As __vringh_iov() traverses a descriptor chain, it populates
each descriptor entry into either read or write vring iov
and increments that iov's ->used member. So, as we iterate
over a descriptor chain, at any point, (riov/wriov)->used
value gives the number of descriptor enteries available,
which are to be read or written by the device. As all read
iovs must precede the write iovs, wiov->used should be zero
when we are traversing a read descriptor. Current code checks
for wiov->i, to figure out whether any previous entry in the
current descriptor chain was a write descriptor. However,
iov->i is only incremented, when these vring iovs are consumed,
at a later point, and remain 0 in __vringh_iov(). So, correct
the check for read and write descriptor order, to use
wiov->used.
Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org> Link: https://lore.kernel.org/r/1624591502-4827-1-git-send-email-neeraju@codeaurora.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Do not call vDPA drivers' callbacks with vq indicies larger than what
the drivers indicate that they support. vDPA drivers do not bounds
check the indices.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Link: https://lore.kernel.org/r/20210701114652.21956-1-vincent.whitchurch@axis.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a virtio pci device undergo surprise removal (aka async removal in
PCIe spec), mark the device as broken so that any upper layer drivers can
abort any outstanding operation.
When a virtio net pci device undergo surprise removal which is used by a
NetworkManager, a below call trace was observed.
Currently vq->broken field is read by virtqueue_is_broken() in busy
loop in one context by virtnet_send_command().
vq->broken is set to true in other process context by
virtio_break_device(). Reader and writer are accessing it without any
synchronization. This may lead to a compiler optimization which may
result to optimize reading vq->broken only once.
Hence, force reading vq->broken on each invocation of
virtqueue_is_broken() and also force writing it so that such
update is visible to the readers.
It is a theoretical fix that isn't yet encountered in the field.
Some products (So) may have two different types of products
with different mac-type that are otherwise equivalent, and
have the same PNVM data, so the PNVM file will contain two
(or perhaps later more) HW-type TLVs. Accept the file and
use the data section that contains any matching entry.
The probe was manually passing NULL instead of dev to devm_clk_hw_register.
This caused a Unable to handle kernel NULL pointer dereference error.
Fix this by passing 'dev'.
Signed-off-by: Adam Ford <aford173@gmail.com> Fixes: a20a40a8bbc2 ("clk: renesas: rcar-usb2-clock-sel: Fix error handling in .probe()") Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
push_rt_task() attempts to move the currently running task away if the
next runnable task has migration disabled and therefore is pinned on the
current CPU.
The current task is retrieved via get_push_task() which only checks for
nr_cpus_allowed == 1, but does not check whether the task has migration
disabled and therefore cannot be moved either. The consequence is a
pointless invocation of the migration thread which correctly observes
that the task cannot be moved.
Return NULL if the task has migration disabled and cannot be moved to
another CPU.
Fixes: a7c81556ec4d3 ("sched: Fix migrate_disable() vs rt/dl balancing") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20210826133738.yiotqbtdaxzjsnfj@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
The u32 variable pci_dword is being masked with 0x1fffffff and then left
shifted 23 places. The shift is a u32 operation,so a value of 0x200 or
more in pci_dword will overflow the u32 and only the bottow 32 bits
are assigned to addr. I don't believe this was the original intent.
Fix this by casting pci_dword to a resource_size_t to ensure no
overflow occurs.
Note that the mask and 12 bit left shift operation does not need this
because the mask SNR_IMC_MMIO_MEM0_MASK and shift is always a 32 bit
value.
Fixes: ee49532b38dd ("perf/x86/intel/uncore: Add IMC uncore support for Snow Ridge")
Addresses-Coverity: ("Unintentional integer overflow") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Reviewed-by: Kan Liang <kan.liang@linux.intel.com> Link: https://lore.kernel.org/r/20210706114553.28249-1-colin.king@canonical.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If the endpoint completion callback is call right after the ep_enabled flag
is cleared and before usb_ep_dequeue() is call, we could do a double free
on the request and the associated buffer.
Fix this by clearing ep_enabled after all the endpoint requests have been
dequeued.
Fixes: b60189e0392f ("net: stmmac: Integrate EST with TAPRIO scheduler API") Cc: <stable@vger.kernel.org> # 5.10.x Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a mutex lock to protect est structure parameters so that the
EST parameters can be updated by other threads.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It turned out that the change from the reverted commit breaks the ACPI
based rpi's because it causes the 100Mhz max clock to be overridden to the
return from sdhci_iproc_get_max_clock(), which is 0 because there isn't a
OF/DT based clock device.
Reported-by: Jeremy Linton <jeremy.linton@arm.com> Fixes: 419dd626e357 ("mmc: sdhci-iproc: Set SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN on BCM2711") Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 71f642833284 ("ACPI: utils: Fix reference counting in
for_each_acpi_dev_match()") moved adev assignment outside of error
path and hence made acpi_dev_put(sensor->adev) a no-op. We still
need to drop reference count on error path, and to achieve that,
replace sensor->adev by locally assigned adev.
Fixes: 71f642833284 ("ACPI: utils: Fix reference counting in for_each_acpi_dev_match()")
Depends-on: fc68f42aa737 ("ACPI: fix NULL pointer dereference") Reported-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, when query PFC configuration by dcbtool, driver will return
PFC enable status based on TC. As all priorities are mapped to TC0 by
default, if TC0 is enabled, then all priorities mapped to TC0 will be
shown as enabled status when query PFC setting, even though some
priorities have never been set.
for example:
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:off 1:off 2:off 3:off 4:off 5:off 6:off 7:off
$ dcb pfc set dev eth0 prio-pfc 0:on 1:on 2:on 3:on
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:on 1:on 2:on 3:on 4:on 5:on 6:on 7:on
To fix this problem, just returns user's PFC config parameter saved in
driver.
