Currently, a RCG's M/N counter (used for fraction division) is
set to either 'bypass' (counter disabled) or 'dual edge' (counter
enabled) based on whether the corresponding rcg struct has a mnd
field specified and a non-zero N.
In the case where M and N are the same value, the M/N counter is
still enabled by code even though no division takes place.
Leaving the RCG in such a state can result in improper behavior.
This was observed with the DSI pixel clock RCG when M and N were
both set to 1.
Add an additional check (M != N) to enable the M/N counter only
when it's needed for fraction division.
Signed-off-by: Archit Taneja <architt@codeaurora.org> Fixes: bcd61c0f535a (clk: qcom: Add support for root clock
generators (RCGs)) Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ahbix clock can never be turned off in practice. To change the
rates we need to switch the mux off the M/N counter to an always on
source (XO), reprogram the M/N counter to get the rate we want and
finally switch back to the M/N counter. Add a new ops structure
for this type of clock so that we can set the rate properly.
Fixes: 24d8fba44af3 "clk: qcom: Add support for IPQ8064's global
clock controller (GCC)"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Reviewed-by: Andy Gross <agross@codeaurora.org> Tested-by: Andy Gross <agross@codeaurora.org> Signed-off-by: Michael Turquette <mturquette@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current parent, plld_out0, does not exist. The proper name is
pll_d_out0. While at it, rename the plld_dsi clock to pll_d_dsi_out to
be more consistent with other clock names.
The number of resets controls is 32 times the number of peripheral
register banks rather than 32 times the number of clocks. This reduces
(drastically) the number of reset controls registered from 10080 (315
clocks * 32) to 224 (6 peripheral register banks * 32).
This also fixes a potential crash because trying to use any of the
excess reset controls (224-10079) would have caused accesses beyond
the array bounds of the peripheral register banks definition array.
Cc: Peter De Schrijver <pdeschrijver@nvidia.com> Cc: Prashant Gaikwad <pgaikwad@nvidia.com> Fixes: 6d5b988e7dc5 ("clk: tegra: implement a reset driver") Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 42773b28e71d ("clk: samsung: exynos4: Enable ARMCLK
down feature") enabled ARMCLK down feature on all Exynos4
SoCs. Unfortunately on Exynos4210 SoC ARMCLK down feature
causes a lockup when ondemand cpufreq governor is used.
Fix it by limiting ARMCLK down feature to Exynos4x12 SoCs.
This patch was tested on:
- Exynos4210 SoC based Trats board
- Exynos4210 SoC based Origen board
- Exynos4412 SoC based Trats2 board
- Exynos4412 SoC based Odroid-U3 board
Cc: Daniel Drake <drake@endlessm.com> Cc: Tomasz Figa <t.figa@samsung.com> Cc: Kukjin Kim <kgene@kernel.org> Fixes: 42773b28e71d ("clk: samsung: exynos4: Enable ARMCLK down feature") Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Michael Turquette <mturquette@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Level IRQ handlers and edge IRQ handler are managed by tow different
sets of registers. But currently the driver uses the same mask for the
both registers. It lead to issues with the following scenario:
First, an IRQ is requested on a GPIO to be triggered on front. After,
this an other IRQ is requested for a GPIO of the same bank but
triggered on level. Then the first one will be also setup to be
triggered on level. It leads to an interrupt storm.
The different kind of handler are already associated with two
different irq chip type. With this patch the driver uses a private
mask for each one which solves this issue.
It has been tested on an Armada XP based board and on an Armada 375
board. For the both boards, with this patch is applied, there is no
such interrupt storm when running the previous scenario.
This bug was already fixed but in a different way in the legacy
version of this driver by Evgeniy Dushistov: 9ece8839b1277fb9128ff6833411614ab6c88d68 "ARM: orion: Fix for certain
sequence of request_irq can cause irq storm". The fact the new version
of the gpio drive could be affected had been discussed there:
http://thread.gmane.org/gmane.linux.ports.arm.kernel/344670/focus=364012
- don't lock lp->lock in the iss_net_timer for the call of iss_net_poll,
it will lock it itself;
- invert order of lp->lock and opened_lock acquisition in the
iss_net_open to make it consistent with iss_net_poll;
- replace spin_lock with spin_lock_bh when acquiring locks used in
iss_net_timer from non-atomic context;
- replace spin_lock_irqsave with spin_lock_bh in the iss_net_start_xmit
as the driver doesn't use lp->lock in the hard IRQ context;
- replace __SPIN_LOCK_UNLOCKED(lp.lock) with spin_lock_init, otherwise
lockdep is unhappy about using non-static key.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xtensa actually uses sync_file_range2 implementation, so it should
define __NR_sync_file_range2 as other architectures that use that
function. That fixes userspace interface (that apparently never worked)
and avoids special-casing xtensa in libc implementations.
