ath79/mikrotik: fix soft_config location for SXT 5n
The soft_config partition for these devices lays between 0xe000 and
0xf000 (as correctly detected by the RouterBoard platform driver),
before the bootloader2 partition which starts at 0x10000.
This commit correctly sorts the partitions, fixing the parsing error.
Martin Schiller [Tue, 15 Sep 2020 06:24:22 +0000 (08:24 +0200)]
lantiq: use uniform "u-boot-env" mtd label
This is the most popular choice in the linux kernel tree.
Within OpenWrt, this change will establish consistency with ath79
and ramips targets.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[extend commit message, include netgear_dm200, update base-files] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Vladimir Vid [Mon, 14 Sep 2020 15:24:24 +0000 (17:24 +0200)]
mvebu: image: add check for fdt_add_r and kernel_addr_r variables
fdt_addr and kernel_addr variables are getting obsolete in the mainline
u-boot in favor of fdt_addr_r and kernel_addr_r.
By checking if the new variables exist, we can make sure that devices with newer
version of u-boot will work while not breaking support for the existing ones.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr> Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
David Bauer [Tue, 15 Sep 2020 09:19:14 +0000 (11:19 +0200)]
ipq40xx: enable FRITZRepeater 3000 ports on switch
The ethernet ports on the AVM FRITZRepeater 3000 are not separated
between LAN and WAN in the stock firmware. OpenWrt currently abstracts
port 4 as eth0 and port 5 as eth1, bridging them in the kernel.
This patch adjusts the GMAC port bitmasks and default bitmask for ar40xx
to bridge them on the switch, avoiding traffic on both ports to pass
thru the CPU.
Follow the Ubiquiti TFTP recovery procedure for this device.
1. Hold down the reset button while connecting power for 10 seconds.
2. Transfer the factory image via TFTP to the AP (192.168.1.20)
3. Wait 2 minutes for the AP to write the firmware to flash. The device
will automatically reboot to OpenWrt.
zram-swap: default to lzo instead of lzo-rle compression
On devices with small amounts of RAM, zram-swap fails to initialise due to the
default compression algorithm (lzo-rle). Startup example on an AirGrid M2, with
32 MiB of RAM:
root@airgrid:/etc/config# /etc/init.d/zram start
zram_start: activating '/dev/zram0' for swapping (13 MegaBytes)
zram_reset: enforcing defaults via /sys/block/zram0/reset
sh: write error: Out of memory
mkswap: image is too small
swapon: /dev/zram0: Invalid argument
root@airgrid:/etc/config#
Fix this by defaulting to traditional lzo, which works fine and is always
available.
John Crispin [Mon, 7 Sep 2020 11:08:41 +0000 (13:08 +0200)]
ipq40xx: add Edgecore OAP-100 support
flashing the unit
* first update to latest edcore FW as per the PDF instructions
* boot the initramfs
- tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm
* inside the initramfs call the following commiands
- ubiattach -p /dev/mtd0
- ubirmvol /dev/ubi0 -n0
- ubirmvol /dev/ubi0 -n1
- ubirmvol /dev/ubi0 -n2
* scp the sysupgrade image to the board and call
- sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin
Robert Marko [Mon, 7 Sep 2020 10:43:37 +0000 (12:43 +0200)]
ipq806x: add Edgecore ECW5410 support
This patch adds support for the Edgecore ECW5410 indoor AP.
Specification:
- SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15
- RAM: 256MB(225 usable) DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB S34MS01G2 Parallel NAND
- Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn)
- CC2540 BLE
- UART console on RJ45 next to ethernet ports exposed.
Its Cisco pin compatible, 115200 8n1 baud.
Installation instructions:
Through stock firmware or initramfs.
1.Connect to console
2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe.
3. Transfer factory image
4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path>
This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0
Note
Initramfs:
1. Connect to console
2. Transfer the image from TFTP server with tftpboot,
or by using DHCP advertised image with dhcp command.
3. bootm
4. Run ubiformat /dev/mtd1
You need to interrupt the bootloader after rebooting and run:
run altbootcmd
This will switch your active rootfs partition to one you wrote to and boot from it.
So if rootfs1 is active, then it will change it to rootfs2.
This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0
If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those.
This will result in wrong ordering and OpenWrt will panic on boot.
5. Transfer sysupgrade image
6. Flash with sysupgrade -n.
Note that sysupgrade will write the image to rootfs partition that is not currently in use.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Robert Marko [Mon, 18 May 2020 10:35:15 +0000 (12:35 +0200)]
ipq806x: import bootargs-append from IPQ40xx
This imports the patch that adds bootargs-append support from IPQ40xx.
This way we can append additional boot arguments from DTS instead of only being able to overwrite them.
This way dual firmware devices can use the rootfs number that bootloader passes to decide from what to boot.
But we still need to append console info and ubi root info.
This is used by Edgecore ECW5410.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Robert Marko [Mon, 18 May 2020 10:34:06 +0000 (12:34 +0200)]
firmware: ipq-wifi: enable use on IPQ806x
This enables the ipq-wifi package to be used on IPQ806x target.
Its needed for boards using a different BDF than one shipped in the upstream board-2.bin.
Currently needed for Edgecore ECW5410.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
ath79: fix button types for WZR-HP-AG300H and WZR-600DHP
Router and Movie "keys" are actually switches for both devices
according to the manual. This has been properly implemented in ar71xx,
but overlooked when porting to ath79.
Fixes: 480bf2827392 ("ath79: add support for Buffalo WZR-HP-AG300H") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ath79: consistently use "info" label for default-mac partition
The tp-link safeloader devices typically contain a partition
"default-mac" which stores the MAC addresses. It is followed by other
partitions containing device info, like
In DTS, we typically assign a 0x10000 sized partition for these,
which is mostly labelled "mac" or "info". In rarer cases, the
partitions have been enclosed in a larger "tplink" or "config"
partition.
However, when comparing different devices, the implementation appears
relatively arbitrary at the moment.
Thus, this PR aims at harmonizing these partitions by always using
the name "info" for the DTS partition containing "default-mac".
"info" is preferred over "mac" as we never just have "default-mac"
alone, but always some other device-info partitions as well.
While at it, this also establishes a similar partitioning for the
few devices where the "info" partitions are part of a bigger
unspecific "config" partition or similar.
Besides the harmonization itself, this also allows to merge a few
cases in 11-ath10k-caldata.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
vconfig has been disabled by default since 2015 [1] and there are
no remaining uses in entire OpenWrt trunk. However, we still set up
a specific name_type for it during boot.
While this setup is properly implemented to be only triggered when
vconfig is present, it still seems anachronistic and unnecessary
to set up a standard for a tool that is not used anymore.
Therefore, this removes the set_name_type initialization and leaves
it for those people actually using the tool to configure it as needed.
The reverted shell code is a very poor reimplementation of the existing
package-metadata.pl usergroup subcommand and the resulting file is not
used anymore, so drop this code.
Use the prepared .packageusergroup file to lookup user and group names
when processing the passed file mode.
Also replace the various subshell/cut invocations with a sequence of
standard variable interpolations which fixes paths with embedded colons
as a side-effect.
Paul Spooren [Mon, 14 Sep 2020 02:02:02 +0000 (16:02 -1000)]
build: add user/group ID resolve function
With the introduction of `./tmp/userids` the `ipkg-build` script can now
resolve values of "PKG_FILE_MODES", allowing users to set names rather
than numeric values.
Paul Spooren [Mon, 14 Sep 2020 01:55:52 +0000 (15:55 -1000)]
build: create tmp/userids file
Multiple packages contain a USERID variable defining required user and
group for the package to run. With the recent addition of
"PKG_FILE_MODES" it is possible to define user and group of specific
files, replacing (possibly insecure) post-inst scripts. These modes are
set during build time and put directly into the packages.
To allow user and group names rather than the numeric values, a mapping
like `/etc/passwd` is required by the `ipkg-build` script, mapping names
defined in "PKG_FILE_MODES" to a numeric value, as the build system does
not create any users during build.
This commit adds a single line to the `prepare-tmpinfo` target, so that
everytime the feeds are updated the *passwd like* content of
`./tmp/userids` is updated.
This adds support for the RTL838x Architecture.
SoCs of this type are used in managed and un-managed Switches and Routers
with 8-28 ports. Drivers are provided for SoC initialization, GPIOs, Flash,
Ethernet including a DSA switch driver and internal and external PHYs used
with these switches.
