In summary, the new patch added taking the io_buf_list_put_lock while under
an irq-disabled hbalock. This created a lock heirarchy dependent upon irq
being disabled, and there are paths that take the io_buf_list_put_lock
without disabling irq.
Looking at the lpfc_io_free routine, which is where the new heirarchy was
introduced, there is no reason to be taking out the hbalock and raising
irq, as the functionality is replaced by the io_buf_list_xxx locks.
Resolve by removing the hbalock/irq calls in lpfc_io_free.
Fixes: 5e5b511d8bfa ("scsi: lpfc: Partition XRI buffer list across Hardware Queues") Reported-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A prior patch which added support for non-uniform allocation of MSIX
vectors now causes a smatch complaint:
drivers/scsi/lpfc/lpfc_scsi.c:3674 lpfc_scsi_cmd_iocb_cmpl()
error: we previously assumed 'phba->sli4_hba.hdwq' could be
null (see line 3667)
Resolve by removing the unnecessary check for a NULL hdwq table.
Fixes 6a828b0f6192: ("scsi: lpfc: Support non-uniform allocation of MSIX vectors to hardware queues") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The adapter initialization sequence enables interrupts, initializes the
adapter link_state to LINK_DOWN, then issues commands to initialize the
adapter. The interrupt handler on the adapter validates the link_state (has
to be at least LINK_DOWN) and if invalid, will discard the interrupting
event.
In most cases, there is not a command completion, thus an interrupt until
the initialization commands have been sent which is post the setting of
state to LINK_DOWN. However, in cases of firmware reset, the reset will
modify the link_state to an invalid value (indicating a reset of the
adapter) and there occasionally are cases where the adapter will generate
an asynchronous event which shares the eq/cq used for mailbox commands. In
the failure case, an interrupt is generated immediately after enabling them
due to the async event. As link_state is invalid, the eq is list and the
CQ not serviced. At this point link_state is initialized and the mailbox
command sent. As the CQ has not been serviced, it is not armed, so no
interrupt event is generated when the mailbox command completes.
Modify the initialization sequence so that interrupts are enabled after
link_state is properly initialized, which avoids the race condition with
the async event.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
During debug, it was seen that the driver is issuing commands specific to
SLI3 on SLI4 devices. Although the adapter correctly rejected the command,
this should not be done.
Revise the code to stop sending these commands on a SLI4 adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Two saa7146/hexium files contain a construct that causes a warning
when built with clang:
drivers/media/pci/saa7146/hexium_orion.c:210:12: error: stack frame size of 2272 bytes in function 'hexium_probe'
[-Werror,-Wframe-larger-than=]
static int hexium_probe(struct saa7146_dev *dev)
^
drivers/media/pci/saa7146/hexium_gemini.c:257:12: error: stack frame size of 2304 bytes in function 'hexium_attach'
[-Werror,-Wframe-larger-than=]
static int hexium_attach(struct saa7146_dev *dev, struct saa7146_pci_extension_data *info)
^
This one happens regardless of KASAN, and the problem is that a
constructor to initialize a dynamically allocated structure leads
to a copy of that structure on the stack, whereas gcc initializes
it in place.
If the driver undergoes repeated host resets it starts losing exchange
structures and eventually returns SCSI_MLQUEUE_HOST_BUSY and does not
recover. The offline path is not reclaiming the outstanding ios on the fcp
pring txcmplq before calling lpfc_destroy_multixripool, which causes the
txmcplq to be reinit and the resources lost.
Flush the fcp rings before destroying the multixripools.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver is reporting support for NVME even when not configured for NVME
operation.
Fix (and make more readable) when NVME protocol support is indicated.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The FDMI manufacturer value being reported on Linux is inconsistent with
other OS's.
Set the value to "Emulex Corporation" for consistency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not possible to use devm_kzalloc since that memory is
freed immediately when the device instance is unbound.
Various objects like the video device may still be in use
since someone has the device node open, and when that is closed
it expects the memory to be around.
So use kzalloc and release it at the appropriate time.
The media_device is part of a static global vimc_device struct.
The media framework expects this to be zeroed before it is
used, however, since this is a global this is not the case if
vimc is unbound and then bound again.
So call memset to ensure any left-over values are cleared.
Commit 0650a91499e0 ("media: mtk-vcodec: Correct return type for mem2mem
buffer helpers") fixed the return types for mem2mem buffer helper
functions, but omitted two occurrences that are accessed in the
mtk_v4l2_debug() macro. These only trigger compiler errors when DEBUG is
defined.
Fixes: 0650a91499e0 ("media: mtk-vcodec: Correct return type for mem2mem buffer helpers") Signed-off-by: Alexandre Courbot <acourbot@chromium.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang-9 makes some different inlining decisions compared to gcc, which
leads to a warning about a possible stack overflow problem when building
with CONFIG_KASAN, including when setting asan-stack=0, which avoids
most other frame overflow warnings:
drivers/media/platform/vicodec/codec-fwht.c:673:12: error: stack frame size of 2224 bytes in function 'encode_plane'
Manually adding noinline_for_stack annotations in those functions
called by encode_plane() or decode_plane() that require a significant
amount of kernel stack makes this impossible to happen with any
compiler.
