In a randconfig with CONFIG_SERIAL_CPM=m and
CONFIG_PPC_EARLY_DEBUG_CPM=y, there is a build error:
ERROR: modpost: "udbg_putc" [drivers/tty/serial/cpm_uart/cpm_uart.ko] undefined!
Prevent the build error by allowing PPC_EARLY_DEBUG_CPM only when
SERIAL_CPM=y.
Fixes: c374e00e17f1 ("[POWERPC] Add early debug console for CPM serial ports.") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230701054714.30512-1-rdunlap@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Sec proxy/message manager data buffer is 60 bytes with the last of the
registers indicating transmission completion. This however poses a bit
of a challenge.
The backing memory for sec_proxy / message manager is regular memory,
and all sec proxy does is to trigger a burst of all 60 bytes of data
over to the target thread backing ring accelerator. It doesn't do a
memory scrub when it moves data out in the burst. When we transmit
multiple messages, remnants of previous message is also transmitted
which results in some random data being set in TISCI fields of
messages that have been expanded forward.
The entire concept of backward compatibility hinges on the fact that
the unused message fields remain 0x0 allowing for 0x0 value to be
specially considered when backward compatibility of message extension
is done.
So, instead of just writing the completion register, we continue
to fill the message buffer up with 0x0 (note: for partial message
involving completion, we already do this).
This allows us to scale and introduce ABI changes back also work with
other boot stages that may have left data in the internal memory.
While at this, be consistent and explicit with the data_reg pointer
increment.
If neither a "hif_mspi" nor "mspi" resource is present, the driver will
just early exit in probe but still return success. Apart from not doing
anything meaningful, this would then also lead to a null pointer access
on removal, as platform_get_drvdata() would return NULL, which it would
then try to dereference when trying to unregister the spi master.
Fix this by unconditionally calling devm_ioremap_resource(), as it can
handle a NULL res and will then return a viable ERR_PTR() if we get one.
The "return 0;" was previously a "goto qspi_resource_err;" where then
ret was returned, but since ret was still initialized to 0 at this place
this was a valid conversion in 63c5395bb7a9 ("spi: bcm-qspi: Fix
use-after-free on unbind"). The issue was not introduced by this commit,
only made more obvious.
Fixes: fa236a7ef240 ("spi: bcm-qspi: Add Broadcom MSPI driver") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Kamal Dasu <kamal.dasu@broadcom.com> Link: https://lore.kernel.org/r/20230629134306.95823-1-jonas.gorski@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As &net->sctp.addr_wq_lock is also acquired by the timer
sctp_addr_wq_timeout_handler() in protocal.c, the same lock acquisition
at sctp_auto_asconf_init() seems should disable irq since it is called
from sctp_accept() under process context.
This flaw was found using an experimental static analysis tool we are
developing for irq-related deadlock.
The tentative patch fix the potential deadlock by spin_lock_bh().
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com> Fixes: 34e5b0118685 ("sctp: delay auto_asconf init until binding the first addr") Acked-by: Xin Long <lucien.xin@gmail.com> Link: https://lore.kernel.org/r/20230627120340.19432-1-dg573847474@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The fuel gauge in the RT5033 PMIC (rt5033-battery) has its own I2C bus
and interrupt lines. Therefore, it is not part of the MFD device
and needs to be specified separately in the device tree.
Fixes: 0b271258544b ("mfd: rt5033: Add Richtek RT5033 driver core.") Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Jakob Hauser <jahau@rocketmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/6a8a19bc67b5be3732882e8131ad2ffcb546ac03.1684182964.git.jahau@rocketmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Kernel documentation has to be synchronized with a code, otherwise
the validator is not happy:
Function parameter or member 'usb_bits' not described in 'extcon_cable'
Function parameter or member 'chg_bits' not described in 'extcon_cable'
Function parameter or member 'jack_bits' not described in 'extcon_cable'
Function parameter or member 'disp_bits' not described in 'extcon_cable'
Describe the fields added in the past.
Fixes: ceaa98f442cf ("extcon: Add the support for the capability of each property") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Kernel documentation has to be synchronized with a code, otherwise
the validator is not happy:
Function parameter or member 'usb_propval' not described in 'extcon_cable'
Function parameter or member 'chg_propval' not described in 'extcon_cable'
Function parameter or member 'jack_propval' not described in 'extcon_cable'
Function parameter or member 'disp_propval' not described in 'extcon_cable'
Describe the fields added in the past.
Fixes: 067c1652e7a7 ("extcon: Add the support for extcon property according to extcon type") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The previous commit ebad8e731c1c ("media: usb: siano: Fix use after
free bugs caused by do_submit_urb") adds cancel_work_sync() in
smsusb_stop_streaming(). But smsusb_stop_streaming() may be called,
even if the work_struct surb->wq has not been initialized. As a result,
the warning will occur. One of the processes that could lead to warning
is shown below:
smsusb_probe()
smsusb_init_device()
if (!dev->in_ep || !dev->out_ep || align < 0) {
smsusb_term_device(intf);
smsusb_stop_streaming()
cancel_work_sync(&dev->surbs[i].wq);
__cancel_work_timer()
__flush_work()
if (WARN_ON(!work->func)) // work->func is null
VIDIOC_ENUMINPUT documentation describes the tuner field of
struct v4l2_input as index:
Documentation/userspace-api/media/v4l/vidioc-enuminput.rst
"
* - __u32
- ``tuner``
- Capture devices can have zero or more tuners (RF demodulators).
When the ``type`` is set to ``V4L2_INPUT_TYPE_TUNER`` this is an
RF connector and this field identifies the tuner. It corresponds
to struct :c:type:`v4l2_tuner` field ``index``. For
details on tuners see :ref:`tuner`.
"
Drivers I could find also use the 'tuner' field as an index, e.g.:
drivers/media/pci/bt8xx/bttv-driver.c bttv_enum_input()
drivers/media/usb/go7007/go7007-v4l2.c vidioc_enum_input()
However, the UAPI comment claims this field is 'enum v4l2_tuner_type':
include/uapi/linux/videodev2.h
This field being 'enum v4l2_tuner_type' is unlikely as it seems to be
never used that way in drivers, and documentation confirms it. It seem
this comment got in accidentally in the commit which this patch fixes.
Fix the UAPI comment to stop confusion.
This was pointed out by Dmitry while reviewing VIDIOC_ENUMINPUT
support for strace.
Fixes: 6016af82eafc ("[media] v4l2: use __u32 rather than enums in ioctl() structs") Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Addresses the following warning when building j2_defconfig:
arch/sh/kernel/cpu/sh2/probe.c: In function 'scan_cache':
arch/sh/kernel/cpu/sh2/probe.c:24:16: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
24 | j2_ccr_base = (u32 __iomem *)of_flat_dt_translate_address(node);
|
Fixes: 5a846abad07f ("sh: add support for J-Core J2 processor") Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Rob Landley <rob@landley.net> