In commit 7608a43d8f2e ("locking/mutexes: Use MUTEX_SPIN_ON_OWNER when
appropriate") the owner field in the mutex was updated from being
dependent upon CONFIG_SMP to using optimistic spin. Update our peek
function to suite.
During hibernation the cached DP port register value will be left with
whatever value we have there when we create the hibernation image.
Currently that means the port (and eDP PLL) will be off in the cached
value. However when we resume there is no guarantee that the value
in the actual register will match the cached value. If i915 isn't
loaded in the kernel that loads the hibernation image, the port may
well be on (eg. left on by the BIOS). The encoder state readout
does the right thing in this case and updates our encoder state
to reflect the actual hardware state. However the post-resume modeset
will then use the stale cached port register value in
intel_dp_link_down() and potentially confuse the hardware.
This was caught by the following assert
WARNING: CPU: 3 PID: 5288 at ../drivers/gpu/drm/i915/intel_dp.c:2184 assert_edp_pll+0x99/0xa0 [i915]
eDP PLL state assertion failure (expected on, current off)
on account of the eDP PLL getting prematurely turned off when
shutting down the port, since the DP_PLL_ENABLE bit wasn't set
in the cached register value.
Presumably I introduced this problem in
commit 6fec76628333 ("drm/i915: Use intel_dp->DP in eDP PLL setup")
as before that we didn't update the cached value after shuttting the
port down. That's assuming the port got enabled at least once prior
to hibernating. If that didn't happen then the cached value would
still have been totally out of sync with reality (eg. first boot w/o
eDP on, then hibernate, and then resume with eDP on).
So, let's fix this properly and refresh the cached register value from
the hardware register during resume.
DDI platforms shouldn't use the cached value during port disable at
least, so shouldn't have this particular issue. They might still have
issues if we skip the initial modeset and then try to retrain the link
or something. But untangling this DP vs. DDI mess is a bigger topic,
so let's jut punt on DDI for now.
This was kind of a difficult bug to track down. If you're using a
Haswell system running GNOME and you have fbc completely enabled and
working, playing videos can result in video artifacts. Steps to
reproduce:
- Run GNOME
- Ensure FBC is enabled and active
- Download a movie, I used the ogg version of Big Buck Bunny for this
- Run `gst-launch-1.0 filesrc location='some_movie.ogg' ! decodebin !
glimagesink` in a terminal
- Watch for about over a minute, you'll see small horizontal lines go
down the screen.
For the time being, disable FBC for Haswell by default.
Stefan Richter reported kernel freezes (no video artifacts) when fbc
is on. (E3-1245 v3 with HD P4600; openbox and some KDE and LXDE
applications, thread begins at https://lkml.org/lkml/2016/4/26/813).
We also got reports from Steven Honeyman on openbox+roxterm.
v2 (From Paulo):
- Add extra information to the commit message
- Add Fixes tag
- Rebase
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96461
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96464 Fixes: a98ee79317b4 ("drm/i915/fbc: enable FBC by default on HSW and BDW") Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Lyude <cpaul@redhat.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1465487895-7401-1-git-send-email-cpaul@redhat.com
(cherry picked from commit c7f7e2feffb0294302041507dfd5fc15f01afccc) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thanks to Ville Syrjälä for pointing me towards the cause of this issue.
Unfortunately one of the sideaffects of having the refclk for a DPLL set
to SSC is that as long as it's set to SSC, the GPU will prevent us from
powering down any of the pipes or transcoders using it. A couple of
BIOSes enable SSC in both PCH_DREF_CONTROL and in the DPLL
configurations. This causes issues on the first modeset, since we don't
expect SSC to be left on and as a result, can't successfully power down
the pipes or the transcoders using it. Here's an example from this Dell
OptiPlex 990:
[drm:intel_modeset_init] SSC enabled by BIOS, overriding VBT which says disabled
[drm:intel_modeset_init] 2 display pipes available.
[drm:intel_update_cdclk] Current CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max dotclock rate: 360000 kHz
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[drm:intel_crt_reset] crt adpa set to 0xf40000
[drm:intel_dp_init_connector] Adding DP connector on port C
[drm:intel_dp_aux_init] registering DPDDC-C bus for card0-DP-1
[drm:ironlake_init_pch_refclk] has_panel 0 has_lvds 0 has_ck505 0
[drm:ironlake_init_pch_refclk] Disabling SSC entirely
… later we try committing the first modeset …
[drm:intel_dump_pipe_config] [CRTC:26][modeset] config ffff88041b02e800 for pipe A
[drm:intel_dump_pipe_config] cpu_transcoder: A
…
[drm:intel_dump_pipe_config] dpll_hw_state: dpll: 0xc4016001, dpll_md: 0x0, fp0: 0x20e08, fp1: 0x30d07
[drm:intel_dump_pipe_config] planes on this crtc
[drm:intel_dump_pipe_config] STANDARD PLANE:23 plane: 0.0 idx: 0 enabled
[drm:intel_dump_pipe_config] FB:42, fb = 800x600 format = 0x34325258
[drm:intel_dump_pipe_config] scaler:0 src (0, 0) 800x600 dst (0, 0) 800x600
[drm:intel_dump_pipe_config] CURSOR PLANE:25 plane: 0.1 idx: 1 disabled, scaler_id = 0
[drm:intel_dump_pipe_config] STANDARD PLANE:27 plane: 0.1 idx: 2 disabled, scaler_id = 0
[drm:intel_get_shared_dpll] CRTC:26 allocated PCH DPLL A
[drm:intel_get_shared_dpll] using PCH DPLL A for pipe A
[drm:ilk_audio_codec_disable] Disable audio codec on port C, pipe A
[drm:intel_disable_pipe] disabling pipe A
------------[ cut here ]------------
WARNING: CPU: 1 PID: 130 at drivers/gpu/drm/i915/intel_display.c:1146 intel_disable_pipe+0x297/0x2d0 [i915]
pipe_off wait timed out
…
---[ end trace 94fc8aa03ae139e8 ]---
[drm:intel_dp_link_down]
[drm:ironlake_crtc_disable [i915]] *ERROR* failed to disable transcoder A
Later modesets succeed since they reset the DPLL's configuration anyway,
but this is enough to get stuck with a big fat warning in dmesg.
A better solution would be to add refcounts for the SSC source, but for
now leaving the source clock on should suffice.
Changes since v4:
- Fix calculation of final for systems with LVDS panels (fixes BUG() on
CI test suite)
Changes since v3:
- Move temp variable into loop
- Move checks for using_ssc_source to after we've figured out has_ck505
- Add using_ssc_source to debug output
Changes since v2:
- Fix debug output for when we disable the CPU source
Changes since v1:
- Leave the SSC source clock on instead of just shutting it off on all
of the DPLL configurations.
It appears that, for whatever reason, both link A and B use the same
register to control the training pattern. It's a little odd, as the
GPUs before this (Tesla/Fermi1) have per-link registers, as do newer
GPUs (Maxwell).
Fixes the third DP output on NVS 510 (GK107).
