4c619b3eed x86: Check IFUNC definition in unrelocated executable [BZ #20019] 87450ecf8a x86: Set header.feature_1 in TCB for always-on CET [BZ #27177] 2b4f67c2b3 Update for [BZ #27130] fix 1a24bbd43e x86-64: Avoid rep movsb with short distance [BZ #27130]
Rui Salvaterra [Wed, 2 Dec 2020 15:42:07 +0000 (15:42 +0000)]
ramips: mt7621: refresh the kernel config
The removed config symbols are already enabled by the generic kernel
configuration (or by default), while the added ones are forcefully
enabled by the specific architecture.
ath79: remove USB port definition for TP-Link TL-WR810N v1
The USB port definition is only needed when it is linked to a USB
LED. Since there is none for this device, we might as well remove
the port definition.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Flashing procedure is identical to other ubnt devices.
https://openwrt.org/toh/ubiquiti/common
Flashing through factory firmware
1. Ensure firmware version v8.7.0 is installed.
Up/downgrade to this exact version.
2. Patch fwupdate.real binary using
`hexdump -Cv /bin/ubntbox | sed 's/14 40 fe 27/00 00 00 00/g' | \
hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using
`chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWrt using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot
(copied from Ubiquiti NanoBeam AC and modified)
Flashing from serial console
1. Connect serial console (115200 baud)
2. Connect ethernet to a network with a TFTP server, through a
passive PoE injector.
3. Press a key to obtain a u-boot prompt
4. Set your TFTP server's ip address, with:
setenv serverip <tftp-server-address>
5. Set the Bullet AC's ip address, with:
setenv ipaddr <bullet-ac-address>
6. Set the boot file, with:
setenv bootfile <name-of-initramfs-binary-on-tftp-server>
7. Fetch the binary with tftp:
tftpboot
8. Boot the initramfs binary:
bootm
9. From the initramfs, fetch the sysupgrade binary, and flash it with
sysupgrade.
The Bullet AC is identified as a 2WA board by Ubiquiti. As such, the UBNT_TYPE
must match from the "Flashing through factory firmware" install instructions
to work.
Phy0 is QCA988X which can tune either band (2.4 or 5GHz). Phy1 is AR9342,
on which 5GHz is disabled. It isn't currently known whether phy1 is
routed to the N connector at all.
Signed-off-by: Russell Senior <russell@personaltelco.net>
Sungbo Eo [Mon, 4 Jan 2021 13:27:28 +0000 (22:27 +0900)]
kernel: enable CONFIG_LEDS_TRIGGER_HEARTBEAT
The heartbeat trigger is used by luci-mod-system, which is installed
as a part of the standard luci package set. It seems the LED trigger
will be required quite often, so let's enable it by default.
This increases uncompressed kernel size by about 100 bytes on ath79/generic.
Leon M. George [Tue, 12 Jan 2021 09:30:08 +0000 (10:30 +0100)]
hostapd: fix setting wps_state to "not configured"
With encryption disabled, it was intended to set wpa_state=1 (enabled,
not configured) through the 'wps_not_configured' flag.
The flag is set appropriately but the condition using it is broken.
Instead, 'wps_configured' is checked and wpa_state is always 2 (enabled,
configured). Fix it by using the correct variable name.
Fixes: 498d84fc4e00 ("netifd: add wireless configuration support
and port mac80211 to the new framework")
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit title/message improvements] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Sun, 3 Jan 2021 13:40:01 +0000 (22:40 +0900)]
kernel: update kmod-thermal package
CONFIG_THERMAL option was changed to boolean in upstream linux commit 554b3529fe01 ("thermal/drivers/core: Remove the module Kconfig's option").
Switch it to 'y' and remove FILES and AUTOLOAD for non-existant module file.
And update the descripton text for the package as in upstream linux commit eb8504620381 ("thermal: Rephrase the Kconfig text for thermal").
