'ret' is known to be 1 here. In fact 'i' is expected instead.
Store the return value of 'i2c_master_recv()' in 'ret' so that the error
message print the correct error code.
EVM_SETUP_COMPLETE is defined as 0x80000000, which is larger than INT_MAX.
The "-fno-strict-overflow" compiler option properly prevents signaling
EVM that the EVM policy setup is complete. Define and read an unsigned
int.
Fixes: f00d79750712 ("EVM: Allow userspace to signal an RSA key has been loaded") Signed-off-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Iff platform_get_irq() fails (or returns IRQ0) and thus the polling mode
has to be used, ata_host_activate() hits the WARN_ON() due to 'irq_handler'
parameter being non-NULL if the polling mode is selected. Let's only set
the pointer to the driver's IRQ handler if platform_get_irq() returns a
valid IRQ # -- this should avoid the unnecessary WARN_ON()...
The use of an enum named 'RST' conflicts with a #define macro
named 'RST' in arch/mips/include/asm/mach-rc32434/rb.h.
The MIPS use of RST was there first (AFAICT), so change the
media/i2c/ uses of RST to be named 'RSET'.
'git grep -w RSET' does not report any naming conflicts with the
new name.
This fixes multiple build errors:
arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
drivers/media/i2c/s5c73m3/s5c73m3.h:356:2: note: in expansion of macro 'RST'
356 | RST,
| ^~~
../arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
../drivers/media/i2c/s5k6aa.c:180:2: note: in expansion of macro 'RST'
180 | RST,
| ^~~
../arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
../drivers/media/i2c/s5k5baf.c:238:2: note: in expansion of macro 'RST'
238 | RST,
| ^~~
and some others that I have trimmed.
Fixes: cac47f1822fc ("[media] V4L: Add S5C73M3 camera driver") Fixes: 8b99312b7214 ("[media] Add v4l2 subdev driver for S5K4ECGX sensor") Fixes: 7d459937dc09 ("[media] Add driver for Samsung S5K5BAF camera sensor") Fixes: bfa8dd3a0524 ("[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Cc: Sangwook Lee <sangwook.lee@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver overrides the error codes returned by platform_get_irq() to
-ENOENT, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Switch to propagating the
error code upstream, still checking/overriding IRQ0 as libata regards it
as "no IRQ" (thus polling) anyway...
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Switch to propagating the
error code upstream, still checking/overriding IRQ0 as libata regards it
as "no IRQ" (thus polling) anyway...
Testing ixp4xx_crypto with CONFIG_DMA_API_DEBUG lead to the following error:
DMA-API: platform ixp4xx_crypto.0: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=24 bytes]
There's a bug at s5p_cec_adap_enable(): if called to
disable the device, it should call pm_runtime_put()
instead of pm_runtime_disable(), as the goal here is to
decrement the usage_count and not to disable PM runtime.
gcc points out a mistake in the mca driver that goes back to before the
git history:
arch/ia64/kernel/mca_drv.c: In function 'init_record_index_pools':
arch/ia64/kernel/mca_drv.c:346:54: error: expression does not compute the number of elements in this array; element typ
e is 'int', not 'size_t' {aka 'long unsigned int'} [-Werror=sizeof-array-div]
346 | for (i = 1; i < sizeof sal_log_sect_min_sizes/sizeof(size_t); i++)
| ^
This is the same as sizeof(size_t), which is two shorter than the actual
array. Use the ARRAY_SIZE() macro to get the correct calculation instead.
A custom DSDT file is mostly used during development or debugging,
and in that case it is quite likely to want to rebuild the kernel
after changing ONLY the content of the DSDT.
This patch adds the custom DSDT as a prerequisite to tables.o
to ensure a rebuild if the DSDT file is updated. Make will merge
the prerequisites from multiple rules for the same target.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the clocksource watchdog marks a clock as unstable, this might be due
to that clock being unstable or it might be due to delays that happen to
occur between the reads of the two clocks. Yes, interrupts are disabled
across those two reads, but there are no shortage of things that can delay
interrupts-disabled regions of code ranging from SMI handlers to vCPU
preemption. It would be good to have some indication as to why the clock
was marked unstable.
Therefore, re-read the watchdog clock on either side of the read from the
clock under test. If the watchdog clock shows an excessive time delta
between its pair of reads, the reads are retried.
The maximum number of retries is specified by a new kernel boot parameter
clocksource.max_cswd_read_retries, which defaults to three, that is, up to
four reads, one initial and up to three retries. If more than one retry
was required, a message is printed on the console (the occasional single
retry is expected behavior, especially in guest OSes). If the maximum
number of retries is exceeded, the clock under test will be marked
unstable. However, the probability of this happening due to various sorts
of delays is quite small. In addition, the reason (clock-read delays) for
the unstable marking will be apparent.
Reported-by: Chris Mason <clm@fb.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Feng Tang <feng.tang@intel.com> Link: https://lore.kernel.org/r/20210527190124.440372-1-paulmck@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Although the system will not be in a good condition or it will not
boot if acpi_bus_init() fails, it is still necessary to put the
kobject in the error path before returning to avoid leaking memory.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the ACPI spec, _CID returns a package containing
hardware ID's. Each element of an ASL package contains a reference
count from the parent package as well as the element itself.
Name (TEST, Package() {
"String object" // this package element has a reference count of 2
})
A memory leak was caused in the _CID repair function because it did
not decrement the reference count created by the package. Fix the
memory leak by calling acpi_ut_remove_reference on _CID package elements
that represent a hardware ID (_HID).
Link: https://github.com/acpica/acpica/commit/180cb539 Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Erik Kaneda <erik.kaneda@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
I got some kmemleak report when a node was fenced. The user space tool
dlm_controld will therefore run some rmdir() in dlm configfs which was
triggering some memleaks. This patch stores the sps and cms attributes
which stores some handling for subdirectories of the configfs cluster
entry and free them if they get released as the parent directory gets
freed.
include/linux/prandom.h:114:45: sparse: sparse: cast truncates bits from
constant value
This is because the 64-bit seed value is manipulated and then placed in a
u32, causing an implicit cast and truncation. A forced cast to u32 doesn't
prevent this warning, which is reasonable because a typecast doesn't prove
that truncation was expected.
