wifi: ath12k: Advertise encapsulation/decapsulation offload support to mac80211
Currently, the mac80211 layer handles construction and parsing
of 802.11 headers during packet transmission and reception.
Offloading encapsulation and decapsulation to hardware can
significantly enhance performance. Check the service bit to determine
if the firmware supports Ethernet offload. If supported, advertise the
capability to mac80211 to bypass software-based 802.11 header
processing.
wifi: ath12k: Fix TX status reporting to mac80211 when offload is enabled
Currently, the ath12k driver supports only the native Wi-Fi
frame format. In this mode, the ieee80211_tx_status() function
works correctly to report transmission status to mac80211, as
it retrieves station information using sta_info_get_by_addrs().
However, this method is not applicable for Ethernet-converted
packets, since sta_info_get_by_addrs() cannot extract station
information from such formats.
Retrieve station information using ath12k_peer_find_by_id() to
support all frame formats, including native Wi-Fi, raw, and Ethernet.
Report transmission status using ieee80211_tx_status_ext(), and
include rate information as part of the datapath TX status report.
wifi: ath12k: Fix the handling of TX packets in Ethernet mode
Currently, in the transmit (TX) direction, EAPOL, QoS NULL,
and multicast frames are sent in native Wi-Fi (802.11) format.
However, when the virtual interface is configured in Ethernet
mode, transmission fails for packets enqueued in native Wi-fi format.
To address this issue, the firmware should be instructed to
treat these packets as RAW type packets, ensuring proper
handling even when the interface operates in Ethernet mode.
wifi: ath12k: Add support to parse max ext2 wmi service bit
Update the host logic to dynamically parse WMI extended service
bits beyond the current fixed size of 4 * 32 (i.e., 384 bits)
after WMI_MAX_EXT_SERVICE (256).
The current implementation misses service bits advertised beyond this
range, leading to not enabling some of the features supported by firmware.
Implement dynamic length parsing to iterate up to the maximum
service bit index advertised by the firmware.
This ensures all supported features are correctly recognized and enabled.
wifi: ath12k: fix endianness handling while accessing wmi service bit
Currently there is no endian conversion in ath12k_wmi_tlv_services_parser()
so the service bit parsing will be incorrect on a big endian platform and
to fix this by using appropriate endian conversion.
Fixes: 342527f35338 ("wifi: ath12k: Add support to parse new WMI event for 6 GHz regulatory") Signed-off-by: Tamizh Chelvam Raja <tamizh.raja@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250717173539.2523396-2-tamizh.raja@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Baochen Qiang [Tue, 3 Jun 2025 02:25:28 +0000 (10:25 +0800)]
wifi: ath11k: fix sleeping-in-atomic in ath11k_mac_op_set_bitrate_mask()
ath11k_mac_disable_peer_fixed_rate() is passed as the iterator to
ieee80211_iterate_stations_atomic(). Note in this case the iterator is
required to be atomic, however ath11k_mac_disable_peer_fixed_rate() does
not follow it as it might sleep. Consequently below warning is seen:
BUG: sleeping function called from invalid context at wmi.c:304
Call Trace:
<TASK>
dump_stack_lvl
__might_resched.cold
ath11k_wmi_cmd_send
ath11k_wmi_set_peer_param
ath11k_mac_disable_peer_fixed_rate
ieee80211_iterate_stations_atomic
ath11k_mac_op_set_bitrate_mask.cold
Change to ieee80211_iterate_stations_mtx() to fix this issue.
Sriram R [Mon, 14 Jul 2025 11:14:38 +0000 (16:44 +0530)]
wifi: ath12k: Validate peer_id before searching for peer
In RX WBM error path, error packet is received with invalid
peer_id (0x3FFF) as there is no peer associated with that packet.
However, this invalid peer_id coincides with the ML peer_id valid
bit mask, causing an unnecessary search in the ML peer list.
Prevent searching the peer list for invalid peer_id and return NULL.
wifi: ath12k: Use HTT_TCL_METADATA_VER_V1 in FTM mode
Currently host sends HTT_TCL_METADATA_VER_V2 to the firmware
regardless of the operating mode (Mission or FTM).
Firmware expects additional software information (like peer ID, vdev
ID, and link ID) in Tx packets when HTT_TCL_METADATA_VER_V2 is set.
However, in FTM (Factory Test Mode) mode, no vdev is created on the
host side (this is expected). As a result, the firmware fails to find
the expected vdev during packet processing and ends up dropping
packets.
To fix this, send HTT_TCL_METADATA_VER_V1 in FTM mode because FTM
mode doesn't support HTT_TCL_METADATA_VER_V2.
Fixes: 5d964966bd3f ("wifi: ath12k: Update HTT_TCL_METADATA version and bit mask definitions") Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250711035420.1509029-1-aaradhana.sahu@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Sriram R [Fri, 11 Jul 2025 09:17:04 +0000 (14:47 +0530)]
wifi: ath12k: Add support to enqueue management frame at MLD level
A multi-link client can use any link for transmissions. It can decide to
put one link in power save mode for longer periods while listening on the
other links as per MLD listen interval. Unicast management frames sent to
that link station might get dropped if that link station is in power save
mode or inactive. In such cases, firmware can take decision on which link
to use.
Allow the firmware to decide on which link management frame should be
sent on, by filling the hardware link with maximum value of u32, so that
the firmware will not have a specific link to transmit data on and so
the management frames will be link agnostic. For QCN devices, all action
frames are marked as link agnostic. For WCN devices, if the device is
configured as an AP, then all frames other than probe response frames,
authentication frames, association response frames, re-association response
frames and ADDBA response frames are marked as link agnostic and if the
device is configured as a station, then all frames other than probe request
frames, authentication frames, de-authentication frames and ADDBA response
frames are marked as link agnostic.
wifi: ath12k: Enable memory profile selection for QCN9274
The QCN9274 supports two memory profiles: a default profile and a
low-memory profile. The driver signals the firmware to enable
low-memory optimizations using the QMI initialization service.