See the thread ending at
http://lists.busybox.net/pipermail/uclibc/2015-February/048833.html
for more details.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LCD driver is always built for the XTFPGA platform, but its base address
is not configurable, and is wrong for ML605/KC705. Its initialization
locks up KC705 board hardware.
Make the whole driver optional, and its base address and bus width
configurable. Implement 4-bit bus access method.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
acpi_scan_is_offline() may be called under the physical_node_lock
lock of the given device object's parent, so prevent lockdep from
complaining about that by annotating that instance with
SINGLE_DEPTH_NESTING.
Fixes: caa73ea158de (ACPI / hotplug / driver core: Handle containers in a special way) Reported-and-tested-by: Xie XiuQi <xiexiuqi@huawei.com> Reviewed-by: Toshi Kani <toshi.kani@hp.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is reported that ACPI interrupts do not work any more on
Dell Latitude D600 after commit c50f13c672df (ACPICA: Save
current masks of enabled GPEs after enable register writes).
The problem turns out to be related to the fact that the
enable_mask and enable_for_run GPE bit masks are not in
sync (in the absence of any system suspend/resume events)
for at least one GPE register on that machine.
Address this problem by writing the enable_for_run mask into
enable_mask as soon as enable_for_run is updated instead of
doing that only after the subsequent register write has
succeeded. For consistency, update acpi_hw_gpe_enable_write()
to store the bit mask to be written into the GPE register
in enable_mask unconditionally before the write.
Since the ACPI_GPE_SAVE_MASK flag is not necessary any more after
that, drop it along with the symbols depending on it.
Reported-and-tested-by: Jim Bos <jim876@xs4all.nl> Fixes: c50f13c672df (ACPICA: Save current masks of enabled GPEs after enable register writes) Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI_MTX_TABLES is acquired and released by the callers of
acpi_tb_install_standard_table() so releasing it in the function itself is
causing the following error in Linux kernel if the table is reloaded:
ACPI Error: Mutex [0x2] is not acquired, cannot release (20141107/utmutex-321)
Call Trace:
[<ffffffff81b0bd48>] dump_stack+0x4f/0x7b
[<ffffffff81546bf5>] acpi_ut_release_mutex+0x47/0x67
[<ffffffff81544357>] acpi_load_table+0x73/0xcb
Link: https://github.com/acpica/acpica/commit/c70434d4 Signed-off-by: Octavian Purdila <octavian.purdila@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is reported that on a physically 64-bit addressed machine, 32-bit kernel
can trigger crashes in accessing the memory regions that are beyond the
32-bit boundary. The region field's start address should still be 32-bit
compliant, but after a calculation (adding some offsets), it may exceed the
32-bit boundary. This case is rare and buggy, but there are real BIOSes
leaked with such issues (see References below).
This patch fixes this gap by always defining IO addresses as 64-bit, and
allows OSPMs to optimize it for a real 32-bit machine to reduce the size of
the internal objects.
Internal acpi_physical_address usages in the structures that can be fixed
by this change include:
1. struct acpi_object_region:
acpi_physical_address address;
2. struct acpi_address_range:
acpi_physical_address start_address;
acpi_physical_address end_address;
3. struct acpi_mem_space_context;
acpi_physical_address address;
4. struct acpi_table_desc
acpi_physical_address address;
See known issues 1 for other usages.
Note that acpi_io_address which is used for ACPI_PROCESSOR may also suffer
from same problem, so this patch changes it accordingly.
For iasl, it will enforce acpi_physical_address as 32-bit to generate
32-bit OSPM compatible tables on 32-bit platforms, we need to define
ACPI_32BIT_PHYSICAL_ADDRESS for it in acenv.h.
Known issues:
1. Cleanup of mapped virtual address
In struct acpi_mem_space_context, acpi_physical_address is used as a virtual
address:
acpi_physical_address mapped_physical_address;
It is better to introduce acpi_virtual_address or use acpi_size instead.
This patch doesn't make such a change. Because this should be done along
with a change to acpi_os_map_memory()/acpi_os_unmap_memory().
There should be no functional problem to leave this unchanged except
that only this structure is enlarged unexpectedly.
Link: https://github.com/acpica/acpica/commit/aacf863c
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=87971
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=79501 Reported-and-tested-by: Paul Menzel <paulepanter@users.sourceforge.net> Reported-and-tested-by: Sial Nije <sialnije@gmail.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If den=1 and pllin_rate>20MHz then den and num are adjusted to 0
causing a divide by zero error a few lines further on. Therefore
this patch correctly scales num and den such that
pllin_rate/den < 20MHz as required in the device data sheet.