Nick Hainke [Wed, 13 Jan 2021 15:06:03 +0000 (16:06 +0100)]
owipcalc: use v6 in cidr_parse6 function
The cidr_parse6 function parses a string to an ipv6-address.
The cidr struct contains a union called buf for the ipv4 and ipv6
address. Since it is a char pointer and the struct is initialized with
the maximum size (so ipv6 string) it does not make any difference.
However, we should access the buffer using the v6 name, since it could
be confusing otherwise.
Jan Alexander [Thu, 14 Jan 2021 13:55:22 +0000 (14:55 +0100)]
ipq806x: fix Ubiquiti UniFi AC HD partition map
This fixes a typo in the previously committed partition map that led to
the extension of the read-only mtd partition "SSD" into the following
partitions.
Fixes: 4e46beb31342 ("ipq806x: add support for Ubiquiti UniFi AC HD") Signed-off-by: Jan Alexander <jan@nalx.net>
Paul Spooren [Wed, 15 Apr 2020 00:49:54 +0000 (14:49 -1000)]
scripts: target-metadata don't add PROFILES twice
Since 4ee3cf2b5a profiles with alternative vendor names may appear
multiple times in `tmp/.targetinfo` or `.targetinfo` (for
ImageBuilders).
The `target-metadata.pl` script adds these profiles then twice to
`PROFILE_NAMES` and the ImageBuilder show the profile twice when running
`make info`.
This patch removes duplicate profile IDs and only adds them once to
`.profiles.mk`.
Felix Fietkau [Thu, 14 Jan 2021 13:05:58 +0000 (14:05 +0100)]
mt76: update to the latest version
a46f9a9160e9 mt76: mt7915: add vif check in mt7915_update_vif_beacon() 27ad12352ac9 mt76: mt7615: add vif check in mt7615_update_vif_beacon() 0a449cef024e mt76: mt7915: fix MT_CIPHER_BIP_CMAC_128 setkey eacd2d493c61 mt76: mt7915: reset token when mac_reset happens e4b23301e6c9 mt76: mt7615: reset token when mac_reset happens 6e22bbfe0360 mt76: mt7615: convert comma to semicolon 37865118ae2d mt76: mt7915: convert comma to semicolon 742c36b2e527 mt76: mt7915: run mt7915_configure_filter holding mt76 mutex a515727e8423 mt76: mt7915: add support for flash mode b6f7b3da5216 mt76: mt7915: fix endianness warning in mt7915_mcu_set_radar_th 062f3f4f06a2 mt76: mt7915: simplify mt7915_mcu_send_message routine dbba9b993300 mt76: mt7915: drop zero-length packet to avoid Tx hang 36a745d0f71c mt76: Fix queue ID variable types after mcu queue split a4539760b0b1 mt7915: update the testmode support to the latest upstream patch 64bd6f87e4c2 mt7915: fix crash on failure in pci_set_dma_mask c202ace409e0 mt76: remove unused variable q d1b827781f84 mt76: mt7915: add partial add_bss_info command on testmode init a897a69769f5 mt76: testmode: introduce dbdc support b44472e99822 mt76: testmode: move mtd part to mt76_dev 45e27e6cdc12 mt76: mt7915: move testmode data from dev to phy b6673b005770 mt76: mt7615: move testmode data from dev to phy abdd471e9f2d mt76: mt7915: fix ht mcs in mt7915_mcu_get_rx_rate() d679b56b9585 mt76: move mac_work in mt76_core module 36cd48ab4454 mt76: move chainmask in mt76_phy 89a6781ed045 mt76: mt7915: force ldpc for bw larger than 20MHz in testmode 3d0834e78005 mt76: testmode: add support to set user-defined spe index cc05f4679667 mt76: testmode: add attributes for ipg related parameters 77b18b16fe16 mt76: testmode: make tx queued limit adjustable 6365a58573cb mt76: mt7915: split edca update function e56282bf67f6 mt76: mt7915: add support for ipg in testmode 6fa642903e4e mt76: mt7915: calculate new packet length when tx_time is set in testmode 