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
VLAN list should not be added duplicate VLAN node, otherwise it would
cause "add failed" when restore VLAN from VLAN list, so this patch adds
VLAN ID check before adding node into VLAN list.
In bond 4, when the link goes down and up repeatedly, the bond may get an
unknown speed, and then this port can not work.
The driver notify netif_carrier_on() before update the link state, when the
bond receive carrier on, will query the speed of the port, if the query
operation happens before updating the link state, will get an unknown
speed. So need to notify netif_carrier_on() after update the link state.
After the cmdq registers are cleared, the firmware may take time to
clear out possible left over commands in the cmdq. Driver must release
cmdq memory only after firmware has completed processing of left over
commands.
Fixes: 232d0d55fca6 ("net: hns3: uninitialize command queue while unloading PF driver") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a PF is bonded to a virtual machine and the virtual machine exits
unexpectedly, some hardware resource cannot be cleared. In this case,
loading driver may cause exceptions. Therefore, the hardware resource
needs to be cleared when the driver is loaded.
Currently when device is moved between network namespaces using
RTM_NEWLINK message type and one of netns attributes (FLA_NET_NS_PID,
IFLA_NET_NS_FD, IFLA_TARGET_NETNSID) but w/o specifying IFLA_IFNAME, and
target namespace already has device with same name, userspace will get
EINVAL what is confusing and makes debugging harder.
Fix it so that userspace gets more appropriate EEXIST instead what makes
debugging much easier.
Before:
# ./ifname.sh
+ ip netns add ns0
+ ip netns exec ns0 ip link add l0 type dummy
+ ip netns exec ns0 ip link show l0
8: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 66:90:b5:d5:78:69 brd ff:ff:ff:ff:ff:ff
+ ip link add l0 type dummy
+ ip link show l0
10: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 6e:c6:1f:15:20:8d brd ff:ff:ff:ff:ff:ff
+ ip link set l0 netns ns0
RTNETLINK answers: Invalid argument
After:
# ./ifname.sh
+ ip netns add ns0
+ ip netns exec ns0 ip link add l0 type dummy
+ ip netns exec ns0 ip link show l0
8: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 1e:4a:72:e3:e3:8f brd ff:ff:ff:ff:ff:ff
+ ip link add l0 type dummy
+ ip link show l0
10: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether f2:fc:fe:2b:7d:a6 brd ff:ff:ff:ff:ff:ff
+ ip link set l0 netns ns0
RTNETLINK answers: File exists
The problem is that do_setlink() passes its `char *ifname` argument,
that it gets from a caller, to __dev_change_net_namespace() as is (as
`const char *pat`), but semantics of ifname and pat can be different.
, i.e. do_setlink() gets ifname pointer that is always valid no matter
if user specified IFLA_IFNAME or not and then do_setlink() passes this
ifname pointer as is to __dev_change_net_namespace() as pat argument.
But the pat (pattern) in __dev_change_net_namespace() is used as:
net/core/dev.c
11198 err = -EEXIST;
11199 if (__dev_get_by_name(net, dev->name)) {
11200 /* We get here if we can't use the current device name */
11201 if (!pat)
11202 goto out;
11203 err = dev_get_valid_name(net, dev, pat);
11204 if (err < 0)
11205 goto out;
11206 }
As the result the `goto out` path on line 11202 is neven taken and
instead of returning EEXIST defined on line 11198,
__dev_change_net_namespace() returns an error from dev_get_valid_name()
and this, in turn, will be EINVAL for ifname[0] = '\0' set earlier.
Fixes: d8a5ec672768 ("[NET]: netlink support for moving devices between network namespaces.") Signed-off-by: Andrey Ignatov <rdna@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Traffic schedules can only be started up to eight seconds within the
future. Therefore, the driver periodically checks every two seconds whether the
admin base time provided by the user is inside that window. If so the schedule
is started. Otherwise the check is deferred.
However, according to the programming manual the look ahead window size should
be four - not eight - seconds. By using the proposed value of four seconds
starting a schedule at a specified admin base time actually works as expected.
Fixes: 24dfc6eb39b2 ("net: dsa: hellcreek: Add TAPRIO offloading support") Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the gate control list which is programmed into the hardware is
incorrect resulting in wrong traffic schedules. The problem is the loop
variables are incremented before they are referenced. Therefore, move the
increment to the end of the loop.
Fixes: 24dfc6eb39b2 ("net: dsa: hellcreek: Add TAPRIO offloading support") Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When adapter init fails, the blocked freelist bitmap is already freed
up and should not be touched. So, move the bitmap zeroing closer to
where it was successfully allocated. Also handle adapter init failure
unwind path immediately and avoid setting up RDMA memory windows.
Fixes: 5b377d114f2b ("cxgb4: Add debugfs facility to inject FL starvation") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A group of security researchers brought to our attention
the weakness of hash function used in rt6_exception_hash()
Lets use siphash instead of Jenkins Hash, to considerably
reduce security risks.
Following patch deals with IPv4.
Fixes: 35732d01fe31 ("ipv6: introduce a hash table to store dst cache") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Keyu Man <kman001@ucr.edu> Cc: Wei Wang <weiwan@google.com> Cc: Martin KaFai Lau <kafai@fb.com> Acked-by: Wei Wang <weiwan@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the attempt to reserve a slot fails, we currently leak the XPT_BUSY
flag on the socket. Among other things, this make it impossible to close
the socket.