Signed-off-by: Howard Mitchell <hm@hmbedded.co.uk> Signed-off-by: Mark Brown <broonie@sirena.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to ensure that 'alsactl restore' does not apply default
initialisation as the chip reset defaults are preferred.
Signed-off-by: Howard Mitchell <hm@hmbedded.co.uk> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WM8741 DAC supports the following typical audio sampling rates:
44.1kHz, 88.2kHz, 176.4kHz (eg: with a master clock of 22.5792MHz)
32kHz, 48kHz, 96kHz, 192kHz (eg: with a master clock of 24.576MHz)
For the rates lists, we should use 82000 instead of 88235, 176400
instead of 1764000 and 192000 instead of 19200 (seems to be a typo).
Signed-off-by: Sergej Sawazki <ce3a@gmx.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The delay time after a reset in the codec probe callback was too short,
and did not work on certain hw because the codec needs more time to
power on. This increases the delay time from 1us to 1ms.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com> Acked-by: Brian Austin <brian.austin@cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This problem appears to have been introduced in 2.6.29 by commit 93197a36a9c1 "Rewrite sysfs processor cache info code".
This caused lscpu to error out on at least e500v2 devices, eg:
error: cannot open /sys/devices/system/cpu/cpu0/cache/index2/size: No such file or directory
Some embedded powerpc systems use cache-size in DTS for the unified L2
cache size, not d-cache-size, so we need to allow for both DTS names.
Added a new CACHE_TYPE_UNIFIED_D cache_type_info structure to handle
this.
Fixes: 93197a36a9c1 ("powerpc: Rewrite sysfs processor cache info code") Signed-off-by: Dave Olson <olson@cumulusnetworks.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If M64 has been supported, the prefetchable 64-bits memory resources
shouldn't be mapped to the corresponding PE# via M32DT. Unfortunately,
we're doing that in pnv_ioda_setup_pe_seg() wrongly. The issue was
introduced by commit 262af55 ("powerpc/powernv: Enable M64 aperatus
for PHB3"). The patch fixes the issue by simply skipping M64 resources
when updating to M32DT.
When running a compat (AArch32) userspace on Cortex-A53, a load at EL0
from a virtual address that matches the bottom 32 bits of the virtual
address used by a recent load at (AArch64) EL1 might return incorrect
data.
This patch works around the issue by writing to the contextidr_el1
register on the exception return path when returning to a 32-bit task.
This workaround is patched in at runtime based on the MIDR value of the
processor.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Tested-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we only perform alternative patching for kernels built with
CONFIG_SMP, as we call apply_alternatives_all() in smp.c, which is only
built for CONFIG_SMP. Thus !SMP kernels may not have necessary
alternatives patched in.
This patch ensures that we call apply_alternatives_all() once all CPUs
are booted, even for !SMP kernels, by having the smp_init_cpus() stub
call this for !SMP kernels via up_late_init. A new wrapper,
do_post_cpus_up_work, is added so we can hook other calls here later
(e.g. boot mode logging).
Cc: Andre Przywara <andre.przywara@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Fixes: e039ee4ee3fcf174 ("arm64: add alternative runtime patching") Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After writing the page tables, we use __inval_cache_range to invalidate
any stale cache entries. Strongly Ordered memory accesses are not
ordered w.r.t. cache maintenance instructions, and hence explicit memory
barriers are required to provide this ordering. However,
__inval_cache_range was written to be used on Normal Cacheable memory
once the MMU and caches are on, and does not have any barriers prior to
the DC instructions.
This patch adds a DMB between the page tables being written and the
corresponding cachelines being invalidated, ensuring that the
invalidation makes the new data visible to subsequent cacheable
accesses. A barrier is not required before the prior invalidate as we do
not access the page table memory area prior to this, and earlier
barriers in preserve_boot_args and set_cpu_boot_mode_flag ensures
ordering w.r.t. any stores performed prior to entering Linux.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Fixes: c218bca74eeafa2f ("arm64: Relax the kernel cache requirements for boot") Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register MIDR_EL1 is masked to get variant and revision fields, then
compared against midr_range_min and midr_range_max when checking
whether CPU is affected by any particular erratum. However, variant
and revision fields in MIDR_EL1 are separated by 16 bits, so the min
and max of midr range should be constructed accordingly, otherwise
the patch will not be applied when variant field is non-0.
