All devices supported by ina2xx are bidirectional and report the
measured shunt voltage and power values as a signed 16 bit, but the
current driver implementation caches all registers as u16, leading
to an incorrect sign extension when reporting to userspace in
ina2xx_get_value().
This patch fixes the problem by casting the signed registers to s16.
Tested on an INA219.
allows the fall through to the non-layered write case even if both
parent_overlap and obj_request->img_offset belong to the same RADOS
object. This leads to data corruption, because the area to the left of
parent_overlap ends up unconditionally zero-filled instead of being
populated with parent data. Suppose we want to write 1M to offset 6M
of image bar, which is a clone of foo@snap; object_size is 4M,
parent_overlap is 5M:
rbd_data.<id>.0000000000000001
---------------------|----------------------|------------
| should be copyup'ed | should be zeroed out | write ...
---------------------|----------------------|------------
4M 5M 6M
parent_overlap obj_request->img_offset
4..5M should be copyup'ed from foo, yet it is zero-filled, just like
5..6M is.
Given that the only striping mode kernel client currently supports is
chunking (i.e. stripe_unit == object_size, stripe_count == 1), round
parent_overlap up to the next object boundary for the purposes of the
overlap check.
Each image request contains a reference count, but to date it has
not actually been used. (I think this was just an oversight.) A
recent report involving rbd failing an assertion shed light on why
and where we need to use these reference counts.
Every OSD request associated with an object request uses
rbd_osd_req_callback() as its callback function. That function will
call a helper function (dependent on the type of OSD request) that
will set the object request's "done" flag if the object request if
appropriate. If that "done" flag is set, the object request is
passed to rbd_obj_request_complete().
In rbd_obj_request_complete(), requests are processed in sequential
order. So if an object request completes before one of its
predecessors in the image request, the completion is deferred.
Otherwise, if it's a completing object's "turn" to be completed, it
is passed to rbd_img_obj_end_request(), which records the result of
the operation, accumulates transferred bytes, and so on. Next, the
successor to this request is checked and if it is marked "done",
(deferred) completion processing is performed on that request, and
so on. If the last object request in an image request is completed,
rbd_img_request_complete() is called, which (typically) destroys
the image request.
There is a race here, however. The instant an object request is
marked "done" it can be provided (by a thread handling completion of
one of its predecessor operations) to rbd_img_obj_end_request(),
which (for the last request) can then lead to the image request
getting torn down. And this can happen *before* that object has
itself entered rbd_img_obj_end_request(). As a result, once it
*does* enter that function, the image request (and even the object
request itself) may have been freed and become invalid.
All that's necessary to avoid this is to properly count references
to the image requests. We tear down an image request's object
requests all at once--only when the entire image request has
completed. So there's no need for an image request to count
references for its object requests. However, we don't want an
image request to go away until the last of its object requests
has passed through rbd_img_obj_callback(). In other words,
we don't want rbd_img_request_complete() to necessarily
result in the image request being destroyed, because it may
get called before we've finished processing on all of its
object requests.
So the fix is to add a reference to an image request for
each of its object requests. The reference can be viewed
as representing an object request that has not yet finished
its call to rbd_img_obj_callback(). That is emphasized by
getting the reference right after assigning that as the image
object's callback function. The corresponding release of that
reference is done at the end of rbd_img_obj_callback(), which
every image object request passes through exactly once.
DM thinp already checks whether the discard_granularity of the data
device is a factor of the thin-pool block size. But when using the
dm-thin-pool's discard passdown support, DM thinp was not selecting the
max of the underlying data device's discard_granularity and the
thin-pool's block size.
Update set_discard_limits() to set discard_granularity to the max of
these values. This enables blkdev_issue_discard() to properly align the
discards that are sent to the DM thin device on a full block boundary.
As such each discard will now cover an entire DM thin-pool block and the
block will be reclaimed.
The SMP code expects hdev to be unlocked since e.g. crypto functions
will try to (re)lock it. Therefore, we need to release the lock before
calling into smp.c from mgmt.c. Without this we risk a deadlock whenever
the smp_user_confirm_reply() function is called.
The conn->link_key variable tracks the type of link key in use. It is
set whenever we respond to a link key request as well as when we get a
link key notification event.
These two events do not however always guarantee that encryption is
enabled: getting a link key request and responding to it may only mean
that the remote side has requested authentication but not encryption. On
the other hand, the encrypt change event is a certain guarantee that
encryption is enabled. The real encryption state is already tracked in
the conn->link_mode variable through the HCI_LM_ENCRYPT bit.
This patch fixes a check for encryption in the hci_conn_auth function to
use the proper conn->link_mode value and thereby eliminates the chance
of a false positive result.
From the Bluetooth Core Specification 4.1 page 1958:
"if both devices have set the Authentication_Requirements parameter to
one of the MITM Protection Not Required options, authentication stage 1
shall function as if both devices set their IO capabilities to
DisplayOnly (e.g., Numeric comparison with automatic confirmation on
both devices)"
So far our implementation has done user confirmation for all just-works
cases regardless of the MITM requirements, however following the
specification to the word means that we should not be doing confirmation
when neither side has the MITM flag set.
