The AMD pinctrl driver uses a chained interrupt to demultiplex the GPIO
interrupts. Kevin Vandeventer reported, that his new AMD Ryzen locks up
hard on boot when the AMD pinctrl driver is initialized. The reason is an
interrupt storm. It's not clear whether that's caused by hardware or
firmware or both.
Using chained interrupts on X86 is a dangerous endavour. If a system is
misconfigured or the hardware buggy there is no safety net to catch an
interrupt storm.
Convert the driver to use a regular interrupt for the demultiplex
handler. This allows the interrupt storm detector to catch the malfunction
and lets the system boot up.
This should be backported to stable because it's likely that more users run
into this problem as the AMD Ryzen machines are spreading.
Jeff Moyer reported that on his system with two memory regions 0~64G and
1T~1T+192G, and kernel option "memmap=192G!1024G" added, enabling KASLR
will make the system hang intermittently during boot. While adding 'nokaslr'
won't.
This crash happens because the for loop count calculation in sync_global_pgds()
is not correct. When a mapping area crosses PGD entries, we should
calculate the starting address of region which next PGD covers and assign
it to next for loop count, but not add PGDIR_SIZE directly. The old
code works right only if the mapping area is an exact multiple of PGDIR_SIZE,
otherwize the end region could be skipped so that it can't be synchronized
to all other processes from kernel PGD init_mm.pgd.
In Jeff's system, emulated pmem area [1024G, 1216G) is smaller than
PGDIR_SIZE. While 'nokaslr' works because PAGE_OFFSET is 1T aligned, it
makes this area be mapped inside one PGD entry. With KASLR enabled,
this area could cross two PGD entries, then the next PGD entry won't
be synced to all other processes. That is why we saw empty PGD.
Fix it.
Reported-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Baoquan He <bhe@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Dave Young <dyoung@redhat.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jinbum Park <jinb.park7@gmail.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Kees Cook <keescook@chromium.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Yasuaki Ishimatsu <yasu.isimatu@gmail.com> Cc: Yinghai Lu <yinghai@kernel.org> Link: http://lkml.kernel.org/r/1493864747-8506-1-git-send-email-bhe@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dm_pool_inc_data_range() fails, dm thin aborts current metadata
transaction and marks pool as PM_READ_ONLY. Memory for thin mapping
is released as well. However, current thin mapping will be queued
onto next stage as part of queue_passdown_pt2() or passdown_endio().
This dangling thin mapping memory when processed and accessed in
next stage will lead to device mapper crashing.
Code flow without fix:
-> process_prepared_discard_passdown_pt1(m)
-> dm_thin_remove_range()
-> discard passdown
--> passdown_endio(m) queues m onto next stage
-> dm_pool_inc_data_range() fails, frees memory m
but does not remove it from next stage queue
-> process_prepared_discard_passdown_pt2(m)
-> processes freed memory m and crashes
The fix is to first take the block ref count for discarded block and
then do a passdown discard of this block. If block ref count fails,
then bail out aborting current metadata transaction, mark pool as
PM_READ_ONLY and also free current thin mapping memory (existing error
handling code) without queueing this thin mapping onto next stage of
processing. If block ref count succeeds, then passdown discard of this
block. Discard callback of passdown_endio() will queue this thin mapping
onto next stage of processing.
Code flow with fix:
-> process_prepared_discard_passdown_pt1(m)
-> dm_thin_remove_range()
-> dm_pool_inc_data_range()
--> if fails, free memory m and bail out
-> discard passdown
--> passdown_endio(m) queues m onto next stage
The hash table created during vmw_cmdbuf_res_man_create was
never freed. This causes memory leak in context creation.
Added the corresponding drm_ht_remove in vmw_cmdbuf_res_man_destroy.
Tested for memory leak by running piglit overnight and kernel
memory is not inflated which earlier was.
If the task calling layoutget is signalled, then it is possible for the
calls to nfs4_sequence_free_slot() and nfs4_layoutget_prepare() to race,
in which case we leak a slot.
The fix is to move the call to nfs4_sequence_free_slot() into the
nfs4_layoutget_release() so that it gets called at task teardown time.
Fixes: 2e80dbe7ac51 ("NFSv4.1: Close callback races for OPEN, LAYOUTGET...") Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have umask support, we shouldn't re-send the mode in a SETATTR
following an exclusive CREATE, or we risk having the same problem fixed in
commit 5334c5bdac92 ("NFS: Send attributes in OPEN request for
NFS4_CREATE_EXCLUSIVE4_1"), which is that files with S_ISGID will have that
bit stripped away.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Fixes: dff25ddb4808 ("nfs: add support for the umask attribute") Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently we met a problem, the codec has valid adcs and input pins,
and they can form valid input paths, but the driver does not build
valid controls for them like "Mic boost", "Capture Volume" and
"Capture Switch".
Through debugging, I found the driver needs to shrink the invalid
adcs and input paths for this machine, so it will move the whole
column bitmap value to the previous column, after moving it, the
driver forgets to set the original column bitmap value to zero, as a
result, the driver will invalidate the path whose index value is the
original colume bitmap value. After executing this function, all
valid input paths are invalidated by a mistake, there are no any
valid input paths, so the driver won't build controls for them.
azx_codec_configure() loops over the codecs found on the given
controller via a linked list. The code used to work in the past, but
in the current version, this may lead to an endless loop when a codec
binding returns an error.
The culprit is that the snd_hda_codec_configure() unregisters the
device upon error, and this eventually deletes the given codec object
from the bus. Since the list is initialized via list_del_init(), the
next object points to the same device itself. This behavior change
was introduced at splitting the HD-audio code code, and forgotten to
adapt it here.
For fixing this bug, just use a *_safe() version of list iteration.
Fixes: d068ebc25e6e ("ALSA: hda - Move some codes up to hdac_bus struct") Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the scheduler sets TIF_NEED_RESCHED & we call into the scheduler
from arch/mips/kernel/entry.S we disable interrupts. This is true
regardless of whether we reach work_resched from syscall_exit_work,
resume_userspace or by looping after calling schedule(). Although we
disable interrupts in these paths we don't call trace_hardirqs_off()
before calling into C code which may acquire locks, and we therefore
leave lockdep with an inconsistent view of whether interrupts are
disabled or not when CONFIG_PROVE_LOCKING & CONFIG_DEBUG_LOCKDEP are
both enabled.
Without tracing this interrupt state lockdep will print warnings such
as the following once a task returns from a syscall via
syscall_exit_partial with TIF_NEED_RESCHED set:
Fix this by using the TRACE_IRQS_OFF macro to call trace_hardirqs_off()
when CONFIG_TRACE_IRQFLAGS is enabled. This is done before invoking
schedule() following the work_resched label because:
1) Interrupts are disabled regardless of the path we take to reach
work_resched() & schedule().
2) Performing the tracing here avoids the need to do it in paths which
disable interrupts but don't call out to C code before hitting a
path which uses the RESTORE_SOME macro that will call
trace_hardirqs_on() or trace_hardirqs_off() as appropriate.
We call trace_hardirqs_on() using the TRACE_IRQS_ON macro before calling
syscall_trace_leave() for similar reasons, ensuring that lockdep has a
consistent view of state after we re-enable interrupts.
We allocate memory for a ready_count variable per-CPU, which is accessed
via a cached non-coherent TLB mapping to perform synchronisation between
threads within the core using LL/SC instructions. In order to ensure
that the variable is contained within its own data cache line we
allocate 2 lines worth of memory & align the resulting pointer to a line
boundary. This is however unnecessary, since kmalloc is guaranteed to
return memory which is at least cache-line aligned (see
ARCH_DMA_MINALIGN). Stop the redundant manual alignment.