Acked-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Bo Yan <byan@nvidia.com>
[will: use MIDR_VARIANT_SHIFT to construct upper bound] Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 04f2:aff1 to ath3k.c supported devices list and btusb.c blacklist, so
that the device can load the ath3k firmware and re-enumerate itself as an
AR3011 device.
Before we reach to connection established we may get an
error event. In this case the core won't teardown this
connection (never established it), so we take care of freeing
it ourselves.
This hang was a result of a missing command put when
a DIF error occurred during a rdma read (and we sent
an CHECK_CONDITION error without passing it to the
backend).
In fd_do_prot_rw(), it allocates prot_buf which is used to copy from
se_cmd->t_prot_sg by sbc_dif_copy_prot(). The SG table for prot_buf
is also initialized by allocating 'se_cmd->t_prot_nents' entries of
scatterlist and setting the data length of each entry to PAGE_SIZE
at most.
However if se_cmd->t_prot_sg contains a clustered entry (i.e.
sg->length > PAGE_SIZE), the SG table for prot_buf can't be
initialized correctly and sbc_dif_copy_prot() can't copy to prot_buf.
(This actually happened with TCM loopback fabric module)
As prot_buf is allocated by kzalloc() and it's physically contiguous,
we only need a single scatterlist entry.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When UNMAP command is issued with DIF protection support enabled,
the protection info for the unmapped region is remain unchanged.
So READ command for the region causes data integrity failure.
This fixes it by invalidating protection info for the unmapped region
by filling with 0xff pattern. This change also adds helper function
fd_do_prot_fill() in order to reduce code duplication with existing
fd_format_prot().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Reviewed-by: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_DEBUG_SG=y and DIF protection support enabled, kernel
BUG()s are triggered due to the following two issues:
1) prot_sg is not initialized by sg_init_table().
When CONFIG_DEBUG_SG=y, scatterlist helpers check sg entry has a
correct magic value.
2) vmalloc'ed buffer is passed to sg_set_buf().
sg_set_buf() uses virt_to_page() to convert virtual address to struct
page, but it doesn't work with vmalloc address. vmalloc_to_page()
should be used instead. As prot_buf isn't usually too large, so
fix it by allocating prot_buf by kmalloc instead of vmalloc.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug for COMPARE_AND_WRITE handling with
fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC.
It adds the missing allocation for cmd->t_bidi_data_sg within
transport_generic_new_cmd() that is used by COMPARE_AND_WRITE
for the initial READ payload, even if the fabric is already
providing a pre-allocated buffer for cmd->t_data_sg.
Also, fix zero-length COMPARE_AND_WRITE handling within the
compare_and_write_callback() and target_complete_ok_work()
to queue the response, skipping the initial READ.
This fixes COMPARE_AND_WRITE emulation with loopback, vhost,
and xen-backend fabric drivers using SG_TO_MEM_NOALLOC.
Reported-by: Christoph Hellwig <hch@lst.de> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch converts iscsi-target code to use modern kthread.h API
callers for creating RX/TX threads for each new iscsi_conn descriptor,
and releasing associated RX/TX threads during connection shutdown.
This is done using iscsit_start_kthreads() -> kthread_run() to start
new kthreads from within iscsi_post_login_handler(), and invoking
kthread_stop() from existing iscsit_close_connection() code.
Also, convert iscsit_logout_post_handler_closesession() code to use
cmpxchg when determing when iscsit_cause_connection_reinstatement()
needs to sleep waiting for completion.
We may exit this function without properly freeing up the maapings
we may have acquired. Fix the bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Long Li <longli@microsoft.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comparison from the previous line seems to have been erroneously
(partially) copied-and-pasted onto the next. The second line should be
checking req.bytes, not req.lnum.
Coverity CID #139400
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[rw: Fixed comparison] Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some of the 'out_not_moved' error paths, lnum may be used
uninitialized. Don't ignore the warning; let's fix it.
This uninitialized variable doesn't have much visible effect in the end,
since we just schedule the PEB for erasure, and its LEB number doesn't
really matter (it just gets printed in debug messages). But let's get it
straight anyway.
Coverity CID #113449
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are completely discarding the earlier value of 'bitflips', which
could reflect a bitflip found in ubi_io_read_vid_hdr(). Let's use the
bitwise OR of header and data 'bitflip' statuses instead.
Since commit ee0778a30153
("tools/power: turbostat: make Makefile a bit more capable")
turbostat's Makefile is using
[...]
BUILD_OUTPUT := $(PWD)
[...]
which obviously causes trouble when building "turbostat" with
make -C /usr/src/linux/tools/power/x86/turbostat ARCH=x86 turbostat
because GNU make does not update nor guarantee that $PWD is set.
