Laptop with Turks/Thames GPU will freeze if dpm is enabled. It seems
the SMC engine is relying on some state inside the CP engine. CP needs
to chew at least one packet for it to get in good state for dynamic
power management.
This patch simply disabled and re-enable DPM after the ring test which
is enough to avoid the freeze.
Passive DP->DVI/HDMI dongles on DP++ ports show up to the system as HDMI
devices, as they do not have a sink device in them to respond to any AUX
traffic. When probing these dongles over the DDC, sometimes they will
NAK the first attempt even though the transaction is valid and they
support the DDC protocol. The retry loop inside of
drm_do_probe_ddc_edid() would normally catch this case and try the
transaction again, resulting in success.
drm: give up on edid retries when i2c bus is not responding
This added code to exit immediately if the return code from the
i2c_transfer function was -ENXIO in order to reduce the amount of time
spent in waiting for unresponsive or disconnected devices. That was
possible because the underlying i2c bit banging algorithm had retries of
its own (which, of course, were part of the reason for the bug the
commit fixes).
we've been flipping back and forth enabling the GMBUS transfers, but
we've settled since then. The GMBUS implementation does not do any
retries, however, bailing out of the drm_do_probe_ddc_edid() retry loop
on first encounter of -ENXIO. This, combined with Eugeni's commit, broke
the retry on -ENXIO.
Retry GMBUS once on -ENXIO on first message to mitigate the issues with
passive adapters.
This patch is based on the work, and commit message, by Todd Previte
<tprevite@gmail.com>.
Apparently we can have requests even if though the active list is empty,
so do the request retirement regardless of whether there's anything
on the active list.
The way it happened here is that during suspend intel_ring_idle()
notices the olr hanging around and then proceeds to get rid of it by
adding a request. However since there was nothing on the active lists
i915_gem_retire_requests() didn't clean those up, and so the idle work
never runs, and we leave the GPU "busy" during suspend resulting in a
WARN later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the HSW b-spec we need to try clock divisors of 63
and 72, each 3 or more times, when attempting DP AUX channel
communication on a server chipset. This actually wasn't happening
due to a short-circuit that only checked the DP_AUX_CH_CTL_DONE bit
in status rather than checking that the operation was done and
that DP_AUX_CH_CTL_TIME_OUT_ERROR was not set.
[v2] Implemented alternate solution suggested by Jani Nikula.
Signed-off-by: Jim Bride <jim.bride@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid entering "RTC-only mode" at poweroff. It is unsupported by most
versions of BeagleBone, and risks hardware damage.
The damaging configuration is having system-power-controller
without ti,pmic-shutdown-controller.
Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com> Tested-by: Matthijs van Duin <matthijsvanduin@gmail.com> Signed-off-by: Robert Nelson <robertcnelson@gmail.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Felipe Balbi <balbi@ti.com> Cc: Johan Hovold <johan@kernel.org>
[Matthijs van Duin: added explanatory comments] Signed-off-by: Matthijs van Duin <matthijsvanduin@gmail.com> Fixes: http://bugs.elinux.org/issues/143
[tony@atomide.com: updated comments with the hardware breaking info] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The subtraction here was using a signed integer and did not have any
bounds checking at all. This commit adds proper bounds checking, made
easy by use of an unsigned integer. This way, a single packet won't be
able to remotely trigger a massive loop, locking up the system for a
considerable amount of time. A PoC follows below, which requires
ozprotocol.h from this module.
static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}
int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}
uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}
int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Acked-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A network supplied parameter was not checked before division, leading to
a divide-by-zero. Since this happens in the softirq path, it leads to a
crash. A PoC follows below, which requires the ozprotocol.h file from
this module.
static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}
int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}
uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}
int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Acked-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using signed integers, the subtraction between required_size and offset
could wind up being negative, resulting in a memcpy into a heap buffer
with a negative length, resulting in huge amounts of network-supplied
data being copied into the heap, which could potentially lead to remote
code execution.. This is remotely triggerable with a magic packet.
A PoC which obtains DoS follows below. It requires the ozprotocol.h file
from this module.
static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}
int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}
uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}
int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Acked-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since elt->length is a u8, we can make this variable a u8. Then we can
do proper bounds checking more easily. Without this, a potentially
negative value is passed to the memcpy inside oz_hcd_get_desc_cnf,
resulting in a remotely exploitable heap overflow with network
supplied data.
This could result in remote code execution. A PoC which obtains DoS
follows below. It requires the ozprotocol.h file from this module.
static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}
int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}
uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}
int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Acked-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 334c86c494b9 ("MIPS: IRQ: Add stackoverflow detection") added
kernel stack overflow detection, however it only enabled it conditional
upon the preprocessor definition DEBUG_STACKOVERFLOW, which is never
actually defined. The Kconfig option is called DEBUG_STACKOVERFLOW,
which manifests to the preprocessor as CONFIG_DEBUG_STACKOVERFLOW, so
switch it to using that definition instead.
Due to a typo the illegal access interrupt is never cleared in by
the interupt handler, causing an effective deadlock on the first
illegal access.
This was broken since the code was introduced in 5433acd81e87 ("MIPS:
ralink: add illegal access driver"), but only exposed when the Kconfig
symbol was added, thus enabling the code.