Besides cleaning up the code & avoiding needless work, this has the side
effect of avoiding an arithmetic error found by Bryan on 64 bit systems
due to the 32 bit size of the former dlinesz. This led the ready_count
variable to have its upper 32b cleared erroneously for MIPS64 kernels,
causing problems when ready_count was later used on MIPS64 via cpuidle.
Since commit 81a76d7119f6 ("MIPS: Avoid using unwind_stack() with
usermode") show_backtrace() invokes the raw backtracer when
cp0_status & ST0_KSU indicates user mode to fix issues on EVA kernels
where user and kernel address spaces overlap.
However this is used by show_stack() which creates its own pt_regs on
the stack and leaves cp0_status uninitialised in most of the code paths.
This results in the non deterministic use of the raw back tracer
depending on the previous stack content.
show_stack() deals exclusively with kernel mode stacks anyway, so
explicitly initialise regs.cp0_status to KSU_KERNEL (i.e. 0) to ensure
we get a useful backtrace.
Fixes: 81a76d7119f6 ("MIPS: Avoid using unwind_stack() with usermode") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16656/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In this sequence the 'move' is assumed in the delay slot of the 'beq',
but head.S is in reorder mode and the former gets pushed one 'nop'
farther by the assembler.
The corrected behavior made booting with an UHI supplied dtb erratic.
Fixes: 15f37e158892 ("MIPS: store the appended dtb address in a variable") Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com> Reviewed-by: James Hogan <james.hogan@imgtec.com> Cc: Jonas Gorski <jogo@openwrt.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16614/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to use xen_blkif_get()/xen_blkif_put() in the kthread
of xen-blkback. Thread stopping is synchronous and using the blkif
reference counting in the kthread will avoid to ever let the reference
count drop to zero at the end of an I/O running concurrent to
disconnecting and multiple rings.
Setting ring->xenblkd to NULL after stopping the kthread isn't needed
as the kthread does this already.
Signed-off-by: Juergen Gross <jgross@suse.com> Tested-by: Steven Haigh <netwiz@crc.id.au> Acked-by: Roger Pau Monné <roger.pau@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the comments for svc_set_num_threads() said,
" Destroying threads relies on the service threads filling in
rqstp->rq_task, which only the nfs ones do. Assumes the serv
has been created using svc_create_pooled()."
If creating service through svc_create(), the svc_pool_map_put()
will be called in svc_destroy(), but the pool map isn't used.
So that, the reference of pool map will be drop, the next using
of pool map will get a zero npools.
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the creation of connection tracking entry from
netlink when synproxy is used. It was missing the addition of
the synproxy extension.
This was causing kernel crashes when a conntrack entry created by
conntrackd was used after the switch of traffic from active node
to the passive node.
Signed-off-by: Eric Leblond <eric@regit.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Network interface groups support added while ago, however
there is no IFLA_GROUP attribute description in policy
and netlink message size calculations until now.
Add IFLA_GROUP attribute to the policy.
Fixes: cbda10fa97d7 ("net_device: add support for network device groups") Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While commit 73ba57bfae4a ("ipv6: fix backtracking for throw routes")
does good job on error propagation to the fib_rules_lookup()
in fib rules core framework that also corrects throw routes
handling, it does not solve route reference leakage problem
happened when we return -EAGAIN to the fib_rules_lookup()
and leave routing table entry referenced in arg->result.
If rule with matched throw route isn't last matched in the
list we overwrite arg->result losing reference on throw
route stored previously forever.
We also partially revert commit ab997ad40839 ("ipv6: fix the
incorrect return value of throw route") since we never return
routing table entry with dst.error == -EAGAIN when
CONFIG_IPV6_MULTIPLE_TABLES is on. Also there is no point
to check for RTF_REJECT flag since it is always set throw
route.
Fixes: 73ba57bfae4a ("ipv6: fix backtracking for throw routes") Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The register_vlan_device would invoke free_netdev directly, when
register_vlan_dev failed. It would trigger the BUG_ON in free_netdev
if the dev was already registered. In this case, the netdev would be
freed in netdev_run_todo later.
So add one condition check now. Only when dev is not registered, then
free it directly.
The following is the part coredump when netdev_upper_dev_link failed
in register_vlan_dev. I removed the lines which are too long.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the existing dn_route.c code, dn_route_output_slow() takes
dst->__refcnt before calling dn_insert_route() while dn_route_input_slow()
does not take dst->__refcnt before calling dn_insert_route().
This makes the whole routing code very buggy.
In dn_dst_check_expire(), dnrt_free() is called when rt expires. This
makes the routes inserted by dn_route_output_slow() not able to be
freed as the refcnt is not released.
In dn_dst_gc(), dnrt_drop() is called to release rt which could
potentially cause the dst->__refcnt to be dropped to -1.
In dn_run_flush(), dst_free() is called to release all the dst. Again,
it makes the dst inserted by dn_route_output_slow() not able to be
released and also, it does not wait on the rcu and could potentially
cause crash in the path where other users still refer to this dst.
This patch makes sure both input and output path do not take
dst->__refcnt before calling dn_insert_route() and also makes sure
dnrt_free()/dst_free() is called when removing dst from the hash table.
The only difference between those 2 calls is that dnrt_free() waits on
the rcu while dst_free() does not.
Signed-off-by: Wei Wang <weiwan@google.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before attempting to initialize the command interface we must wait till
the fw_initializing bit is clear.
If we fail to meet this condition the hardware will drop our
configuration, specifically the descriptors page address. This scenario
can happen when the firmware is still executing an FLR flow and did not
finish yet so the driver needs to wait for that to finish.
Fixes: e3297246c2c8 ('net/mlx5_core: Wait for FW readiness on startup') Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error flow of mlx5e_create_netdev calls the cleanup call
of the given profile without checking if it exists, fix that.
Currently the VF reps don't register that callback and we crash
if getting into error -- can be reproduced by the user doing ctrl^C
while attempting to change the sriov mode from legacy to switchdev.
The offending commit only changed the code path for PF/VF, but it
didn't take care of VF representors. As a result, since
params->tx_min_inline_mode for VF representors is kzalloced to 0
(MLX5_INLINE_MODE_NONE), all VF reps SQs were set to that mode.
This actually works on CX5 by default but broke CX4. Fix that by
adding a call to query the min inline mode from the VF rep build up code.
Fixes: a6f402e49901 ("net/mlx5e: Tx, no inline copy on ConnectX-5") Signed-off-by: Chris Mi <chrism@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In sctp_for_each_transport, pos is used to save how many objs it has
dumped. Now it gets the last obj by sctp_transport_get_idx, then gets
the next obj by sctp_transport_get_next.
The issue is that in the meanwhile if some objs in transport hashtable
are removed and the objs nums are less than pos, sctp_transport_get_idx
would return NULL and hti.walker.tbl is NULL as well. At this moment
it should stop hti, instead of continue getting the next obj. Or it
would cause a NULL pointer dereference in sctp_transport_get_next.
This patch is to pass pos + 1 into sctp_transport_get_idx to get the
next obj directly, even if pos > objs nums, it would return NULL and
stop hti.
Fixes: 626d16f50f39 ("sctp: export some apis or variables for sctp_diag and reuse some for proc") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now when starting the dad work in addrconf_mod_dad_work, if the dad work
is idle and queued, it needs to hold ifa.
The problem is there's one gap in [1], during which if the pending dad work
is removed elsewhere. It will miss to hold ifa, but the dad word is still
idea and queue.
if (!delayed_work_pending(&ifp->dad_work))
in6_ifa_hold(ifp);
<--------------[1]
mod_delayed_work(addrconf_wq, &ifp->dad_work, delay);
An use-after-free issue can be caused by this.
Chen Wei found this issue when WARN_ON(!hlist_unhashed(&ifp->addr_lst)) in
net6_ifa_finish_destroy was hit because of it.
