fsl_booke and 44x are not able to map kernel linear memory with
pages, so they can't support DEBUG_PAGEALLOC and KFENCE, and
STRICT_KERNEL_RWX is also a problem for now.
Enable those only on book3s (both 32 and 64 except KFENCE), 8xx and 40x.
Fixes: 88df6e90fa97 ("[POWERPC] DEBUG_PAGEALLOC for 32-bit") Fixes: 95902e6c8864 ("powerpc/mm: Implement STRICT_KERNEL_RWX on PPC32") Fixes: 90cbac0e995d ("powerpc: Enable KFENCE for PPC32") Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/d1ad9fdd9b27da3fdfa16510bb542ed51fa6e134.1634292136.git.christophe.leroy@csgroup.eu Signed-off-by: Sasha Levin <sashal@kernel.org>
If role is changed without the "none" step, A- and B- valid session could
be set at the same time. It is an issue.
This patch resets A-session if role switch sets B-session, and resets
B-session if role switch sets A-session.
Then, it is possible to change the role without the "none" step.
In case of USB_DR_MODE_PERIPHERAL, the OTG clock is disabled at the end of
the probe (it is not the case if USB_DR_MODE_HOST or USB_DR_MODE_OTG).
The clock is then enabled on udc_start.
If dwc2_drd_role_sw_set is called before udc_start (it is the case if the
usb cable is plugged at boot), GOTGCTL and GUSBCFG registers cannot be
read/written, so session cannot be overridden.
To avoid this case, check the ll_hw_enabled value and enable the clock if
it is available, and disable it after the override.
Instead of forcing the role to Device, check the dr_mode configuration.
If the core is Host only, force the mode to Host, this to avoid the
dwc2_force_mode warning:
WARNING: CPU: 1 PID: 21 at drivers/usb/dwc2/core.c:615 dwc2_drd_init+0x104/0x17c
When forcing mode to Host, dwc2_force_mode may sleep the time the host
role is applied. To avoid sleeping while atomic context, move the call
to dwc2_force_mode after spin_unlock_irqrestore. It is safe, as
interrupts are not yet unmasked here.
If the device used as a serial console gets detached/attached at runtime,
register_console() will try to call imx_uart_setup_console(), but this
is not possible since it is marked as __init.
For instance
# cat /sys/devices/virtual/tty/console/active
tty1 ttymxc0
# echo -n N > /sys/devices/virtual/tty/console/subsystem/ttymxc0/console
# echo -n Y > /sys/devices/virtual/tty/console/subsystem/ttymxc0/console
A prior patch introduced HBA_NEEDS_CFG_PORT flag logic, but in
lpfc_sli_brdrestart_s3() code path, right after HBA_NEEDS_CFG_PORT is set,
the phba->hba_flag is cleared in lpfc_sli_brdreset().
Fix by calling lpfc_sli_chipset_init() to wait for successful restart of
the HBA in lpfc_host_reset_handler() after lpfc_sli_brdrestart().
lpfc_sli_chipset_init() sets the HBA_NEEDS_CFG_PORT flag so that the
lpfc_sli_hba_setup() routine from lpfc_online() will execute
lpfc_sli_config_port() initialization step when the brdrestart is
successful.
Link: https://lore.kernel.org/r/20211020211417.88754-3-jsmart2021@gmail.com Fixes: d2f2547efd39 ("scsi: lpfc: Fix auto sli_mode and its effect on CONFIG_PORT for SLI3") Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
UFS drivers that probe defer will end up leaking memory allocated for clk
and regulator names via kstrdup() because the structure that is holding
this memory is allocated via devm_* variants which will be freed during
probe defer but the names are never freed.
Use same devm_* variant of kstrdup to free the memory allocated to name
when driver probe defers.
Kmemleak found around 11 leaks on Qualcomm Dragon Board RB5:
With commit ecb010d441088 ("iio: imu: adis: Refactor adis_initial_startup")
we are doing a HW or SW reset to the device which means that we'll get
the default state of the data ready pin (which is enabled). Hence there's
no point in disabling the IRQ in the init function. Moreover, this
function is intended to initialize internal data structures and not
really do anything on the device.
As a result of this, some devices were left with the data ready pin enabled
after probe which was not the desired behavior. Thus, we move the call to
'adis_enable_irq()' to the initial startup function where it makes more
sense for it to be.
Note that for devices that cannot mask/unmask the pin, it makes no sense
to call the function at this point since the IRQ should not have been
yet requested. This will be improved in a follow up change.
When __iio_buffer_alloc_sysfs_and_mask() failed, 'unwind_idx' should be
set to 'i - 1' to prevent double-free when cleanup resources.
BUG: KASAN: double-free or invalid-free in __iio_buffer_free_sysfs_and_mask+0x32/0xb0 [industrialio]
Call Trace:
kfree+0x117/0x4c0
__iio_buffer_free_sysfs_and_mask+0x32/0xb0 [industrialio]
iio_buffers_alloc_sysfs_and_mask+0x60d/0x1570 [industrialio]
__iio_device_register+0x483/0x1a30 [industrialio]
ina2xx_probe+0x625/0x980 [ina2xx_adc]
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: ee708e6baacd ("iio: buffer: introduce support for attaching more IIO buffers") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20211013094923.2473-2-andriy.shevchenko@linux.intel.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The general expectation is that powering on a power-domain should make
the power domain deliver some power, and if a specific performance state
is needed further requests has to be made.