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not clearing mst manager's proposed vcpis table for destroyed connectors when the manager is stopped leaves it pointing to unrefernced memory, this causes pagefault when the manager is restarted when plugging back a branch.
Fixes: 91a25e463130 ("drm/dp/mst: deallocate payload on port destruction") Signed-off-by: Andrey Grodzovsky <Andrey.Grodzovsky@amd.com> Reviewed-by: Lyude <cpaul@redhat.com> Cc: Mykola Lysenko <Mykola.Lysenko@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amdkfd need to destroy the debug manager in case amdkfd's notifier
function is called before the unbind function, because in that case,
the unbind function will exit without destroying debug manager.
When unbinding a process from a device (initiated by amd_iommu_v2), the
driver needs to make sure that process still exists in the process table.
There is a possibility that amdkfd's own notifier handler -
kfd_process_notifier_release() - was called before the unbind function
and it already removed the process from the process table.
v2:
Because there can be only one process with the specified pasid, and
because *p can't be NULL inside the hash_for_each_rcu macro, it is more
reasonable to just put the whole code inside the if statement that
compares the pasid value. That way, when we exit hash_for_each_rcu, we
simply exit the function as well.
recover_peb() was never power cut aware,
if a power cut happened right after writing the VID header
upon next attach UBI would blindly use the new partial written
PEB and all data from the old PEB is lost.
In order to make recover_peb() power cut aware, write the new
VID with a proper crc and copy_flag set such that the UBI attach
process will detect whether the new PEB is completely written
or not.
We cannot directly use ubi_eba_atomic_leb_change() since we'd
have to unlock the LEB which is facing a write error.
amdgpu_cgs_acpi_eval_object() returned the value of variable "result"
without initializing it first.
This bug has been found by compiling the kernel with clang. The
compiler complained:
drivers/gpu/drm/amd/amdgpu/amdgpu_cgs.c:972:14: error: variable
'result' is used uninitialized whenever 'for' loop exits because its
condition is false [-Werror,-Wsometimes-uninitialized]
for (i = 0; i < count; i++) {
^~~~~~~~~
drivers/gpu/drm/amd/amdgpu/amdgpu_cgs.c:1011:9: note: uninitialized
use occurs here
return result;
^~~~~~
drivers/gpu/drm/amd/amdgpu/amdgpu_cgs.c:972:14: note: remove the
condition if it is always true
for (i = 0; i < count; i++) {
^~~~~~~~~
drivers/gpu/drm/amd/amdgpu/amdgpu_cgs.c:864:12: note: initialize the
variable 'result' to silence this warning
int result;
^
= 0
Fixes: 3f1d35a03b3c ("drm/amdgpu: implement new cgs interface for acpi
function") Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When executing in a PCI passthrough based virtuzliation environment, the
hypervisor will usually attempt to send a PCIe bus reset signal to the
ASIC when the VM reboots. In this scenario, the card is not correctly
initialized, but we still consider it to be posted. Therefore, in a
passthrough based environemnt we should always post the card to guarantee
it is in a good state for driver initialization.
Ported from amdgpu commit:
amdgpu: fix asic initialization for virtualized environments
Cc: Andres Rodriguez <andres.rodriguez@amd.com> Cc: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The test for !trans->blocks_used in btrfs_abort_transaction is
insufficient to determine whether it's safe to drop the transaction
handle on the floor. btrfs_cow_block, informed by should_cow_block,
can return blocks that have already been CoW'd in the current
transaction. trans->blocks_used is only incremented for new block
allocations. If an operation overlaps the blocks in the current
transaction entirely and must abort the transaction, we'll happily
let it clean up the trans handle even though it may have modified
the blocks and will commit an incomplete operation.
In the long-term, I'd like to do closer tracking of when the fs
is actually modified so we can still recover as gracefully as possible,
but that approach will need some discussion. In the short term,
since this is the only code using trans->blocks_used, let's just
switch it to a bool indicating whether any blocks were used and set
it when should_cow_block returns false.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For non-atomic allocations, pcpu_alloc() can try to extend the area
map synchronously after dropping pcpu_lock; however, the extension
wasn't synchronized against chunk destruction and the chunk might get
freed while extension is in progress.
This patch fixes the bug by putting most of non-atomic allocations
under pcpu_alloc_mutex to synchronize against pcpu_balance_work which
is responsible for async chunk management including destruction.
Atomic allocations can trigger async map extensions which is serviced
by chunk->map_extend_work. pcpu_balance_work which is responsible for
destroying idle chunks wasn't synchronizing properly against
chunk->map_extend_work and may end up freeing the chunk while the work
item is still in flight.
This patch fixes the bug by rolling async map extension operations
into pcpu_balance_work.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-and-tested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com> Reported-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: Sasha Levin <sasha.levin@oracle.com> Fixes: 9c824b6a172c ("percpu: make sure chunk->map array has available space") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Overlayfs uses separate inodes even in the case of hard links on the
underlying filesystems. This is a problem for AF_UNIX socket
implementation which indexes sockets based on the inode. This resulted in
hard linked sockets not working.
If we take an exception while at EL1, the exception handler inherits
the original context's addr_limit and PSTATE.UAO values. To be consistent
always reset addr_limit and PSTATE.UAO on (re-)entry to EL1. This
prevents accidental re-use of the original context's addr_limit.
Based on a similar patch for arm from Russell King.
Acked-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__sync_icache_dcache unconditionally skips the cache maintenance for
anonymous pages, under the assumption that flushing is only required in
the presence of D-side aliases [see 7249b79f6b4cc ("arm64: Do not flush
the D-cache for anonymous pages")].
Unfortunately, this breaks migration of anonymous pages holding
self-modifying code, where userspace cannot be reasonably expected to
reissue maintenance instructions in response to a migration.
This patch fixes the problem by removing the broken page_mapping(page)
check from the cache syncing code, otherwise we may end up fetching and
executing stale instructions from the PoU.
Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the kernel is set to show unhandled signals, and a user task does not
handle a SIGILL as a result of an instruction abort, we will attempt to
log the offending instruction with dump_instr before killing the task.
We use dump_instr to log the encoding of the offending userspace
instruction. However, dump_instr is also used to dump instructions from
kernel space, and internally always switches to KERNEL_DS before dumping
the instruction with get_user. When both PAN and UAO are in use, reading
a user instruction via get_user while in KERNEL_DS will result in a
permission fault, which leads to an Oops.
As we have regs corresponding to the context of the original instruction
abort, we can inspect this and only flip to KERNEL_DS if the original
abort was taken from the kernel, avoiding this issue. At the same time,
remove the redundant (and incorrect) comments regarding the order
dump_mem and dump_instr are called in.
Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: James Morse <james.morse@arm.com> Cc: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Reported-by: Vladimir Murzin <vladimir.murzin@arm.com> Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> Fixes: 57f4959bad0a154a ("arm64: kernel: Add support for User Access Override") Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is apparently something amiss with the way the TTM code handles
DMA buffers, which the above commit was attempting to work around for
arm64 systems with non-coherent PCI. Unfortunately, this completely
breaks systems *with* coherent PCI (which appear to be the majority).