Commit "drm/vmwgfx: correct fb_fix_screeninfo.line_length", while fixing a
vmwgfx fbdev bug, also writes the pitch to a supposedly read-only register:
SVGA_REG_BYTES_PER_LINE, while it should be (and also in fact is) written to
SVGA_REG_PITCHLOCK.
This patch is Cc'd stable because of the unknown effects writing to this
register might have, particularly on older device versions.
v2: Updated log message.
Cc: Christopher Friedt <chrisfriedt@gmail.com> Tested-by: Christopher Friedt <chrisfriedt@gmail.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marek Olšák <marek.olsak@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In omap_elm_correct_data(), if bitflip_count in an erased-page is within the
correctable limit (< ecc.strength), then it is not indicated back to the caller
ecc->read_page().
This mis-guides upper layers like MTD and UBIFS layer to assume erased-page as
perfectly clean and use it for writing even if actual bitflip_count was
dangerously high (bitflip_count > mtd->bitflip_threshold).
This patch fixes this above issue, by returning 'stats' to caller
ecc->read_page() under all scenarios.
Reported-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Pekon Gupta <pekon@ti.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As subpage write is enabled by default for all drivers, nand_write_subpage_hwecc
causes a crash if the driver did not register ecc->hwctl or ecc->calculate.
This behavior was introduced in
commit 837a6ba4f3b6d23026674e6af6b6849a4634fff9
"mtd: nand: subpage write support for hardware based ECC schemes".
This fixes a crash by emulating subpage write support by padding sub-page data
with 0xff on either sides to make it full page compatible.
Reported-by: Helmut Schaa <helmut.schaa@googlemail.com> Tested-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Pekon Gupta <pekon@ti.com> Reviewed-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by Niels, starting rfkill polling during device probe
(commit e2bc7c5, generally sane change) broke rfkill on rt2500pci
device. I considered that bug as some initalization issue, which
should be fixed on rt2500pci specific code. But after several
attempts (see bug report for details) we fail to find working solution.
Hence I decided to revert to old behaviour on rt2500pci to fix
regression.
Additionally patch also unregister rfkill on device remove instead
of ifconfig down, what was another issue introduced by bad commit.
If the descriptors do not need any strings and user space sends empty
set of strings, the ffs->stringtabs field remains NULL. Thus
*ffs->stringtabs in functionfs_bind leads to a NULL pointer
dereferenece.
The bug was introduced by commit [fd7c9a007f: “use usb_string_ids_n()”].
While at it, remove double initialisation of lang local variable in
that function.
ffs->strings_count does not need to be checked in any way since in
the above scenario it will remain zero and usb_string_ids_n() is
a no-operation when colled with 0 argument.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device vendor and product id is 1c9e:9800
It is working as serial interface with generic usbserial driver.
I thought it is more suitable to use usbserial option driver, which has
better capability distinguishing between modem serial interface and
micro sd storage interface.
[ johan: style changes ]
Signed-off-by: Oliver Neukum <oneukum@suse.de> Tested-by: Alif Mubarak Ahmad <alive4ever@live.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The system suspend flow as following:
1, Freeze all user processes and kenrel threads.
2, Try to suspend all devices.
2.1, If pci device is in RPM suspended state, then pci driver will try
to resume it to RPM active state in the prepare stage.
2.2, xhci_resume function calls usb_hcd_resume_root_hub to queue two
workqueue items to resume usb2&usb3 roothub devices.
2.3, Call suspend callbacks of devices.
2.3.1, All suspend callbacks of all hcd's children, including
roothub devices are called.
2.3.2, Finally, hcd_pci_suspend callback is called.
Due to workqueue threads were already frozen in step 1, the workqueue
items can't be scheduled, and the roothub devices can't be resumed in
this flow. The HCD_FLAG_WAKEUP_PENDING flag which is set in
usb_hcd_resume_root_hub won't be cleared. Finally,
hcd_pci_suspend will return -EBUSY, and system suspend fails.
The reason why this issue doesn't show up very often is due to that
choose_wakeup will be called in step 2.3.1. In step 2.3.1, if
udev->do_remote_wakeup is not equal to device_may_wakeup(&udev->dev), then
udev will resume to RPM active for changing the wakeup settings. This
has been a lucky hit which hides this issue.
For some special xHCI controllers which have no USB2 port, then roothub
will not match hub driver due to probe failed. Then its
do_remote_wakeup will be set to zero, and we won't be as lucky.
xhci driver doesn't need to resume roothub devices everytime like in
the above case. It's only needed when there are pending event TRBs.
This patch should be back-ported to kernels as old as 3.2, that
contains the commit f69e3120df82391a0ee8118e0a156239a06b2afb
"USB: XHCI: resume root hubs when the controller resumes"
The transfer burst count (TBC) field in xhci 1.0 hosts should be set
to the number of bursts needed to transfer all packets in a isoc TD.
