We may exit this function without properly freeing up the maapings
we may have acquired. Fix the bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Long Li <longli@microsoft.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Fixes: 28d8909bc790 ("[XFRM]: Export SAD info.") Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Fixes: ecfd6b183780 ("[XFRM]: Export SPD info") Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
AF_RDS, PF_RDS and SOL_RDS are available in header files,
and there is no need to get their values from /proc. Document
this correctly.
Fixes: 0c5f9b8830aa ("RDS: Documentation") Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
On ASUS TP500LN and X750JN, the touchpad absolute mode is reset each
time set_rate is done.
In order to fix this, we will verify the firmware version, and if it
matches the one in those laptops, the set_rate function is overloaded
with a function elantech_set_rate_restore_reg_07 that performs the
set_rate with the original function, followed by a restore of reg_07
(the register that sets the absolute mode on elantech v4 hardware).
Also the ASUS TP500LN and X750JN firmware version, capabilities, and
button constellation is added to elantech.c
Reported-and-tested-by: George Moutsopoulos <gmoutso@yahoo.co.uk> Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Looking over the implementation for jhash2 and comparing it to jhash_3words
I realized that the two hashes were in fact very different. Doing a bit of
digging led me to "The new jhash implementation" in which lookup2 was
supposed to have been replaced with lookup3.
In reviewing the patch I noticed that jhash2 had originally initialized a
and b to JHASH_GOLDENRATIO and c to initval, but after the patch a, b, and
c were initialized to initval + (length << 2) + JHASH_INITVAL. However the
changes in jhash_3words simply replaced the initialization of a and b with
JHASH_INITVAL.
This change corrects what I believe was an oversight so that a, b, and c in
jhash_3words all have the same value added consisting of initval + (length
<< 2) + JHASH_INITVAL so that jhash2 and jhash_3words will now produce the
same hash result given the same inputs.
Fixes: 60d509c823cca ("The new jhash implementation") Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
Previously commit 14ece1028b3ed53ffec1b1213ffc6acaf79ad77c added a
support for for syncing parent directory of newly created inodes to
make sure that the inode is not lost after a power failure in
no-journal mode.
However this does not work in majority of cases, namely:
- if the directory has inline data
- if the directory is already indexed
- if the directory already has at least one block and:
- the new entry fits into it
- or we've successfully converted it to indexed
So in those cases we might lose the inode entirely even after fsync in
the no-journal mode. This also includes ext2 default mode obviously.
I've noticed this while running xfstest generic/321 and even though the
test should fail (we need to run fsck after a crash in no-journal mode)
I could not find a newly created entries even when if it was fsynced
before.
Fix this by adjusting the ext4_add_entry() successful exit paths to set
the inode EXT4_STATE_NEWENTRY so that fsync has the chance to fsync the
parent directory as well.
Signed-off-by: Lukas Czerner <lczerner@redhat.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Frank Mayhar <fmayhar@google.com>
[lizf: Backported to 3.4: remove a change from return to goto, as that
doesn't exist in 3.4] Signed-off-by: Zefan Li <lizefan@huawei.com>
The delay time after a reset in the codec probe callback was too short,
and did not work on certain hw because the codec needs more time to
power on. This increases the delay time from 1us to 1ms.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com> Acked-by: Brian Austin <brian.austin@cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Usually ELF_ET_DYN_BASE is 2/3 of TASK_SIZE. With 3G/1G user/kernel
split this is not so, because 2*TASK_SIZE overflows 32 bits,
so the actual value of ELF_ET_DYN_BASE is:
(2 * TASK_SIZE / 3) = 0x2a000000
When ASLR is disabled PIE binaries will load at ELF_ET_DYN_BASE address.
On 32bit platforms AddressSanitzer uses addresses [0x20000000 - 0x40000000]
for shadow memory [1]. So ASan doesn't work for PIE binaries when ASLR disabled
as it fails to map shadow memory.
Also after Kees's 'split ET_DYN ASLR from mmap ASLR' patchset PIE binaries
has a high chance of loading somewhere in between [0x2a000000 - 0x40000000]
even if ASLR enabled. This makes ASan with PIE absolutely incompatible.
Fix overflow by dividing TASK_SIZE prior to multiplying.
After this patch ELF_ET_DYN_BASE equals to (for CONFIG_VMSPLIT_3G=y):
(TASK_SIZE / 3 * 2) = 0x7f555554
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Reported-by: Maria Guseva <m.guseva@samsung.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
ie. the missing attribute name after the namespace.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94291 Reported-by: William Douglas <william.douglas@intel.com> Signed-off-by: David Sterba <dsterba@suse.cz> Signed-off-by: Chris Mason <clm@fb.com>
[lizf: Backported to 3.4:
- 3.4 doesn't support XATTR_BTRFS_PREFIX] Signed-off-by: Zefan Li <lizefan@huawei.com>
While committing a transaction we free the log roots before we write the
new super block. Freeing the log roots implies marking the disk location
of every node/leaf (metadata extent) as pinned before the new super block
is written. This is to prevent the disk location of log metadata extents
from being reused before the new super block is written, otherwise we
would have a corrupted log tree if before the new super block is written
a crash/reboot happens and the location of any log tree metadata extent
ended up being reused and rewritten.
Even though we pinned the log tree's metadata extents, we were issuing a
discard against them if the fs was mounted with the -o discard option,
resulting in corruption of the log tree if a crash/reboot happened before
writing the new super block - the next time the fs was mounted, during
the log replay process we would find nodes/leafs of the log btree with
a content full of zeroes, causing the process to fail and require the
use of the tool btrfs-zero-log to wipeout the log tree (and all data
previously fsynced becoming lost forever).
Fix this by not doing a discard when pinning an extent. The discard will
be done later when it's safe (after the new super block is committed) at
extent-tree.c:btrfs_finish_extent_commit().
Fixes: e688b7252f78 (Btrfs: fix extent pinning bugs in the tree log) Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Don't wait after sending request for offers to the host. This wait is
unnecessary and simply adds 5 seconds to the boot time.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
time_init invokes timer64_init (which is __init annotation)
since all of these are invoked at init time, lets maintain
consistency by ensuring time_init is marked appropriately
as well.
This fixes the following warning with CONFIG_DEBUG_SECTION_MISMATCH=y
WARNING: vmlinux.o(.text+0x3bfc): Section mismatch in reference from the function time_init() to the function .init.text:timer64_init()
The function time_init() references
the function __init timer64_init().
This is often because time_init lacks a __init
annotation or the annotation of timer64_init is wrong.