Booting a plain arm64 defconfig + CONFIG_DRM + CONFIG_DRM_NOUVEAU on
a machine with a PCI GPU having coherent dma_map_ops (in this case a
7600GT card plugged into an ARM Juno board) results in a fatal crash:
In a toss-up between the GPU seeing stale data artefacts on some systems
vs. catastrophic kernel crashes on other systems, the latter would seem
to take precedence, so revert this change until the real underlying
problem can be fixed.
Signed-off-by: Robin Murphy <robin.murphy@arm.com> Acked-by: Alexandre Courbot <acourbot@nvidia.com>
[acourbot@nvidia.com: port to Nouveau tree, remove bits in lib/] Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7ea0ed2b5be8 ("ipmi: Make the message handler easier to use for
SMI interfaces") changed handle_new_recv_msgs() to call handle_one_recv_msg()
for a smi_msg while the smi_msg is still connected to waiting_rcv_msgs list.
That could lead to following list corruption problems:
1) low-level function treats smi_msg as not connected to list
handle_one_recv_msg() could end up calling smi_send(), which
assumes the msg is not connected to list.
For example, the following sequence could corrupt list by
doing list_add_tail() for the entry still connected to other list.
Fixes: 7ea0ed2b5be8 ("ipmi: Make the message handler easier to use for SMI interfaces") Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
[Added a comment to describe why this works.] Signed-off-by: Corey Minyard <cminyard@mvista.com> Tested-by: Ye Feng <yefeng.yl@alibaba-inc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using flat regmap cache instead of RB-tree to avoid the following
lockdep warning on driver load:
WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2755 lockdep_trace_alloc+0x15c/0x160()
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
The RB-tree regmap cache needs to allocate new space on first
writes. However, allocations in an atomic context (e.g. when a
spinlock is held) are not allowed. The function regmap_write
calls map->lock, which acquires a spinlock in the fast_io case.
Since the FSL DCU driver uses MMIO, the regmap bus of type
regmap_mmio is being used which has fast_io set to true.
Use flat regmap cache and specify max register to be large
enouth to cover all registers available in LS1021a and Vybrids
register space.
Signed-off-by: Stefan Agner <stefan@agner.ch> Cc: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When proc_pid_attr_write() was changed to use memdup_user apparmor's
(interface violating) assumption that the setprocattr buffer was always
a single page was violated.
The size test is not strictly speaking needed as proc_pid_attr_write()
will reject anything larger, but for the sake of robustness we can keep
it in.
SMACK and SELinux look safe to me, but somebody else should probably
have a look just in case.
Based on original patch from Vegard Nossum <vegard.nossum@oracle.com>
modified for the case that apparmor provides null termination.
Fixes: bb646cdb12e75d82258c2f2e7746d5952d3e321a Reported-by: Vegard Nossum <vegard.nossum@oracle.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: John Johansen <john.johansen@canonical.com> Cc: Paul Moore <paul@paul-moore.com> Cc: Stephen Smalley <sds@tycho.nsa.gov> Cc: Eric Paris <eparis@parisplace.org> Cc: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Reviewed-by: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: James Morris <james.l.morris@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race condition in the AMD IOMMU init code that
causes requested unity mappings to be blocked by the IOMMU
for a short period of time. This results on boot failures
and IO_PAGE_FAULTs on some machines.
Fix this by making sure the unity mappings are installed
before all other DMA is blocked.
The map_sg callback is missing from arm_smmu_ops, but is required by
iommu.h. Similarly to most other IOMMU drivers, connect it to
default_iommu_map_sg.
rk_iommu_command() takes a struct rk_iommu and iterates over the slave
MMUs, so this is doubly wrong in that we're passing in the wrong pointer
and talking to MMUs that we shouldn't be.
Fixes: cd6438c5f844 ("iommu/rockchip: Reconstruct to support multi slaves") Signed-off-by: John Keeping <john@metanate.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modules which register drivers via standard path (driver_register) in
parallel can cause a warning:
WARNING: CPU: 2 PID: 3492 at ../fs/sysfs/dir.c:31 sysfs_warn_dup+0x62/0x80
sysfs: cannot create duplicate filename '/module/saa7146/drivers'
Modules linked in: hexium_gemini(+) mxb(+) ...
...
Call Trace:
...
[<ffffffff812e63a2>] sysfs_warn_dup+0x62/0x80
[<ffffffff812e6487>] sysfs_create_dir_ns+0x77/0x90
[<ffffffff8140f2c4>] kobject_add_internal+0xb4/0x340
[<ffffffff8140f5b8>] kobject_add+0x68/0xb0
[<ffffffff8140f631>] kobject_create_and_add+0x31/0x70
[<ffffffff8157a703>] module_add_driver+0xc3/0xd0
[<ffffffff8155e5d4>] bus_add_driver+0x154/0x280
[<ffffffff815604c0>] driver_register+0x60/0xe0
[<ffffffff8145bed0>] __pci_register_driver+0x60/0x70
[<ffffffffa0273e14>] saa7146_register_extension+0x64/0x90 [saa7146]
[<ffffffffa0033011>] hexium_init_module+0x11/0x1000 [hexium_gemini]
...
As can be (mostly) seen, driver_register causes this call sequence:
-> bus_add_driver
-> module_add_driver
-> module_create_drivers_dir
The last one creates "drivers" directory in /sys/module/<...>. When
this is done in parallel, the directory is attempted to be created
twice at the same time.
This can be easily reproduced by loading mxb and hexium_gemini in
parallel:
while :; do
modprobe mxb &
modprobe hexium_gemini
wait
rmmod mxb hexium_gemini saa7146_vv saa7146
done
saa7146 calls pci_register_driver for both mxb and hexium_gemini,
which means /sys/module/saa7146/drivers is to be created for both of
them.
Fix this by a new mutex in module_create_drivers_dir which makes the
test-and-create "drivers" dir atomic.
I inverted the condition and removed 'return' to avoid multiple
unlocks or a goto.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Fixes: fe480a2675ed (Modules: only add drivers/ direcory if needed) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a task uses a non constant string for the format parameter in
trace_printk(), then the trace_printk_fmt variable is set to NULL. This
variable is then saved in the __trace_printk_fmt section.
The function hold_module_trace_bprintk_format() checks to see if duplicate
formats are used by modules, and reuses them if so (saves them to the list
if it is new). But this function calls lookup_format() that does a strcmp()
to the value (which is now NULL) and can cause a kernel oops.
This wasn't an issue till 3debb0a9ddb ("tracing: Fix trace_printk() to print
when not using bprintk()") which added "__used" to the trace_printk_fmt
variable, and before that, the kernel simply optimized it out (no NULL value
was saved).
The fix is simply to handle the NULL pointer in lookup_format() and have the
caller ignore the value if it was NULL.