Supported values are 0-2 (1 to 3 bursts per service interval).
Formula for TBC calculation is given in xhci spec section 4.11.2.3:
TBC = roundup( Transfer Descriptor Packet Count / Max Burst Size +1 ) - 1
This patch should be applied to stable kernels since 3.0 that contain
the commit 5cd43e33b9519143f06f507dd7cbee6b7a621885
"xhci 1.0: Set transfer burst count field."
Even though the virtio-scsi spec guarantees that all requests related
to the TMF will have been completed by the time the TMF itself completes,
the request queue's callback might not have run yet. This causes requests
to be completed more than once, and as a result triggers a variety of
BUGs or oopses.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Venkatesh Srinivas <venkateshs@google.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling the workqueue interface on uninitialized work items isn't a
good idea even if they're zeroed. It's not failing catastrophically only
through happy accidents.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a memory barrier prior to sending a new command to the VIOS
to ensure the VIOS does not receive stale data in the command buffer.
Also add a memory barrier when processing the CRQ for completed commands.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a CRQ reset is triggered for some reason while in the middle
of performing VSCSI adapter initialization, we don't want to
call the done function for the initialization MAD commands as
this will only result in two threads attempting initialization
at the same time, resulting in failures.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syscall_regfunc() and syscall_unregfunc() should set/clear
TIF_SYSCALL_TRACEPOINT system-wide, but do_each_thread() can race
with copy_process() and miss the new child which was not added to
the process/thread lists yet.
Change copy_process() to update the child's TIF_SYSCALL_TRACEPOINT
under tasklist.
Link: http://lkml.kernel.org/p/20140413185854.GB20668@redhat.com Fixes: a871bd33a6c0 "tracing: Add syscall tracepoints" Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to prevent the saved cmdline cache from being filled when
tracing is not active, the comms are only recorded after a trace event
is recorded.
The problem is, a comm can fail to be recorded if the trace_cmdline_lock
is held. That lock is taken via a trylock to allow it to happen from
any context (including NMI). If the lock fails to be taken, the comm
is skipped. No big deal, as we will try again later.
But! Because of the code that was added to only record after an event,
we may not try again later as the recording is made as a oneshot per
event per CPU.
Only disable the recording of the comm if the comm is actually recorded.
Fixes: 7ffbd48d5cab "tracing: Cache comms only after an event occurred" Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the SubmittingPatches process to include howto about the new
'Fixes:' tag to be used when a patch fixes an issue in a previous commit
(found by git-bisect for example).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ulog messages leak heap bytes by the means of padding bytes and
incompletely filled string arrays. Fix those by memset(0)'ing the
whole struct before filling it.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Cc: Jan Tore Morken <jantore@morken.priv.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We cleared H_RST for H_CSR on spurious interrupt generated when ME_RDY
while cleared and not while ME_RDY is set. The spurious interrupt
is not delivered on all platforms in this case the
driver may fail to initialize.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'sysret' fastpath does not correctly restore even all regular
registers, much less any segment registers or reflags values. That is
very much part of why it's faster than 'iret'.
Normally that isn't a problem, because the normal ptrace() interface
catches the process using the signal handler infrastructure, which
always returns with an iret.
However, some paths can get caught using ptrace_event() instead of the
signal path, and for those we need to make sure that we aren't going to
return to user space using 'sysret'. Otherwise the modifications that
may have been done to the register set by the tracer wouldn't
necessarily take effect.
Fix it by forcing IRET path by setting TIF_NOTIFY_RESUME from
arch_ptrace_stop_needed() which is invoked from ptrace_stop().
Prior to commit 0e4f6a791b1e (Fix reiserfs_file_release()), reiserfs
truncates serialized on i_mutex. They mostly still do, with the exception
of reiserfs_file_release. That blocks out other writers via the tailpack
mutex and the inode openers counter adjusted in reiserfs_file_open.
However, NFS will call reiserfs_setattr without having called ->open, so
we end up with a race when nfs is calling ->setattr while another
process is releasing the file. Ultimately, it triggers the
BUG_ON(inode->i_size != new_file_size) check in maybe_indirect_to_direct.
The solution is to pull the lock into reiserfs_setattr to encompass the
truncate_setsize call as well.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Vector Crypto category instructions are supported by current POWER8
chips, advertise them to userspace using a specific bit to properly
differentiate with chips of the same architecture level that might not
have them.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b0d278b7d3ae ("powerpc/perf_event: Reduce latency of calling
perf_event_do_pending") added a check for CONFIG_PMAC were a check for
CONFIG_PPC_PMAC was clearly intended.
Fixes: b0d278b7d3ae ("powerpc/perf_event: Reduce latency of calling perf_event_do_pending") Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f9c0119d7ba (compat: fs: Generic compat_sys_sendfile
implementation) changed the PowerPC 64bit sendfile call from
sys_sendile64 to sys_sendfile.