This patch changes the Makefile to use $CURDIR instead, which GNU make
guarantees to set and update (i.e. when using "make -C ...") and also
adds support for the O= option (see "make help" in your root of your
kernel source tree for more details).
Link: https://bugs.gentoo.org/show_bug.cgi?id=533918 Fixes: ee0778a30153 ("tools/power: turbostat: make Makefile a bit more capable") Signed-off-by: Thomas D. <whissi@whissi.de> Cc: Mark Asselstine <mark.asselstine@windriver.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a event PADDING is hit (a deleted event that is still in the ring
buffer), translate_data() sets the length of the padding and also updates
the data pointer which is passed back to the caller.
This is unneeded because the caller also updates the data pointer with
the passed back length. translate_data() should not update the pointer,
only set the length.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: http://lkml.kernel.org/r/20150324135923.461431960@goodmis.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes this build error with glibc < 2.6.
CC util/cloexec.o
cc1: warnings being treated as errors
util/cloexec.c: In function ‘perf_flag_probe’:
util/cloexec.c:24: error: implicit declaration of function
‘sched_getcpu’
util/cloexec.c:24: error: nested extern declaration of ‘sched_getcpu’
make: *** [util/cloexec.o] Error 1
Signed-off-by: Vinson Lee <vlee@twitter.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Yann Droneaud <ydroneaud@opteya.com> Link: http://lkml.kernel.org/r/1427137761-16119-1-git-send-email-vlee@twopensource.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
c6e5e9fbc3ea ("perf tools: Fix building error in x86_64 when dwarf unwind is on")
removed the definition of IS_X86_64 but not all places using it, with
the consequence that perf-read-vdsox32 would not be built anymore, and
the default lib install directory was 'lib' instead of 'lib64'.
The token STT_GNU_IFUNC is not available with glibc 2.9 and older.
Define this token if it is not already defined.
This patch fixes this build errors with older versions of glibc.
CC util/symbol-elf.o
util/symbol-elf.c: In function ‘elf_sym__is_function’:
util/symbol-elf.c:75: error: ‘STT_GNU_IFUNC’ undeclared (first use in this function)
util/symbol-elf.c:75: error: (Each undeclared identifier is reported only once
util/symbol-elf.c:75: error: for each function it appears in.)
make: *** [util/symbol-elf.o] Error 1
Signed-off-by: Vinson Lee <vlee@twitter.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Anton Blanchard <anton@samba.org> Cc: Avi Kivity <avi@cloudius-systems.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Stephane Eranian <eranian@google.com> Cc: Waiman Long <Waiman.Long@hp.com> Link: http://lkml.kernel.org/r/1423528286-13630-1-git-send-email-vlee@twopensource.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I started to work with PPI interface so that it would be available
under character device sysfs directory and realized that chip
registeration was still too messy.
In TPM 1.x in some rare scenarios (errors that almost never occur)
wrong order in deinitialization steps was taken in teardown. I
reproduced these scenarios by manually inserting error codes in the
place of the corresponding function calls.
The key problem is that the teardown is messy with two separate code
paths (this was inherited when moving code from tpm-interface.c).
Moved TPM 1.x specific register/unregister functionality to own helper
functions and added single code path for teardown in tpm_chip_register().
Now the code paths have been fixed and it should be easier to review
later on this part of the code.
Fixes: 7a1d7e6dd76a ("tpm: TPM 2.0 baseline support") Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Scot Doyle <lkml14@scotdoyle.com> Reviewed-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that it is possible to lazily unmount an entire mount tree and
leave the individual mounts connected to each other add a new flag
UMOUNT_CONNECTED to umount_tree to force this behavior and use
this flag in detach_mounts.
This closes a bug where the deletion of a file or directory could
trigger an unmount and reveal data under a mount point.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lookup_mountpoint can return either NULL or an error value.
Update the test in __detach_mounts to test for an error value
to avoid pathological cases causing a NULL pointer dereferences.
The callers of __detach_mounts should prevent it from ever being
called on an unlinked dentry but don't take any chances.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify umount(MNT_DETACH) to keep mounts in the hash table that are
locked to their parent mounts, when the parent is lazily unmounted.
In mntput_no_expire detach the children from the hash table, depending
on mnt_pin_kill in cleanup_mnt to decrement the mnt_count of the children.
In __detach_mounts if there are any mounts that have been unmounted
but still are on the list of mounts of a mountpoint, remove their
children from the mount hash table and those children to the unmounted
list so they won't linger potentially indefinitely waiting for their
final mntput, now that the mounts serve no purpose.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For future use factor out a function umount_mnt from umount_tree.