As Hannes' suggestion, this patch is to fix it by holding ifa first in
addrconf_mod_dad_work, then calling mod_delayed_work and putting ifa if
the dad_work is already in queue.
Note that this patch did not choose to fix it with:
if (!mod_delayed_work(delay))
in6_ifa_hold(ifp);
As with it, when delay == 0, dad_work would be scheduled immediately, all
addrconf_mod_dad_work(0) callings had to be moved under ifp->lock.
Reported-by: Wei Chen <weichen@redhat.com> Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Florian Weimer seems to have a glibc test-case which requires that
loopback interfaces does not get ICMP ratelimited. This was broken by
commit c0303efeab73 ("net: reduce cycles spend on ICMP replies that
gets rate limited").
An ICMP response will usually be routed back-out the same incoming
interface. Thus, take advantage of this and skip global ICMP
ratelimit when the incoming device is loopback. In the unlikely event
that the outgoing it not loopback, due to strange routing policy
rules, ICMP rate limiting still works via peer ratelimiting via
icmpv4_xrlim_allow(). Thus, we should still comply with RFC1812
(section 4.3.2.8 "Rate Limiting").
This seems to fix the reproducer given by Florian. While still
avoiding to perform expensive and unneeded outgoing route lookup for
rate limited packets (in the non-loopback case).
Fixes: c0303efeab73 ("net: reduce cycles spend on ICMP replies that gets rate limited") Reported-by: Florian Weimer <fweimer@redhat.com> Reported-by: "H.J. Lu" <hjl.tools@gmail.com> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new Sierra Wireless EM7305 device ID used in a Toshiba laptop,
and two Longcheer device IDs entries used by Telewell TW-3G HSPA+
branded modems.
Reported-by: Petr Kloc <petr_kloc@yahoo.com> Reported-by: Teemu Likonen <tlikonen@iki.fi> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrey reported a lockdep warning on non-initialized
spinlock:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 1 PID: 4099 Comm: a.out Not tainted 4.12.0-rc6+ #9
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16
dump_stack+0x292/0x395 lib/dump_stack.c:52
register_lock_class+0x717/0x1aa0 kernel/locking/lockdep.c:755
? 0xffffffffa0000000
__lock_acquire+0x269/0x3690 kernel/locking/lockdep.c:3255
lock_acquire+0x22d/0x560 kernel/locking/lockdep.c:3855
__raw_spin_lock_bh ./include/linux/spinlock_api_smp.h:135
_raw_spin_lock_bh+0x36/0x50 kernel/locking/spinlock.c:175
spin_lock_bh ./include/linux/spinlock.h:304
ip_mc_clear_src+0x27/0x1e0 net/ipv4/igmp.c:2076
igmpv3_clear_delrec+0xee/0x4f0 net/ipv4/igmp.c:1194
ip_mc_destroy_dev+0x4e/0x190 net/ipv4/igmp.c:1736
We miss a spin_lock_init() in igmpv3_add_delrec(), probably
because previously we never use it on this code path. Since
we already unlink it from the global mc_tomb list, it is
probably safe not to acquire this spinlock here. It does not
harm to have it although, to avoid conditional locking.
Fixes: c38b7d327aaf ("igmp: acquire pmc lock for ip_mc_clear_src()") Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This happens because we don't hold pmc->lock in ip_mc_clear_src()
and a parallel mr_ifc_timer timer could jump in and access them.
The RCU lock is there but it is merely for pmc itself, this
spinlock could actually ensure we don't access them in parallel.
Thanks to Eric and Long for discussion on this bug.
Reported-by: Andrey Konovalov <andreyknvl@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Xin Long <lucien.xin@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reading /proc/net/snmp6 yields bogus values on 32 bit kernels.
Use "u64" instead of "unsigned long" in sizeof().
Fixes: 4a4857b1c81e ("proc: Reduce cache miss in snmp6_seq_show") Signed-off-by: Christian Perle <christian.perle@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DIM (Dynamically-tuned Interrupt Moderation) is a mechanism designed for
changing the channel interrupt moderation values in order to reduce CPU
overhead for all traffic types.
Each iteration of the algorithm, DIM calculates the difference in
throughput, packet rate and interrupt rate from last iteration in order
to make a decision. DIM relies on counters for each metric. When these
counters get to their type's max value they wraparound. In this case
the delta between 'end' and 'start' samples is negative and when
translated to unsigned integers - very high. This results in a false
indication to the algorithm and might result in a wrong decision.
The fix calculates the 'distance' between 'end' and 'start' samples in a
cyclic way around the relevant type's max value. It can also be viewed as
an absolute value around the type's max value instead of around 0.
Testing show higher stability in DIM profile selection and no wraparound
issues.
Fixes: cb3c7fd4f839 ("net/mlx5e: Support adaptive RX coalescing") Signed-off-by: Tal Gilboa <talgi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DIM (Dynamically-tuned Interrupt Moderation) is a mechanism designed for
changing the channel interrupt moderation values in order to reduce CPU
overhead for all traffic types.
Until now only interrupt and packet rate were sampled.
We found a scenario on which we get a false indication since a change in
DIM caused more aggregation and reduced packet rate while increasing BW.
We now regard a change as succesfull iff:
current_BW > (prev_BW + threshold) or
current_BW ~= prev_BW and current_PR > (prev_PR + threshold) or
current_BW ~= prev_BW and current_PR ~= prev_PR and
current_IR < (prev_IR - threshold)
Where BW = Bandwidth, PR = Packet rate and IR = Interrupt rate
Remove the following module event counters out of ethtool stats. The
reason for removing these event counters is that these events do not
occur without techinician's intervention.
module_pwr_budget_exd
module_long_range
module_no_eeprom
module_enforce_part
module_unknown_id
module_unknown_status
module_plug
Fixes: bedb7c909c19 ("net/mlx5e: Add port module event counters to ethtool stats") Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed by: Gal Pressman <galp@mellanox.com>
The kernel may sleep under a rcu read lock in tipc_msg_reverse, and the
function call path is:
tipc_l2_rcv_msg (acquire the lock by rcu_read_lock)
tipc_rcv
tipc_sk_rcv
tipc_msg_reverse
pskb_expand_head(GFP_KERNEL) --> may sleep
tipc_node_broadcast
tipc_node_xmit_skb
tipc_node_xmit
tipc_sk_rcv
tipc_msg_reverse
pskb_expand_head(GFP_KERNEL) --> may sleep
To fix it, "GFP_KERNEL" is replaced with "GFP_ATOMIC".
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel may sleep under a rcu read lock in cfpkt_create_pfx, and the
function call path is:
cfcnfg_linkup_rsp (acquire the lock by rcu_read_lock)
cfctrl_linkdown_req
cfpkt_create
cfpkt_create_pfx
alloc_skb(GFP_KERNEL) --> may sleep
cfserl_receive (acquire the lock by rcu_read_lock)
cfpkt_split
cfpkt_create_pfx
alloc_skb(GFP_KERNEL) --> may sleep
There is "in_interrupt" in cfpkt_create_pfx to decide use "GFP_KERNEL" or
"GFP_ATOMIC". In this situation, "GFP_KERNEL" is used because the function
is called under a rcu read lock, instead in interrupt.
To fix it, only "GFP_ATOMIC" is used in cfpkt_create_pfx.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now sctp holds read_lock when foreach sctp_ep_hashtable without disabling
BH. If CPU schedules to another thread A at this moment, the thread A may
be trying to hold the write_lock with disabling BH.
As BH is disabled and CPU cannot schedule back to the thread holding the
read_lock, while the thread A keeps waiting for the read_lock. A dead
lock would be triggered by this.
This patch is to fix this dead lock by calling read_lock_bh instead to
disable BH when holding the read_lock in sctp_for_each_endpoint.