Fixes: a7b7aad383c ("MIPS: ralink: add missing symbol for RALINK_ILL_ACC") Signed-off-by: Jonas Gorski <jogo@openwrt.org> Cc: linux-mips@linux-mips.org Cc: John Crispin <blogic@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/10172/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The early_idt_handlers asm code generates an array of entry
points spaced nine bytes apart. It's not really clear from that
code or from the places that reference it what's going on, and
the code only works in the first place because GAS never
generates two-byte JMP instructions when jumping to global
labels.
Clean up the code to generate the correct array stride (member size)
explicitly. This should be considerably more robust against
screw-ups, as GAS will warn if a .fill directive has a negative
count. Using '. =' to advance would have been even more robust
(it would generate an actual error if it tried to move
backwards), but it would pad with nulls, confusing anyone who
tries to disassemble the code. The new scheme should be much
clearer to future readers.
While we're at it, improve the comments and rename the array and
common code.
Binutils may start relaxing jumps to non-weak labels. If so,
this change will fix our build, and we may need to backport this
change.
Fixed regression. After commit 29e409f0f761 ("xhci: Allow xHCI drivers to
be built as separate modules") the module xhci_hcd became non-removable.
That behaviour is not expected and there're no notes about it in commit
message. The module should be removable as it blocks PM suspend/resume
functions (Debian Bug#666406).
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com> Reviewed-by: Andrew Bresticker <abrestic@chromium.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Regression in commit 638139eb95d2 ("usb: hub: allow to process more usb
hub events in parallel")
The regression resulted in intermittent failure to initialise a 10-port
hub (with three internal VL812 4-port hub controllers) on boot, with a
failure rate of around 8%, due to multiple race conditions when
accessing addr_dev and slot_id in struct xhci_hcd.
This regression also exposed a problem with xhci_setup_device, which
"should be protected by the usb_address0_mutex" but no longer is due to
commit 6fecd4f2a58c ("USB: separate usb_address0 mutexes for each bus")
With separate buses (and locks) it is no longer the case that a single
lock will protect xhci_setup_device from accesses by two parallel
threads processing events on the two buses.
Fix this by adding a mutex to protect addr_dev and slot_id in struct
xhci_hcd, and by making the assignment of slot_id atomic.
Fixes multiple boot errors:
[ 0.583008] xhci_hcd 0000:00:14.0: Bad Slot ID 2
[ 0.583009] xhci_hcd 0000:00:14.0: Could not allocate xHCI USB device data structures
[ 0.583012] usb usb1-port3: couldn't allocate usb_device
And:
[ 0.637409] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
[ 0.637417] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
[ 0.637421] usb usb1-port1: couldn't allocate usb_device
And:
[ 0.753372] xhci_hcd 0000:00:14.0: ERROR: unexpected setup context command completion code 0x0.
[ 0.753373] usb 1-3: hub failed to enable device, error -22
[ 0.753400] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
[ 0.753402] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
[ 0.753403] usb usb1-port3: couldn't allocate usb_device
And:
[ 11.018386] usb 1-3: device descriptor read/all, error -110
And:
[ 5.753838] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
Tested with 200 reboots, resulting in no USB hub init related errors.
Fixes: 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel") Link: https://lkml.kernel.org/g/CAP-bSRb=A0iEYobdGCLpwynS7pkxpt_9ZnwyZTPVAoy0Y=Zo3Q@mail.gmail.com Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
[changed git commit description style for checkpatch -Mathias] Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added the USB serial device ID for the HubZ dual ZigBee
and Z-Wave radio dongle.
Signed-off-by: John D. Blair <johnb@candicontrols.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bdi_unregister() now contains very little functionality.
It contains a "WARN_ON" if bdi->dev is NULL. This warning is of no
real consequence as bdi->dev isn't needed by anything else in the function,
and it triggers if
blk_cleanup_queue() -> bdi_destroy()
is called before bdi_unregister, which happens since
Commit: 6cd18e711dd8 ("block: destroy bdi before blockdev is unregistered.")
So this isn't wanted.
It also calls bdi_set_min_ratio(). This needs to be called after
writes through the bdi have all been flushed, and before the bdi is destroyed.
Calling it early is better than calling it late as it frees up a global
resource.
Calling it immediately after bdi_wb_shutdown() in bdi_destroy()
perfectly fits these requirements.
So bdi_unregister() can be discarded with the important content moved to
bdi_destroy(), as can the
writeback_bdi_unregister
event which is already not used.
Reported-by: Mike Snitzer <snitzer@redhat.com> Fixes: c4db59d31e39 ("fs: don't reassign dirty inodes to default_backing_dev_info") Fixes: 6cd18e711dd8 ("block: destroy bdi before blockdev is unregistered.") Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Dan Williams <dan.j.williams@intel.com> Tested-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com> Signed-off-by: NeilBrown <neilb@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
=================================
[ INFO: inconsistent lock state ]
4.1.0-rc7+ #217 Tainted: G O
---------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
swapper/6/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
(ext_devt_lock){+.?...}, at: [<ffffffff8143a60c>] blk_free_devt+0x3c/0x70
{SOFTIRQ-ON-W} state was registered at:
[<ffffffff810bf6b1>] __lock_acquire+0x461/0x1e70
[<ffffffff810c1947>] lock_acquire+0xb7/0x290
[<ffffffff818ac3a8>] _raw_spin_lock+0x38/0x50
[<ffffffff8143a07d>] blk_alloc_devt+0x6d/0xd0 <-- take the lock in process context
[..]