Logical-AND the value with 0xffffffff to make explicit that truncation to
32-bit is intended.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Petr Mladek <pmladek@suse.com> Link: https://lore.kernel.org/r/20210525122012.6336-3-rf@opensource.cirrus.com Signed-off-by: Sasha Levin <sashal@kernel.org>
These rx tx flags arguments are for signaling close_connection() from
which worker they are called. Obviously the receive worker cannot cancel
itself and vice versa for swork. For the othercon the receive worker
should only be used, however to avoid deadlocks we should pass the same
flags as the original close_connection() was called.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
block_dump is an old debugging interface, one of it's functions is used
to print the information about who write which file on disk. If we
enable block_dump through /proc/sys/vm/block_dump and turn on debug log
level, we can gather information about write process name, target file
name and disk from kernel message. This feature is realized in
block_dump___mark_inode_dirty(), it print above information into kernel
message directly when marking inode dirty, so it is noisy and can easily
trigger log storm. At the same time, get the dentry refcount is also not
safe, we found it will lead to deadlock on ext4 file system with
data=journal mode.
After tracepoints has been introduced into the kernel, we got a
tracepoint in __mark_inode_dirty(), which is a better replacement of
block_dump___mark_inode_dirty(). The only downside is that it only trace
the inode number and not a file name, but it probably doesn't matter
because the original printed file name in block_dump is not accurate in
some cases, and we can still find it through the inode number and device
id. So this patch delete the dirting inode part of block_dump feature.
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20210313030146.2882027-2-yi.zhang@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
More ASUS laptops have the _GPE define in the DSDT table with a
different value than the _GPE number in the ECDT.
This is causing media keys not working on ASUS X505BA/BP, X542BA/BP
Add model info to the quirks list.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com> Signed-off-by: Jian-Hong Pan <jhp@endlessos.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The existing code attempted to handle numbers by doing a strto[u]l(),
ignoring the field width, and then repeatedly dividing to extract the
field out of the full converted value. If the string contains a run of
valid digits longer than will fit in a long or long long, this would
overflow and no amount of dividing can recover the correct value.
This patch fixes vsscanf() to obey number field widths when parsing
the number.
A new _parse_integer_limit() is added that takes a limit for the number
of characters to parse. The number field conversion in vsscanf is changed
to use this new function.
If a number starts with a radix prefix, the field width must be long
enough for at last one digit after the prefix. If not, it will be handled
like this:
sscanf("0x4", "%1i", &i): i=0, scanning continues with the 'x'
sscanf("0x4", "%2i", &i): i=0, scanning continues with the '4'
This is consistent with the observed behaviour of userland sscanf.
Note that this patch does NOT fix the problem of a single field value
overflowing the target type. So for example:
Generally, the C-state latency is provided by the _CST method or
FADT, but some OEM platforms using AMD Picasso, Renoir, Van Gogh,
and Cezanne set the C2 latency greater than C3's which causes the
C2 state to be skipped.
That will block the core entering PC6, which prevents S0ix working
properly on Linux systems.
In other operating systems, the latency values are not validated and
this does not cause problems by skipping states.
To avoid this issue on Linux, detect when latencies are not an
arithmetic progression and sort them.
Action of unbinding driver from a device is not cancellable and should not
fail, and driver core does not pay attention to the result of "remove"
method, therefore using down_interruptible() in hid_device_remove() does
not make sense.
With a config having PAGE_SIZE set to 256K, BTRFS build fails
with the following message
include/linux/compiler_types.h:326:38: error: call to
'__compiletime_assert_791' declared with attribute error:
BUILD_BUG_ON failed: (BTRFS_MAX_COMPRESSED % PAGE_SIZE) != 0
BTRFS_MAX_COMPRESSED being 128K, BTRFS cannot support platforms with
256K pages at the time being.
There are two platforms that can select 256K pages:
- hexagon
- powerpc
Disable BTRFS when 256K page size is selected. Supporting this would
require changes to the subpage mode that's currently being developed.
Given that 256K is many times larger than page sizes commonly used and
for what the algorithms and structures have been tuned, it's out of
scope and disabling build is a reasonable option.
If we fail to update the delayed inode we need to abort the transaction,
because we could leave an inode with the improper counts or some other
such corruption behind.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we get an error while looking up the inode item we'll simply bail
without cleaning up the delayed node. This results in this style of
warning happening on commit:
Because the iref isn't dropped and this leaves an elevated node->count,
so any release just re-queues it onto the delayed inodes list. Fix this
by going to the out label to handle the proper cleanup of the delayed
node.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some BT.656 sensors (e.g. ADV718x) transmit frames with unstable BT.656
sync codes after initial power on. This confuses the imx CSI,resulting
in vertical and/or horizontal sync issues. Skip the first 20 frames
to avoid the unstable sync codes.
[fabio: fixed checkpatch warning and increased the frame skipping to 20]
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The risk of especulation is actually almost-non-existing here,
as there are very few users of TCP/IP using the DVB stack,
as, this is mainly used with DVB-S/S2 cards, and only by people
that receives TCP/IP from satellite connections, which limits
a lot the number of users of such feature(*).
(*) In thesis, DVB-C cards could also benefit from it, but I'm
yet to see a hardware that supports it.
crypto_shash_alg_has_setkey() is implemented by testing whether the
.setkey() member of a struct shash_alg points to the default version,
called shash_no_setkey(). As crypto_shash_alg_has_setkey() is a static
inline, this requires shash_no_setkey() to be exported to modules.
Unfortunately, when building with CFI, function pointers are routed
via CFI stubs which are private to each module (or to the kernel proper)
and so this function pointer comparison may fail spuriously.
Let's fix this by turning crypto_shash_alg_has_setkey() into an out of
line function.
