According to the DP83865 datasheet "the 10 Mbps HDX loopback can be
disabled in the expanded memory register 0x1C0.1". The driver erroneously
used bit 0 instead of bit 1.
Fixes: 4621bf129856 ("phy: Add file missed in previous commit.") Signed-off-by: Peter Mamonov <pmamonov@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
add_early_randomness() is called by hwrng_register() when the
hardware is added. If this hardware and its module are present
at boot, and if there is no data available the boot hangs until
data are available and can't be interrupted.
For instance, in the case of virtio-rng, in some cases the host can be
not able to provide enough entropy for all the guests.
We can have two easy ways to reproduce the problem but they rely on
misconfiguration of the hypervisor or the egd daemon:
- if virtio-rng device is configured to connect to the egd daemon of the
host but when the virtio-rng driver asks for data the daemon is not
connected,
- if virtio-rng device is configured to connect to the egd daemon of the
host but the egd daemon doesn't provide data.
The guest kernel will hang at boot until the virtio-rng driver provides
enough data.
To avoid that, call rng_get_data() in non-blocking mode (wait=0)
from add_early_randomness().
Signed-off-by: Laurent Vivier <lvivier@redhat.com> Fixes: d9e797261933 ("hwrng: add randomness to system from rng...") Reviewed-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In hypfs_fill_super(), if hypfs_create_update_file() fails,
sbi->update_file is left holding an error number. This is passed to
hypfs_kill_super() which doesn't check for this.
Fix this by not setting sbi->update_value until after we've checked for
error.
Fixes: 24bbb1faf3f0 ("[PATCH] s390_hypfs filesystem") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
cc: Heiko Carstens <heiko.carstens@de.ibm.com>
cc: linux-s390@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
prep_irq_for_idle() is intended to be called before entering
H_CEDE (and it is used by the pseries cpuidle driver). However the
default pseries idle routine does not call it, leading to mismanaged
lazy irq state when the cpuidle driver isn't in use. Manifestations of
this include:
* Dropped IPIs in the time immediately after a cpu comes
online (before it has installed the cpuidle handler), making the
online operation block indefinitely waiting for the new cpu to
respond.
* Hitting this WARN_ON in arch_local_irq_restore():
/*
* We should already be hard disabled here. We had bugs
* where that wasn't the case so let's dbl check it and
* warn if we are wrong. Only do that when IRQ tracing
* is enabled as mfmsr() can be costly.
*/
if (WARN_ON_ONCE(mfmsr() & MSR_EE))
__hard_irq_disable();
Call prep_irq_for_idle() from pseries_lpar_idle() and honor its
result.
Fixes: 363edbe2614a ("powerpc: Default arch idle could cede processor on pseries") Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20190910225244.25056-1-nathanl@linux.ibm.com Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Configfs abuses symlink(2). Unlike the normal filesystems, it
wants the target resolved at symlink(2) time, like link(2) would've
done. The problem is that ->symlink() is called with the parent
directory locked exclusive, so resolving the target inside the
->symlink() is easily deadlocked.
Short of really ugly games in sys_symlink() itself, all we can
do is to unlock the parent before resolving the target and
relock it after. However, that invalidates the checks done
by the caller of ->symlink(), so we have to
* check that dentry is still where it used to be
(it couldn't have been moved, but it could've been unhashed)
* recheck that it's still negative (somebody else
might've successfully created a symlink with the same name
while we were looking the target up)
* recheck the permissions on the parent directory.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Christoph Hellwig <hch@lst.de>
[bwh: Backported to 3.16: open-code inode_{,un}lock()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently frame registrations are not purged, even when changing the
interface type. This can lead to potentially weird situations where
frames possibly not allowed on a given interface type remain registered
due to the type switching happening after registration.
The kernel currently relies on userspace apps to actually purge the
registrations themselves, this is not something that the kernel should
rely on.
Add a call to cfg80211_mlme_purge_registrations() to forcefully remove
any registrations left over prior to switching the iftype.
Manually generate the PDPTR reserved bit mask when explicitly loading
PDPTRs. The reserved bits that are being tracked by the MMU reflect the
current paging mode, which is unlikely to be PAE paging in the vast
majority of flows that use load_pdptrs(), e.g. CR0 and CR4 emulation,
__set_sregs(), etc... This can cause KVM to incorrectly signal a bad
PDPTR, or more likely, miss a reserved bit check and subsequently fail
a VM-Enter due to a bad VMCS.GUEST_PDPTR.
Add a one off helper to generate the reserved bits instead of sharing
code across the MMU's calculations and the PDPTR emulation. The PDPTR
reserved bits are basically set in stone, and pushing a helper into
the MMU's calculation adds unnecessary complexity without improving
readability.
Oppurtunistically fix/update the comment for load_pdptrs().
Note, the buggy commit also introduced a deliberate functional change,
"Also remove bit 5-6 from rsvd_bits_mask per latest SDM.", which was
effectively (and correctly) reverted by commit cd9ae5fe47df ("KVM: x86:
Fix page-tables reserved bits"). A bit of SDM archaeology shows that
the SDM from late 2008 had a bug (likely a copy+paste error) where it
listed bits 6:5 as AVL and A for PDPTEs used for 4k entries but reserved
for 2mb entries. I.e. the SDM contradicted itself, and bits 6:5 are and
always have been reserved.
Fixes: 20c466b56168d ("KVM: Use rsvd_bits_mask in load_pdptrs()") Cc: Nadav Amit <nadav.amit@gmail.com> Reported-by: Doug Reiland <doug.reiland@intel.com> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Reviewed-by: Peter Xu <peterx@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Just reuse rsvd_bits() inside kvm_set_mmio_spte_mask()
for slightly better code.
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.16 as dependency of commit 16cfacc80857
"KVM: x86: Manually calculate reserved bits when loading PDPTRS"] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When doing any form of incremental send the parent and the child trees
need to be compared via btrfs_compare_trees. This can result in long
loop chains without ever relinquishing the CPU. This causes softlockup
detector to trigger when comparing trees with a lot of items. Example
report:
At ctree.c:get_old_root(), we are accessing a root's header owner field
after we have freed the respective extent buffer. This results in an
use-after-free that can lead to crashes, and when CONFIG_DEBUG_PAGEALLOC
is set, results in a stack trace like the following:
Fix that by saving the root's header owner field into a local variable
before freeing the root's extent buffer, and then use that local variable
when needed.
Fixes: 30b0463a9394d9 ("Btrfs: fix accessing the root pointer in tree mod log functions") Reviewed-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The HP Dino PCI controller chip can be used in two variants: as on-board
controller (e.g. in B160L), or on an Add-On card ("Card-Mode") to bridge
PCI components to systems without a PCI bus, e.g. to a HSC/GSC bus. One
such Add-On card is the HP HSC-PCI Card which has one or more DEC Tulip
PCI NIC chips connected to the on-card Dino PCI controller.
Dino in Card-Mode has a big disadvantage: All PCI memory accesses need
to go through the DINO_MEM_DATA register, so Linux drivers will not be
able to use the ioremap() function. Without ioremap() many drivers will
not work, one example is the tulip driver which then simply crashes the
kernel if it tries to access the ports on the HP HSC card.
This patch disables the HP HSC card if it finds one, and as such
fixes the kernel crash on a HP D350/2 machine.