But in contrast with other power-domain implementations (e.g. rpmpd) the
RPMh does not have an interface to enable the power, so the driver has
to vote for a particular corner (performance level) in rpmh_power_on().
But the corner is never initialized, so a typical request to simply
enable the power domain would not actually turn on the hardware. Further
more, when no more clients vote for a performance state (i.e. the
aggregated vote is 0) the power domain would be turned off.
Fix both of these issues by always voting for a corner with non-zero
value, when the power domain is enabled.
The tracking of the lowest non-zero corner is performed to handle the
corner case if there's ever a domain with a non-zero lowest corner, in
which case both rpmh_power_on() and rpmh_rpmhpd_set_performance_state()
would be allowed to use this lowest corner.
The driver can run without an interrupt so if devm_request_threaded_irq()
failed, the probe() just carried on. But if this was EPROBE_DEFER the
driver would continue without an interrupt instead of deferring to wait
for the interrupt to become available.
Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec") Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Link: https://lore.kernel.org/r/20211015133619.4698-6-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some registers had wrong default values in cs42l42_reg_defaults[].
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec") Link: https://lore.kernel.org/r/20211015133619.4698-4-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
An I2S frame always has two slots (left and right) even when sending
mono. The right channel (channel 2) of ASP TX will always have the
same bit width as the left channel and will always be on the high
phase of LRCLK.
The previous implementation always passed the field masks for both
channels to snd_soc_component_update_bits() but for mono the written value
only contained the settings for channel 1. The result was that for mono
channel 2 was set to 8-bit (which is an invalid configuration) with both
channels on the low phase of LRCLK.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Fixes: 585e7079de0e ("ASoC: cs42l42: Add Capture Support") Link: https://lore.kernel.org/r/20211015133619.4698-3-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The STM32 SAI subblocks registers offsets are in the range
0x0004 (SAIx_CR1) to 0x0020 (SAIx_DR).
The corresponding range length is 0x20 instead of 0x1c.
Change reg property accordingly.
Fixes: 5afd65c3a060 ("ARM: dts: stm32: add sai support on stm32mp157c") Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The SPI NOR is a bit further away from the SoC on DHCOR than on DHCOM,
which causes additional signal delay. At 108 MHz, this delay triggers
a sporadic issue where the first bit of RX data is not received by the
QSPI controller.
There are two options of addressing this problem, either by using the
DLYB block to compensate the extra delay, or by reducing the QSPI bus
clock frequency. The former requires calibration and that is overly
complex, so opt for the second option.
Fixes: 76045bc457104 ("ARM: dts: stm32: Add QSPI NOR on AV96") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On power9 and earlier platforms, the default event used for cyles and
instructions is PM_CYC (0x0001e) and PM_INST_CMPL (0x00002)
respectively. These events use two programmable PMCs and by default will
count irrespective of the run latch state (idle state). But since they
use programmable PMCs, these events can lead to multiplexing with other
events, because there are only 4 programmable PMCs. Hence in power10,
performance monitoring unit (PMU) driver uses performance monitor
counter 5 (PMC5) and performance monitor counter6 (PMC6) for counting
instructions and cycles.
Currently on power10, the event used for cycles is PM_RUN_CYC (0x600F4)
and instructions uses PM_RUN_INST_CMPL (0x500fa). But counting of these
events in idle state is controlled by the CC56RUN bit setting in Monitor
Mode Control Register0 (MMCR0). If the CC56RUN bit is zero, PMC5/6 will
not count when CTRL[RUN] (run latch) is zero. This could lead to missing
some counts if a thread is in idle state during system wide profiling.
To fix it, set the CC56RUN bit in MMCR0 for power10, which makes PMC5
and PMC6 count instructions and cycles regardless of the run latch
state. Since this change make PMC5/6 count as PM_INST_CMPL/PM_CYC,
rename the event code 0x600f4 as PM_CYC instead of PM_RUN_CYC and event
code 0x500fa as PM_INST_CMPL instead of PM_RUN_INST_CMPL. The changes
are only for PMC5/6 event codes and will not affect the behaviour of
PM_RUN_CYC/PM_RUN_INST_CMPL if progammed in other PMC's.
Right now dyndbg shows up as an unknown parameter if used on boot:
Unknown command line parameters: dyndbg=+p
That's because it is unknown, it doesn't sit in the __param
section, so the processing done to warn users supplying an unknown
parameter doesn't think it is legitimate.
Install a dummy handler to register it. dynamic debug needs to search
the whole command line for modules listed that are currently builtin,
so there's no real work to be done in this callback.
Fixes: 86d1919a4fb0 ("init: print out unknown kernel parameters") Tested-by: Jim Cromie <jim.cromie@gmail.com> Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Signed-off-by: Jason Baron <jbaron@akamai.com> Link: https://lore.kernel.org/r/1634139622-20667-2-git-send-email-jbaron@akamai.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
ld: drivers/staging/ks7010/ks_hostif.o: in function `michael_mic.constprop.0':
ks_hostif.c:(.text+0x95b): undefined reference to `crypto_alloc_shash'
ld: ks_hostif.c:(.text+0x97a): undefined reference to `crypto_shash_setkey'
ld: ks_hostif.c:(.text+0xa13): undefined reference to `crypto_shash_update'
ld: ks_hostif.c:(.text+0xa28): undefined reference to `crypto_shash_update'
ld: ks_hostif.c:(.text+0xa48): undefined reference to `crypto_shash_finup'
ld: ks_hostif.c:(.text+0xa6d): undefined reference to `crypto_destroy_tfm'
Commit 723de0f9171e ("staging: most: remove device from interface
structure") moved registration of driver-provided struct device to
the most subsystem.