Supported SoCs:
RTL8380M
RTL8381M
RTL8382M
The kernel will also boot on the following RTL839x SoCs, however driver
support apart from spi-nor is missing:
RTL8390
RTL8391
RTL8393
The following PHYs are supported:
RTL8214FC (Quad QSGMII multiplexing GMAC and SFP port)
RTL8218B internal: internal PHY of the RTL838x chips
RTL8318b external (QSGMII 8-port GMAC phy)
RTL8382M SerDes for 2 SFP ports
Initialization sequences for the PHYs are provided in the form of
firmware files.
Flash driver supports 3 / 4 byte access
DSA switch driver supports VLANs, port isolation, STP and port mirroring.
The ALLNET ALL-SG8208M is supported as Proof of Concept:
RTL8382M SoC
1 MIPS 4KEc core @ 500MHz
8 Internal PHYs (RTL8218B)
128MB DRAM (Nanya NT5TU128MB)
16MB NOR Flash (MXIC 25L128)
8 GBEthernet ports with one green status LED each (SoC controlled)
1 Power LED (not configurable)
1 SYS LED (configurable)
1 On-Off switch (not configurable)
1 Reset button at the right behind right air-vent (not configurable)
1 Reset button on front panel (configurable)
12V 1A barrel connector
1 serial header with populated standard pin connector and with markings
GND TX RX Vcc(3.3V), connection properties: 115200 8N1
To install, upload the sysupgrade image to the OEM webpage.
Klaus Kudielka [Fri, 27 Dec 2019 18:15:31 +0000 (19:15 +0100)]
uboot-envtools: mvebu: update uci defaults for Turris Omnia
On the Turris Omnia 2019, u-boot environment is located at 0xF0000, instead
of 0xC0000. The switch happened with u-boot-omnia package version 2019-04-2
(May 10, 2019).
Check the installed u-boot release, and set the default accordingly.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
[bump PKG_RELEASE, use lower case for hex offset] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ramips: mt7621: pbr-m1: add pcie reset for asm1061
this board has a pcie to sata bridge connected to pcie2 with a
separated pcie reset on gpio7.
add reset-gpios and corresponding pinctrl nodes into dts.
Felix Fietkau [Sun, 13 Sep 2020 07:34:37 +0000 (09:34 +0200)]
ramips/mediatek: improve GRO performance, fix PPE packet parsing
Backport upstream changes to initialize GDM settings and reset PPE
Allow GMAC to recognize the special tag to fix PPE packet parsing
Improve GRO performance by passing PPE L4 hash as skb hash
TP-Link EAP225-Wall v2 is an AC1200 (802.11ac Wave-2) wall plate access
point. UART access and debricking require fine soldering.
The device was kindly provided for porting by Stijn Segers.
Device specifications:
* SoC: QCA9561 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (GD25Q127CSIG)
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (SoC): 4× 100Mbps
* Eth0 (back): 802.3af/at PoE in
* Eth1, Eth2 (bottom)
* Eth3 (bottom): PoE out (can be toggled by GPIO)
* One status LED
* Two buttons (both work as failsafe)
* LED button, implemented as KEY_BRIGHTNESS_TOGGLE
* Reset button
Flashing instructions, requires recent firmware (tested on 1.20.0):
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface
Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
* Bridge unpopulated resistors R162 (TXD) and R165 (RXD)
Do NOT bridge R164
* Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via sysupgrade or LuCI web interface
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM ifconfig:
br0 Link encap:Ethernet HWaddr 50:...:04
eth0 Link encap:Ethernet HWaddr 50:...:04
wifi0 Link encap:UNSPEC HWaddr 50-...-04-...
wifi1 Link encap:UNSPEC HWaddr 50-...-05-...
Signed-off-by: Sander Vanheule <sander@svanheule.net>
[fix IMAGE_SIZE] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: John Audia <graysky@archlinux.us>
[add community build/run tests to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The baud rate for the RAVPower RP-WD03 is 57600, not 115200.
Since this is the default from mt7620n.dtsi, the chosen node can
simply be removed from the device DTS.
Fixes: 5ef79af4f80f ("ramips: add support for Ravpower WD03") Suggested-by: Russell Morris <rmorris@rkmorris.us> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The previously used location 0x4000 for ethernet is actually empty.
Therefore, fix the ethernet MAC address and set it as label-mac-address.
Fixes: 5ef79af4f80f ("ramips: add support for Ravpower WD03") Suggested-by: Russell Morris <rmorris@rkmorris.us> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ramips: fix partitions and boot for RAVPower RP-WD03
The RAVPower RP-WD03 is a battery powered router, with an Ethernet and
USB port. Due due a limitation in the vendor supplied U-Boot bootloader,
we cannot exceed a 1.5 MB kernel size, as is the case with recent builds
(i.e. post v19.07). This breaks both factory and sysupgrade images.
To address this, use the lzma loader (loader-okli) to work around this
limitation.
The improvements here also address the "misplaced" U-Boot environment
partition, which is located between the kernel and rootfs in the stock
image / implementation. This is addressed by making use of mtd-concat,
maximizing space available in the booted image.
This will make sysupgrade from earlier versions impossible.
Changes are based on the recently supported HooToo HT-TM05, as the
hardware is almost identical (except for RAM size) and is from the same
vendor (SunValley). While at it, also change the SPI frequency
accordingly.
Installation:
- Download the needed OpenWrt install files, place them in the root
of a clean TFTP server running on your computer. Rename the files as,
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel
- openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs
- Plug the router into your computer via Ethernet
- Set your computer to use 10.10.10.254 as its IP address
- With your router shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The router (10.10.10.128) will look for your computer at 10.10.10.254
and install the two files. Once it has finished installation, it will
automatically reboot and start up OpenWrt.
- Set your computer to use DHCP for its IP address
Notes:
- U-Boot environment can be modified, u-boot-env is preserved on initial
install or sysupgrade
- mtd-concat functionality is included, to leave a "hole" for u-boot-env,
combining the OEM kernel and rootfs partitions
Most of the changes in this commit are the work of Russell Morris (as
credited below), I only wrapped them up and added compat-version.
Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader
to work!
Fixes: 5ef79af4f80f ("ramips: add support for Ravpower WD03") Suggested-by: Russell Morris <rmorris@rkmorris.us> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
David Bauer [Sat, 5 Sep 2020 23:24:00 +0000 (01:24 +0200)]
ipq40xx: essedma: enable VLAN tag offload for single-port
Enable the VLAN tag offloading mechanism for RGMII single-port devices.
This allows those devices to use 802.1Q VLANs on the ethernet port.
Previously, RX frames were double tagged, as the RX TAG removal flag was
not enabled and an additional 802.1Q header was inserted elsewhere in
the code.
On the TX side, tagging was completely not present for single-port
devices. Enable tagging if an 802.1Q frame should be transmitted and
disable the default tagging mechanism for single-port devices.
David Bauer [Sun, 26 Jul 2020 20:37:53 +0000 (22:37 +0200)]
base-files: disable LEDs if default state is undefined
Set the default state for LEDs to off. When a trigger is set, the
trigger will turn the LED automatically on.
Currently LEDs might stay on, e.g. when the LED trigger is set to a
netdev trigger and the interface is never activated or the 'none'
trigger is selected without setting the 'default' option to 0 and it's
set for the LED indicating the system running state.
Using off as a default value is also consistent with the documentation
in the OpenWrt wiki.
vconfig is no more installed by default to a firmware image. So, replace
vconfig calls for VLAN subinterface configuration by coresponding
ip-link commands.
Also drop few useless comments from the preinit hook script, while we
are at it.
I have no chance to test this fix since I have no board with a subject
switch IC, but this is still better then call an utility that is
unavailable in the firmware for years.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
[use documented syntax for ip link add] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since the introduction of fakeroot support, wrapped SDK executables might
be invoked from a shell that has libfakeroot.so preloaded.
Since we're using preloading as well in order to mangle argv[0] when
invoking the shipped ELF interpreter directly, we must take care of
preloading the already preloaded libraries as well, to avoid invoked
programs losing their fakeroot capabilities.
Extend the bundle-libraries.sh script to take any existing $LD_PRELOAD
into account when invoking the target ELF executable with a preloaded
runas.so library.
This is in preparation for FreeBSD support, which I had hoped to have this
release, but we're still waiting on some tooling fixes, so hopefully next
wg(8) will support that. Either way, the code base is now a lot more amenable
to adding more kernel platform support.
* man: wg-quick: use syncconf instead of addconf for strip example
Simple documentation fix.
* pubkey: isblank is a subset of isspace
* ctype: use non-locale-specific ctype.h
In addition to ensuring that isalpha() and such isn't locale-specific, we also
make these constant time, even though we're never distinguishing between bits
of a secret using them. From that perspective, though, this is markedly better
than the locale-specific table lookups in glibc, even though base64 characters
span two cache lines and valid private keys must hit both. This may be useful
for other projects too: https://git.zx2c4.com/wireguard-tools/tree/src/ctype.h
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Sander Vanheule [Thu, 4 Jun 2020 18:59:13 +0000 (20:59 +0200)]
ath79: add support for TP-Link EAP245-v3
TP-Link EAP245 v3 is an AC1750 (802.11ac Wave-2) ceiling mount access
point. UART access (for debricking) requires non-trivial soldering.