When streaming is stopped all URBs are killed, but in fill_frame and in
bulk_irq this results in an attempt to resubmit the killed URB. That is
not what you want and causes spurious kernel messages.
So check if streaming has stopped before resubmitting.
Also check against gspca_dev->streaming rather than vb2_start_streaming_called()
since vb2_start_streaming_called() will return true when in stop_streaming,
but gspca_dev->streaming is set to false when stop_streaming is called.
Fixes: 6992effe5344 ("gspca: Kill all URBs before releasing any of them") Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The state TASK_UNINTERRUPTIBLE should be set just before
schedule_timeout() call, so it knows the sleep mode it should enter.
There is no point in setting TASK_UNINTERRUPTIBLE at the initialization
of the thread as schedule_timeout() will set the state back to
TASK_RUNNING.
This fixes a warning in __might_sleep() call, as it's expecting the
task to be in TASK_RUNNING state just before changing the state to
a sleeping state.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Helen Koike <helen.koike@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
The kms_plane@plane-position-covered-pipe-*-planes subtests can produce
a sequence of atomic commits such that neither active_changed nor
mode_changed but connectors_changed.
When this happens we remove the old stream from the context and add
a new stream but the new stream doesn't have mode_changed=true set.
This incorrect programming sequence causes CRC mismatches to occur in
the test.
The stream->mode_changed value should be set whenever a new stream
is created.
[How]
A new stream is created whenever drm_atomic_crtc_needs_modeset is true.
We previously covered the active_changed and mode_changed conditions
for the CRTC but connectors_changed is also checked within
drm_atomic_crtc_needs_modeset.
So just use drm_atomic_crtc_needs_modeset directly to determine the
mode_changed flag.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
used to be unable to run 4:2:0 if using a dongle because 4k60 bandwidth
exceeded dongle caps
[How]
half pixel clock during comparison to dongle cap. *Could get stuck on black
screen on monitor that don't support 420 but will be selecting 420 as
preferred mode*
Signed-off-by: Martin Leung <martin.leung@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Acked-by: Aidan Wood <Aidan.Wood@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
The dc_gamma_type CUSTOM_GAMMA is used to represent degamma
mappings passed in by drm. This type of gamma must be interpolated
into a transfer function by apply_1d_lut. The line in
mod_color_calculate_degamma_params that handled this case
was erroneously removed.
[How]
For CUSTOM_GAMMA degamma, calculate the lut as before.
Signed-off-by: David Francis <David.Francis@amd.com> Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver should really call dm365_isif_setup_pinmux() through a callback,
but uses a hack to include a davinci specific machine header file when
compile testing instead. This works almost everywhere, but not on the
ARM omap1 platform, which has another header named mach/mux.h. This
causes a build failure:
drivers/staging/media/davinci_vpfe/dm365_isif.c:2028:2: error: implicit declaration of function 'davinci_cfg_reg' [-Werror,-Wimplicit-function-declaration]
davinci_cfg_reg(DM365_VIN_CAM_WEN);
^
drivers/staging/media/davinci_vpfe/dm365_isif.c:2028:2: error: this function declaration is not a prototype [-Werror,-Wstrict-prototypes]
drivers/staging/media/davinci_vpfe/dm365_isif.c:2028:18: error: use of undeclared identifier 'DM365_VIN_CAM_WEN'
davinci_cfg_reg(DM365_VIN_CAM_WEN);
^
drivers/staging/media/davinci_vpfe/dm365_isif.c:2029:18: error: use of undeclared identifier 'DM365_VIN_CAM_VD'
davinci_cfg_reg(DM365_VIN_CAM_VD);
^
drivers/staging/media/davinci_vpfe/dm365_isif.c:2030:18: error: use of undeclared identifier 'DM365_VIN_CAM_HD'
davinci_cfg_reg(DM365_VIN_CAM_HD);
^
drivers/staging/media/davinci_vpfe/dm365_isif.c:2031:18: error: use of undeclared identifier 'DM365_VIN_YIN4_7_EN'
davinci_cfg_reg(DM365_VIN_YIN4_7_EN);
^
drivers/staging/media/davinci_vpfe/dm365_isif.c:2032:18: error: use of undeclared identifier 'DM365_VIN_YIN0_3_EN'
davinci_cfg_reg(DM365_VIN_YIN0_3_EN);
^
7 errors generated.
Exclude omap1 from compile-testing, under the assumption that all others
still work.
Fixes: 4907c73deefe ("media: staging: davinci_vpfe: allow building with COMPILE_TEST") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
Stream update will adjust both info packets and stream params,
need to make sure all things are applied togather.
[how]
add pipe lock during stream update
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 14f4eaeddabc ("media: dvbsky: fix driver unregister logic") fixed
a use-after-free by removing the reference to the frontend after deleting
the backing i2c device.