Fixes: 82011c80b3ec ("SUNRPC: Move svc_xprt_received() call sites") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the change() function decreases the value of 'nstrict', we must take
into account that packets might be already enqueued on a class that flips
from 'strict' to 'quantum': otherwise that class will not be added to the
bandwidth-sharing list. Then, a call to ets_qdisc_reset() will attempt to
do list_del(&alist) with 'alist' filled with zero, hence the NULL pointer
dereference.
For classes flipping from 'strict' to 'quantum', initialize an empty list
and eventually add it to the bandwidth-sharing list, if there are packets
already enqueued. In this way, the kernel will:
a) prevent crashing as described above.
b) avoid retaining the backlog packets (for an arbitrarily long time) in
case no packet is enqueued after a change from 'strict' to 'quantum'.
Reported-by: Hangbin Liu <liuhangbin@gmail.com> Fixes: dcc68b4d8084 ("net: sch_ets: Add a new Qdisc") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to increment the ucounts reference counter befor security_prepare_creds()
because this function may fail and abort_creds() will try to decrement
this reference.
According to Armada XP datasheet bit at 0 position is corresponding for
TxInProg indication.
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network unit") Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A successful 'xge_mdio_config()' call should be balanced by a corresponding
'xge_mdio_remove()' call in the error handling path of the probe, as
already done in the remove function.
Update the error handling path accordingly.
Fixes: ea8ab16ab225 ("drivers: net: xgene-v2: Add MDIO support") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Validate csum_start in gre_handle_offloads before we call _gre_xmit so
that we do not crash later when the csum_start value is used in the
lco_csum function call.
This patch deals with ipv4 code.
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Reported-by: syzbot+ff8e1b9f2f36481e2efc@syzkaller.appspotmail.com Signed-off-by: Shreyansh Chouhan <chouhan.shreyansh630@gmail.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
On new platforms, the NVM is read-only. Attempting to update the NVM
is causing a lockup to occur. Do not attempt to write to the NVM
on platforms where it's not supported.
Emit an error message when the NVM checksum is invalid.
We should decode the latency and the max_latency before directly compare.
The latency should be presented as lat_enc = scale x value:
lat_enc_d = (lat_enc & 0x0x3ff) x (1U << (5*((max_ltr_enc & 0x1c00)
>> 10)))
Fixes: cf8fb73c23aa ("e1000e: add support for LTR on I217/I218") Suggested-by: Yee Li <seven.yi.lee@gmail.com> Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use num_tx_queues rather than the IGC_MAX_TX_QUEUES fixed number 4 when
iterating over tx_ring queue since instantiated queue count could be
less than 4 where on-line cpu count is less than 4.
Fixes: ec50a9d437f0 ("igc: Add support for taprio offloading") Signed-off-by: Toshiki Nishioka <toshiki.nishioka@intel.com> Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Tested-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After unplug thunderbolt dock with i225, pciehp interrupt is triggered,
remove call will read/write mmio address which is already disconnected,
then cause page fault and make system hang.
Fixes: 13b5b7fd6a4a ("igc: Add support for Tx/Rx rings") Fixes: b03c49cde61f ("igc: Save PTP time before a reset") Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
- restore the behavior in enable_net_traffic() to avoid regressions - Jakub
Kicinski;
- hurried up and removed redundant assignment in pegasus_open() before yet
another checker complains;
Fixes: 8a160e2e9aeb ("net: usb: pegasus: Check the return value of get_geristers() and friends;") Reported-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Petko Manolov <petko.manolov@konsulko.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The devlink dev info command reports version information about the
device and firmware running on the board. This includes the "board.id"
field which is supposed to represent an identifier of the board design.
The ice driver uses the Product Board Assembly identifier for this.
In some cases, the PBA is not present in the NVM. If this happens,
devlink dev info will fail with an error. Instead, modify the
ice_info_pba function to just exit without filling in the context
buffer. This will cause the board.id field to be skipped. Log a dev_dbg
message in case someone wants to confirm why board.id is not showing up
for them.
Fixes: e961b679fb0b ("ice: add board identifier info to devlink .info_get") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20210819223451.245613-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
rxe_mcast_add_grp_elem() in rxe_mcast.c calls rxe_alloc() while holding
spinlocks which in turn calls kzalloc(size, GFP_KERNEL) which is
incorrect. This patch replaces rxe_alloc() by rxe_alloc_locked() which
uses GFP_ATOMIC. This bug was caused by the below mentioned commit and
failing to handle the need for the atomic allocate.
Fixes: 4276fd0dddc9 ("RDMA/rxe: Remove RXE_POOL_ATOMIC") Link: https://lore.kernel.org/r/20210813210625.4484-1-rpearsonhpe@gmail.com Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The fixed commit removes all rtnl_lock() and rtnl_unlock() calls in
function bnxt_re_dev_init(), but forgets to remove a rtnl_unlock() in the
error handling path of bnxt_re_register_netdev(), which may cause a
deadlock. This bug is suggested by a static analysis tool.
Fixes: c2b777a95923 ("RDMA/bnxt_re: Refactor device add/remove functionalities") Link: https://lore.kernel.org/r/20210816085531.12167-1-dinghao.liu@zju.edu.cn Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Acked-by: Selvin Xavier <selvin.xavier@broadcom.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
kmalloc_array() is called to allocate memory for tx->descp. If it fails,
the function __sdma_txclean() is called:
__sdma_txclean(dd, tx);
However, in the function __sdma_txclean(), tx-descp is dereferenced if
tx->num_desc is not zero:
sdma_unmap_desc(dd, &tx->descp[0]);
To fix this possible null-pointer dereference, assign the return value of
kmalloc_array() to a local variable descp, and then assign it to tx->descp
if it is not NULL. Otherwise, go to enomem.