This function unhashes a mount and remembers where the mount
was mounted so that eventually when the code makes it to a
sleeping context the mountpoint can be dput.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create a function unhash_mnt that contains the common code between
detach_mnt and umount_tree, and use unhash_mnt in place of the common
code. This add a unncessary list_del_init(mnt->mnt_child) into
umount_tree but given that mnt_child is already empty this extra
line is a noop.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the first mount in shared subtree is locked don't unmount the
shared subtree.
This is ensured by walking through the mounts parents before children
and marking a mount as unmountable if it is not locked or it is locked
but it's parent is marked.
This allows recursive mount detach to propagate through a set of
mounts when unmounting them would not reveal what is under any locked
mount.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A prerequisite of calling umount_tree is that the point where the tree
is mounted at is valid to unmount.
If we are propagating the effect of the unmount clear MNT_LOCKED in
every instance where the same filesystem is mounted on the same
mountpoint in the mount tree, as we know (by virtue of the fact
that umount_tree was called) that it is safe to reveal what
is at that mountpoint.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Modify __lookup_mnt_hash_last to ignore mounts that have MNT_UMOUNTED set.
- Don't remove mounts from the mount hash table in propogate_umount
- Don't remove mounts from the mount hash table in umount_tree before
the entire list of mounts to be umounted is selected.
- Remove mounts from the mount hash table as the last thing that
happens in the case where a mount has a parent in umount_tree.
Mounts without parents are not hashed (by definition).
This paves the way for delaying removal from the mount hash table even
farther and fixing the MNT_LOCKED vs MNT_DETACH issue.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
umount_tree builds a list of mounts that need to be unmounted.
Utilize mnt_list for this purpose instead of mnt_hash. This begins to
allow keeping a mount on the mnt_hash after it is unmounted, which is
necessary for a properly functioning MNT_LOCKED implementation.
The fact that mnt_list is an ordinary list makding available list_move
is nice bonus.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Invoking mount propagation from __detach_mounts is inefficient and
wrong.
It is inefficient because __detach_mounts already walks the list of
mounts that where something needs to be done, and mount propagation
walks some subset of those mounts again.
It is actively wrong because if the dentry that is passed to
__detach_mounts is not part of the path to a mount that mount should
not be affected.
change_mnt_propagation(p,MS_PRIVATE) modifies the mount propagation
tree of a master mount so it's slaves are connected to another master
if possible. Which means even removing a mount from the middle of a
mount tree with __detach_mounts will not deprive any mount propagated
mount events.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Remove the unneeded declaration from pnode.h
- Mark umount_tree static as it has no callers outside of namespace.c
- Define an enumeration of umount_tree's flags.
- Pass umount_tree's flags in by name
This removes the magic numbers 0, 1 and 2 making the code a little
clearer and makes it possible for there to be lazy unmounts that don't
propagate. Which is what __detach_mounts actually wants for example.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously commit 14ece1028b3ed53ffec1b1213ffc6acaf79ad77c added a
support for for syncing parent directory of newly created inodes to
make sure that the inode is not lost after a power failure in
no-journal mode.
However this does not work in majority of cases, namely:
- if the directory has inline data
- if the directory is already indexed
- if the directory already has at least one block and:
- the new entry fits into it
- or we've successfully converted it to indexed
So in those cases we might lose the inode entirely even after fsync in
the no-journal mode. This also includes ext2 default mode obviously.
I've noticed this while running xfstest generic/321 and even though the
test should fail (we need to run fsck after a crash in no-journal mode)
I could not find a newly created entries even when if it was fsynced
before.
Fix this by adjusting the ext4_add_entry() successful exit paths to set
the inode EXT4_STATE_NEWENTRY so that fsync has the chance to fsync the
parent directory as well.
Signed-off-by: Lukas Czerner <lczerner@redhat.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Frank Mayhar <fmayhar@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marek Vasut <marex@denx.de> Tested-by: Marek Vasut <marex@denx.de> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: John W. Linville <linville@tuxdriver.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c_master_send may return many negative values different than
-EREMOTEIO.
In case an i2c transaction is NACK'ed, on raspberry pi B+
kernel 3.18, -EIO is generated instead.
We currently need two checks of the peripheral version in MACB_MID register.
One of them got out of sync after modification by 8a013a9c71b2 (net: macb:
Include multi queue support for xilinx ZynqMP ethernet version).
Fix this in macb_configure_caps() so that xilinx ZynqMP will be considered
as a GEM flavor.