Signed-off-by: Helge Deller <deller@gmx.de> Noticed-by: Phil Scarr <phil.scarr@pm.me> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The syzbot fuzzer provoked a general protection fault in the
hid-prodikeys driver:
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.3.0-rc5+ #28
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
RIP: 0010:pcmidi_submit_output_report drivers/hid/hid-prodikeys.c:300 [inline]
RIP: 0010:pcmidi_set_operational drivers/hid/hid-prodikeys.c:558 [inline]
RIP: 0010:pcmidi_snd_initialise drivers/hid/hid-prodikeys.c:686 [inline]
RIP: 0010:pk_probe+0xb51/0xfd0 drivers/hid/hid-prodikeys.c:836
Code: 0f 85 50 04 00 00 48 8b 04 24 4c 89 7d 10 48 8b 58 08 e8 b2 53 e4 fc
48 8b 54 24 20 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <80> 3c 02 00 0f
85 13 04 00 00 48 ba 00 00 00 00 00 fc ff df 49 8b
The problem is caused by the fact that pcmidi_get_output_report() will
return an error if the HID device doesn't provide the right sort of
output report, but pcmidi_set_operational() doesn't bother to check
the return code and assumes the function call always succeeds.
This patch adds the missing check and aborts the probe operation if
necessary.
Reported-and-tested-by: syzbot+1088533649dafa1c9004@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
inode_smack::smk_lock is taken during smack_d_instantiate(), which is
called during a filesystem transaction when creating a file on ext4.
Therefore to avoid a deadlock, all code that takes this lock must use
GFP_NOFS, to prevent memory reclaim from waiting for the filesystem
transaction to complete.
Reported-by: syzbot+0eefc1e06a77d327a056@syzkaller.appspotmail.com Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
[bwh: Backported to 3.16:
- Drop change to smk_netlbl_mls(), where GFP_ATOMIC is used
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
There is a logic bug in the current smack_bprm_set_creds():
If LSM_UNSAFE_PTRACE is set, but the ptrace state is deemed to be
acceptable (e.g. because the ptracer detached in the meantime), the other
->unsafe flags aren't checked. As far as I can tell, this means that
something like the following could work (but I haven't tested it):
- task A: create task B with fork()
- task B: set NO_NEW_PRIVS
- task B: install a seccomp filter that makes open() return 0 under some
conditions
- task B: replace fd 0 with a malicious library
- task A: attach to task B with PTRACE_ATTACH
- task B: execve() a file with an SMACK64EXEC extended attribute
- task A: while task B is still in the middle of execve(), exit (which
destroys the ptrace relationship)
Make sure that if any flags other than LSM_UNSAFE_PTRACE are set in
bprm->unsafe, we reject the execve().
Fixes: 5663884caab1 ("Smack: unify all ptrace accesses in the smack") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
[bwh: Backported to 3.16: Ignore LSM_UNSAFE_PTRACE_CAP, which is also handled
by the preceding if-statement.] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The error occurs when the descriptors_changed() routine (called during
a device reset) attempts to compare the old and new BOS and capability
descriptors. The length it uses for the comparison is the
wTotalLength value stored in BOS descriptor, but this value is not
necessarily the same as the length actually allocated for the
descriptors. If it is larger the routine will call memcmp() with a
length that is too big, thus reading beyond the end of the allocated
region and leading to this fault.
The kernel reads the BOS descriptor twice: first to get the total
length of all the capability descriptors, and second to read it along
with all those other descriptors. A malicious (or very faulty) device
may send different values for the BOS descriptor fields each time.
The memory area will be allocated using the wTotalLength value read
the first time, but stored within it will be the value read the second
time.
To prevent this possibility from causing any errors, this patch
modifies the BOS descriptor after it has been read the second time:
It sets the wTotalLength field to the actual length of the descriptors
that were read in and validated. Then the memcpy() call, or any other
code using these descriptors, will be able to rely on wTotalLength
being valid.
syzbot found that a thread can stall for minutes inside read_mem() or
write_mem() after that thread was killed by SIGKILL [1]. Reading from
iomem areas of /dev/mem can be slow, depending on the hardware.
While reading 2GB at one read() is legal, delaying termination of killed
thread for minutes is bad. Thus, allow reading/writing /dev/mem and
/dev/kmem to be preemptible and killable.
Theoretically, reading/writing /dev/mem and /dev/kmem can become
"interruptible". But this patch chose "killable". Future patch will make
them "interruptible" so that we can revert to "killable" if some program
regressed.
As reported by the OpenWRT team, write requests sometimes fail on some
platforms.
Currently to check the state chip_ready() is used correctly as described by
the flash memory S29GL256P11TFI01 datasheet.
Also chip_good() is used to check if the write is succeeded and it was
implemented by the commit fb4a90bfcd6d8 ("[MTD] CFI-0002 - Improve error
checking").
But actually the write failure is caused on some platforms and also it can
be fixed by using chip_good() to check the state and retry instead.
Also it seems that it is caused after repeated about 1,000 times to retry
the write one word with the reset command.
By using chip_good() to check the state to be done it can be reduced the
retry with reset.
It is depended on the actual flash chip behavior so the root cause is
unknown.
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com> Cc: linux-mtd@lists.infradead.org Reported-by: Fabio Bettoni <fbettoni@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
[vigneshr@ti.com: Fix a checkpatch warning] Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
[bwh: Backported to 3.16:
- chip_good() doesn't take a chip parameter
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Really enable warning when CONFIG_EXT4_DEBUG is set and fix missing
first argument. This was introduced in commit ff95ec22cd7f ("ext4:
add warning to ext4_convert_unwritten_extents_endio") and splitting
extents inside endio would trigger it.
Fixes: ff95ec22cd7f ("ext4: add warning to ext4_convert_unwritten_extents_endio") Signed-off-by: Rakesh Pandit <rakesh@tuxera.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The syzbot fuzzer has reported a pair of problems in the
hidraw_ioctl() function: slab-out-of-bounds read and use-after-free
read. An example of the first:
BUG: KASAN: slab-out-of-bounds in strlen+0x79/0x90 lib/string.c:525
Read of size 1 at addr ffff8881c8035f38 by task syz-executor.4/2833
This sets cpu 7 online in all respects except for the cpu's
corresponding struct device; dev->offline remains true.
3. Set cpu 7 online via sysfs. _cpu_up() determines that cpu 7 is
already online and returns success. The driver core (device_online)
sets dev->offline = false.
4. The migration completes and restores cpu 7 to offline state:
This leaves cpu7 in a state where the driver core considers the cpu
device online, but in all other respects it is offline and
unused. Attempts to online the cpu via sysfs appear to succeed but the
driver core actually does not pass the request to the lower-level
cpuhp support code. This makes the cpu unusable until the cpu device
is manually set offline and then online again via sysfs.
Instead of directly calling cpu_up/cpu_down, the migration code should
use the higher-level device core APIs to maintain consistent state and
serialize operations.
Fixes: 120496ac2d2d ("powerpc: Bring all threads online prior to migration/hibernation") Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com> Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20190802192926.19277-2-nathanl@linux.ibm.com Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This fixes a kernel panic on memcpy when
FORTIFY_SOURCE is enabled.
The initial smp implementation on commit aa7eb2bb4e4a
("arm: zynq: Add smp support")
used memcpy, which worked fine until commit ee333554fed5
("ARM: 8749/1: Kconfig: Add ARCH_HAS_FORTIFY_SOURCE")
enabled overflow checks at runtime, producing a read
overflow panic.
Currently when the call to ext4_htree_store_dirent fails the error return
variable 'ret' is is not being set to the error code and variable count is
instead, hence the error code is not being returned. Fix this by assigning
ret to the error return code.
Addresses-Coverity: ("Unused value") Fixes: 8af0f0822797 ("ext4: fix readdir error in the case of inline_data+dir_index") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
AER info of PCIe fatal error is not printed in the current driver.
Because APEI driver will panic directly for fatal error, and can't
run to the place of printing AER info.
