Replace the 32bit exec_id with a 64bit exec_id to make it impossible
to wrap the exec_id counter. With care an attacker can cause exec_id
wrap and send arbitrary signals to a newly exec'd parent. This
bypasses the signal sending checks if the parent changes their
credentials during exec.
The severity of this problem can been seen that in my limited testing
of a 32bit exec_id it can take as little as 19s to exec 65536 times.
Which means that it can take as little as 14 days to wrap a 32bit
exec_id. Adam Zabrocki has succeeded wrapping the self_exe_id in 7
days. Even my slower timing is in the uptime of a typical server.
Which means self_exec_id is simply a speed bump today, and if exec
gets noticably faster self_exec_id won't even be a speed bump.
Extending self_exec_id to 64bits introduces a problem on 32bit
architectures where reading self_exec_id is no longer atomic and can
take two read instructions. Which means that is is possible to hit
a window where the read value of exec_id does not match the written
value. So with very lucky timing after this change this still
remains expoiltable.
I have updated the update of exec_id on exec to use WRITE_ONCE
and the read of exec_id in do_notify_parent to use READ_ONCE
to make it clear that there is no locking between these two
locations.
When TPC is disabled IEEE80211_CONF_CHANGE_POWER event can be handled to
reconfigure HW's maximum txpower.
This fixes 0dBm txpower setting when user attaches to an interface for
the first time with the following scenario:
ieee80211_do_open()
ath9k_add_interface()
ath9k_set_txpower() /* Set TX power with not yet initialized
sc->hw->conf.power_level */
ieee80211_hw_config() /* Iniatilize sc->hw->conf.power_level and
raise IEEE80211_CONF_CHANGE_POWER */
ath9k_config() /* IEEE80211_CONF_CHANGE_POWER is ignored */
This issue can be reproduced with the following:
$ modprobe -r ath9k
$ modprobe ath9k
$ wpa_supplicant -i wlan0 -c /tmp/wpa.conf &
$ iw dev /* Here TX power is either 0 or 3 depending on RF chain */
$ killall wpa_supplicant
$ iw dev /* TX power goes back to calibrated value and subsequent
calls will be fine */
Fixes: 283dd11994cde ("ath9k: add per-vif TX power capability") Cc: stable@vger.kernel.org Signed-off-by: Remi Pommarel <repk@triplefau.lt> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear its own IRQs before the parent IRQ get enabled, so that the
remaining IRQs do not accidentally interrupt the parent IRQ controller.
This patch also fixes a reboot bug on OX820 SoC, where the remaining
rps-timer IRQ raises a GIC interrupt that is left pending. After that,
the rps-timer IRQ is cleared during driver initialization, and there's
no IRQ left in rps-irq when local_irq_enable() is called, which evokes
an error message "unexpected IRQ trap".
Fixes: bdd272cbb97a ("irqchip: versatile FPGA: support cascaded interrupts from DT") Signed-off-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200321133842.2408823-1-mans0n@gorani.run Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit a08bf91ce28e ("KEYS: allow reaching the keys quotas exactly"),
we can reach max bytes/keys in key_alloc, but we forget to remove this
limit when we reserver space for payload in key_payload_reserve. So we
can only reach max keys but not max bytes when having delta between plen
and type->def_datalen. Remove this limit when instantiating the key, so we
can keep consistent with key_alloc.
Also, fix the similar problem in keyctl_chown_key().
Fixes: 0b77f5bfb45c ("keys: make the keyring quotas controllable through /proc/sys") Fixes: a08bf91ce28e ("KEYS: allow reaching the keys quotas exactly") Cc: stable@vger.kernel.org # 5.0.x Cc: Eric Biggers <ebiggers@google.com> Signed-off-by: Yang Xu <xuyang2018.jy@cn.fujitsu.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_DEVFREQ_THERMAL is disabled all functions except
of_devfreq_cooling_register_power() were already inlined. Also inline
the last function to avoid compile errors when multiple drivers call
of_devfreq_cooling_register_power() when CONFIG_DEVFREQ_THERMAL is not
set. Compilation failed with the following message:
multiple definition of `of_devfreq_cooling_register_power'
(which then lists all usages of of_devfreq_cooling_register_power())
Thomas Zimmermann reported this problem [0] on a kernel config with
CONFIG_DRM_LIMA={m,y}, CONFIG_DRM_PANFROST={m,y} and
CONFIG_DEVFREQ_THERMAL=n after both, the lima and panfrost drivers
gained devfreq cooling support.
The value in "new" is constructed from "old" such that all bits defined
as reserved by the ACPI spec[1] are left untouched. But if those bits
do not happen to be all zero, "new < 3" will not evaluate to true.
The firmware of the laptop(s) Medion MD63490 / Akoya P15648 comes with
garbage inside the "FACS" ACPI table. The starting value is
old=0x4944454d, therefore new=0x4944454e, which is >= 3. Mask off
the reserved bits.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206553 Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Jan Engelhardt <jengelh@inai.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent fix for the OOB access in PCM OSS plugins (commit f2ecf903ef06: "ALSA: pcm: oss: Avoid plugin buffer overflow") caused a
regression on OSS applications. The patch introduced the size check
in client and slave size calculations to limit to each plugin's buffer
size, but I overlooked that some code paths call those without
allocating the buffer but just for estimation.
This patch fixes the bug by skipping the size check for those code
paths while keeping checking in the actual transfer calls.
The access to Analog Capture Source control value implemented in
prodigy_hifi.c is wrong, as caught by the recently introduced sanity
check; it should be accessing value.enumerated.item[] instead of
value.integer.value[]. This patch corrects the wrong access pattern.
