Commit 91f205acaf2a44ae75418d2f2cb156149f0df8ae extended the workaround
to cover vdso-o32.so.dbg but missed the vdso-n32.so.dbg which is added
now by this change.
ramips: Don't use a VLAN for the single ethernet port of the A5-V11.
This router only has one ethernet port, so a VLAN is useless here, now that the rt3050 TCP bug that happened without VLANs has been fixed for a very long time.
Add this router to the VLAN-less config that is used by other single-port routers.
Also fix MAC address detection code since this router has no WAN port.
blogic [Mon, 2 May 2016 18:51:05 +0000 (18:51 +0000)]
ramips: Get rt3050 ethernet ports to be disabled from the device tree.
This patch allows configuring ports to be disabled in the device tree; this
saves power, since disabling ports here actually disables power to ethernet
PHYs.
Line 444 enables all ethernet ports, so line 487 is getting zero ports to be
disabled, except for port 5 in SoCs where this is not implemented as it will
be sticky disabled in register POC0. Because of this, the code will still read
the switch configuration and OR it to the device tree setting.
blogic [Mon, 2 May 2016 18:51:01 +0000 (18:51 +0000)]
ramips: Fix comment in rt3050 ethernet switch driver.
Line 444 is actually enabling all switch ports by setting the disable bits
to 0. This needs to be done because the bootloader sets all ports to disabled
by default (which is the case for at least one router based on RT5350).
blogic [Mon, 2 May 2016 18:50:52 +0000 (18:50 +0000)]
ramips: Fix multicast ICMPv6 for the rt3050 ethernet switch.
The FCT2 esw register should be set to 0x2500C to have "unknown IPv6
multicast" packets broadcasted to every port, instead of dropped.
The previous value only let those packets go through ports 1 and 3.
"Unknown IPv6 multicast" packets include packets needed by ICMPv6 echo
requests addressed to well-known addresses, such as ff02::1 (MAC address
is 33:33:00:00:00:01 in this case).
Please note that by default ICMPv6 echo requests to ff02::1 are not replied
to by the router because of ip6tables considering those packets to be invalid.
But this is another bug/patch. ;)
blogic [Mon, 2 May 2016 18:50:35 +0000 (18:50 +0000)]
lantiq: VGV7510KW22BRN - set the phy clock source
VGV7510KW2 with VRX288 v1.2 has brnboot 1.8 installed. Starting with
this brnboot version, the "GPHY Clock Source" isn't set anymore by
brnboot, with the result that xrx200-net fails to probe/initialize the
phys.
Use the phy clock source device tree binding to specify the clock source.
blogic [Mon, 2 May 2016 18:50:23 +0000 (18:50 +0000)]
lantiq: handle the dual-firmware layout of brnboot
brnboot based devices can have two Image partitions. When flashing
images via the brnboot recovery web interface, the Image partitions are
written alternating.
The current active Image partition is stored in the first byte of the
Primary_Setting partition by using 0x00 for Code_Image_0 and 0x01 for
Code_Image_1.
By using the information about the active "Code Image", it is possible
to ensure that the rootfs belongs to the current booted Image/Kernel.
blogic [Mon, 2 May 2016 18:50:18 +0000 (18:50 +0000)]
lantiq: move partitions into partion table node
Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.
lantiq: use the same functionality for all ethernet phys led
The VGV7510KW22 has the leds for LAN1-3 connected to pin1 of the phys
and the led for LAN4 connect to pin0 of the phy. This results with the
current configuration in a fast flashing LAN4 led as soon as a network
cable is connected. Something similar was reported on the forum[1] for
the VGV7519 as well.
Since it isn't predicable to which pin a (single) phy led is connected,
use the (default) pin1 functionality
After checking pictures of all vr9 boards, it looks like only the VG3503J
has more than one led connected per phy. Using the phy led device tree
bindings to assign the functionality to the "additional" leds, the
VG3503J phy leds should behave as before.
add support for Planex MZK-EX750NP.
MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.
Rafał Miłecki [Fri, 6 May 2016 12:37:05 +0000 (14:37 +0200)]
mtd: add -c option for specifying amount of data to be used for checksum
So far fixtrx was calculating checksum over amount of data matching
partition erase size. It was mostly a workaround of checksum problem
after changing anything in initial TRX content (e.g. formatting JFFS2).
Its main purpose was to make bootloader accept modified TRX. This didn't
provide much protection of flash data against corruption.
This new option lets caller request calculating checksum over a bigger
amount of data. It may be used e.g. to include whole kernel data for
checksum and hopefully make bootloader go info failsafe mode if
something goes wrong.
Rafał Miłecki [Mon, 9 May 2016 17:00:53 +0000 (19:00 +0200)]
mtd: trx: use separated buffer for TRX header
We plan to adjust usage of the main buffer to allow reading custom
amount of data for CRC32. This means we need another buffer that will be
always block aligned.
rmilecki [Mon, 9 May 2016 12:53:39 +0000 (12:53 +0000)]
mtd: seama: fix image data handling
1) Put sanity checks in one place
2) Respect provided offset
3) Read only as much data as needed for MD5 calculation
Thanks to the last change this is a great speedup and memory saver. On
devices with NAND flash we were allocating & reading about 128 MiB while
something about 8 MiB is enough.
gdate.c: In function ‘g_date_strftime’:
gdate.c:2497:7: error: format not a string literal, format string not checked [-Werror=format-nonliteral]
tmplen = strftime (tmpbuf, tmpbufsize, locale_format, &tm);
^~~~~~
Daniel Golle [Fri, 29 Apr 2016 11:34:44 +0000 (11:34 +0000)]
base-files: evaluate uci-defaults on run-time installations
Packages may install scripts into /etc/uci-defaults to be executed once
after installation, usually at the first boot of the target. This works
fine if the package was installed to the rootfs during build or using
the ImageBuilder.
If the package is installed using opkg during run-time uci-defaults
were applied only after a reboot of the device. Avoid the need to
reboot by evaluting the package's uci-defaults in default-postinst.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Michal Hrusecky [Wed, 4 May 2016 11:53:27 +0000 (13:53 +0200)]
openssl: Update to version 1.0.2h
Bump to the latest version, fixes several security issues:
* CVE-2016-2107, CVE-2016-2105, CVE-2016-2106, CVE-2016-2109, CVE-2016-2176
More details at https://www.openssl.org/news/openssl-1.0.2-notes.html
Signed-off-by: Michal Hrusecky <Michal.Hrusecky@nic.cz>
Hans Dedecker [Mon, 2 May 2016 09:57:59 +0000 (11:57 +0200)]
xtables-addons: Avoid redefinition of SHRT_MAX in lua packet script
Patch Lua packet script defines SHRT_MAX which is already defined in <linux/kernel.h> and
is included indirectly by lauxlib.h. Fix the redefintion as it leads to compile failure
on systems which treat macro redefinition as an error
signing: remove unatteded build key and use current keyring instead
Remove the public unatteded buildkey from the opkg package to avoid
having hardcoded keys in tree. Use the external keyring package instead
which can be easily updated by users.
projects / thirdparty / openwrt.git / log