Dim2 used to register the same struct device to provide a custom device
attribute. This causes double-registration of the same struct device.
Fix that by moving the custom attribute to driver's dev_groups.
This moves attribute to the platform_device object, which is a better
location for platform-specific attributes anyway.
The kconfig symbol GENERIC_PHY says:
All the users of this framework should select this config.
and around 136 out of 138 drivers do so, so change USB_MUSB_MEDIATEK
to do so also.
This (also) fixes a long circular dependency problem for an upcoming
patch.
Fixes: 0990366bab3c ("usb: musb: Add support for MediaTek musb controller") Cc: Bin Liu <b-liu@ti.com> Cc: Min Guo <min.guo@mediatek.com> Cc: Yonglong Wu <yonglong.wu@mediatek.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-mediatek@lists.infradead.org Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20211005235747.5588-1-rdunlap@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The error flow fixed in this patch is not possible because all kernel
users of create QP interface check that device supports steering before
set IB_QP_CREATE_NETIF_QP flag.
This variable is just a temporary variable, used to do an endian
conversion. The problem is that the last byte is not initialized. After
the conversion is completely done, the last byte is discarded so it doesn't
cause a problem. But static checkers and the KMSan runtime checker can
detect the uninitialized read and will complain about it.
Link: https://lore.kernel.org/r/20211006073242.GA8404@kili Fixes: 5036f0a0ecd3 ("[SCSI] csiostor: Fix sparse warnings.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The result of vcpu_is_preempted() is always used speculatively, and the
function does not access per-cpu resources in a (Linux) preempt-unsafe way.
Use raw_smp_processor_id() to avoid such warnings, adding explanatory
comments.
Fixes: ca3f969dcb11 ("powerpc/paravirt: Use is_kvm_guest() in vcpu_is_preempted()") Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com> Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210928214147.312412-3-nathanl@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When check_kvm_guest() succeeds in looking up a /hypervisor OF node, it
returns without performing a matching put for the lookup, leaving the
node's reference count elevated.
Add the necessary call to of_node_put(), rearranging the code slightly to
avoid repetition or goto.
This is due to 'dcbz' instruction being used on non-cached memory.
'dcbz' instruction is used by memset() to zeroize a complete
cacheline at once, and memset() is not expected to be used on non
cached memory.
When performing a 'sparse' check on fbdev driver, it also appears
that the use of memset() is unexpected:
drivers/video/fbdev/chipsfb.c:334:17: warning: incorrect type in argument 1 (different address spaces)
drivers/video/fbdev/chipsfb.c:334:17: expected void *
drivers/video/fbdev/chipsfb.c:334:17: got char [noderef] __iomem *screen_base
drivers/video/fbdev/chipsfb.c:334:15: warning: memset with byte count of 1048576
Use fb_memset() instead of memset(). fb_memset() is defined as
memset_io() for powerpc.
Commit 8e11d62e2e87 ("powerpc/mem: Add back missing header to fix 'no
previous prototype' error") was supposed to fix the problem, but in
the meantime commit a927bd6ba952 ("mm: fix phys_to_target_node() and*
memory_add_physaddr_to_nid() exports") moved create_section_mapping()
prototype from asm/sparsemem.h to asm/mmzone.h
Currently, at91 pmc driver always register the syscore_ops whatever
the status of the pmc node that has been found. When set as secure
and disabled, the pmc should not be accessed or this will generate
abort exceptions.
To avoid this, add a check on node availability before registering
the syscore operations.
The error handling code of fsl_ifc_ctrl_probe is problematic. When
fsl_ifc_ctrl_init fails or request_irq of fsl_ifc_ctrl_dev->irq fails,
it forgets to free the irq and nand_irq. Meanwhile, if request_irq of
fsl_ifc_ctrl_dev->nand_irq fails, it will still free nand_irq even if
the request_irq is not successful.
Fix this by refactoring the error handling code.
Fixes: d2ae2e20fbdd ("driver/memory:Move Freescale IFC driver to a common driver") Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Link: https://lore.kernel.org/r/20210925151434.8170-1-mudongliangabcd@gmail.com Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a successful tegra_powergate_enable_clocks()
call, it must be undone by a tegra_powergate_disable_clocks() call, as
already done in the below and above error handling paths of this function.
Update the 'goto' to branch at the correct place of the error handling
path.
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding SPI IDs for parts that
only have a compatible listed.
Fixes: 96c8395e2166 ("spi: Revert modalias changes") Signed-off-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20210927134153.12739-1-broonie@kernel.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When removing the topology components, do not power down
the primary core. Doing so will result in an IPC timeout
when the SOF PCI device runtime suspends.
Fixes: 0dcdf84289fb ("ASoC: SOF: add a "core" parameter to widget loading functions") Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Link: https://lore.kernel.org/r/20211006104041.27183-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When device_register() returns an error, the name allocated in dev_set_name()
will be leaked, the put_device() should be used instead of kfree() to give up
the device reference, then the name will be freed in kobject_cleanup() and the
references of consumer and supplier will be decreased in device_link_release_fn().