[<ffffffff810bf64e>] __lock_acquire+0x3fe/0x1e70
[<ffffffff810c00ad>] ? __lock_acquire+0xe5d/0x1e70
[<ffffffff810c1947>] lock_acquire+0xb7/0x290
[<ffffffff8143a60c>] ? blk_free_devt+0x3c/0x70
[<ffffffff818ac3a8>] _raw_spin_lock+0x38/0x50
[<ffffffff8143a60c>] ? blk_free_devt+0x3c/0x70
[<ffffffff8143a60c>] blk_free_devt+0x3c/0x70 <-- take the lock in softirq
[<ffffffff8143bfec>] part_release+0x1c/0x50
[<ffffffff8158edf6>] device_release+0x36/0xb0
[<ffffffff8145ac2b>] kobject_cleanup+0x7b/0x1a0
[<ffffffff8145aad0>] kobject_put+0x30/0x70
[<ffffffff8158f147>] put_device+0x17/0x20
[<ffffffff8143c29c>] delete_partition_rcu_cb+0x16c/0x180
[<ffffffff8143c130>] ? read_dev_sector+0xa0/0xa0
[<ffffffff810e0e0f>] rcu_process_callbacks+0x2ff/0xa90
[<ffffffff810e0dcf>] ? rcu_process_callbacks+0x2bf/0xa90
[<ffffffff81067e2e>] __do_softirq+0xde/0x600
Neil sees this in his tests and it also triggers on pmem driver unbind
for the libnvdimm tests. This fix is on top of an initial fix by Keith
for incorrect usage of mutex_lock() in this path: 2da78092dda1 "block:
Fix dev_t minor allocation lifetime". Both this and 2da78092dda1 are
candidates for -stable.
Fixes: 2da78092dda1 ("block: Fix dev_t minor allocation lifetime") Cc: Keith Busch <keith.busch@intel.com> Reported-by: NeilBrown <neilb@suse.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some v7 devices (e.g. Lenovo-E550) the deltas reported are typically
only in the 0-1 range dividing this by 2 results in a range of 0-0.
And even for v7 devices where this does not lead to making the trackstick
entirely unusable, it makes it twice as slow as before we added v7 support
and were using the ps/2 mouse emulation of the dual point setup.
If some kind of generic slowdown is actually necessary for some devices,
then that belongs in userspace, not in the kernel.
Reported-and-tested-by: Rico Moorman <rico.moorman@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using _bh variant for spin locks causes this kind of warning:
Starting logging: ------------[ cut here ]------------
WARNING: CPU: 0 PID: 3 at /ssd_drive/linux/kernel/softirq.c:151
__local_bh_enable_ip+0xe8/0xf4()
Modules linked in:
CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 4.1.0-rc2+ #94
Hardware name: Atmel SAMA5
[<c0013c04>] (unwind_backtrace) from [<c00118a4>] (show_stack+0x10/0x14)
[<c00118a4>] (show_stack) from [<c001bbcc>]
(warn_slowpath_common+0x80/0xac)
[<c001bbcc>] (warn_slowpath_common) from [<c001bc14>]
(warn_slowpath_null+0x1c/0x24)
[<c001bc14>] (warn_slowpath_null) from [<c001e28c>]
(__local_bh_enable_ip+0xe8/0xf4)
[<c001e28c>] (__local_bh_enable_ip) from [<c01fdbd0>]
(at_xdmac_device_terminate_all+0xf4/0x100)
[<c01fdbd0>] (at_xdmac_device_terminate_all) from [<c02221a4>]
(atmel_complete_tx_dma+0x34/0xf4)
[<c02221a4>] (atmel_complete_tx_dma) from [<c01fe4ac>]
(at_xdmac_tasklet+0x14c/0x1ac)
[<c01fe4ac>] (at_xdmac_tasklet) from [<c001de58>]
(tasklet_action+0x68/0xb4)
[<c001de58>] (tasklet_action) from [<c001dfdc>]
(__do_softirq+0xfc/0x238)
[<c001dfdc>] (__do_softirq) from [<c001e140>] (run_ksoftirqd+0x28/0x34)
[<c001e140>] (run_ksoftirqd) from [<c0033a3c>]
(smpboot_thread_fn+0x138/0x18c)
[<c0033a3c>] (smpboot_thread_fn) from [<c0030e7c>] (kthread+0xdc/0xf0)
[<c0030e7c>] (kthread) from [<c000f480>] (ret_from_fork+0x14/0x34)
---[ end trace b57b14a99c1d8812 ]---
It comes from the fact that devices can called some code from the DMA
controller with irq disabled. _bh variant is not intended to be used in
this case since it can enable irqs. Switch to irqsave/irqrestore variant to
avoid this situation.
Rework slave configuration part in order to more report wrong errors
about the configuration.
Only maxburst and addr width values are checked when doing the slave
configuration. The validity of the channel configuration is done at
prepare time.
Some drivers implement only pause operation (no resuming). Example is
pl330 where pause is needed for getting residuum. pl330 does not support
resume operation, transfer must be stopped after pause.
However for slaves this is exposed always as "pause and resume" which
introduces subtle errors on Odroid U3 board (Exynos4412 with pl330).
After adding pause function to pl330 driver the audio playback
(utilizing DMA) gets choppy after some time (approximately 24 hours).
Fix this by exposing "cmd_pause" if and only if pause and resume are
implemented.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Reported-by: gabriel@unseen.is Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: 88987d2c7534 ("dmaengine: pl330: add DMA_PAUSE feature") Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pl330 device could hang infinitely on certain boards when DMA
channels are terminated.