Specifications:
* SoC: QCA9563 (CPU/DDR/AHB @ 775/650/258 MHz)
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 3x3
* Wireless 5GHz (QCA9982): a/n/ac 3x3 with MU-MIMO
* Ethernet (QCA8337N switch): 2× 1GbE, ETH1 (802.3at PoE) and ETH2
* Green and amber status LEDs
* Reset switch (GPIO, available for failsafe)
Flashing instructions:
All recent firmware versions (latest is 2.20.0), can disable firmware
signature verification and use a padded firmware file to flash OpenWrt:
* ssh into target device and run `cliclientd stopcs`
* upload factory image via web interface
The stopcs-method is supported from firmware version 2.3.0. Earlier
versions need to be upgraded to a newer stock version before flashing
OpenWrt.
Factory images for these devices are RSA signed by TP-Link. While the
signature verification can be disabled, the factory image still needs to
have a (fake) 1024 bit signature added to pass file checks.
Debricking instructions:
You can recover using u-boot via the serial port:
* Serial port is available from J3 (1:TX, 2:RX, 3:GND, 4:3.3V)
* Bridge R237 to connect RX, located next to J3
* Bridge R225 to connect TX, located inside can on back-side of board
* Serial port is 115200 baud, 8n1, interrupt u-boot by holding ctrl+B
* Upload initramfs with tftp and upgrade via OpenWrt
Device mac addresses:
Stock firmware has the same mac address for 2.4GHz wireless and
ethernet, 5GHz is incremented by one. The base mac address is stored in
the 'default-mac' partition (offset 0x90000) at an offset of 8 bytes.
ART blobs contain no mac addresses.
From OEM ifconfig:
ath0 Link encap:Ethernet HWaddr 74:..:E2
ath10 Link encap:Ethernet HWaddr 74:..:E3
br0 Link encap:Ethernet HWaddr 74:..:E2
eth0 Link encap:Ethernet HWaddr 74:..:E2
TP-Link has introduced a compatibility level to prevent certain
downgrades. This information is stored in the soft-version partition,
changing the data length from 0xc to 0x10.
The compatibility level doesn't change frequently. For example, it has
the following values for the EAP245v3 (released 2018-Q4):
* FW v2.2.0 (2019-05-30): compat_level=0
* FW v2.3.0 (2019-07-31): compat_level=0
* FW v2.3.1 (2019-10-29): compat_level=1
* FW v2.20.0 (2020-04-23): compat_level=1
Empty flash values (0xffffffff) are interpreted as compat_level=0.
If a firmware upgrade file has a soft-version block without
compatibility level (data length < 0x10), this is also interpreted as
compat_level=0.
By including a high enough compatibility level in factory images, stock
firmware can be convinced to accept the image. A compatibility level
aware firmware will keep the original value.
Other firmware upgrades have been observed to modify the compabitility
stored level (e.g. TP-Link EAP225-Outdoor FWv1.4.1 to FWv1.7.0).
Therefore, it seems to be the safest option to set the OpenWrt
compatibility level to the highest known value instead of the highest
possible value (0xfffffffe), to ensure users do not get unexpectedly
refused firmware upgrades when using a device reverted back to stock.
To remain compatible with existing devices and not produce different
images, the image builder doesn't store a compatibility level if it is
zero.
To parse the ELF kernel loader, a small ELF parser is used that can
handle both ELF32 or ELF64 class loaders. The splitter assumes that the
kernel is always located before the rootfs, whether it is embedded in
the loader or not. If the kernel is located after the rootfs on the
firmware partition, then the rootfs splitter will include it in the
dynamically created rootfs_data partition and the kernel will be
corrupted.
The kernel image is preferably embedded inside the ELF loader, so the
end of the loader equals the end of the kernel partition. This is due to
the way mtd_find_rootfs_from searches for the the rootfs:
- if the kernel image is embedded in the loader, the appended rootfs may
follow the loader immediately, within the same erase block.