Cc: Sami Tolvanen <samitolvanen@google.com> Cc: Eric Biggers <ebiggers@kernel.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Reviewed-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the driver fails to talk with the hardware with dvb_usb_generic_rw,
it will return an error to dvb_usb_adapter_frontend_init. However, the
driver forgets to free the resource (e.g., struct cinergyt2_fe_state),
which leads to a memory leak.
Fix this by freeing struct cinergyt2_fe_state when dvb_usb_generic_rw
fails in cinergyt2_frontend_attach.
When ctx_id >= HVA_MAX_INSTANCES in hva_hw_its_irq_thread() it tries to
access fields of ctx that is NULL at that point. The patch gets rid of
these accesses.
Found by Linux Driver Verification project (linuxtesting.org).
In 'bt878_irq', the driver calls 'tasklet_schedule', but this tasklet is
set in 'dvb_bt8xx_load_card' of another driver 'dvb-bt8xx'.
However, this two drivers are separate. The user may not load the
'dvb-bt8xx' driver when loading the 'bt8xx' driver, that is, the tasklet
has not been initialized when 'tasklet_schedule' is called, so it is
necessary to check whether the tasklet is initialized in 'bt878_probe'.
Fix this by adding a check at the end of bt878_probe.
When using something other than 8 spaces per tab, this ascii art
makes not sense, and the reader might end up wondering what this
advanced equation "is".
Signed-off-by: Odin Ugedal <odin@uged.al> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Vincent Guittot <vincent.guittot@linaro.org> Link: https://lkml.kernel.org/r/20210518125202.78658-4-odin@uged.al Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot has reported the following warning in pvr2_i2c_done:
sysfs group 'power' not found for kobject '1-0043'
When the device is disconnected (pvr_hdw_disconnect), the i2c adapter is
not unregistered along with the USB and v4l2 teardown. As part of the USB
device disconnect, the sysfs files of the subdevices are also deleted.
So, by the time pvr_i2c_core_done is called by pvr_context_destroy, the
sysfs files have been deleted.
To fix this, unregister the i2c adapter too in pvr_hdw_disconnect. Make
the device deregistration code shared by calling pvr_hdw_disconnect from
pvr2_hdw_destroy.
syzbot reported leak in cpia2 usb driver. The problem was
in invalid error handling.
v4l2_device_register() is called in cpia2_init_camera_struct(), but
all error cases after cpia2_init_camera_struct() did not call the
v4l2_device_unregister()
Reported-by: syzbot+d1e69c888f0d3866ead4@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Bixuan Cui <cuibixuan@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
pch_spi_set_tx() frees data->pkt_tx_buff on failure of kzalloc() for
data->pkt_rx_buff, but its caller, pch_spi_process_messages(), will
free data->pkt_tx_buff again. Set data->pkt_tx_buff to NULL after
kfree() to avoid double free.
Currently, the SPI core doesn't set the struct device fwnode pointer
when it creates a new SPI device. This means when the device is
registered the fwnode is NULL and the check in device_add which sets
the fwnode->dev pointer is skipped. This wasn't previously an issue,
however these two patches:
commit 4731210c09f5 ("gpiolib: Bind gpio_device to a driver to enable
fw_devlink=on by default")
commit ced2af419528 ("gpiolib: Don't probe gpio_device if it's not the
primary device")
Added some code to the GPIO core which relies on using that
fwnode->dev pointer to determine if a driver is bound to the fwnode
and if not bind a stub GPIO driver. This means the GPIO providers
behind SPI will get both the expected driver and this stub driver
causing the stub driver to fail if it attempts to request any pin
configuration. For example on my system:
madera-pinctrl madera-pinctrl: pin gpio5 already requested by madera-pinctrl; cannot claim for gpiochip3
madera-pinctrl madera-pinctrl: pin-4 (gpiochip3) status -22
madera-pinctrl madera-pinctrl: could not request pin 4 (gpio5) from group aif1 on device madera-pinctrl
gpio_stub_drv gpiochip3: Error applying setting, reverse things back
gpio_stub_drv: probe of gpiochip3 failed with error -22
The firmware node on the device created by the GPIO framework is set
through the of_node pointer hence things generally actually work,
however that fwnode->dev is never set, as the check was skipped at
device_add time. This fix appears to match how the I2C subsystem
handles the same situation.
A request could end up on the fpq->io list after fuse_abort_conn() has
reset fpq->connected and aborted requests on that list:
Thread-1 Thread-2
======== ========
->fuse_simple_request() ->shutdown
->__fuse_request_send()
->queue_request() ->fuse_abort_conn()
->fuse_dev_do_read() ->acquire(fpq->lock)
->wait_for(fpq->lock) ->set err to all req's in fpq->io
->release(fpq->lock)
->acquire(fpq->lock)
->add req to fpq->io
After the userspace copy is done the request will be ended, but
req->out.h.error will remain uninitialized. Also the copy might block
despite being already aborted.
Fix both issues by not allowing the request to be queued on the fpq->io
list after fuse_abort_conn() has processed this list.
Reported-by: Pradeep P V K <pragalla@codeaurora.org> Fixes: fd22d62ed0c3 ("fuse: no fc->lock for iqueue parts") Cc: <stable@vger.kernel.org> # v4.2 Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EVM_ALLOW_METADATA_WRITES is an EVM initialization flag that can be set to
temporarily disable metadata verification until all xattrs/attrs necessary
to verify an EVM portable signature are copied to the file. This flag is
cleared when EVM is initialized with an HMAC key, to avoid that the HMAC is
calculated on unverified xattrs/attrs.
Currently EVM unnecessarily denies setting this flag if EVM is initialized
with a public key, which is not a concern as it cannot be used to trust
xattrs/attrs updates. This patch removes this limitation.
evm_inode_init_security() requires an HMAC key to calculate the HMAC on
initial xattrs provided by LSMs. However, it checks generically whether a
key has been loaded, including also public keys, which is not correct as
public keys are not suitable to calculate the HMAC.
Originally, support for signature verification was introduced to verify a
possibly immutable initial ram disk, when no new files are created, and to
switch to HMAC for the root filesystem. By that time, an HMAC key should
have been loaded and usable to calculate HMACs for new files.