Link: http://lkml.kernel.org/r/1464769870-18344-1-git-send-email-zhengjun.xing@intel.com Reported-by: xingzhen <zhengjun.xing@intel.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Fixes: 3debb0a9ddb ("tracing: Fix trace_printk() to print when not using bprintk()") Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usage Confidence is mandary to Windows Precision Touchpad devices. If
it is examined in input_mapping on a WIndows Precision Touchpad, a new add
quirk MT_QUIRK_CONFIDENCE desgned for such devices will be applied to the
device. A touch with the confidence bit is not set is determined as
invalid.
Tested on Dell XPS13 9343
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Tested-by: Andy Lutomirski <luto@kernel.org> # XPS 13 9350, BIOS 1.4.3 Signed-off-by: Allen Hung <allen_hung@dell.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 25a84db15b3f ("HID: multitouch: enable palm rejection
if device implements confidence usage")
The commit enables palm rejection for Win8 Precision Touchpad devices but
the quirk MT_QUIRK_VALID_IS_CONFIDENCE it is using is not working very
properly. This quirk is originally designed for some WIn7 touchscreens. Use
of this for a Win8 Precision Touchpad will cause unexpected pointer jumping
problem.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Tested-by: Andy Lutomirski <luto@kernel.org> # XPS 13 9350, BIOS 1.4.3 Signed-off-by: Allen Hung <allen_hung@dell.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch validates the num_values parameter from userland during the
HIDIOCGUSAGES and HIDIOCSUSAGES commands. Previously, if the report id was set
to HID_REPORT_ID_UNKNOWN, we would fail to validate the num_values parameter
leading to a heap overflow.
Flushing a work that reschedules itself is not a sensible operation. It needs
to be killed. Failure to do so leads to a kernel panic in the timer code.
Signed-off-by: Oliver Neukum <ONeukum@suse.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tracing my host KVM showed it was the one injecting the GP(0) when
emulating the VMREAD and checking the destination segment permissions in
get_vmx_mem_address():
3) | vmx_handle_exit() {
3) | handle_vmread() {
3) | nested_vmx_check_permission() {
3) | vmx_get_segment() {
3) 0.074 us | vmx_read_guest_seg_base();
3) 0.065 us | vmx_read_guest_seg_selector();
3) 0.066 us | vmx_read_guest_seg_ar();
3) 1.636 us | }
3) 0.058 us | vmx_get_rflags();
3) 0.062 us | vmx_read_guest_seg_ar();
3) 3.469 us | }
3) | vmx_get_cs_db_l_bits() {
3) 0.058 us | vmx_read_guest_seg_ar();
3) 0.662 us | }
3) | get_vmx_mem_address() {
3) 0.068 us | vmx_cache_reg();
3) | vmx_get_segment() {
3) 0.074 us | vmx_read_guest_seg_base();
3) 0.068 us | vmx_read_guest_seg_selector();
3) 0.071 us | vmx_read_guest_seg_ar();
3) 1.756 us | }
3) | kvm_queue_exception_e() {
3) 0.066 us | kvm_multiple_exception();
3) 0.684 us | }
3) 4.085 us | }
3) 9.833 us | }
3) + 10.366 us | }
Cross-checking the KVM/VMX VMREAD emulation code with the Intel Software
Developper Manual Volume 3C - "VMREAD - Read Field from Virtual-Machine
Control Structure", I found that we're enforcing that the destination
operand is NOT located in a read-only data segment or any code segment when
the L1 is in long mode - BUT that check should only happen when it is in
protected mode.
Shuffling the code a bit to make our emulation follow the specification
allows me to boot a Xen dom0 in a nested KVM and start HVM L2 guests
without problems.
Fixes: f9eb4af67c9d ("KVM: nVMX: VMX instructions: add checks for #GP/#SS exceptions") Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com> Cc: Eugene Korenevsky <ekorenevsky@gmail.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e133ab296f ("s390/mm: split arch/s390/mm/pgtable.c") factored
out the page table handling code from __gmap_zap and __s390_reset_cmma
into ptep_zap_unused and added a simple flag that tells which one of the
function (reset or not) is to be made. This also changed the behaviour,
as it also zaps unused page table entries on reset.
Turns out that this is wrong as s390_reset_cmma uses the page walker,
which DOES NOT take the ptl lock.
The most simple fix is to not do the zapping part on reset (which uses
the walker)
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Fixes: 1e133ab296f ("s390/mm: split arch/s390/mm/pgtable.c") Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VT-d posted interrupt is relying on the CPU side's posted interrupt.
Need to check whether VCPU's APICv is active before enabing VT-d
posted interrupt.
Fixes: d62caabb41f33d96333f9ef15e09cd26e1c12760 Signed-off-by: Yang Zhang <yang.zhang.wz@gmail.com> Signed-off-by: Shengge Ding <shengge.dsg@alibaba-inc.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If __key_link_begin() failed then "edit" would be uninitialized. I've
added a check to fix that.
This allows a random user to crash the kernel, though it's quite
difficult to achieve. There are three ways it can be done as the user
would have to cause an error to occur in __key_link():
(1) Cause the kernel to run out of memory. In practice, this is difficult
to achieve without ENOMEM cropping up elsewhere and aborting the
attempt.
(2) Revoke the destination keyring between the keyring ID being looked up
and it being tested for revocation. In practice, this is difficult to
time correctly because the KEYCTL_REJECT function can only be used
from the request-key upcall process. Further, users can only make use
of what's in /sbin/request-key.conf, though this does including a
rejection debugging test - which means that the destination keyring
has to be the caller's session keyring in practice.
(3) Have just enough key quota available to create a key, a new session
keyring for the upcall and a link in the session keyring, but not then
sufficient quota to create a link in the nominated destination keyring
so that it fails with EDQUOT.
The bug can be triggered using option (3) above using something like the
following:
echo 80 >/proc/sys/kernel/keys/root_maxbytes
keyctl request2 user debug:fred negate @t
The above sets the quota to something much lower (80) to make the bug
easier to trigger, but this is dependent on the system. Note also that
the name of the keyring created contains a random number that may be
between 1 and 10 characters in size, so may throw the test off by
changing the amount of quota used.
Assuming the failure occurs, something like the following will be seen:
It was first reported and reproduced by Petr (thanks!) in
https://bugzilla.kernel.org/show_bug.cgi?id=119581
free_percpu(rt->rt6i_pcpu) used to always happen in ip6_dst_destroy().
However, after fixing a deadlock bug in
commit 9c7370a166b4 ("ipv6: Fix a potential deadlock when creating pcpu rt"),
free_percpu() is not called before setting non_pcpu_rt->rt6i_pcpu to NULL.
It is worth to note that rt6i_pcpu is protected by table->tb6_lock.
kmemleak somehow did not report it. We nailed it down by
observing the pcpu entries in /proc/vmallocinfo (first suggested
by Hannes, thanks!).
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Fixes: 9c7370a166b4 ("ipv6: Fix a potential deadlock when creating pcpu rt") Reported-by: Petr Novopashenniy <pety@rusnet.ru> Tested-by: Petr Novopashenniy <pety@rusnet.ru> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Petr Novopashenniy <pety@rusnet.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several Lenovo users have reported problems with their Sierra
Wireless EM7455 modem. The driver has loaded successfully and
the MBIM management channel has appeared to work, including
establishing a connection to the mobile network. But no frames
have been received over the data interface.