It was caused by lack of runtime resume when executing
pl330_terminate_all() which calls the _stop() function. _stop() accesses
device register and can loop infinitely while checking for device state.
The hang was confirmed by Dinh Nguyen on Altera SOCFPGA Cyclone V
board during boot. It can be also triggered with:
The driver worked around an error in the MAYA44 USB(+)'s mixer unit
descriptor by aborting before parsing the missing field. However,
aborting parsing too early prevented parsing of the other units
connected to this unit, so the capture mixer controls would be missing.
Fix this by moving the check for this descriptor error after the parsing
of the unit's input pins.
message every time playback starts. While USB DAC in the RR2150
supports reading the sample rate, it never returns a sample rate
other than zero in my observation with common sample rates.
Signed-off-by: Eric Wong <normalperson@yhbt.net> Cc: Joe Turner <joe@oampo.co.uk> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb 7-1: New USB device found, idVendor=046d, idProduct=08ca
...
usb 7-1: Warning! Unlikely big volume range (=3072), cval->res is probably wrong.
usb 7-1: [5] FU [Mic Capture Volume] ch = 1, val = 4608/7680/1
When we use 'intel_iommu=igfx_off' to disable translation for the
graphics, and when we discover that the BIOS has misconfigured the DMAR
setup for I/OAT, we use a special DUMMY_DEVICE_DOMAIN_INFO value in
dev->archdata.iommu to indicate that translation is disabled.
With passthrough mode, we were attempting to dereference that as a
normal pointer to a struct device_domain_info when setting up an
identity mapping for the affected device.
This fixes the problem by making device_to_iommu() explicitly check for
the special value and indicate that no IOMMU was found to handle the
devices in question.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c875d2c1 ("iommu/vt-d: Exclude devices using RMRRs from IOMMU API
domains") prevents certain options for devices with RMRRs. This even
prevents those devices from getting a 1:1 mapping with 'iommu=pt',
because we don't have the code to handle *preserving* the RMRR regions
when moving the device between domains.
There's already an exclusion for USB devices, because we know the only
reason for RMRRs there is a misguided desire to keep legacy
keyboard/mouse emulation running in some theoretical OS which doesn't
have support for USB in its own right... but which *does* enable the
IOMMU.
Add an exclusion for graphics devices too, so that 'iommu=pt' works
there. We should be able to successfully assign graphics devices to
guests too, as long as the initial handling of stolen memory is
reconfigured appropriately. This has certainly worked in the past.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 32f13521ca68bc624ff6effc77f308a52b038bf0
("n_tty: Line copy to user buffer in canonical mode")
changed cannonical mode copying to use copy_to_user
but missed adding the call to the audit framework.
Add in the appropriate functions to get audit support.
Fixes: 32f13521ca68 ("n_tty: Line copy to user buffer in canonical mode") Reported-by: Miloslav Trmač <mitr@redhat.com> Signed-off-by: Laura Abbott <labbott@fedoraproject.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some simulators like GEM5, caches may not be simulated. In those
cases, the cache levels and leaves will be zero and will result in
following exception:
kcalloc(0) returns a special value ZERO_SIZE_PTR which is non-NULL value
but results in fault only on any attempt to dereferencing it. So
checking for the non-NULL pointer will not suffice.
This patch checks for non-zero cache leaf nodes and returns error if
there are no cache leaves in detect_cache_attributes.
Cc: Will Deacon <will.deacon@arm.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reported-by: William Wang <william.wang@arm.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The adis16448, unlike the other chips in this family, in addition to the
hardware channels also sends out the DIAG_STAT register in burst mode
before them. Handle that case by skipping over the first 2 bytes before we
pass the received data to the buffer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Fixes: 76ada52f7f5d ("iio:adis16400: Add support for the adis16448") Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few issues with the burst mode support. For one we don't setup
the rx buffer, so the buffer will never be filled and all samples will read
as the zero. Furthermore the tx buffer has the wrong type, which means the
driver sends the wrong command and not the right data is returned.
The final issue is that in burst mode all channels are transferred. Hence
the length of the transfer length should be the number of hardware
channels * 2 bytes. Currently the driver uses indio_dev->scan_bytes for
this. But if the timestamp channel is enabled the scan_bytes will be larger
than the burst length. Fix this by just calculating the burst length based
on the number of hardware channels.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Fixes: 5eda3550a3cc ("staging:iio:adis16400: Preallocate transfer message") Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We unfortunately can't use ~0UL for the scan mask to indicate that the
only valid scan mask is all channels selected. The IIO core needs the exact
mask to work correctly and not a super-set of it. So calculate the masked
based on the channels that are available for a particular device.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Fixes: 5eda3550a3cc ("staging:iio:adis16400: Preallocate transfer message") Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, the two voltage channels had the same ID, which didn't cause
conflicts in sysfs only because one channel is named and the other isn't;
this is still violating the spec though, two indexed channels should never
have the same index.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the scale for the pressure channel, which is currently missing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Fixes: 76ada52f7f5d ("iio:adis16400: Add support for the adis16448") Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove extra space between platform prefix and DRIVER_NAME in MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
br_fdb_update() can be called in process context in the following way:
br_fdb_add() -> __br_fdb_add() -> br_fdb_update() (if NTF_USE flag is set)
so we need to disable softirqs because there are softirq users of the
hash_lock. One easy way to reproduce this is to modify the bridge utility
to set NTF_USE, enable stp and then set maxageing to a low value so
br_fdb_cleanup() is called frequently and then just add new entries in
a loop. This happens because br_fdb_cleanup() is called from timer/softirq
context. The spin locks in br_fdb_update were _bh before commit f8ae737deea1
("[BRIDGE]: forwarding remove unneeded preempt and bh diasables")
and at the time that commit was correct because br_fdb_update() couldn't be
called from process context, but that changed after commit: 292d1398983f ("bridge: add NTF_USE support")
Using local_bh_disable/enable around br_fdb_update() allows us to keep
using the spin_lock/unlock in br_fdb_update for the fast-path.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Fixes: 292d1398983f ("bridge: add NTF_USE support") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several places in the driver (all in control paths) where
coherent dma memory is being allocated using either dma_alloc_coherent()
or the deprecated pci_alloc_consistent(). All these calls should be
changed to use dma_zalloc_coherent() to avoid uninitialized fields in
data structures backed by this memory.