Fixes: 287905e68dd2 ("driver core: Expose device link details in sysfs") Reported-by: Hulk Robot <hulkci@huawei.com> Reviewed-by: Saravana Kannan <saravanak@google.com> Reviewed-by: Rafael J. Wysocki <rafael@kernel.org> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20210930085714.2057460-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
IRQ polling thread calls ISR after enable_irq() to handle any missed I/O
completion. The atomic flag "in_used" was added to have the synchronization
between the IRQ polling thread and the interrupt context. There is a bug
around it leading to a race condition.
Below is the sequence:
- IRQ polling thread accesses ISR, fetches the reply descriptor.
- Real interrupt arrives and pre-empts polling thread (enable_irq() is
already called).
- Interrupt context picks the same reply descriptor as fetched by polling
thread, processes it, and exits.
- Polling thread resumes and processes the descriptor which is already
processed by interrupt thread leads to kernel crash.
Setting the "in_used" flag before fetching the reply descriptor ensures
synchronized access to ISR.
link_id can be zero and if we have multiple controller instances
in a system like Qualcomm debugfs will end-up with duplicate namespace
resulting in incorrect debugfs entries.
Using bus-id and link-id combination should give a unique debugfs directory
entry and should fix below warning too.
"debugfs: Directory 'master-0' with parent 'soundwire' already present!"
The commit f87e7f25893d ("ALSA: hda - Improved position reporting on
SKL+") changed the PCM position report for SKL+ chips to use DPIB, but
according to Pierre, DPIB is no best choice for the accurate position
reports and it often reports too early. The recommended method is
rather the classical position buffer.
This patch makes the PCM position reporting on SKL+ back to the
position buffer again.
The position reporting on Intel Skylake and later chips via
azx_get_pos_skl() contains a udelay(20) call for the capture streams.
A call for this alone doesn't sound too harmful. However, as the
pointer PCM ops is one of the hottest path in the PCM operations --
especially for the timer-scheduled operations like PulseAudio -- such
a delay hogs CPU usage significantly in the total performance.
The code there was taken from the original code in ASoC SST Skylake
driver blindly. The udelay() is a workaround for the case where the
reported position is behind the period boundary at the timing
triggered from interrupts; applications often expect that the full
data is available for the whole period when returned (and also that's
the definition of the ALSA PCM period).
OTOH, HD-audio (legacy) driver has already some workarounds for the
delayed position reporting due to its relatively large FIFO, such as
the BDL position adjustment and the delayed period-elapsed call in the
work. That said, the udelay() is almost superfluous for HD-audio
driver unlike SST, and we can drop the udelay().
Though, the current code doesn't guarantee the full period readiness
as mentioned in the above, but rather it checks the wallclock and
detects the unexpected jump. That's one missing piece, and the drop
of udelay() needs a bit more sanity checks for the delayed handling.
This patch implements those: the drop of udelay() call in
azx_get_pos_skl() and the more proper check of hwptr in
azx_position_ok(). The latter change is applied only for the case
where the stream is running in the normal mode without
no_period_wakeup flag. When no_period_wakeup is set, it essentially
ignores the period handling and rather concentrates only on the
current position; which implies that we don't need to care about the
period boundary at all.
When calling arch_sync_dma, we need to pass it the memory that's
actually being used for dma. When using swiotlb bounce buffers, this is
the bounce buffer. Move arch_sync_dma into the __iommu_dma_map_swiotlb
helper, so it can use the bounce buffer address if necessary.
Now that iommu_dma_map_sg delegates to a function which takes care of
architectural syncing in the untrusted device case, the call to
iommu_dma_sync_sg_for_device can be moved so it only occurs for trusted
devices. Doing the sync for untrusted devices before mapping never
really worked, since it needs to be able to target swiotlb buffers.
This also moves the architectural sync to before the call to
__iommu_dma_map, to guarantee that untrusted devices can't see stale
data they shouldn't see.
Fixes: 82612d66d51d ("iommu: Allow the iommu/dma api to use bounce buffers") Signed-off-by: David Stevens <stevensd@chromium.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Link: https://lore.kernel.org/r/20210929023300.335969-3-stevensd@google.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
While removing the size from the "reg" properties in pm8916.dtsi,
commit bd6429e81010 ("ARM64: dts: qcom: Remove size elements from
pmic reg properties") mistakenly also removed the second register
address for the rtc@6000 device. That one did not represent the size
of the register region but actually the address of the second "alarm"
register region of the rtc@6000 device.
Now there are "reg-names" for two "reg" elements, but there is actually
only one "reg" listed.
Since the DT schema for "qcom,pm8941-rtc" only expects one "reg"
element anyway, just drop the "reg-names" entirely to fix this.
Fixes: bd6429e81010 ("ARM64: dts: qcom: Remove size elements from pmic reg properties") Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20210928112945.25310-1-stephan@gerhold.net Signed-off-by: Sasha Levin <sashal@kernel.org>
clang-14 notices that a comparison is never true when
CONFIG_PHYS_ADDR_T_64BIT is disabled:
drivers/iommu/mtk_iommu.c:553:34: error: result of comparison of constant 5368709120 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (dom->data->enable_4GB && pa >= MTK_IOMMU_4GB_MODE_REMAP_BASE)
~~ ^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Add an explicit check for the type of the variable to skip the check
and the warning in that case.