This has the unfortunate side effect the frontend device is never freed
in the dvb core leaving a dangling device, leading to errors when the
dvb core tries to register the frontend after e.g. a replug as reported
here: https://www.spinics.net/lists/linux-media/msg138181.html
The use after free happened as dvb_usbv2_disconnect calls in this order:
- dvb_usb_device::props->exit(...)
- dvb_usbv2_adapter_frontend_exit(...)
+ if (fe) dvb_unregister_frontend(fe)
+ dvb_usb_device::props->frontend_detach(...)
Moving the release of the i2c device from exit() to frontend_detach()
avoids the dangling pointer access and allows the core to unregister
the frontend.
This was originally reported for a DVBSky T680CI, but it also affects
the MyGica T230C. As all supported devices structure the registration/
unregistration identically, apply the change for all device types.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
si2165_readreg8() may fail. Looking into si2165_readreg8(), we will find
that "val_tmp" will be an uninitialized value when regmap_read() fails.
"val_tmp" is then assigned to "val". So if si2165_readreg8() fails,
"val" will be a random value. Further use will lead to undefined
behaviors. The fix checks if si2165_readreg8() fails, and if so, returns
its error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Reviewed-by: Matthias Schwarzott <zzam@gentoo.org> Tested-by: Matthias Schwarzott <zzam@gentoo.org> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are some new e1000e devices can only be woken up from D3 one time,
by plugging Ethernet cable. Subsequent cable plugging does set PME bit
correctly, but it still doesn't get woken up.
Since e1000e connects to the root complex directly, we rely on ACPI to
wake it up. In this case, the GPE from _PRW only works once and stops
working after that. Though it appears to be a platform bug, e1000e
maintainers confirmed that I219 does not support D3.
So disable runtime PM on CNP+ chips. We may need to disable earlier
generations if this bug also hit older platforms.
Bugzilla: https://bugzilla.kernel.org/attachment.cgi?id=280819 Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes issues with VF queues being disabled, and VF netdev
network carrier being lost after reset. Basically, we need to check if VF
is enabled, and queue configured in reset_all_vfs flow, and disable/enable
those queues appropriately whenever the function is called after
Global/CORER/PFR reset/rebuild/replay.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When start_streaming was called both last_src_buf and last_dst_buf
pointers were set to NULL, but this depends on whether the capture
or output queue starts streaming.
When decoding with resolution changes in between the capture queue
has to restart streaming whenever a resolution change occurs. And
that would reset last_src_buf as well, which causes a problem if
the decoder was stopped by the application. Since last_src_buf
is now NULL, the LAST flag is never set for the last capture
buffer.
The imgu_rpm_dummy_cb() looks like an API misuse that is explained
in the comment above it. Aside from that, it also causes a warning
when power management support is disabled:
drivers/staging/media/ipu3/ipu3.c:794:12: error: 'imgu_rpm_dummy_cb' defined but not used [-Werror=unused-function]
The warning is at least easy to fix by marking the function as
__maybe_unused.
[Why]
The plane_reset callback is subclassed but hasn't been updated since
the drm helper got updated to include resetting alpha related state
(state->alpha and state->pixel_blend_mode). The overlay planes
exposed by amdgpu_dm were therefore being rendered as invisible by
default ever since supported was exposed for alpha blending properties
on overlays.
This caused regressions in igt@kms_plane_multiple@atomic-tiling-none
and igt@kms_plane@plane-position-covered-pipe tests.
[How]
Reset the plane state values to their correct values as defined in
the drm helper.
This fixes the IGT test regression.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Somewhere in the atomic check reshuffle ABM got lost.
ABM is a crtc property (copied from a connector property).
It can change without a modeset, just like underscan.
[How]
In the skip_modeset branch of atomic check crtc updates,
copy over the abm property.
Signed-off-by: David Francis <David.Francis@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
In certain cases we do link training when we don't have a backend.
[How]
In dc_link_set_preferred_link_settings(), store preferred link settings
first and then verify that the link is DP and the link stream's backend is
enabled. If either is false, then we will not do any link retraining.
Signed-off-by: Samson Tam <Samson.Tam@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Releasing planes should not release the 2nd odm pipe right away,
this change leaves us with 2 pipes with null planes and same stream
when planes are released during odm.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The regulator header has empty inline functions for most interfaces,
but not regulator_get_linear_step(), which has just grown a user
that does not depend on regulators otherwise:
drivers/clk/tegra/clk-tegra124-dfll-fcpu.c: In function 'get_alignment_from_regulator':
drivers/clk/tegra/clk-tegra124-dfll-fcpu.c:555:19: error: implicit declaration of function 'regulator_get_linear_step'; did you mean 'regulator_get_drvdata'? [-Werror=implicit-function-declaration]
align->step_uv = regulator_get_linear_step(reg);
^~~~~~~~~~~~~~~~~~~~~~~~~
regulator_get_drvdata
cc1: all warnings being treated as errors
scripts/Makefile.build:278: recipe for target 'drivers/clk/tegra/clk-tegra124-dfll-fcpu.o' failed
Add the missing stub along the others.
Fixes: b3cf8d069505 ("clk: tegra: dfll: CVB calculation alignment with the regulator") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Memory allocated via kmemdup might fail and return a NULL pointer.