Reported-by: Joerg Roedel <jroedel@suse.de> Tested-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
421b3885bf6d56391297844f43fb7154a6396e12 "udp: ipv4: Add udp early
demux" introduced a regression that allowed sockets bound to INADDR_ANY
to receive packets from multicast groups that the socket had not joined.
For example a socket that had joined 224.168.2.9 could also receive
packets from 225.168.2.9 despite not having joined that group if
ip_early_demux is enabled.
Fix this by calling ip_check_mc_rcu() in udp_v4_early_demux() to verify
that the multicast packet is indeed ours.
Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com> Reported-by: Yurij M. Plotnikov <Yurij.Plotnikov@oktetlabs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we come to tear things down in netback_remove() and generate the
uevent it is possible that the xenstore directory has already been
removed (details below).
In such cases netback_uevent() won't be able to read the hotplug
script and will write a xenstore error node.
A recent change to the hypervisor exposed this race such that we now
sometimes lose it (where apparently we didn't ever before).
Instead read the hotplug script configuration during setup and use it
for the lifetime of the backend device.
The apparently more obvious fix of moving the transition to
state=Closed in netback_remove() to after the uevent does not work
because it is possible that we are already in state=Closed (in
reaction to the guest having disconnected as it shutdown). Being
already in Closed means the toolstack is at liberty to start tearing
down the xenstore directories. In principal it might be possible to
arrange to unregister the device sooner (e.g on transition to Closing)
such that xenstore would still be there but this state machine is
fragile and prone to anger...
A modern Xen system only relies on the hotplug uevent for driver
domains, when the backend is in the same domain as the toolstack it
will run the necessary setup/teardown directly in the correct sequence
wrt xenstore changes.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linux 3.17 and earlier are explicitly engineered so that if the app
doesn't specifically request a CC module on a listener before the SYN
arrives, then the child gets the system default CC when the connection
is established. See tcp_init_congestion_control() in 3.17 or earlier,
which says "if no choice made yet assign the current value set as
default". The change ("net: tcp: assign tcp cong_ops when tcp sk is
created") altered these semantics, so that children got their parent
listener's congestion control even if the system default had changed
after the listener was created.
This commit returns to those original semantics from 3.17 and earlier,
since they are the original semantics from 2007 in 4d4d3d1e8 ("[TCP]:
Congestion control initialization."), and some Linux congestion
control workflows depend on that.
In summary, if a listener socket specifically sets TCP_CONGESTION to
"x", or the route locks the CC module to "x", then the child gets
"x". Otherwise the child gets current system default from
net.ipv4.tcp_congestion_control. That's the behavior in 3.17 and
earlier, and this commit restores that.
Fixes: 55d8694fa82c ("net: tcp: assign tcp cong_ops when tcp sk is created") Cc: Florian Westphal <fw@strlen.de> Cc: Daniel Borkmann <dborkman@redhat.com> Cc: Glenn Judd <glenn.judd@morganstanley.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have two problems in UDP stack related to bogus checksums :
1) We return -EAGAIN to application even if receive queue is not empty.
This breaks applications using edge trigger epoll()
2) Under UDP flood, we can loop forever without yielding to other
processes, potentially hanging the host, especially on non SMP.
This patch is an attempt to make things better.
We might in the future add extra support for rt applications
wanting to better control time spent doing a recv() in a hostile
environment. For example we could validate checksums before queuing
packets in socket receive queue.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sctp_v4_map_v6 was subtly writing and reading from members
of a union in a way the clobbered data it needed to read before
it read it.
Zeroing the v6 flowinfo overwrites the v4 sin_addr with 0, meaning
that every place that calls sctp_v4_map_v6 gets ::ffff:0.0.0.0 as the
result.
Reorder things to guarantee correct behaviour no matter what the
union layout is.
This impacts user space clients that open an IPv6 SCTP socket and
receive IPv4 connections. Prior to 299ee user space would see a
sockaddr with AF_INET and a correct address, after 299ee the sockaddr
is AF_INET6, but the address is wrong.
Fixes: 299ee123e198 (sctp: Fixup v4mapped behaviour to comply with Sock API) Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For mq qdisc, we add per tx queue qdisc to root qdisc
for display purpose, however, that happens too early,
before the new dev->qdisc is finally set, this causes
q->list points to an old root qdisc which is going to be
freed right before assigning with a new one.
Fix this by moving ->attach() after setting dev->qdisc.
For long term, we probably need to clean up the qdisc_graft() code
in case it hides other bugs like this.