The beep control helper function blindly stores the values in two
stereo channels no matter whether the actual control is mono or
stereo. This is practically harmless, but it annoys the recently
introduced sanity check, resulting in an error when the checker is
enabled.
This patch corrects the behavior to store only on the defined array
member.
The recent AMD platform exposes an HD-audio bus but without any actual
codecs, which is internally tied with a USB-audio device, supposedly.
It results in "no codecs" error of HD-audio bus driver, and it's
nothing but a waste of resources.
This patch introduces a static blacklist table for skipping such a
known bogus PCI SSID entry. As of writing this patch, the known SSIDs
are:
* 1043:874f - ASUS ROG Zenith II / Strix
* 1462:cb59 - MSI TRX40 Creator
* 1462:cb60 - MSI TRX40
Some recent boards (supposedly with a new AMD platform) contain the
USB audio class 2 device that is often tied with HD-audio. The device
exposes an Input Gain Pad control (id=19, control=12) but this node
doesn't behave correctly, returning an error for each inquiry of
GET_MIN and GET_MAX that should have been mandatory.
As a workaround, simply ignore this node by adding a usbmix_name_map
table entry. The currently known devices are:
* 0414:a002 - Gigabyte TRX40 Aorus Pro WiFi
* 0b05:1916 - ASUS ROG Zenith II
* 0b05:1917 - ASUS ROG Strix
* 0db0:0d64 - MSI TRX40 Creator
* 0db0:543d - MSI TRX40
Different configuration/condition may draw different power. Inform the
controller driver of the change so it can respond properly (e.g.
GET_STATUS request). This fixes an issue with setting MaxPower from
configfs. The composite driver doesn't check this value when setting
self-powered.
Cc: stable@vger.kernel.org Fixes: 88af8bbe4ef7 ("usb: gadget: the start of the configfs interface") Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In AIO case, the request is freed up if ep_queue fails.
However, io_data->req still has the reference to this freed
request. In the case of this failure if there is aio_cancel
call on this io_data it will lead to an invalid dequeue
operation and a potential use after free issue.
Fix this by setting the io_data->req to NULL when the request
is freed as part of queue failure.
soc_compr_trigger_fe() allows start or stop after pause_push.
In dpcm_be_dai_trigger(), however, only pause_release is allowed
command after pause_push.
So, start or stop after pause in compress offload is always
returned as error if the compress offload is used with dpcm.
To fix the problem, SND_SOC_DPCM_STATE_PAUSED should be allowed
for start or stop command.
Signed-off-by: Gyeongtaek Lee <gt82.lee@samsung.com> Reviewed-by: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/004d01d607c1$7a3d5250$6eb7f6f0$@samsung.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since a virtual mixer has no backing registers
to decide which path to connect,
it will try to match with initial state.
This is to ensure that the default mixer choice will be
correctly powered up during initialization.
Invert flag is used to select initial state of the virtual switch.
Since actual hardware can't be disconnected by virtual switch,
connected is better choice as initial state in many cases.
If regwshift is 32 and the selected architecture compiles '<<' operator
for signed int literal into rotating shift, '1<<regwshift' became 1 and
it makes regwmask to 0x0.
The literal is set to unsigned long to get intended regwmask.
We always search the commit root of the extent tree for looking up back
references, however we track the reloc roots based on their current
bytenr.
This is wrong, if we commit the transaction between relocating tree
blocks we could end up in this code in build_backref_tree
if (key.objectid == key.offset) {
/*
* Only root blocks of reloc trees use backref
* pointing to itself.
*/
root = find_reloc_root(rc, cur->bytenr);
ASSERT(root);
cur->root = root;
break;
}
find_reloc_root() is looking based on the bytenr we had in the commit
root, but if we've COWed this reloc root we will not find that bytenr,
and we will trip over the ASSERT(root).
Fix this by using the commit_root->start bytenr for indexing the commit
root. Then we change the __update_reloc_root() caller to be used when
we switch the commit root for the reloc root during commit.
This fixes the panic I was seeing when we started throttling relocation
for delayed refs.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This was pretty subtle, we default to reloc roots having 0 root refs, so
if we crash in the middle of the relocation they can just be deleted.
If we successfully complete the relocation operations we'll set our root
refs to 1 in prepare_to_merge() and then go on to merge_reloc_roots().
At prepare_to_merge() time if any of the reloc roots have a 0 reference
still, we will remove that reloc root from our reloc root rb tree, and
then clean it up later.
However this only happens if we successfully start a transaction. If
we've aborted previously we will skip this step completely, and only
have reloc roots with a reference count of 0, but were never properly
removed from the reloc control's rb tree.
This isn't a problem per-se, our references are held by the list the
reloc roots are on, and by the original root the reloc root belongs to.
If we end up in this situation all the reloc roots will be added to the
dirty_reloc_list, and then properly dropped at that point. The reloc
control will be free'd and the rb tree is no longer used.
There were two options when fixing this, one was to remove the BUG_ON(),
the other was to make prepare_to_merge() handle the case where we
couldn't start a trans handle.
IMO this is the cleaner solution. I started with handling the error in
prepare_to_merge(), but it turned out super ugly. And in the end this
BUG_ON() simply doesn't matter, the cleanup was happening properly, we
were just panicing because this BUG_ON() only matters in the success
case. So I've opted to just remove it and add a comment where it was.
Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The warning got triggered because lockdep_count_forward_deps() call
__bfs() without current->lockdep_recursion being set, as a result
a lockdep internal function (__bfs()) is checked by lockdep, which is
unexpected, and the inconsistency between the irq-off state and the
state traced by lockdep caused the warning.