Fixes: 7724105686e7 ("IB/hfi1: add driver files") Link: https://lore.kernel.org/r/20210806133029.194964-1-islituo@gmail.com Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Tuo Li <islituo@gmail.com> Tested-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Acked-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the below crash when deleting a slave from the unaffiliated list
twice. First time when the slave is bound to the master and the second
when the slave is unloaded.
Fix it by checking if slave is unaffiliated (doesn't have ib device)
before removing from the list.
blk_mq_run_hw_queues
^^^^^^ dispatch IO, q_usage_counter will reduce to zero
blk_mq_unfreeze_queue
^^^^^ mq_freeze_depth--
To fix this, we need to run queue before rescanning device when the device
state changes to SDEV_RUNNING.
Link: https://lore.kernel.org/r/20210824025921.3277629-1-lijinlin3@huawei.com Fixes: f0f82e2476f6 ("scsi: core: Fix capacity set to zero after offlinining device") Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Li Jinlin <lijinlin3@huawei.com> Signed-off-by: Qiu Laibin <qiulaibin@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a USB cable disconnect, or soft disconnect scenario, a pending
SETUP transaction may not be completed, leading to the following
error:
dwc3 a600000.dwc3: timed out waiting for SETUP phase
If this occurs, then the entire pullup disable routine is skipped and
proper cleanup and halting of the controller does not complete.
Instead of returning an error (which is ignored from the UDC
perspective), allow the pullup disable routine to continue, which
will also handle disabling of EP0/1. This will end any active
transfers as well. Ensure to clear any delayed_status also, as the
timeout could happen within the STATUS stage.
Fixes: bb0147364850 ("usb: dwc3: gadget: don't clear RUN/STOP when it's invalid to do so") Cc: <stable@vger.kernel.org> Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Acked-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Wesley Cheng <wcheng@codeaurora.org> Link: https://lore.kernel.org/r/20210825042855.7977-1-wcheng@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't depend on the TRB's HWO bit to determine if the TRB ring is
"full". A TRB is only available when the driver had processed it, not
when the controller consumed and relinquished the TRB's ownership to the
driver. Otherwise, the driver may overwrite unprocessed TRBs. This can
happen when many transfer events accumulate and the system is slow to
process them and/or when there are too many small requests.
If a request is in the started_list, that means there is one or more
unprocessed TRBs remained. Check this instead of the TRB's HWO bit
whether the TRB ring is full.
If the port is going to send Discover_Identity Message, vdm_sm_running
flag was intentionally set before entering Ready States in order to
avoid the conflict because the port and the port partner might start
AMS at almost the same time after entering Ready States.
However, the original design has a problem. When the port is doing
DR_SWAP from Device to Host, it raises the flag. Later in the
tcpm_send_discover_work, the flag blocks the procedure of sending the
Discover_Identity and it might never be cleared until disconnection.
Since there exists another flag send_discover representing that the port
is going to send Discover_Identity or not, it is enough to use that flag
to prevent the conflict. Also change the timing of the set/clear of
vdm_sm_running to indicate whether the VDM SM is actually running or
not.
The recent attempt to handle an unknown ROM state in the commit d143825baf15 ("usb: renesas-xhci: Fix handling of unknown ROM state")
resulted in a regression and reverted later by the commit 44cf53602f5a
("Revert "usb: renesas-xhci: Fix handling of unknown ROM state"").
The problem of the former fix was that it treated the failure of
firmware loading as a fatal error. Since the firmware files aren't
included in the standard linux-firmware tree, most users don't have
them, hence they got the non-working system after that. The revert
fixed the regression, but also it didn't make the firmware loading
triggered even on the devices that do need it. So we need still a fix
for them.
This is another attempt to handle the unknown ROM state. Like the
previous fix, this also tries to load the firmware when ROM shows
unknown state. In this patch, however, the failure of a firmware
loading (such as a missing firmware file) isn't handled as a fatal
error any longer when ROM has been already detected, but it falls back
to the ROM mode like before. The error is returned only when no ROM
is detected and the firmware loading failed.
Along with it, for simplifying the code flow, the detection and the
check of ROM is factored out from renesas_fw_check_running() and done
in the caller side, renesas_xhci_check_request_fw(). It avoids the
redundant ROM checks.
The patch was tested on Lenovo Thinkpad T14 gen (BIOS 1.34). Also it
was confirmed that no regression is seen on another Thinkpad T14
machine that has worked without the patch, too.
These devices do not appear to send a zero-length packet when the
transfer size is a multiple of the bulk-endpoint max-packet size. This
means that incoming data may not be processed by the driver until a
short packet is received or the receive buffer is full.
Revert back to using endpoint-sized receive buffers to avoid stalled
reads.
schedule_delayed_work does not push back the work if it was already
scheduled before, so amdgpu_device_delay_enable_gfx_off ran ~100 ms
after the first time GFXOFF was disabled and re-enabled, even if GFXOFF
was disabled and re-enabled again during those 100 ms.
This resulted in frame drops / stutter with the upcoming mutter 41
release on Navi 14, due to constantly enabling GFXOFF in the HW and
disabling it again (for getting the GPU clock counter).