Add support to select the low-memory profile on system with less than
512 MB RAM.
wifi: ath12k: Remove redundant TID calculation for QCN9274
Currently, host sends num_tids (number of TID (Traffic Identifier))
value to firmware via WMI_INIT_CMD during WMI initialization. However,
the firmware does not use this value, as it determines the number of
TIDs using its own internal logic.
Hence, remove the redundant num_tids calculation logic for QCN9274.
wifi: ath12k: Add a table of parameters entries impacting memory consumption
Introduce ath12k_mem_profile_based_param structure to define
configuration parameters for both default and low-memory profiles.
Add support for enabling the low-memory profile in the follow-up
patch by making the following changes:
- Reduce sizes for transmit, receive, and monitor descriptor rings.
- Reduce transmit and receive descriptor count.
- Limit the maximum number of virtual devices (vdevs) to 9.
- Reduce the maximum number of client support per radio.
Centralize these parameters in the ath12k_mem_profile_based_param
structure to simplify switching between memory profiles.
wifi: ath12k: support average ack rssi in station dump
Currently, the ACK RSSI value is not shown in station dump. Enable WMI
resource flag for ACK RSSI in WMI INIT command to add ACK RSSI value in
management TX completion event from WMI. Update ACK RSSI value obtained
in management and data frame completion path to ieee80211_tx_info. Also
advertise NL80211_EXT_FEATURE_ACK_SIGNAL_SUPPORT flag during hardware
register to mac80211 layer so that ACK RSSI is added to station dump
message.
Example output :
Station aa:bb:cc:dd:ee:ff (on wlp88s0)
inactive time: 46584 ms
rx bytes: 955
rx packets: 10
tx bytes: 769
tx packets: 6
tx retries: 81
tx failed: 0
rx drop misc: 0
signal: -39 dBm
signal avg: -40 dBm
tx bitrate: 6.0 MBit/s
tx duration: 1185 us
rx bitrate: 309.7 MBit/s 40MHz HE-MCS 6 HE-NSS 2 HE-GI 0 HE-DCM 0
rx duration: 0 us
last ack signal:-41 dBm
avg ack signal: -40 dBm
authorized: yes
authenticated: yes
.......
wifi: ath12k: allow beacon protection keys to be installed in hardware
Install beacon protection keys in hardware for AP modes only if hardware
supports it, as indicated by the WMI service bit
WMI_TLV_SERVICE_BEACON_PROTECTION_SUPPORT. Allow keyidx up to 7, since
beacon protection uses keyidx 6 and 7.
Control this feature by setting bit 0 of feature_enable_bitmap when sending
the WMI_BCN_TMPL_CMDID command to firmware.
Check for the beacon protection enabled bit in both tx and non-tx profiles
for MBSSID cases. If set in either profile, enable the beacon protection
feature in firmware for transmitted vif.
P Praneesh [Thu, 5 Jun 2025 05:01:35 +0000 (10:31 +0530)]
wifi: ath12k: set RX_FLAG_SKIP_MONITOR in WBM error path
Packets delivered to mac80211 from the WBM error path currently do not
have the RX_FLAG_SKIP_MONITOR flag set in status->flag. As a result,
mac80211 performs unnecessary monitor mode checks on each packet, even
though these packets are not intended for monitor mode processing.
In regular rx path, this flag is explicitly set to avoid such overhead.
Align the WBM error path behavior by setting RX_FLAG_SKIP_MONITOR to
prevent redundant per-packet checks in mac80211.
Jeff Johnson [Wed, 2 Jul 2025 21:29:12 +0000 (14:29 -0700)]
wifi: ath12k: pack HTT pdev rate stats structs
In order to ensure the HTT DebugFS structs shared with firmware have
matching alignment, the structs should be packed. Most of the structs
are correctly packed, however the following are not:
wifi: ath12k: update unsupported bandwidth flags in reg rules
The maximum bandwidth an interface can operate in is defined by the
configured country. However, currently, it is able to operate in
bandwidths greater than the allowed bandwidth. For example,
the Central African Republic (CF) supports a maximum bandwidth of 40 MHz
in both the 2 GHz and 5 GHz bands, but an interface is still able to
operate in bandwidths higher than 40 MHz. This issue arises because the
regulatory rules in the regd are not updated with these restrictions
received from firmware on the maximum bandwidth.
Hence, update the regulatory rules with unsupported bandwidth flags based
on the maximum bandwidth to ensure compliance with country-specific
regulations.
wifi: ath12k: Add num_stations counter for each interface
Currently, ath12k driver maintains a counter to store the number of
stations connected to each radio. However, at certain times like
debugging, it is useful to know number of stations connected to any
one of the interface in that radio.
Add support to maintain a counter for number of stations connected to
each interface.
Sarika Sharma [Mon, 30 Jun 2025 06:44:31 +0000 (12:14 +0530)]
wifi: ath12k: properly set bit for pdev mask for firmware PPDU_STATS request
Currently, the HTT_H2T_MSG_TYPE_PPDU_STATS_CFG request uses bits
8 to 15 as the bitmask for HTT_PPDU_STATS_CFG_PDEV_ID for firmware
PPDU_STATS. However, bit 8 is reserved for SOC stats, and the actual
PDEV ID should be encoded using bits 9 to 15. This leads to incorrect
PDEV ID encoding in the request, causing it to either ignore the
request or apply it to the wrong PDEV.
Additionally, pdev_mask calculation is done as
pdev_mask = 1 << (i + 1); (i.e. i= num_rxmda_per_pdev)
but this is not valid for multiple pdevs(multi-MAC configurations)
with 1 rxdma per pdev, as this will mask the same value for all pdevs.
To correctly identify each and exact MAC in multi-MAC configurations,
the calculation should include ar->pdev_idx:
pdev_mask = 1 << i + ar->pdev_idx;
Due to these issues, the firmware does not send PPDU_STATS for the
intended PDEV, leading to inaccurate and incomplete statistics on the
host. This might trigger certain WARN_ON() conditions in host that
rely on these statistics.