Apart from this warning, lockdep internal functions like __bfs() should
always be protected by current->lockdep_recursion to avoid potential
deadlocks and data inconsistency, therefore add the
current->lockdep_recursion on-and-off section to protect __bfs() in both
lockdep_count_forward_deps() and lockdep_count_backward_deps()
Before this patch, run_queue would demote glocks based on whether
there are any more holders. But if the glock has pending revokes that
haven't been written to the media, giving up the glock might end in
file system corruption if the revokes never get written due to
io errors, node crashes and fences, etc. In that case, another node
will replay the metadata blocks associated with the glock, but
because the revoke was never written, it could replay that block
even though the glock had since been granted to another node who
might have made changes.
This patch changes the logic in run_queue so that it never demotes
a glock until its count of pending revokes reaches zero.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is also refcount issue, as well:
WARNING: CPU: 1 PID: 1 at lib/refcount.c:28 refcount_warn_saturate+0xf8/0x170
The issue is that we make an erroneous extra call to scsi_host_put()
for that host:
So in ahci_init_one()->ata_host_alloc_pinfo()->ata_host_alloc(), we setup
a device release method - ata_devres_release() - which intends to release
the SCSI hosts:
static void ata_devres_release(struct device *gendev, void *res)
{
...
for (i = 0; i < host->n_ports; i++) {
struct ata_port *ap = host->ports[i];
if (!ap)
continue;
if (ap->scsi_host)
scsi_host_put(ap->scsi_host);
}
...
}
However in the ata_scsi_add_hosts() error path, we also call
scsi_host_put() for the SCSI hosts.
Fix by removing the the scsi_host_put() calls in ata_scsi_add_hosts() and
leave this to ata_devres_release().
Fixes: f31871951b38 ("libata: separate out ata_host_alloc() and ata_host_register()") Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The same benchmark is running in group C & F, no other tasks are
running, the benchmark is capable to consumed all the CPUs.
We suppose the group C will win more CPU resources since it could
enjoy all the shares of group A, but it's F who wins much more.
The reason is because we have group B with shares as 2, since
A->cfs_rq.load.weight == B->se.load.weight == B->shares/nr_cpus,
so A->cfs_rq.load.weight become very small.
And in calc_group_shares() we calculate shares as:
Since the 'cfs_rq->load.weight' is too small, the load become 0
after scale down, although 'tg_shares' is 102400, shares of the se
which stand for group A on root cfs_rq become 2.
While the se of D on root cfs_rq is far more bigger than 2, so it
wins the battle.
Thus when scale_load_down() scale real weight down to 0, it's no
longer telling the real story, the caller will have the wrong
information and the calculation will be buggy.
This patch add check in scale_load_down(), so the real weight will
be >= MIN_SHARES after scale, after applied the group C wins as
expected.
Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Michael Wang <yun.wang@linux.alibaba.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org> Link: https://lkml.kernel.org/r/38e8e212-59a1-64b2-b247-b6d0b52d8dc1@linux.alibaba.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Enclose the chained handler with chained_irq_{enter,exit}(), so that the
muxed interrupts get properly acked.
This patch also fixes a reboot bug on OX820 SoC, where the jiffies timer
interrupt is never acked. The kernel waits a clock tick forever in
calibrate_delay_converge(), which leads to a boot hang.
printk in macro vxge_debug_ll uses __VA_ARGS__ without "##" prefix,
it causes a build error when there is no variable
arguments(e.g. only fmt is specified.).
Signed-off-by: Zheng Wei <wei.zheng@vivo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When doing a 16-bit read that returns data in the MSB byte, the
RSB_DATA register will keep the MSB byte unchanged when doing
the following 8-bit read. sunxi_rsb_read() will then return
a result that contains high byte from 16-bit read mixed with
the 8-bit result.
The consequence is that after this happens the PMIC's regmap will
look like this: (0x33 is the high byte from the 16-bit read)
Fix this by masking the result of the read with the correct mask
based on the size of the read. There are no 16-bit users in the
mainline kernel, so this doesn't need to get into the stable tree.
Signed-off-by: Ondrej Jirman <megous@megous.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
[subject was: drm/msm: shake fist angrily at dma-mapping]
So, using dma_sync_* for our cache needs works out w/ dma iommu ops, but
it falls appart with dma direct ops. The problem is that, depending on
display generation, we can have either set of dma ops (mdp4 and dpu have
iommu wired to mdss node, which maps to toplevel drm device, but mdp5
has iommu wired up to the mdp sub-node within mdss).
Fixes: 0036bc73ccbe (drm/msm: stop abusing dma_map/unmap for cache) Fixes: 449fa54d6815 (dma-direct: correct the physical addr in dma_direct_sync_sg_for_cpu/device) Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Rob Clark <robdclark@chromium.org>
[seanpaul changed subject to something more desriptive] Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190730214633.17820-1-robdclark@gmail.com Cc: nobuhiro1.iwamatsu@toshiba.co.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts
commit 6a4290cc28be1 ("usb: dwc3: gadget: set the OTG flag in dwc3 gadget driver.")
We don't yet support any of the OTG mechanisms (HNP/SRP/ADP)
and are not setting gadget->otg_caps, so don't set gadget->is_otg
flag.
If we do then we end up publishing a OTG1.0 descriptor in
the gadget descriptor which causes device enumeration to fail
if we are connected to a host with CONFIG_USB_OTG enabled.