To fix this, call cancel_delayed_work_sync when the disable count
transitions from 0 to 1, and only schedule the delayed work on the
reverse transition, not if the disable count was already 0. This makes
sure the delayed work doesn't run at unexpected times, and allows it to
be lock-free.
v2:
* Use cancel_delayed_work_sync & mutex_trylock instead of
mod_delayed_work.
v3:
* Make amdgpu_device_delay_enable_gfx_off lock-free (Christian König)
v4:
* Fix race condition between amdgpu_gfx_off_ctrl incrementing
adev->gfx.gfx_off_req_count and amdgpu_device_delay_enable_gfx_off
checking for it to be 0 (Evan Quan)
Cc: stable@vger.kernel.org Reviewed-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> # v3 Acked-by: Christian König <christian.koenig@amd.com> # v3 Signed-off-by: Michel Dänzer <mdaenzer@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm_dp_dpcd_read/write already has debug error message.
Drop redundant error messages which gives false
status even if correct value is read in drm_dp_dpcd_read().
v2: -Added fixes tag (Ankit)
v3: -Fixed build error (CI)
Fixes: 9488a030ac91 ("drm/i915: Add support for enabling link status and recovery") Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Sean Paul <seanpaul@chromium.org> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: <stable@vger.kernel.org> # v5.12+ Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Swati Sharma <swati2.sharma@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210812131107.5531-1-swati2.sharma@intel.com
(cherry picked from commit b6dfa416172939edaa46a5a647457b94c6d94119) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A small race exists between intel_gt_retire_requests_timeout and
intel_timeline_exit which could result in the syncmap not getting
free'd. Rather than work to hard to seal this race, simply cleanup the
syncmap on fini.
After free xsk_pool, there is possibility that napi polling is still
running in the middle, thus causes a kernel crash due to kernel NULL
pointer dereference of rx_q->xsk_pool and tx_q->xsk_pool.
Fix this by changing the XDP pool setup sequence to:
1. disable napi before free xsk_pool
2. enable napi after init xsk_pool
The following kernel panic is observed without this patch:
[BUG]
It's no longer possible to create compressed inline extent after commit f2165627319f ("btrfs: compression: don't try to compress if we don't
have enough pages").
[CAUSE]
For compression code, there are several possible reasons we have a range
that needs to be compressed while it's no more than one page.
- Compressed inline write
The data is always smaller than one sector and the test lacks the
condition to properly recognize a non-inline extent.
- Compressed subpage write
For the incoming subpage compressed write support, we require page
alignment of the delalloc range.
And for 64K page size, we can compress just one page into smaller
sectors.
For those reasons, the requirement for the data to be more than one page
is not correct, and is already causing regression for compressed inline
data writeback. The idea of skipping one page to avoid wasting CPU time
could be revisited in the future.
[FIX]
Fix it by reverting the offending commit.
Reported-by: Zygo Blaxell <ce3g8jdj@umail.furryterror.org> Link: https://lore.kernel.org/linux-btrfs/afa2742.c084f5d6.17b6b08dffc@tnonline.net Fixes: f2165627319f ("btrfs: compression: don't try to compress if we don't have enough pages") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If offline_pages failed after lru_cache_disable(), it forgot to do
lru_cache_enable() in error path. So we would have lru cache disabled
permanently in this case.
Link: https://lkml.kernel.org/r/20210821094246.10149-3-linmiaohe@huawei.com Fixes: d479960e44f2 ("mm: disable LRU pagevec during the migration temporarily") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Reviewed-by: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Chris Goldsworthy <cgoldswo@codeaurora.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Minchan Kim <minchan@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 66f24fa766e3 ("mm: drop redundant ARCH_ENABLE_SPLIT_PMD_PTLOCK")
broke PMD split page table lock for powerpc.
It selects the non-existent config ARCH_ENABLE_PMD_SPLIT_PTLOCK in
arch/powerpc/platforms/Kconfig.cputype, but clearly intended to
select ARCH_ENABLE_SPLIT_PMD_PTLOCK (notice the word swapping!), as
that commit did for all other architectures.
Fix it by selecting the correct symbol ARCH_ENABLE_SPLIT_PMD_PTLOCK.
Fixes: 66f24fa766e3 ("mm: drop redundant ARCH_ENABLE_SPLIT_PMD_PTLOCK") Cc: stable@vger.kernel.org # v5.13+ Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Reviewed-by: Daniel Axtens <dja@axtens.net>
[mpe: Reword change log to make it clear this is a bug fix] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210819113954.17515-3-lukas.bulwahn@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value of FP registers in the core dump file comes from the
thread.fstate. However, kernel saves the FP registers to the thread.fstate
only before scheduling out the process. If no process switch happens
during the exception handling process, kernel will not have a chance to
save the latest value of FP registers to thread.fstate. It will cause the
value of FP registers in the core dump file may be incorrect. To solve this
problem, this patch force lets kernel save the FP register into the
thread.fstate if the target task_struct equals the current.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com> Reviewed-by: Jisheng Zhang <jszhang@kernel.org> Fixes: b8c8a9590e4f ("RISC-V: Add FP register ptrace support for gdb.") Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the schema fixups are applied to 'select' the result is a single
entry is required for a match, but that will never match as there should
be 2 entries. Also, a 'select' schema should have the widest possible
match, so use 'contains' which matches the compatible string(s) in any
position and not just the first position.
The ceph_cap_flush structures are usually dynamically allocated, but
the ceph_cap_snap has an embedded one.
When force umounting, the client will try to remove all the session
caps. During this, it will free them, but that should not be done
with the ones embedded in a capsnap.
Fix this by adding a new boolean that indicates that the cap flush is
embedded in a capsnap, and skip freeing it if that's set.