Fixes: 546a39546c64 ("C6X: time management") Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Mark Salter <msalter@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
The comparison from the previous line seems to have been erroneously
(partially) copied-and-pasted onto the next. The second line should be
checking req.bytes, not req.lnum.
Coverity CID #139400
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[rw: Fixed comparison] Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Zefan Li <lizefan@huawei.com>
In some of the 'out_not_moved' error paths, lnum may be used
uninitialized. Don't ignore the warning; let's fix it.
This uninitialized variable doesn't have much visible effect in the end,
since we just schedule the PEB for erasure, and its LEB number doesn't
really matter (it just gets printed in debug messages). But let's get it
straight anyway.
Coverity CID #113449
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
If aeb->len >= vol->reserved_pebs, we should not be writing aeb into the
PEB->LEB mapping.
Caught by Coverity, CID #711212.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
the lcd type as defined in the Kconfig is not matching in the code.
as a result the rs, rw and en pins were getting interchanged.
Kconfig defines the value of PANEL_LCD to be 1 if we select custom
configuration but in the code LCD_TYPE_CUSTOM is defined as 5.
my hardware is LCD_TYPE_CUSTOM, but the pins were assigned to it
as pins of LCD_TYPE_OLD, and it was not working.
Now values are corrected with referenece to the values defined in
Kconfig and it is working.
checked on JHD204A lcd with LCD_TYPE_CUSTOM configuration.
The WM8741 DAC supports the following typical audio sampling rates:
44.1kHz, 88.2kHz, 176.4kHz (eg: with a master clock of 22.5792MHz)
32kHz, 48kHz, 96kHz, 192kHz (eg: with a master clock of 24.576MHz)
For the rates lists, we should use 82000 instead of 88235, 176400
instead of 1764000 and 192000 instead of 19200 (seems to be a typo).
Signed-off-by: Sergej Sawazki <ce3a@gmx.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
We should signal connect (pull up dp) after we have already
at peripheral mode, otherwise, the dp may be toggled due to
we reset controller or do disconnect during the initialization
for peripheral, then, the host may be confused during the
enumeration, eg, it finds the reset can't succeed, but the
device is still there, see below error message.
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 1-0:1.0: unable to enumerate USB device on port 1
Fixes: the issue existed when the otg fsm code was added. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
[lizf: Backported to 3.4:
- adjust filename
- adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
This API has changed in commit 6e5e959dde0 (pinctrl: API changes to support
multiple states per device).
Fixes: 6e5e959dde0 ('pinctrl: API changes to support multiple states per device') Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The return value of power_supply_register() call was not checked and
even on error probe() function returned 0. If registering failed then
during unbind the driver tried to unregister power supply which was not
actually registered.
This could lead to memory corruption because power_supply_unregister()
unconditionally cleans up given power supply.
Fix this by checking return status of power_supply_register() call. In
case of failure, clean up sysfs entries and fail the probe.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: 9be0fcb5ed46 ("compal-laptop: add JHL90, battery & hwmon interface") Signed-off-by: Sebastian Reichel <sre@kernel.org>
[lizf: Backported to 3.4: there's no "remove" label. Do cleanup inside if block] Signed-off-by: Zefan Li <lizefan@huawei.com>
There is a race condition between e1000_change_mtu's cleanups and
netpoll, when we change the MTU across jumbo size:
Changing MTU frees all the rx buffers:
e1000_change_mtu -> e1000_down -> e1000_clean_all_rx_rings ->
e1000_clean_rx_ring
Then, close to the end of e1000_change_mtu:
pr_info -> ... -> netpoll_poll_dev -> e1000_clean ->
e1000_clean_rx_irq -> e1000_alloc_rx_buffers -> e1000_alloc_frag
And when we come back to do the rest of the MTU change:
e1000_up -> e1000_configure -> e1000_configure_rx ->
e1000_alloc_jumbo_rx_buffers
alloc_jumbo finds the buffers already != NULL, since data (shared with
page in e1000_rx_buffer->rxbuf) has been re-alloc'd, but it's garbage,
or at least not what is expected when in jumbo state.
This results in an unusable adapter (packets don't get through), and a
NULL pointer dereference on the next call to e1000_clean_rx_ring
(other mtu change, link down, shutdown):
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81194d6e>] put_compound_page+0x7e/0x330
Correctly rollback state if the failure occurs after we have handed over
the ownership of the buffer to the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
Add 04f2:aff1 to ath3k.c supported devices list and btusb.c blacklist, so
that the device can load the ath3k firmware and re-enumerate itself as an
AR3011 device.
ipv6: add check for blackhole or prohibited entry in rt6_redire
There's a check for ip6_null_entry, but it's not enough if the config
CONFIG_IPV6_MULTIPLE_TABLES is selected. Blackhole or prohibited entries
should also be ignored.
This path is for kernel before v3.6, as there's a commit b94f1c0
use icmpv6_notify() instead of rt6_redirect() and rt6_redirect has
been deleted.
When we come to tear things down in netback_remove() and generate the
uevent it is possible that the xenstore directory has already been
removed (details below).
In such cases netback_uevent() won't be able to read the hotplug
script and will write a xenstore error node.
A recent change to the hypervisor exposed this race such that we now
sometimes lose it (where apparently we didn't ever before).
Instead read the hotplug script configuration during setup and use it
for the lifetime of the backend device.
The apparently more obvious fix of moving the transition to
state=Closed in netback_remove() to after the uevent does not work
because it is possible that we are already in state=Closed (in
reaction to the guest having disconnected as it shutdown). Being
already in Closed means the toolstack is at liberty to start tearing
down the xenstore directories. In principal it might be possible to
arrange to unregister the device sooner (e.g on transition to Closing)
such that xenstore would still be there but this state machine is
fragile and prone to anger...
A modern Xen system only relies on the hotplug uevent for driver
domains, when the backend is in the same domain as the toolstack it
will run the necessary setup/teardown directly in the correct sequence
wrt xenstore changes.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
Current implementation of unfreeze_partials() is so complicated,
but benefit from it is insignificant. In addition many code in
do {} while loop have a bad influence to a fail rate of cmpxchg_double_slab.
Under current implementation which test status of cpu partial slab
and acquire list_lock in do {} while loop,
we don't need to acquire a list_lock and gain a little benefit
when front of the cpu partial slab is to be discarded, but this is a rare case.
In case that add_partial is performed and cmpxchg_double_slab is failed,
remove_partial should be called case by case.
I think that these are disadvantages of current implementation,
so I do refactoring unfreeze_partials().
Minimizing code in do {} while loop introduce a reduced fail rate
of cmpxchg_double_slab. Below is output of 'slabinfo -r kmalloc-256'
when './perf stat -r 33 hackbench 50 process 4000 > /dev/null' is done.