- if the kernel image is not embedded in the loader, but placed at some
offset behind the loader (OKLI-style loader), the rootfs must be
aligned to an erase-block after the loader and kernel image.
In case section header table is empty, determine the elf loader size by
finding the end of the last segment, as defined by the program header
table.
Currently the global variable PKG_FILE_MODES is used for all ipkg
creations. This works for Makefiles which output a single package, or
variants of a single package.
But if a Makefile outputs multiple packages that each contain different
files, setting PKG_FILE_MODES causes build failure when any of the files
in the variable do not exist in the folder that is currently being
packaged.
Example:
/openwrt/staging_dir/host/bin/fakeroot -l /openwrt/staging_dir/host/lib/libfakeroot.so -f /openwrt/staging_dir/host/bin/faked /openwrt/scripts/ipkg-build -m "/usr/lib/mariadb/plugin/auth_pam_tool_dir:root:376:0750" /openwrt/build_dir/target-mips_24kc_musl/mariadb-10.4.13/ipkg-mips_24kc/mariadb-server-plugin-disks /openwrt/bin/packages/mips_24kc/packages
+chown: cannot access '/openwrt/build_dir/target-mips_24kc_musl/mariadb-10.4.13/ipkg-mips_24kc/mariadb-server-plugin-disks//usr/lib/mariadb/plugin/auth_pam_tool_dir': No such file or directory
This commit changes the file mode handling a bit. The file mode can now
be set either globally via PKG_FILE_MODES (no behavior change) or on a
per-package basis via FILE_MODES. This way specific file modes can be
used for any particular package.
This behavior is already used for other OpenWrt variables, hence it is
familiar:
PKG_MAINTAINER vs MAINTAINER
PKG_SOURCE_SUBDIR vs SUBDIR
PKG_LICENSE vs LICENSE
...
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
* compat: backport kfree_sensitive and switch to it
* netlink: consistently use NLA_POLICY_EXACT_LEN()
* netlink: consistently use NLA_POLICY_MIN_LEN()
* compat: backport NLA policy macros
Backports from upstream changes.
* peerlookup: take lock before checking hash in replace operation
A fix for a race condition caught by syzkaller.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Daniel Golle [Tue, 8 Sep 2020 19:01:11 +0000 (20:01 +0100)]
netifd: update to git HEAD
3d9bd73 utils: fix check_pid_path to work with deleted file as well 330f403 vlan: initialize device ifname earlier at creation time c057e71 device: do not check state from within device_init cb0c07b system-dummy: fix resolving ifindex ccd9ddc bridge: add support for turning on vlan_filtering 82bcb64 bridge: add support for adding vlans to a bridge 0e8cea0 bridge: add support for VLAN filtering 6086b63 config: enable bridge vlan filtering by default for bridges that define VLANs ac0710b device: look up full device name before traversing vlan chain e32e21e bridge: flush vlan list on bridge free 645ceed interface-ip: clear host bits of the device prefix d7b614a netifd-wireless: parse 'osen' encryption
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
treewide: revert sysupgrade adjustments for early DSA-adopters
The uci-default mechanism to update the compat-version was only
meant for early DSA-adopters, which should have updated by now.
Remove this workaround again in order to prevent the intended
experiences for all the other people.
This reverts: a9703db72030 ("mvebu: fix sysupgrade experience for early DSA-adopters") 86c89bf5e8f5 ("kirkwood: fix sysupgrade experience for early DSA-adopters")
Partially reverted: 1eac573b5304 ("ramips: mt7621: implement compatibility version for DSA migration")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Ed25519 key pairs are much shorter than RSA pairs and are supported
by default in OpenSSH. Looking at websites explaining how to create new
SSH keys, many suggest using Ed25519 rather than RSA, however consider
the former as not yet widely established. OpenWrt likely has a positive
influence on that development.
As enabling Ed25519 is a compile time option, it is currently not
possible to install the feature via `opkg` nor select that option in an
ImageBuilder.
Due to the size impact of **12kB** the option should only be enabled for
devices with `!SMALL_FLASH`.
This approach seems cleaner than splitting `dropbear` into two packages
like `dropbear` and `dropbear-ed25519`.
When the libmagic from the file package in the packages feed was also
compiled and provided its libmagic.so file, util-linux tried to link
against it. Avoid this by explicitly disable libmagic support.
This fixes the following build error:
Package more is missing dependencies for the following libraries:
libmagic.so.1
projects / thirdparty / openwrt.git / log