Fixes: b4dad40e4f35 ("iommu/mediatek: Adjust the PA for the 4GB Mode") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Yong Wu <yong.wu@mediatek.com> Link: https://lore.kernel.org/r/20210927121857.941160-1-arnd@kernel.org Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
While networking works fine in RGMII mode when using the Linux generic
PHY driver, it fails when using the Atheros PHY driver.
Fix this by correcting the Ethernet PHY mode to RGMII-RXID, which works
fine with both drivers.
At the moment, playing audio on Secondary MI2S will just end up getting
stuck, without actually playing any audio. This happens because the wrong
bit clock is configured when playing audio on Secondary MI2S.
The PRI_I2S_CLK (better name: SPKR_I2S_CLK) is used by the SPKR audio mux
block that provides both Primary and Secondary MI2S.
The SEC_I2S_CLK (better name: MIC_I2S_CLK) is used by the MIC audio mux
block that provides Tertiary MI2S. Quaternary MI2S is also part of the
MIC audio mux but has its own clock (AUX_I2S_CLK).
This means that (quite confusingly) the SEC_I2S_CLK is not actually
used for Secondary MI2S as the name would suggest. Secondary MI2S
needs to have the same clock as Primary MI2S configured.
Fix the clock list for the lpass node in the device tree and add
a comment to clarify this confusing naming. With these changes,
audio can be played correctly on Secondary MI2S.
The versioning scheme was changed in an earlier patch, which caused the version
being used to initialize WCD9335 to be interpreted as if it was WCD937X, which
changed code paths causing broken headphones output. Pass WCD9335 instead of
WCD9335_VERSION_2_0 to wcd_clsh_ctrl_alloc to fix it.
Fixes: 19c5d1f6a0c3 ("ASoC: codecs: wcd-clsh: add new version support") Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com> Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20210925022339.786296-1-y.oudjana@protonmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
mach/loongson64 fails to build when the FPU support is disabled:
arch/mips/loongson64/cop2-ex.c:45:15: error: implicit declaration of function ‘__is_fpu_owner’; did you mean ‘is_fpu_owner’? [-Werror=implicit-function-declaration]
arch/mips/loongson64/cop2-ex.c:98:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:99:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:131:43: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:137:38: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:203:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:219:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:283:38: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:301:38: error: ‘struct thread_struct’ has no member named ‘fpu’
dc395x_init_one()->adapter_init() might fail. In this case, the acb is
already cleaned up by adapter_init(), no need to do that in
adapter_uninit(acb) again.
The sc7180's dynamic-power-coefficient violates the device tree bindings.
The bindings (arm/cpus.yaml) say that the units for the
dynamic-power-coefficient are supposed to be "uW/MHz/V^2". The ones for
sc7180 aren't this. Qualcomm arbitrarily picked 100 for the "little" CPUs
and then picked a number for the big CPU based on this.
At the time, there was a giant dicussion about this. Apparently Qualcomm
Engineers were instructed not to share the actual numbers here. As part
of the discussion, I pointed out [1] that these numbers shouldn't really
be secret since once a device is shipping anyone can just run a script
and produce them. This patch is the result of running the script I posted
in that discussion on sc7180-trogdor-coachz, which is currently available
for purchase by consumers.
As you can see, the calculations aren't perfectly consistent but
roughly you could say about 480 for big and 137 for little.
The ratio between these numbers isn't quite the same as the ratio
between the two numbers that Qualcomm used. Perhaps this is because
Qualcomm measured something slightly different than the 64-bit version
of dhrystone 2.2 or perhaps it's because they fudged these numbers a
bit (and fudged the capacity-dmips-mhz). As per discussion [2], let's
use the numbers I came up with and also un-fudge
capacity-dmips-mhz. While unfudging capacity-dmips-mhz, let's scale it
so that bigs are 1024 which seems to be the common practice.
In general these numbers don't need to be perfectly exact. In fact,
they can't be since the CPU power depends a lot on what's being run on
the CPU and the big/little CPUs are each more or less efficient in
different operations. Historically running the 32-bit vs. 64-bit
versions of dhrystone produced notably different numbers, though I
didn't test this time.
We also need to scale all of the sustainable-power numbers by the same
amount. I scale ones related to the big CPUs by the adjustment I made
to the big dynamic-power-coefficient and the ones related to the
little CPUs by the adjustment I made to the little
dynamic-power-coefficient.
This went unnoticed until commit 7897b071ac3b ("net: macb: convert
to phylink") which tickled the problem. The sama5d3 emac has never
been capable of rgmii, and it all just happened to work before that
commit.
Fixes: 21dd0ece34c2 ("ARM: dts: at91: add devicetree for the Axentia TSE-850") Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/ea781f5e-422f-6cbf-3cf4-d5a7bac9392d@axentia.se Signed-off-by: Sasha Levin <sashal@kernel.org>
On resume we can get a warning at kernel/time/timekeeping.c:824 for
timekeeping_suspended.
Let's fix this by adding separate functions for sysc_poll_reset_sysstatus()
and sysc_poll_reset_sysconfig() and have the new functions handle also
timekeeping_suspended.
If iopoll at some point supports timekeeping_suspended, we can just drop
the custom handling from these functions.
Fixes: d46f9fbec719 ("bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After enabling CONFIG_REGULATOR_DEBUG=y we observe below debug logs.