No regression is found, but rather we can see slightly better result.
Acked-by: Christoph Lameter <cl@linux.com> Signed-off-by: Joonsoo Kim <js1304@gmail.com> Signed-off-by: Pekka Enberg <penberg@kernel.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
The variable for the 'permissive' module parameter used to be static
but was recently changed to be extern. This puts it in the kernel
global namespace if the driver is built-in, so its name should begin
with a prefix identifying the driver.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Fixes: af6fc858a35b ("xen-pciback: limit guest control of command register") Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
mm/page-writeback.c has several places where 1 is added to the divisor
to prevent division by zero exceptions; however, if the original
divisor is equivalent to -1, adding 1 leads to division by zero.
There are three places where +1 is used for this purpose - one in
pos_ratio_polynom() and two in bdi_position_ratio(). The second one
in bdi_position_ratio() actually triggered div-by-zero oops on a
machine running a 3.10 kernel. The divisor is
x_intercept - bdi_setpoint + 1 == span + 1
span is confirmed to be (u32)-1. It isn't clear how it ended up that
but it could be from write bandwidth calculation underflow fixed by c72efb658f7c ("writeback: fix possible underflow in write bandwidth
calculation").
At any rate, +1 isn't a proper protection against div-by-zero. This
patch converts all +1 protections to |1. Note that
bdi_update_dirty_ratelimit() was already using |1 before this patch.
Signed-off-by: Tejun Heo <tj@kernel.org> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com>
[lizf: Backported to 3.4: drop other two changes as there's only one
such statment in 3.4] Signed-off-by: Zefan Li <lizefan@huawei.com>
In a call to ib_umem_get(), if address is 0x0 and size is
already page aligned, check added in commit 8494057ab5e4
("IB/uverbs: Prevent integer overflow in ib_umem_get address
arithmetic") will refuse to register a memory region that
could otherwise be valid (provided vm.mmap_min_addr sysctl
and mmap_low_allowed SELinux knobs allow userspace to map
something at address 0x0).
This patch allows back such registration: ib_umem_get()
should probably don't care of the base address provided it
can be pinned with get_user_pages().
There's two possible overflows, in (addr + size) and in
PAGE_ALIGN(addr + size), this patch keep ensuring none
of them happen while allowing to pin memory at address
0x0. Anyway, the case of size equal 0 is no more (partially)
handled as 0-length memory region are disallowed by an
earlier check.
Link: http://mid.gmane.org/cover.1428929103.git.ydroneaud@opteya.com Cc: Shachar Raindel <raindel@mellanox.com> Cc: Jack Morgenstein <jackm@mellanox.com> Cc: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Yann Droneaud <ydroneaud@opteya.com> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Reviewed-by: Haggai Eran <haggaie@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
It added some sanity checks to ignore potential garbage in CDC headers but
also introduced a potential infinite loop. This can happen at the first
loop iteration (elength = 0 in that case) if the description isn't a
DT_CS_INTERFACE or later if 'buffer[0]' is zero.
It should also be noted that the wrong length was being added to 'buffer'
in case 'buffer[1]' was not a DT_CS_INTERFACE descriptor, since elength was
assigned after that check in the loop.
A specially crafted USB device could be used to trigger this infinite loop.
Fixes: 7e860a6e7aa6 ("cdc-acm: add sanity checks") Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com> Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com> CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> CC: Oliver Neukum <oneukum@suse.de> CC: Adam Lee <adam8157@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
return the value instead, and have path_init() do the assignment. Broken by
"vfs: Fix absolute RCU path walk failures due to uninitialized seq number",
which was Cc-stable with 2.6.38+ as destination. This one should go where
it went.
To avoid dummy value returned in case when root is already set (it would do
no harm, actually, since the only caller that doesn't ignore the return value
is guaranteed to have nd->root *not* set, but it's more obvious that way),
lift the check into callers. And do the same to set_root(), to keep them
in sync.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Cc: Ian Jackson <ian.jackson@eu.citrix.com>
[lizf: the previous backport of this upstream commit is buggy. fix it] Signed-off-by: Zefan Li <lizefan@huawei.com>
took a pci_dev, but they really depend only on the pci_bus. And we want to
use them in resource allocation paths where we have the bus but not a
device, so this patch converts them to take the pci_bus instead of the
pci_dev:
In fact, with standard PCI-PCI bridges, they only depend on the host
bridge, because that's the only place address translation occurs, but
we aren't going that far yet.
[bhelgaas: changelog] Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Dirk Behme <dirk.behme@gmail.com>
[lizf: Backported to 3.4:
- make changes to pci_host_bridge() instead of find_pci_root_bus()
- adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
A huge amount of NIC drivers use the DMA API, however if
compiled under 32-bit an very important part of the DMA API can
be ommitted leading to the drivers not working at all
(especially if used with 'swiotlb=force iommu=soft').
As Prashant Sreedharan explains it: "the driver [tg3] uses
DEFINE_DMA_UNMAP_ADDR(), dma_unmap_addr_set() to keep a copy of
the dma "mapping" and dma_unmap_addr() to get the "mapping"
value. On most of the platforms this is a no-op, but ... with
"iommu=soft and swiotlb=force" this house keeping is required,
... otherwise we pass 0 while calling pci_unmap_/pci_dma_sync_
instead of the DMA address."
As such enable this even when using 32-bit kernels.