An example log is as following:
{763}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 11
{763}[Hardware Error]: event severity: fatal
{763}[Hardware Error]: Error 0, type: fatal
{763}[Hardware Error]: section_type: PCIe error
{763}[Hardware Error]: port_type: 0, PCIe end point
{763}[Hardware Error]: version: 4.0
{763}[Hardware Error]: command: 0x0000, status: 0x0010
{763}[Hardware Error]: device_id: 0000:82:00.0
{763}[Hardware Error]: slot: 0
{763}[Hardware Error]: secondary_bus: 0x00
{763}[Hardware Error]: vendor_id: 0x8086, device_id: 0x10fb
{763}[Hardware Error]: class_code: 000002
Kernel panic - not syncing: Fatal hardware error!
This issue was imported by the patch, '37448adfc7ce ("aerdrv: Move
cper_print_aer() call out of interrupt context")'. To fix this issue,
this patch adds print of AER info in cper_print_pcie() for fatal error.
Here is the example log after this patch applied:
{24}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 10
{24}[Hardware Error]: event severity: fatal
{24}[Hardware Error]: Error 0, type: fatal
{24}[Hardware Error]: section_type: PCIe error
{24}[Hardware Error]: port_type: 0, PCIe end point
{24}[Hardware Error]: version: 4.0
{24}[Hardware Error]: command: 0x0546, status: 0x4010
{24}[Hardware Error]: device_id: 0000:01:00.0
{24}[Hardware Error]: slot: 0
{24}[Hardware Error]: secondary_bus: 0x00
{24}[Hardware Error]: vendor_id: 0x15b3, device_id: 0x1019
{24}[Hardware Error]: class_code: 000002
{24}[Hardware Error]: aer_uncor_status: 0x00040000, aer_uncor_mask: 0x00000000
{24}[Hardware Error]: aer_uncor_severity: 0x00062010
{24}[Hardware Error]: TLP Header: 000000c0010100000000000100000000
Kernel panic - not syncing: Fatal hardware error!
Fixes: 37448adfc7ce ("aerdrv: Move cper_print_aer() call out of interrupt context") Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Reviewed-by: James Morse <james.morse@arm.com>
[ardb: put parens around terms of && operator] Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A lot of places in the driver use onyx_read_register() without
checking the return value, and it's been working OK for ~10 years
or so, so probably never fails ... Rather than trying to check the
return value everywhere, which would be relatively intrusive, at
least make sure we don't use an uninitialized value.
Fixes: f3d9478b2ce4 ("[ALSA] snd-aoa: add snd-aoa") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
From code inspection it can be seen that of_get_display_timing() is
lacking an of_node_put(). Add it.
Fixes: ffa3fd21de8a ("videomode: implement public of_get_display_timing()") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: David Airlie <airlied@linux.ie> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190722182439.44844-2-dianders@chromium.org Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A reboot request sends an IPI via the reboot vector and waits for all other
CPUs to stop. If one or more CPUs are in critical regions with interrupts
disabled then the IPI is not handled on those CPUs and the shutdown hangs
if native_stop_other_cpus() is called with the wait argument set.
Such a situation can happen when one CPU was stopped within a lock held
section and another CPU is trying to acquire that lock with interrupts
disabled. There are other scenarios which can cause such a lockup as well.
In theory the shutdown should be attempted by an NMI IPI after the timeout
period elapsed. Though the wait loop after sending the reboot vector IPI
prevents this. It checks the wait request argument and the timeout. If wait
is set, which is true for sys_reboot() then it won't fall through to the
NMI shutdown method after the timeout period has finished.
This was an oversight when the NMI shutdown mechanism was added to handle
the 'reboot IPI is not working' situation. The mechanism was added to deal
with stuck panic shutdowns, which do not have the wait request set, so the
'wait request' case was probably not considered.
Remove the wait check from the post reboot vector IPI wait loop and enforce
that the wait loop in the NMI fallback path is invoked even if NMI IPIs are
disabled or the registration of the NMI handler fails. That second wait
loop will then hang if not all CPUs shutdown and the wait argument is set.
[ tglx: Avoid the hard to parse line break in the NMI fallback path,
add comments and massage the changelog ]
Fixes: 7d007d21e539 ("x86/reboot: Use NMI to assist in shutting down if IRQ fails") Signed-off-by: Grzegorz Halat <ghalat@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Don Zickus <dzickus@redhat.com> Link: https://lkml.kernel.org/r/20190628122813.15500-1-ghalat@redhat.com Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
It seems we should use 'range' instead of 'priv->range'
in lbtf_geo_init(), because 'range' is the corret one
related to current regioncode.
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 691cdb49388b ("libertas_tf: command helper functions for libertas_tf") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The page_offset was only applied to the end of the page range. This caused
the display updates to cause a scrolling effect on the display because the
amount of data written to the display did not match the range display
expected.
Fixes: 301bc0675b67 ("video: ssd1307fb: Make use of horizontal addressing mode") Signed-off-by: Marko Kohtala <marko.kohtala@okoko.fi> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Michal Vokáč <michal.vokac@ysoft.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190618074111.9309-4-marko.kohtala@okoko.fi Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When CONFIG_DVB_DIB9000 is disabled, we can still compile code that
now fails to link against dibx000_i2c_set_speed:
drivers/media/usb/dvb-usb/dib0700_devices.o: In function `dib01x0_pmu_update.constprop.7':
dib0700_devices.c:(.text.unlikely+0x1c9c): undefined reference to `dibx000_i2c_set_speed'
The call sites are both through dib01x0_pmu_update(), which gets passed
an 'i2c' pointer from dib9000_get_i2c_master(), which has returned
NULL. Checking this pointer seems to be a good idea anyway, and it avoids
the link failure in most cases.
Sean Young found another case that is not fixed by that, where certain
gcc versions leave an unused function in place that causes the link error,
but adding an explict IS_ENABLED() check also solves this.
Fixes: b7f54910ce01 ("V4L/DVB (4647): Added module for DiB0700 based devices") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Firmware files are in ASCII, using 2 hex characters per byte. The
maximum length of a firmware string is therefore
16 (commands) * 2 (bytes per command) * 2 (characters per byte) = 64
Fixes: ff45262a85db ("leds: add new LP5562 LED driver") Signed-off-by: Nick Stoughton <nstoughton@logitech.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
VAG power control is improved to fit the manual [1]. This patch fixes as
minimum one bug: if customer muxes Headphone to Line-In right after boot,
the VAG power remains off that leads to poor sound quality from line-in.
I.e. after boot:
- Connect sound source to Line-In jack;
- Connect headphone to HP jack;
- Run following commands:
$ amixer set 'Headphone' 80%
$ amixer set 'Headphone Mux' LINE_IN
Change VAG power on/off control according to the following algorithm:
- turn VAG power ON on the 1st incoming event.
- keep it ON if there is any active VAG consumer (ADC/DAC/HP/Line-In).
- turn VAG power OFF when there is the latest consumer's pre-down event
come.
- always delay after VAG power OFF to avoid pop.
- delay after VAG power ON if the initiative consumer is Line-In, this
prevents pop during line-in muxing.
According to the data sheet [1], to avoid any pops/clicks,
the outputs should be muted during input/output
routing changes.
When power up, a "pop" is heard on line-in and mic-in.
An analysis of the PCM shows it lasts ~400ms
and looks like a filter response.
VAG power up should be delayed by 400ms as VAG power down is.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@veo-labs.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 92e222df7b "btrfs: alloc_chunk: fix DUP stripe size handling"
fixed calculating the stripe_size for a new DUP chunk.
However, the same calculation reappears a bit later, and that one was
not changed yet. The resulting bug that is exposed is that the newly
allocated device extents ('stripes') can have a few MiB overlap with the
next thing stored after them, which is another device extent or the end
of the disk.