More recently support for requiring an HMAC key was removed from the
kernel, so that signature verification can be used alone. Since this is a
legitimate use case, evm_inode_init_security() should not return an error
when no HMAC key has been loaded.
This patch fixes this problem by replacing the evm_key_loaded() check with
a check of the EVM_INIT_HMAC flag in evm_initialized.
In raise_backtrace_ipi() we iterate through the cpumask of CPUs, sending
each an IPI asking them to do a backtrace, but we don't wait for the
backtrace to happen.
We then iterate through the CPU mask again, and if any CPU hasn't done
the backtrace and cleared itself from the mask, we print a trace on its
behalf, noting that the trace may be "stale".
This works well enough when a CPU is not responding, because in that
case it doesn't receive the IPI and the sending CPU is left to print the
trace. But when all CPUs are responding we are left with a race between
the sending and receiving CPUs, if the sending CPU wins the race then it
will erroneously print a trace.
This leads to spurious "stale" traces from the sending CPU, which can
then be interleaved messily with the receiving CPU, note the CPU
numbers, eg:
[ 1658.929157][ C7] rcu: Stack dump where RCU GP kthread last ran:
[ 1658.929223][ C7] Sending NMI from CPU 7 to CPUs 1:
[ 1658.929303][ C1] NMI backtrace for cpu 1
[ 1658.929303][ C7] CPU 1 didn't respond to backtrace IPI, inspecting paca.
[ 1658.929362][ C1] CPU: 1 PID: 325 Comm: kworker/1:1H Tainted: G W E 5.13.0-rc2+ #46
[ 1658.929405][ C7] irq_soft_mask: 0x01 in_mce: 0 in_nmi: 0 current: 325 (kworker/1:1H)
[ 1658.929465][ C1] Workqueue: events_highpri test_work_fn [test_lockup]
[ 1658.929549][ C7] Back trace of paca->saved_r1 (0xc0000000057fb400) (possibly stale):
[ 1658.929592][ C1] NIP: c00000000002cf50 LR: c008000000820178 CTR: c00000000002cfa0
To fix it, change the logic so that the sending CPU waits 5s for the
receiving CPU to print its trace. If the receiving CPU prints its trace
successfully then the sending CPU just continues, avoiding any spurious
"stale" trace.
This has the added benefit of allowing all CPUs to print their traces in
order and avoids any interleaving of their output.
Since the raw memory 'data' does not go forward, it will dump repeated
data if the data length is more than 8. If we want to dump longer data
blocks, we need to repeatedly call macro SEQ_PUT_HEX_FIELD. I think it
is a bit redundant, and multiple function calls also affect the performance.
All internal use cases for tracepoint_probe_register() is set to not ever
be called with the same function and data. If it is, it is considered a
bug, as that means the accounting of handling tracepoints is corrupted.
If the function and data for a tracepoint is already registered when
tracepoint_probe_register() is called, it will call WARN_ON_ONCE() and
return with EEXISTS.
The BPF system call can end up calling tracepoint_probe_register() with
the same data, which now means that this can trigger the warning because
of a user space process. As WARN_ON_ONCE() should not be called because
user space called a system call with bad data, there needs to be a way to
register a tracepoint without triggering a warning.
Enter tracepoint_probe_register_may_exist(), which can be called, but will
not cause a WARN_ON() if the probe already exists. It will still error out
with EEXIST, which will then be sent to the user space that performed the
BPF system call.
This keeps the previous testing for issues with other users of the
tracepoint code, while letting BPF call it with duplicated data and not
warn about it.
With the addition of simple mathematical operations (plus and minus), the
parsing of the "sym-offset" modifier broke, as it took the '-' part of the
"sym-offset" as a minus, and tried to break it up into a mathematical
operation of "field.sym - offset", in which case it failed to parse
(unless the event had a field called "offset").
Both .sym and .sym-offset modifiers should not be entered into
mathematical calculations anyway. If ".sym-offset" is found in the
modifier, then simply make it not an operation that can be calculated on.
Link: https://lkml.kernel.org/r/20210707110821.188ae255@oasis.local.home Cc: Ingo Molnar <mingo@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Daniel Bristot de Oliveira <bristot@redhat.com> Cc: stable@vger.kernel.org Fixes: 100719dcef447 ("tracing: Add simple expression support to hist triggers") Reviewed-by: Tom Zanussi <zanussi@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In AP mode WPA2-PSK connections were not established.
The reason was that the AP was sending the first message
of the 4 way handshake encrypted, even though no pairwise
key had (correctly) yet been set.
Encryption was enabled if the "security_enable" driver flag
was set and encryption was not explicitly disabled by
IEEE80211_TX_INTFL_DONT_ENCRYPT.
However security_enable was set when *any* key, including
the AP GTK key, had been set which was causing unwanted
encryption even if no key was avaialble for the unicast
packet to be sent.
Fix this by adding a check that we have a key and drop
the old security_enable driver flag which is insufficient
and redundant.
The Redpine downstream out of tree driver does it this way too.
Regarding the Fixes tag the actual code being modified was
introduced earlier, with the original driver submission, in dad0d04fa7ba ("rsi: Add RS9113 wireless driver"), however
at that time AP mode was not yet supported so there was
no bug at that point.
So I have tagged the introduction of AP support instead
which was part of the patch set "rsi: support for AP mode" [1]
It is not clear whether AP WPA has ever worked, I can see nothing
on the kernel side that broke it afterwards yet the AP support
patch series says "Tests are performed to confirm aggregation,
connections in WEP and WPA/WPA2 security."
One possibility is that the initial tests were done with a modified
userspace (hostapd).
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> Fixes: 38ef62353acb ("rsi: security enhancements for AP mode") CC: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1622564459-24430-1-git-send-email-martin.fuzzey@flowbird.group Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RSI_RATE_x bits must be assigned to struct rsi_data_desc rate_info
field. The rest of the driver does it correctly, except this one place,
so fix it. This is also aligned with the RSI downstream vendor driver.
Without this patch, an AP operating at 5 GHz does not transmit any
beacons at all, this patch fixes that.