Fixes: 8a013a9c71b2 ("net: macb: Include multi queue support for xilinx ZynqMP
ethernet version")
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Punnaiah Choudary Kalluri <punnaia@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some Silvermont-Core/Baytrail-SOC systems,
C1E latency is higher than original specifications.
Although C1E is still enumerated in CPUID.MWAIT.EDX,
we delete the state from intel_idle to avoid latency impact.
Under some conditions, the latency of the C6N-BYT and C6S-BYT states
may exceed the specified values of 40 and 140 usec, respectively.
Increase those values to 300 and 500 usec; to assure
that the hardware does not violate constraints that may be set
by the Linux PM_QOS sub-system.
Also increase the C7-BYT target residency to 4.0 ms from 1.5 ms.
Signed-off-by: Len Brown <len.brown@intel.com> Cc: Kumar P Mahesh <mahesh.kumar.p@intel.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ptrace_resume() is called when the tracee is still __TASK_TRACED. We set
tracee->exit_code and then wake_up_state() changes tracee->state. If the
tracer's sub-thread does wait() in between, task_stopped_code(ptrace => T)
wrongly looks like another report from tracee.
This confuses debugger, and since wait_task_stopped() clears ->exit_code
the tracee can miss a signal.
Note for stable: the bug is very old, but without 9899d11f6544 "ptrace:
ensure arch_ptrace/ptrace_request can never race with SIGKILL" the fix
should use lock_task_sighand(child).
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Reported-by: Pavel Labath <labath@google.com> Tested-by: Pavel Labath <labath@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE enabled, and a normal top-down
address allocation strategy, load_elf_binary() will attempt to map a PIE
binary into an address range immediately below mm->mmap_base.
Unfortunately, load_elf_ binary() does not take account of the need to
allocate sufficient space for the entire binary which means that, while
the first PT_LOAD segment is mapped below mm->mmap_base, the subsequent
PT_LOAD segment(s) end up being mapped above mm->mmap_base into the are
that is supposed to be the "gap" between the stack and the binary.
Since the size of the "gap" on x86_64 is only guaranteed to be 128MB this
means that binaries with large data segments > 128MB can end up mapping
part of their data segment over their stack resulting in corruption of the
stack (and the data segment once the binary starts to run).
Any PIE binary with a data segment > 128MB is vulnerable to this although
address randomization means that the actual gap between the stack and the
end of the binary is normally greater than 128MB. The larger the data
segment of the binary the higher the probability of failure.
Fix this by calculating the total size of the binary in the same way as
load_elf_interp().
Signed-off-by: Michael Davidson <md@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Kees Cook <keescook@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 6e3f62f0793e ("mfd: core: Fix platform-device id
generation") we honour PLATFORM_DEVID_AUTO and PLATFORM_DEVID_NONE when
registering mfd-devices.
Unfortunately, some mfd-drivers rely on the old behaviour of generating
platform-device ids by adding the cell id also to the special value of
PLATFORM_DEVID_NONE. The resulting platform ids are not only used to
generate device-unique names, but are also used instead of the cell id
to identify cells when probing subdevices.
These drivers should be updated to use PLATFORM_DEVID_AUTO, which would
also allow more than one device to be registered without resorting to
hacks (see for example wm831x), but lets fix the regression first by
partially reverting the above mentioned commit with respect to
PLATFORM_DEVID_NONE.
Fixes: 6e3f62f0793e ("mfd: core: Fix platform-device id generation") Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2) pointing stick packet is received, the hw will report a BTN_LEFT 1 in
this packet because when the trackstick is active it communicates the
combined touchpad + pointing stick buttons in the trackstick packet,
since alps_report_bare_ps2_packet passes NULL (*) for the dev2 parameter
to alps_report_buttons the combining is not detected and the
pointing stick evdev node will also report BTN_LEFT 1
3) on release of the button a pointing stick packet with BTN_LEFT 0 is
received and the pointing stick evdev node will report BTN_LEFT 0
Note how because of the passing as NULL for dev2 the touchpad evdev node
will never send BTN_LEFT 0 in this scenario leading to a stuck mouse button.
This is a regression in 4.0 introduced by commit 04aae283ba6a8
("Input: ALPS - do not mix trackstick and external PS/2 mouse data")
This commit fixes this by passing in the touchpad evdev as dev2 parameter
when calling alps_report_buttons for the pointingstick on alps v2 devices,
so that alps_report_buttons correctly detect that we're already reporting
the button as pressed via the touchpad evdev node, and will also send the
release event there.
Reported-by: Hans de Bruin <jmdebruin@xmsnet.nl> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On ASUS TP500LN and X750JN, the touchpad absolute mode is reset each
time set_rate is done.