Unfortunately this broke sendfile of lengths greater than 2G because
sys_sendfile caps at MAX_NON_LFS. Restore what we had previously which
fixes the bug.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In pseries_eeh_get_state(), EEH_STATE_UNAVAILABLE is always
overwritten by EEH_STATE_NOT_SUPPORT because of the missed
"break" there. The patch fixes the issue.
Reported-by: Joe Perches <joe@perches.com> Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the DRC cache pruner will stop scanning the list when it
hits an entry that is RC_INPROG. It's possible however for a call to
take a *very* long time. In that case, we don't want it to block other
entries from being pruned if they are expired or we need to trim the
cache to get back under the limit.
Fix the DRC cache pruner to just ignore RC_INPROG entries.
Signed-off-by: Jeff Layton <jlayton@primarydata.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently when we are processing a request, we try to scrape an expired
or over-limit entry off the list in preference to allocating a new one
from the slab.
This is unnecessarily complicated. Just use the slab layer.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a bug, whereby nfs_update_inode() was declaring the inode to be
up to date despite not having checked all the attributes.
The bug occurs because the temporary variable in which we cache
the validity information is 'sanitised' before reapplying to
nfsi->cache_validity.
Note nobody's ever noticed because the typical client probably never
requests FILES_AVAIL without also requesting something else on the list.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
27b11428b7de ("nfsd4: remove lockowner when removing lock stateid")
introduced a memory leak.
Reported-by: Jeff Layton <jeff.layton@primarydata.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid that closing /dev/infiniband/umad<n> or /dev/infiniband/issm<n>
triggers a use-after-free. __fput() invokes f_op->release() before it
invokes cdev_put(). Make sure that the ib_umad_device structure is
freed by the cdev_put() call instead of f_op->release(). This avoids
that changing the port mode from IB into Ethernet and back to IB
followed by restarting opensmd triggers the following kernel oops:
Avoid leaking a kref count in ib_umad_open() if port->ib_dev == NULL
or if nonseekable_open() fails.
Avoid leaking a kref count, that sm_sem is kept down and also that the
IB_PORT_SM capability mask is not cleared in ib_umad_sm_open() if
nonseekable_open() fails.
Since container_of() never returns NULL, remove the code that tests
whether container_of() returns NULL.
Moving the kref_get() call from the start of ib_umad_*open() to the
end is safe since it is the responsibility of the caller of these
functions to ensure that the cdev pointer remains valid until at least
when these functions return.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
[ydroneaud@opteya.com: rework a bit to reduce the amount of code changed]
Avoid that the loops that iterate over the request ring can encounter
a pointer to a SCSI command in req->scmnd that is no longer associated
with that request. If the function srp_unmap_data() is invoked twice
for a SCSI command that is not in flight then that would cause
ib_fmr_pool_unmap() to be invoked with an invalid pointer as argument,
resulting in a kernel oops.
This patch addresses an issue where the legacy diagpacket is sent in
from the user, but the driver operates on only the extended
diagpkt. This patch specifically initializes the extended diagpkt
based on the legacy packet.
Reported-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code used a literal 1 in dispatching an IB_EVENT_PKEY_CHANGE.
As of the dual port qib QDR card, this is not necessarily correct.
Change to use the port as specified in the call.
Reported-by: Alex Estrin <alex.estrin@intel.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some AR934x based systems, where the frequency of
the AHB bus is relatively high, the built-in watchdog
causes a spurious restart when it gets enabled.
The possible cause of these restarts is that the timeout
value written into the TIMER register does not reaches
the hardware in time.
Add an explicit delay into the ath79_wdt_enable function
to avoid the spurious restarts.
Implementation of ->set_timeout() is supposed to set 'timeout' field of 'struct
watchdog_device' passed to it. sp805 was rather setting this in a local
variable. Fix it.
