John Crispin [Mon, 24 Nov 2014 19:14:29 +0000 (19:14 +0000)]
procd: fix/clean some conditions in nand.sh
1) nand_upgrade_tar: use a simpler condition that matches if () { }
logic and fix check of $kernel_length variable
2) nand_do_upgrade_stage2: use case, otherwise one could believe we
always call nand_upgrade_tar
John Crispin [Mon, 24 Nov 2014 19:12:46 +0000 (19:12 +0000)]
mpc85xx: fix missing dts target for kernel 3.14
With kernel 3.14 dts target p1010rdb was renamed to p1010rdb-pa.
To maintain compatibility define p1010rdb-pa as new standard and
copy p1010rdb.dts to p1010rdb-pa.dts under 3.10.
Jonas Gorski [Mon, 24 Nov 2014 14:44:46 +0000 (14:44 +0000)]
brcm63xx: do not build images for unsupported routers
If there is no board support in the kernel, it does not make sense to
build images for devices. So drop any images for board ids for which
there are nc corresponding board_info structs in the kernel.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43364
Felix Fietkau [Mon, 24 Nov 2014 09:33:48 +0000 (09:33 +0000)]
ar8216: Fix issue with autoneg being disabled under 3.14, revert 43332
Patch reverts 43332 which seems to cause issues with VLAN functionality.
Add a specific check to check whether ANEG is still enabled and re-enable
it if necessary. Disable generic phy soft reset for kernel >=3.16.
Jonas Gorski [Sat, 22 Nov 2014 12:25:52 +0000 (12:25 +0000)]
brcm63xx: move board compatible strings into a table
Move compatible strings from board structs into separate table. This
allows for several board compatibles to match to the same board in case
e.g. only the flash size / partitions differ.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43341
Felix Fietkau [Thu, 20 Nov 2014 15:19:15 +0000 (15:19 +0000)]
ar8216: Use generic hw_init from ar8236 for ar8216 too
We should make sure that also for ar8216 hw gets initialized.
For ar8216 hw_init is a dummy currently. The hw_init used for ar8236
should be generic enough to be usable with ar8216 too.
Felix Fietkau [Wed, 19 Nov 2014 20:18:01 +0000 (20:18 +0000)]
ar8216: use genphy_config_aneg also for PHY 0
Kernel 3.14 introduced a switch reset in phy_init_hw in drivers/net/phy
causing BMCR_ANENABLE to get cleared.
Due to the fact that ar8xxx_phy_config_aneg does nothing for
PHY 0 autonegatiation support remains disabled.
This can cause ports to operate at 10MBit/half-duplex only.
Fix this by calling genphy_config_aneg for PHY 0 too as
genphy_config_aneg sets BMCR_ANENABLE if it's not yet set. Fixes: ticket 17800 Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43332
Felix Fietkau [Wed, 19 Nov 2014 20:17:37 +0000 (20:17 +0000)]
ar8216: after a switch reset poll until BCMR_RESET is cleared
Currently there is a fixed 1000ms wait time after the switch was reset.
Most if not all switches need much less time to perform a reset.
Therefore replace the fixed wait time with polling for BMCR_RESET to
be cleared.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43329
Felix Fietkau [Wed, 19 Nov 2014 20:17:30 +0000 (20:17 +0000)]
ar8216: introduce global constant for number of PHYs
All supported switches have 5 PHYs. Currently partially 5 is hardcoded
and partially switch-specific constants exist.
Replace them with a global constant.
Felix Fietkau [Wed, 19 Nov 2014 20:16:50 +0000 (20:16 +0000)]
build: allow AutoLoad and AutoProbe to specify modules not included in the package
On out-of-tree modules depending on other out-of-tree modules from a
different tree, module dependencies are not filled properly.
This change helps with adding those dependencies in the AutoLoad call
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43323
John Crispin [Wed, 19 Nov 2014 14:09:10 +0000 (14:09 +0000)]
gemini: add basic nas4220 board support
Few notes:
- redboot partitions are unusable
- redboot declares only 16M of RAM, hence the mem arg in cmdline and separate kernel config
- boots fine but only ethernet works for now
- split wiliboard and raidsonic boards into different subtargets
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 43319
John Crispin [Wed, 19 Nov 2014 14:09:01 +0000 (14:09 +0000)]
keernel: Fixed dependencies in netfilter modules introduced with 3.18 kernel
Building current trunk with 3.18 kernel fired some errors like 'missed
dependancy of module XXX from library kmod_YYY.ko'. These patch fixes 3
of such issues which are critical to have a successful build.
Signed-off-by: Alexey N Vinogradov <a.n.vinogradov@gmail.com>
SVN-Revision: 43318
Jonas Gorski [Wed, 19 Nov 2014 12:42:00 +0000 (12:42 +0000)]
kernel: remove gpio-pwm kmod definition
r37490 removed the actual driver but left the kmod definition intact,
causing the build system hapily creating an empty package for it.
Remove it also to not make it seem as if it still exists.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43316
Jonas Gorski [Wed, 19 Nov 2014 12:17:34 +0000 (12:17 +0000)]
toolchain: musl: fix symlink for ldd
ld-musl-*.so* is a symlink "broken" for the hostsystem, so wildcard
will skip it, causing LD_MUSL_NAME to empty and the ldd symlink pointing
to ../../lib directly.
This causes sysupgrade failing to copy any linked libaries and
consequently failing to run anything after switching to ram disk.
Fix this by creating a symlink directly pointing to where ld-musl-*.so*
points to.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43314
John Crispin [Wed, 19 Nov 2014 09:20:55 +0000 (09:20 +0000)]
mpc85xx: add 3.14 kernel support for mpc85xx platform
This patch adds 3.14 kernel support for the mpc85xx platform.
Works fine here with a TL-WDR4900 which seems to be the only
supported device using this platform.
There might be differences depending on HW version, therefore
I'd ask others to test too.
Changes to 3.10
missing config options added to 3.14 config file
patch 001: rebased
patch 100: rebased
patch 110: rebased
patch 120: rebased
patch 130: rebased
patch 140: minor adjustment
patch 200: removed, change went upstream
patch 210: rebased
patch 220: removed, change went upstream
patch 750: new, fixes an issue with ethernet port autoneg being
disabled due to changes in kernel phy handling
John Crispin [Wed, 19 Nov 2014 09:19:57 +0000 (09:19 +0000)]
ralink: fix tx vlan offload and hardware status
hardware status and tx vlan offload support on all targets
except rt5350. so i modify the IS_ENABLE condition only for
mt7621.
support mt7621 hardware status reference by SDK. but i don't
have mt7621. if not work just set mt7621 FE_REG_FE_COUNTER_BASE
to 0 to let software count.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43303
John Crispin [Wed, 19 Nov 2014 09:19:43 +0000 (09:19 +0000)]
ralink: improve tx vlan offload
hardware tx vlan offload only support max 16 vids
now use add/delete vlan interface to update vlan id table
when duplicate vlan id index detect.
disable hardware tx vlan offload support.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43301
Jonas Gorski [Tue, 18 Nov 2014 15:19:46 +0000 (15:19 +0000)]
base-files: properly fix copying ld*.so with eglibc
r36107 ("base-files: sysupgrade fail with eglibc") tried to fix
sysupgrade by changing the ld-soname to what is expected, but only
fixed MIPS while breaking ARM.
The underlying issue is that the ld.so name varies widely across
different architectures for eglibc:
Instead of adding each different soname to check for and copy it,
replace the awk script with a sed script to extract it properly and
drop the hardcoded so-name.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43295
projects / thirdparty / openwrt.git / log