Hence, change the bitmask for HTT_PPDU_STATS_CFG_PDEV_ID as bit 9
to 15 to properly fill the pdev id in request message and change
the pdev_mask calculation to consider ar->pdev_idx to mask pdev
correctly.
Aaradhana Sahu [Mon, 30 Jun 2025 03:15:02 +0000 (08:45 +0530)]
wifi: ath12k: Block radio bring-up in FTM mode
Ensure that all radios remain down when the driver operates in Factory
Test Mode (FTM). Reject any userspace attempts to bring up an
interface in this mode.
Currently, the driver allows userspace to bring up the interface even
though it operates in FTM mode, which violates FTM constraints and
leads to FTM command failures.
Hence, block the radio start when the driver is in FTM mode. Also,
remove ath12k_ftm_mode check from ath12k_drain_tx() because FTM mode
check is already handled in the caller function
(ath12k_mac_op_start()).
wifi: ath12k: add support for Tx Power insertion in RRM action frame
For certain action frames like the TPC Report IE in the spectrum management
TPC Report action frame, and in the Radio Measurement Link Measurement
Report action frame there is a requirement to fill in the current
and max Tx power of the device in the packet.
Add support to populate these fields in the relevant packets.
In software-encrypted cases such as PMF, skip insertion since the packets
are already encrypted and cannot be modified.
wifi: ath12k: fetch tx_retry and tx_failed from htt_ppdu_stats_user_cmpltn_common_tlv
Currently, tx_retries and tx_failed are updated only in mac80211 during
tx_completion path for sta->deflink. This works fine for non-ML
station but for multi-link (ML) station, these values should be updated
for sta->link[link_id] as per tx link_id. However, in tx_completion path
there is no way to determine the link_id for which packet is retried or
failed.
Therefore, update the tx_retries and tx_failed in arsta structure from
htt_ppdu_stats_user_cmpltn_common_tlv during
ath12k_update_per_peer_tx_stats() call to utilize the values from arsta.
Also, during 'iw dev xxxx station dump' populate the tx_retries and
tx_failed in station_info structure to ensure values are correctly
reflected.
wifi: ath12k: correctly update bw for ofdma packets
Currently, arsta->txrate.bw is filled from ath12k_mac_bw_to_mac80211_bw(bw)
during ath12k_update_per_peer_tx_stats(). But in tx_completion path bw
is filled differently if ppdu_type is ofdma for HE/EHT rates.
Hence, update arsta->txrate.bw correctly if packet is ofdma for HE
and EHT rate.
wifi: ath12k: add link support for multi-link in arsta
Currently, statistics in arsta are updated at deflink for both non-ML
and multi-link(ML) station. Link statistics are not updated for
multi-link operation(MLO).
Hence, add support to correctly obtain the link ID if the peer is ML,
fetch the arsta from the appropriate link ID, and update the
statistics in the corresponding arsta.
wifi: ath12k: fill link station statistics for MLO
Introduce ath12k_mac_op_link_sta_statistics(), to report link level
station statistics for MLO. The link_station_info structure is filled
from arsta and arsta is fetch from corresponding ahsta->link[link_id].
Therefore, this will be helpful to check the link related statistics.
wifi: ath12k: add extended NSS bandwidth support for 160 MHz
Currently rx and tx MCS map for 160 MHz under HE capabilities
are not updating properly, when 160 MHz is configured with NSS
lesser than max NSS support. Fix this by utilizing
nss_ratio_enabled and nss_ratio_info fields sent by firmware
in service ready event.
However, if firmware advertises EXT NSS BW support in VHT caps
as 1(1x2) and when nss_ratio_info indicates 1:1, reset the EXT
NSS BW Support in VHT caps to 0 which indicates 1x1. This is
to avoid incorrectly choosing 1:2 NSS ratio when using the
default VHT caps advertised by firmware.
Add support to configure maximum NSS in 160 MHz bandwidth.
Firmware advertises support for handling NSS ratio information
as a part of service ready ext event using nss_ratio_enabled
flag. Save this information in ath12k_pdev_cap to calculate
NSS ratio.
Additionally, reorder the code by moving
ath12k_peer_assoc_h_phymode() before ath12k_peer_assoc_h_vht()
to ensure that arg->peer_phymode correctly reflects the bandwidth
in the max NSS calculation.
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com> Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Link: https://patch.msgid.link/20250701010408.1257201-9-quic_pradeepc@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
wifi: ath12k: add support for setting fixed HE rate/GI/LTF
Add support to set fixed HE rate/GI/LTF values using nl80211.
Reuse parts of the existing code path already used for HT/VHT
to implement the new helpers symmetrically, similar to how
HT/VHT is handled.
wifi: ath12k: generate rx and tx mcs maps for supported HE mcs
Generate rx and tx mcs maps in ath12k_mac_set_hemcsmap() based
on number of supported tx/rx chains and set them in supported
mcs/nss for HE capabilities.
Currently, only the EHT IE in management frames is updated with
respect to MU-MIMO configurations, but this change is not
reflected in the hardware. Add support to propagate MU-MIMO
configurations to the hardware as well for AP mode. Similar
support for STA mode will be added in future.
Currently, only the HE IE in management frames is updated with
respect to MU-MIMO configurations, but this change is not
reflected in the hardware. Add support to propagate MU-MIMO
configurations to the hardware as well.