Fixes: d26a9559403c ("rsi: add beacon changes for AP mode") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com> Cc: Angus Ainslie <angus@akkea.ca> Cc: David S. Miller <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Karun Eagalapati <karun256@gmail.com> Cc: Martin Kepplinger <martink@posteo.de> Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm> Cc: Siva Rebbagondla <siva8118@gmail.com> Cc: netdev@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210507213105.140138-1-marex@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It doesn't make sense to clobber the const driver-side buffer, if a
write-to-device attempt failed. All other SSB variants (PCI, PCMCIA and SoC)
also don't corrupt the buffer on any failure in block_write.
Therefore, remove this memset from the SDIO variant.
Signed-off-by: Michael Büsch <m@bues.ch> Cc: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210515210252.318be2ba@wiggum Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I got this crash more times during debugging of PCIe controller and crash
happens somehow at the time when PCIe kernel code started link retraining (as
part of ASPM code) when at the same time PCIe link went down and ath9k probably
executed hw reset procedure.
Currently I'm not able to reproduce this issue as it looks like to be
some race condition between link training, ASPM, link down and reset
path. And as always, race conditions which depends on more input
parameters are hard to reproduce as it depends on precise timings.
But it is clear that pointers are zero in this case and should be
properly filled as same code pattern is used in ath9k_stop() function.
Anyway I was able to reproduce this crash by manually triggering ath
reset worker prior putting card up. I created simple patch to export
reset functionality via debugfs and use it to "simulate" of triggering
reset. s proved that NULL-pointer dereference issue is there.
Function ath9k_hw_reset() is dereferencing chan structure pointer, so it
needs to be non-NULL pointer.
Function ath9k_stop() already contains code which sets ah->curchan to valid
non-NULL pointer prior calling ath9k_hw_reset() function.
Add same code pattern also into ath_reset_internal() function to prevent
kernel NULL pointer dereference in ath9k_hw_reset() function.
This change fixes kernel NULL pointer dereference in ath9k_hw_reset() which
is caused by calling ath9k_hw_reset() from ath_reset_internal() with NULL
chan structure.
The GLOBETROTTER.cis entry in serial_cs matches more devices than
intended and breaks them. Remove it.
Example: # pccardctl info
PRODID_1="Option International
"
PRODID_2="GSM-Ready 56K/ISDN
"
PRODID_3="021
"
PRODID_4="A
"
MANFID=0013,0000
FUNCID=0
result:
pcmcia 0.0: Direct firmware load for cis/GLOBETROTTER.cis failed with error -2
The GLOBETROTTER.cis is nowhere to be found. There's GLOBETROTTER.cis.ihex at
https://netdev.vger.kernel.narkive.com/h4inqdxM/patch-axnet-cs-fix-phy-id-detection-for-bogus-asix-chip#post41
It's from completely diffetent card:
vers_1 4.1, "Option International", "GSM/GPRS GlobeTrotter", "001", "A"
Stop dmaengine transfer in sci_stop_tx(). Otherwise, the following
message is possible output when system enters suspend and while
transferring data, because clearing TIE bit in SCSCR is not able to
stop any dmaengine transfer.
sh-sci e6550000.serial: ttySC1: Unable to drain transmitter
Note that this driver has already used some #ifdef in the .c file
so that this patch also uses #ifdef to fix the issue. Otherwise,
build errors happens if the CONFIG_SERIAL_SH_SCI_DMA is disabled.
The ltr559 chip uses only the lowest bit of the ALS_CONTR register to
configure between active and stand-by mode. In the original driver
BIT(1) is used, which does a software reset instead.
This patch fixes the problem by using BIT(0) as als_mode_active for
the ltr559 chip.
Fixes: 8592a7eefa54 ("iio: ltr501: Add support for ltr559 chip") Signed-off-by: Oliver Lang <Oliver.Lang@gossenmetrawatt.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Nikita Travkin <nikita@trvn.ru> # ltr559 Link: https://lore.kernel.org/r/20210610134619.2101372-3-mkl@pengutronix.de Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regmap is configured for 8 bit registers, uses a RB-Tree cache and
marks several registers as volatile (i.e. do not cache).
The ALS and PS data registers in the chip are 16 bit wide and spans
two regmap registers. In the current driver only the base register is
marked as volatile, resulting in the upper register only read once.
Further the data sheet notes:
| When the I2C read operation starts, all four ALS data registers are
| locked until the I2C read operation of register 0x8B is completed.
Which results in the registers never update after the 2nd read.
This patch fixes the problem by marking the upper 8 bits of the ALS
and PS registers as volatile, too.
Fixes: 2f2c96338afc ("iio: ltr501: Add regmap support.") Reported-by: Oliver Lang <Oliver.Lang@gossenmetrawatt.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Nikita Travkin <nikita@trvn.ru> # ltr559 Link: https://lore.kernel.org/r/20210610134619.2101372-2-mkl@pengutronix.de Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocating an IRQ is conditional to the IRQ existence, but freeing it
was not. If no IRQ was allocate, the driver would still try to free
IRQ 0. Add the missing checks.
This fixes the following trace when the driver is removed:
The STM32MP1 RTC may have 2 clocks, the pclk and the rtc_ck.