729ec5daeba5 mt76: mt7915: clean hw queue before starting new testmode tx 981443da5cf7 mt76: testmode: add a new state for continuous tx 4793fc9b3d48 mt76: mt7915: rework set state part in testmode 11a1e86e5946 mt76: mt7915: add support for continuous tx in testmode 364affef82fc mt76: mt7615: mt7915: disable txpower sku when testmode enabled 9fc19db51293 mt76: mt7915: simplify peer's TxBF capability check 6377b7f330be mt76: mt7915: add implicit Tx beamforming support 983091a40633 mt76: mt7915: fix MESH ifdef block bbb7a9e77751 mt76: mt76u: fix NULL pointer dereference in mt76u_status_worker a28a8dd2f7de mt76: usb: fix crash on device removal 9c312f2ce2c5 mt76: mt7915: rework mcu API e6fe82acb111 mt76: mt7915: disable RED support in the WA firmware 25d7429bdc41 mt76: mt7915: fix eeprom parsing for DBDC 7a93026dd3dc mt76: mt7915: fix eeprom DBDC band selection 4c8a09cc45d0 tools: Set mode for new file /tmp/mt76-test-%s
Leon M. George [Tue, 12 Jan 2021 08:38:02 +0000 (09:38 +0100)]
hostapd: fix key_mgmt typo
The key_mgmt variable was mistyped when checking against "WPS", so
the if clause was never entered.
Fixes: f5753aae233f ("hostapd: add support for WPS pushbutton station") Signed-off-by: Leon M. George <leon@georgemail.eu>
[add commit message, bump PKG_RELEASE] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Etan Kissling [Wed, 13 Jan 2021 08:52:02 +0000 (09:52 +0100)]
hostapd: add multicast_to_unicast and per_sta_vif
This allows configuration of multicast_to_unicast and per_sta_vif options.
- multicast_to_unicast requests multicast-to-unicast conversion.
- per_sta_vif assigns each station its own AP_VLAN interface.
Etan Kissling [Tue, 12 Jan 2021 23:54:08 +0000 (00:54 +0100)]
nf-conntrack: allow querying conntrack info in nfqueue
This allows libnetfilter_queue to access connection tracking information
by requesting NFQA_CFG_F_CONNTRACK. Connection tracking information is
provided in the NFQA_CT attribute.
CONFIG_NETFILTER_NETLINK_GLUE_CT enables the interaction between
nf_queue and nf_conntrack_netlink. Without this option, trying to access
connection tracking information results in "Operation not supported".
David Bauer [Mon, 7 Dec 2020 03:53:02 +0000 (04:53 +0100)]
zstd: fix package source
It looks like GitHub changed the URL path for release tarballs, thus the
download for the zstd package was always falling back to the OpenWrt
sources mirror.
Fix the GitHub URL for one which works. The file hash remains unchanged.
Jan Alexander [Sat, 9 Jan 2021 10:33:34 +0000 (11:33 +0100)]
uboot-envtools: add support for Aruba AP-303 and AP-365
Both devices use u-boot env variables to boot OpenWrt from its flash
partition. Using u-boot envtools, it is possible to change the bootcmd
back to the stock firmware partition directly from OpenWrt without
attaching a serial cable or even physically accessing the device.
Copy the OpenWrt sysupgrade image to the /tmp directory of the device
using scp. Default IP address is 192.168.1.20 and default username and
password are "ubnt".
SSH to the device and write the bootselect flag to ensure it is booting
from the mtd partition the OpenWrt image will be written to. Verify the
output device below matches mtd partition "bootselect" using /proc/mtd.
Rafał Miłecki [Fri, 8 Jan 2021 12:32:37 +0000 (13:32 +0100)]
bcm4908: initial work on the Broadcom BCM4908 target
BCM4906, BCM4908 and BCM49408 are SoCs with 64 bit ARMv8 B53 CPUs.