Host side log without this patch
[ 96.720453] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 96.901391] usb 1-1: Dual-Role OTG device on non-HNP port
[ 96.907552] usb 1-1: set a_alt_hnp_support failed: -32
[ 97.060447] usb 1-1: new high-speed USB device number 3 using xhci-hcd
[ 97.241378] usb 1-1: Dual-Role OTG device on non-HNP port
[ 97.247536] usb 1-1: set a_alt_hnp_support failed: -32
[ 97.253606] usb usb1-port1: attempt power cycle
[ 97.960449] usb 1-1: new high-speed USB device number 4 using xhci-hcd
[ 98.141383] usb 1-1: Dual-Role OTG device on non-HNP port
[ 98.147540] usb 1-1: set a_alt_hnp_support failed: -32
[ 98.300453] usb 1-1: new high-speed USB device number 5 using xhci-hcd
[ 98.481391] usb 1-1: Dual-Role OTG device on non-HNP port
[ 98.487545] usb 1-1: set a_alt_hnp_support failed: -32
[ 98.493532] usb usb1-port1: unable to enumerate USB device
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__early_cpu_boot_status is of type long. Use quad
assembler directive to allocate proper size.
Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Arun KS <arunks@codeaurora.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not quite sure what triggered that, but we really shouldn't be abusing
dma_{map,unmap}_sg() for cache maint.
Cc: Stephen Boyd <sboyd@kernel.org> Tested-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190630124735.27786-1-robdclark@gmail.com Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reported that 4fbc0c711b24 ("ceph: remove the extra slashes in
the server path") had caused a regression where an allocation could be
done under a spinlock -- compare_mount_options() is called by sget_fc()
with sb_lock held.
We don't really need the supplied server path, so canonicalize it
in place and compare it directly. To make this work, the leading
slash is kept around and the logic in ceph_real_mount() to skip it
is restored. CEPH_MSG_CLIENT_SESSION now reports the same (i.e.
canonicalized) path, with the leading slash of course.
Fixes: 4fbc0c711b24 ("ceph: remove the extra slashes in the server path") Reported-by: syzbot+98704a51af8e3d9425a9@syzkaller.appspotmail.com Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Luis Henriques <lhenriques@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And then when creating any new file or directory under the mount
point, we can hit the following BUG_ON in ceph_fill_trace():
BUG_ON(ceph_snap(dir) != dvino.snap);
Have the client ignore the extra slashes in the server path when
mounting. This will also canonicalize the path, so that identical mounts
can be consilidated.
Regardless of the internal treatment of these paths, the kernel still
stores the original string including the leading '/' for presentation
to userland.
URL: https://tracker.ceph.com/issues/42771 Signed-off-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Luis Henriques <lhenriques@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Releasing dd->per_sdma[i].kobject in hfi1_unregister_sysfs().
- This will fix the memory leak.
- Calling kobject_put() to unwind operations only for those entries in
dd->per_sdma[] whose operations have succeeded (including the current
one that has just failed) in hfi1_verbs_register_sysfs().
Cc: <stable@vger.kernel.org> Fixes: 0cb2aa690c7e ("IB/hfi1: Add sysfs interface for affinity setup") Link: https://lore.kernel.org/r/20200326163807.21129.27371.stgit@awfm-01.aw.intel.com Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When kobject_init_and_add() returns an error in the function
hfi1_create_port_files(), the function kobject_put() is not called for the
corresponding kobject, which potentially leads to memory leak.
This patch fixes the issue by calling kobject_put() even if
kobject_init_and_add() fails.
Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200326163813.21129.44280.stgit@awfm-01.aw.intel.com Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent change to the netlink code: 6e237d099fac ("netlink: Relax attr
validation for fixed length types") logs a warning when programs send
messages with invalid attributes (e.g., wrong length for a u32). Yafang
reported this error message for tools/accounting/getdelays.c.
send_cmd() is wrongly adding 1 to the attribute length. As noted in
include/uapi/linux/netlink.h nla_len should be NLA_HDRLEN + payload
length, so drop the +1.
It turns out that RDRAND is pretty slow. Comparing these two
constructions:
for (i = 0; i < CHACHA_BLOCK_SIZE; i += sizeof(ret))
arch_get_random_long(&ret);
and
long buf[CHACHA_BLOCK_SIZE / sizeof(long)];
extract_crng((u8 *)buf);
it amortizes out to 352 cycles per long for the top one and 107 cycles
per long for the bottom one, on Coffee Lake Refresh, Intel Core i9-9880H.
And importantly, the top one has the drawback of not benefiting from the
real rng, whereas the bottom one has all the nice benefits of using our
own chacha rng. As get_random_u{32,64} gets used in more places (perhaps
beyond what it was originally intended for when it was introduced as
get_random_{int,long} back in the md5 monstrosity era), it seems like it
might be a good thing to strengthen its posture a tiny bit. Doing this
should only be stronger and not any weaker because that pool is already
initialized with a bunch of rdrand data (when available). This way, we
get the benefits of the hardware rng as well as our own rng.
Another benefit of this is that we no longer hit pitfalls of the recent
stream of AMD bugs in RDRAND. One often used code pattern for various
things is:
do {
val = get_random_u32();
} while (hash_table_contains_key(val));
That recent AMD bug rendered that pattern useless, whereas we're really
very certain that chacha20 output will give pretty distributed numbers,
no matter what.
So, this simplification seems better both from a security perspective
and from a performance perspective.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20200221201037.30231-1-Jason@zx2c4.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the power-down bit is cleared, the chip internally triggers a
global reset. According to the KSZ9031 documentation, we have to wait at
least 1ms for the reset to finish.
If the chip is accessed during reset, read will return 0xffff, while
write will be ignored. Depending on the system performance and MDIO bus
speed, we may or may not run in to this issue.