If clk_prepare_enable() fails for the second clock (rtc_ck) we must only
call clk_disable_unprepare() for the first clock (pclk) but currently we
call it on both leading to a WARN:
[ 15.629568] WARNING: CPU: 0 PID: 146 at drivers/clk/clk.c:958 clk_core_disable+0xb0/0xc8
[ 15.637620] ck_rtc already disabled
[ 15.663322] CPU: 0 PID: 146 Comm: systemd-udevd Not tainted 5.4.77-pknbsp-svn5759-atag-v5.4.77-204-gea4235203137-dirty #2413
[ 15.674510] Hardware name: STM32 (Device Tree Support)
[ 15.679658] [<c0111148>] (unwind_backtrace) from [<c010c0b8>] (show_stack+0x10/0x14)
[ 15.687371] [<c010c0b8>] (show_stack) from [<c0ab3d28>] (dump_stack+0xc0/0xe0)
[ 15.694574] [<c0ab3d28>] (dump_stack) from [<c012360c>] (__warn+0xc8/0xf0)
[ 15.701428] [<c012360c>] (__warn) from [<c0123694>] (warn_slowpath_fmt+0x60/0x94)
[ 15.708894] [<c0123694>] (warn_slowpath_fmt) from [<c053b518>] (clk_core_disable+0xb0/0xc8)
[ 15.717230] [<c053b518>] (clk_core_disable) from [<c053c190>] (clk_core_disable_lock+0x18/0x24)
[ 15.725924] [<c053c190>] (clk_core_disable_lock) from [<bf0adc44>] (stm32_rtc_probe+0x124/0x5e4 [rtc_stm32])
[ 15.735739] [<bf0adc44>] (stm32_rtc_probe [rtc_stm32]) from [<c05f7d4c>] (platform_drv_probe+0x48/0x98)
[ 15.745095] [<c05f7d4c>] (platform_drv_probe) from [<c05f5cec>] (really_probe+0x1f0/0x458)
[ 15.753338] [<c05f5cec>] (really_probe) from [<c05f61c4>] (driver_probe_device+0x70/0x1c4)
[ 15.761584] [<c05f61c4>] (driver_probe_device) from [<c05f6580>] (device_driver_attach+0x58/0x60)
[ 15.770439] [<c05f6580>] (device_driver_attach) from [<c05f6654>] (__driver_attach+0xcc/0x170)
[ 15.779032] [<c05f6654>] (__driver_attach) from [<c05f40d8>] (bus_for_each_dev+0x58/0x7c)
[ 15.787191] [<c05f40d8>] (bus_for_each_dev) from [<c05f4ffc>] (bus_add_driver+0xdc/0x1f8)
[ 15.795352] [<c05f4ffc>] (bus_add_driver) from [<c05f6ed8>] (driver_register+0x7c/0x110)
[ 15.803425] [<c05f6ed8>] (driver_register) from [<c01027bc>] (do_one_initcall+0x70/0x1b8)
[ 15.811588] [<c01027bc>] (do_one_initcall) from [<c01a1094>] (do_init_module+0x58/0x1f8)
[ 15.819660] [<c01a1094>] (do_init_module) from [<c01a0074>] (load_module+0x1e58/0x23c8)
[ 15.827646] [<c01a0074>] (load_module) from [<c01a0860>] (sys_finit_module+0xa0/0xd4)
[ 15.835459] [<c01a0860>] (sys_finit_module) from [<c01011e0>] (__sys_trace_return+0x0/0x20)
Currently css_wait_for_slow_path() gets called inside the chp->lock.
The path-verification-loop of slowpath inside this lock could lead to
deadlock as reported by the lockdep validator.
The ccw_device_get_chp_desc() during the instance of a device-set-online
would try to acquire the same 'chp->lock' to read the chp->desc.
The instance of this function can get called from multiple scenario,
like probing or setting-device online manually. This could, in some
corner-cases lead to the deadlock.
The chp->lock was introduced to serialize the access of struct
channel_path. This lock is not needed for the css_wait_for_slow_path()
function, so invoke the slow-path function outside this lock.
When find a task from wait queue to wake up, a non-privileged task may
be found out, rather than the privileged. This maybe lead a deadlock
same as commit dfe1fe75e00e ("NFSv4: Fix deadlock between nfs4_evict_inode()
and nfs4_opendata_get_inode()"):
Privileged delegreturn task is queued to privileged list because all
the slots are assigned. If there has no enough slot to wake up the
non-privileged batch tasks(session less than 8 slot), then the privileged
delegreturn task maybe lost waked up because the found out task can't
get slot since the session is on draining.
So we should treate the privileged task as the emergency task, and
execute it as for as we can.
The 'queue->nr' will wraparound from 0 to 255 when only current
priority queue has tasks. This maybe lead a deadlock same as commit dfe1fe75e00e ("NFSv4: Fix deadlock between nfs4_evict_inode()
and nfs4_opendata_get_inode()"):
Privileged delegreturn task is queued to privileged list because all
the slots are assigned. When non-privileged task complete and release
the slot, a non-privileged maybe picked out. It maybe allocate slot
failed when the session on draining.
If the 'queue->nr' has wraparound to 255, and no enough slot to
service it, then the privileged delegreturn will lost to wake up.
Rather than just indicating that transmission can start, this patch
requires the explicit flushing of the network TX queue when the driver
is informed by the device that it can transmit, next to its
configuration.
In this way, if frames have already been written by the application,
they will actually be transmitted.
can_can_gw_rcv() is called under RCU protection, so after calling
can_rx_unregister(), we have to call synchronize_rcu in order to wait
for any RCU read-side critical sections to finish before removing the
kmem_cache entry with the referenced gw job entry.
Link: https://lore.kernel.org/r/20210618173645.2238-1-socketcan@hartkopp.net Fixes: c1aabdf379bc ("can-gw: add netlink based CAN routing") Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
can_rx_register() callbacks may be called concurrently to the call to
can_rx_unregister(). The callbacks and callback data, though, are
protected by RCU and the struct sock reference count.
So the callback data is really attached to the life of sk, meaning
that it should be released on sk_destruct. However, bcm_remove_op()
calls tasklet_kill(), and RCU callbacks may be called under RCU
softirq, so that cannot be used on kernels before the introduction of
HRTIMER_MODE_SOFT.
However, bcm_rx_handler() is called under RCU protection, so after
calling can_rx_unregister(), we may call synchronize_rcu() in order to
wait for any RCU read-side critical sections to finish. That is,
bcm_rx_handler() won't be called anymore for those ops. So, we only
free them, after we do that synchronize_rcu().