Upstream Linux is slowly getting support for that SoCs family so it
makes sense to add target for it.
This prepares initial support for:
1. Asus GT-AC5300
BCM4908 based device (4 CPUs) with 1024 MiB RAM, NAND, 8 LAN ports.
2. Netgear R8000P
BCM4906 based device (2 CPUs) with 512 MiB RAM, NAND, 4 LAN ports.
Flashing info will come later as we learn how to generate proper images.
It isn't usable yet (it only produces a bootable kernel) so "source-only"
is used.
David Bauer [Mon, 11 Jan 2021 04:57:52 +0000 (05:57 +0100)]
rockchip: add missing Kconfig symbols
When compiling with CONFIG_ALL_KMODS enabled, compilation might stall
due to unset rockchip-specific config symbols. Disable these to avoid
stalling this step.
Paul Spooren [Wed, 30 Dec 2020 19:08:17 +0000 (09:08 -1000)]
build/image: warn if missing qemu-img for VDI/VMDK
Currently `qemu-img` is used to convert raw x86 images to VDI and VMDK
images, used for virtual machines.
Having `qemu-img` in tree requires us to maintain an ancient version of
`qemu-utils`, which recently required extra work to compile with newer
compiler version.
This commit prints a warning message in case `qemu-img` is missing.
As a next step the in-tree version of `qemu-img` can be removed.
Daniel Golle [Mon, 7 Dec 2020 13:12:46 +0000 (13:12 +0000)]
hostapd: return PID on config_add call
To simplify the way netifd acquires the PIDs of wpa_supplicant and
hostapd let the config_add method of both of them return the PID of the
called process. Use the returned PID instead of querying procd when
adding wpa_supplicant configuration.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
kernel-defaults: Manage the enabling/disabling of ZSTD
Linux 5.9 introduces support for ZSTD ramdisk and initrd compression,
make sure we enable/disable the relevant options when building an
initramfs enabled kernel.
kernel-defaults: Delete external source tree user_headers
When we use an external kernel tree which may not have been fully
cleaned, there may be user_headers left which do not match the target
architecture, leading to build failures for packages that do an explicit
inclusion of user_headers (such as iproute2 or iptables). Make sure we
delete them while preparing the directory.
Stijn Segers [Fri, 8 Jan 2021 13:32:48 +0000 (14:32 +0100)]
realtek: add support for ZyXEL GS1900-8HP v1 and v2
The ZyXEL GS1900-8HP is an 8 port gigabit switch with PoE+ support.
There are two versions on the market (v1 & v2) which share similar
specs (same flash size and flash layout, same RAM size, same PoE+ power
envelope) but have a different case and board layout that they each
share with other GS1900 siblings.
The v1 seems to share its PCB and case with non-PoE GS1900-8; as such,
adding support for the GS1900-8 would probably be trivial. The v2 seems
to share its casing and platform with its already supported bigger
brother, the GS1900-10HP - its board looks the same, except for two
holes where the GS1900-10 has its SFP ports.
Like their 10 port sibling, both devices have a dual firmware layout.
Both GS1900-8HP boards have the same 70W PoE+ power budget. In order to
manipulate the PoE+, one needs the rtl83xx-poe package [1].
After careful consideration it was decided to go with separate images
for each version.
Specifications (v1)
-------------------
* SoC: Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash: Macronix MX25L12835F 16 MiB
* RAM: Nanya NT5TU128M8HE-AC 128 MiB DDR2 SDRAM
* Ethernet: 8x 10/100/1000 Mbit
* PoE+: Broadcom BCM59111KMLG (IEEE 802.3at-2009 compliant, 2x)
* UART: 1 serial header with populated standard pin connector on the
left side of the PCB, towards the bottom. Pins are labeled:
+ VCC (3.3V)
+ TX
+ RX
+ GND
Specifications (v2)
-------------------
* SoC: Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash: Macronix MX25L12835F 16 MiB
* RAM: Samsung K4B1G0846G 128 MiB DDR3 SDRAM
* Ethernet: 8x 10/100/1000 Mbit
* PoE+: Broadcom BCM59121B0KMLG (IEEE 802.3at-2009 compliant)
* UART: 1 angled serial header with populated standard pin connector
accessible from outside through the ventilation slits on the
side. Pins from top to bottom are clearly marked on the PCB:
+ VCC (3.3V)
+ TX
+ RX
+ GND
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
Instructions are identical to those for the GS1900-10HP and apply both
to the GS1900-8HP v1 and v2 as well.