I hit the same assert failed as Dolev Raviv reported in Kernel v3.10
shows like this:
[ 9641.164028] UBIFS assert failed in shrink_tnc at 131 (pid 13297)
[ 9641.234078] CPU: 1 PID: 13297 Comm: mmap.test Tainted: G O 3.10.40 #1
[ 9641.234116] [<c0011a6c>] (unwind_backtrace+0x0/0x12c) from [<c000d0b0>] (show_stack+0x20/0x24)
[ 9641.234137] [<c000d0b0>] (show_stack+0x20/0x24) from [<c0311134>] (dump_stack+0x20/0x28)
[ 9641.234188] [<c0311134>] (dump_stack+0x20/0x28) from [<bf22425c>] (shrink_tnc_trees+0x25c/0x350 [ubifs])
[ 9641.234265] [<bf22425c>] (shrink_tnc_trees+0x25c/0x350 [ubifs]) from [<bf2245ac>] (ubifs_shrinker+0x25c/0x310 [ubifs])
[ 9641.234307] [<bf2245ac>] (ubifs_shrinker+0x25c/0x310 [ubifs]) from [<c00cdad8>] (shrink_slab+0x1d4/0x2f8)
[ 9641.234327] [<c00cdad8>] (shrink_slab+0x1d4/0x2f8) from [<c00d03d0>] (do_try_to_free_pages+0x300/0x544)
[ 9641.234344] [<c00d03d0>] (do_try_to_free_pages+0x300/0x544) from [<c00d0a44>] (try_to_free_pages+0x2d0/0x398)
[ 9641.234363] [<c00d0a44>] (try_to_free_pages+0x2d0/0x398) from [<c00c6a60>] (__alloc_pages_nodemask+0x494/0x7e8)
[ 9641.234382] [<c00c6a60>] (__alloc_pages_nodemask+0x494/0x7e8) from [<c00f62d8>] (new_slab+0x78/0x238)
[ 9641.234400] [<c00f62d8>] (new_slab+0x78/0x238) from [<c031081c>] (__slab_alloc.constprop.42+0x1a4/0x50c)
[ 9641.234419] [<c031081c>] (__slab_alloc.constprop.42+0x1a4/0x50c) from [<c00f80e8>] (kmem_cache_alloc_trace+0x54/0x188)
[ 9641.234459] [<c00f80e8>] (kmem_cache_alloc_trace+0x54/0x188) from [<bf227908>] (do_readpage+0x168/0x468 [ubifs])
[ 9641.234553] [<bf227908>] (do_readpage+0x168/0x468 [ubifs]) from [<bf2296a0>] (ubifs_readpage+0x424/0x464 [ubifs])
[ 9641.234606] [<bf2296a0>] (ubifs_readpage+0x424/0x464 [ubifs]) from [<c00c17c0>] (filemap_fault+0x304/0x418)
[ 9641.234638] [<c00c17c0>] (filemap_fault+0x304/0x418) from [<c00de694>] (__do_fault+0xd4/0x530)
[ 9641.234665] [<c00de694>] (__do_fault+0xd4/0x530) from [<c00e10c0>] (handle_pte_fault+0x480/0xf54)
[ 9641.234690] [<c00e10c0>] (handle_pte_fault+0x480/0xf54) from [<c00e2bf8>] (handle_mm_fault+0x140/0x184)
[ 9641.234716] [<c00e2bf8>] (handle_mm_fault+0x140/0x184) from [<c0316688>] (do_page_fault+0x150/0x3ac)
[ 9641.234737] [<c0316688>] (do_page_fault+0x150/0x3ac) from [<c000842c>] (do_DataAbort+0x3c/0xa0)
[ 9641.234759] [<c000842c>] (do_DataAbort+0x3c/0xa0) from [<c0314e38>] (__dabt_usr+0x38/0x40)
After analyzing the code, I found a condition that may cause this failed
in correct operations. Thus, I think this assertion is wrong and should be
removed.
Suppose there are two clean znodes and one dirty znode in TNC. So the
per-filesystem atomic_t @clean_zn_cnt is (2). If commit start, dirty_znode
is set to COW_ZNODE in get_znodes_to_commit() in case of potentially ops
on this znode. We clear COW bit and DIRTY bit in write_index() without
@tnc_mutex locked. We don't increase @clean_zn_cnt in this place. As the
comments in write_index() shows, if another process hold @tnc_mutex and
dirty this znode after we clean it, @clean_zn_cnt would be decreased to (1).
We will increase @clean_zn_cnt to (2) with @tnc_mutex locked in
free_obsolete_znodes() to keep it right.
If shrink_tnc() performs between decrease and increase, it will release
other 2 clean znodes it holds and found @clean_zn_cnt is less than zero
(1 - 2 = -1), then hit the assertion. Because free_obsolete_znodes() will
soon correct @clean_zn_cnt and no harm to fs in this case, I think this
assertion could be removed.
2 clean zondes and 1 dirty znode, @clean_zn_cnt == 2
Thread A (commit) Thread B (write or others) Thread C (shrinker)
->write_index
->clear_bit(DIRTY_NODE)
->clear_bit(COW_ZNODE)
This leads to situation where we have a diry page but no budget allocated for
this page, so further write-back may fail with -ENOSPC.
In this fix we return from page_mkwrite without performing unlock_page. We
return VM_FAULT_LOCKED instead. After doing this, the race above will not
happen.
Previously, the lower limit for the MIPS SC initialization loop was
set incorrectly allowing one extra loop leading to writes
beyond the MSC ioremap'd space. More precisely, the value of the 'imp'
in the last loop increased beyond the msc_irqmap_t boundaries and
as a result of which, the 'n' variable was loaded with an incorrect
value. This value was used later on to calculate the offset in the
MSC01_IC_SUP which led to random crashes like the following one:
CPU 0 Unable to handle kernel paging request at virtual address e75c0200,
epc == 8058dba4, ra == 8058db90
[...]
Call Trace:
[<8058dba4>] init_msc_irqs+0x104/0x154
[<8058b5bc>] arch_init_irq+0xd8/0x154
[<805897b0>] start_kernel+0x220/0x36c
Kernel panic - not syncing: Attempted to kill the idle task!