This patch adds a check on the return value of kmemdup and passes the
error upstream.
In enumerate_services, ida_simple_get on failure can return an error and
leaks memory. The patch ensures that the dev_set_name is set on non
failure cases, and releases memory during failure.
The buffer descriptor setup loop is correct only if it is setting up at
least one bd struct. Besides, there is an error if dma_map_sg() returns
0, which is possible and must be handled.
Additionally, remove the BUG_ON() checking sglen, which is unnecessary
because we configure DMA with that constraint during init.
Amazingly a mlx5e_tc function is being called from the eswitch layer,
which is by itself very terrible! The function was declared locally in
eswitch_offloads.c so it could be used there, which caused the following
compilation warning, fix that.
drivers/.../mlx5/core/en_tc.c:3242:6: [-Werror=missing-prototypes]
error: no previous prototype for ‘mlx5e_tc_clean_fdb_peer_flows’
Fixes: 04de7dda7394 ("net/mlx5e: Infrastructure for duplicated offloading of TC flows") Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
calculates the physical processor ID from the initial_apicid by shifting
*bits*.
However, this does not work for 1-Die and 2-Die 2-socket systems.
According to document [1] section 2.1.11.1, the bits is the value of
CPUID_Fn80000008_ECX[12:15]. The possible values are 4, 5 or 6 which
mean:
4 - 1 die
5 - 2 dies
6 - 3/4 dies.
Hygon programs the initial ApicId the same way as AMD. The ApicId is
read from CPUID_Fn00000001_EBX (see section 2.1.11.1 of referrence [1])
and the definition is as below (see section 2.1.10.2.1.3 of [1]):
-------------------------------------------------
Bit | 6 | 5 4 | 3 | 2 1 0 |
|-----------|---------|--------|----------------|
IDs | Socket ID | Node ID | CCX ID | Core/Thread ID |
-------------------------------------------------
So for 3/4-Die configurations, the bits variable is 6, which is the same
as the ApicID definition field.
For 1-Die and 2-Die configurations, bits is 4 or 5, which will cause the
right shifted result to not be exactly the value of socket ID.
However, the socket ID should be obtained from ApicId[6]. To fix the
problem and match the ApicID field definition, set the shift bits to 6
for all Hygon family 18h multi-die CPUs.
Because AMD doesn't have 2-Socket systems with 1-Die/2-Die processors
(see reference [2]), this doesn't need to be changed on the AMD side but
only for Hygon.
adma driver is using pm_clk_*() interface for managing clock resources.
With this it is observed that clocks remain ON always. This happens on
Tegra devices which use BPMP co-processor to manage clock resources,
where clocks are enabled during prepare phase. This is necessary because
clocks to BPMP are always blocking. When pm_clk_*() interface is used on
such Tegra devices, clock prepare count is not balanced till remove call
happens for the driver and hence clocks are seen ON always. Thus this
patch replaces pm_clk_*() with devm_clk_*() framework.
Currently incoming ARP Replies, for example via a DHT-PUT message, do
not update the timeout for an already existing DAT entry. These ARP
Replies are dropped instead.
This however defeats the purpose of the DHCPACK snooping, for instance.
Right now, a DAT entry in the DHT will be purged every five minutes,
likely leading to a mesh-wide ARP Request broadcast after this timeout.
Which then recreates the entry. The idea of the DHCPACK snooping is to
be able to update an entry before a timeout happens, to avoid ARP Request
flooding.
This patch fixes this issue by updating a DAT entry on incoming
ARP Replies even if a matching DAT entry already exists. While still
filtering the ARP Reply towards the soft-interface, to avoid duplicate
messages on the client device side.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Acked-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang correctly points out a code path that would lead
to an uninitialized variable use:
security/selinux/netlabel.c:310:6: error: variable 'addr' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
if (ip_hdr(skb)->version == 4) {
^~~~~~~~~~~~~~~~~~~~~~~~~
security/selinux/netlabel.c:322:40: note: uninitialized use occurs here
rc = netlbl_conn_setattr(ep->base.sk, addr, &secattr);
^~~~
security/selinux/netlabel.c:310:2: note: remove the 'if' if its condition is always true
if (ip_hdr(skb)->version == 4) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
security/selinux/netlabel.c:291:23: note: initialize the variable 'addr' to silence this warning
struct sockaddr *addr;
^
= NULL
This is probably harmless since we should not see ipv6 packets
of CONFIG_IPV6 is disabled, but it's better to rearrange the code
so this cannot happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[PM: removed old patchwork link, fixed checkpatch.pl style errors] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the current implementation of ice_reset_subtask, if multiple reset
types are set in the pf->state, the most intrusive one is meant to be
performed only, but the bits requesting the other types are not being
cleared. This would lead to another reset being performed the next time
the service task is scheduled.