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only boot off the first partition anyway (hardcoded in the DTS). To
make sure we are manipulating the first partition, issue the following
commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8hp-v{1,2}-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp//tmp/openwrt-realtek-generic-zyxel_gs1900-8hp-v{1,2}-squashfs-sysupgrade.bin
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[merge PoE case, keep device definitions separate, change all those
hashes in the commit message to something else so they don't get
removed when changing the commit ...] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Stijn Segers [Fri, 8 Jan 2021 13:32:47 +0000 (14:32 +0100)]
realtek: introduce shared DTSI for GS1900 series
The ZyXEL GS1900-8HP v1, v2 and GS1900-10HP are all built on a similar
Realtek RTL8380M platform. Create a common DTSI in preparation for
GS1900-8HP support, and switch to the macros defined in rtl838x.dtsi.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[drop redundant includes, use &mdio directly, do not replace SFP
ports] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Pawel Dembicki [Mon, 4 Jan 2021 16:59:30 +0000 (17:59 +0100)]
kernel: add hid-cp2112 driver support
This patch adds kernel module for Silicon Labs CP2112 HID USB to SMBus
Master Bridge. This is a HID device driver which registers as an i2c
adapter and gpiochip to expose these functions of the CP2112.
Michael Pratt [Fri, 1 Jan 2021 22:08:34 +0000 (17:08 -0500)]
ath79: make Engenius fakeroot partitions read-only
For:
- ENH202 v1
- ENS202EXT v1
These boards were committed before it was discovered
that for all Engenius boards with a "failsafe" image,
forcing the failsafe image to load next boot
can be achieved by editing the u-boot environment like:
`fw_setenv rootfs_checksum 0`
So it's not necessary to delete a partition to boot to failsafe image.
Michael Pratt [Fri, 1 Jan 2021 21:48:52 +0000 (16:48 -0500)]
ath79: move small-flash Engenius boards to tiny
This moves some of the Engenius boards from generic to tiny:
- EAP350 v1
- ECB350 v1
- ENH202 v1
For these, factory.bin builds are already failing on master
branch because of the unique situation for these boards:
- 8 MB flash
- an extra "failsafe" image for recovery
- TFTP does not work (barely possible with 600 MTU)
- bootloader loads image from a longer flash offset
- 1 eraseblock each needed for OKLI kernel loader and fake rootfs
- using mtd-concat to make use of remaining space...
The manual alternative would be removing the failsafe partition.
However this comes with the risk of extremely difficult recovery
if a flash ever fails because TFTP on the bootloader is bugged. Signed-off-by: Michael Pratt <mcpratt@pm.me>
[improve commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sven Wegener [Fri, 1 Jan 2021 11:27:33 +0000 (12:27 +0100)]
tools/cmake: always use non-ccache CC and CXX variables
cmake is a dependency of ccache, which means it is build before ccache
is available and hence must be build with non-ccache CC and CXX. It
currently works, because the cmake build system splits the compiler
variable and treats them as multiple compilers to check.
For "ccache gcc" it first tests for "ccache", which always fails,
because ccache is not a compiler by itself, even if it is available, and
then ends up calling "gcc" alone, effectively never using ccache.