At the same time, switch to using list_del_init() when detaching the
i_list and g_list heads. It's possible for a forced umount to remove
these objects but then handle_cap_flushsnap_ack() races in and does the
list_del_init() again, corrupting memory.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/52283 Signed-off-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the interchanged fetch of the CAN RX and TX error
counters from the ESD_EV_CAN_ERROR_EXT message. The RX error counter
is really in struct rx_msg::data[2] and the TX error counter is in
struct rx_msg::data[3].
Fixes: 96d8e90382dc ("can: Add driver for esd CAN-USB/2 device") Link: https://lore.kernel.org/r/20210825215227.4947-2-stefan.maetje@esd.eu Cc: stable@vger.kernel.org Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ocelot driver makes use of regmap, wrapping it with driver specific
operations that are thin wrappers around the core regmap APIs. These are
exported with EXPORT_SYMBOL, dropping the _GPL from the core regmap
exports which is frowned upon. Add _GPL suffixes to at least the APIs that
are doing register I/O.
Signed-off-by: Mark Brown <broonie@kernel.org> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
One error path can result in release_dentry_name_snapshot() being called
before "name" was initialized by take_dentry_name_snapshot().
Fix by moving the release_dentry_name_snapshot() to immediately after the
only use.
Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
where it's clear we end up calling the percpu count release directly
from the completion path, as it's in atomic mode and we drop the last
ref. For file/block IO, this can be from IRQ context already, and the
softirq locking for rsrc isn't enough.
Just make the lock fully IRQ safe, and ensure we correctly safe state
from the release path as we don't know the full context there.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: David S. Miller <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Reported-by: Minmin chen <chenmingmin@huawei.com> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Michal Kubecek reports that conntrack gc is responsible for frequent
wakeups (every 125ms) on idle systems.
On busy systems, timed out entries are evicted during lookup.
The gc worker is only needed to remove entries after system becomes idle
after a busy period.
To resolve this, always scan the entire table.
If the scan is taking too long, reschedule so other work_structs can run
and resume from next bucket.
After a completed scan, wait for 2 minutes before the next cycle.
Heuristics for faster re-schedule are removed.
GC_SCAN_INTERVAL could be exposed as a sysctl in the future to allow
tuning this as-needed or even turn the gc worker off.
Reported-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The range size of consecutive elements were not limited. Thus one could
define a huge range which may result soft lockup errors due to the long
execution time. Now the range size is limited to 2^20 entries.
Various 360 degree hinges (yoga) style 2-in-1 devices use 2 accelerometers
to allow the OS to determine the angle between the display and the base of
the device.
On Windows these are read by a special HingeAngleService process which
calls undocumented ACPI methods, to let the firmware know if the 2-in-1 is
in tablet- or laptop-mode. The firmware may use this to disable the kbd and
touchpad to avoid spurious input in tablet-mode as well as to report
SW_TABLET_MODE info to the OS.
Since Linux does not call these undocumented methods, the SW_TABLET_MODE
info reported by various pdx86 drivers is incorrect on these devices.
Before this commit the intel-hid and thinkpad_acpi code already had 2
hardcoded checks for ACPI hardware-ids of dual-accel sensors to avoid
reporting broken info.
And now we also have a bug-report about the same problem in the intel-vbtn
code. Since there are at least 3 different ACPI hardware-ids in play, add
a new dual_accel_detect() helper which checks for all 3, rather then
adding different hardware-ids to the drivers as bug-reports trickle in.
Having shared code which checks all known hardware-ids is esp. important
for the intel-hid and intel-vbtn drivers as these are generic drivers
which are used on a lot of devices.
The BOSC0200 hardware-id requires special handling, because often it is
used for a single-accelerometer setup. Only in a few cases it refers to
a dual-accel setup, in which case there will be 2 I2cSerialBus resources
in the device's resource-list, so the helper checks for this.
When the component level pin control functions were added they for some
no longer obvious reason handled adding prefixing of widget names. This
meant that when the lack of prefix handling in the DAPM level pin
operations was fixed by ae4fc532244b3bb4d (ASoC: dapm: use component
prefix when checking widget names) the one device using the component
level API ended up with the prefix being applied twice, causing all
lookups to fail.
Fix this by removing the redundant prefixing from the component code,
which has the nice side effect of also making that code much simpler.
Reported-by: Richard Fitzgerald <rf@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Tested-by: Lucas Tanure <tanureal@opensource.cirrus.com> Link: https://lore.kernel.org/r/20210726194123.54585-1-broonie@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 457f44363a88 ("bpf: Implement BPF ring buffer and verifier support
for it") extended check_map_func_compatibility() by enforcing map -> helper
function match, but not helper -> map type match.
Due to this all of the bpf_ringbuf_*() helper functions could be used with
a wrong map type such as array or hash map, leading to invalid access due
to type confusion.
Also, both BPF_FUNC_ringbuf_{submit,discard} have ARG_PTR_TO_ALLOC_MEM as
argument and not a BPF map. Therefore, their check_map_func_compatibility()
presence is incorrect since it's only for map type checking.
Fixes: 457f44363a88 ("bpf: Implement BPF ring buffer and verifier support for it") Reported-by: Ryota Shiga (Flatt Security) Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've had CONFIG_MANDATORY_FILE_LOCKING since 2015 and a lot of distros
have disabled it. Warn the stragglers that still use "-o mand" that
we'll be dropping support for that mount option.
Cc: stable@vger.kernel.org Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We currently check for ret != 0 to indicate error, but '1' is a valid
return and just indicates that the allocation succeeded with a wrap.