Reported-by: Ian Jackson <Ian.Jackson@eu.citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: David S. Miller <davem@davemloft.net> Acked-by: Prashant Sreedharan <prashant@broadcom.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Chan <mchan@broadcom.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: boris.ostrovsky@oracle.com Cc: cascardo@linux.vnet.ibm.com Cc: david.vrabel@citrix.com Cc: sanjeevb@broadcom.com Cc: siva.kallam@broadcom.com Cc: vyasevich@gmail.com Cc: xen-devel@lists.xensource.com Link: http://lkml.kernel.org/r/20150417190448.GA9462@l.oracle.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Ben Hutchings <ben@decadent.org.uk>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
perl.h from new Perl release doesn't like -Wundef and -Wswitch-default:
/usr/lib/perl5/core_perl/CORE/perl.h:548:5: error: "SILENT_NO_TAINT_SUPPORT" is not defined [-Werror=undef]
#if SILENT_NO_TAINT_SUPPORT && !defined(NO_TAINT_SUPPORT)
^
/usr/lib/perl5/core_perl/CORE/perl.h:556:5: error: "NO_TAINT_SUPPORT" is not defined [-Werror=undef]
#if NO_TAINT_SUPPORT
^
In file included from /usr/lib/perl5/core_perl/CORE/perl.h:3471:0,
from util/scripting-engines/trace-event-perl.c:30:
/usr/lib/perl5/core_perl/CORE/sv.h:1455:5: error: "NO_TAINT_SUPPORT" is not defined [-Werror=undef]
#if NO_TAINT_SUPPORT
^
In file included from /usr/lib/perl5/core_perl/CORE/perl.h:3472:0,
from util/scripting-engines/trace-event-perl.c:30:
/usr/lib/perl5/core_perl/CORE/regexp.h:436:5: error: "NO_TAINT_SUPPORT" is not defined [-Werror=undef]
#if NO_TAINT_SUPPORT
^
In file included from /usr/lib/perl5/core_perl/CORE/hv.h:592:0,
from /usr/lib/perl5/core_perl/CORE/perl.h:3480,
from util/scripting-engines/trace-event-perl.c:30:
/usr/lib/perl5/core_perl/CORE/hv_func.h: In function ‘S_perl_hash_siphash_2_4’:
/usr/lib/perl5/core_perl/CORE/hv_func.h:222:3: error: switch missing default case [-Werror=switch-default]
switch( left )
^
/usr/lib/perl5/core_perl/CORE/hv_func.h: In function ‘S_perl_hash_superfast’:
/usr/lib/perl5/core_perl/CORE/hv_func.h:274:5: error: switch missing default case [-Werror=switch-default]
switch (rem) { \
^
/usr/lib/perl5/core_perl/CORE/hv_func.h: In function ‘S_perl_hash_murmur3’:
/usr/lib/perl5/core_perl/CORE/hv_func.h:398:5: error: switch missing default case [-Werror=switch-default]
switch(bytes_in_carry) { /* how many bytes in carry */
^
Let's disable the warnings for code which uses perl.h.
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name> Cc: Ingo Molnar <mingo@redhat.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/1372063394-20126-1-git-send-email-kirill@shutemov.name Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Vinson Lee <vlee@twopensource.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Running mtd-utils/tests/ubi-tests/io_basic.c could cause
soft lockup or watchdog reset. It is because *updatevol*
will perform ubi_check_volume() after updating finish
and this function will full scan the updated lebs if the
volume is initialized as STATIC_VOLUME.
This patch adds *cond_resched()* in the loop of lebs scan
to avoid soft lockup.
Helped by Richard Weinberger <richard@nod.at>
[ 2158.067096] INFO: rcu_sched self-detected stall on CPU { 1} (t=2101 jiffies g=1606 c=1605 q=56)
[ 2158.172867] CPU: 1 PID: 2073 Comm: io_basic Tainted: G O 3.10.53 #21
[ 2158.172898] [<c000f624>] (unwind_backtrace+0x0/0x120) from [<c000c294>] (show_stack+0x10/0x14)
[ 2158.172918] [<c000c294>] (show_stack+0x10/0x14) from [<c008ac3c>] (rcu_check_callbacks+0x1c0/0x660)
[ 2158.172936] [<c008ac3c>] (rcu_check_callbacks+0x1c0/0x660) from [<c002b480>] (update_process_times+0x38/0x64)
[ 2158.172953] [<c002b480>] (update_process_times+0x38/0x64) from [<c005ff38>] (tick_sched_handle+0x54/0x60)
[ 2158.172966] [<c005ff38>] (tick_sched_handle+0x54/0x60) from [<c00601ac>] (tick_sched_timer+0x44/0x74)
[ 2158.172978] [<c00601ac>] (tick_sched_timer+0x44/0x74) from [<c003f348>] (__run_hrtimer+0xc8/0x1b8)
[ 2158.172992] [<c003f348>] (__run_hrtimer+0xc8/0x1b8) from [<c003fd9c>] (hrtimer_interrupt+0x128/0x2a4)
[ 2158.173007] [<c003fd9c>] (hrtimer_interrupt+0x128/0x2a4) from [<c0246f1c>] (arch_timer_handler_virt+0x28/0x30)
[ 2158.173022] [<c0246f1c>] (arch_timer_handler_virt+0x28/0x30) from [<c0086214>] (handle_percpu_devid_irq+0x9c/0x124)
[ 2158.173036] [<c0086214>] (handle_percpu_devid_irq+0x9c/0x124) from [<c0082bd8>] (generic_handle_irq+0x20/0x30)
[ 2158.173049] [<c0082bd8>] (generic_handle_irq+0x20/0x30) from [<c000969c>] (handle_IRQ+0x64/0x8c)
[ 2158.173060] [<c000969c>] (handle_IRQ+0x64/0x8c) from [<c0008544>] (gic_handle_irq+0x3c/0x60)
[ 2158.173074] [<c0008544>] (gic_handle_irq+0x3c/0x60) from [<c02f0f80>] (__irq_svc+0x40/0x50)
[ 2158.173083] Exception stack(0xc4043c98 to 0xc4043ce0)
[ 2158.173092] 3c80: c4043ce400000019
[ 2158.173102] 3ca0: 1f8a865fc050ad101f8a864c00000031c04b59700003ebce00000000f3550000
[ 2158.173113] 3cc0: bf00bc68000008000003ebcec4043ce0c0186d14c0186cb880000013ffffffff
[ 2158.173130] [<c02f0f80>] (__irq_svc+0x40/0x50) from [<c0186cb8>] (read_current_timer+0x4/0x38)
[ 2158.173145] [<c0186cb8>] (read_current_timer+0x4/0x38) from [<1f8a865f>] (0x1f8a865f)
[ 2183.927097] BUG: soft lockup - CPU#1 stuck for 22s! [io_basic:2073]
[ 2184.002229] Modules linked in: nandflash(O) [last unloaded: nandflash]
Signed-off-by: Wang Kai <morgan.wang@huawei.com> Signed-off-by: hujianyang <hujianyang@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Zefan Li <lizefan@huawei.com>
skb_gso_segment has three possible return values:
1. a pointer to the first segmented skb
2. an errno value (IS_ERR())
3. NULL. This can happen when GSO is used for header verification.
However, several callers currently test IS_ERR instead of IS_ERR_OR_NULL
and would oops when NULL is returned.
Note that these call sites should never actually see such a NULL return
value; all callers mask out the GSO bits in the feature argument.
However, there have been issues with some protocol handlers erronously not
respecting the specified feature mask in some cases.