Changes help link VDDCPU pwm regulator to 12V regulator supply
instead of dummy regulator.
[ 11.602281] pwm-regulator regulator-vddcpu: Looking up pwm-supply property
in node /regulator-vddcpu failed
[ 11.602344] VDDCPU: supplied by regulator-dummy
[ 11.602365] regulator-dummy: could not add device link regulator.11: -ENOENT
[ 11.602548] VDDCPU: 721 <--> 1022 mV at 1022 mV, enabled
Fixes: 88d537bc92ca ("arm64: dts: meson: convert meson-sm1-odroid-c4 to dtsi") Fixes: 700ab8d83927 ("arm64: dts: khadas-vim3: add support for the SM1 based VIM3L") Fixes: 3d9e76483049 ("arm64: dts: meson-sm1-sei610: enable DVFS") Fixes: 976e920183e4 ("arm64: dts: meson-sm1: add Banana PI BPI-M5 board dts") Cc: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Anand Moon <linux.amoon@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20210919202918.3556-4-linux.amoon@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
After enabling CONFIG_REGULATOR_DEBUG=y we observer below debug logs.
Changes help link VDDCP_A and VDDCPU_B pwm regulator to 12V regulator
supply instead of dummy regulator.
[ 4.147196] VDDCPU_A: will resolve supply early: pwm
[ 4.147216] pwm-regulator regulator-vddcpu-a: Looking up pwm-supply from device tree
[ 4.147227] pwm-regulator regulator-vddcpu-a: Looking up pwm-supply property in node /regulator-vddcpu-a failed
[ 4.147258] VDDCPU_A: supplied by regulator-dummy
[ 4.147288] regulator-dummy: could not add device link regulator.12: -ENOENT
[ 4.147353] VDDCPU_A: 721 <--> 1022 mV at 871 mV, enabled
[ 4.152014] VDDCPU_B: will resolve supply early: pwm
[ 4.152035] pwm-regulator regulator-vddcpu-b: Looking up pwm-supply from device tree
[ 4.152047] pwm-regulator regulator-vddcpu-b: Looking up pwm-supply property in node /regulator-vddcpu-b failed
[ 4.152079] VDDCPU_B: supplied by regulator-dummy
[ 4.152108] regulator-dummy: could not add device link regulator.13: -ENOENT
Fixes: c6d29c66e582 ("arm64: dts: meson-g12b-khadas-vim3: add initial device-tree") Fixes: d14734a04a8a ("arm64: dts: meson-g12b-odroid-n2: enable DVFS") Fixes: 3cb74db9b256 ("arm64: dts: meson: convert ugoos-am6 to common w400 dtsi") Cc: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Anand Moon <linux.amoon@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20210919202918.3556-3-linux.amoon@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
After enabling CONFIG_REGULATOR_DEBUG=y we observe below debug logs.
Changes help link VDDCPU pwm regulator to 12V regulator supply
instead of dummy regulator.
[ 11.602281] pwm-regulator regulator-vddcpu: Looking up pwm-supply property
in node /regulator-vddcpu failed
[ 11.602344] VDDCPU: supplied by regulator-dummy
[ 11.602365] regulator-dummy: could not add device link regulator.11: -ENOENT
[ 11.602548] VDDCPU: 721 <--> 1022 mV at 1022 mV, enabled
Fixes: e9bc0765cc12 ("arm64: dts: meson-g12a: enable DVFS on G12A boards") Cc: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Anand Moon <linux.amoon@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20210919202918.3556-2-linux.amoon@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3276d9f53cf6 ("arm64: dts: ti: k3-j7200-main: Add PCIe device
tree node") incorrectly added PCIe bus numbers from 0 to 15 (copy-paste
from J721E node). Enable all the supported bus numbers from 0 to 255
defined in PCIe spec here.
commit 3276d9f53cf6 ("arm64: dts: ti: k3-j7200-main: Add PCIe device
tree node") incorrectly added "vendor-id" and "device-id" as 16-bit
properties though both of them are 32-bit properties. Fix it here.
commit 4e5833884f66 ("arm64: dts: ti: k3-j721e-main: Add PCIe device
tree nodes") restricted PCIe bus numbers from 0 to 15 (due to SMMU
restriction in J721E). However since SMMU is not enabled, allow the full
supported bus numbers from 0 to 255.
commit 4e5833884f66 ("arm64: dts: ti: k3-j721e-main: Add PCIe device
tree nodes") added "max-virtual-functions" to have 16 bit values.
Fix "max-virtual-functions" in PCIe endpoint (EP) nodes to have 8 bit
values instead of 16.
According to YAML validation, and for a future patchset putting this
xo_board reference clock to use as VCO reference parent, add the missing
clock to dsi_phy0.
As can be seen in RK3328's TRM the register range for the GPU is
0xff300000 to 0xff330000.
It would (and does in vendor kernel) overlap with the registers of
the HEVC encoder (node/driver do not exist yet in upstream kernel).
See already existing h265e_mmu node.
Commit 1f02beff224e ("scsi: pm80xx: Remove global lock from outbound queue
processing") introduced a lock per outbound queue. Prior to that change the
driver was using a global lock for all outbound queues.