Fixes: 626d16f50f39 ("sctp: export some apis or variables for sctp_diag and reuse some for proc") Reported-by: Xiumei Mu <xmu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Message from syslogd@flamingo at Apr 26 00:45:00 ...
kernel:unregister_netdevice: waiting for lo to become free. Usage count = 4
They seem to coincide with net namespace teardown.
The message is emitted by netdev_wait_allrefs().
Forced a kdump in netdev_run_todo, but found that the refcount on the lo
device was already 0 at the time we got to the panic.
Used bcc to check the blocking in netdev_run_todo. The only places
where we're off cpu there are in the rcu_barrier() and msleep() calls.
That behavior is expected. The msleep time coincides with the amount of
time we spend waiting for the refcount to reach zero; the rcu_barrier()
wait times are not excessive.
After looking through the list of callbacks that the netdevice notifiers
invoke in this path, it appears that the dst_dev_event is the most
interesting. The dst_ifdown path places a hold on the loopback_dev as
part of releasing the dev associated with the original dst cache entry.
Most of our notifier callbacks are straight-forward, but this one a)
looks complex, and b) places a hold on the network interface in
question.
I constructed a new bcc script that watches various events in the
liftime of a dst cache entry. Note that dst_ifdown will take a hold on
the loopback device until the invalidated dst entry gets freed.
[ __dst_free] on DST: ffff883ccabb7900 IF tap1008300eth0 invoked at 1282115677036183
__dst_free
rcu_nocb_kthread
kthread
ret_from_fork Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Verify that the caller-provided sockaddr structure is large enough to
contain the sa_family field, before accessing it in bind() and connect()
handlers of the AF_UNIX socket. Since neither syscall enforces a minimum
size of the corresponding memory region, very short sockaddrs (zero or
one byte long) result in operating on uninitialized memory while
referencing .sa_family.
Signed-off-by: Mateusz Jurczyk <mjurczyk@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1aa6c4f6b8cd8 ("net: vrf: Add l3mdev rules on first device create")
adds the l3mdev FIB rule the first time a VRF device is created. However,
it only creates the rule once and only in the namespace the first device
is created - which may not be init_net. Fix by using the net_generic
capability to make the add_fib_rules flag per network namespace.
Fixes: 1aa6c4f6b8cd8 ("net: vrf: Add l3mdev rules on first device create") Reported-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roopa reported attempts to delete a bond device that is referenced in a
multipath route is hanging:
$ ifdown bond2 # ifupdown2 command that deletes virtual devices
unregister_netdevice: waiting for bond2 to become free. Usage count = 2
Steps to reproduce:
echo 1 > /proc/sys/net/ipv6/conf/all/ignore_routes_with_linkdown
ip link add dev bond12 type bond
ip link add dev bond13 type bond
ip addr add 2001:db8:2::0/64 dev bond12
ip addr add 2001:db8:3::0/64 dev bond13
ip route add 2001:db8:33::0/64 nexthop via 2001:db8:2::2 nexthop via 2001:db8:3::2
ip link del dev bond12
ip link del dev bond13
The root cause is the recent change to keep routes on a linkdown. Update
the check to detect when the device is unregistering and release the
route for that case.
Fixes: a1a22c12060e4 ("net: ipv6: Keep nexthop of multipath route on admin down") Reported-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David Ahern <dsahern@gmail.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the structure's fields are not initialized by the
rtnetlink. If driver doesn't set those in ndo_get_vf_config(),
they'd leak memory to user.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> CC: Michal Schmidt <mschmidt@redhat.com> Reviewed-by: Greg Rose <gvrose8192@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Verify that the length of the socket buffer is sufficient to cover the
nlmsghdr structure before accessing the nlh->nlmsg_len field for further
input sanitization. If the client only supplies 1-3 bytes of data in
sk_buff, then nlh->nlmsg_len remains partially uninitialized and
contains leftover memory from the corresponding kernel allocation.
Operating on such data may result in indeterminate evaluation of the
nlmsg_len < sizeof(*nlh) expression.
The bug was discovered by a runtime instrumentation designed to detect
use of uninitialized memory in the kernel. The patch prevents this and
other similar tools (e.g. KMSAN) from flagging this behavior in the future.
Signed-off-by: Mateusz Jurczyk <mjurczyk@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change to remove free_netdev() from ieee80211_if_free()
erroneously didn't add the necessary free_netdev() for when
ieee80211_if_free() is called directly in one place, rather
than as the priv_destructor. Add the missing call.
Fixes: cf124db566e6 ("net: Fix inconsistent teardown and release of private netdev state.") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KMSAN reported a use of uninitialized memory in dev_set_alias(),
which was caused by calling strlcpy() (which in turn called strlen())
on the user-supplied non-terminated string.
Signed-off-by: Alexander Potapenko <glider@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c: In function
'brcmf_usb_probe_phase2':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c:1198:2:
warning: 'devinfo' may be used uninitialized in this function
[-Wmaybe-uninitialized]
mutex_unlock(&devinfo->dev_init_lock);
Fixes: 6d0507a777fb ("brcmfmac: add parameter to pass error code in firmware callback") Cc: Stephen Rothwell <sfr@canb.auug.org.au> Reported-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch in the Fixes references COMPAT_XT_ALIGN in the definition
of XT_DATA_TO_USER, outside an #ifdef CONFIG_COMPAT block.
Split XT_DATA_TO_USER into separate compat and non compat variants and
define the first inside an CONFIG_COMPAT block.
This simplifies both variants by removing branches inside the macro.
Fixes: 324318f0248c ("netfilter: xtables: zero padding in data_to_user") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Cc: Florian Westphal <fw@strlen.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When looking up an iptables rule, the iptables binary compares the
aligned match and target data (XT_ALIGN). In some cases this can
exceed the actual data size to include padding bytes.
Before commit f77bc5b23fb1 ("iptables: use match, target and data
copy_to_user helpers") the malloc()ed bytes were overwritten by the
kernel with kzalloced contents, zeroing the padding and making the
comparison succeed. After this patch, the kernel copies and clears
only data, leaving the padding bytes undefined.
Extend the clear operation from data size to aligned data size to
include the padding bytes, if any.
Padding bytes can be observed in both match and target, and the bug
triggered, by issuing a rule with match icmp and target ACCEPT:
iptables -t mangle -A INPUT -i lo -p icmp --icmp-type 1 -j ACCEPT
iptables -t mangle -D INPUT -i lo -p icmp --icmp-type 1 -j ACCEPT
Fixes: f77bc5b23fb1 ("iptables: use match, target and data copy_to_user helpers") Reported-by: Paul Moore <pmoore@redhat.com> Reported-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Cc: Florian Westphal <fw@strlen.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Marvell driver incorrectly provides phydev->lp_advertising as the
logical and of the link partner's advert and our advert. This is
incorrect - this field is supposed to store the link parter's unmodified
advertisment.
This allows ethtool to report the correct link partner auto-negotiation
status.
Fixes: be937f1f89ca ("Marvell PHY m88e1111 driver fix") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic SPI code calculates how long the issued transfer would take
and adds 100ms in addition to the timeout as tolerance. On my 500 MHz
Lantiq Mips SoC I am getting timeouts from the SPI like this when the
system boots up:
m25p80 spi32766.4: SPI transfer timed out
blk_update_request: I/O error, dev mtdblock3, sector 2
SQUASHFS error: squashfs_read_data failed to read block 0x6e
After increasing the tolerance for the timeout to 200ms I haven't seen
these SPI transfer time outs any more.
The Lantiq SPI driver in use here has an extra work queue in between,
which gets triggered when the controller send the last word and the
hardware FIFOs used for reading and writing are only 8 words long.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Companion descriptor is only used for SuperSpeed endpoints,
if the endpoints are HighSpeed or FullSpeed, the Companion
descriptor will not allocated, so we can only access it if
gadget is SuperSpeed.