It is preferable to get 'have to turn off hw offloading, else slow' reports
rather than 'kernel crashes'.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <ben@decadent.org.uk>
[lizf: Backported to 3.4: drop some hunks as there are fewer skb_gso_segment()
users in 3.4] Signed-off-by: Zefan Li <lizefan@huawei.com>
There is a potential memory leak in hpsa_kdump_hard_reset_controller.
Reviewed-by: Don Brace <don.brace@pmcs.com> Reviewed-by: Scott Teel <scott.teel@pmcs.com> Signed-off-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Don Brace <don.brace@pmcs.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Vinson Lee <vlee@twopensource.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Sometimes when the card is restarted it may cause -
"irq 16: nobody cared (try booting with the "irqpoll" option)"
that is likely caused so, that the card, after the hard reset
finishes, pulls on the irq. Disabling the ints before or after
the hpsa_kdump_hard_reset_controller fixes it.
At this point we can't know in which state the card is,
so using SA5_INTR_OFF + SA5_REPLY_INTR_MASK_OFFSET defines directly,
instead of the function the drivers provides, seems to be apropriate.
Reviewed-by: Scott Teel <scott.teel@pmcs.com> Signed-off-by: Don Brace <don.brace@pmcs.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Vinson Lee <vlee@twopensource.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Add a call to pci_set_master(...) missing in the previous
patch "hpsa: refine the pci enable/disable handling".
Found thanks to Rob Elliot.
Signed-off-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Robert Elliott <elliott@hp.com> Tested-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Vinson Lee <vlee@twopensource.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
When a second(kdump) kernel starts and the hard reset method is used
the driver calls pci_disable_device without previously enabling it,
so the kernel shows a warning -
[ 16.876248] WARNING: at drivers/pci/pci.c:1431 pci_disable_device+0x84/0x90()
[ 16.882686] Device hpsa
disabling already-disabled device
...
This patch fixes it, in addition to this I tried to balance also some other pairs
of enable/disable device in the driver.
Unfortunately I wasn't able to verify the functionality for the case of a sw reset,
because of a lack of proper hw.
Signed-off-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Vinson Lee <vlee@twopensource.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
`spidev_message()` sums the lengths of the individual SPI transfers to
determine the overall SPI message length. It restricts the total
length, returning an error if too long, but it does not check for
arithmetic overflow. For example, if the SPI message consisted of two
transfers and the first has a length of 10 and the second has a length
of (__u32)(-1), the total length would be seen as 9, even though the
second transfer is actually very long. If the second transfer specifies
a null `rx_buf` and a non-null `tx_buf`, the `copy_from_user()` could
overrun the spidev's pre-allocated tx buffer before it reaches an
invalid user memory address. Fix it by checking that neither the total
nor the individual transfer lengths exceed the maximum allowed value.
Thanks to Dan Carpenter for reporting the potential integer overflow.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Mark Brown <broonie@kernel.org>
[Ian Abbott: Note: original commit compares the lengths to INT_MAX instead
of bufsiz due to changes in earlier commits.] Signed-off-by: Zefan Li <lizefan@huawei.com>
Commit 746c9e9f92dd "of/base: Fix PowerPC address parsing hack" limited
the applicability of the workaround whereby a missing ranges is treated
as an empty ranges. This workaround was hiding a bug in the etsec2
device tree nodes, which have children with reg, but did not have
ranges.
Signed-off-by: Scott Wood <scottwood@freescale.com> Reported-by: Alexander Graf <agraf@suse.de> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Ben Hutchings [Tue, 17 Feb 2015 01:46:53 +0000 (01:46 +0000)]
splice: Apply generic position and size checks to each write
3.2.67-rc1 review patch. If anyone has any objections, please let me know.
------------------
From: Ben Hutchings <ben@decadent.org.uk>
We need to check the position and size of file writes against various
limits, using generic_write_check(). This was not being done for
the splice write path. It was fixed upstream by commit 8d0207652cbe
("->splice_write() via ->write_iter()") but we can't apply that.
CVE-2014-7822
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
The stop machine logic can lock up if all but one of the migration
threads make it through the disable-irq step and the one remaining
thread gets stuck in __do_softirq. The reason __do_softirq can hang is
that it has a bail-out based on jiffies timeout, but in the lockup case,
jiffies itself is not incremented.
To work around this, re-add the max_restart counter in __do_irq and stop
processing irqs after 10 restarts.
Thanks to Tejun Heo and Rusty Russell and others for helping me track
this down.
This was introduced in 3.9 by commit c10d73671ad3 ("softirq: reduce
latencies").
It may be worth looking into ath9k to see if it has issues with its irq
handler at a later date.
The hang stack traces look something like this:
------------[ cut here ]------------
WARNING: at kernel/watchdog.c:245 watchdog_overflow_callback+0x9c/0xa7()
Watchdog detected hard LOCKUP on cpu 2
Modules linked in: ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nfsv4 auth_rpcgss nfs fscache nf_nat_ipv4 nf_nat veth 8021q garp stp mrp llc pktgen lockd sunrpc]
Pid: 23, comm: migration/2 Tainted: G C 3.9.4+ #11
Call Trace:
<NMI> warn_slowpath_common+0x85/0x9f
warn_slowpath_fmt+0x46/0x48
watchdog_overflow_callback+0x9c/0xa7
__perf_event_overflow+0x137/0x1cb
perf_event_overflow+0x14/0x16
intel_pmu_handle_irq+0x2dc/0x359
perf_event_nmi_handler+0x19/0x1b
nmi_handle+0x7f/0xc2
do_nmi+0xbc/0x304
end_repeat_nmi+0x1e/0x2e
<<EOE>>
cpu_stopper_thread+0xae/0x162
smpboot_thread_fn+0x258/0x260
kthread+0xc7/0xcf
ret_from_fork+0x7c/0xb0
---[ end trace 4947dfa9b0a4cec3 ]---
BUG: soft lockup - CPU#1 stuck for 22s! [migration/1:17]
Modules linked in: ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nfsv4 auth_rpcgss nfs fscache nf_nat_ipv4 nf_nat veth 8021q garp stp mrp llc pktgen lockd sunrpc]
irq event stamp: 835637905
hardirqs last enabled at (835637904): __do_softirq+0x9f/0x257
hardirqs last disabled at (835637905): apic_timer_interrupt+0x6d/0x80
softirqs last enabled at (5654720): __do_softirq+0x1ff/0x257
softirqs last disabled at (5654725): irq_exit+0x5f/0xbb
CPU 1
Pid: 17, comm: migration/1 Tainted: G WC 3.9.4+ #11 To be filled by O.E.M. To be filled by O.E.M./To be filled by O.E.M.