Kang Yang [Mon, 23 Jun 2025 02:27:31 +0000 (10:27 +0800)]
wifi: ath10k: shutdown driver when hardware is unreliable
In rare cases, ath10k may lose connection with the PCIe bus due to
some unknown reasons, which could further lead to system crashes during
resuming due to watchdog timeout:
At this point, all WMI commands will timeout and attempt to restart
device. So set a threshold for consecutive restart failures. If the
threshold is exceeded, consider the hardware is unreliable and all
ath10k operations should be skipped to avoid system crash.
fail_cont_count and pending_recovery are atomic variables, and
do not involve complex conditional logic. Therefore, even if recovery
check and reconfig complete are executed concurrently, the recovery
mechanism will not be broken.
wifi: ath12k: fix timeout while waiting for regulatory update during interface creation
During interface creation, following print is observed on the console -
Timeout while waiting for regulatory update
This occurs due to commit 906619a00967 ("wifi: ath12k: handle regulatory
hints during mac registration"), which introduced a completion mechanism to
synchronize the regulatory update process. The intent behind this change is
to coordinate the timing between when the firmware sends regulatory data to
the driver and when the driver processes that data.
However, during interface addition, if the 6 GHz band is active, the driver
invokes ath12k_regd_update() to apply the appropriate 6 GHz power mode
regulatory settings. At this point, there is no interaction with the
firmware, so the completion object is not reinitialized. As a result,
wait_for_completion() eventually times out, leading to the observed error
log message.
Hence to fix this, move all complete() on regd_update_completed to
complete_all().
The complete() function signals only once, causing any subsequent waits
without reinitialization to timeout. In this scenario, since waiting is
unnecessary, complete_all() can be used instead, ensuring that subsequent
calls to wait without reinitialization will simply bail out and not
actually wait. This approach is ideal because if the firmware is not
involved, there is no need to wait for the completion event. However, if
the firmware is involved, it is guaranteed that the completion will be
reinitialized, and thus, it would wait.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1 Tested-by: Kang Yang <kang.yang@oss.qualcomm.com>
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Add support to request RTT stats from firmware through HTT stats type 65
and 66. HTT stats type 65 support RTT response stats, RTT hardware stats,
RTT to-be-read self-generated stats and RTT command-result stats and HTT
stats type 66 support RTT initiator stats and RTT hardware stats. These
stats give information about number of scheduled commands, responder
allocation and termination count, initiator termination count, PASN
authentication drop and receive counts, etc.
Note: WCN firmware version -
WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 does not support
tags HTT_STATS_PDEV_RTT_RESP_STATS_TAG(194),
HTT_STATS_PDEV_RTT_INIT_STATS_TAG(195),
HTT_STATS_PDEV_RTT_HW_STATS_TAG(196),
HTT_STATS_PDEV_RTT_TBR_SELFGEN_QUEUED_STATS_TAG(197) and
HTT_STATS_PDEV_RTT_TBR_CMD_RESULT_STATS_TAG(198), currently.
HTT_STATS_PDEV_RTT_TBR_SELFGEN_QUEUED_STATS_TAG:
SU poll = 0
SU sound = 0
.....
MU poll = 0
MU sound = 0
.....
HTT_STATS_PDEV_RTT_TBR_CMD_RESULT_STATS_TAG:
num_sch_cmd_status_0:
SU frame_SGEN_TF_POLL = 0
SU frame_SGEN_TF_SOUND = 0
SU frame_SGEN_TBR_NDPA = 0
SU frame_SGEN_TBR_NDP = 0
SU frame_SGEN_TBR_LMR = 0
SU frame_SGEN_TF_REPORT = 0
MU frame_SGEN_TF_POLL = 0
.....
Add support to request TDMA stats, MLO scheduled stats and MLO IPC stats
from firmware through HTT stats type 57, 63 and 64, respectively. These
stats give information about TDMA schedules, TDMA slot switches, MLO
preferred timeout, delay, MLO IPC ring count, etc.
Note: WCN firmware version -
WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 does not support
tags HTT_STATS_PDEV_TDMA_TAG(187), HTT_STATS_MLO_SCHED_STATS_TAG(190)
and HTT_STATS_PDEV_MLO_IPC_STATS_TAG(191), currently.
wifi: ath12k: Add support for transmit histogram stats
Add support for transmit histogram stats under HTT stats type 9. These
stats give information about drop count, MCS drop rate, histogram
count, etc.
Note: WCN7850 firmware version -
WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 does not support tag
HTT_STATS_TX_PDEV_HISTOGRAM_STATS_TAG(144), currently.
wifi: ath12k: Clear auth flag only for actual association in security mode
When setting a new bitrate, WMI peer association command is sent from
the host without the peer authentication bit set in peer_flags for
security mode, which causes ping failure.
The firmware handles peer_flags when the client is associating, as the
peer authentication bit in peer_flags is set after the key exchange.
When the WMI peer association command is sent from the host to update
the new bitrate for an associated STA, the firmware expects the WMI
peer authentication bit to be set in peer_flags.
Fix this issue by ensuring that the WMI peer auth bit is set in
peer_flags in WMI peer association command when updating the new
bitrate.
Johan Hovold [Tue, 17 Jun 2025 08:44:02 +0000 (10:44 +0200)]
wifi: ath12k: fix dest ring-buffer corruption when ring is full
Add the missing memory barriers to make sure that destination ring
descriptors are read before updating the tail pointer (and passing
ownership to the device) to avoid memory corruption on weakly ordered
architectures like aarch64 when the ring is full.
Johan Hovold [Tue, 17 Jun 2025 08:44:01 +0000 (10:44 +0200)]
wifi: ath12k: fix source ring-buffer corruption
Add the missing memory barrier to make sure that LMAC source ring
descriptors are written before updating the head pointer to avoid
passing stale data to the firmware on weakly ordered architectures like
aarch64.
Note that non-LMAC rings use MMIO write accessors which have the
required write memory barrier.
Johan Hovold [Tue, 17 Jun 2025 08:44:00 +0000 (10:44 +0200)]
wifi: ath12k: use plain access for descriptor length
The read memory barrier added by commit 6b67d2cf14ea ("wifi: ath12k: fix
ring-buffer corruption") is enough to guarantee ordering also for plain
descriptor accesses if the length helper is ever inlined so drop the
unnecessary READ_ONCE().