While processing the I/O responses and events the driver takes the outbound
queue spinlock and is supposed to release it in pm8001_ccb_task_free_done()
before calling command done(). Since the older code was using a global
lock, pm8001_ccb_task_free_done() was releasing the global spin lock. The
change that split the lock per outbound queue did not consider this and
pm8001_ccb_task_free_done() was still releasing the global lock.
Link: https://lore.kernel.org/r/20210906170404.5682-3-Ajish.Koshy@microchip.com Fixes: 1f02beff224e ("scsi: pm80xx: Remove global lock from outbound queue processing") Acked-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com> Signed-off-by: Viswas G <Viswas.G@microchip.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Up until commit ea7e586bdd331 ("iio: st_sensors: move regulator retrieveal
to core") only the ST pressure driver seems to have had any regulator
disable. After that commit, the regulator handling was moved into the
common st_sensors logic.
In all instances of this regulator handling, the regulators were disabled
before unregistering the IIO device.
This can cause issues where the device would be powered down and still be
available to userspace, allowing it to send invalid/garbage data.
This change moves the st_sensors_power_disable() after the common probe
functions. These common probe functions also handle unregistering the IIO
device.
Fixes: 774487611c949 ("iio: pressure-core: st: Provide support for the Vdd power supply") Fixes: ea7e586bdd331 ("iio: st_sensors: move regulator retrieveal to core") Cc: Lee Jones <lee.jones@linaro.org> Cc: Denis CIOCCA <denis.ciocca@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com> Link: https://lore.kernel.org/r/20210823112204.243255-2-aardelean@deviqon.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch is to fix an issue that the ethernet link doesn't come up
when using ip link set down/up:
[ 11.428114] meson8b-dwmac ff3f0000.ethernet eth0: Link is Down
[ 14.428595] meson8b-dwmac ff3f0000.ethernet eth0: PHY [0.0:00] driver [RTL8211F Gigabit Ethernet] (irq=31)
[ 14.428610] meson8b-dwmac ff3f0000.ethernet: Failed to reset the dma
[ 14.428974] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[ 14.711185] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Hw setup failed
This fix refers to two commits applied for ODROID-N2 (G12B).
commit 658e4129bb81 ("arm64: dts: meson: g12b: odroid-n2: add the Ethernet PHY reset line")
commit 1c7412530d5d0 ("arm64: dts: meson: g12b: odroid-n2: fix PHY deassert timing requirements")
Fixes: 88d537bc92ca ("arm64: dts: meson: convert meson-sm1-odroid-c4 to dtsi") Signed-off-by: Dongjin Kim <tobetter@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[narmstrong: added fixes tag and typo in commit log] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/YScKYFWlYymgGw3l@anyang-linuxfactory-or-kr Signed-off-by: Sasha Levin <sashal@kernel.org>
Before this fix:
166: (b5) if r2 <= 0x1 goto pc+22
from 166 to 189: R2=invP(id=1,umax_value=1,var_off=(0x0; 0xffffffff))
After this fix:
166: (b5) if r2 <= 0x1 goto pc+22
from 166 to 189: R2=invP(id=1,umax_value=1,var_off=(0x0; 0x1))
While processing BPF_JLE the reg_set_min_max() would set true_reg->umax_value = 1
and call __reg_combine_64_into_32(true_reg).
Without the fix it would not pass the condition:
if (__reg64_bound_u32(reg->umin_value) && __reg64_bound_u32(reg->umax_value))
since umin_value == 0 at this point.
Before commit 10bf4e83167c the umin was incorrectly ingored.
The commit 10bf4e83167c fixed the correctness issue, but pessimized
propagation of 64-bit min max into 32-bit min max and corresponding var_off.
Fixes: 10bf4e83167c ("bpf: Fix propagation of 32 bit unsigned bounds from 64 bit bounds") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20211101222153.78759-1-alexei.starovoitov@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In account_guest_time in kernel/sched/cputime.c guest time is
attributed to both CPUTIME_NICE and CPUTIME_USER in addition to
CPUTIME_GUEST_NICE and CPUTIME_GUEST respectively. Therefore, adding
both to calculate usage results in double counting any guest time at
the rootcg.
If sockmap enable strparser, there are lose offset info in
sk_psock_skb_ingress(). If the length determined by parse_msg function is not
skb->len, the skb will be converted to sk_msg multiple times, and userspace
app will get the data multiple times.
Fix this by get the offset and length from strp_msg. And as Cong suggested,
add one bit in skb->_sk_redir to distinguish enable or disable strparser.
Fixes: 604326b41a6fb ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Liu Jian <liujian56@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Cong Wang <cong.wang@bytedance.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20211029141216.211899-1-liujian56@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If we get CRQ_INIT, we set errno to -EIO and first call complete() to
notify the waiter. Then we try to schedule a FAILOVER reset. If this
occurs while adapter is in PROBING state, ibmvnic_reset() changes the
error code to EAGAIN and returns without scheduling the FAILOVER. The
purpose of setting error code to EAGAIN is to ask the waiter to retry.
But due to the earlier complete() call, the waiter may already have seen
the -EIO response and decided not to retry. This can cause intermittent
failures when bringing up ibmvnic adapters during boot, specially in
in kexec/kdump kernels.
Defer the complete() call until after scheduling the reset.
Also streamline the error code to EAGAIN. Don't see why we need EIO
sometimes. All 3 callers of ibmvnic_reset_init() can handle EAGAIN.