I can reproduce this issue on Rockchip platform rk3368 SoC
which supports USB 2.0, and use functionfs for ADB. Kernel
build with CONFIG_KASAN=y and CONFIG_SLUB_DEBUG=y report
the following BUG:
==================================================================
BUG: KASAN: slab-out-of-bounds in ffs_func_set_alt+0x224/0x3a0 at addr ffffffc0601f6509
Read of size 1 by task swapper/0/0
============================================================================
BUG kmalloc-256 (Not tainted): kasan: bad access detected
----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Allocated in ffs_func_bind+0x52c/0x99c age=1275 cpu=0 pid=1
alloc_debug_processing+0x128/0x17c
___slab_alloc.constprop.58+0x50c/0x610
__slab_alloc.isra.55.constprop.57+0x24/0x34
__kmalloc+0xe0/0x250
ffs_func_bind+0x52c/0x99c
usb_add_function+0xd8/0x1d4
configfs_composite_bind+0x48c/0x570
udc_bind_to_driver+0x6c/0x170
usb_udc_attach_driver+0xa4/0xd0
gadget_dev_desc_UDC_store+0xcc/0x118
configfs_write_file+0x1a0/0x1f8
__vfs_write+0x64/0x174
vfs_write+0xe4/0x200
SyS_write+0x68/0xc8
el0_svc_naked+0x24/0x28
INFO: Freed in inode_doinit_with_dentry+0x3f0/0x7c4 age=1275 cpu=7 pid=247
...
Call trace:
[<ffffff900808aab4>] dump_backtrace+0x0/0x230
[<ffffff900808acf8>] show_stack+0x14/0x1c
[<ffffff90084ad420>] dump_stack+0xa0/0xc8
[<ffffff90082157cc>] print_trailer+0x188/0x198
[<ffffff9008215948>] object_err+0x3c/0x4c
[<ffffff900821b5ac>] kasan_report+0x324/0x4dc
[<ffffff900821aa38>] __asan_load1+0x24/0x50
[<ffffff90089eb750>] ffs_func_set_alt+0x224/0x3a0
[<ffffff90089d3760>] composite_setup+0xdcc/0x1ac8
[<ffffff90089d7394>] android_setup+0x124/0x1a0
[<ffffff90089acd18>] _setup+0x54/0x74
[<ffffff90089b6b98>] handle_ep0+0x3288/0x4390
[<ffffff90089b9b44>] dwc_otg_pcd_handle_out_ep_intr+0x14dc/0x2ae4
[<ffffff90089be85c>] dwc_otg_pcd_handle_intr+0x1ec/0x298
[<ffffff90089ad680>] dwc_otg_pcd_irq+0x10/0x20
[<ffffff9008116328>] handle_irq_event_percpu+0x124/0x3ac
[<ffffff9008116610>] handle_irq_event+0x60/0xa0
[<ffffff900811af30>] handle_fasteoi_irq+0x10c/0x1d4
[<ffffff9008115568>] generic_handle_irq+0x30/0x40
[<ffffff90081159b4>] __handle_domain_irq+0xac/0xdc
[<ffffff9008080e9c>] gic_handle_irq+0x64/0xa4
...
Memory state around the buggy address: ffffffc0601f6400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffffffc0601f6480: 00 00 00 00 00 00 00 00 00 00 06 fc fc fc fc fc
>ffffffc0601f6500: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^ ffffffc0601f6580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffffffc0601f6600: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00
==================================================================
Signed-off-by: William Wu <william.wu@rock-chips.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Jerry Zhang <zhangjerry@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I reordered the logic a bit in that IOCTL, but that broke userspace
since it'll get the new mode list, but not the new property values.
Fix that again.
v2: Fix up the error path handling when copy_to_user for the modes
failes (Dhinakaran).
Fixes: 91eefc05f0ac ("drm: Tighten locking in drm_mode_getconnector") Cc: Sean Paul <seanpaul@chromium.org> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: David Airlie <airlied@linux.ie> Cc: dri-devel@lists.freedesktop.org Reported-by: "H.J. Lu" <hjl.tools@gmail.com> Tested-by: "H.J. Lu" <hjl.tools@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100576 Cc: "H.J. Lu" <hjl.tools@gmail.com> Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com> Reviewed-by: Sean Paul <seanpaul@chromium.org> Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170620202837.1701-1-daniel.vetter@ffwll.ch Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a kerberos 5 ticket is being decoded so that it can be loaded into an
rxrpc-type key, there are several places in which the length of a
variable-length field is checked to make sure that it's not going to
overrun the available data - but the data is padded to the nearest
four-byte boundary and the code doesn't check for this extra. This could
lead to the size-remaining variable wrapping and the data pointer going
over the end of the buffer.
Fix this by making the various variable-length data checks use the padded
length.
Reported-by: 石磊 <shilei-c@360.cn> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.c.dionne@auristor.com> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f406270bf73d ("ACPI / scan: Set the visited flag for all
enumerated devices") caused that two group of special SPI or I2C
devices do not enumerate. SPI and I2C devices are expected to be
enumerated by the SPI and I2C subsystems but change caused that
acpi_bus_attach() marks those devices with acpi_device_set_enumerated().
First group of devices are matched using Device Tree compatible property
with special _HID "PRP0001". Those devices have matched scan handler,
acpi_scan_attach_handler() retuns 1 and acpi_bus_attach() marks them
with acpi_device_set_enumerated().
Second group of devices without valid _HID such as "LNXVIDEO" have
device->pnp.type.platform_id set to zero and change again marks them
with acpi_device_set_enumerated().
Fix this by flagging the SPI and I2C devices during struct acpi_device
object initialization time and let the code in acpi_bus_attach() to go
through the device_attach() and acpi_default_enumeration() path for all
SPI and I2C devices.
Fixes: f406270bf73d (ACPI / scan: Set the visited flag for all enumerated devices) Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code in acpi_bus_attach() is inconsistent with respect
to device objects with ACPI drivers bound to them, as it allows
ACPI drivers to bind to device objects with existing "physical"
device companions, but it doesn't allow "physical" device objects
to be created for ACPI device objects with ACPI drivers bound to
them. Thus, in some cases, the outcome depends on the ordering
of events which is confusing at best.
For this reason, modify acpi_bus_attach() to call
acpi_default_enumeration() for device objects with the
pnp.type.platform_id flag set regardless of whether or not
any ACPI drivers are bound to them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Joey Lee <jlee@suse.com> Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When iscsi WRITE underflow occurs there are two different scenarios
that can happen.
Normally in practice, when an EDTL vs. SCSI CDB TRANSFER LENGTH
underflow is detected, the iscsi immediate data payload is the
smaller SCSI CDB TRANSFER LENGTH.
That is, when a host fabric LLD is using a fixed size EDTL for
a specific control CDB, the SCSI CDB TRANSFER LENGTH and actual
SCSI payload ends up being smaller than EDTL. In iscsi, this
means the received iscsi immediate data payload matches the
smaller SCSI CDB TRANSFER LENGTH, because there is no more
SCSI payload to accept beyond SCSI CDB TRANSFER LENGTH.
However, it's possible for a malicous host to send a WRITE
underflow where EDTL is larger than SCSI CDB TRANSFER LENGTH,
but incoming iscsi immediate data actually matches EDTL.
In the wild, we've never had a iscsi host environment actually
try to do this.
For this special case, it's wrong to truncate part of the
control CDB payload and continue to process the command during
underflow when immediate data payload received was larger than
SCSI CDB TRANSFER LENGTH, so go ahead and reject and drop the
bogus payload as a defensive action.
Note this potential bug was originally relaxed by the following
for allowing WRITE underflow in MSFT FCP host environments:
target: allow underflow/overflow for PR OUT etc. commands
Cc: Roland Dreier <roland@purestorage.com> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a BUG() in iscsit_close_session() that could be
triggered when iscsit_logout_post_handler() execution from within
tx thread context was not run for more than SECONDS_FOR_LOGOUT_COMP
(15 seconds), and the TCP connection didn't already close before
then forcing tx thread context to automatically exit.