The scenario in which this can happen is:
* The block device for the filesystem is less than 10GiB in size.
* The amount of contiguous free unallocated disk space chosen to use for
chunk allocation is 20% of the total device size, or a few MiB more or
less.
An example:
- The filesystem device is 7880MiB (max_chunk_size gets set to 788MiB)
- There's 1578MiB unallocated raw disk space left in one contiguous
piece.
In this case stripe_size is first calculated as 789MiB, (half of
1578MiB).
Since 789MiB (stripe_size * data_stripes) > 788MiB (max_chunk_size), we
enter the if block. Now stripe_size value is immediately overwritten
while calculating an adjusted value based on max_chunk_size, which ends
up as 788MiB.
Next, the value is rounded up to a 16MiB boundary, 800MiB, which is
actually more than the value we had before. However, the last comparison
fails to detect this, because it's comparing the value with the total
amount of free space, which is about twice the size of stripe_size.
In the example above, this means that the resulting raw disk space being
allocated is 1600MiB, while only a gap of 1578MiB has been found. The
second device extent object for this DUP chunk will overlap for 22MiB
with whatever comes next.
The underlying problem here is that the stripe_size is reused all the
time for different things. So, when entering the code in the if block,
stripe_size is immediately overwritten with something else. If later we
decide we want to have the previous value back, then the logic to
compute it was copy pasted in again.
With this change, the value in stripe_size is not unnecessarily
destroyed, so the duplicated calculation is not needed any more.
Signed-off-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cleanup the following things:
1) open coded SZ_16M round up
2) use min() to replace open-coded size comparison
3) code style
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: Gu Jinxiang <gujx@cn.fujitsu.com>
[ reformat comment ] Signed-off-by: David Sterba <dsterba@suse.com>
[bwh: Backported to 3.16 as dependency of commit baf92114c7
"btrfs: alloc_chunk: fix more DUP stripe size handling":
- Add #include <linux/sizes.h> for definition of SZ_16M] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Hans van Kranenburg <hans.van.kranenburg@mendix.com>
The problem is that any 'uptodate' vs 'disks' check is not precise
in this path. Put a "WARN_ON(!test_bit(R5_UPTODATE, &dev->flags)" on the
device that might try to kick off writes and then skip the action.
Better to prevent the raid driver from taking unexpected action *and* keep
the system alive vs killing the machine with BUG_ON.
Note: fixed warning reported by kbuild test robot <lkp@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Nigel Croxon <ncroxon@redhat.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently the code assumes that if a file info entry belongs
to lists of open file handles of an inode and a tcon then
it has non-zero reference. The recent changes broke that
assumption when putting the last reference of the file info.
There may be a situation when a file is being deleted but
nothing prevents another thread to reference it again
and start using it. This happens because we do not hold
the inode list lock while checking the number of references
of the file info structure. Fix this by doing the proper
locking when doing the check.
Fixes: 487317c99477d ("cifs: add spinlock for the openFileList to cifsInodeInfo") Fixes: cb248819d209d ("cifs: use cifsInodeInfo->open_file_lock while iterating to avoid a panic") Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 487317c99477 ("cifs: add spinlock for the openFileList to
cifsInodeInfo") added cifsInodeInfo->open_file_lock spin_lock to protect
the openFileList, but missed a few places where cifs_inode->openFileList
was enumerated. Change these remaining tcon->open_file_lock to
cifsInodeInfo->open_file_lock to avoid panic in is_size_safe_to_change.
Fixes: 487317c99477 ("cifs: add spinlock for the openFileList to cifsInodeInfo") Signed-off-by: Dave Wysochanski <dwysocha@redhat.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Pavel Shilovskiy <pshilov@microsoft.com>
ENOTSUPP is not supposed to be returned to userspace. This was found on an
OpenPower machine, where the RTC does not support set_alarm.
On that system, a clock_nanosleep(CLOCK_REALTIME_ALARM, ...) results in
"524 Unknown error 524"
Replace it with EOPNOTSUPP which results in the expected "95 Operation not
supported" error.
Fixes: 1c6b39ad3f01 (alarmtimers: Return -ENOTSUPP if no RTC device is present) Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190903171802.28314-1-cascardo@canonical.com
[ pvorel: backport for v3.16, changes also in alarm_timer_{del,set}(), which
were removed in f2c45807d3992fe0f173f34af9c347d907c31686 in v4.13-rc1 ] Signed-off-by: Petr Vorel <pvorel@suse.cz> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The PCI Tegra controller conversion to a device tree configurable
driver in commit d1523b52bff3 ("PCI: tegra: Move PCIe driver
to drivers/pci/host") implied that code for the driver can be
compiled in for a kernel supporting multiple platforms.
Unfortunately, a blind move of the code did not check that some of the
quirks that were applied in arch/arm (eg enabling Relaxed Ordering on
all PCI devices - since the quirk hook erroneously matches PCI_ANY_ID
for both Vendor-ID and Device-ID) are now applied in all kernels that
compile the PCI Tegra controlled driver, DT and ACPI alike.
This is completely wrong, in that enablement of Relaxed Ordering is only
required by default in Tegra20 platforms as described in the Tegra20
Technical Reference Manual (available at
https://developer.nvidia.com/embedded/downloads#?search=tegra%202 in
Section 34.1, where it is mentioned that Relaxed Ordering bit needs to
be enabled in its root ports to avoid deadlock in hardware) and in the
Tegra30 platforms for the same reasons (unfortunately not documented
in the TRM).
There is no other strict requirement on PCI devices Relaxed Ordering
enablement on any other Tegra platforms or PCI host bridge driver.
Fix this quite upsetting situation by limiting the vendor and device IDs
to which the Relaxed Ordering quirk applies to the root ports in
question, reported above.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
[lorenzo.pieralisi@arm.com: completely rewrote the commit log/fixes tag] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Emulation of VMPTRST can incorrectly inject a page fault
when passed an operand that points to an MMIO address.
The page fault will use uninitialized kernel stack memory
as the CR2 and error code.
The right behavior would be to abort the VM with a KVM_EXIT_INTERNAL_ERROR
exit to userspace; however, it is not an easy fix, so for now just ensure
that the error code and CR2 are zero.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
[add comment] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In event of failure during register_netdevice, free_netdev is
invoked immediately. free_netdev assumes that all the netdevice
refcounts have been dropped prior to it being called and as a
result frees and clears out the refcount pointer.
However, this is not necessarily true as some of the operations
in the NETDEV_UNREGISTER notifier handlers queue RCU callbacks for
invocation after a grace period. The IPv4 callback in_dev_rcu_put
tries to access the refcount after free_netdev is called which
leads to a null de-reference-
Fix this by waiting for the completion of the call_rcu() in
case of register_netdevice errors.
Fixes: 93ee31f14f6f ("[NET]: Fix free_netdev on register_netdev failure.") Cc: Sean Tranchetti <stranche@codeaurora.org> Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The '.exit' functions from 'pernet_operations' structure should be marked
as __net_exit, not __net_init.
Fixes: d862e5461423 ("net: ipv6: Implement /proc/net/icmp6.") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
tun_chr_read_iter() accessed the memory which freed by free_netdev()
called by tun_set_iff():
CPUA CPUB
tun_set_iff()
alloc_netdev_mqs()
tun_attach()
tun_chr_read_iter()
tun_get()
tun_do_read()
tun_ring_recv()
register_netdevice() <-- inject error
goto err_detach
tun_detach_all() <-- set RCV_SHUTDOWN
free_netdev() <-- called from
err_free_dev path
netdev_freemem() <-- free the memory
without check refcount
(In this path, the refcount cannot prevent
freeing the memory of dev, and the memory
will be used by dev_put() called by
tun_chr_read_iter() on CPUB.)