Let's make this explicit by forcing the use of non-ccache CC and CXX.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Sven Wegener [Fri, 1 Jan 2021 10:46:04 +0000 (11:46 +0100)]
build: use ccache -C for cleaning the cache
This keeps the configuration, like the size of the cache, and the
statistics intact. Move the removal of the cache directory to the
distclean target, but only delete the .ccache directory inside of our
build tree, as we should not mess with a user-configured external ccache
directory this destructively.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Daniel Golle [Tue, 5 Jan 2021 20:02:52 +0000 (20:02 +0000)]
rpcd: update to git HEAD
fd017ba iwinfo: add ht and vht operation info to wifi scan 4c66b31 iwinfo: export center channel for info ubus call e28d4a5 iwinfo: add support for 802.11ad and GCMP 5c15f57 iwinfo: return hwmode 'ad' on 802.11ad-only hardware ea7f471 iwinfo: include ht_operation data only if available
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Jo-Philipp Wich [Wed, 6 Jan 2021 22:26:15 +0000 (23:26 +0100)]
iwinfo: improve ABI version handling and bump to git HEAD
- Encode ABI version in compiled shared object file
- Only ship versioned shared library
a17f561 iwinfo: detect QCA IPQ4019 WiSoC from FDT ea28dfb iwinfo: export ht and vht operation in scan results 4e22953 iwinfo: export center_chan info for local wifi 74d13fb cli: account for additional digit for frequencies above 10GHz 8bfd8d8 iwinfo: add support for GCMP cipher 618c1e8 iwinfo: add hardware description for QCA MIPS WiSoCs 0702f32 iwinfo: improve center channel handling 51c1336 iwinfo: set center chan unsupported for not-nl80211 driver 23d2722 build: add ability to specify shared object version
Signed-off-by: Jo-Philipp Wich <jo@mein.io> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Paul Spooren [Sun, 27 Dec 2020 21:26:37 +0000 (11:26 -1000)]
scripts/feed: no warn on toolchain/linux overwrite
The recent 7f285d "scripts/feeds: warn when skipping core package
override" floods SDK output with warning of overwriting "linux" and
"toolchain" core packages. This should be ignored as these are not
regular packages added via feeds.
Strictly, an SPDX identifier requires a space between the comment
marker and the identifier itself. This has been addressed in b69c21738e29 ("treewide: add space before SPDX identifier"), but
some new malformatted identifiers were merged recently.
This could have been prevented by using checkpatch.pl earlier.
Fixes: 1a775a4fd033 ("ipq806x: add support for TP-Link Talon AD7200") Fixes: 8ddaeaf6424e ("ipq806x: create DTSI for TP-Link AD7200 and C2600") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ipq806x: improve model name and revision for TP-Link AD7200
The TP-Link AD7200 appears with and without the "Talon" model name
prefix. Let's use both variants for 'make menuconfig' so everybody
can locate the device.
Concerning the revision, the TP-Link page lists v1 and v2 with the
device currently marked as "End of Life". However, the v2 and latest
v1 firmware are byte-identical. Thus, we only need one image for
this device and do not need to include the revision in the image name.
While at it, remove the useless BOARD_NAME variable which only makes
sense in combination with upgrade from legacy stable versions or when
custom upgrade scripts are involved.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Both devices share most of their setup except buttons and LEDs,
so having a common DTSI removes a lot of duplicate code.
In order to have a shared partitioning scheme, device-id and
product-info from AD7200 have been merged into a single
product-info partition like for C2600.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
David Bauer [Tue, 5 Jan 2021 23:00:01 +0000 (00:00 +0100)]
ramips: limit 5GHz channels for UniFi 6 Lite
The MT7915 radio currently advertises 2.4GHz channels while the antenna
path only supports 5 GHz. Limit the radio to 5GHz channels to prevent
users from configuring non-supported channels.