This would manifest itself during explicit logout as:
[33206.974254] 1 connection(s) still exist for iSCSI session to iqn.1993-08.org.debian:01:3f5523242179
[33206.980184] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 2100.772 msecs
[33209.078643] ------------[ cut here ]------------
[33209.078646] kernel BUG at drivers/target/iscsi/iscsi_target.c:4346!
Normally when explicit logout attempt fails, the tx thread context
exits and iscsit_close_connection() from rx thread context does the
extra cleanup once it detects conn->conn_logout_remove has not been
cleared by the logout type specific post handlers.
To address this special case, if the logout post handler in tx thread
context detects conn->tx_thread_active has already been cleared, simply
return and exit in order for existing iscsit_close_connection()
logic from rx thread context do failed logout cleanup.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com> Tested-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Sagi Grimberg <sagig@mellanox.com> Tested-by: Gary Guo <ghg@datera.io> Tested-by: Chu Yuan Lin <cyl@datera.io> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a se_cmd->cmd_kref underflow during CMD_T_ABORTED
when a fabric driver drops it's second reference from below the
target_core_tmr.c based callers of transport_cmd_finish_abort().
Recently with the conversion of kref to refcount_t, this bug was
manifesting itself as:
[705519.601034] refcount_t: underflow; use-after-free.
[705519.604034] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 20116.512 msecs
[705539.719111] ------------[ cut here ]------------
[705539.719117] WARNING: CPU: 3 PID: 26510 at lib/refcount.c:184 refcount_sub_and_test+0x33/0x51
Since the original kref atomic_t based kref_put() didn't check for
underflow and only invoked the final callback when zero was reached,
this bug did not manifest in practice since all se_cmd memory is
using preallocated tags.
To address this, go ahead and propigate the existing return from
transport_put_cmd() up via transport_cmd_finish_abort(), and
change transport_cmd_finish_abort() + core_tmr_handle_tas_abort()
callers to only do their local target_put_sess_cmd() if necessary.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com> Tested-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Tested-by: Gary Guo <ghg@datera.io> Tested-by: Chu Yuan Lin <cyl@datera.io> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently vDSO support for CLOCK_MONOTONIC_RAW was added in 49eea433b326 ("arm64: Add support for CLOCK_MONOTONIC_RAW in
clock_gettime() vDSO"). Noticing that the core timekeeping code
never set tkr_raw.xtime_nsec, the vDSO implementation didn't
bother exposing it via the data page and instead took the
unshifted tk->raw_time.tv_nsec value which was then immediately
shifted left in the vDSO code.
Unfortunately, by accellerating the MONOTONIC_RAW clockid, it
uncovered potential 1ns time inconsistencies caused by the
timekeeping core not handing sub-ns resolution.
Now that the core code has been fixed and is actually setting
tkr_raw.xtime_nsec, we need to take that into account in the
vDSO by adding it to the shifted raw_time value, in order to
fix the user-visible inconsistency. Rather than do that at each
use (and expand the data page in the process), instead perform
the shift/addition operation when populating the data page and
remove the shift from the vDSO code entirely.
[jstultz: minor whitespace tweak, tried to improve commit
message to make it more clear this fixes a regression] Reported-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Tested-by: Daniel Mentz <danielmentz@google.com> Acked-by: Kevin Brodsky <kevin.brodsky@arm.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Stephen Boyd <stephen.boyd@linaro.org> Cc: Miroslav Lichvar <mlichvar@redhat.com> Link: http://lkml.kernel.org/r/1496965462-20003-4-git-send-email-john.stultz@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to how the MONOTONIC_RAW accumulation logic was handled,
there is the potential for a 1ns discontinuity when we do
accumulations. This small discontinuity has for the most part
gone un-noticed, but since ARM64 enabled CLOCK_MONOTONIC_RAW
in their vDSO clock_gettime implementation, we've seen failures
with the inconsistency-check test in kselftest.
This patch addresses the issue by using the same sub-ns
accumulation handling that CLOCK_MONOTONIC uses, which avoids
the issue for in-kernel users.
Since the ARM64 vDSO implementation has its own clock_gettime
calculation logic, this patch reduces the frequency of errors,
but failures are still seen. The ARM64 vDSO will need to be
updated to include the sub-nanosecond xtime_nsec values in its
calculation for this issue to be completely fixed.
Signed-off-by: John Stultz <john.stultz@linaro.org> Tested-by: Daniel Mentz <danielmentz@google.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Kevin Brodsky <kevin.brodsky@arm.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Stephen Boyd <stephen.boyd@linaro.org> Cc: Will Deacon <will.deacon@arm.com> Cc: Miroslav Lichvar <mlichvar@redhat.com> Link: http://lkml.kernel.org/r/1496965462-20003-3-git-send-email-john.stultz@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is called from the core timekeeping code via:
cycle_now = tkr->read(tkr->clock);
tkr->read is the cached tkr->clock->read() function pointer.
When the clocksource is changed then tkr->clock and tkr->read
are updated sequentially. The code above results in a sequential
load operation of tkr->read and tkr->clock as well.
If the store to tkr->clock hits between the loads of tkr->read
and tkr->clock, then the old read() function is called with the
new clock pointer. As a consequence the read() function
dereferences a different data structure and the resulting 'reg'
pointer can point anywhere including NULL.
This problem was introduced when the timekeeping code was
switched over to use struct tk_read_base. Before that, it was
theoretically possible as well when the compiler decided to
reload clock in the code sequence:
now = tk->clock->read(tk->clock);
Add a helper function which avoids the issue by reading
tk_read_base->clock once into a local variable clk and then issue
the read function via clk->read(clk). This guarantees that the
read() function always gets the proper clocksource pointer handed
in.
Since there is now no use for the tkr.read pointer, this patch
also removes it, and to address stopping the fast timekeeper
during suspend/resume, it introduces a dummy clocksource to use
rather then just a dummy read function.
Signed-off-by: John Stultz <john.stultz@linaro.org> Acked-by: Ingo Molnar <mingo@kernel.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Stephen Boyd <stephen.boyd@linaro.org> Cc: Miroslav Lichvar <mlichvar@redhat.com> Cc: Daniel Mentz <danielmentz@google.com> Link: http://lkml.kernel.org/r/1496965462-20003-2-git-send-email-john.stultz@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When request firmware fails, brcmf_ops_sdio_remove is being called and
brcmf_bus freed. In such circumstancies if you do a suspend/resume cycle
the kernel hangs on resume due a NULL pointer dereference in resume
function. So in brcmf_sdio_firmware_callback() we need to unbind the
driver from both sdio_func devices when firmware load failure is indicated.
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When firmware loading failed the code used to unbind the device provided
by the calling code. However, for the sdio driver two devices are bound
and both need to be released upon failure. The callback has been extended
with parameter to pass error code so add that in this commit upon firmware
loading failure.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the parameters in the firmware callback so it can be called
upon success and failure. This allows the caller to properly clear
all resources in the failure path. Right now the error code is
always zero, ie. success.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Power9, trying to use data breakpoints throws the splat shown
below. This is because the check for a data breakpoint in DSISR is in
do_hash_page(), which is not called when in Radix mode.
Move the check to handle_page_fault() so as to catch data breakpoints
in both Hash and Radix MMU modes.
We have to change the check in do_hash_page() against 0xa410 to use
0xa450, so as to include the value of (DSISR_DABRMATCH << 16).
There are two sites that call handle_page_fault() when in Radix, both
already pass DSISR in r4.