Change the flow of ice_reset_subtask so that all reset request bits in
pf->state are cleared, and we still perform the most intrusive of the
resets requested.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function 'v4l2_m2m_buf_copy_metadata' should
be called even if decoding/encoding ends with
status VB2_BUF_STATE_ERROR, so that the metadata
is copied from the source buffer to the dest buffer.
clang -Wuninitialized incorrectly sees a variable being used without
initialization:
drivers/scsi/lpfc/lpfc_nvme.c:2102:37: error: variable 'localport' is uninitialized when used here
[-Werror,-Wuninitialized]
lport = (struct lpfc_nvme_lport *)localport->private;
^~~~~~~~~
drivers/scsi/lpfc/lpfc_nvme.c:2059:38: note: initialize the variable 'localport' to silence this warning
struct nvme_fc_local_port *localport;
^
= NULL
1 error generated.
This is clearly in dead code, as the condition leading up to it is always
false when CONFIG_NVME_FC is disabled, and the variable is always
initialized when nvme_fc_register_localport() got called successfully.
Change the preprocessor conditional to the equivalent C construct, which
makes the code more readable and gets rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang -Wuninitialized notices that on is_qla40XX we never allocate any DMA
memory in get_fw_boot_info() but attempt to free it anyway:
drivers/scsi/qla4xxx/ql4_os.c:5915:7: error: variable 'buf_dma' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
if (!(val & 0x07)) {
^~~~~~~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5985:47: note: uninitialized use occurs here
dma_free_coherent(&ha->pdev->dev, size, buf, buf_dma);
^~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5915:3: note: remove the 'if' if its condition is always true
if (!(val & 0x07)) {
^~~~~~~~~~~~~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5885:20: note: initialize the variable 'buf_dma' to silence this warning
dma_addr_t buf_dma;
^
= 0
Skip the call to dma_free_coherent() here.
Fixes: 2a991c215978 ("[SCSI] qla4xxx: Boot from SAN support for open-iscsi") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 63f545ed1285 ("ice: Add support for adaptive interrupt moderation")
was meant to add support for adaptive interrupt moderation but there was
an error on my part while formatting the patch, and thus only part of the
patch ended up being submitted.
This patch rectifies the error by adding the rest of the code.
Fixes: 63f545ed1285 ("ice: Add support for adaptive interrupt moderation") Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If ohci-platform is runtime suspended, we can currently get an "imprecise
external abort" on reboot with ohci-platform loaded when PM runtime
is implemented for the SoC.
Let's fix this by adding PM runtime support to usb_hcd_platform_shutdown.
Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rcu_head_after_call_rcu() function reads the rhp->func pointer twice,
which can result in a false-positive WARN_ON_ONCE() if the callback
were passed to call_rcu() between the two reads. Although racing
rcu_head_after_call_rcu() with call_rcu() is to be a dubious use case
(the return value is not reliable in that case), intermittent and
irreproducible warnings are also quite dubious. This commit therefore
uses a single READ_ONCE() to pick up the value of rhp->func once, then
tests that value twice, thus guaranteeing consistent processing within
rcu_head_after_call_rcu()().
Neverthless, racing rcu_head_after_call_rcu() with call_rcu() is still
a dubious use case.
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
[ paulmck: Add blank line after declaration per checkpatch.pl. ] Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the specified rcuperf.perf_type is not in the rcu_perf_init()
function's perf_ops[] array, rcuperf prints some console messages and
then invokes rcu_perf_cleanup() to set state so that a future torture
test can run. However, rcu_perf_cleanup() also attempts to end the
test that didn't actually start, and in doing so relies on the value
of cur_ops, a value that is not particularly relevant in this case.
This can result in confusing output or even follow-on failures due to
attempts to use facilities that have not been properly initialized.
This commit therefore sets the value of cur_ops to NULL in this case and
inserts a check near the beginning of rcu_perf_cleanup(), thus avoiding
relying on an irrelevant cur_ops value.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Linux reads MCG_CAP[Count] to find the number of MCA banks visible to a
CPU. Currently, this number is the same for all CPUs and a warning is
shown if there is a difference. The number of banks is overwritten with
the MCG_CAP[Count] value of each following CPU that boots.
According to the Intel SDM and AMD APM, the MCG_CAP[Count] value gives
the number of banks that are available to a "processor implementation".
The AMD BKDGs/PPRs further clarify that this value is per core. This
value has historically been the same for every core in the system, but
that is not an architectural requirement.
Future AMD systems may have different MCG_CAP[Count] values per core,
so the assumption that all CPUs will have the same MCG_CAP[Count] value
will no longer be valid.
Also, the first CPU to boot will allocate the struct mce_banks[] array
using the number of banks based on its MCG_CAP[Count] value. The machine
check handler and other functions use the global number of banks to
iterate and index into the mce_banks[] array. So it's possible to use an
out-of-bounds index on an asymmetric system where a following CPU sees a
MCG_CAP[Count] value greater than its predecessors.
Thus, allocate the mce_banks[] array to the maximum number of banks.
This will avoid the potential out-of-bounds index since the value of
mca_cfg.banks is capped to MAX_NR_BANKS.
Set the value of mca_cfg.banks equal to the max of the previous value
and the value for the current CPU. This way mca_cfg.banks will always
represent the max number of banks detected on any CPU in the system.