Correct the check to be for < 0, like it was before the xarray
conversion.
syzbot hit kernel BUG at fs/hugetlbfs/inode.c:532 as described in [1].
This BUG triggers if the HPageRestoreReserve flag is set on a page in
the page cache. It should never be set, as the routine
huge_add_to_page_cache explicitly clears the flag after adding a page to
the cache.
The only code other than huge page allocation which sets the flag is
restore_reserve_on_error. It will potentially set the flag in rare out
of memory conditions. syzbot was injecting errors to cause memory
allocation errors which exercised this specific path.
The code in restore_reserve_on_error is doing the right thing. However,
there are instances where pages in the page cache were being passed to
restore_reserve_on_error. This is incorrect, as once a page goes into
the cache reservation information will not be modified for the page
until it is removed from the cache. Error paths do not remove pages
from the cache, so even in the case of error, the page will remain in
the cache and no reservation adjustment is needed.
Modify routines that potentially call restore_reserve_on_error with a
page cache page to no longer do so.
Note on fixes tag: Prior to commit 846be08578ed ("mm/hugetlb: expand
restore_reserve_on_error functionality") the routine would not process
page cache pages because the HPageRestoreReserve flag is not set on such
pages. Therefore, this issue could not be trigggered. The code added
by commit 846be08578ed ("mm/hugetlb: expand restore_reserve_on_error
functionality") is needed and correct. It exposed incorrect calls to
restore_reserve_on_error which is the root cause addressed by this
commit.
Originally the addr != NULL check was meant to take care of the case
where __kfence_pool == NULL (KFENCE is disabled). However, this does
not work for addresses where addr > 0 && addr < KFENCE_POOL_SIZE.
This can be the case on NULL-deref where addr > 0 && addr < PAGE_SIZE or
any other faulting access with addr < KFENCE_POOL_SIZE. While the
kernel would likely crash, the stack traces and report might be
confusing due to double faults upon KFENCE's attempt to unprotect such
an address.
Fix it by just checking that __kfence_pool != NULL instead.
Link: https://lkml.kernel.org/r/20210818130300.2482437-1-elver@google.com Fixes: 0ce20dd84089 ("mm: add Kernel Electric-Fence infrastructure") Signed-off-by: Marco Elver <elver@google.com> Reported-by: Kuan-Ying Lee <Kuan-Ying.Lee@mediatek.com> Acked-by: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: <stable@vger.kernel.org> [5.12+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
HWPoisonHandlable() sometimes returns false for typical user pages due
to races with average memory events like transfers over LRU lists. This
causes failures in hwpoison handling.
There's retry code for such a case but does not work because the retry
loop reaches the retry limit too quickly before the page settles down to
handlable state. Let get_any_page() call shake_page() to fix it.
[naoya.horiguchi@nec.com: get_any_page(): return -EIO when retry limit reached] Link: https://lkml.kernel.org/r/20210819001958.2365157-1-naoya.horiguchi@linux.dev Link: https://lkml.kernel.org/r/20210817053703.2267588-1-naoya.horiguchi@linux.dev Fixes: 25182f05ffed ("mm,hwpoison: fix race with hugetlb page allocation") Signed-off-by: Naoya Horiguchi <naoya.horiguchi@nec.com> Reported-by: Tony Luck <tony.luck@intel.com> Reviewed-by: Yang Shi <shy828301@gmail.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> [5.13+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
__get_hwpoison_page() could fail to grab refcount by some race condition,
so it's helpful if we can handle it by retrying. We already have retry
logic, so make get_hwpoison_page() call get_any_page() when called from
memory_failure().
As a result, get_hwpoison_page() can return negative values (i.e. error
code), so some callers are also changed to handle error cases.
soft_offline_page() does nothing for -EBUSY because that's enough and
users in userspace can easily handle it. unpoison_memory() is also
unchanged because it's broken and need thorough fixes (will be done
later).
Link: https://lkml.kernel.org/r/20210603233632.2964832-3-nao.horiguchi@gmail.com Signed-off-by: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Tony Luck <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We've noticed occasional OOM killing when memory.low settings are in
effect for cgroups. This is unexpected and undesirable as memory.low is
supposed to express non-OOMing memory priorities between cgroups.
The reason for this is proportional memory.low reclaim. When cgroups
are below their memory.low threshold, reclaim passes them over in the
first round, and then retries if it couldn't find pages anywhere else.
But when cgroups are slightly above their memory.low setting, page scan
force is scaled down and diminished in proportion to the overage, to the
point where it can cause reclaim to fail as well - only in that case we
currently don't retry, and instead trigger OOM.
To fix this, hook proportional reclaim into the same retry logic we have
in place for when cgroups are skipped entirely. This way if reclaim
fails and some cgroups were scanned with diminished pressure, we'll try
another full-force cycle before giving up and OOMing.
[akpm@linux-foundation.org: coding-style fixes]
Link: https://lkml.kernel.org/r/20210817180506.220056-1-hannes@cmpxchg.org Fixes: 9783aa9917f8 ("mm, memcg: proportional memory.{low,min} reclaim") Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reported-by: Leon Yang <lnyng@fb.com> Reviewed-by: Rik van Riel <riel@surriel.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Roman Gushchin <guro@fb.com> Acked-by: Chris Down <chris@chrisdown.name> Acked-by: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> [5.4+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function init_resources() allocates a boot memory block to hold an array of
resources which it adds to iomem_resource. The array is filled in from its
end and the function then attempts to free any unused memory at the
beginning. The problem is that size of the unused memory is incorrectly
calculated and this can result in releasing memory which is in use by
active resources. Their data then gets corrupted later when the memory is
reused by a different part of the system.
