From: Jörg Seitz Date: Sun, 21 Dec 2025 10:55:34 +0000 (+0100) Subject: mediatek: add support for device zbt-z8103ax-c X-Git-Url: http://git.ipfire.org/cgi-bin/gitweb.cgi?a=commitdiff_plain;h=refs%2Fpull%2F19823%2Fhead;p=thirdparty%2Fopenwrt.git mediatek: add support for device zbt-z8103ax-c - adopted MTD partition size increase from 64M to 128M -> this allows boot to complete - moved MAC addressing stuff out of partition definitions - all MAC addressing stuff is in .dtsi Specifications: SoC: MediaTek MT7981B RAM: 256MiB Flash: Winbond SPI-NAND 128 MiB Switch: 1 WAN, 3 LAN (Gigabit) MediaTek MT7531 Buttons: Reset, Mesh Power: DC 12V 1A WiFi: MT7981B 2.4Ghz & 5.8Ghz Led Layout from bottom to top: Power Mesh (RGB Led, user controllable, default set to OpenWrt Status) WLAN 2 GHz (user controllable) WAN (user controllable) LAN3 LAN2 LAN1 WLAN 5 GHz (Not on front panel but blinks through enclosure, user controllable) Buttons: Reset Mesh (user controllable, no default function) Installation: A. Through U-Boot menu: - Prepare your connecting computer to use a static IP in network 192.168.1.0/24 - Power down the router and hold in the Reset button. - While holding in the button power up the router again. - Hold the button in for 10 seconds and then release. - Use your browser to go to 192.168.1.1 - If you see a GUI allowing for flashing firmware then you got the right model. - Upload the sysupgrade file. Note: Recovery GUI can be used to recover from an incorrect firmware flash. B. Through OpenWrt Dashboard: If your router comes with OpenWrt preinstalled (modified by the seller), you can easily upgrade by going to the dashboard (192.168.1.1) and then navigate to System -> Backup/Flash firmware, then flash the firmware MAC Addresses were found in Factory partition: offset 0x4 F8:5E:3C:xx:xx:aa --> Router Label -2 offset 0xa F8:5E:3C:xx:xx:bb --> Router Label -1 offset 0x24 F8:5E:3C:xx:xx:cc --> Router Label +1 offset 0x2a F8:5E:3C:xx:xx:yy --> printed on Router Label Signed-off-by: Jörg Seitz Link: https://github.com/openwrt/openwrt/pull/19823 Signed-off-by: Hauke Mehrtens --- diff --git a/target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8103ax-c.dts b/target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8103ax-c.dts new file mode 100644 index 00000000000..1780b8c1c81 --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8103ax-c.dts @@ -0,0 +1,10 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; + +#include "mt7981b-zbtlink-zbt-z8103ax.dtsi" + +/ { + model = "Zbtlink 3000M(WiFi6) ZBT-Z8103AX-C"; + compatible = "zbtlink,zbt-z8103ax-c", "mediatek,mt7981b"; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index b7aef8f43a6..bfa00d1b44e 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -306,7 +306,8 @@ xiaomi,redmi-router-ax6000-stock|\ xiaomi,redmi-router-ax6000-ubootmod) ucidef_set_led_netdev "wan" "wan" "rgb:network" "wan" ;; -zbtlink,zbt-z8103ax) +zbtlink,zbt-z8103ax|\ +zbtlink,zbt-z8103ax-c) ucidef_set_led_netdev "wan" "wan" "green:wan" "eth1" "link tx rx" ;; zyxel,ex5601-t0-stock|\ diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index c69bd3abcb8..2519c97b9f8 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -19,7 +19,8 @@ mediatek_setup_interfaces() nokia,ea0326gmp|\ mercusys,mr80x-v3|\ routerich,ax3000-v1|\ - zbtlink,zbt-z8103ax) + zbtlink,zbt-z8103ax|\ + zbtlink,zbt-z8103ax-c) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" eth1 ;; acelink,ew-7886cax) diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 86e3e095b1e..dbec1c55784 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -3074,6 +3074,23 @@ define Device/zbtlink_zbt-z8103ax endef TARGET_DEVICES += zbtlink_zbt-z8103ax +define Device/zbtlink_zbt-z8103ax-c + DEVICE_VENDOR := Zbtlink + DEVICE_MODEL := ZBT-Z8103AX-C + DEVICE_DTS := mt7981b-zbtlink-zbt-z8103ax-c + DEVICE_DTS_DIR := ../dts + DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware + KERNEL_IN_UBI := 1 + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 65536k + IMAGES += factory.bin + IMAGE/factory.bin := append-ubi | check-size $$(IMAGE_SIZE) + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += zbtlink_zbt-z8103ax-c + define Device/zyxel_ex5601-t0-stock DEVICE_VENDOR := Zyxel DEVICE_MODEL := EX5601-T0