(Break from tun_ring_recv(),
because RCV_SHUTDOWN is set)
tun_put()
dev_put() <-- use the memory
freed by netdev_freemem()
Put the publishing of tfile->tun after register_netdevice(),
so tun_get() won't get the tun pointer that freed by
err_detach path if register_netdevice() failed.
Fixes: eb0fb363f920 ("tuntap: attach queue 0 before registering netdevice") Reported-by: Hulk Robot <hulkci@huawei.com> Suggested-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fix tcp_ecn_withdraw_cwr() to clear the correct bit:
TCP_ECN_QUEUE_CWR.
Rationale: basically, TCP_ECN_DEMAND_CWR is a bit that is purely about
the behavior of data receivers, and deciding whether to reflect
incoming IP ECN CE marks as outgoing TCP th->ece marks. The
TCP_ECN_QUEUE_CWR bit is purely about the behavior of data senders,
and deciding whether to send CWR. The tcp_ecn_withdraw_cwr() function
is only called from tcp_undo_cwnd_reduction() by data senders during
an undo, so it should zero the sender-side state,
TCP_ECN_QUEUE_CWR. It does not make sense to stop the reflection of
incoming CE bits on incoming data packets just because outgoing
packets were spuriously retransmitted.
The bug has been reproduced with packetdrill to manifest in a scenario
with RFC3168 ECN, with an incoming data packet with CE bit set and
carrying a TCP timestamp value that causes cwnd undo. Before this fix,
the IP CE bit was ignored and not reflected in the TCP ECE header bit,
and sender sent a TCP CWR ('W') bit on the next outgoing data packet,
even though the cwnd reduction had been undone. After this fix, the
sender properly reflects the CE bit and does not set the W bit.
Note: the bug actually predates 2005 git history; this Fixes footer is
chosen to be the oldest SHA1 I have tested (from Sep 2007) for which
the patch applies cleanly (since before this commit the code was in a
.h file).
Fixes: bdf1ee5d3bd3 ("[TCP]: Move code from tcp_ecn.h to tcp*.c and tcp.h & remove it") Signed-off-by: Neal Cardwell <ncardwell@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If a request_key authentication token key gets revoked, there's a window in
which request_key_auth_describe() can see it with a NULL payload - but it
makes no check for this and something like the following oops may occur:
Fix this by checking for a NULL pointer when describing such a key.
Also make the read routine check for a NULL pointer to be on the safe side.
[DH: Modified to not take already-held rcu lock and modified to also check
in the read routine]
Fixes: 04c567d9313e ("[PATCH] Keys: Fix race between two instantiators of a key") Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com> Signed-off-by: Hillf Danton <hdanton@sina.com> Signed-off-by: David Howells <dhowells@redhat.com> Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Unable to handle kernel NULL pointer dereference at 0000000000000158
Internal error: Oops: 96000004 [#1] SMP
pc : resend_irqs+0x68/0xb0
lr : resend_irqs+0x64/0xb0
...
Call trace:
resend_irqs+0x68/0xb0
tasklet_action_common.isra.6+0x84/0x138
tasklet_action+0x2c/0x38
__do_softirq+0x120/0x324
run_ksoftirqd+0x44/0x60
smpboot_thread_fn+0x1ac/0x1e8
kthread+0x134/0x138
ret_from_fork+0x10/0x18
The reason for this is that the interrupt resend mechanism happens in soft
interrupt context, which is a asynchronous mechanism versus other
operations on interrupts. free_irq() does not take resend handling into
account. Thus, the irq descriptor might be already freed before the resend
tasklet is executed. resend_irqs() does not check the return value of the
interrupt descriptor lookup and derefences the return value
unconditionally.
Transport should use its own pf_retrans to do the error_count
check, instead of asoc's. Otherwise, it's meaningless to make
pf_retrans per transport.
Fixes: 5aa93bcf66f4 ("sctp: Implement quick failover draft from tsvwg") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Since vhost_exceeds_weight() was introduced, callers need to specify
the packet weight and byte weight in vhost_dev_init(). Note that, the
packet weight isn't counted in this patch to keep the original behavior
unchanged.
Fixes: e82b9b0727ff ("vhost: introduce vhost_exceeds_weight()") Signed-off-by: Tiwei Bie <tiwei.bie@intel.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com>
[bwh: Backported to 3.16: vhost_dev_init() still doesn't take an iov_limit
parameter.] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
do_sched_cfs_period_timer() will refill cfs_b runtime and call
distribute_cfs_runtime to unthrottle cfs_rq, sometimes cfs_b->runtime
will allocate all quota to one cfs_rq incorrectly, then other cfs_rqs
attached to this cfs_b can't get runtime and will be throttled.
We find that one throttled cfs_rq has non-negative
cfs_rq->runtime_remaining and cause an unexpetced cast from s64 to u64
in snippet:
The runtime here will change to a large number and consume all
cfs_b->runtime in this cfs_b period.
According to Ben Segall, the throttled cfs_rq can have
account_cfs_rq_runtime called on it because it is throttled before
idle_balance, and the idle_balance calls update_rq_clock to add time
that is accounted to the task.
This commit prevents cfs_rq to be assgined new runtime if it has been
throttled until that distribute_cfs_runtime is called.
Signed-off-by: Liangyan <liangyan.peng@linux.alibaba.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Valentin Schneider <valentin.schneider@arm.com> Reviewed-by: Ben Segall <bsegall@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: shanpeic@linux.alibaba.com Cc: xlpang@linux.alibaba.com Fixes: d3d9dc330236 ("sched: Throttle entities exceeding their allowed bandwidth") Link: https://lkml.kernel.org/r/20190826121633.6538-1-liangyan.peng@linux.alibaba.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.16: Open-code SCHED_WARN_ON().] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In commit 99cd149efe82 ("sgiseeq: replace use of dma_cache_wback_inv"),
a call to 'get_zeroed_page()' has been turned into a call to
'dma_alloc_coherent()'. Only the remove function has been updated to turn
the corresponding 'free_page()' into 'dma_free_attrs()'.
The error hndling path of the probe function has not been updated.
Fix it now.
Rename the corresponding label to something more in line.
Fixes: 99cd149efe82 ("sgiseeq: replace use of dma_cache_wback_inv") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The OCR register defines the supported range of VDD voltages for SD cards.
However, it has turned out that some SD cards reports an invalid voltage
range, for example having bit7 set.
When a host supports MMC_CAP2_FULL_PWR_CYCLE and some of the voltages from
the invalid VDD range, this triggers the core to run a power cycle of the
card to try to initialize it at the lowest common supported voltage.
Obviously this fails, since the card can't support it.
Let's fix this problem, by clearing invalid bits from the read OCR register
for SD cards, before proceeding with the VDD voltage negotiation.
Reported-by: Philip Langdale <philipl@overt.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Philip Langdale <philipl@overt.org> Tested-by: Philip Langdale <philipl@overt.org> Tested-by: Manuel Presnitz <mail@mpy.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Since the chained quirks via chained_before flag is applied before the
depth check, it may lead to the endless recursive calls, when the
chain were set up incorrectly. Fix it by moving the depth check at
the beginning of the loop.
Fixes: 1f57825077dc ("ALSA: hda - Add chained_before flag to the fixup entry") Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Similar to the fix done for IPv4 in commit e5b1c6c6277d
("igmp: fix memory leak in igmpv3_del_delrec()"), we need to
make sure mca_tomb and mca_sources are not blindly overwritten.
Using swap() then a call to ip6_mc_clear_src() will take care
of the missing free.