On MIPS calls to _mcount in modules generate 2 instructions to load
the _mcount address (and therefore 2 relocations). The mcount_loc
table should only reference the first of these, so the second is
filtered out by checking the relocation offset and ignoring ones that
immediately follow the previous one seen.
However if a module has an _mcount call at offset 0, the second
relocation would not be filtered out due to old_r_offset == 0
being taken to mean that the current relocation is the first one
seen, and both would end up in the mcount_loc table.
This results in ftrace_make_nop() patching both (adjacent)
instructions to branches over the _mcount call sequence like so:
The second branch is in the delay slot of the first, which is
defined to be unpredictable - on the platform on which this bug was
encountered, it triggers a reserved instruction exception.
Fix by initializing old_r_offset to ~0 and using that instead of 0
to determine whether the current relocation is the first seen.
Signed-off-by: Alex Smith <alex.smith@imgtec.com> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7098/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In module exit, dfs_parent and it's subtree were removed before
unregistering with pci. When debugfs entry for each device is attempted
to remove in pci_remove() context, they don't exist, as dfs_parent and
its children were already ripped apart.
Modified to first unregister with pci and then remove dfs_parent.
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A hardware quirk in P320h/P420m interfere with PCIe transactions on some
AMD chipsets, making P320h/P420m unusable. This workaround is to disable
ERO and NoSnoop bits in the parent and root complex for normal
functioning of these devices
NOTE: This workaround is specific to AMD chipset with a PCIe upstream
device with device id 0x5aXX
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com> Signed-off-by: Sam Bradshaw <sbradshaw@micron.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
3448a19da479 "vgaarb: use bridges to control VGA routing where possible"
added the "flags & PCI_VGA_STATE_CHANGE_DECODES" condition to an existing
WARN_ON(), but used bitwise AND (&) instead of logical AND (&&), so the
condition is never true. Replace with logical AND.
Found by Coverity (CID 142811).
Fixes: 3448a19da479 "vgaarb: use bridges to control VGA routing where possible" Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Yinghai Lu <yinghai@kernel.org> Acked-by: David Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The touchpad on the GIGABYTE U2442 not only stops communicating when we try
to set bit 3 (enable real hardware resolution) of reg_10, but on some BIOS
versions also when we set bit 1 (enable two finger mode auto correct).
I've asked the original reporter of:
https://bugzilla.kernel.org/show_bug.cgi?id=61151
To check that not setting bit 1 does not lead to any adverse effects on his
model / BIOS revision, and it does not, so this commit fixes the touchpad
not working on these versions by simply never setting bit 1 for laptop
models with the no_hw_res quirk.
Reported-and-tested-by: James Lademann <jwlademann@gmail.com> Tested-by: Philipp Wolfer <ph.wolfer@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is different from how (elantech) clickpads normally operate, normally
no matter where the user clicks on the pad the pad always reports a left
button event, since there is only 1 hardware button beneath the path.
It looks like Dell has put 2 buttons under the pad, one under each bottom
corner, causing this.
Since this however still clearly is a real clickpad hardware-wise, we still
want to report it as such to userspace, so that things like finger movement
in the bottom area can be properly ignored as it should be on clickpads.
So deal with this weirdness by simply mapping a right click to a left click
on elantech clickpads. As an added advantage this is something which we can
simply do on all elantech clickpads, so no need to add special quirks for
this weird model.
Reported-and-tested-by: Elder Marco <eldermarco@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a explicit memset to the login response PDU
exception path in iscsit_tx_login_rsp().
This addresses a regression bug introduced in commit baa4d64b
where the initiator would end up not receiving the login
response and associated status class + detail, before closing
the login connection.
This patch changes iscsit_check_dataout_hdr() to dump the incoming
Data-Out payload when the received ITT is not associated with a
WRITE, instead of calling iscsit_reject_cmd() for the non WRITE
ITT descriptor.
This addresses a bug where an initiator sending an Data-Out for
an ITT associated with a READ would end up generating a reject
for the READ, eventually resulting in list corruption.
This patch fixes a left-over se_lun->lun_sep pointer OOPs when one
of the /sys/kernel/config/target/$FABRIC/$WWPN/$TPGT/lun/$LUN/alua*
attributes is accessed after the $DEVICE symlink has been removed.
To address this bug, go ahead and clear se_lun->lun_sep memory in
core_dev_unexport(), so that the existing checks for show/store
ALUA attributes in target_core_fabric_configfs.c work as expected.
Reported-by: Sebastian Herbszt <herbszt@gmx.de> Tested-by: Sebastian Herbszt <herbszt@gmx.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roland Dreier [Mon, 30 Jun 2014 14:02:20 +0000 (07:02 -0700)]
iscsi-target: Re-add chunk from backport of upstream 79d59d08082d to 3.10
Commit d5c55fa31a29, the backport of upstream 79d59d08082d
("iscsi-target: Fix wrong buffer / buffer overrun in
iscsi_change_param_value()") left out applying one chunk of the fix in
iscsi_login_non_zero_tsih_s2(). Add the missing chunk.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bad syscall nr paths are their own incomprehensible route
through the entry control flow. Rearrange them to work just like
syscalls that return -ENOSYS.