Fix the size of the released memory to correctly match the number of unused
resource entries.
Fixes: ffe0e5261268 ("RISC-V: Improve init_resources()") Signed-off-by: Petr Pavlu <petr.pavlu@suse.com> Reviewed-by: Sunil V L <sunilvl@ventanamicro.com> Acked-by: Nick Kossifidis <mick@ics.forth.gr> Tested-by: Sunil V L <sunilvl@ventanamicro.com> Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 2e6b836312a4 ("ASoC: intel: atom: Fix reference to PCM
buffer address") changed the reference of PCM buffer address to
substream->runtime->dma_addr as the buffer address may change
dynamically. However, I forgot that the dma_addr field is still not
set up for the CONTINUOUS buffer type (that this driver uses) yet in
5.14 and earlier kernels, and it resulted in garbage I/O. The problem
will be fixed in 5.15, but we need to address it quickly for now.
The fix is to deduce the address again from the DMA pointer with
virt_to_phys(), but from the right one, substream->runtime->dma_area.
The Renoir XHCI controller apparently doesn't resume reliably with the
standard D3hot-to-D0 delay. Increase it to 20ms.
[Alex: I talked to the AMD USB hardware team and the AMD Windows team and
they are not aware of any HW errata or specific issues. The HW works fine
in Windows. I was told Windows uses a rather generous default delay of
100ms for PCI state transitions.]
Link: https://lore.kernel.org/r/20210722025858.220064-1-alexander.deucher@amd.com Signed-off-by: Marcin Bachry <hegel666@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Prike Liang <prike.liang@amd.com> Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit b5efec00b671 ("powerpc/32s: Move KUEP locking/unlocking in C")
removed the 'isync' instruction after adding/removing NX bit in user
segments. The reasoning behind this change was that when setting the
NX bit we don't mind it taking effect with delay as the kernel never
executes text from userspace, and when clearing the NX bit this is
to return to userspace and then the 'rfi' should synchronise the
context.
However, it looks like on book3s/32 having a hash page table, at least
on the G3 processor, we get an unexpected fault from userspace, then
this is followed by something wrong in the verification of MSR_PR
at end of another interrupt.
This is fixed by adding back the removed isync() following update
of NX bit in user segment registers. Only do it for cores with an
hash table, as 603 cores don't exhibit that problem and the two isync
increase ./null_syscall selftest by 6 cycles on an MPC 832x.
First problem: unexpected WARN_ON() for mysterious PROTFAULT
KUEP implements the update of user segment registers.
Move it into mmu-hash.h in order to use it from other places.
And inline kuep_lock() and kuep_unlock(). Inlining kuep_lock() is
important for system_call_exception(), otherwise system_call_exception()
has to save into stack the system call parameters that are used just
after, and doing that takes more instructions than kuep_lock() itself.
Commit a20dcf53ea98 ("usb: typec: tcpm: Respond Not_Supported if no
snk_vdo"), stops tcpm_pd_data_request() calling tcpm_handle_vdm_request()
when port->nr_snk_vdo is not set. But the VDM might be intended for an
altmode-driver, in which case nr_snk_vdo does not matter.
This change breaks the forwarding of connector hotplug (HPD) events
for displayport altmode on devices which don't set nr_snk_vdo.
tcpm_pd_data_request() is the only caller of tcpm_handle_vdm_request(),
so we can move the nr_snk_vdo check to inside it, at which point we
have already looked up the altmode device so we can check for this too.
Doing this check here also ensures that vdm_state gets set to
VDM_STATE_DONE if it was VDM_STATE_BUSY, even if we end up with
responding with PD_MSG_CTRL_NOT_SUPP later.
Note that tcpm_handle_vdm_request() was already sending
PD_MSG_CTRL_NOT_SUPP in some circumstances, after moving the nr_snk_vdo
check the same error-path is now taken when that check fails. So that
we have only one error-path for this and not two. Replace the
tcpm_queue_message(PD_MSG_CTRL_NOT_SUPP) used by the existing error-path
with the more robust tcpm_pd_handle_msg() from the (now removed) second
error-path.
Fixes: a20dcf53ea98 ("usb: typec: tcpm: Respond Not_Supported if no snk_vdo") Cc: stable <stable@vger.kernel.org> Cc: Kyle Tso <kyletso@google.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: Kyle Tso <kyletso@google.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210816154632.381968-1-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The struct pci_dev uses reference counting but zPCI assumed erroneously
that the last reference would always be the local reference after
calling pci_stop_and_remove_bus_device(). This is usually the case but
not how reference counting works and thus inherently fragile.
In fact one case where this causes a NULL pointer dereference when on an
SRIOV device the function 0 was hot unplugged before another function of
the same multi-function device. In this case the second function's
pdev->sriov->dev reference keeps the struct pci_dev of function 0 alive
even after the unplug. This bug was previously hidden by the fact that
we were leaking the struct pci_dev which in turn means that it always
outlived the struct zpci_dev. This was fixed in commit 0b13525c20fe
("s390/pci: fix leak of PCI device structure") exposing the broken
behavior.
Fix this by accounting for the long living reference a struct pci_dev
has to its underlying struct zpci_dev via the zbus->function[] array and
only release that in pcibios_release_device() ensuring that the struct
pci_dev is not left with a dangling reference. This is a minimal fix in
the future it would probably better to use fine grained reference
counting for struct zpci_dev.
projects / thirdparty / kernel / stable.git / log