This bug was discovered on an iMX6QP system with KSZ9031 PHY and
attached PHY interrupt line. If IRQ was used, the link status update was
lost. In polling mode, the link status update was always correct.
The investigation showed, that during a read-modify-write access, the
read returned 0xffff (while the chip was still in reset) and
corresponding write hit the chip _after_ reset and triggered (due to the
0xffff) another reset in an undocumented bit (register 0x1f, bit 1),
resulting in the next write being lost due to the new reset cycle.
This patch fixes the issue by adding a 1...2 ms sleep after the
genphy_resume().
Fixes: 836384d2501d ("net: phy: micrel: Add specific suspend") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct can_frame contains some padding which is not explicitly zeroed in
slc_bump. This uninitialized data will then be transmitted if the stack
initialization hardening feature is not enabled (CONFIG_INIT_STACK_ALL).
This commit just zeroes the whole struct including the padding.
Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com> Fixes: a1044e36e457 ("can: add slcan driver for serial/USB-serial CAN adapters") Reviewed-by: Kees Cook <keescook@chromium.org> Cc: linux-can@vger.kernel.org Cc: netdev@vger.kernel.org Cc: security@kernel.org Cc: wg@grandegger.com Cc: mkl@pengutronix.de Cc: davem@davemloft.net Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9463c4455900 ("net: stmmac: dwmac1000: Clear unused address
entries") cleared the unused mac address entries, but introduced an
out-of bounds mac address register programming bug -- After setting
the secondary unicast mac addresses, the "reg" value has reached
netdev_uc_count() + 1, thus we should only clear address entries
if (addr < perfect_addr_number)
Fixes: 9463c4455900 ("net: stmmac: dwmac1000: Clear unused address entries") Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the bcm_sf2 was converted into a proper platform device driver and
used the new dsa_register_switch() interface, we would still be parsing
the legacy DSA node that contained all the port information since the
platform firmware has intentionally maintained backward and forward
compatibility to client programs. Ensure that we do parse the correct
node, which is "ports" per the revised DSA binding.
Fixes: d9338023fb8e ("net: dsa: bcm_sf2: Make it a real platform device driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
======================================================
WARNING: possible circular locking dependency detected
5.4.0-rc8-padata-cpuhp-v3+ #1 Not tainted
------------------------------------------------------
bash/205 is trying to acquire lock: ffffffff8286bcd0 (cpu_hotplug_lock.rw_sem){++++}, at: padata_set_cpumask+0x2b/0x120
but task is already holding lock: ffff8880001abfa0 (&pinst->lock){+.+.}, at: padata_set_cpumask+0x26/0x120
which lock already depends on the new lock.
padata doesn't take cpu_hotplug_lock and pinst->lock in a consistent
order. Which should be first? CPU hotplug calls into padata with
cpu_hotplug_lock already held, so it should have priority.
Fixes: 6751fb3c0e0c ("padata: Use get_online_cpus/put_online_cpus") Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com> Cc: Eric Biggers <ebiggers@kernel.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: linux-crypto@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the backport of upstream commit 0e62f543bed03a64495bd2651d4fe1aa4bcb7fe5 ("net: dsa: Fix duplicate
frames flooded by learning") was done the assignment of
skb->fwd_offload_mark would land in brcm_tag_xmit() which is incorrect,
it should have been in brcm_tag_rcv().
The BIT() macro definition is not available for the UAPI headers
(moreover, it can be defined differently in the user space); replace
its usage with the _BITUL() macro that is defined in <linux/const.h>.
A recent commit runs tag iterator callbacks under the rcu read lock,
but existing callbacks do not satisfy the non-blocking requirement.
The commit intended to prevent an iterator from accessing a queue that's
being modified. This patch fixes the original issue by taking a queue
reference instead of reading it, which allows callbacks to make blocking
calls.
Fixes: f5bbbbe4d6357 ("blk-mq: sync the update nr_hw_queues with blk_mq_queue_tag_busy_iter") Acked-by: Jianchao Wang <jianchao.w.wang@oracle.com> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Giuliano Procida <gprocida@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For blk-mq, part_in_flight/rw will invoke blk_mq_in_flight/rw to
account the inflight requests. It will access the queue_hw_ctx and
nr_hw_queues w/o any protection. When updating nr_hw_queues and
blk_mq_in_flight/rw occur concurrently, panic comes up.
Before update nr_hw_queues, the q will be frozen. So we could use
q_usage_counter to avoid the race. percpu_ref_is_zero is used here
so that we will not miss any in-flight request. The access to
nr_hw_queues and queue_hw_ctx in blk_mq_queue_tag_busy_iter are
under rcu critical section, __blk_mq_update_nr_hw_queues could use
synchronize_rcu to ensure the zeroed q_usage_counter to be globally
visible.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Cc: Giuliano Procida <gprocida@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a MMU is shared between multiple GPUs, all of them need to flush their
TLBs, so a single marker that gets reset on the first flush won't do.
Replace the flush marker with a sequence number, so that it's possible to
check if the TLB is in sync with the current page table state for each GPU.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Guido Günther <agx@sigxcpu.org> Signed-off-by: Robert Beckett <bob.beckett@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under certain circumstances, depending on the order of addresses on the
interfaces, it could be that sctp_v[46]_get_dst() would return a dst
with a mismatched struct flowi.
For example, if when walking through the bind addresses and the first
one is not a match, it saves the dst as a fallback (added in 410f03831c07), but not the flowi. Then if the next one is also not a
match, the previous dst will be returned but with the flowi information
for the 2nd address, which is wrong.
The fix is to use a locally stored flowi that can be used for such
attempts, and copy it to the parameter only in case it is a possible
match, together with the corresponding dst entry.