This will ensure that all CPUs will access all the banks that are
visible to them. A CPU that can access fewer than the max number of
banks will find the registers of the extra banks to be read-as-zero.
Furthermore, print the resulting number of MCA banks in use. Do this in
mcheck_late_init() so that the final value is printed after all CPUs
have been initialized.
Finally, get bank count from target CPU when doing injection with mce-inject
module.
[ bp: Remove out-of-bounds example, passify and cleanup commit message. ]
If the specified rcutorture.torture_type is not in the rcu_torture_init()
function's torture_ops[] array, rcutorture prints some console messages
and then invokes rcu_torture_cleanup() to set state so that a future
torture test can run. However, rcu_torture_cleanup() also attempts to
end the test that didn't actually start, and in doing so relies on the
value of cur_ops, a value that is not particularly relevant in this case.
This can result in confusing output or even follow-on failures due to
attempts to use facilities that have not been properly initialized.
This commit therefore sets the value of cur_ops to NULL in this case
and inserts a check near the beginning of rcu_torture_cleanup(),
thus avoiding relying on an irrelevant cur_ops value.
Reported-by: kernel test robot <rong.a.chen@intel.com> Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There has been a lurking "TBD" in the machine check poll routine ever
since it was first split out from the machine check handler. The
potential issue is that the poll routine may have just begun a read from
the STATUS register in a machine check bank when the hardware logs an
error in that bank and signals a machine check.
That race used to be pretty small back when machine checks were
broadcast, but the addition of local machine check means that the poll
code could continue running and clear the error from the bank before the
local machine check handler on another CPU gets around to reading it.
Fix the code to be sure to only process errors that need to be processed
in the poll code, leaving other logged errors alone for the machine
check handler to find and process.
[ bp: Massage a bit and flip the "== 0" check to the usual !(..) test. ]
Fixes: b79109c3bbcf ("x86, mce: separate correct machine check poller and fatal exception handler") Fixes: ed7290d0ee8f ("x86, mce: implement new status bits") Reported-by: Ashok Raj <ashok.raj@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Ashok Raj <ashok.raj@intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: linux-edac <linux-edac@vger.kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Cc: Yazen Ghannam <Yazen.Ghannam@amd.com> Link: https://lkml.kernel.org/r/20190312170938.GA23035@agluck-desk Signed-off-by: Sasha Levin <sashal@kernel.org>
The module was initializing completions whenever it was going to wait on
them, and not when the completion was allocated. This is incorrect
according to the completion docs:
Calling init_completion() on the same completion object twice is
most likely a bug [...]
Re-initialization is also unnecessary because the module never uses
complete_all(). Fix this by only ever initializing the completion a
single time, and log if the completions are not consumed as intended
(this is not a fatal problem, but should not go unnoticed).
ipw->attr_memory and ipw->common_memory are assigned with the
return value of ioremap. ioremap may fail, but no checks
are enforced. The fix inserts the checks to avoid potential
NULL pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For regular serial ports we do not initialize value of vtermno
variable. A garbage value is assigned for non console ports.
The value can be observed as a random integer with [1].
[1] vim /sys/kernel/debug/virtio-ports/vport*p*
This patch initialize the value of vtermno for console serial
ports to '1' and regular serial ports are initiaized to '0'.
This patch fixes the error exit path of fastrpc_init_create_process().
If the DMA allocation or the DSP invoke fails the fastrpc_map was freed
but not removed from the mapping list leading to a double free once the
mapping list is emptied in fastrpc_device_release().
[srinivas kandagatla]: Cleaned up error path labels and reset init mem
to NULL after free Fixes: d73f71c7c6ee("misc: fastrpc: Add support for create remote init process") Signed-off-by: Thierry Escande <thierry.escande@linaro.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
dma_alloc_coherent buffers could have writes queued in store buffers so
commit them before sending buffer to DSP using correct dma barriers.
Same with vice-versa.
Fixes the following crash as the return was missing from the check if an
fcport is offloaded. If we hit this code we continue to try to post an
invalid task which can lead to the crash:
The InfiniBand Architecture Specification section 10.6.7.2.4 TYPE 2 MEMORY
WINDOWS says that if the CI supports the Base Memory Management Extensions
defined in this specification, the R_Key format for a Type 2 Memory Window
must consist of:
* 24 bit index in the most significant bits of the R_Key, which is owned
by the CI, and
* 8 bit key in the least significant bits of the R_Key, which is owned by
the Consumer.
This means that the kernel should compare only the index part of a R_Key
to determine equality with another R_Key.
Fixes: db570d7deafb ("IB/mlx5: Add ODP support to MW") Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com> Signed-off-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Several people reported testing failures after setting CLOCK_REALTIME close
to the limits of the kernel internal representation in nanoseconds,
i.e. year 2262.
The failures are exposed in subsequent operations, i.e. when arming timers
or when the advancing CLOCK_MONOTONIC makes the calculation of
CLOCK_REALTIME overflow into negative space.