Johan Hovold [Tue, 17 Jun 2025 08:43:59 +0000 (10:43 +0200)]
wifi: ath12k: fix dest ring-buffer corruption
Add the missing memory barrier to make sure that destination ring
descriptors are read after the head pointers to avoid using stale data
on weakly ordered architectures like aarch64.
The barrier is added to the ath12k_hal_srng_access_begin() helper for
symmetry with follow-on fixes for source ring buffer corruption which
will add barriers to ath12k_hal_srng_access_end().
Johan Hovold [Wed, 4 Jun 2025 14:34:57 +0000 (16:34 +0200)]
wifi: ath11k: fix dest ring-buffer corruption when ring is full
Add the missing memory barriers to make sure that destination ring
descriptors are read before updating the tail pointer (and passing
ownership to the device) to avoid memory corruption on weakly ordered
architectures like aarch64 when the ring is full.
Johan Hovold [Wed, 4 Jun 2025 14:34:56 +0000 (16:34 +0200)]
wifi: ath11k: fix source ring-buffer corruption
Add the missing memory barrier to make sure that LMAC source ring
descriptors are written before updating the head pointer to avoid
passing stale data to the firmware on weakly ordered architectures like
aarch64.
Note that non-LMAC rings use MMIO write accessors which have the
required write memory barrier.
Johan Hovold [Wed, 4 Jun 2025 14:34:55 +0000 (16:34 +0200)]
wifi: ath11k: use plain accesses for monitor descriptor
The read memory barrier added by commit ab52e3e44fe9 ("wifi: ath11k: fix
rx completion meta data corruption") is enough to guarantee ordering
also for plain descriptor accesses so drop the unnecessary READ_ONCE().
Johan Hovold [Wed, 4 Jun 2025 14:34:54 +0000 (16:34 +0200)]
wifi: ath11k: use plain access for descriptor length
The read memory barrier added by commit 6d037a372f81 ("wifi: ath11k: fix
ring-buffer corruption") is enough to guarantee ordering also for plain
descriptor accesses if the length helper is ever inlined so drop the
unnecessary READ_ONCE().
Johan Hovold [Wed, 4 Jun 2025 14:34:53 +0000 (16:34 +0200)]
wifi: ath11k: fix dest ring-buffer corruption
Add the missing memory barrier to make sure that destination ring
descriptors are read after the head pointers to avoid using stale data
on weakly ordered architectures like aarch64.
The barrier is added to the ath11k_hal_srng_access_begin() helper for
symmetry with follow-on fixes for source ring buffer corruption which
will add barriers to ath11k_hal_srng_access_end().
wifi: ath12k: Send WMI_VDEV_SET_TPC_POWER_CMD for AP vdev
The power value is 6 dBm on an AP operating on the 6 GHz channel.
This is a very low value.
On 6 GHz, the target computes the EIRP based on the power values sent
in the WMI_VDEV_SET_TPC_POWER_CMD. Currently, this is being sent only
for station interfaces and not for AP interfaces.
Therefore, add AP vdev to the condition in
ath12k_mac_station_supports_tpc() and rename
ath12k_mac_station_supports_tpc() to ath12k_mac_supports_tpc().
For a AP vdev, hardcode ap_power_type as IEEE80211_REG_LPI_AP, which is
filled in the WMI_VDEV_SET_TPC_POWER_CMDID sent to the target.
Currently, LPI is the only supported AP power mode. Since there is
no method currently to set the AP power mode from user-space, the
power mode is hard-coded to LPI.
Retain the existing logic for populating the power mode for a station
vdev.
Sarika Sharma [Tue, 3 Jun 2025 06:35:12 +0000 (12:05 +0530)]
wifi: ath12k: Add memset and update default rate value in wmi tx completion
When both AP/STA and monitor interfaces are enabled, ieee80211_tx_status()
is invoked from two paths: the TX completion handler for data frames
and the WMI TX completion handler for management frames.
In the data path, the skb->cb is properly zeroed using memset, but in
the WMI path, this step is missing.
As a result, mac80211 encountered uninitialized (junk) values in
skb->cb when generating the radiotap header for monitor mode, leading
to invalid radiotap lengths.
Hence, explicitly zero the status field in the skb->cb using memset
in WMI TX completion path to ensure consistent and correct behavior
during WMI tx completion path.
Additionally, set info->status.rates[0].idx = -1 to indicate that
no valid rate information is available, avoiding misinterpretation of
garbage values.
wifi: ath12k: Fix beacon reception for sta associated to Non-TX AP
Currently, when a station is associated with a Non-Transmitting BSS of an
MBSSID set, beacons are not frequently received from the firmware. This
results in missing events via beacons, such as channel switches, leading
to the station not switching to new channel as the AP does, eventually
causing a kick out event from the firmware. This issue arises due to
missing configuration of Non-Transmitting BSS information in station's
vdev up command.
Fix this by filling information such as the Transmitting BSSID, profile index
and profile count in vdev up command of station.
wifi: ath12k: Fix station association with MBSSID Non-TX BSS
ath12k station is unable to associate with non-transmitting BSSes
in a Multiple BSS set because the user-space does not receive
information about the non-transmitting BSSes from mac80211's
scan results.
The ath12k driver does not advertise its MBSSID capability to mac80211,
resulting in wiphy->support_mbssid not being set. Consequently, the
information about non-transmitting BSS is not parsed from received
Beacon/Probe response frames and is therefore not included in the
scan results.
Fix this by advertising the MBSSID capability of ath12k driver to
mac80211.
wifi: ath12k: use real noise floor instead of default value
ATH12K_DEFAULT_NOISE_FLOOR represents the approximate noise floor value
which is used for RSSI calculation. Commit "wifi: ath12k: handle WMI event
for real noise floor calculation" added support to get the real noise floor
value from the firmware. Add changes to use the real value now instead of
the default one.
wifi: ath12k: handle WMI event for real noise floor calculation
At present, the ATH12K_DEFAULT_NOISE_FLOOR (-95) is used to calculate RSSI
value, providing an estimated noise floor value. Consequently, the RSSI
value is also approximate. This works but however, using actual noise floor
value will enable the reporting of the true RSSI value.