Fixes: caca285e5ab4 ("powerpc/mm/radix: Use STD_MMU_64 to properly isolate hash related code") Reported-by: Shriya R. Kulkarni <shriykul@in.ibm.com> Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
[mpe: Fix the fall-through case on hash, we need to reload DSISR] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a crash when function_graph and jprobes are used together.
This is essentially commit 237d28db036e ("ftrace/jprobes/x86: Fix
conflict between jprobes and function graph tracing"), but for powerpc.
Jprobes breaks function_graph tracing since the jprobe hook needs to use
jprobe_return(), which never returns back to the hook, but instead to
the original jprobe'd function. The solution is to momentarily pause
function_graph tracing before invoking the jprobe hook and re-enable it
when returning back to the original jprobe'd function.
Fixes: 6794c78243bf ("powerpc64: port of the function graph tracer") Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner wrote:
> The CRIU support added a 'feature' which allows a user space task to send
> arbitrary (kernel) signals to itself. The changelog says:
>
> The kernel prevents sending of siginfo with positive si_code, because
> these codes are reserved for kernel. I think we can allow a task to
> send such a siginfo to itself. This operation should not be dangerous.
>
> Quite contrary to that claim, it turns out that it is outright dangerous
> for signals with info->si_code == SI_TIMER. The following code sequence in
> a user space task allows to crash the kernel:
>
> id = timer_create(CLOCK_XXX, ..... signo = SIGX);
> timer_set(id, ....);
> info->si_signo = SIGX;
> info->si_code = SI_TIMER:
> info->_sifields._timer._tid = id;
> info->_sifields._timer._sys_private = 2;
> rt_[tg]sigqueueinfo(..., SIGX, info);
> sigemptyset(&sigset);
> sigaddset(&sigset, SIGX);
> rt_sigtimedwait(sigset, info);
>
> For timers based on CLOCK_PROCESS_CPUTIME_ID, CLOCK_THREAD_CPUTIME_ID this
> results in a kernel crash because sigwait() dequeues the signal and the
> dequeue code observes:
>
> info->si_code == SI_TIMER && info->_sifields._timer._sys_private != 0
>
> which triggers the following callchain:
>
> do_schedule_next_timer() -> posix_cpu_timer_schedule() -> arm_timer()
>
> arm_timer() executes a list_add() on the timer, which is already armed via
> the timer_set() syscall. That's a double list add which corrupts the posix
> cpu timer list. As a consequence the kernel crashes on the next operation
> touching the posix cpu timer list.
>
> Posix clocks which are internally implemented based on hrtimers are not
> affected by this because hrtimer_start() can handle already armed timers
> nicely, but it's a reliable way to trigger the WARN_ON() in
> hrtimer_forward(), which complains about calling that function on an
> already armed timer.
This problem has existed since the posix timer code was merged into
2.5.63. A few releases earlier in 2.5.60 ptrace gained the ability to
inject not just a signal (which linux has supported since 1.0) but the
full siginfo of a signal.
The core problem is that the code will reschedule in response to
signals getting dequeued not just for signals the timers sent but
for other signals that happen to a si_code of SI_TIMER.
Avoid this confusion by testing to see if the queued signal was
preallocated as all timer signals are preallocated, and so far
only the timer code preallocates signals.
Move the check for if a timer needs to be rescheduled up into
collect_signal where the preallocation check must be performed,
and pass the result back to dequeue_signal where the code reschedules
timers. This makes it clear why the code cares about preallocated
timers.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
History Tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Reference: 66dd34ad31e5 ("signal: allow to send any siginfo to itself")
Reference: 1669ce53e2ff ("Add PTRACE_GETSIGINFO and PTRACE_SETSIGINFO") Fixes: db8b50ba75f2 ("[PATCH] POSIX clocks & timers") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Odd versions of gcc for the sh4 architecture will actually warn about
flags being used while uninitialized, so we set them to zero. Non crazy
gccs will optimize that out again, so it doesn't make a difference.
Next, over aggressive gccs could inline the expression that defines
use_lock, which could then introduce a race resulting in a lock
imbalance. By using READ_ONCE, we prevent that fate. Finally, we make
that assignment const, so that gcc can still optimize a nice amount.
Finally, we fix a potential deadlock between primary_crng.lock and
batched_entropy_reset_lock, where they could be called in opposite
order. Moving the call to invalidate_batched_entropy to outside the lock
rectifies this issue.
Fixes: b169c13de473a85b3c859bb36216a4cb5f00a54a Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the module initialisation there is a possible race
(basically race between uld and lld) where neither the uld
nor lld notifies the uP about where to route the ctrl queue
completions. LLD skips notifying uP as the rdma queues were
not created by then (will leave it to ULD to notify the uP).
As the ULD comes up, it also skips notifying the uP as the
flag FULL_INIT_DONE is not set yet (ULD assumes that the
interface is not up yet).
Consequently, this race between uld and lld leaves uP
unnotified about where to send the ctrl queue completions
to, leading to iwarp RI_RES WR failure.
Here is the race:
CPU 0 CPU1
- allocates nic rx queus
- t4_sge_alloc_ctrl_txq()
(if rdma rsp queues exists,
tell uP to route ctrl queue
compl to rdma rspq)
- acquires the mutex_lock
- allocates rdma response queues
- if FULL_INIT_DONE set,
tell uP to route ctrl queue compl
to rdma rspq
- relinquishes mutex_lock
- acquires the mutex_lock
- enable_rx()
- set FULL_INIT_DONE
- relinquishes mutex_lock
This patch fixes the above issue.
Fixes: e7519f9926f1('cxgb4: avoid enabling napi twice to the same queue') Signed-off-by: Raju Rangoju <rajur@chelsio.com> Acked-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Downgrade the loglevel for SMB2 to prevent filling the log
with messages if e.g. readdir was interrupted. Also make SMB2
and SMB1 codepaths do the same logging during readdir.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At present, HV KVM on POWER8 and POWER9 machines loses any instruction
or data breakpoint set in the host whenever a guest is run.
Instruction breakpoints are currently only used by xmon, but ptrace
and the perf_event subsystem can set data breakpoints as well as xmon.
To fix this, we save the host values of the debug registers (CIABR,
DAWR and DAWRX) before entering the guest and restore them on exit.
To provide space to save them in the stack frame, we expand the stack
frame allocated by kvmppc_hv_entry() from 112 to 144 bytes.
Fixes: b005255e12a3 ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08) Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This restores several special-purpose registers (SPRs) to sane values
on guest exit that were missed before.
TAR and VRSAVE are readable and writable by userspace, and we need to
save and restore them to prevent the guest from potentially affecting
userspace execution (not that TAR or VRSAVE are used by any known
program that run uses the KVM_RUN ioctl). We save/restore these
in kvmppc_vcpu_run_hv() rather than on every guest entry/exit.
FSCR affects userspace execution in that it can prohibit access to
certain facilities by userspace. We restore it to the normal value
for the task on exit from the KVM_RUN ioctl.
IAMR is normally 0, and is restored to 0 on guest exit. However,
with a radix host on POWER9, it is set to a value that prevents the
kernel from executing user-accessible memory. On POWER9, we save
IAMR on guest entry and restore it on guest exit to the saved value
rather than 0. On POWER8 we continue to set it to 0 on guest exit.
PSPB is normally 0. We restore it to 0 on guest exit to prevent
userspace taking advantage of the guest having set it non-zero
(which would allow userspace to set its SMT priority to high).
UAMOR is normally 0. We restore it to 0 on guest exit to prevent
the AMR from being used as a covert channel between userspace
processes, since the AMR is not context-switched at present.
Fixes: b005255e12a3 ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08) Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds code to save the values of three SPRs (special-purpose
registers) used by userspace to control event-based branches (EBBs),
which are essentially interrupts that get delivered directly to
userspace. These registers are loaded up with guest values when
entering the guest, and their values are saved when exiting the
guest, but we were not saving the host values and restoring them
before going back to userspace.