In order to fix this, we will verify the firmware version, and if it
matches the one in those laptops, the set_rate function is overloaded
with a function elantech_set_rate_restore_reg_07 that performs the
set_rate with the original function, followed by a restore of reg_07
(the register that sets the absolute mode on elantech v4 hardware).
Also the ASUS TP500LN and X750JN firmware version, capabilities, and
button constellation is added to elantech.c
Reported-and-tested-by: George Moutsopoulos <gmoutso@yahoo.co.uk> Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions snd_emu10k1_proc_spdif_read and snd_emu1010_fpga_read
acquire the emu_lock before accessing the FPGA. The function used
to access the FPGA (snd_emu1010_fpga_read) also tries to take
the emu_lock which causes a deadlock.
Remove the outer locking in the proc-functions (guarding only the
already safe fpga read) to prevent this deadlock.
[removed superfluous flags variables too -- tiwai]
Adds Microsoft LifeCam Cinema USB ID to the snd_usb_get_sample_rate_quirk list as the Lifecam Cinema does not appear to support getting the sample rate.
Fixes the issue where the LifeCam Cinema would wait for USB timeout and log the message "cannot get freq at ep 0x82" when accessed.
The at91sam9n12 and at91sam9x5 usb clocks do not propagate rate
modification requests to their parents.
This causes a bug when the PLLB is left uninitialized by the bootloader
(PLL multiplier set to 0, or in other words, PLL rate = 0 Hz).
Implement the determinate_rate method and propagate the change rate
request to the parent clk.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reported-by: Bo Shen <voice.shen@atmel.com> Tested-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Michael Turquette <mturquette@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While this driver was already using a 50ms resume
timeout, let's make sure everybody uses the same
macro so it's easy to fix later should anything
go wrong.
It also gives a more "stable" expectation to Linux
users.
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every USB Host controller should use this new
macro to define for how long resume signalling
should be driven on the bus.
Currently, almost every single USB controller
is using a 20ms timeout for resume signalling.
That's problematic for two reasons:
a) sometimes that 20ms timer expires a little
before 20ms, which makes us fail certification
b) some (many) devices actually need more than
20ms resume signalling.
Sure, in case of (b) we can state that the device
is against the USB spec, but the fact is that
we have no control over which device the certification
lab will use. We also have no control over which host
they will use. Most likely they'll be using a Windows
PC which, again, we have no control over how that
USB stack is written and how long resume signalling
they are using.
At the end of the day, we must make sure Linux passes
electrical compliance when working as Host or as Device
and currently we don't pass compliance as host because
we're driving resume signallig for exactly 20ms and
that confuses certification test setup resulting in
Certification failure.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The res parameter passed to devm_usb_phy_match() is the location where the
pointer to the usb_phy is stored, hence it needs to be dereferenced before
comparing to the match data in order to find the correct match.
Fixes: 410219dcd2ba ("usb: otg: utils: devres: Add API's to associate a device with the phy") Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resolve a merge conflict with mmc refactoring aaa25a5a33cb ("ARM: dts:
unuse the slot-node and deprecate the supports-highspeed for dw-mmc in
exynos") by dropping the slot@0 nodes, moving its bus-width property to
the mmc node and replacing supports-highspeed with cap-{mmc,sd}-highspeed,
matching exynos5250-snow.
Cc: Jaehoon Chung <jh80.chung@samsung.com> Fixes: 53dd4138bb0a ("ARM: dts: Add exynos5250-spring device tree") Signed-off-by: Andreas Faerber <afaerber@suse.de> Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Kukjin Kim <kgene@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After 57a38effa598 (net: phy: micrel: disable broadcast for KSZ8081/KSZ8091)
the macb1 interface refuses to work properly because it tries
to cling to address 0 which isn't able to communicate in broadcast with
the mac anymore. The micrel phy on the board is actually configured
to show up at address 1.
Adding the phy node and its real address fixes the issue.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Johan Hovold <johan@kernel.org> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two PMICs on Cragganmore, currently one dynamically assign
its IRQ base and the other uses a fixed base. It is possible for the
statically assigned PMIC to fail if its IRQ is taken by the dynamically
assigned one. Fix this by statically assigning both the IRQ bases.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Kukjin Kim <kgene@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Armada 38x SoCs, under heavy I/O load, the system hangs when CPU
Idle is enabled. Waiting for a solution to this issue, this patch
disables the CPU Idle support for this SoC.
As CPU Hot plug support also uses some of the CPU Idle functions it is
also affected by the same issue. This patch disables it also for the
Armada 38x SoCs.
projects / thirdparty / kernel / stable.git / log