The firmware possesses the necessary data to determine the actual noise
floor. This data is provided to the host via the WMI event
WMI_PDEV_RSSI_DBM_CONVERSION_PARAMS_INFO_EVENTID, which includes the
runtime parameters needed for calculating the real noise floor in dBm. This
event is triggered by the firmware during channel changes, temperature
offset adjustments, and hardware chainmask modifications. The individual
TLVs may not always be present in each event. For instance, temperature
information might only appear if there is a change in offset due to
temperature variation.
Add support to handle and parse this WMI event. Use the received values to
calculate and store the noise floor value.
A subsequent change will use this noise floor value in the actual RSSI
calculation.
wifi: ath11k: clear initialized flag for deinit-ed srng lists
In a number of cases we see kernel panics on resume due
to ath11k kernel page fault, which happens under the
following circumstances:
1) First ath11k_hal_dump_srng_stats() call
Last interrupt received for each group:
ath11k_pci 0000:01:00.0: group_id 0 22511ms before
ath11k_pci 0000:01:00.0: group_id 1 14440788ms before
[..]
ath11k_pci 0000:01:00.0: failed to receive control response completion, polling..
ath11k_pci 0000:01:00.0: Service connect timeout
ath11k_pci 0000:01:00.0: failed to connect to HTT: -110
ath11k_pci 0000:01:00.0: failed to start core: -110
ath11k_pci 0000:01:00.0: firmware crashed: MHI_CB_EE_RDDM
ath11k_pci 0000:01:00.0: already resetting count 2
ath11k_pci 0000:01:00.0: failed to wait wlan mode request (mode 4): -110
ath11k_pci 0000:01:00.0: qmi failed to send wlan mode off: -110
ath11k_pci 0000:01:00.0: failed to reconfigure driver on crash recovery
[..]
2) At this point reconfiguration fails (we have 2 resets) and
ath11k_core_reconfigure_on_crash() calls ath11k_hal_srng_deinit()
which destroys srng lists. However, it does not reset per-list
->initialized flag.
3) Second ath11k_hal_dump_srng_stats() call sees stale ->initialized
flag and attempts to dump srng stats:
Last interrupt received for each group:
ath11k_pci 0000:01:00.0: group_id 0 66785ms before
ath11k_pci 0000:01:00.0: group_id 1 14485062ms before
ath11k_pci 0000:01:00.0: group_id 2 14485062ms before
ath11k_pci 0000:01:00.0: group_id 3 14485062ms before
ath11k_pci 0000:01:00.0: group_id 4 14780845ms before
ath11k_pci 0000:01:00.0: group_id 5 14780845ms before
ath11k_pci 0000:01:00.0: group_id 6 14485062ms before
ath11k_pci 0000:01:00.0: group_id 7 66814ms before
ath11k_pci 0000:01:00.0: group_id 8 68997ms before
ath11k_pci 0000:01:00.0: group_id 9 67588ms before
ath11k_pci 0000:01:00.0: group_id 10 69511ms before
BUG: unable to handle page fault for address: ffffa007404eb010
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 100000067 P4D 100000067 PUD 10022d067 PMD 100b01067 PTE 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:ath11k_hal_dump_srng_stats+0x2b4/0x3b0 [ath11k]
Call Trace:
<TASK>
? __die_body+0xae/0xb0
? page_fault_oops+0x381/0x3e0
? exc_page_fault+0x69/0xa0
? asm_exc_page_fault+0x22/0x30
? ath11k_hal_dump_srng_stats+0x2b4/0x3b0 [ath11k (HASH:6cea 4)]
ath11k_qmi_driver_event_work+0xbd/0x1050 [ath11k (HASH:6cea 4)]
worker_thread+0x389/0x930
kthread+0x149/0x170
Clear per-list ->initialized flag in ath11k_hal_srng_deinit().
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org> Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com> Fixes: 5118935b1bc2 ("ath11k: dump SRNG stats during FW assert") Link: https://patch.msgid.link/20250612084551.702803-1-senozhatsky@chromium.org Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Miaoqing Pan [Thu, 22 May 2025 01:34:44 +0000 (09:34 +0800)]
wifi: ath11k: support usercase-specific firmware overrides
Introduce 'firmware-name' property to allow end-users and/or integrators to
decide which usecase-specific firmware to run on the WCN6855. This is
necessary due to resource limitations such as memory capacity and CPU
capability, or performance and power optimization for different application
scenarios.
Currently, there are two firmwares, both files can be executed
interchangeably.
For example:
The former is the default firmware, suitable for most WiFi 6 STA functions.
The latter adds support for commercial-quality SAP and optimizes power
consumption for IoT applications. And both use the same BDF/regdb data
within the main board-2.bin.
Introduce 'firmware-name' property to allow end-users and/or integrators
to decide which usecase-specific firmware to run on the WCN6855. This is
necessary due to resource limitations such as memory capacity and
CPU capability, or performance and power optimization for different
application scenarios.
Two firmwares are supported: 'WCN6855/hw2.0' and 'WCN6855/hw2.0/nfa765'.
The former is the default firmware, suitable for most WiFi 6 STA
functions. The latter adds support for commercial-quality SAP and
optimizes power consumption for IoT applications.
Rosen Penev [Mon, 9 Jun 2025 03:08:50 +0000 (20:08 -0700)]
wifi: ath9k: ahb: replace id_table with of
Since 2b0996c7646 , all of this platform code became no-op with no OF
replacement. Not only that, there are no users of AHB here. Add an OF
match table that mostly mirrors the original platform device id table.
Use a qca prefix as is done for the only other property: qca,no-eeprom.
Also used qca prefix for ar9530 as the latter seems to be a mistake.