The problem affects all EM7455 and MC7455, and is assumed to
affect other modems based on the same Qualcomm chipset and
baseband firmware.
Testing narrowed the problem down to what seems to be a
firmware timing bug during initialization. Adding a short sleep
while probing is sufficient to make the problem disappear.
Experiments have shown that 1-2 ms is too little to have any
effect, while 10-20 ms is enough to reliably succeed.
Reported-by: Stefan Armbruster <ml001@armbruster-it.de> Reported-by: Ralph Plawetzki <ralph@purejava.org> Reported-by: Andreas Fett <andreas.fett@secunet.com> Reported-by: Rasmus Lerdorf <rasmus@lerdorf.com> Reported-by: Samo Ratnik <samo.ratnik@gmail.com> Reported-and-tested-by: Aleksander Morgado <aleksander@aleksander.es> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For ipv6+udp+geneve encapsulation data, the max_mtu should subtract
sizeof(ipv6hdr), instead of sizeof(iphdr).
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid recursions of dev_queue_xmit() to the wrong net device when
frames are unprotected, since at that time skb->dev still points to
our own macsec dev and unlike macsec_encrypt_finish() dev pointer
doesn't get updated to real underlying device.
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to commit 9b368814b336 ("net: fix bridge multicast packet checksum validation")
we need to fixup the checksum for CHECKSUM_COMPLETE when
pushing skb on RX path. Otherwise we get similar splats.
Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
People who use PACKET_FANOUT_HASH want a symmetric hash, meaning that
they want packets going in both directions on a flow to hash to the
same bucket.
The core kernel SKB hash became non-symmetric when the ipv6 flow label
and other entities were incorporated into the standard flow hash order
to increase entropy.
But there are no users of PACKET_FANOUT_HASH who want an assymetric
hash, they all want a symmetric one.
Therefore, use the flow dissector to compute a flat symmetric hash
over only the protocol, addresses and ports. This hash does not get
installed into and override the normal skb hash, so this change has
no effect whatsoever on the rest of the stack.
Reported-by: Eric Leblond <eric@regit.org> Tested-by: Eric Leblond <eric@regit.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So I _should_ have looked at other unserialized users of ->load_avg,
but alas. Luckily nikbor reported a similar /0 from task_h_load() which
instantly triggered recollection of this here problem.
Aside from the intermediate value hitting memory and causing problems,
there's another problem: the underflow detection relies on the signed
bit. This reduces the effective width of the variables, IOW its
effectively the same as having these variables be of signed type.
This patch changes to a different means of unsigned underflow
detection to not rely on the signed bit. This allows the variables to
use the 'full' unsigned range. And it does so with explicit LOAD -
STORE to ensure any intermediate value will never be visible in
memory, allowing these unserialized loads.
Note: GCC generates crap code for this, might warrant a look later.
Note2: I say 'full' above, if we end up at U*_MAX we'll still explode;
maybe we should do clamping on add too.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Yuyang Du <yuyang.du@intel.com> Cc: bsegall@google.com Cc: kernel@kyup.com Cc: morten.rasmussen@arm.com Cc: pjt@google.com Cc: steve.muckle@linaro.org Fixes: 9d89c257dfb9 ("sched/fair: Rewrite runnable load and utilization average tracking") Link: http://lkml.kernel.org/r/20160617091948.GJ30927@twins.programming.kicks-ass.net Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During page migrations UBIFS might get confused
and the following assert triggers:
[ 213.480000] UBIFS assert failed in ubifs_set_page_dirty at 1451 (pid 436)
[ 213.490000] CPU: 0 PID: 436 Comm: drm-stress-test Not tainted 4.4.4-00176-geaa802524636-dirty #1008
[ 213.490000] Hardware name: Allwinner sun4i/sun5i Families
[ 213.490000] [<c0015e70>] (unwind_backtrace) from [<c0012cdc>] (show_stack+0x10/0x14)
[ 213.490000] [<c0012cdc>] (show_stack) from [<c02ad834>] (dump_stack+0x8c/0xa0)
[ 213.490000] [<c02ad834>] (dump_stack) from [<c0236ee8>] (ubifs_set_page_dirty+0x44/0x50)
[ 213.490000] [<c0236ee8>] (ubifs_set_page_dirty) from [<c00fa0bc>] (try_to_unmap_one+0x10c/0x3a8)
[ 213.490000] [<c00fa0bc>] (try_to_unmap_one) from [<c00fadb4>] (rmap_walk+0xb4/0x290)
[ 213.490000] [<c00fadb4>] (rmap_walk) from [<c00fb1bc>] (try_to_unmap+0x64/0x80)
[ 213.490000] [<c00fb1bc>] (try_to_unmap) from [<c010dc28>] (migrate_pages+0x328/0x7a0)
[ 213.490000] [<c010dc28>] (migrate_pages) from [<c00d0cb0>] (alloc_contig_range+0x168/0x2f4)
[ 213.490000] [<c00d0cb0>] (alloc_contig_range) from [<c010ec00>] (cma_alloc+0x170/0x2c0)
[ 213.490000] [<c010ec00>] (cma_alloc) from [<c001a958>] (__alloc_from_contiguous+0x38/0xd8)
[ 213.490000] [<c001a958>] (__alloc_from_contiguous) from [<c001ad44>] (__dma_alloc+0x23c/0x274)
[ 213.490000] [<c001ad44>] (__dma_alloc) from [<c001ae08>] (arm_dma_alloc+0x54/0x5c)
[ 213.490000] [<c001ae08>] (arm_dma_alloc) from [<c035cecc>] (drm_gem_cma_create+0xb8/0xf0)
[ 213.490000] [<c035cecc>] (drm_gem_cma_create) from [<c035cf20>] (drm_gem_cma_create_with_handle+0x1c/0xe8)
[ 213.490000] [<c035cf20>] (drm_gem_cma_create_with_handle) from [<c035d088>] (drm_gem_cma_dumb_create+0x3c/0x48)
[ 213.490000] [<c035d088>] (drm_gem_cma_dumb_create) from [<c0341ed8>] (drm_ioctl+0x12c/0x444)
[ 213.490000] [<c0341ed8>] (drm_ioctl) from [<c0121adc>] (do_vfs_ioctl+0x3f4/0x614)
[ 213.490000] [<c0121adc>] (do_vfs_ioctl) from [<c0121d30>] (SyS_ioctl+0x34/0x5c)
[ 213.490000] [<c0121d30>] (SyS_ioctl) from [<c000f2c0>] (ret_fast_syscall+0x0/0x34)
UBIFS is using PagePrivate() which can have different meanings across
filesystems. Therefore the generic page migration code cannot handle this
case correctly.
We have to implement our own migration function which basically does a
plain copy but also duplicates the page private flag.
UBIFS is not a block device filesystem and cannot use buffer_migrate_page().