The patch updates IPv6 code mostly just to be in sync. Even though the issue
is also present there, it fallback is not expected to work with IPv6.
Fixes: 410f03831c07 ("sctp: add routing output fallback") Reported-by: Jin Meng <meng.a.jin@nokia-sbell.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Tested-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should iterate over the datamsgs to move
all chunks(skbs) to newsk.
The following case cause the bug:
for the trouble SKB, it was in outq->transmitted list
sctp_outq_sack
sctp_check_transmitted
SKB was moved to outq->sacked list
then throw away the sack queue
SKB was deleted from outq->sacked
(but it was held by datamsg at sctp_datamsg_to_asoc
So, sctp_wfree was not called here)
then migrate happened
sctp_for_each_tx_datachunk(
sctp_clear_owner_w);
sctp_assoc_migrate();
sctp_for_each_tx_datachunk(
sctp_set_owner_w);
SKB was not in the outq, and was not changed to newsk
finally
__sctp_outq_teardown
sctp_chunk_put (for another skb)
sctp_datamsg_put
__kfree_skb(msg->frag_list)
sctp_wfree (for SKB)
SKB->sk was still oldsk (skb->sk != asoc->base.sk).
Reported-and-tested-by: syzbot+cea71eec5d6de256d54d@syzkaller.appspotmail.com Signed-off-by: Qiujun Huang <hqjagain@gmail.com> Acked-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when creating a new ipip interface with no local/remote configuration,
the lookup is done with TUNNEL_NO_KEY flag, making it impossible to
match the new interface (only possible match being fallback or metada
case interface); e.g: `ip link add tunl1 type ipip dev eth0`
To fix this case, adding a flag check before the key comparison so we
permit to match an interface with no local/remote config; it also avoids
breaking possible userland tools relying on TUNNEL_NO_KEY flag and
uninitialised key.
context being on my side, I'm creating an extra ipip interface attached
to the physical one, and moving it to a dedicated namespace.
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Signed-off-by: William Dauchy <w.dauchy@criteo.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix it by adding a pair of rcu_read_lock/unlock() and use
cond_resched_rcu() to avoid the situation where walking of a large
number of items may prevent scheduling for a long time.
Signed-off-by: Qian Cai <cai@lca.pw> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shutdown of firmware framebuffer has a bunch of problems. Because
of this the framebuffer region might still be reserved even after
drm_fb_helper_remove_conflicting_pci_framebuffers() returned.
Don't consider pci_request_region() failure for the framebuffer
region as fatal error to workaround this issue.
* deleting a session explicitly using the netlink interface (with
L2TP_CMD_SESSION_DELETE),
* deleting the session's parent tunnel (either by closing the
tunnel's file descriptor or using the netlink interface),
* closing the PPPOL2TP file descriptor of a PPP pseudo-wire.
In some cases, when these methods are used concurrently on the same
session, the session can be removed twice, leading to use-after-free
bugs.
This patch adds a 'dead' flag, used by l2tp_session_delete() and
l2tp_tunnel_closeall() to prevent them from stepping on each other's
toes.
The session deletion path used when closing a PPPOL2TP file descriptor
doesn't need to be adapted. It already has to ensure that a session
remains valid for the lifetime of its PPPOL2TP file descriptor.
So it takes an extra reference on the session in the ->session_close()
callback (pppol2tp_session_close()), which is eventually dropped
in the ->sk_destruct() callback of the PPPOL2TP socket
(pppol2tp_session_destruct()).
Still, __l2tp_session_unhash() and l2tp_session_queue_purge() can be
called twice and even concurrently for a given session, but thanks to
proper locking and re-initialisation of list fields, this is not an
issue.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If l2tp_tunnel_delete() or l2tp_tunnel_closeall() deletes a session
right after pppol2tp_release() orphaned its socket, then the 'sock'
variable of the pppol2tp_session_close() callback is NULL. Yet the
session is still used by pppol2tp_release().
Therefore we need to take an extra reference in any case, to prevent
l2tp_tunnel_delete() or l2tp_tunnel_closeall() from freeing the session.
Since the pppol2tp_session_close() callback is only set if the session
is associated to a PPPOL2TP socket and that both l2tp_tunnel_delete()
and l2tp_tunnel_closeall() hold the PPPOL2TP socket before calling
pppol2tp_session_close(), we're sure that pppol2tp_session_close() and
pppol2tp_session_destruct() are paired and called in the right order.
So the reference taken by the former will be released by the later.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an off-by-one error in strncpy size argument in
tools/perf/util/map.c. The issue is that in:
strncmp(filename, "/system/lib/", 11)
the passed string literal: "/system/lib/" has 12 bytes (without the NULL
byte) and the passed size argument is 11. As a result, the logic won't
match the ending "/" byte and will pass filepaths that are stored in
other directories e.g. "/system/libmalicious/bin" or just
"/system/libmalicious".
This functionality seems to be present only on Android. I assume the
/system/ directory is only writable by the root user, so I don't think
this bug has much (or any) security impact.
Fixes: eca818369996 ("perf tools: Add automatic remapping of Android libraries") Signed-off-by: disconnect3d <dominik.b.czarnota@gmail.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Changbin Du <changbin.du@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: John Keeping <john@metanate.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Lentine <mlentine@google.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Cc: Stephane Eranian <eranian@google.com> Link: http://lore.kernel.org/lkml/20200309104855.3775-1-dominik.b.czarnota@gmail.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building an arm64 defconfig with clang's integrated assembler, this error
occurs:
<instantiation>:2:2: error: unrecognized instruction mnemonic
_ASM_EXTABLE 9999b, 9f
^
arch/arm64/mm/cache.S:50:1: note: while in macro instantiation
user_alt 9f, "dc cvau, x4", "dc civac, x4", 0
^
While GNU as seems fine with case-sensitive macro instantiations, clang
doesn't, so use the actual macro name (_asm_extable) as in the rest of
the file.