Fixes: ffd980f976e7 ("[CAN]: Add broadcast manager (bcm) protocol") Link: https://lore.kernel.org/r/20210619161813.2098382-1-cascardo@canonical.com Cc: linux-stable <stable@vger.kernel.org> Reported-by: syzbot+0f7e7e5e2f4f40fa89c0@syzkaller.appspotmail.com Reported-by: Norbert Slusarek <nslusarek@gmx.net> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5d1b1b3f492f ("ext4: fix BUG when calling ext4_error with locked
block group") introduces ext4_grp_locked_error to handle unlocking a
group in error cases. Otherwise, there is a possibility of a sleep while
atomic. However, since 43c73221b3b1 ("ext4: replace BUG_ON with WARN_ON
in mb_find_extent()"), mb_find_extent() has contained a ext4_error()
call while a group spinlock is held. Replace this with
ext4_grp_locked_error.
Fixes: 43c73221b3b1 ("ext4: replace BUG_ON with WARN_ON in mb_find_extent()") Cc: <stable@vger.kernel.org> # 4.14+ Signed-off-by: Stephen Brennan <stephen.s.brennan@oracle.com> Reviewed-by: Lukas Czerner <lczerner@redhat.com> Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com> Link: https://lore.kernel.org/r/20210623232114.34457-1-stephen.s.brennan@oracle.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After converting fs shrinkers to new scan/count API, we are no longer
pass zero nr_to_scan parameter to detect the number of objects to free,
just remove this check.
Fixes: 1ab6c4997e04 ("fs: convert fs shrinkers to new scan/count API") Cc: stable@vger.kernel.org # 3.12+ Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20210522103045.690103-2-yi.zhang@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cache_cnt parameter of tracepoint ext4_es_shrink_exit means the
remaining cache count after shrink, but now it is the cache count before
shrink, fix it by read sbi->s_extent_cache_cnt again.
Fixes: 1ab6c4997e04 ("fs: convert fs shrinkers to new scan/count API") Cc: stable@vger.kernel.org # 3.12+ Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20210522103045.690103-3-yi.zhang@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit c89128a00838 ("ext4: handle errors on
ext4_commit_super"), 'ret' may be set to 0 before calling
ext4_fill_flex_info(), if ext4_fill_flex_info() fails ext4_mount()
doesn't return error code, it makes 'root' is null which causes crash
in legacy_get_tree().
Fixes: c89128a00838 ("ext4: handle errors on ext4_commit_super") Reported-by: Hulk Robot <hulkci@huawei.com> Cc: <stable@vger.kernel.org> # v4.18+ Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20210510111051.55650-1-yangyingliang@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize eh_generation of struct ext4_extent_header to prevent leaking
info to userspace. Fixes KMSAN kernel-infoleak bug reported by syzbot at:
http://syzkaller.appspot.com/bug?id=78e9ad0e6952a3ca16e8234724b2fa92d041b9b8
In ext4_orphan_cleanup(), if ext4_truncate() failed to get a transaction
handle, it didn't remove the inode from the in-core orphan list, which
may probably trigger below error dump in ext4_destroy_inode() during the
final iput() and could lead to memory corruption on the later orphan
list changes.
The defrag loop processes leaves in batches and starting transaction for
each. The whole defragmentation on a given root is protected by a bit
but in case the transaction fails, the bit is not cleared
In case the transaction fails the bit would prevent starting
defragmentation again, so make sure it's cleared.
During an incremental send operation, when processing the new references
for the current inode, we might send an unlink operation for another inode
that has a conflicting path and has more than one hard link. However this
path was computed and cached before we processed previous new references
for the current inode. We may have orphanized a directory of that path
while processing a previous new reference, in which case the path will
be invalid and cause the receiver process to fail.
The following reproducer triggers the problem and explains how/why it
happens in its comments:
$ cat test-send-unlink.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
mkfs.btrfs -f $DEV >/dev/null
mount $DEV $MNT
# Create our test files and directory. Inode 259 (file3) has two hard
# links.
touch $MNT/file1
touch $MNT/file2
touch $MNT/file3
# Now create the base snapshot, which is going to be the parent snapshot
# for a later incremental send.
btrfs subvolume snapshot -r $MNT $MNT/snap1
btrfs send -f /tmp/snap1.send $MNT/snap1
# Move inode 257 into directory inode 260. This results in computing the
# path for inode 260 as "/A" and caching it.
mv $MNT/file1 $MNT/A/file1
# Move inode 258 (file2) into directory inode 260, with a name of
# "hard_link", moving first inode 259 away since it currently has that
# location and name.
mv $MNT/A/hard_link $MNT/tmp
mv $MNT/file2 $MNT/A/hard_link
# Now rename inode 260 to something else (B for example) and then create
# a hard link for inode 258 that has the old name and location of inode
# 260 ("/A").
mv $MNT/A $MNT/B
ln $MNT/B/hard_link $MNT/A
# Create another snapshot of our subvolume and use it for an incremental
# send.
btrfs subvolume snapshot -r $MNT $MNT/snap2
btrfs send -f /tmp/snap2.send -p $MNT/snap1 $MNT/snap2
# Now unmount the filesystem, create a new one, mount it and try to
# apply both send streams to recreate both snapshots.
umount $DEV
mkfs.btrfs -f $DEV >/dev/null
mount $DEV $MNT
# First add the first snapshot to the new filesystem by applying the
# first send stream.
btrfs receive -f /tmp/snap1.send $MNT
# The incremental receive operation below used to fail with the
# following error:
#
# ERROR: unlink A/hard_link failed: No such file or directory
#
# This is because when send is processing inode 257, it generates the
# path for inode 260 as "/A", since that inode is its parent in the send
# snapshot, and caches that path.
#
# Later when processing inode 258, it first processes its new reference
# that has the path of "/A", which results in orphanizing inode 260
# because there is a a path collision. This results in issuing a rename
# operation from "/A" to "/o260-6-0".
#
# Finally when processing the new reference "B/hard_link" for inode 258,
# it notices that it collides with inode 259 (not yet processed, because
# it has a higher inode number), since that inode has the name
# "hard_link" under the directory inode 260. It also checks that inode
# 259 has two hardlinks, so it decides to issue a unlink operation for
# the name "hard_link" for inode 259. However the path passed to the
# unlink operation is "/A/hard_link", which is incorrect since currently
# "/A" does not exists, due to the orphanization of inode 260 mentioned
# before. The path is incorrect because it was computed and cached
# before the orphanization. This results in the receiver to fail with
# the above error.
btrfs receive -f /tmp/snap2.send $MNT
umount $MNT
When running the test, it fails like this:
$ ./test-send-unlink.sh
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap1'
At subvol /mnt/sdi/snap1
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap2'
At subvol /mnt/sdi/snap2
At subvol snap1
At snapshot snap2
ERROR: unlink A/hard_link failed: No such file or directory
Fix this by recomputing a path before issuing an unlink operation when
processing the new references for the current inode if we previously
have orphanized a directory.