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[rw: Massaged changelog, build fixes, etc...] Signed-off-by: Richard Weinberger <richard@nod.at> Acked-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When allocating a new device IRQ, gic_dev_domain_alloc() correctly calls
irq_domain_set_hwirq_and_chip(), but gic_irq_domain_alloc() does not. This
means that gic_irq_domain believes all IRQs from the dev domain have an
hwirq of 0 and creates incorrect mappings in the linear_revmap. As
gic_irq_domain is a parent of the gic_dev_domain, this leads to an
inability to boot on devices with a GIC. Excerpt of the error:
Copy __kvm_mips_vcpu_run() into unmapped memory, so that we can never
get a TLB refill exception in it when KVM is built as a module.
This was observed to happen with the host MIPS kernel running under
QEMU, due to a not entirely transparent optimisation in the QEMU TLB
handling where TLB entries replaced with TLBWR are copied to a separate
part of the TLB array. Code in those pages continue to be executable,
but those mappings persist only until the next ASID switch, even if they
are marked global.
An ASID switch happens in __kvm_mips_vcpu_run() at exception level after
switching to the guest exception base. Subsequent TLB mapped kernel
instructions just prior to switching to the guest trigger a TLB refill
exception, which enters the guest exception handlers without updating
EPC. This appears as a guest triggered TLB refill on a host kernel
mapped (host KSeg2) address, which is not handled correctly as user
(guest) mode accesses to kernel (host) segments always generate address
error exceptions.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: kvm@vger.kernel.org Cc: linux-mips@linux-mips.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the same issue fixed in commit dcf5341f0150 ("ARM: dts:
sun8i-q8-common: Do not set constraints on dc1sw regulator").
Commit message copied:
dc1sw is an on/off only regulator and as such it cannot have constraints.
This is a limitation of the kernel regulator implementation which resolves
supplies on the first regulator_get(), which is done after applying
constraints, and applying the constrains will fail because it calls
_regulator_get_voltage() and _regulator_do_set_voltage() both of which
will fail on a switch regulator when there is no supply (yet).
This causes registering of all axp22x regulators to fail with the
following errors:
[ 1.395249] vcc-lcd: failed to get the current voltage(-22)
[ 1.405131] axp20x-regulator axp20x-regulator: Failed to register dc1sw
[ 1.412436] axp20x-regulator: probe of axp20x-regulator failed with error -22
This commit removes the constrains on dc1sw / vcc-lcd fixing this problem.
Note that dcdc1 itself is contrained to the exact same values, so this
does not change anything.
Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the same issue fixed in commit dcf5341f0150 ("ARM: dts:
sun8i-q8-common: Do not set constraints on dc1sw regulator").
Commit message copied:
dc1sw is an on/off only regulator and as such it cannot have constraints.
This is a limitation of the kernel regulator implementation which resolves
supplies on the first regulator_get(), which is done after applying
constraints, and applying the constrains will fail because it calls
_regulator_get_voltage() and _regulator_do_set_voltage() both of which
will fail on a switch regulator when there is no supply (yet).
This causes registering of all axp22x regulators to fail with the
following errors:
[ 1.395249] vcc-lcd: failed to get the current voltage(-22)
[ 1.405131] axp20x-regulator axp20x-regulator: Failed to register dc1sw
[ 1.412436] axp20x-regulator: probe of axp20x-regulator failed with error -22
This commit removes the constrains on dc1sw / vcc-lcd fixing this problem.
Note that dcdc1 itself is contrained to the exact same values, so this
does not change anything.
Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently pmd_mknotpresent will use a zero entry to respresent an
invalidated pmd.
Unfortunately this definition clashes with pmd_none, thus it is
possible for a race condition to occur if zap_pmd_range sees pmd_none
whilst __split_huge_pmd_locked is running too with pmdp_invalidate
just called.
This patch fixes the race condition by modifying pmd_mknotpresent to
create non-zero faulting entries (as is done in other architectures),
removing the ambiguity with pmd_none.
[catalin.marinas@arm.com: using L_PMD_SECT_VALID instead of PMD_TYPE_SECT]
Fixes: 8d9625070073 ("ARM: mm: Transparent huge page support for LPAE systems.") Reported-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Russell King <linux@armlinux.org.uk> Signed-off-by: Steve Capper <steve.capper@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a subsequent patch, pmd_mknotpresent will clear the valid bit of the
pmd entry, resulting in a not-present entry from the hardware's
perspective. Unfortunately, pmd_present simply checks for a non-zero pmd
value and will therefore continue to return true even after a
pmd_mknotpresent operation. Since pmd_mknotpresent is only used for
managing huge entries, this is only an issue for the 3-level case.
This patch fixes the 3-level pmd_present implementation to take into
account the valid bit. For bisectability, the change is made before the
fix to pmd_mknotpresent.
Fixes: 8d9625070073 ("ARM: mm: Transparent huge page support for LPAE systems.") Cc: Russell King <linux@armlinux.org.uk> Cc: Steve Capper <Steve.Capper@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After "regulator: qcom_smd: add list_voltage callback" patch adding
pm8941 lnldo regulators would bug on list_voltages as it is a fixed
regulator without any linear range.
This patch fixes that issue by adding dedicated ops for pm8941 lnldo
without list_voltages callback.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The spec allows backchannels for multiple clients to share the same tcp
connection. When that happens, we need to use the same xprt for all of
them. Similarly, we need the same xps.
This fixes list corruption introduced by the multipath code.
Signed-off-by: J. Bruce Fields <bfields@redhat.com> Acked-by: Trond Myklebust <trondmy@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Olga Kornievskaia reports that the following test fails to trigger
an OPEN_DOWNGRADE on the wire, and only triggers the final CLOSE.
fd0 = open(foo, RDRW) -- should be open on the wire for "both"
fd1 = open(foo, RDONLY) -- should be open on the wire for "read"
close(fd0) -- should trigger an open_downgrade
read(fd1)
close(fd1)
The issue is that we're missing a check for whether or not the current
state transitioned from an O_RDWR state as opposed to having transitioned
from a combination of O_RDONLY and O_WRONLY.
Reported-by: Olga Kornievskaia <aglo@umich.edu> Fixes: cd9288ffaea4 ("NFSv4: Fix another bug in the close/open_downgrade code") Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In "NFSv4: Move dentry instantiation into the NFSv4-specific atomic open code"
unconditional d_drop() after the ->open_context() had been removed. It had
been correct for success cases (there ->open_context() itself had been doing
dcache manipulations), but not for error ones. Only one of those (ENOENT)
got a compensatory d_drop() added in that commit, but in fact it should've
been done for all errors. As it is, the case of O_CREAT non-exclusive open
on a hashed negative dentry racing with e.g. symlink creation from another
client ended up with ->open_context() getting an error and proceeding to
call nfs_lookup(). On a hashed dentry, which would've instantly triggered
BUG_ON() in d_materialise_unique() (or, these days, its equivalent in
d_splice_alias()).