RIP: tasklet_hi_action+0xf0/0xf0
Process migration/1
Call Trace:
<IRQ>
__do_softirq+0x117/0x257
irq_exit+0x5f/0xbb
smp_apic_timer_interrupt+0x8a/0x98
apic_timer_interrupt+0x72/0x80
<EOI>
printk+0x4d/0x4f
stop_machine_cpu_stop+0x22c/0x274
cpu_stopper_thread+0xae/0x162
smpboot_thread_fn+0x258/0x260
kthread+0xc7/0xcf
ret_from_fork+0x7c/0xb0
Signed-off-by: Ben Greear <greearb@candelatech.com> Acked-by: Tejun Heo <tj@kernel.org> Acked-by: Pekka Riikonen <priikone@iki.fi> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[xr: Backported to 3.4: Adjust context] Signed-off-by: Rui Xiang <rui.xiang@huawei.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
In various network workloads, __do_softirq() latencies can be up
to 20 ms if HZ=1000, and 200 ms if HZ=100.
This is because we iterate 10 times in the softirq dispatcher,
and some actions can consume a lot of cycles.
This patch changes the fallback to ksoftirqd condition to :
- A time limit of 2 ms.
- need_resched() being set on current task
When one of this condition is met, we wakeup ksoftirqd for further
softirq processing if we still have pending softirqs.
Using need_resched() as the only condition can trigger RCU stalls,
as we can keep BH disabled for too long.
I ran several benchmarks and got no significant difference in
throughput, but a very significant reduction of latencies (one order
of magnitude) :
In following bench, 200 antagonist "netperf -t TCP_RR" are started in
background, using all available cpus.
Then we start one "netperf -t TCP_RR", bound to the cpu handling the NIC
IRQ (hard+soft)
Before patch :
# netperf -H 7.7.7.84 -t TCP_RR -T2,2 -- -k
RT_LATENCY,MIN_LATENCY,MAX_LATENCY,P50_LATENCY,P90_LATENCY,P99_LATENCY,MEAN_LATENCY,STDDEV_LATENCY
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET
to 7.7.7.84 () port 0 AF_INET : first burst 0 : cpu bind
RT_LATENCY=550110.424
MIN_LATENCY=146858
MAX_LATENCY=997109
P50_LATENCY=305000
P90_LATENCY=550000
P99_LATENCY=710000
MEAN_LATENCY=376989.12
STDDEV_LATENCY=184046.92
After patch :
# netperf -H 7.7.7.84 -t TCP_RR -T2,2 -- -k
RT_LATENCY,MIN_LATENCY,MAX_LATENCY,P50_LATENCY,P90_LATENCY,P99_LATENCY,MEAN_LATENCY,STDDEV_LATENCY
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET
to 7.7.7.84 () port 0 AF_INET : first burst 0 : cpu bind
RT_LATENCY=40545.492
MIN_LATENCY=9834
MAX_LATENCY=78366
P50_LATENCY=33583
P90_LATENCY=59000
P99_LATENCY=69000
MEAN_LATENCY=38364.67
STDDEV_LATENCY=12865.26
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: David Miller <davem@davemloft.net> Cc: Tom Herbert <therbert@google.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[xr: Backported to 3.4: Adjust context] Signed-off-by: Rui Xiang <rui.xiang@huawei.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
The root cause seems to be the
default_send_IPI_mask_allbutself_phys() takes quite some time (I
measured it could be several ms) to complete sending NMIs to all
the other 23 CPUs, and for HZ=250/1000 system, the time is long
enough for a timer interrupt to happen, which will in turn
trigger to kick load balance to a stopped CPU and cause this
warning in native_smp_send_reschedule().
So disabling the local irq before stop_other_cpu() can fix this
problem (tested 25 times reboot ok), and it is fine as there
should be nobody caring the timer interrupt in such reboot
stage.
The latest 3.4 kernel slightly changes this behavior by sending
REBOOT_VECTOR first and only send NMI_VECTOR if the REBOOT_VCTOR
fails, and this patch is still needed to prevent the problem.
Signed-off-by: Feng Tang <feng.tang@intel.com> Acked-by: Don Zickus <dzickus@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20120530231541.4c13433a@feng-i7 Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Vinson Lee <vlee@twopensource.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Adds an entry for Creative USB X-Fi to the rc_config array in
mixer_quirks.c to allow use of volume knob on the device.
Adds support for newer X-Fi Pro card, known as "Model No. SB1095"
with USB ID "041e:3237"
Signed-off-by: Dmitry M. Fedin <dmitry.fedin@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
"ocfs2 syncs the wrong range" had been broken; prior to it the
code was doing the wrong thing in case of O_APPEND, all right,
but _after_ it we were syncing the wrong range in 100% cases.
*ppos, aka iocb->ki_pos is incremented prior to that point,
so we are always doing sync on the area _after_ the one we'd
written to.
Spotted by Joseph Qi <joseph.qi@huawei.com> back in January;
unfortunately, I'd missed his mail back then ;-/
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
SCSI transport drivers and SCSI LLDs block a SCSI device if the
transport layer is not operational. This means that in this state
no requests should be processed, even if the REQ_PREEMPT flag has
been set. This patch avoids that a rescan shortly after a cable
pull sporadically triggers the following kernel oops:
Reported-by: Max Gurtuvoy <maxg@mellanox.com> Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Kernel panic was happening as iscsi_host_remove() was called on
a host which was not yet added.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Properly verify that the resulting page aligned end address is larger
than both the start address and the length of the memory area requested.
Both the start and length arguments for ib_umem_get are controlled by
the user. A misbehaving user can provide values which will cause an
integer overflow when calculating the page aligned end address.
This overflow can cause also miscalculation of the number of pages
mapped, and additional logic issues.
Addresses: CVE-2014-8159 Signed-off-by: Shachar Raindel <raindel@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
There's an issue with the way the RX A-MPDU reorder timer is
deleted that can cause a kernel crash like this:
* tid_rx is removed - call_rcu(ieee80211_free_tid_rx)
* station is destroyed
* reorder timer fires before ieee80211_free_tid_rx() runs,
accessing the station, thus potentially crashing due to
the use-after-free
The station deletion is protected by synchronize_net(), but
that isn't enough -- ieee80211_free_tid_rx() need not have
run when that returns (it deletes the timer.) We could use
rcu_barrier() instead of synchronize_net(), but that's much
more expensive.
Instead, to fix this, add a field tracking that the session
is being deleted. In this case, the only re-arming of the
timer happens with the reorder spinlock held, so make that
code not rearm it if the session is being deleted and also
delete the timer after setting that field. This ensures the
timer cannot fire after ___ieee80211_stop_rx_ba_session()
returns, which fixes the problem.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
The ASRock Q1900DC-ITX mainboard (Baytrail-D) hangs randomly in
both BIOS and UEFI mode while rebooting unless reboot=pci is
used. Add a quirk to reboot via the pci method.