A test case for fstests will follow soon.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3a95200d3f89 ("arm_pmu: Change API to support 64bit counter values")
changes the input "value" type from 32-bit to 64-bit, which introduces the
following problem: ARMv7 PMU counters is 32-bit width, in big-endian mode,
write counter uses high 32-bit, which writes an incorrect value.
Fixes: 3a95200d3f89 ("arm_pmu: Change API to support 64bit counter values") Cc: <stable@vger.kernel.org> Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Link: https://lore.kernel.org/r/20210430012659.232110-1-yangjihong1@huawei.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though we validate user-provided inputs we then traverse past
validated data when applying the new map. The issue was originally
discovered by Murray McAllister with this simple POC (if the following
is executed by an unprivileged user it will instantly panic the system):
int main(void) {
int fd, ret;
unsigned int buffer[10000];
When checking the file name attribute, we want to ensure that it fits
within the bounds of ATTR_RECORD. To do this, we should check that (attr
record + file name offset + file name length) < (attr record + attr record
length).
However, the original check did not include the file name offset in the
calculation. This means that corrupted on-disk metadata might not caught
by the incorrect file name check, and lead to an invalid memory access.
An example can be seen in the crash report of a memory corruption error
found by Syzbot:
https://syzkaller.appspot.com/bug?id=a1a1e379b225812688566745c3e2f7242bffc246
Adding the file name offset to the validity check fixes this error and
passes the Syzbot reproducer test.
when system is doing s4, the process of xhci_resume may be as below:
1、xhci_mem_cleanup
2、xhci_init->xhci_mem_init->xhci_mem_cleanup(when memory is not enough).
xhci_mem_cleanup will be executed twice when system is out of memory.
xhci->port_caps is freed in xhci_mem_cleanup,but it isn't set to NULL.
It will be freed twice when xhci_mem_cleanup is called the second time.
We got following bug when system resumes from s4:
kernel BUG at mm/slub.c:309!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
CPU: 0 PID: 5929 Tainted: G S W 5.4.96-arm64-desktop #1
pc : __slab_free+0x5c/0x424
lr : kfree+0x30c/0x32c
Creation EP's debugfs called earlier than debugfs folder for dwc3
device created. As result EP's debugfs are created in '/sys/kernel/debug'
instead of '/sys/kernel/debug/usb/dwc3.1.auto'.
Moved dwc3_debugfs_init() function call before calling
dwc3_core_init_mode() to allow create dwc3 debugfs parent before
creating EP's debugfs's.
The device (32a7:0000 Heimann Sensor GmbH USB appset demo) claims to be
a CDC-ACM device in its descriptors but in fact is not. If it is run
with echo disabled it returns garbled data, probably due to something
that happens in the TTY layer. And when run with echo enabled (the
default), it will mess up the calibration data of the sensor the first
time any data is sent to the device.
In short, I had a bad time after connecting the sensor and trying to get
it to work. I hope blacklisting it in the cdc-acm driver will save
someone else a bit of trouble.
when receive eem echo command, it will send a response,
but queue this response to the usb request which allocate
from gadget device endpoint zero,
and transmit the request to IN endpoint of eem interface.
on dwc3 gadget, it will trigger following warning in function
__dwc3_gadget_ep_queue(),
if (WARN(req->dep != dep, "request %pK belongs to '%s'\n",
&req->request, req->dep->name))
return -EINVAL;
fix it by allocating a usb request from IN endpoint of eem interface,
and transmit the usb request to same IN endpoint of eem interface.
In ems_usb_disconnect() dev pointer, which is netdev private data, is
used after free_candev() call:
| if (dev) {
| unregister_netdev(dev->netdev);
| free_candev(dev->netdev);
|
| unlink_all_urbs(dev);
|
| usb_free_urb(dev->intr_urb);
|
| kfree(dev->intr_in_buffer);
| kfree(dev->tx_msg_buffer);
| }
Fix it by simply moving free_candev() at the end of the block.
Fail log:
| BUG: KASAN: use-after-free in ems_usb_disconnect
| Read of size 8 at addr ffff88804e041008 by task kworker/1:2/2895
|
| CPU: 1 PID: 2895 Comm: kworker/1:2 Not tainted 5.13.0-rc5+ #164
| Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a-rebuilt.opensuse.4
| Workqueue: usb_hub_wq hub_event
| Call Trace:
| dump_stack (lib/dump_stack.c:122)
| print_address_description.constprop.0.cold (mm/kasan/report.c:234)
| kasan_report.cold (mm/kasan/report.c:420 mm/kasan/report.c:436)
| ems_usb_disconnect (drivers/net/can/usb/ems_usb.c:683 drivers/net/can/usb/ems_usb.c:1058)
Fixes: 702171adeed3 ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface") Link: https://lore.kernel.org/r/20210617185130.5834-1-paskripkin@gmail.com Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the four control requests which erroneously used usb_rcvctrlpipe().
Fixes: 1d3e20236d7a ("[PATCH] USB: usbtouchscreen: unified USB touchscreen driver") Fixes: 24ced062a296 ("usbtouchscreen: add support for DMC TSC-10/25 devices") Fixes: 9e3b25837a20 ("Input: usbtouchscreen - add support for e2i touchscreen controller") Signed-off-by: Johan Hovold <johan@kernel.org> Cc: stable@vger.kernel.org # 2.6.17 Link: https://lore.kernel.org/r/20210524092048.4443-1-johan@kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