This fixes an OOPS in the audit code when fast-path auditing is
enabled and sysenter gets a bad syscall nr (CVE-2014-4508).
This has probably been broken since Linux 2.6.27: af0575bba0 i386 syscall audit fast-path
There are 4 RDMA_CM events that all basically mean that
the user should teardown the IB connection:
- DISCONNECTED
- ADDR_CHANGE
- DEVICE_REMOVAL
- TIMEWAIT_EXIT
Only in DISCONNECTED/ADDR_CHANGE it makes sense to
call rdma_disconnect (send DREQ/DREP to our initiator).
So we keep the same teardown handler for all of them
but only indicate calling rdma_disconnect for the relevant
events.
This patch also removes redundant debug prints for each single
event.
v2 changes:
- Call isert_disconnected_handler() for DEVICE_REMOVAL (Or + Sag)
If this condition in end_extent_writepage() is false:
if (tree->ops && tree->ops->writepage_end_io_hook)
we will then test an uninitialized "ret" at:
ret = ret < 0 ? ret : -EIO;
The test for ret is for the case where ->writepage_end_io_hook
failed, and we'd choose that ret as the error; but if
there is no ->writepage_end_io_hook, nothing sets ret.
Initializing ret to 0 should be sufficient; if
writepage_end_io_hook wasn't set, (!uptodate) means
non-zero err was passed in, so we choose -EIO in that case.
Signed-of-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we are doing an incremental send and the base snapshot has a
directory with name X that doesn't exist anymore in the second
snapshot and a new subvolume/snapshot exists in the second snapshot
that has the same name as the directory (name X), the incremental
send would fail with -ENOENT error. This is because it attempts
to lookup for an inode with a number matching the objectid of a
root, which doesn't exist.
Reported-by: Robert White <rwhite@pobox.com> Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to commit 865ffef3797da2cac85b3354b5b6050dc9660978
(fs: fix fsync() error reporting),
it's not stable to just check error pages because pages can be
truncated or invalidated, we should also mark mapping with error
flag so that a later fsync can catch the error.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In close_ctree(), after we have stopped all workers,there maybe still
some read requests(for example readahead) to submit and this *maybe* trigger
an oops that user reported before:
kernel BUG at fs/btrfs/async-thread.c:619!
By hacking codes, i can reproduce this problem with one cpu available.
We fix this potential problem by invalidating all btree inode pages before
stopping all workers.
Thanks to Miao for pointing out this problem.
Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com> Reviewed-by: David Sterba <dsterba@suse.cz> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we fail to load a free space cache, we can rebuild it from the extent tree,
so it is not a serious error, we should not output a error message that
would make the users uncomfortable. This patch uses warning message instead
of it.
Btrfs will send uevent to udev inform the device change,
but ctime/mtime for the block device inode is not udpated, which cause
libblkid used by btrfs-progs unable to detect device change and use old
cache, causing 'btrfs dev scan; btrfs dev rmove; btrfs dev scan' give an
error message.
Reported-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com> Cc: Karel Zak <kzak@redhat.com> Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
skb_segment copies frags around, so we need
to copy them carefully to avoid accessing
user memory after reporting completion to userspace
through a callback.
skb_segment doesn't normally happen on datapath:
TSO needs to be disabled - so disabling zero copy
in this case does not look like a big deal.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2. As skb_segment() only supports page-frags *or* a
frag list, there is no need for the additional frag_skb pointer or the
preparatory renaming.] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Eddie Chapman <eddie@ehuk.net> # backported to 3.10 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A kernel memory disclosure was introduced in aio_read_events_ring() in v3.10
by commit a31ad380bed817aa25f8830ad23e1a0480fef797. The changes made to
aio_read_events_ring() failed to correctly limit the index into
ctx->ring_pages[], allowing an attacked to cause the subsequent kmap() of
an arbitrary page with a copy_to_user() to copy the contents into userspace.
This vulnerability has been assigned CVE-2014-0206. Thanks to Mateusz and
Petr for disclosing this issue.
This patch applies to v3.12+. A separate backport is needed for 3.10/3.11.
[jmoyer@redhat.com: backported to 3.10] Signed-off-by: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Cc: Mateusz Guzik <mguzik@redhat.com> Cc: Petr Matousek <pmatouse@redhat.com> Cc: Kent Overstreet <kmo@daterainc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The aio cleanups and optimizations by kmo that were merged into the 3.10
tree added a regression for userspace event reaping. Specifically, the
reference counts are not decremented if the event is reaped in userspace,
leading to the application being unable to submit further aio requests.
This patch applies to 3.12+. A separate backport is required for 3.10/3.11.
This issue was uncovered as part of CVE-2014-0206.