Now people start to paper over the underlying problem by clamping
calculations to the valid range, but that's just wrong because such
workarounds will prevent detection of real issues as well.
It is reasonable to force an upper bound for the various methods of setting
CLOCK_REALTIME. Year 2262 is the absolute upper bound. Assume a maximum
uptime of 30 years which is plenty enough even for esoteric embedded
systems. That results in an upper bound of year 2232 for setting the time.
Once that limit is reached in reality this limit is only a small part of
the problem space. But until then this stops people from trying to paper
over the problem at the wrong places.
Reported-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Reported-by: Hongbo Yao <yaohongbo@huawei.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Stephen Boyd <sboyd@kernel.org> Cc: Miroslav Lichvar <mlichvar@redhat.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1903231125480.2157@nanos.tec.linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
The PLL parameters are computed by looping over the range of acceptable
M, N and E values, and selecting the combination that produces the
output frequency closest to the target. The internal frequency
constraints are taken into account by restricting the tested values for
the PLL parameters, reducing the search space. The target frequency,
however, is only taken into account when computing the post-PLL divider,
which can result in a 0 value for the divider when the PLL output
frequency being tested is lower than half of the target frequency.
Subsequent loops will produce a better set of PLL parameters, but for
some of the iterations this can result in a division by 0.
Fix it by clamping the divider value. We could instead restrict the E
values being tested in the inner loop, but that would require additional
calculation that would likely be less efficient as the E parameter can
only take three different values.
On the D3 SoC the LVDS PHY must be enabled in the same register write
that enables the LVDS output. Skip writing the LVEN bit independently
on that platform, it will be set by the write that sets LVRES.
Commit 0650a91499e0 ("media: mtk-vcodec: Correct return type for mem2mem
buffer helpers") fixed the return types for mem2mem buffer helper
functions by changing a few local variables from vb2_buffer to
vb2_v4l2_buffer. However, it left a few accesses to vb2_buffer::planes
as-is, accidentally turning them into accesses to
vb2_v4l2_buffer::planes and resulting in values being read from/written
to the wrong place.
Fix this by inserting vb2_buf into these accesses so they mimic their
original behavior.
38ac0287b7f4 ("fbdev/efifb: Honour UEFI memory map attributes when mapping the FB")
efifb_probe() checks its memory range via efi_mem_desc_lookup(),
and this leads to a spurious error message:
EFI_MEMMAP is not enabled
at every boot on KVM. This is quite annoying since the error message
appears even if you set "quiet" boot option.
Since this happens on legacy boot, which strangely enough exposes
a EFI framebuffer via screen_info, let's double check that we are
doing an EFI boot before attempting to access the EFI memory map.
Reported-by: Takashi Iwai <tiwai@suse.de> Tested-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Peter Jones <pjones@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/20190328193429.21373-3-ard.biesheuvel@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Smatch marks skb->data as untrusted so it warns that "evt_hdr->dlen"
can copy up to 255 bytes and we only have room for two bytes. Even
if this comes from the firmware and we trust it, the new policy
generally is just to fix it as kernel hardenning.
I can't test this code so I tried to be very conservative. I considered
not allowing "evt_hdr->dlen == 1" because it doesn't initialize the
whole variable but in the end I decided to allow it and manually
initialized "asic_id" and "asic_ver" to zero.
Fixes: e8454ff7b9a4 ("[media] drivers:media:radio: wl128x: FM Driver Common sources") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot is hitting use-after-free bug in uinput module [1]. This is because
kobject_uevent(KOBJ_REMOVE) is called again due to commit 0f4dafc0563c6c49
("Kobject: auto-cleanup on final unref") after memory allocation fault
injection made kobject_uevent(KOBJ_REMOVE) from device_del() from
input_unregister_device() fail, while uinput_destroy_device() is expecting
that kobject_uevent(KOBJ_REMOVE) is not called after device_del() from
input_unregister_device() completed.
That commit intended to catch cases where nobody even attempted to send
"remove" uevents. But there is no guarantee that an event will ultimately
be sent. We are at the point of no return as far as the rest of the kernel
is concerned; there are no repeats or do-overs.
Also, it is not clear whether some subsystem depends on that commit.
If no subsystem depends on that commit, it will be better to remove
the state_{add,remove}_uevent_sent logic. But we don't want to risk
a regression (in a patch which will be backported) by trying to remove
that logic. Therefore, as a first step, let's avoid the use-after-free bug
by making sure that kobject_uevent(KOBJ_REMOVE) won't be triggered twice.
According to hidpp20_batterylevel_get_battery_info my Logitech K270
keyboard reports only 2 battery levels. This matches with what I've seen
after testing with batteries at varying level of fullness, it always
reports either 5% or 30%.
Windows reports "battery good" for the 30% level. I've captured an USB
trace of Windows reading the battery and it is getting the same info
as the Linux hidpp code gets.
Now that Linux handles these devices as hidpp devices, it reports the
battery as being low as it treats anything under 31% as low, this leads
to the user constantly getting a "Keyboard battery is low" warning from
GNOME3, which is very annoying.