This will be used to add ath9k support for the various ath79 devices
here.
Signed-off-by: Rosen Penev <rosenp@gmail.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Link: https://patch.msgid.link/20250609030851.17739-5-rosenp@gmail.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Rosen Penev [Mon, 9 Jun 2025 03:08:47 +0000 (20:08 -0700)]
wifi: ath9k: ahb: reorder declarations
Easier to look at. Follows netdev style.
Also remove ret assignment. Because of all of these devm conversions,
ret = 0 is a path that never gets hit. The first time it does it when
request_irq fails, but that ends up reassigning it.
Signed-off-by: Rosen Penev <rosenp@gmail.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Link: https://patch.msgid.link/20250609030851.17739-2-rosenp@gmail.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Cross-merge networking fixes after downstream PR (net-6.16-rc4).
Conflicts:
Documentation/netlink/specs/mptcp_pm.yaml 9e6dd4c256d0 ("netlink: specs: mptcp: replace underscores with dashes in names") ec362192aa9e ("netlink: specs: fix up indentation errors")
https://lore.kernel.org/20250626122205.389c2cd4@canb.auug.org.au
Adjacent changes:
Documentation/netlink/specs/fou.yaml 791a9ed0a40d ("netlink: specs: fou: replace underscores with dashes in names") 880d43ca9aa4 ("netlink: specs: clean up spaces in brackets")
Jakub Kicinski [Tue, 24 Jun 2025 14:28:34 +0000 (07:28 -0700)]
eth: fbnic: rename fbnic_fw_clear_cmpl to fbnic_mbx_clear_cmpl
fbnic_fw_clear_cmpl() does the inverse of fbnic_mbx_set_cmpl().
It removes the completion from the mailbox table.
It also calls fbnic_mbx_set_cmpl_slot() internally.
It should have fbnic_mbx prefix, not fbnic_fw.
I'm not very clear on what the distinction is between the two
prefixes but the matching "set" and "clear" functions should
use the same prefix.
While at it move the "clear" function closer to the "set".
Jakub Kicinski [Tue, 24 Jun 2025 14:28:32 +0000 (07:28 -0700)]
eth: fbnic: realign whitespace
Relign various whitespace things. Some of it is spaces which should
be tabs and some is making sure the values are actually correctly
aligned to "columns" with 8 space tabs. Whitespace changes only.
====================
Follow-up to RGMII mode clarification: am65-cpsw fix + checkpatch
Following previous discussion [1] and the documentation update by
Andrew [2]:
Fix up the mode to account for the fixed TX delay on the AM65 CPSW
Ethernet controllers, similar to the way the icssg-prueth does it. For
backwards compatibility, the "impossible" modes that claim to have a
delay on the PCB are still accepted, but trigger a warning message.
As Andrew suggested, I have also added a checkpatch check that requires
a comment for any RGMII mode that is not "rgmii-id".
No Device Trees are updated to avoid the warning for now, to give other
projects syncing the Linux Device Trees some time to fix their drivers
as well. I intend to submit an equivalent change for U-Boot's
am65-cpsw-nuss driver as soon as the changes are accepted for Linux.
[1] https://lore.kernel.org/lkml/d25b1447-c28b-4998-b238-92672434dc28@lunn.ch/
[2] https://lore.kernel.org/all/20250430-v6-15-rc3-net-rgmii-delays-v2-1-099ae651d5e5@lunn.ch/
commit c360eb0c3ccb ("dt-bindings: net: ethernet-controller: Add informative text about RGMII delays")
v1: https://lore.kernel.org/all/cover.1744710099.git.matthias.schiffer@ew.tq-group.com/
====================
checkpatch: check for comment explaining rgmii(|-rxid|-txid) PHY modes
Historically, the RGMII PHY modes specified in Device Trees have been
used inconsistently, often referring to the usage of delays on the PHY
side rather than describing the board; many drivers still implement this
incorrectly.
Require a comment in Devices Trees using these modes (usually mentioning
that the delay is realized on the PCB), so we can avoid adding more
incorrect uses (or will at least notice which drivers still need to be
fixed).
dt-bindings: net: ti: k3-am654-cpsw-nuss: update phy-mode in example
k3-am65-cpsw-nuss controllers have a fixed internal TX delay, so RXID
mode is not actually possible and will result in a warning from the
driver going forward.
Jiawen Wu [Wed, 25 Jun 2025 02:39:24 +0000 (10:39 +0800)]
net: libwx: fix the creation of page_pool
'rx_ring->size' means the count of ring descriptors multiplied by the
size of one descriptor. When increasing the count of ring descriptors,
it may exceed the limit of pool size.
[ 864.209610] page_pool_create_percpu() gave up with errno -7
[ 864.209613] txgbe 0000:11:00.0: Page pool creation failed: -7
Fix to set the pool_size to the count of ring descriptors.
Fixes: 850b971110b2 ("net: libwx: Allocate Rx and Tx resources") Cc: stable@vger.kernel.org Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Mina Almasry <almasrymina@google.com> Link: https://patch.msgid.link/434C72BFB40E350A+20250625023924.21821-1-jiawenwu@trustnetic.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Tue, 24 Jun 2025 18:32:58 +0000 (11:32 -0700)]
net: selftests: fix TCP packet checksum
The length in the pseudo header should be the length of the L3 payload
AKA the L4 header+payload. The selftest code builds the packet from
the lower layers up, so all the headers are pushed already when it
constructs L4. We need to subtract the lower layer headers from skb->len.