Also checked that the generated assembly matches the GCC output.
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Fixes: 290622efc76e ("arm64: fix "dc cvau" cache operation on errata-affected core") Link: https://github.com/ClangBuiltLinux/linux/issues/924 Signed-off-by: Ilie Halip <ilie.halip@gmail.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverts 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation")
and edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access"), because it
turns out these were only necessary due to buggy hardware. This patch adds
a check for such a buggy hardware to prevent any such mistakes again.
While working further on the KS8851 driver, it came to light that the
KS8851-16MLL is capable of switching bus endianness by a hardware strap,
EESK pin. If this strap is incorrect, the IO accesses require such endian
swapping as is being reverted by this patch. Such swapping also impacts
the performance significantly.
Hence, in addition to removing it, detect that the hardware is broken,
report to user, and fail to bind with such hardware.
Fixes: 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation") Fixes: edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access") Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the bpf syscall, we are relying on the compiler to properly zero out
the bpf_attr union that we copy userspace data into. Unfortunately that
doesn't always work properly, padding and other oddities might not be
correctly zeroed, and in some tests odd things have been found when the
stack is pre-initialized to other values.
Fix this by explicitly memsetting the structure to 0 before using it.
Reported-by: Maciej Żenczykowski <maze@google.com> Reported-by: John Stultz <john.stultz@linaro.org> Reported-by: Alexander Potapenko <glider@google.com> Reported-by: Alistair Delva <adelva@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Yonghong Song <yhs@fb.com> Link: https://android-review.googlesource.com/c/kernel/common/+/1235490 Link: https://lore.kernel.org/bpf/20200320094813.GA421650@kroah.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vt_in_use() dereferences console_driver->ttys[i] without proper locking.
This is broken because the tty can be closed and freed concurrently.
We could fix this by using 'READ_ONCE(console_driver->ttys[i]) != NULL'
and skipping the check of tty_struct::count. But, looking at
console_driver->ttys[i] isn't really appropriate anyway because even if
it is NULL the tty can still be in the process of being closed.
Instead, fix it by making vt_in_use() require console_lock() and check
whether the vt is allocated and has port refcount > 1. This works since
following the patch "vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use
virtual console" the port refcount is incremented while the vt is open.
Reproducer (very unreliable, but it worked for me after a few minutes):
#include <fcntl.h>
#include <linux/vt.h>
int main()
{
int fd, nproc;
struct vt_stat state;
char ttyname[16];
BUG: KASAN: use-after-free in vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline]
BUG: KASAN: use-after-free in vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657
Read of size 4 at addr ffff888065722468 by task syz-vt2/132
Fixes: 4001d7b7fc27 ("vt: push down the tty lock so we can see what is left to tackle") Cc: <stable@vger.kernel.org> # v3.4+ Acked-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Eric Biggers <ebiggers@google.com> Link: https://lore.kernel.org/r/20200322034305.210082-3-ebiggers@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VT_DISALLOCATE ioctl can free a virtual console while tty_release()
is still running, causing a use-after-free in con_shutdown(). This
occurs because VT_DISALLOCATE considers a virtual console's
'struct vc_data' to be unused as soon as the corresponding tty's
refcount hits 0. But actually it may be still being closed.
Fix this by making vc_data be reference-counted via the embedded
'struct tty_port'. A newly allocated virtual console has refcount 1.
Opening it for the first time increments the refcount to 2. Closing it
for the last time decrements the refcount (in tty_operations::cleanup()
so that it happens late enough), as does VT_DISALLOCATE.
int main()
{
if (fork()) {
for (;;)
close(open("/dev/tty5", O_RDWR));
} else {
int fd = open("/dev/tty10", O_RDWR);
for (;;)
ioctl(fd, VT_DISALLOCATE, 5);
}
}
KASAN report:
BUG: KASAN: use-after-free in con_shutdown+0x76/0x80 drivers/tty/vt/vt.c:3278
Write of size 8 at addr ffff88806a4ec108 by task syz_vt/129
Fixes: 4001d7b7fc27 ("vt: push down the tty lock so we can see what is left to tackle") Cc: <stable@vger.kernel.org> # v3.4+ Reported-by: syzbot+522643ab5729b0421998@syzkaller.appspotmail.com Acked-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Eric Biggers <ebiggers@google.com> Link: https://lore.kernel.org/r/20200322034305.210082-2-ebiggers@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vc_cons_allocated() checks in vt_ioctl() and vt_compat_ioctl() are
unnecessary because they can only be reached by calling ioctl() on an
open tty, which implies the corresponding virtual console is allocated.
And even if the virtual console *could* be freed concurrently, then
these checks would be broken since they aren't done under console_lock,
and the vc_data is dereferenced before them anyway.
So, remove these unneeded checks to avoid confusion.
Avoid global variables (namely sel_cons) by introducing vc_is_sel. It
checks whether the parameter is the current selection console. This will
help putting sel_cons to a struct later.
The original patch didn't copy the ieee80211_is_data() condition
because on most drivers the management frames don't go through
this path. However, they do on iwlwifi/mvm, so we do need to keep
the condition here.