Fixes: 95dc19299f74 ("pkt_sched: give visibility to mq slave qdiscs") Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e9ce7cb6b107 ("xen-netback: Factor queue-specific data into queue
struct") introduced a regression when moving queue-specific data into
the queue struct by failing to set the credit_bytes field. This
prevented bandwidth limiting from working. Initialize the field as it
was done before multiqueue support was added.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mark Salyzyn <salyzyn@android.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
----
v2: switch to sock_flag(sk, SOCK_DEAD) and added net/caif/caif_socket.c
v3: return -ECONNRESET in upstream caller of wait function for SOCK_DEAD Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A pair of nested spin locks was introduced in commit 63502b8d0
"dp83640: Fix receive timestamp race condition".
Unfortunately the 'flags' parameter was reused for the inner lock,
clobbering the originally saved IRQ state. This patch fixes the issue
by changing the inner lock to plain spin_lock without irqsave.
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Callers of the ext_write function are supposed to hold a mutex that
protects the state of the dialed page, but one caller was missing the
lock from the very start, and over time the code has been changed
without following the rule. This patch cleans up the call sites in
violation of the rule.
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the calibration function that corrects the initial offsets
among multiple devices only works the first time. If the function is
called more than once, the calibration fails and bogus offsets will be
programmed into the devices.
In a well hidden spot, the device documentation tells that trigger indexes
0 and 1 are special in allowing the TRIG_IF_LATE flag to actually work.
This patch fixes the issue by using one of the special triggers during the
recalibration method.
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When more than a multicast address is present in a MLDv2 report, all but
the first address is ignored, because the code breaks out of the loop if
there has not been an error adding that address.
This has caused failures when two guests connected through the bridge
tried to communicate using IPv6. Neighbor discoveries would not be
transmitted to the other guest when both used a link-local address and a
static address.
This only happens when there is a MLDv2 querier in the network.
The fix will only break out of the loop when there is a failure adding a
multicast address.
The mdb before the patch:
dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp
dev ovirtmgmt port bond0.86 grp ff02::2 temp
After the patch:
dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp
dev ovirtmgmt port bond0.86 grp ff02::fb temp
dev ovirtmgmt port bond0.86 grp ff02::2 temp
dev ovirtmgmt port bond0.86 grp ff02::d temp
dev ovirtmgmt port vnet0 grp ff02::1:ff00:76 temp
dev ovirtmgmt port bond0.86 grp ff02::16 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff00:77 temp
dev ovirtmgmt port bond0.86 grp ff02::1:ff00:def temp
dev ovirtmgmt port bond0.86 grp ff02::1:ffa1:40bf temp
Fixes: 08b202b67264 ("bridge br_multicast: IPv6 MLD support.") Reported-by: Rik Theys <Rik.Theys@esat.kuleuven.be> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com> Tested-by: Rik Theys <Rik.Theys@esat.kuleuven.be> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tx_curr_frame_payload field is u32. When we try to calculate a
small negative delta based on it, we end up with a positive integer
close to 2^32 instead. So the tx_bytes pointer increases by about
2^32 for every transmitted frame.
Fix by calculating the delta as a signed long.
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Reported-by: Florian Bruhin <me@the-compiler.org> Fixes: 7a1e890e2168 ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm") Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ip_error does not check if in_dev is NULL before dereferencing it.
IThe following sequence of calls is possible:
CPU A CPU B
ip_rcv_finish
ip_route_input_noref()
ip_route_input_slow()
inetdev_destroy()
dst_input()
With the result that a network device can be destroyed while processing
an input packet.
A crash was triggered with only unicast packets in flight, and
forwarding enabled on the only network device. The error condition
was created by the removal of the network device.
As such it is likely the that error code was -EHOSTUNREACH, and the
action taken by ip_error (if in_dev had been accessible) would have
been to not increment any counters and to have tried and likely failed
to send an icmp error as the network device is going away.
Therefore handle this weird case by just dropping the packet if
!in_dev. It will result in dropping the packet sooner, and will not
result in an actual change of behavior.
Fixes: 251da4130115b ("ipv4: Cache ip_error() routes even when not forwarding.") Reported-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Tested-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
while true; do
tc qdisc add dev foo root handle 1: prio
tc filter add dev foo parent 1: u32 match u32 0 0 flowid 1
tc qdisc del dev foo root
rmmod cls_u32
done
... will panic the kernel. Moreover, he bisected the change
apparently introducing it to 78fd1d0ab072 ("netlink: Re-add
locking to netlink_lookup() and seq walker").
The removal of synchronize_net() from the netlink socket
triggering the qdisc to be removed, seems to have uncovered
an RCU resp. module reference count race from the tc API.
Given that RCU conversion was done after e341694e3eb5 ("netlink:
Convert netlink_lookup() to use RCU protected hash table")
which added the synchronize_net() originally, occasion of
hitting the bug was less likely (not impossible though):
When qdiscs that i) support attaching classifiers and,
ii) have at least one of them attached, get deleted, they
invoke tcf_destroy_chain(), and thus call into ->destroy()
handler from a classifier module.
After RCU conversion, all classifier that have an internal
prio list, unlink them and initiate freeing via call_rcu()
deferral.
Meanhile, tcf_destroy() releases already reference to the
tp->ops->owner module before the queued RCU callback handler
has been invoked.
Subsequent rmmod on the classifier module is then not prevented
since all module references are already dropped.
By the time, the kernel invokes the RCU callback handler from
the module, that function address is then invalid.
