bootconfig_rw_index 0:bootconfig rootfs 3. Set the index to inverted value bootconfig_rw_index 0:bootconfig rootfs bootconfig_rw_index 0:bootconfig1 rootfs example: - step2 returned "0": bootconfig_rw_index 0:bootconfig rootfs 1 bootconfig_rw_index 0:bootconfig1 rootfs 1 - step2 returned "1": bootconfig_rw_index 0:bootconfig rootfs 0 bootconfig_rw_index 0:bootconfig1 rootfs 0 4. Reboot Partition Layout (Stock FW, bootconfig(rootfs)=1): 0x000000000000-0x000000080000 : "0:SBL1" 0x000000080000-0x000000100000 : "0:MIBIB" 0x000000100000-0x000000140000 : "0:BOOTCONFIG" 0x000000140000-0x000000180000 : "0:BOOTCONFIG1" 0x000000180000-0x000000280000 : "0:QSEE" 0x000000280000-0x000000380000 : "0:QSEE_1" 0x000000380000-0x0000003c0000 : "0:DEVCFG" 0x0000003c0000-0x000000400000 : "0:DEVCFG_1" 0x000000400000-0x000000440000 : "0:CDT" 0x000000440000-0x000000480000 : "0:CDT_1" 0x000000480000-0x000000500000 : "0:APPSBLENV" 0x000000500000-0x000000640000 : "0:APPSBL" 0x000000640000-0x000000780000 : "0:APPSBL_1" 0x000000780000-0x000000880000 : "0:ART" 0x000000880000-0x000000900000 : "0:TRAINING" 0x000000900000-0x000003c40000 : "rootfs_1" 0x000003c40000-0x000003fc0000 : "Config" 0x000003fc0000-0x000007300000 : "rootfs" 0x000007300000-0x000007680000 : "Config_2" 0x000007680000-0x000007700000 : "idmkey" 0x000007700000-0x000007c00000 : "Reserved" 0x000007c00000-0x000007c80000 : "FWHEADER" 0x000007c80000-0x000007d00000 : "Factory" Known Issues: - This device has a Macronix MX35UF1G24AD SPI-NAND chip registered as oobsize=128 in Linux Kernel. But using BCH8 breaks I/O on the chip with the following errors, so this support uses BCH4 instead. [ 1.542261] 0x000000480000-0x000000500000 : "0:appsblenv" [ 1.547959] 1 fixed-partitions partitions found on MTD device 0:appsblenv [ 1.551265] Creating 1 MTD partitions on "0:appsblenv": [ 1.558096] 0x000000000000-0x000000040000 : "env-data" [ 1.627282] u-boot-env-layout 79b0000.qpic-nand:flash@0:partitions:partition-0-appsblenv:partition@0:nvmem-layout: probe with driver u-boot-env-layout failed with error -74 root@OpenWrt:~# strings /dev/mtdblock10 [ 77.806720] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead. [ 77.807554] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0 [ 77.815977] I/O error, dev mtdblock10, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0 [ 77.824721] I/O error, dev mtdblock10, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0 [ 77.834095] I/O error, dev mtdblock10, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 77.843278] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 77.851577] Buffer I/O error on dev mtdblock10, logical block 0, async page read Notes: - This device has dual-boot feature and it's managed by the index in the 0:bootconfig and 0:bootconfig1 partitions. - There are through-holes on PCB for USB 2.0, but it cannot be accessed without disassembly of the housing. So it's not enabled in this support. - WN-DAX3000GR has the "bt_fw" volume in the firmware UBI in addition to the volumes that will be removed in the section of ELECOM WRC-X3000GS2 in /lib/upgrade/platform.sh. That volume is unnecessary for OpenWrt and add `remove_oem_ubi_volume bt_fw` to remove that volume when sysupgrade. (that function doesn't anything without errors if no specified volume) MAC Addresses: LAN : 50:41:B9:xx:xx:64 (0:APPSBLENV, "ethaddr"/"eth1addr" (text)) WAN : 50:41:B9:xx:xx:66 (0:APPSBLENV, "eth0addr" (text)) 2.4 GHz: 50:41:B9:xx:xx:64 (0:APPSBLENV, "wifi0" (text)) 5 GHz : 50:41:B9:xx:xx:65 (0:APPSBLENV, "wifi1" (text)) Signed-off-by: INAGAKI Hiroshi Link: https://github.com/openwrt/openwrt/pull/19053 Signed-off-by: Robert Marko --- diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index c46caf42570..5b64161d317 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -43,6 +43,7 @@ ALLWIFIBOARDS:= \ glinet_gl-ax1800 \ glinet_gl-axt1800 \ glinet_gl-b3000 \ + iodata_wn-dax3000gr \ linksys_homewrk \ linksys_mr5500 \ linksys_mr7350 \ @@ -198,6 +199,7 @@ $(eval $(call generate-ipq-wifi-package,elecom_wrc-x3000gs2,ELECOM WRC-X3000GS2) $(eval $(call generate-ipq-wifi-package,glinet_gl-ax1800,GL.iNet GL-AX1800)) $(eval $(call generate-ipq-wifi-package,glinet_gl-axt1800,GL.iNet GL-AXT1800)) $(eval $(call generate-ipq-wifi-package,glinet_gl-b3000,GL.iNet GL-B3000)) +$(eval $(call generate-ipq-wifi-package,iodata_wn-dax3000gr,I-O DATA WN-DAX3000GR)) $(eval $(call generate-ipq-wifi-package,linksys_homewrk,Linksys HomeWRK)) $(eval $(call generate-ipq-wifi-package,linksys_mr5500,Linksys MR5500)) $(eval $(call generate-ipq-wifi-package,linksys_mr7350,Linksys MR7350)) diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq5018-wn-dax3000gr.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq5018-wn-dax3000gr.dts new file mode 100644 index 00000000000..39df85f0b70 --- /dev/null +++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq5018-wn-dax3000gr.dts @@ -0,0 +1,502 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; + +#include "ipq5018.dtsi" +#include "ipq5018-ess.dtsi" + +#include +#include +#include + +/ { + model = "I-O DATA WN-DAX3000GR"; + compatible = "iodata,wn-dax3000gr", "qcom,ipq5018"; + + aliases { + serial0 = &blsp1_uart1; + led-boot = &led_status_green; + led-failsafe = &led_status_red; + led-upgrade = &led_status_green; + label-mac-device = <&dp1>; + }; + + chosen { + bootargs-append = " root=/dev/ubiblock0_1 coherent_pool=2M"; + stdout-path = "serial0:115200n8"; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + button-reset { + label = "reset"; + gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + switch-led-on { + label = "led-on"; + gpios = <&tlmm 23 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + + switch-repeater { + label = "repeater"; + gpios = <&tlmm 31 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + + switch-ap { + label = "ap"; + gpios = <&tlmm 32 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + + button-wps { + label = "wps"; + gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + led-0 { + gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_WPS; + }; + + led_status_green: led-1 { + gpios = <&tlmm 13 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_STATUS; + }; + + led_status_red: led-2 { + gpios = <&tlmm 16 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_STATUS; + }; + + led-3 { + gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_WAN_ONLINE; + }; + + led-4 { + gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>; + color = ; + function = "router"; + }; + + led-5 { + gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_POWER; + default-state = "on"; + }; + + led-6 { + gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>; + color = ; + function = LED_FUNCTION_WAN; + }; + }; + + reserved-memory { + q6_mem_regions: q6_mem_regions@4b000000 { + no-map; + reg = <0x0 0x4b000000 0x0 0x3000000>; + }; + }; +}; + +&sleep_clk { + clock-frequency = <32000>; +}; + +&xo_board_clk { + clock-frequency = <24000000>; +}; + +&blsp1_uart1 { + status = "okay"; + + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; +}; + +&crypto { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&prng { + status = "okay"; +}; + +&qfprom { + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&qpic_nand { + pinctrl-0 = <&qpic_pins>; + pinctrl-names = "default"; + status = "okay"; + + flash@0 { + compatible = "spi-nand"; + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + + nand-ecc-engine = <&qpic_nand>; + + /* strength=8 breaks NAND I/O, use 4 instead */ + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + + partitions { + compatible = "qcom,smem-part"; + + partition-0-appsblenv { + compatible = "fixed-partitions"; + label = "0:appsblenv"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "env-data"; + reg = <0x0 0x40000>; + + nvmem-layout { + compatible = "u-boot,env"; + + macaddr_appsblenv_ethaddr: ethaddr { + compatible = "mac-base"; + #nvmem-cell-cells = <1>; + }; + }; + }; + }; + }; + }; +}; + +&switch { + status = "okay"; + + switch_mac_mode = ; + + qcom,port_phyinfo { + port@0 { + port_id = <1>; + mdiobus = <&mdio0>; + phy_address = <7>; + }; + + port@1 { + port_id = <2>; + forced-speed = <1000>; + forced-duplex = <1>; + }; + }; +}; + +&dp1 { + status = "okay"; + + label = "wan"; + nvmem-cells = <&macaddr_appsblenv_ethaddr 2>; + nvmem-cell-names = "mac-address"; +}; + +&dp2 { + status = "okay"; + + nvmem-cells = <&macaddr_appsblenv_ethaddr 0>; + nvmem-cell-names = "mac-address"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&mdio0 { + status = "okay"; +}; + +&mdio1 { + status = "okay"; + + pinctrl-0 = <&mdio1_pins>, <&switch_reset_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 39 GPIO_ACTIVE_LOW>; + + qca8337_0: ethernet-phy@0 { + reg = <0>; + }; + + qca8337_1: ethernet-phy@1 { + reg = <1>; + }; + + qca8337_2: ethernet-phy@2 { + reg = <2>; + }; + + qca8337_3: ethernet-phy@3 { + reg = <3>; + }; + + ethernet-switch@18 { + compatible = "qca,qca8337"; + reg = <0x18>; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&qca8337_0>; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&qca8337_1>; + }; + + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&qca8337_2>; + }; + + port@4 { + reg = <4>; + label = "lan4"; + phy-handle = <&qca8337_3>; + }; + + port@6 { + reg = <6>; + phy-mode = "sgmii"; + ethernet = <&dp2>; + qca,sgmii-enable-pll; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; +}; + +&tlmm { + button_pins: button-state { + key-pullup-pins { + pins = "gpio22", "gpio23", "gpio38"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + + key-pulldown-pins { + pins = "gpio31", "gpio32"; + function = "gpio"; + drive-strength = <8>; + bias-pull-down; + }; + }; + + led_pins: led-state { + pins = "gpio12", "gpio13", "gpio16", "gpio24", + "gpio25", "gpio26", "gpio28"; + function = "gpio"; + drive-strength = <8>; + bias-pull-down; + }; + + mdio1_pins: mdio-state { + mdc-pins { + pins = "gpio36"; + function = "mdc"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio-pins { + pins = "gpio37"; + function = "mdio"; + drive-strength = <8>; + bias-pull-up; + }; + }; + + qpic_pins: qpic-state { + clock-pins { + pins = "gpio9"; + function = "qspi_clk"; + drive-strength = <8>; + bias-disable; + }; + + cs-pins { + pins = "gpio8"; + function = "qspi_cs"; + drive-strength = <8>; + bias-disable; + }; + + data-pins { + pins = "gpio4", "gpio5", "gpio6", "gpio7"; + function = "qspi_data"; + drive-strength = <8>; + bias-disable; + }; + }; + + serial_0_pins: uart0-state { + pins = "gpio20", "gpio21"; + function = "blsp0_uart0"; + bias-disable; + }; + + switch_reset_pins: switch-reset-state { + pins = "gpio39"; + function = "gpio"; + drive-strength = <8>; + bias-pull-down; + }; +}; + +&tsens { + status = "okay"; +}; + +&q6v5_wcss { + status = "okay"; + + memory-region = <&q6_mem_regions>; + firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt", + "ath11k/IPQ5018/hw1.0/m3_fw.mdt", + "ath11k/QCN6122/hw1.0/m3_fw.mdt"; + + boot-args = <0x2 4 2 18 0 0>; /* pcie:1, len:4, updid:2, reset:gpio18 */ + + q6_wcss_pd1: pd-1 { + firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt"; + + resets = + <&gcc GCC_WCSSAON_RESET>, + <&gcc GCC_WCSS_BCR>, + <&gcc GCC_CE_BCR>; + reset-names = + "wcss_aon_reset", + "wcss_reset", + "ce_reset"; + + clocks = + <&gcc GCC_WCSS_AHB_S_CLK>, + <&gcc GCC_WCSS_ACMT_CLK>, + <&gcc GCC_WCSS_AXI_M_CLK>; + clock-names = + "gcc_wcss_ahb_s_clk", + "gcc_wcss_acmt_clk", + "gcc_wcss_axi_m_clk"; + + interrupts-extended = + <&wcss_smp2p_in 8 IRQ_TYPE_NONE>, + <&wcss_smp2p_in 9 IRQ_TYPE_NONE>, + <&wcss_smp2p_in 12 IRQ_TYPE_NONE>, + <&wcss_smp2p_in 11 IRQ_TYPE_NONE>; + interrupt-names = + "fatal", + "ready", + "spawn-ack", + "stop-ack"; + + qcom,smem-states = + <&wcss_smp2p_out 8>, + <&wcss_smp2p_out 9>, + <&wcss_smp2p_out 10>; + qcom,smem-state-names = + "shutdown", + "stop", + "spawn"; + }; + + q6_wcss_pd2: pd-2 { + firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt"; + + interrupts-extended = + <&wcss_smp2p_in 16 IRQ_TYPE_NONE>, + <&wcss_smp2p_in 17 IRQ_TYPE_NONE>, + <&wcss_smp2p_in 20 IRQ_TYPE_NONE>, + <&wcss_smp2p_in 19 IRQ_TYPE_NONE>; + interrupt-names = + "fatal", + "ready", + "spawn-ack", + "stop-ack"; + + qcom,smem-states = + <&wcss_smp2p_out 16>, + <&wcss_smp2p_out 17>, + <&wcss_smp2p_out 18>; + qcom,smem-state-names = + "shutdown", + "stop", + "spawn"; + }; +}; + +&wifi0 { + status = "okay"; + + qcom,rproc = <&q6_wcss_pd1>; + qcom,ath11k-calibration-variant = "IODATA-WN-DAX3000GR"; + qcom,ath11k-fw-memory-mode = <2>; + qcom,bdf-addr = <0x4c400000>; + + ieee80211-freq-limit = <2400000 2483000>; +}; + +&wifi1 { + status = "okay"; + + qcom,rproc = <&q6_wcss_pd2>; + qcom,userpd-subsys-name = "q6v5_wcss_userpd2"; + qcom,ath11k-calibration-variant = "IODATA-WN-DAX3000GR"; + qcom,ath11k-fw-memory-mode = <2>; + qcom,bdf-addr = <0x4d100000>; + qcom,m3-dump-addr = <0x4df00000>; + + ieee80211-freq-limit = <5150000 5730000>; +}; diff --git a/target/linux/qualcommax/image/ipq50xx.mk b/target/linux/qualcommax/image/ipq50xx.mk index 3ea222c9845..a15039e728a 100644 --- a/target/linux/qualcommax/image/ipq50xx.mk +++ b/target/linux/qualcommax/image/ipq50xx.mk @@ -57,6 +57,24 @@ define Device/glinet_gl-b3000 endef TARGET_DEVICES += glinet_gl-b3000 +define Device/iodata_wn-dax3000gr + $(call Device/FitImageLzma) + DEVICE_VENDOR := I-O DATA + DEVICE_MODEL := WN-DAX3000GR + DEVICE_DTS_CONFIG := config@mp03.3 + SOC := ipq5018 + KERNEL_IN_UBI := 1 + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 52480k + NAND_SIZE := 128m + IMAGES += factory.bin + IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand | \ + mstc-header 4.04(XZH.1)b90 0x480 + DEVICE_PACKAGES := ath11k-firmware-qcn6122 ipq-wifi-iodata_wn-dax3000gr +endef +TARGET_DEVICES += iodata_wn-dax3000gr + define Device/linksys_ipq50xx_mx_base $(call Device/FitImageLzma) DEVICE_VENDOR := Linksys diff --git a/target/linux/qualcommax/ipq50xx/base-files/etc/board.d/01_leds b/target/linux/qualcommax/ipq50xx/base-files/etc/board.d/01_leds index c12c61d61c1..89c6dc27f24 100644 --- a/target/linux/qualcommax/ipq50xx/base-files/etc/board.d/01_leds +++ b/target/linux/qualcommax/ipq50xx/base-files/etc/board.d/01_leds @@ -9,7 +9,8 @@ board_config_update board=$(board_name) case "$board" in -elecom,wrc-x3000gs2) +elecom,wrc-x3000gs2|\ +iodata,wn-dax3000gr) ucidef_set_led_netdev "wan" "WAN" "green:wan" "wan" "tx rx link_10 link_100 link_1000" ;; linksys,mr5500) diff --git a/target/linux/qualcommax/ipq50xx/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq50xx/base-files/etc/board.d/02_network index fb942af6cee..05b73e4d807 100644 --- a/target/linux/qualcommax/ipq50xx/base-files/etc/board.d/02_network +++ b/target/linux/qualcommax/ipq50xx/base-files/etc/board.d/02_network @@ -8,6 +8,7 @@ ipq50xx_setup_interfaces() local board="$1" case $board in elecom,wrc-x3000gs2|\ + iodata,wn-dax3000gr|\ linksys,mr5500) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan" ;; diff --git a/target/linux/qualcommax/ipq50xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/qualcommax/ipq50xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata index 894813f9d6a..f0d356956fb 100644 --- a/target/linux/qualcommax/ipq50xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata +++ b/target/linux/qualcommax/ipq50xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata @@ -9,7 +9,8 @@ board=$(board_name) case "$FIRMWARE" in "ath11k/IPQ5018/hw1.0/cal-ahb-c000000.wifi.bin") case "$board" in - elecom,wrc-x3000gs2) + elecom,wrc-x3000gs2|\ + iodata,wn-dax3000gr) caldata_extract "0:art" 0x1000 0x20000 wlan_mac=$(mtd_get_mac_ascii 0:appsblenv wifi0) ath11k_patch_mac $wlan_mac 0 @@ -34,7 +35,8 @@ case "$FIRMWARE" in ;; "ath11k/QCN6122/hw1.0/cal-ahb-b00a040.wifi1.bin") case "$board" in - elecom,wrc-x3000gs2) + elecom,wrc-x3000gs2|\ + iodata,wn-dax3000gr) caldata_extract "0:art" 0x26800 0x20000 wlan_mac=$(mtd_get_mac_ascii 0:appsblenv wifi1) ath11k_patch_mac $wlan_mac 0 diff --git a/target/linux/qualcommax/ipq50xx/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq50xx/base-files/lib/upgrade/platform.sh index 0f6ae73cc6b..760bc209276 100644 --- a/target/linux/qualcommax/ipq50xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/qualcommax/ipq50xx/base-files/lib/upgrade/platform.sh @@ -71,8 +71,9 @@ platform_check_image() { platform_do_upgrade() { case "$(board_name)" in - elecom,wrc-x3000gs2) - local delay index + elecom,wrc-x3000gs2|\ + iodata,wn-dax3000gr) + local delay delay=$(fw_printenv bootdelay) [ -z "$delay" ] || [ "$delay" -eq "0" ] && \ @@ -80,6 +81,7 @@ platform_do_upgrade() { elecom_upgrade_prepare + remove_oem_ubi_volume bt_fw remove_oem_ubi_volume ubi_rootfs remove_oem_ubi_volume wifi_fw nand_do_upgrade "$1"