Fixes: 1666d49e1d41 ("mld: do not remove mld souce list info when set link down") Fixes: 9c8bb163ae78 ("igmp, mld: Fix memory leak in igmpv3/mld_del_delrec()") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Francois reported that VMware balloon gets stuck after a balloon reset,
when the VMCI doorbell is removed. A similar error can occur when the
balloon driver is removed with the following splat:
The cause for the bug is that when the "delayed" doorbell is invoked, it
takes a reference on the doorbell entry and schedules work that is
supposed to run the appropriate code and drop the doorbell entry
reference. The code ignores the fact that if the work is already queued,
it will not be scheduled to run one more time. As a result one of the
references would not be dropped. When the code waits for the reference
to get to zero, during balloon reset or module removal, it gets stuck.
Fix it. Drop the reference if schedule_work() indicates that the work is
already queued.
Note that this bug got more apparent (or apparent at all) due to
commit ce664331b248 ("vmw_balloon: VMCI_DOORBELL_SET does not check status").
In case of a disconnect an ongoing flush() has to be made fail.
Nevertheless we cannot be sure that any pending URB has already
finished, so although they will never succeed, they still must
not be touched.
The clean solution for this is to check for WDM_IN_USE
and WDM_DISCONNECTED in flush(). There is no point in ever
clearing WDM_IN_USE, as no further writes make sense.
The option named "auto_delink_en" is a bit misleading, as setting it to
false doesn't really disable auto-delink but let auto-delink be firmware
controlled.
Update the description to reflect the real usage of this parameter.
This patch fixes an issue that the following error is
possible to happen when ohci hardware causes an interruption
and the system is shutting down at the same time.
ohci_shutdown() disables all the interrupt and rh_state is set to
OHCI_RH_HALTED. In other hand, ohci_irq() is possible to enable
OHCI_INTR_SF and OHCI_INTR_MIE on ohci_irq(). Note that OHCI_INTR_SF
is possible to be set by start_ed_unlink() which is called:
ohci_irq()
-> process_done_list()
-> takeback_td()
-> start_ed_unlink()
So, ohci_irq() has the following condition, the issue happens by
&ohci->regs->intrenable = OHCI_INTR_MIE | OHCI_INTR_SF and
ohci->rh_state = OHCI_RH_HALTED:
/* interrupt for some other device? */
if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED))
return IRQ_NOTMINE;
To fix the issue, ohci_shutdown() holds the spin lock while disabling
the interruption and changing the rh_state flag to prevent reenable
the OHCI_INTR_MIE unexpectedly. Note that io_watchdog_func() also
calls the ohci_shutdown() and it already held the spin lock, so that
the patch makes a new function as _ohci_shutdown().
This patch is inspired by a Renesas R-Car Gen3 BSP patch
from Tho Vu.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/1566877910-6020-1-git-send-email-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16:
- Drop change in io_watchdog_func()
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The removal of the LDR initialization in the bigsmp_32 APIC code unearthed
a problem in setup_local_APIC().
The code checks unconditionally for a mismatch of the logical APIC id by
comparing the early APIC id which was initialized in get_smp_config() with
the actual LDR value in the APIC.
Due to the removal of the bogus LDR initialization the check now can
trigger on bigsmp_32 APIC systems emitting a warning for every booting
CPU. This is of course a false positive because the APIC is not using
logical destination mode.
Restrict the check and the possibly resulting fixup to systems which are
actually using the APIC in logical destination mode.
[ tglx: Massaged changelog and added Cc stable ]
Fixes: bae3a8d3308 ("x86/apic: Do not initialize LDR and DFR for bigsmp") Signed-off-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/666d8f91-b5a8-1afd-7add-821e72a35f03@suse.com
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Legacy apic init uses bigsmp for smp systems with 8 and more CPUs. The
bigsmp APIC implementation uses physical destination mode, but it
nevertheless initializes LDR and DFR. The LDR even ends up incorrectly with
multiple bit being set.
This does not cause a functional problem because LDR and DFR are ignored
when physical destination mode is active, but it triggered a problem on a
32-bit KVM guest which jumps into a kdump kernel.
The multiple bits set unearthed a bug in the KVM APIC implementation. The
code which creates the logical destination map for VCPUs ignores the
disabled state of the APIC and ends up overwriting an existing valid entry
and as a result, APIC calibration hangs in the guest during kdump
initialization.
Remove the bogus LDR/DFR initialization.
This is not intended to work around the KVM APIC bug. The LDR/DFR
ininitalization is wrong on its own.
The issue goes back into the pre git history. The fixes tag is the commit
in the bitkeeper import which introduced bigsmp support in 2003.
Fixes: db7b9e9f26b8 ("[PATCH] Clustered APIC setup for >8 CPU systems") Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Bandan Das <bsd@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190826101513.5080-2-bsd@redhat.com Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
32-bit processes running on a 64-bit kernel are not always detected
correctly, causing the process to crash when uretprobes are installed.
The reason for the crash is that in_ia32_syscall() is used to determine the
process's mode, which only works correctly when called from a syscall.
In the case of uretprobes, however, the function is called from a exception
and always returns 'false' on a 64-bit kernel. In consequence this leads to
corruption of the process's return address.
Fix this by using user_64bit_mode() instead of in_ia32_syscall(), which
is correct in any situation.
[ tglx: Add a comment and the following historical info ]
This should have been detected by the rename which happened in commit
abfb9498ee13 ("x86/entry: Rename is_{ia32,x32}_task() to in_{ia32,x32}_syscall()")
which states in the changelog:
The is_ia32_task()/is_x32_task() function names are a big misnomer: they
suggests that the compat-ness of a system call is a task property, which
is not true, the compatness of a system call purely depends on how it
was invoked through the system call layer.
.....
and then it went and blindly renamed every call site.
Sadly enough this was already mentioned here:
8faaed1b9f50 ("uprobes/x86: Introduce sizeof_long(), cleanup adjust_ret_addr() and
arch_uretprobe_hijack_return_addr()")
where the changelog says:
TODO: is_ia32_task() is not what we actually want, TS_COMPAT does
not necessarily mean 32bit. Fortunately syscall-like insns can't be
probed so it actually works, but it would be better to rename and
use is_ia32_frame().
and goes all the way back to:
0326f5a94dde ("uprobes/core: Handle breakpoint and singlestep exceptions")
Oh well. 7+ years until someone actually tried a uretprobe on a 32bit
process on a 64bit kernel....
Fixes: 0326f5a94dde ("uprobes/core: Handle breakpoint and singlestep exceptions") Signed-off-by: Sebastian Mayr <me@sam.st> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Dmitry Safonov <dsafonov@virtuozzo.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Link: https://lkml.kernel.org/r/20190728152617.7308-1-me@sam.st
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In its current form, user_64bit_mode() can only be used when CONFIG_X86_64
is selected. This implies that code built with CONFIG_X86_64=n cannot use
it. If a piece of code needs to be built for both CONFIG_X86_64=y and
CONFIG_X86_64=n and wants to use this function, it needs to wrap it in
an #ifdef/#endif; potentially, in multiple places.
This can be easily avoided with a single #ifdef/#endif pair within
user_64bit_mode() itself.
Suggested-by: Borislav Petkov <bp@suse.de> Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Borislav Petkov <bp@suse.de> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: ricardo.neri@intel.com Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Huang Rui <ray.huang@amd.com> Cc: Qiaowei Ren <qiaowei.ren@intel.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: "Ravi V. Shankar" <ravi.v.shankar@intel.com> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Brian Gerst <brgerst@gmail.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Colin Ian King <colin.king@canonical.com> Cc: Chen Yucong <slaoub@gmail.com> Cc: Adam Buchbinder <adam.buchbinder@gmail.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Thomas Garnier <thgarnie@google.com> Link: https://lkml.kernel.org/r/1509135945-13762-4-git-send-email-ricardo.neri-calderon@linux.intel.com
[bwh: Backported to 3.16 as dependency of "uprobes/x86: Fix detection of
32-bit user mode":
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The input pool of a client might be deleted via the resize ioctl, the
the access to it should be covered by the proper locks. Currently the
only missing place is the call in snd_seq_ioctl_get_client_pool(), and
this patch papers over it.