[jmoyer@redhat.com: backported to 3.10] Signed-off-by: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Cc: Kent Overstreet <kmo@daterainc.com> Cc: Mateusz Guzik <mguzik@redhat.com> Cc: Petr Matousek <pmatouse@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Till reported that the spurious interrupt detection of threaded
interrupts is broken in two ways:
- note_interrupt() is called for each action thread of a shared
interrupt line. That's wrong as we are only interested whether none
of the device drivers felt responsible for the interrupt, but by
calling multiple times for a single interrupt line we account
IRQ_NONE even if one of the drivers felt responsible.
- note_interrupt() when called from the thread handler is not
serialized. That leaves the members of irq_desc which are used for
the spurious detection unprotected.
To solve this we need to defer the spurious detection of a threaded
interrupt to the next hardware interrupt context where we have
implicit serialization.
If note_interrupt is called with action_ret == IRQ_WAKE_THREAD, we
check whether the previous interrupt requested a deferred check. If
not, we request a deferred check for the next hardware interrupt and
return.
If set, we check whether one of the interrupt threads signaled
success. Depending on this information we feed the result into the
spurious detector.
If one primary handler of a shared interrupt returns IRQ_HANDLED we
disable the deferred check of irq threads on the same line, as we have
found at least one device driver who cared.
Reported-by: Till Straumann <strauman@slac.stanford.edu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Austin Schuh <austin@peloton-tech.com> Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Pavel Pisa <pisa@cmp.felk.cvut.cz> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: linux-can@vger.kernel.org Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1303071450130.22263@ionos Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The io_setup takes a pointer to a context id of type aio_context_t.
This in turn is typed to a __kernel_ulong_t. We could tweak the
exported headers to define this as a 64bit quantity for specific
ABIs, but since we already have a 32bit compat shim for the x86 ABI,
let's just re-use that logic. The libaio package is also written to
expect this as a pointer type, so a compat shim would simplify that.
The io_submit func operates on an array of pointers to iocb structs.
Padding out the array to be 64bit aligned is a huge pain, so convert
it over to the existing compat shim too.
We don't convert io_getevents to the compat func as its only purpose
is to handle the timespec struct, and the x32 ABI uses 64bit times.
With this change, the libaio package can now pass its testsuite when
built for the x32 ABI.
It is not safe to use LAR to filter when to go down the espfix path,
because the LDT is per-process (rather than per-thread) and another
thread might change the descriptors behind our back. Fortunately it
is always *safe* (if a bit slow) to go down the espfix path, and a
32-bit LDT stack segment is extremely rare.
[Note that a different patch to address the same issue went in during
v3.15-rc1 (commit 4442dc8a), but includes a bunch of other changes that
don't strictly apply to fixing the bug]
This patch changes rd_allocate_sgl_table() to explicitly clear
ramdisk_mcp backend memory pages by passing __GFP_ZERO into
alloc_pages().
This addresses a potential security issue where reading from a
ramdisk_mcp could return sensitive information, and follows what
>= v3.15 does to explicitly clear ramdisk_mcp memory at backend
device initialization time.
Reported-by: Jorge Daniel Sequeira Matias <jdsm@tecnico.ulisboa.pt> Cc: Jorge Daniel Sequeira Matias <jdsm@tecnico.ulisboa.pt> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an initiator sends an allocation length bigger than what its
command consumes, the target should only return the actual response data
and set the residual length to the unused part of the allocation length.
Add a helper function that command handlers (INQUIRY, READ CAPACITY,
etc) can use to do this correctly, and use this code to get the correct
residual for commands that don't use the full initiator allocation in the
handlers for READ CAPACITY, READ CAPACITY(16), INQUIRY, MODE SENSE and
REPORT LUNS.
This addresses a handful of failures as reported by Christophe with
the Windows Certification Kit:
This patch fixes a iscsi_queue_req memory leak when ABORT_TASK response
has been queued by TFO->queue_tm_rsp() -> lio_queue_tm_rsp() after a
long standing I/O completes, but the connection has already reset and
waiting for cleanup to complete in iscsit_release_commands_from_conn()
-> transport_generic_free_cmd() -> transport_wait_for_tasks() code.
It moves iscsit_free_queue_reqs_for_conn() after the per-connection command
list has been released, so that the associated se_cmd tag can be completed +
released by target-core before freeing any remaining iscsi_queue_req memory
for the connection generated by lio_queue_tm_rsp().
Cc: Thomas Glanzmann <thomas@glanzmann.de> Cc: Charalampos Pournaris <charpour@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug where multiple waiters on ->t_transport_stop_comp
occurs due to a concurrent ABORT_TASK and session reset both invoking
transport_wait_for_tasks(), while waiting for the associated se_cmd
descriptor backend processing to complete.
For this case, complete_all() should be invoked in order to wake up
both waiters in core_tmr_abort_task() + transport_generic_free_cmd()
process contexts.
Cc: Thomas Glanzmann <thomas@glanzmann.de> Cc: Charalampos Pournaris <charpour@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