Cc: stable@vger.kernel.org Fixes: ce2e1ca70307 ("mac80211: Check port authorization in the ieee80211_tx_dequeue() case") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Woody Suwalski <terraluna977@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mac80211 used to check port authorization in the Data frame enqueue case
when going through start_xmit(). However, that authorization status may
change while the frame is waiting in a queue. Add a similar check in the
dequeue case to avoid sending previously accepted frames after
authorization change. This provides additional protection against
potential leaking of frames after a station has been disconnected and
the keys for it are being removed.
Make sure to check that we have two alternate settings and at least one
endpoint before accessing the second altsetting structure and
dereferencing the endpoint arrays.
This specifically avoids dereferencing NULL-pointers or corrupting
memory when a device does not have the expected descriptors.
Note that the sanity check in cit_get_packet_size() is not redundant as
the driver is mixing looking up altsettings by index and by number,
which may not coincide.
Fixes: 659fefa0eb17 ("V4L/DVB: gspca_xirlink_cit: Add support for camera with a bcd version of 0.01") Fixes: 59f8b0bf3c12 ("V4L/DVB: gspca_xirlink_cit: support bandwidth changing for devices with 1 alt setting") Cc: stable <stable@vger.kernel.org> # 2.6.37 Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check that we have two alternate settings and at least one
endpoint before accessing the second altsetting structure and
dereferencing the endpoint arrays.
This specifically avoids dereferencing NULL-pointers or corrupting
memory when a device does not have the expected descriptors.
Note that the sanity checks in stv06xx_start() and pb0100_start() are
not redundant as the driver is mixing looking up altsettings by index
and by number, which may not coincide.
Fixes: 8668d504d72c ("V4L/DVB (12082): gspca_stv06xx: Add support for st6422 bridge and sensor") Fixes: c0b33bdc5b8d ("[media] gspca-stv06xx: support bandwidth changing") Cc: stable <stable@vger.kernel.org> # 2.6.31 Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reading from a debugfs file at a nonzero position, without first reading
at position 0, leaks uninitialized memory to userspace.
It's a bit tricky to do this, since lseek() and pread() aren't allowed
on these files, and write() doesn't update the position on them. But
writing to them with splice() *does* update the position:
#define _GNU_SOURCE 1
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
int main()
{
int pipes[2], fd, n, i;
char buf[32];
pipe(pipes);
write(pipes[1], "0", 1);
fd = open("/sys/kernel/debug/fault_around_bytes", O_RDWR);
splice(pipes[0], NULL, fd, NULL, 1, 0);
n = read(fd, buf, sizeof(buf));
for (i = 0; i < n; i++)
printf("%02x", buf[i]);
printf("\n");
}
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging on
various user requests due to a malfunctioning (or malicious) device
until the device is physically disconnected.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: f3d27f34fdd7 ("[media] usbtv: Add driver for Fushicai USBTV007 video frame grabber") Fixes: c53a846c48f2 ("[media] usbtv: add video controls") Cc: stable <stable@vger.kernel.org> # 3.11 Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Lubomir Rintel <lkundrak@v3.sk> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b976fc6d684 ("media: b2c2-flexcop-usb: add sanity checking") added
an endpoint sanity check to address a NULL-pointer dereference on probe.
Unfortunately the check was done on the current altsetting which was later
changed.
Fix this by moving the sanity check to after the altsetting is changed.
Fixes: 1b976fc6d684 ("media: b2c2-flexcop-usb: add sanity checking") Cc: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handling a PIO bulk transfer with highmem buffer, a temporary
mapping is assigned to urb->transfer_buffer. After the transfer is
complete, an invalid address is left behind in this pointer. This is
not ordinarily a problem since nothing touches that buffer before the
urb is released. However, when usbmon is active, usbmon_urb_complete()
calls (indirectly) mon_bin_get_data() which does access the transfer
buffer if it is set. To prevent an invalid memory access here, reset
urb->transfer_buffer to NULL when finished (musb_host_rx()), or do not
set it at all (musb_host_tx()).
Fixes: 8e8a55165469 ("usb: musb: host: Handle highmem in PIO mode") Signed-off-by: Mans Rullgard <mans@mansr.com> Cc: stable@vger.kernel.org Signed-off-by: Bin Liu <b-liu@ti.com> Link: https://lore.kernel.org/r/20200316211136.2274-8-b-liu@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b401f8c4f492c ("USB: cdc-acm: fix rounding error in TIOCSSERIAL")
introduced a regression by changing the order of capability and close
settings change checks. When running with CAP_SYS_ADMIN setting the
close settings to the values already set resulted in -EOPNOTSUPP.
Fix this by changing the check order back to how it was before.
Fixes: b401f8c4f492c ("USB: cdc-acm: fix rounding error in TIOCSSERIAL") Cc: Anthony Mallet <anthony.mallet@laas.fr> Cc: stable <stable@vger.kernel.org> Cc: Oliver Neukum <oneukum@suse.com> Signed-off-by: Matthias Reichl <hias@horus.com> Link: https://lore.kernel.org/r/20200327150350.3657-1-hias@horus.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The O= directory existence check failed because the check script ran in
the build target directory instead of the directory where I ran the make
command.
To fix that, once change directory to $(PWD) and check O= directory,
since the PWD is set to where the make command runs.
Fixes: c883122acc0d ("perf tools: Let O= makes handle relative paths") Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Masahiro Yamada <masahiroy@kernel.org> Cc: Michal Marek <michal.lkml@markovi.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sasha Levin <sashal@kernel.org> Cc: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: stable@vger.kernel.org Link: http://lore.kernel.org/lkml/158351957799.3363.15269768530697526765.stgit@devnote2 Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
These functions are supposed to return negative error codes but instead
it returns true on failure and false on success. The error codes are
eventually propagated back to user space.
projects / thirdparty / kernel / stable.git / log