One way to fix it would be to add an rcu_barrier() to
unregister_tcf_proto_ops() to wait for all pending call_rcu()s
to complete.
synchronize_rcu() is not appropriate as under heavy RCU
callback load, registered call_rcu()s could be deferred
longer than a grace period. In case we don't have any pending
call_rcu()s, the barrier is allowed to return immediately.
Since we came here via unregister_tcf_proto_ops(), there
are no users of a given classifier anymore. Further nested
call_rcu()s pointing into the module space are not being
done anywhere.
Only cls_bpf_delete_prog() may schedule a work item, to
unlock pages eventually, but that is not in the range/context
of cls_bpf anymore.
Fixes: 25d8c0d55f24 ("net: rcu-ify tcf_proto") Fixes: 9888faefe132 ("net: sched: cls_basic use RCU") Reported-by: Vijay Subramanian <subramanian.vijay@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: John Fastabend <john.r.fastabend@intel.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Thomas Graf <tgraf@suug.ch> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Alexei Starovoitov <ast@plumgrid.com> Tested-by: Vijay Subramanian <subramanian.vijay@gmail.com> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit <5cf3d46192fc> ("udp: Simplify__udp*_lib_mcast_deliver")
simplified the filter for incoming IPv6 multicast but removed
the check of the local socket address and the UDP destination
address.
This patch restores the filter to prevent sockets bound to a IPv6
multicast IP to receive other UDP traffic link unicast.
Signed-off-by: Henning Rogge <hrogge@gmail.com> Fixes: 5cf3d46192fc ("udp: Simplify__udp*_lib_mcast_deliver") Cc: "David S. Miller" <davem@davemloft.net> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d13a96c74fc ("ipv6: tcp: fix flowlabel value in ACK messages
send from TIME_WAIT") added the flow label in the last TCP packets.
Unfortunately, it was not casted properly.
This patch replace the buggy shift with be32_to_cpu/cpu_to_be32.
Fixes: 1d13a96c74fc ("ipv6: tcp: fix flowlabel value in ACK messages") Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before the patch, the command 'ip link add bond2 type bond mode 802.3ad'
causes the kernel to send a rtnl message for the bond2 interface, with an
ifindex 0.
'ip monitor' shows:
0: bond2: <BROADCAST,MULTICAST,MASTER> mtu 1500 state DOWN group default
link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
9: bond2@NONE: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN group default
link/ether ea:3e:1f:53:92:7b brd ff:ff:ff:ff:ff:ff
[snip]
The patch fixes the spotted bug by checking in bond driver if the interface
is registered before calling the notifier chain.
It also adds a check in rtmsg_ifinfo() to prevent this kind of bug in the
future.
Fixes: d4261e565000 ("bonding: create netlink event when bonding option is changed") CC: Jiri Pirko <jiri@resnulli.us> Reported-by: Julien Meunier <julien.meunier@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit c5adde9468b0714a051eac7f9666f23eb10b61f7 ("netlink:
eliminate nl_sk_hash_lock") breaks the autobind retry mechanism
because it doesn't reset portid after a failed netlink_insert.
This means that should autobind fail the first time around, then
the socket will be stuck in limbo as it can never be bound again
since it already has a non-zero portid.
Fixes: c5adde9468b0 ("netlink: eliminate nl_sk_hash_lock") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RGMII interfaces come in multiple flavors: RGMII with transmit or
receive internal delay, no delays at all, or delays in both direction.
This change extends the initial check for PHY_INTERFACE_MODE_RGMII to
cover all of these variants since EEE should be allowed for any of these
modes, since it is a property of the RGMII, hence Gigabit PHY capability
more than the RGMII electrical interface and its delays.
Fixes: a59a4d192166 ("phy: add the EEE support and the way to access to the MMD registers") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
x86 has variable length encoding. x86 JIT compiler is trying
to pick the shortest encoding for given bpf instruction.
While doing so the jump targets are changing, so JIT is doing
multiple passes over the program. Typical program needs 3 passes.
Some very short programs converge with 2 passes. Large programs
may need 4 or 5. But specially crafted bpf programs may hit the
pass limit and if the program converges on the last iteration
the JIT compiler will be producing an image full of 'int 3' insns.
Fix this corner case by doing final iteration over bpf program.
Fixes: 0a14842f5a3c ("net: filter: Just In Time compiler for x86-64") Reported-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Tested-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FROM_BE16:
'ror %reg, 8' doesn't clear upper bits of the register,
so use additional 'movzwl' insn to zero extend 16 bits into 64
FROM_LE16:
should zero extend lower 16 bits into 64 bit
FROM_LE32:
should zero extend lower 32 bits into 64 bit
Fixes: 89aa075832b0 ("net: sock: allow eBPF programs to be attached to sockets") Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code in __netdev_upper_dev_link() has an over-stringent
loop detection logic that actually prevents valid configurations
from working correctly.
In particular, the logic returns an error if an upper device
is already in the list of all upper devices for a given dev.
This particular check seems to be a overzealous as it disallows
perfectly valid configurations. For example:
# ip l a link eth0 name eth0.10 type vlan id 10
# ip l a dev br0 typ bridge
# ip l s eth0.10 master br0
# ip l s eth0 master br0 <--- Will fail
If you switch the last two commands (add eth0 first), then both
will succeed. If after that, you remove eth0 and try to re-add
it, it will fail!
It appears to be enough to simply check adj_list to keeps things
safe.