Daniel Golle [Tue, 5 Jan 2021 20:02:52 +0000 (20:02 +0000)]
rpcd: update to git HEAD
fd017ba iwinfo: add ht and vht operation info to wifi scan 4c66b31 iwinfo: export center channel for info ubus call e28d4a5 iwinfo: add support for 802.11ad and GCMP 5c15f57 iwinfo: return hwmode 'ad' on 802.11ad-only hardware
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 5 Jan 2021 20:04:22 +0000 (20:04 +0000)]
iwinfo: update to git HEAD
a17f561 iwinfo: detect QCA IPQ4019 WiSoC from FDT ea28dfb iwinfo: export ht and vht operation in scan results 4e22953 iwinfo: export center_chan info for local wifi 74d13fb cli: account for additional digit for frequencies above 10GHz 8bfd8d8 iwinfo: add support for GCMP cipher
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Syrone Wong [Fri, 1 Jan 2021 13:50:43 +0000 (21:50 +0800)]
tools/fakeroot: update to 1.25.3
use PKG_FIXUP:=autoreconf to generate configure
200-hide-dlsym-error.patch deleted due to fixed upstream in another way
other patches refreshed to reflect latest changes
Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
7. Reboot the device. It should boot into OpenWrt.
Below are the original installation instructions prior to the discovery
of "devmode=TRUE". They are not required for installation and are
documentation only.
The bootloader employs signature verification on the FIT image
configurations. This way, booting unauthorized image without patching
the bootloader is not possible. Manually configuring the bootcmd in the
U-Boot envronment won't work, as this is restored to the default value
if modified.
The bootloader is made up of three different parts.
1. The SPL performing early board initialization and providing a XModem
recovery in case the PBL is missing
2. The PBL being the primary U-Boot application and containing the
control FDT. It is LZMA packed with a uImage header.
3. A Ubiquiti standalone U-Boot application providing the main boot
routine as well as their recovery mechanism.
In a perfect world, we would only replace the PBL, as the SPL does not
perform checks on the PBLs integrity. However, as the PBL is in the same
eraseblock as the SPL, we need to at least rewrite both.
The bootloader will only verify integrity in case it has a "signature"
node in it's control device-tree. Renaming the signature node to
something else will prevent this from happening.
Warning: These instructions are based on the firmware intially
shipped with the device and potentially brick your device in a way it
can only be recovered using a SPI flasher.
Only (!) proceed if you understand this!
1. Extract the bootloader from the U-Boot partition using the OpenWrt
initramfs image.
5. Open the decompressed PBL using your favorite hexeditor. Locate the
control FDT at offset 0x4CED0 (0xD00DFEED). At offset 0x4D5BC, the
label for the signature node is located. Rename the "signature"
string at this offset to "signaturr".
Daniel Golle [Tue, 5 Jan 2021 12:55:34 +0000 (12:55 +0000)]
ipq806x: some corrections for TP-Link Talon AD7200
Address most comments made by Adrian Schmutzler on the mailing list.
The device name is kept as 'TP-Link Talon AD7200' as that seems to be
the marketing name TP-Link chose for that device, it also matches the
naming scheme for other TP-Link devices (e.g. 'TP-Link Archer C7').
Fixes: 1a775a4fd0 ("ipq806x: add support for TP-Link Talon AD7200") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Talon AD7200 is basically an Archer C2600 with a third PCIe lane
and an 802.11ad radio. It looks like the Archers C2600/5400 but the
housing is slightly larger.
Robert Marko [Wed, 18 Sep 2019 17:54:56 +0000 (19:54 +0200)]
linux-firmware: Add wil6210 firmware
This patch adds wil6210 firmware and board files.
Firmware version is not up to date but is only freely redistributable one I found.
Board file is a generic one so most devices and especially those for long distance
PtP links will require so in a ipq-wifi like way.
Robert Marko [Sun, 17 Mar 2019 20:01:17 +0000 (21:01 +0100)]
hostapd: wpa_supplicant: Enable proper GCMP cipher support
This patch enables hostapd.sh to properly configure wpa_supplicant
for when GCMP is used as cipher in station mode.
Without this wpa_supplicant will be unable to connect to AP.
This is needed for wil6210 as it does not support CCMP.
projects / thirdparty / openwrt.git / log