The problem is very intermittent and hard to debug, it might succeed
rebooting just fine 40 times in a row - but fails half a dozen times
the next day. It seems to be slightly less common in BIOS CSM mode
than native UEFI (with the CSM disabled), but it does happen in either
mode. Since I've started testing this patch in late january, rebooting
has been 100% reliable.
Most of the time it already hangs during POST, but occasionally it
might even make it through the bootloader and the kernel might even
start booting, but then hangs before the mode switch. The same symptoms
occur with grub-efi, gummiboot and grub-pc, just as well as (at least)
kernel 3.16-3.19 and 4.0-rc6 (I haven't tried older kernels than 3.16).
Upgrading to the most current mainboard firmware of the ASRock
Q1900DC-ITX, version 1.20, does not improve the situation.
( Searching the web seems to suggest that other Bay Trail-D mainboards
might be affected as well. )
-- Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Cc: Matt Fleming <matt.fleming@intel.com> Link: http://lkml.kernel.org/r/20150330224427.0fb58e42@mir Signed-off-by: Ingo Molnar <mingo@kernel.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Use readb() and memcpy_fromio() accessors instead.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
This patch uses the existing CALAO Systems ftdi_8u2232c_probe in order
to avoid attaching a TTY to the JTAG port as this board is based on the
CALAO Systems reference design and needs the same fix up.
Signed-off-by: Doug Goldstein <cardoe@cardoe.com>
[johan: clean up probe logic ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
Fixes: e7ed828f10bd8 ("netlink: support setting devgroup parameters") Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
When a device with an isochronous endpoint is plugged into the Intel
xHCI host controller, and the driver submits multiple frames per URB,
the xHCI driver will set the Block Event Interrupt (BEI) flag on all
but the last TD for the URB. This causes the host controller to place
an event on the event ring, but not send an interrupt. When the last
TD for the URB completes, BEI is cleared, and we get an interrupt for
the whole URB.
However, under Intel xHCI host controllers, if the event ring is full
of events from transfers with BEI set, an "Event Ring is Full" event
will be posted to the last entry of the event ring, but no interrupt
is generated. Host will cease all transfer and command executions and
wait until software completes handling the pending events in the event
ring. That means xHC stops, but event of "event ring is full" is not
notified. As the result, the xHC looks like dead to user.
This patch is to apply XHCI_AVOID_BEI quirk to Intel xHC devices. And
it should be backported to kernels as old as 3.0, that contains the
commit 69e848c2090a ("Intel xhci: Support EHCI/xHCI port switching.").
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Tested-by: Alistair Grant <akgrant0710@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Linux xHCI driver doesn't report and handle port cofig error change.
If Port Configure Error for root hub port occurs, CEC bit in PORTSC
would be set by xHC and remains 1. This happends when the root port
fails to configure its link partner, e.g. the port fails to exchange
port capabilities information using Port Capability LMPs.
Then the Port Status Change Events will be blocked until all status
change bits(CEC is one of the change bits) are cleared('0') (refer to
xHCI spec 4.19.2). Otherwise, the port status change event for this
root port will not be generated anymore, then root port would look
like dead for user and can't be recovered until a Host Controller
Reset(HCRST).
This patch is to check CEC bit in PORTSC in xhci_get_port_status()
and set a Config Error in the return status if CEC is set. This will
cause a ClearPortFeature request, where CEC bit is cleared in
xhci_clear_port_change_bit().
[The commit log is based on initial Marvell patch posted at
http://marc.info/?l=linux-kernel&m=142323612321434&w=2]
Reported-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lizf: Backported to 3.4:
- adjust indentation
- s/raw_port_status/temp/] Signed-off-by: Zefan Li <lizefan@huawei.com>
Under intermittent network outages, find_writable_file() is susceptible
to the following race condition, which results in a user-after-free in
the cifs_writepages code-path:
At this point we loop back through with an invalid inv_file pointer
and a refind value of 1. On second pass, inv_file is not overwritten on
openFileList traversal, and is subsequently dereferenced.
Signed-off-by: David Disseldorp <ddiss@suse.de> Reviewed-by: Jeff Layton <jlayton@samba.org> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
We have a HP machine which use the codec node 0x17 connecting the
internal speaker, and from the node capability, we saw the EAPD,
if we don't set the EAPD on for this node, the internal speaker
can't output any sound.
BugLink: https://bugs.launchpad.net/bugs/1436745 Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
Fix B-tree corruption when a new record is inserted at position 0 in the
node in hfs_brec_insert(). In this case a hfs_brec_update_parent() is
called to update the parent index node (if exists) and it is passed
hfs_find_data with a search_key containing a newly inserted key instead
of the key to be updated. This results in an inconsistent index node.
The bug reproduces on my machine after an extents overflow record for
the catalog file (CNID=4) is inserted into the extents overflow B-tree.
Because of a low (reserved) value of CNID=4, it has to become the first
record in the first leaf node.
A change in hfs_brec_insert() makes hfs_brec_update_parent() work
correctly by preventing it from getting fd->record=-1 value from
__hfs_brec_find().
Along the way, I removed duplicate code with unification of the if
condition. The resulting code is equivalent to the original code
because node is never 0.
Also hfs_brec_update_parent() will now return an error after getting a
negative fd->record value. However, the return value of
hfs_brec_update_parent() is not checked anywhere in the file and I'm
leaving it unchanged by this patch. brec.c lacks error checking after
some other calls too, but this issue is of less importance than the one
being fixed by this patch.
Signed-off-by: Sergei Antonov <saproj@gmail.com> Cc: Joe Perches <joe@perches.com> Reviewed-by: Vyacheslav Dubeyko <slava@dubeyko.com> Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Anton Altaparmakov <aia21@cam.ac.uk> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Return a negative error value like the rest of the entries in this function.
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
[PM: tweaked subject line] Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
2f800fbd777b ("writeback: fix dirtied pages accounting on redirty")
introduced account_page_redirty() which reverts stat updates for a
redirtied page, making BDI_DIRTIED no longer monotonically increasing.
bdi_update_write_bandwidth() uses the delta in BDI_DIRTIED as the
basis for bandwidth calculation. While unlikely, since the above
patch, the newer value may be lower than the recorded past value and
underflow the bandwidth calculation leading to a wild result.