Reported-by: syzbot+4a75454b9ca2777f35c7@syzkaller.appspotmail.com Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Multiple batadv_ogm_packet can be stored in an skbuff. The functions
batadv_iv_ogm_send_to_if()/batadv_iv_ogm_receive() use
batadv_iv_ogm_aggr_packet() to check if there is another additional
batadv_ogm_packet in the skb or not before they continue processing the
packet.
The length for such an OGM is BATADV_OGM_HLEN +
batadv_ogm_packet->tvlv_len. The check must first check that at least
BATADV_OGM_HLEN bytes are available before it accesses tvlv_len (which is
part of the header. Otherwise it might try read outside of the currently
available skbuff to get the content of tvlv_len.
Fixes: ef26157747d4 ("batman-adv: tvlv - basic infrastructure") Reported-by: syzbot+355cab184197dbbfa384@syzkaller.appspotmail.com Signed-off-by: Sven Eckelmann <sven@narfation.org> Acked-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[bwh: Backported to 3.16:
- Drop kernel-doc change
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Use 'lea' instead of 'add' when adjusting %rsp in CALL_NOSPEC so as to
avoid clobbering flags.
KVM's emulator makes indirect calls into a jump table of sorts, where
the destination of the CALL_NOSPEC is a small blob of code that performs
fast emulation by executing the target instruction with fixed operands.
adcb_al_dl:
0x000339f8 <+0>: adc %dl,%al
0x000339fa <+2>: ret
A major motiviation for doing fast emulation is to leverage the CPU to
handle consumption and manipulation of arithmetic flags, i.e. RFLAGS is
both an input and output to the target of CALL_NOSPEC. Clobbering flags
results in all sorts of incorrect emulation, e.g. Jcc instructions often
take the wrong path. Sans the nops...
ctxt->eflags = (ctxt->eflags & ~EFLAGS_MASK) | (flags & EFLAGS_MASK);
0x000359a8 <+136>: mov -0x10(%ebp),%eax
0x000359ab <+139>: and $0x8d5,%edi
0x000359b4 <+148>: and $0xfffff72a,%eax
0x000359b9 <+153>: or %eax,%edi
0x000359bd <+157>: mov %edi,0x4(%ebx)
For the most part this has gone unnoticed as emulation of guest code
that can trigger fast emulation is effectively limited to MMIO when
running on modern hardware, and MMIO is rarely, if ever, accessed by
instructions that affect or consume flags.
Breakage is almost instantaneous when running with unrestricted guest
disabled, in which case KVM must emulate all instructions when the guest
has invalid state, e.g. when the guest is in Big Real Mode during early
BIOS.
Fixes: 776b043848fd2 ("x86/retpoline: Add initial retpoline support") Fixes: 1a29b5b7f347a ("KVM: x86: Make indirect calls in emulator speculation safe") Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20190822211122.27579-1-sean.j.christopherson@intel.com Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If the sector number is too high, dm_table_find_target() should return a
pointer to a zeroed dm_target structure (the caller should test it with
dm_target_is_valid).
However, for some table sizes, the code in dm_table_find_target() that
performs btree lookup will access out of bound memory structures.
Fix this bug by testing the sector number at the beginning of
dm_table_find_target(). Also, add an "inline" keyword to the function
dm_table_get_size() because this is a hot path.
Fixes: 512875bd9661 ("dm: table detect io beyond device") Reported-by: Zhang Tao <kontais@zoho.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In commit 6096d91af0b6 ("dm space map metadata: fix occasional leak
of a metadata block on resize"), we refactor the commit logic to a new
function 'apply_bops'. But when that logic was replaced in out() the
return value was not stored. This may lead out() returning a wrong
value to the caller.
Fixes: 6096d91af0b6 ("dm space map metadata: fix occasional leak of a metadata block on resize") Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When btree_split_beneath() splits a node to two new children, it will
allocate two blocks: left and right. If right block's allocation
failed, the left block will be unlocked and marked dirty. If this
happened, the left block'ss content is zero, because it wasn't
initialized with the btree struct before the attempot to allocate the
right block. Upon return, when flushing the left block to disk, the
validator will fail when check this block. Then a BUG_ON is raised.
Fix this by completely initializing the left block before allocating and
initializing the right block.
Fixes: 4dcb8b57df359 ("dm btree: fix leak of bufio-backed block in btree_split_beneath error path") Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This reverts commit 96cce12ff6e0 ("cfg80211: fix processing world
regdomain when non modular").
Re-triggering a reg_process_hint with the last request on all events,
can make the regulatory domain fail in case of multiple WiFi modules. On
slower boards (espacially with mdev), enumeration of the WiFi modules
can end up in an intersected regulatory domain, and user cannot set it
with 'iw reg set' anymore.
This is happening, because:
- 1st module enumerates, queues up a regulatory request
- request gets processed by __reg_process_hint_driver():
- checks if previous was set by CORE -> yes
- checks if regulator domain changed -> yes, from '00' to e.g. 'US'
-> sends request to the 'crda'
- 2nd module enumerates, queues up a regulator request (which triggers
the reg_todo() work)
- reg_todo() -> reg_process_pending_hints() sees, that the last request
is not processed yet, so it tries to process it again.
__reg_process_hint driver() will run again, and:
- checks if the last request's initiator was the core -> no, it was
the driver (1st WiFi module)
- checks, if the previous initiator was the driver -> yes
- checks if the regulator domain changed -> yes, it was '00' (set by
core, and crda call did not return yet), and should be changed to 'US'
------> __reg_process_hint_driver calls an intersect
Besides, the reg_process_hint call with the last request is meaningless
since the crda call has a timeout work. If that timeout expires, the
first module's request will lost.
Fixes: 96cce12ff6e0 ("cfg80211: fix processing world regdomain when non modular") Signed-off-by: Robert Hodaszi <robert.hodaszi@digi.com> Link: https://lore.kernel.org/r/20190614131600.GA13897@a1-hr Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 69e3c75f4d54 ("net: TX_RING and packet mmap") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
On Motorola Mapphone devices such as Droid 4 there are five USB ports
that do not use the same layout as Gobi 1K/2K/etc devices listed in
qcserial.c. So we should use qcaux.c or option.c as noted by
Dan Williams <dan.j.williams@intel.com>.
As the Motorola USB serial ports have an interrupt endpoint as shown
with lsusb -v, we should use option.c instead of qcaux.c as pointed out
by Johan Hovold <johan@kernel.org>.
The ff/ff/ff interfaces seem to always be UARTs on Motorola devices.
For the other interfaces, class 0x0a (CDC Data) should not in general
be added as they are typically part of a multi-interface function as
noted earlier by Bjørn Mork <bjorn@mork.no>.
However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a
class is only used for flashing the modem firmware, and there are no
other interfaces. So I've added that too with more details below as it
works just fine.
The ttyUSB ports on Droid 4 are:
ttyUSB0 DIAG, CQDM-capable
ttyUSB1 MUX or NMEA, no response
ttyUSB2 MUX or NMEA, no response
ttyUSB3 TCMD
ttyUSB4 AT-capable
The ttyUSB0 is detected as QCDM capable by ModemManager. I think
it's only used for debugging with ModemManager --debug for sending
custom AT commands though. ModemManager already can manage data
connection using the USB QMI ports that are already handled by the
qmi_wwan.c driver.