Fixes: 17c8705838a5 ("ibmvnic: Return error code if init interrupted by transport event") Reported-by: Vaishnavi Bhat <vaish123@in.ibm.com> Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Reviewed-by: Dany Madden <drt@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Soon after registering a CRQ it is possible that we get a fail over or
maybe a CRQ_INIT from the VIOS while interrupts were disabled.
Look for any such CRQs after enabling interrupts.
Otherwise we can intermittently fail to bring up ibmvnic adapters during
boot, specially in kexec/kdump kernels.
Fixes: 032c5e82847a ("Driver for IBM System i/p VNIC protocol") Reported-by: Vaishnavi Bhat <vaish123@in.ibm.com> Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Reviewed-by: Dany Madden <drt@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If adapter's resetting bit is on, discard the packet but don't stop the
transmit queue - instead leave that to the reset code. With this change,
it is possible that we may get several calls to ibmvnic_xmit() that simply
discard packets and return.
But if we stop the queue here, we might end up doing so just after
__ibmvnic_open() started the queues (during a hard/soft reset) and before
the ->resetting bit was cleared. If that happens, there will be no one to
restart queue and transmissions will be blocked indefinitely.
This can cause a TIMEOUT reset and with auto priority failover enabled,
an unnecessary FAILOVER reset to less favored backing device and then a
FAILOVER back to the most favored backing device. If we hit the window
repeatedly, we can get stuck in a loop of TIMEOUT, FAILOVER, FAILOVER
resets leaving the adapter unusable for extended periods of time.
Fixes: 7f5b030830fe ("ibmvnic: Free skb's in cases of failure in transmit") Reported-by: Abdul Haleem <abdhalee@in.ibm.com> Reported-by: Vaishnavi Bhat <vaish123@in.ibm.com> Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Reviewed-by: Dany Madden <drt@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit c6af0c227a22 ("ip: support SO_MARK cmsg")
added propagation of SO_MARK from cmsg to skb->mark.
For IPv4 and raw sockets the mark also affects route
lookup, but in case of IPv6 the flow info is
initialized before cmsg is parsed.
Fixes: c6af0c227a22 ("ip: support SO_MARK cmsg") Reported-and-tested-by: Xintong Hu <huxintong@fb.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: David Ahern <dsahern@kernel.org> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
These three events can race when pcrypt is used multiple times in a
template ("pcrypt(pcrypt(...))"):
1. [taskA] The caller makes the crypto request via crypto_aead_encrypt()
2. [kworkerB] padata serializes the inner pcrypt request
3. [kworkerC] padata serializes the outer pcrypt request
3 might finish before the call to crypto_aead_encrypt() returns in 1,
resulting in two possible issues.
First, a use-after-free of the crypto request's memory when, for
example, taskA writes to the outer pcrypt request's padata->info in
pcrypt_aead_enc() after kworkerC completes the request.
Second, the outer pcrypt request overwrites the inner pcrypt request's
return code with -EINPROGRESS, making a successful request appear to
fail. For instance, kworkerB writes the outer pcrypt request's
padata->info in pcrypt_aead_done() and then taskA overwrites it
in pcrypt_aead_enc().
Avoid both situations by delaying the write of padata->info until after
the inner crypto request's return code is checked. This prevents the
use-after-free by not touching the crypto request's memory after the
next-inner crypto request is made, and stops padata->info from being
overwritten.
Fixes: 5068c7a883d16 ("crypto: pcrypt - Add pcrypt crypto parallelization wrapper") Reported-by: syzbot+b187b77c8474f9648fae@syzkaller.appspotmail.com Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When I fixed IGMPv3/MLDv2 to use the bridge's multicast_membership_interval
value which is chosen by user-space instead of calculating it based on
multicast_query_interval and multicast_query_response_interval I forgot
to update the selftests relying on that behaviour. Now we have to
manually set the expected GMI value to perform the tests correctly and get
proper results (similar to IGMPv2 behaviour).
Fixes: fac3cb82a54a ("net: bridge: mcast: use multicast_membership_interval for IGMPv3") Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function br_get_link_af_size_filtered() calls br_cfm_{,peer}_mep_count()
that return a count. When BRIDGE_CFM is not enabled these functions
simply return -EOPNOTSUPP but do not modify count parameter and
calling function then works with uninitialized variables.
Modify these inline functions to return zero in count parameter.
Fixes: b6d0425b816e ("bridge: cfm: Netlink Notifications.") Cc: Henrik Bjoernlund <henrik.bjoernlund@microchip.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
mvneta does not support asymetric pause modes, and it flags this by the
lack of AsymPause in the supported field. When setting pause modes, we
check that pause->rx_pause == pause->tx_pause, but only when pause
autoneg is enabled. When pause autoneg is disabled, we still allow
pause->rx_pause != pause->tx_pause, which is incorrect when the MAC
does not support asymetric pause, and causes mvneta to issue a warning.
Fix this by removing the test for pause->autoneg, so we always check
that pause->rx_pause == pause->tx_pause for network devices that do not
support AsymPause.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure") Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
For each rate change command submission, the FW has to do a phy
power off sequence internally. For this to happen correctly, the
PLL re-initialization control setting has to be turned off before
sending mailbox commands and re-enabled once the command submission
is complete.
Without the PLL control setting, the link up takes longer time in a
fixed phy configuration.
Fixes: 47f164deab22 ("amd-xgbe: Add PCI device support") Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