I've tried stacking multiple devices multiple times in all different
combinations, and either rx_handler registration prevented the stacking
of the device linking cought the error.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Veaceslav Falico <vfalico@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
exit_aio() currently serializes killing io contexts. Each context
killing ends up having to do percpu_ref_kill(), which in turns has
to wait for an RCU grace period. This can take a long time, depending
on the number of contexts. And there's no point in doing them serially,
when we could be waiting for all of them in one fell swoop.
This patches makes my fio thread offload test case exit 0.2s instead
of almost 6s.
Crush temporary buffers are allocated as per replica size configured
by the user. When there are more final osds (to be selected as per
rule) than the replicas, buffer overlaps and it causes crash. Now, it
ensures that at most num-rep osds are selected even if more number of
osds are allowed by the rule.
Fixes: a87938b2e246b81b4fb ("fs/binfmt_elf.c: fix bug in loading of PIE binaries") Reported-by: James Hogan <james.hogan@imgtec.com> Cc: Michael Davidson <md@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent change removed the need for locking around writing
to "sync_action" (and various other places), but introduced a
subtle race.
When e.g. setting 'reshape' on a 'frozen' array, the 'frozen'
flag is cleared before 'reshape' is set, so the md thread can
get in and start trying recovery - which isn't wanted.
So instead of clearing MD_RECOVERY_FROZEN for any command
except 'frozen', only clear it when each specific command
is parsed. This allows the handling of 'reshape' to clear
the bit while a lock is held.
Also remove some places where we set MD_RECOVERY_NEEDED,
as it is always set on non-error exit of the function.
Signed-off-by: NeilBrown <neilb@suse.de> Fixes: 6791875e2e53 ("md: make reconfig_mutex optional for writes to md sysfs files.") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PWM hardware on Pistachio platform has a maximum timebase steps
value to 255. To fix it, let's introduce a compatible-specific
data structure to contain the SoC-specific details and use it to
specify a maximum timebase.
Also, let's limit the minimum timebase to 16 steps, to allow a sane
range of duty cycle steps.
Block drivers are responsible for calling flush_dcache_page() on each
BIO request. This operation keeps the I$ coherent with the D$ on
architectures that don't have hardware coherency support. Without this
flush, random crashes are seen when executing user programs from an ext4
filesystem backed by a ubiblock device.
This patch is based on the change implemented in commit 2d4dc890b5c8
("block: add helpers to run flush_dcache_page() against a bio and a
request's pages").
Fixes: 9d54c8a33eec ("UBI: R/O block driver on top of UBI volumes") Signed-off-by: Kevin Cernekee <cernekee@chromium.org> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function devm_ioremap() returns NULL
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
We used to read file_handle twice. Once to get the amount of extra
bytes, and once to fetch the entire structure.
This may be problematic since we do size verifications only after the
first read, so if the number of extra bytes changes in userspace between
the first and second calls, we'll have an incoherent view of
file_handle.
Instead, read the constant size once, and copy that over to the final
structure without having to re-read it again.
This patch sets the local memory size that is reported to userspace to 0.
This is done to make sure that userspace won't try to allocate local memory
for HSA.
As long as amdkfd doesn't support allocating local memory for HSA,
we need this patch.
With following kernel message:
device-mapper: ioctl: can't change device type after initial table load.
DM tries to inherit the current table type using dm_table_set_type()
but it doesn't work as expected because of unnecessary check about
whether the target type is hybrid or not.
Hybrid type is for targets that work as either request-based or bio-based
and not required for blk-mq or non blk-mq checking.
Fixes: 65803c205983 ("dm table: train hybrid target type detection to select blk-mq if appropriate") Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dm_merge_bvec() was originally added in f6fccb ("dm: introduce
merge_bvec_fn"). In that commit a value in sectors is converted to
bytes using << 9, and then assigned to an int. This code made
assumptions about the value of BIO_MAX_SECTORS.
A later commit 148e51 ("dm: improve documentation and code clarity in
dm_merge_bvec") was meant to have no functional change but it removed
the use of BIO_MAX_SECTORS in favor of using queue_max_sectors(). At
this point the cast from sector_t to int resulted in a zero value. The
fallout being dm_merge_bvec() would only allow a single page to be added
to a bio.
This interim fix is minimal for the benefit of stable@ because the more
comprehensive cleanup of passing a sector_t to all DM targets' merge
function will impact quite a few DM targets.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have that bug for years and some users report side effects when fixing it on older hardware.
So revert it for VM_CONTEXT0_PAGE_TABLE_END_ADDR, but keep it for VM 1-15.
Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm/atomic-helpers: Recover full cursor plane behaviour
we've added a hack to atomic helpers to never to vblank waits for
cursor updates through the legacy apis since that's what X expects.
Unfortunately we've (again) forgotten to adjust the transitional
helpers. Do this now.
This fixes regressions for drivers only partially converted over to
atomic (like i915).
Reported-by: Pekka Paalanen <ppaalanen@gmail.com> Cc: Pekka Paalanen <ppaalanen@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-and-tested-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mapping range is inclusive between starting and ending addresses.
Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case of a DMA mapping error on the last iteration of
the loop of the allocation of memory of the FW monitor we
indeed free the pages, but don't NULL out the page variable
thus allowing for the possibility of setting the FW monitor
variables with invalid data to use.
fw_status is the only pointer pointing to a block of memory
allocated above and should be freed after use.
Note: this come from Klockwork static analyzer.
projects / thirdparty / kernel / stable.git / log