To enable the MUX or NMEA ports, it seems that something needs to be
done additionally to enable them, maybe via the DIAG or TCMD port.
It might be just a NVRAM setting somewhere, but I have no idea what
NVRAM settings may need changing for that.
The TCMD port seems to be a Motorola custom protocol for testing
the modem and to configure it's NVRAM and seems to work just fine
based on a quick test with a minimal tcmdrw tool I wrote.
The voice modem AT-capable port seems to provide only partial
support, and no PM support compared to the TS 27.010 based UART
wired directly to the modem.
The UARTs added with this change are the same product IDs as the
Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't
have any mdm9600 based devices, so I have only tested these on
mdm6600 based droid 4.
Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android
Linux kernel driver moto_flashqsc.c just seems to change the
port->bulk_out_size to 8K from the default. And is only used for
flashing the modem firmware it seems.
I've verified that flashing the modem with signed firmware works just
fine with the option driver after manually toggling the GPIO pins, so
I've added droid 4 modem flashing mode to the option driver. I've not
added the other devices listed in moto_flashqsc.c in case they really
need different port->bulk_out_size. Those can be added as they get
tested to work for flashing the modem.
After this patch the output of /sys/kernel/debug/usb/devices has
the following for normal 22b8:2a70 mode including the related qmi_wwan
interfaces:
Cc: Bjørn Mork <bjorn@mork.no> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Lars Melin <larsm17@gmail.com> Cc: Marcel Partap <mpartap@gmx.net> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Michael Scott <hashcode0f@gmail.com> Cc: NeKit <nekit1000@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Tested-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Change ct id hash calculation to only use invariants.
Currently the ct id hash calculation is based on some fields that can
change in the lifetime on a conntrack entry in some corner cases. The
current hash uses the whole tuple which contains an hlist pointer which
will change when the conntrack is placed on the dying list resulting in
a ct id change.
This patch also removes the reply-side tuple and extension pointer from
the hash calculation so that the ct id will will not change from
initialization until confirmation.
Fixes: 3c79107631db1f7 ("netfilter: ctnetlink: don't use conntrack/expect object addresses as id") Signed-off-by: Dirk Morris <dmorris@metaloft.com> Acked-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The syzbot fuzzer has found two (!) races in the USB character device
registration and deregistration routines. This patch fixes the races.
The first race results from the fact that usb_deregister_dev() sets
usb_minors[intf->minor] to NULL before calling device_destroy() on the
class device. This leaves a window during which another thread can
allocate the same minor number but will encounter a duplicate name
error when it tries to register its own class device. A typical error
message in the system log would look like:
The patch fixes this race by destroying the class device first.
The second race is in usb_register_dev(). When that routine runs, it
first allocates a minor number, then drops minor_rwsem, and then
creates the class device. If the device creation fails, the minor
number is deallocated and the whole routine returns an error. But
during the time while minor_rwsem was dropped, there is a window in
which the minor number is allocated and so another thread can
successfully open the device file. Typically this results in
use-after-free errors or invalid accesses when the other thread closes
its open file reference, because the kernel then tries to release
resources that were already deallocated when usb_register_dev()
failed. The patch fixes this race by keeping minor_rwsem locked
throughout the entire routine.
`dt3k_ns_to_timer()` determines the prescaler and divisor to use to
produce a desired timing period. It is influenced by a rounding mode
and can round the divisor up, down, or to the nearest value. However,
the code for rounding up currently does the same as rounding down! Fix
ir by using the `DIV_ROUND_UP()` macro to calculate the divisor when
rounding up.
Also, change the types of the `divider`, `base` and `prescale` variables
from `int` to `unsigned int` to avoid mixing signed and unsigned types
in the calculations.
Also fix a typo in a nearby comment: "improvment" => "improvement".
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Link: https://lore.kernel.org/r/20190812120814.21188-1-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
(`divider`, `base` and `prescale` are type `int`, `timer_base` and
`*nanosec` are type `unsigned int`. The value of `timer_base` will be
either 50 or 100.)
The main reason for the overflow is that the calculation for `base` is
completely wrong. It should be:
base = timer_base * (prescale + 1);
which matches an earlier instance of this calculation in the same
function.
Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Link: https://lore.kernel.org/r/20190812111517.26803-1-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
drivers/net/ethernet/toshiba/tc35815.c:1507:30: warning: use of logical
'&&' with constant operand [-Wconstant-logical-operand]
if (!HAVE_DMA_RXALIGN(lp) && NET_IP_ALIGN)
^ ~~~~~~~~~~~~
drivers/net/ethernet/toshiba/tc35815.c:1507:30: note: use '&' for a
bitwise operation
if (!HAVE_DMA_RXALIGN(lp) && NET_IP_ALIGN)
^~
&
drivers/net/ethernet/toshiba/tc35815.c:1507:30: note: remove constant to
silence this warning
if (!HAVE_DMA_RXALIGN(lp) && NET_IP_ALIGN)
~^~~~~~~~~~~~~~~
1 warning generated.
Explicitly check that NET_IP_ALIGN is not zero, which matches how this
is checked in other parts of the tree. Because NET_IP_ALIGN is a build
time constant, this check will be constant folded away during
optimization.
Fixes: 82a9928db560 ("tc35815: Enable StripCRC feature") Link: https://github.com/ClangBuiltLinux/linux/issues/608 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In snd_hda_parse_generic_codec(), 'spec' is allocated through kzalloc().
Then, the pin widgets in 'codec' are parsed. However, if the parsing
process fails, 'spec' is not deallocated, leading to a memory leak.
To fix the above issue, free 'spec' before returning the error.
Fixes: 352f7f914ebb ("ALSA: hda - Merge Realtek parser code to generic parser") Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In iso_packets_buffer_init(), 'b->packets' is allocated through
kmalloc_array(). Then, the aligned packet size is checked. If it is
larger than PAGE_SIZE, -EINVAL will be returned to indicate the error.
However, the allocated 'b->packets' is not deallocated on this path,
leading to a memory leak.
To fix the above issue, free 'b->packets' before returning the error code.
In sound_insert_unit(), the controlling structure 's' is allocated through
kmalloc(). Then it is added to the sound driver list by invoking
__sound_insert_unit(). Later on, if __register_chrdev() fails, 's' is
removed from the list through __sound_remove_unit(). If 'index' is not less
than 0, -EBUSY is returned to indicate the error. However, 's' is not
deallocated on this execution path, leading to a memory leak bug.
To fix the above issue, free 's' before -EBUSY is returned.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We had a report of a server which did not do a DFS referral
because the session setup Capabilities field was set to 0
(unlike negotiate protocol where we set CAP_DFS). Better to
send it session setup in the capabilities as well (this also
more closely matches Windows client behavior).
Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently we skip SMB2_TREE_CONNECT command when checking during
reconnect because Tree Connect happens when establishing
an SMB session. For SMB 3.0 protocol version the code also calls
validate negotiate which results in SMB2_IOCL command being sent
over the wire. This may deadlock on trying to acquire a mutex when
checking for reconnect. Fix this by skipping SMB2_IOCL command
when doing the reconnect check.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
BUG: KASAN: use-after-free in usb_free_coherent+0x79/0x80
drivers/usb/core/usb.c:928
Read of size 8 at addr ffff8881b18599c8 by task syz-executor.4/16007
Memory state around the buggy address: ffff8881b1859880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881b1859900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
> ffff8881b1859980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881b1859a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881b1859a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
A quick look at the yurex_delete() shows that we drop the reference
to the usb_device before releasing any buffers associated with the
device. Delay the reference drop until we have finished the cleanup.
projects / thirdparty / kernel / stable.git / log