On POWER8 this would only affect userspace programs which explicitly
request the use of EBBs and also use the KVM_RUN ioctl, since the
only source of EBBs on POWER8 is the PMU, and there is an explicit
enable bit in the PMU registers (and those PMU registers do get
properly context-switched between host and guest). On POWER9 there
is provision for externally-generated EBBs, and these are not subject
to the control in the PMU registers.
Since these registers only affect userspace, we can save them when
we first come in from userspace and restore them before returning to
userspace, rather than saving/restoring the host values on every
guest entry/exit. Similarly, we don't need to worry about their
values on offline secondary threads since they execute in the context
of the idle task, which never executes in userspace.
Fixes: b005255e12a3 ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08) Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
POWER9 DD1 has an erratum where writing to the TBU40 register, which
is used to apply an offset to the timebase, can cause the timebase to
lose counts. This results in the timebase on some CPUs getting out of
sync with other CPUs, which then results in misbehaviour of the
timekeeping code.
To work around the problem, we make KVM ignore the timebase offset for
all guests on POWER9 DD1 machines. This means that live migration
cannot be supported on POWER9 DD1 machines.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If userspace attempts to call the KVM_RUN ioctl when it has hardware
transactional memory (HTM) enabled, the values that it has put in the
HTM-related SPRs TFHAR, TFIAR and TEXASR will get overwritten by
guest values. To fix this, we detect this condition and save those
SPR values in the thread struct, and disable HTM for the task. If
userspace goes to access those SPRs or the HTM facility in future,
a TM-unavailable interrupt will occur and the handler will reload
those SPRs and re-enable HTM.
If userspace has started a transaction and suspended it, we would
currently lose the transactional state in the guest entry path and
would almost certainly get a "TM Bad Thing" interrupt, which would
cause the host to crash. To avoid this, we detect this case and
return from the KVM_RUN ioctl with an EINVAL error, with the KVM
exit reason set to KVM_EXIT_FAIL_ENTRY.
Fixes: b005255e12a3 ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08) Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
POWER9 introduces a new mode for the decrementer register, called
large decrementer mode, in which the decrementer counter is 56 bits
wide rather than 32, and reads are sign-extended rather than
zero-extended. For the decrementer, this new mode is optional and
controlled by a bit in the LPCR. The hypervisor decrementer (HDEC)
is 56 bits wide on POWER9 and has no mode control.
Since KVM code reads and writes the decrementer and hypervisor
decrementer registers in a few places, it needs to be aware of the
need to treat the decrementer value as a 64-bit quantity, and only do
a 32-bit sign extension when large decrementer mode is not in effect.
Similarly, the HDEC should always be treated as a 64-bit quantity on
POWER9. We define a new EXTEND_HDEC macro to encapsulate the feature
test for POWER9 and the sign extension.
To enable the sign extension to be removed in large decrementer mode,
we test the LPCR_LD bit in the host LPCR image stored in the struct
kvm for the guest. If is set then large decrementer mode is enabled
and the sign extension should be skipped.
This is partly based on an earlier patch by Oliver O'Halloran.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For real-space designation asces the asce origin part is only a token.
The asce token origin must not be used to generate an effective
address for storage references. This however is erroneously done
within kvm_s390_shadow_tables().
Furthermore within the same function the wrong parts of virtual
addresses are used to generate a corresponding real address
(e.g. the region second index is used as region first index).
Both of the above can result in incorrect address translations. Only
for real space designations with a token origin of zero and addresses
below one megabyte the translation was correct.
Furthermore replace a "!asce.r" statement with a "!*fake" statement to
make it more obvious that a specific condition has nothing to do with
the architecture, but with the fake handling of real space designations.
Fixes: 3218f7094b6b ("s390/mm: support real-space for gmap shadows") Cc: David Hildenbrand <david@redhat.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes a "maybe-uninitialized" build failure in
arch/mips/kvm/tlb.c when KVM, DYNAMIC_DEBUG and JUMP_LABEL are all
enabled. The failure is:
In file included from ./include/linux/printk.h:329:0,
from ./include/linux/kernel.h:13,
from ./include/asm-generic/bug.h:15,
from ./arch/mips/include/asm/bug.h:41,
from ./include/linux/bug.h:4,
from ./include/linux/thread_info.h:11,
from ./include/asm-generic/current.h:4,
from ./arch/mips/include/generated/asm/current.h:1,
from ./include/linux/sched.h:11,
from arch/mips/kvm/tlb.c:13:
arch/mips/kvm/tlb.c: In function ‘kvm_mips_host_tlb_inv’:
./include/linux/dynamic_debug.h:126:3: error: ‘idx_kernel’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
__dynamic_pr_debug(&descriptor, pr_fmt(fmt), \
^~~~~~~~~~~~~~~~~~
arch/mips/kvm/tlb.c:169:16: note: ‘idx_kernel’ was declared here
int idx_user, idx_kernel;
^~~~~~~~~~
There is a similar error relating to "idx_user". Both errors were
observed with GCC 6.
As far as I can tell, it is impossible for either idx_user or idx_kernel
to be uninitialized when they are later read in the calls to kvm_debug,
but to satisfy the compiler, add zero initializers to both variables.
Signed-off-by: James Cowgill <James.Cowgill@imgtec.com> Fixes: 57e3869cfaae ("KVM: MIPS/TLB: Generalise host TLB invalidate to kernel ASID") Acked-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TF is handled a bit differently for syscall and sysret, compared
to the other instructions: TF is checked after the instruction completes,
so that the OS can disable #DB at a syscall by adding TF to FMASK.
When the sysret is executed the #DB is taken "as if" the syscall insn
just completed.
KVM emulates syscall so that it can trap 32-bit syscall on Intel processors.
Fix the behavior, otherwise you could get #DB on a user stack which is not
nice. This does not affect Linux guests, as they use an IST or task gate
for #DB.
This fixes CVE-2017-7518.
Reported-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 613f050d68a8 ("perf probe: Fix to probe on gcc generated
functions in modules"), the offset from symbol is, incorrectly, added
to the trace point address. This leads to incorrect probe trace points
for inlined functions and when using relative line number on symbols.
Using 'pfunct', a tool found in the 'dwarves' package [1], one can ask what are
the functions that while not being explicitely marked as inline, were inlined
by the compiler:
Now lets concentrate on the 'e1000_consume_page' one, that was inlined twice in
e1000_clean_jumbo_rx_irq(), lets see what readelf says about the DWARF tags for
that function:
So, the first time in e1000_clean_jumbo_rx_irq() where e1000_consume_page() is
inlined is at PC 0x17be6, which subtracted from e1000_clean_jumbo_rx_irq()'s
address, gives us the offset we should use in the probe definition:
0x17be6 - 0x17a30 = 438
but above we have 876, which is twice as much.
Lets see the second inline expansion of e1000_consume_page() in
e1000_clean_jumbo_rx_irq():
Current DTLB load/store miss events (0x608/0x649) only counts 4K,2M and
4M page size.
Need to extend the events to support any page size (4K/2M/4M/1G).
When using get_options() it's possible to specify a range of numbers,
like 1-100500. The problem is that it doesn't track array size while
calling internally to get_range() which iterates over the range and
fills the memory with numbers.
Link: http://lkml.kernel.org/r/2613C75C-B04D-4BFF-82A6-12F97BA0F620@gmail.com Signed-off-by: Ilya V. Matveychikov <matvejchikov@gmail.com> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dax_writeback_mapping_range() fails to update iteration index when
searching radix tree for entries needing cache flushing. Thus each
pagevec worth of entries is searched starting from the start which is
inefficient and prone to livelocks. Update index properly.
Link: http://lkml.kernel.org/r/20170619124531.21491-1-jack@suse.cz Fixes: 9973c98ecfda3 ("dax: add support for fsync/sync") Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