This commit fixes this by changing the low threshold to anything under
30%, which I assume is what Windows does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
As a result, change the parent clocks of the Audio-DMAC{0,1} module
clocks on R-Car H3, R-Car M3-W, and R-Car M3-N to S1D2, and change the
parent clock of the Audio-DMAC0 module on R-Car E3 to S1D2.
NOTE: This information will be reflected in a future revision of the
R-Car Gen3 Hardware Manual.
xen_biovec_phys_mergeable() only needs .bv_page of the 2nd bio bvec
for checking if the two bvecs can be merged, so pass page to
xen_biovec_phys_mergeable() directly.
No function change.
Cc: ris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Juergen Gross <jgross@suse.com> Cc: xen-devel@lists.xenproject.org Cc: Omar Sandoval <osandov@fb.com> Cc: Christoph Hellwig <hch@lst.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The use of zero-sized array causes undefined behaviour when it is not
the last member in a structure. As it happens to be in this case.
Also, the current code makes use of a language extension to the C90
standard, but the preferred mechanism to declare variable-length
types such as this one is a flexible array member, introduced in
C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last. Which is beneficial
to cultivate a high-quality code.
Fixes: e48f129c2f20 ("[SCSI] cxgb3i: convert cdev->l2opt to use rcu to prevent NULL dereference") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./sound/soc/codecs/wcd9335.c:5193:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 5183, but without a correspon ding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Vinod Koul <vkoul@kernel.org> Cc: Dan Carpenter <dan.carpenter@oracle.com> (commit_signer:1/11=9%,authored:1/11=9%) Cc: alsa-devel@alsa-project.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./sound/soc/fsl/fsl_utils.c:74:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 38, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Timur Tabi <timur@kernel.org> Cc: Nicolin Chen <nicoleotsuka@gmail.com> Cc: Xiubo Li <Xiubo.Lee@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: alsa-devel@alsa-project.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./sound/soc/fsl/eukrea-tlv320.c:121:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 102, but without a correspo nding object release within this function.
./sound/soc/fsl/eukrea-tlv320.c:127:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 102, but without a correspo nding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: alsa-devel@alsa-project.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As seen on some USB wireless keyboards manufactured by Primax, the HID
parser was using some assumptions that are not always true. In this case
it's s the fact that, inside the scope of a main item, an Usage Page
will always precede an Usage.
The spec is not pretty clear as 6.2.2.7 states "Any usage that follows
is interpreted as a Usage ID and concatenated with the Usage Page".
While 6.2.2.8 states "When the parser encounters a main item it
concatenates the last declared Usage Page with a Usage to form a
complete usage value." Being somewhat contradictory it was decided to
match Window's implementation, which follows 6.2.2.8.
In summary, the patch moves the Usage Page concatenation from the local
item parsing function to the main item parsing function.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Terry Junge <terry.junge@poly.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
arch/sh/include/cpu-sh4/cpu/sh7786.h: In function ‘sh7786_mm_sel’:
arch/sh/include/cpu-sh4/cpu/sh7786.h:135:21: warning: passing argument 1 of ‘__raw_readl’ makes pointer from integer without a cast [-Wint-conversion]
return __raw_readl(0xFC400020) & 0x7;
^~~~~~~~~~
In file included from include/linux/io.h:25:0,
from arch/sh/include/cpu-sh4/cpu/sh7786.h:14,
from drivers/pinctrl/sh-pfc/pfc-sh7786.c:15:
arch/arm/include/asm/io.h:113:21: note: expected ‘const volatile void *’ but argument is of type ‘unsigned int’
#define __raw_readl __raw_readl
^
arch/arm/include/asm/io.h:114:19: note: in expansion of macro ‘__raw_readl’
static inline u32 __raw_readl(const volatile void __iomem *addr)
^~~~~~~~~~~
__raw_readl() on SuperH is a macro that casts the passed I/O address to
the correct type, while the implementations on most other architectures
expect to be passed the correct pointer type.
Add an explicit cast to fix this.
Note that this also gets rid of a sparse warning on SuperH:
arch/sh/include/cpu-sh4/cpu/sh7786.h:135:16: warning: incorrect type in argument 1 (different base types)
arch/sh/include/cpu-sh4/cpu/sh7786.h:135:16: expected void const volatile [noderef] <asn:2>*<noident>
arch/sh/include/cpu-sh4/cpu/sh7786.h:135:16: got unsigned int
port_pd is treated as le32 in declaration and read, fix assignment to be
in le32 too. This change fixes the following compilation warnings.
drivers/infiniband/hw/hns/hns_roce_ah.c:67:24: warning: incorrect type
in assignment (different base types)
drivers/infiniband/hw/hns/hns_roce_ah.c:67:24: expected restricted __le32 [usertype] port_pd
drivers/infiniband/hw/hns/hns_roce_ah.c:67:24: got restricted __be32 [usertype]
Fixes: 9a4435375cd1 ("IB/hns: Add driver files for hns RoCE driver") Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Reviewed-by: Gal Pressman <galpress@amazon.com> Reviewed-by: Lijun Ou <ouliun@huawei.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