Tested-by: Oleg Drokin <green@linuxhacker.ru> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pnfs_generic_commit_cancel_empty_pagelist calls nfs_commitdata_release,
but that is wrong: nfs_commitdata_release puts the open context, something
that isn't valid until nfs_init_commit is called, which is never the case
when pnfs_generic_commit_cancel_empty_pagelist is called.
This was introduced in "nfs: avoid race that crashes nfs_init_commit".
Use set_posix_acl, which includes proper permission checks, instead of
calling ->set_acl directly. Without this anyone may be able to grant
themselves permissions to a file by setting the ACL.
Lock the inode to make the new checks atomic with respect to set_acl.
(Also, nfsd was the only caller of set_acl not locking the inode, so I
suspect this may fix other races.)
This also simplifies the code, and ensures our ACLs are checked by
posix_acl_valid.
The permission checks and the inode locking were lost with commit 4ac7249e, which changed nfsd to use the set_acl inode operation directly
instead of going through xattr handlers.
Reported-by: David Sinquin <david@sinquin.eu>
[agreunba@redhat.com: use set_posix_acl] Fixes: 4ac7249e Cc: Christoph Hellwig <hch@infradead.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factor out part of posix_acl_xattr_set into a common function that takes
a posix_acl, which nfsd can also call.
The prototype already exists in include/linux/posix_acl.h.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It used to be the case that state had an rwlock that was locked for write
by downgrades, but for read for upgrades (opens). Well, the problem is
if there are two competing opens for the same state, they step on
each other toes potentially leading to leaking file descriptors
from the state structure, since access mode is a bitmap only set once.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For historic reasons, io_opt is in bytes and max_sectors in block layer
sectors. This interface inconsistency is error prone and should be
fixed. But for 4.4--4.7 let's make the unit difference explicit via a
wrapper function.
Fixes: d0eb20a863ba ("sd: Optimal I/O size is in bytes, not sectors") Reported-by: Fam Zheng <famz@redhat.com> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Tested-by: Andrew Patterson <andrew.patterson@hpe.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As vm.dirty_[background_]bytes can't be applied verbatim to multiple
cgroup writeback domains, they get converted to percentages in
domain_dirty_limits() and applied the same way as
vm.dirty_[background]ratio. However, if the specified bytes is lower
than 1% of available memory, the calculated ratios become zero and the
writeback domain gets throttled constantly.
Fix it by using per-PAGE_SIZE instead of percentage for ratio
calculations. Also, the updated DIV_ROUND_UP() usages now should
yield 1/4096 (0.0244%) as the minimum ratio as long as the specified
bytes are above zero.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Miao Xie <miaoxie@huawei.com> Link: http://lkml.kernel.org/g/57333E75.3080309@huawei.com Fixes: 9fc3a43e1757 ("writeback: separate out domain_dirty_limits()") Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjusted comment based on Jan's suggestion. Signed-off-by: Jens Axboe <axboe@fb.com>
The freq_table array is not populated before calling
thermal_of_cooling_register. The code which populates the freq table was
introduced in commit f6859014.
This should be done before registering new thermal cooling device.
The log shows effects of this wrong decision.
[ 2.172614] cpu cpu1: Failed to get voltage for frequency 1984518656000: -34
[ 2.220863] cpu cpu0: Failed to get voltage for frequency 1984524416000: -34
Fixes: f6859014c7e7 ("thermal: cpu_cooling: Store frequencies in descending order") Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> Acked-by: Javi Merino <javi.merino@arm.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 49f86ec21c01 ("rtlwifi: Change long delays to sleeps") was correct
for most cases; however, driver rtl8192ce calls the affected routines while
in atomic context. The kernel bug output is as follows:
To fix this bug, three of the changes from delay to sleep are reverted.
Unfortunately, one of the changes involves a delay of 50 msec. The calling
code will be modified so that this long delay can be avoided; however,
this change is being pushed now to fix the problem in kernel 4.6.0.
Fixes: 49f86ec21c01 ("rtlwifi: Change long delays to sleeps") Reported-by: James Feeney <james@nurealm.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: James Feeney <james@nurealm.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's an analogue of commit 7500c38a (fix the braino in "namei:
massage lookup_slow() to be usable by lookup_one_len_unlocked()").
The same problem (->lookup()-returned unhashed negative dentry
just might be an autofs one with ->d_manage() that would wait
until the daemon makes it positive) applies in do_last() - we
need to do follow_managed() first.
Fortunately, remaining callers of follow_managed() are OK - only
autofs has that weirdness (negative dentry that does not mean
an instant -ENOENT)) and autofs never has its negative dentries
hashed, so we can't pick one from a dcache lookup.
->d_manage() is a bloody mess ;-/
Spotted-by: Ian Kent <raven@themaw.net> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure consumers do not overwrite gpio flags for pins that have
already been claimed.
While adding support for gpio drivers to refuse a request using
unsupported flags, the order of when the requested flag was checked and
the new flags were applied was reversed to that consumers could
overwrite flags for already requested gpios.
This not only affects device-tree setups where two drivers could request
the same gpio using conflicting configurations, but also allowed user
space to clear gpio flags for already claimed pins simply by attempting
to export them through the sysfs interface. By for example clearing the
FLAG_ACTIVE_LOW flag this way, user space could effectively change the
polarity of a signal.
Reverting this change obviously prevents gpio drivers from doing sanity
checks on the flags in their request callbacks. Fortunately only one
recently added driver (gpio-tps65218 in v4.6) appears to do this, and a
follow up patch could restore this functionality through a different
interface.
This fixes the issue descirbe in bug 117531
(https://bugzilla.kernel.org/show_bug.cgi?id=117531).
It's a regression introduced in linux 4.5 that causes a Oops at load of
gpio_sch and prevents powering off the computer.
The issue is that sch_gpio_reg_set is called in sch_gpio_probe before
gpio_chip data is initialized with the pointer to the sch_gpio struct. As
sch_gpio_reg_set calls gpiochip_get_data, it returns NULL which causes
the Oops.
The patch follows Mika's advice (https://lkml.org/lkml/2016/5/9/61) and
consists in modifying sch_gpio_reg_get and sch_gpio_reg_set to take a
sch_gpio struct directly instead of a gpio_chip, which avoids the call to
gpiochip_get_data.
Thanks Mika for your patience with me :-)
Signed-off-by: Colin Pitrat <colin.pitrat@gmail.com> Acked-by: Alexandre Courbot <acourbot@nvidia.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most functions that take a GPIO descriptor in need to check the
descriptor for IS_ERR(). We do this mostly in the VALIDATE_DESC()
macro except for the gpiod_to_irq() function which needs special
handling.
If USB cable is connected prior to boot, we don't get any interrupts
so we must manually check the VBUS state and report it during probe.
If we don't do it then USB controller will never know that peripheral
cable was connected till the user unplugs and replugs the cable.
Fixes: b7aad8e2685b ("extcon: palmas: Add the support for VBUS detection by using GPIO") Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix boot crash that triggers if this driver is built into a kernel and
run on non-AMD systems.
AMD northbridges users call amd_cache_northbridges() and it returns
a negative value to signal that we weren't able to cache/detect any
northbridges on the system.