Linus Torvalds [Thu, 26 Jun 2025 04:09:02 +0000 (21:09 -0700)]
Merge tag 'bpf-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Pull bpf fixes from Alexei Starovoitov:
- Fix use-after-free in libbpf when map is resized (Adin Scannell)
- Fix verifier assumptions about 2nd argument of bpf_sysctl_get_name
(Jerome Marchand)
- Fix verifier assumption of nullness of d_inode in dentry (Song Liu)
- Fix global starvation of LRU map (Willem de Bruijn)
- Fix potential NULL dereference in btf_dump__free (Yuan Chen)
* tag 'bpf-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: adapt one more case in test_lru_map to the new target_free
libbpf: Fix possible use-after-free for externs
selftests/bpf: Convert test_sysctl to prog_tests
bpf: Specify access type of bpf_sysctl_get_name args
libbpf: Fix null pointer dereference in btf_dump__free on allocation failure
bpf: Adjust free target to avoid global starvation of LRU map
bpf: Mark dentry->d_inode as trusted_or_null
Linus Torvalds [Thu, 26 Jun 2025 03:48:48 +0000 (20:48 -0700)]
Merge tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull mount fixes from Al Viro:
"Several mount-related fixes"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
userns and mnt_idmap leak in open_tree_attr(2)
attach_recursive_mnt(): do not lock the covering tree when sliding something under it
replace collect_mounts()/drop_collected_mounts() with a safer variant
net: phy: realtek: add error handling to rtl8211f_get_wol
We should check if the WOL settings was successfully read from the PHY.
In case this fails we cannot just use the error code and proceed.
Signed-off-by: Daniel Braunwarth <daniel.braunwarth@kuka.com> Reported-by: Jon Hunter <jonathanh@nvidia.com> Closes: https://lore.kernel.org/baaa083b-9a69-460f-ab35-2a7cb3246ffd@nvidia.com Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250624-realtek_fixes-v1-1-02a0b7c369bc@kuka.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
atm: Release atm_dev_mutex after removing procfs in atm_dev_deregister().
syzbot reported a warning below during atm_dev_register(). [0]
Before creating a new device and procfs/sysfs for it, atm_dev_register()
looks up a duplicated device by __atm_dev_lookup(). These operations are
done under atm_dev_mutex.
However, when removing a device in atm_dev_deregister(), it releases the
mutex just after removing the device from the list that __atm_dev_lookup()
iterates over.
So, there will be a small race window where the device does not exist on
the device list but procfs/sysfs are still not removed, triggering the
splat.
Let's hold the mutex until procfs/sysfs are removed in
atm_dev_deregister().
====================
netlink: specs: enforce strict naming of properties
I got annoyed once again by the name properties in the ethtool spec
which use underscore instead of dash. I previously assumed that there
is a lot of such properties in the specs so fixing them now would
be near impossible. On a closer look, however, I only found 22
(rough grep suggests we have ~4.8k names in the specs, so bad ones
are just 0.46%).
Add a regex to the JSON schema to enforce the naming, fix the few
bad names. I was hoping we could start enforcing this from newer
families, but there's no correlation between the protocol and the
number of errors. If anything classic netlink has more recently
added specs so it has fewer errors.
The regex is just for name properties which will end up visible
to the user (in Python or YNL CLI). I left the c-name properties
alone, those don't matter as much. C codegen rewrites them, anyway.
I'm not updating the spec for genetlink-c. Looks like it has no
users, new families use genetlink, all old ones need genetlink-legacy.
If these patches are merged I will remove genetlink-c completely
in net-next.
====================
Jakub Kicinski [Tue, 24 Jun 2025 21:10:02 +0000 (14:10 -0700)]
netlink: specs: enforce strict naming of properties
Add a regexp to make sure all names which may end up being visible
to the user consist of lower case characters, numbers and dashes.
Underscores keep sneaking into the specs, which is not visible
in the C code but makes the Python and alike inconsistent.
Note that starting with a number is okay, as in C the full
name will include the family name.
For legacy families we can't enforce the naming in the family
name or the multicast group names, as these are part of the
binary uAPI of the kernel.
For classic netlink we need to allow capital letters in names
of struct members. TC has some structs with capitalized members.
Jakub Kicinski [Tue, 24 Jun 2025 21:10:01 +0000 (14:10 -0700)]
netlink: specs: tc: replace underscores with dashes in names
We're trying to add a strict regexp for the name format in the spec.
Underscores will not be allowed, dashes should be used instead.
This makes no difference to C (codegen, if used, replaces special
chars in names) but it gives more uniform naming in Python.
Jakub Kicinski [Tue, 24 Jun 2025 21:10:00 +0000 (14:10 -0700)]
netlink: specs: rt-link: replace underscores with dashes in names
We're trying to add a strict regexp for the name format in the spec.
Underscores will not be allowed, dashes should be used instead.
This makes no difference to C (codegen, if used, replaces special
chars in names) but it gives more uniform naming in Python.
Fixes: b2f63d904e72 ("doc/netlink: Add spec for rt link messages") Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Link: https://patch.msgid.link/20250624211002.3475021-9-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 24 Jun 2025 21:09:59 +0000 (14:09 -0700)]
netlink: specs: mptcp: replace underscores with dashes in names
We're trying to add a strict regexp for the name format in the spec.
Underscores will not be allowed, dashes should be used instead.
This makes no difference to C (codegen, if used, replaces special
chars in names) but it gives more uniform naming in Python.
Fixes: bc8aeb2045e2 ("Documentation: netlink: add a YAML spec for mptcp") Reviewed-by: Davide Caratti <dcaratti@redhat.com> Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20250624211002.3475021-8-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 24 Jun 2025 21:09:58 +0000 (14:09 -0700)]
netlink: specs: ovs_flow: replace underscores with dashes in names
We're trying to add a strict regexp for the name format in the spec.
Underscores will not be allowed, dashes should be used instead.
This makes no difference to C (codegen, if used, replaces special
chars in names) but it gives more uniform naming in Python.
Fixes: 93b230b549bc ("netlink: specs: add ynl spec for ovs_flow") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Reviewed-by: Ilya Maximets <i.maximets@ovn.org> Reviewed-by: Eelco Chaudron <echaudro@redhat.com> Link: https://patch.msgid.link/20250624211002.3475021-7-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
projects / thirdparty / linux.git / log