Fix it by subtracing min of the old and new values when calculating
delta. AFAIK, there hasn't been any report of it happening but the
resulting erratic behavior would be non-critical and temporary, so
it's possible that the issue is happening without being reported. The
risk of the fix is very low, so tagged for -stable.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jan Kara <jack@suse.cz> Cc: Wu Fengguang <fengguang.wu@intel.com> Cc: Greg Thelen <gthelen@google.com> Fixes: 2f800fbd777b ("writeback: fix dirtied pages accounting on redirty") Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
When non-realtime tasks get priority-inheritance boosted to a realtime
scheduling class, RLIMIT_RTTIME starts to apply to them. However, the
counter used for checking this (the same one used for SCHED_RR
timeslices) was not getting reset. This meant that tasks running with a
non-realtime scheduling class which are repeatedly boosted to a realtime
one, but never block while they are running realtime, eventually hit the
timeout without ever running for a time over the limit. This patch
resets the realtime timeslice counter when un-PI-boosting from an RT to
a non-RT scheduling class.
I have some test code with two threads and a shared PTHREAD_PRIO_INHERIT
mutex which induces priority boosting and spins while boosted that gets
killed by a SIGXCPU on non-fixed kernels but doesn't with this patch
applied. It happens much faster with a CONFIG_PREEMPT_RT kernel, and
does happen eventually with PREEMPT_VOLUNTARY kernels.
Signed-off-by: Brian Silverman <brian@peloton-tech.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: austin@peloton-tech.com Link: http://lkml.kernel.org/r/1424305436-6716-1-git-send-email-brian@peloton-tech.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
[lizf: Backported to 3.4: adjust contest] Signed-off-by: Zefan Li <lizefan@huawei.com>
Which is caused by an irq_work generating new irq_work and therefore
not allowing forward progress.
This happens because processing the perf irq_work triggers another
perf event (tracepoint stuff) which in turn generates an irq_work ad
infinitum.
Avoid this by raising the recursion counter in the irq_work -- which
effectively disables all software events (including tracepoints) from
actually triggering again.
Reported-by: Vince Weaver <vincent.weaver@maine.edu> Tested-by: Vince Weaver <vincent.weaver@maine.edu> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Steven Rostedt <rostedt@goodmis.org> Link: http://lkml.kernel.org/r/20150219170311.GH21418@twins.programming.kicks-ass.net Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
On a MIPS Malta board, tons of fifo underflow errors have been observed
when using u-boot as bootloader instead of YAMON. The reason for that
is that YAMON used to set the pcnet device to SRAM mode but u-boot does
not. As a result, the default Tx threshold (64 bytes) is now too small to
keep the fifo relatively used and it can result to Tx fifo underflow errors.
As a result of which, it's best to setup the SRAM on supported controllers
so we can always use the NOUFLO bit.
Cc: <netdev@vger.kernel.org> Cc: <linux-kernel@vger.kernel.org> Cc: Don Fry <pcnet32@frontier.com> Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
global_update_bandwidth() uses static variable update_time as the
timestamp for the last update but forgets to initialize it to
INITIALIZE_JIFFIES.
This means that global_dirty_limit will be 5 mins into the future on
32bit and some large amount jiffies into the past on 64bit. This
isn't critical as the only effect is that global_dirty_limit won't be
updated for the first 5 mins after booting on 32bit machines,
especially given the auxiliary nature of global_dirty_limit's role -
protecting against global dirty threshold's sudden dips; however, it
does lead to unintended suboptimal behavior. Fix it.
Fixes: c42843f2f0bb ("writeback: introduce smoothed global dirty limit") Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Jan Kara <jack@suse.cz> Cc: Wu Fengguang <fengguang.wu@intel.com> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
This patch fixes a NULL pointer dereference OOPs with pSCSI backends
within target_core_stat.c code. The bug is caused by a configfs attr
read if no pscsi_dev_virt->pdv_sd has been configured.
Reported-by: Olaf Hering <olaf@aepfle.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
This patch adds a missing set of conditional check braces in
ft_invl_hw_context() originally introduced by commit dcd998ccd
when handling DDP failures in ft_recv_write_data() code.
For RoCE ports, we set the u32 PMA values based on u64 HCA counters. In case of
overflow, according to the IB spec, we have to saturate a counter to its
max value, do that.
Fixes: c37791349cc7 ('IB/mlx4: Support PMA counters for IBoE') Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[lizf: Backported to 3.4:
- adjust context
- open-code U32_MAX] Signed-off-by: Zefan Li <lizefan@huawei.com>
As HT/VHT depend heavily on QoS/WMM, it's not a good idea to
let userspace add clients that have HT/VHT but not QoS/WMM.
Since it does so in certain cases we've observed (client is
using HT IEs but not QoS/WMM) just ignore the HT/VHT info at
this point and don't pass it down to the drivers which might
unconditionally use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[lizf: Backported to 3.4:
- adjust context
- 3.4 doesn't support VHT] Signed-off-by: Zefan Li <lizefan@huawei.com>
The kernel crypto API logic requires the caller to provide the
length of (ciphertext || authentication tag) as cryptlen for the
AEAD decryption operation. Thus, the cipher implementation must
calculate the size of the plaintext output itself and cannot simply use
cryptlen.
The RFC4106 GCM decryption operation tries to overwrite cryptlen memory
in req->dst. As the destination buffer for decryption only needs to hold
the plaintext memory but cryptlen references the input buffer holding
(ciphertext || authentication tag), the assumption of the destination
buffer length in RFC4106 GCM operation leads to a too large size. This
patch simply uses the already calculated plaintext size.
In addition, this patch fixes the offset calculation of the AAD buffer
pointer: as mentioned before, cryptlen already includes the size of the
tag. Thus, the tag does not need to be added. With the addition, the AAD
will be written beyond the already allocated buffer.
Note, this fixes a kernel crash that can be triggered from user space
via AF_ALG(aead) -- simply use the libkcapi test application
from [1] and update it to use rfc4106-gcm-aes.
Using [1], the changes were tested using CAVS vectors to demonstrate
that the crypto operation still delivers the right results.
[1] http://www.chronox.de/libkcapi.html
CC: Tadeusz Struk <tadeusz.struk@intel.com> Signed-off-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Zefan Li <lizefan@huawei.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The one in do_debug() is probably harmless, but better safe than sorry.
Signed-off-by: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/d67deaa9df5458363623001f252d1aee3215d014.1425948056.git.luto@amacapital.net Signed-off-by: Ingo Molnar <mingo@kernel.org>
[lizf: Backported to 3.4: drop the change to do_bounds()] Signed-off-by: Zefan Li <lizefan@huawei.com>
projects / thirdparty / kernel / stable.git / log