At least, it should do so as all its callers expect it to do so. But it
does return a negative value only when kmalloc() fails.
Fix it to return -ENODEV if there are no NBs cached as otherwise, amd_nb
users like amd64_edac, for example, which relies on it to know whether
it should load or not, gets loaded on systems like Intel Xeons where it
shouldn't.
On rapl cleanup path, kfree() is given by mistake the address of the
pointer of the structure to free (rapl_pmus->pmus + i). Pass the pointer
instead (rapl_pmus->pmus[i]).
Fixes: 9de8d686955b "perf/x86/intel/rapl: Convert it to a per package facility" Signed-off-by: Vincent Stehlé <vincent.stehle@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1464101629-14905-1-git-send-email-vincent.stehle@intel.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix kprobe_fault_handler() to clear the TF (trap flag) bit of
the flags register in the case of a fault fixup on single-stepping.
If we put a kprobe on the instruction which caused a
page fault (e.g. actual mov instructions in copy_user_*),
that fault happens on the single-stepping buffer. In this
case, kprobes resets running instance so that the CPU can
retry execution on the original ip address.
However, current code forgets to reset the TF bit. Since this
fault happens with TF bit set for enabling single-stepping,
when it retries, it causes a debug exception and kprobes
can not handle it because it already reset itself.
On the most of x86-64 platform, it can be easily reproduced
by using kprobe tracer. E.g.
# cd /sys/kernel/debug/tracing
# echo p copy_user_enhanced_fast_string+5 > kprobe_events
# echo 1 > events/kprobes/enable
And you'll see a kernel panic on do_debug(), since the debug
trap is not handled by kprobes.
To fix this problem, we just need to clear the TF bit when
resetting running kprobe.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Reviewed-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com> Acked-by: Steven Rostedt <rostedt@goodmis.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: systemtap@sourceware.org Link: http://lkml.kernel.org/r/20160611140648.25885.37482.stgit@devbox
[ Updated the comments. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For newer versions of Syslinux, we need ldlinux.c32 in addition to
isolinux.bin to reside on the boot disk, so if the latter is found,
copy it, too, to the isoimage tree.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cpuidle_devices per-CPU variable is only defined when CPU_IDLE is
enabled. Commit c8cc7d4de7a4 ("sched/idle: Reorganize the idle loop")
removed the #ifdef CONFIG_CPU_IDLE around cpuidle_idle_call() with the
compiler optimising away __this_cpu_read(cpuidle_devices). However, with
CONFIG_UBSAN && !CONFIG_CPU_IDLE, this optimisation no longer happens
and the kernel fails to link since cpuidle_devices is not defined.
This patch introduces an accessor function for the current CPU cpuidle
device (returning NULL when !CONFIG_CPU_IDLE) and uses it in
cpuidle_idle_call().
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CPU 1 CPU 2
static_key_slow_inc()
atomic_inc_not_zero()
-> key.enabled == 0, no increment
jump_label_lock()
atomic_inc_return()
-> key.enabled == 1 now
static_key_slow_inc()
atomic_inc_not_zero()
-> key.enabled == 1, inc to 2
return
** static key is wrong!
jump_label_update()
jump_label_unlock()
Testing the static key at the point marked by (**) will follow the
wrong path for jumps that have not been patched yet. This can
actually happen when creating many KVM virtual machines with userspace
LAPIC emulation; just run several copies of the following program:
int main(void)
{
for (;;) {
int kvmfd = open("/dev/kvm", O_RDONLY);
int vmfd = ioctl(kvmfd, KVM_CREATE_VM, 0);
close(ioctl(vmfd, KVM_CREATE_VCPU, 1));
close(vmfd);
close(kvmfd);
}
return 0;
}
Every KVM_CREATE_VCPU ioctl will attempt a static_key_slow_inc() call.
The static key's purpose is to skip NULL pointer checks and indeed one
of the processes eventually dereferences NULL.
As explained in the commit that introduced the bug:
jump_label_update() needs key.enabled to be true. The solution adopted
here is to temporarily make key.enabled == -1, and use go down the
slow path when key.enabled <= 0.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 706249c222f6 ("locking/static_keys: Rework update logic") Link: http://lkml.kernel.org/r/1466527937-69798-1-git-send-email-pbonzini@redhat.com
[ Small stylistic edits to the changelog and the code. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
54cf809b9512 ("locking,qspinlock: Fix spin_is_locked() and spin_unlock_wait()")
... fixes spin_is_locked() and spin_unlock_wait() for the usage
in ipc/sem and netfilter, it does not in fact work right for the
usage in task_work and futex.
So while the 2 locks crossed problem:
spin_lock(A) spin_lock(B)
if (!spin_is_locked(B)) spin_unlock_wait(A)
foo() foo();
... works with the smp_mb() injected by both spin_is_locked() and
spin_unlock_wait(), this is not sufficient for:
flag = 1;
smp_mb(); spin_lock()
spin_unlock_wait() if (!flag)
// add to lockless list
// iterate lockless list
... because in this scenario, the store from spin_lock() can be delayed
past the load of flag, uncrossing the variables and loosing the
guarantee.
This patch reworks spin_is_locked() and spin_unlock_wait() to work in
both cases by exploiting the observation that while the lock byte
store can be delayed, the contender must have registered itself
visibly in other state contained in the word.
It also allows for architectures to override both functions, as PPC
and ARM64 have an additional issue for which we currently have no
generic solution.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Giovanni Gherdovich <ggherdovich@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Pan Xinhui <xinhui.pan@linux.vnet.ibm.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Waiman Long <waiman.long@hpe.com> Cc: Will Deacon <will.deacon@arm.com> Fixes: 54cf809b9512 ("locking,qspinlock: Fix spin_is_locked() and spin_unlock_wait()") Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recursive locking for ww_mutexes was originally conceived as an
exception. However, it is heavily used by the DRM atomic modesetting
code. Currently, the recursive deadlock is checked after we have queued
up for a busy-spin and as we never release the lock, we spin until
kicked, whereupon the deadlock is discovered and reported.
A simple solution for the now common problem is to move the recursive
deadlock discovery to the first action when taking the ww_mutex.
Suggested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1464293297-19777-1-git-send-email-chris@chris-wilson.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The msr tracing for writes is incorrectly conditional on the read trace.
Fixes: 7f47d8cc039f "x86, tracing, perf: Add trace point for MSR accesses" Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com> Cc: ak@linux.intel.com Link: http://lkml.kernel.org/r/1464976859-21850-1-git-send-email-dgilbert@redhat.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel-doc for the of_irq_get[_byname]() is clearly inadequate in
describing the return values -- of_irq_get_byname() is documented better
than of_irq_get() but it still doesn't mention that 0 is returned iff
irq_create_of_mapping() fails (it doesn't return an error code in this
case). Document all possible return value variants, making the writing
of the word "IRQ" consistent, while at it...
Fixes: 9ec36cafe43b ("of/irq: do irq resolution in platform_get_irq") Fixes: ad69674e73a1 ("of/irq: do irq resolution in platform_get_irq_byname()") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
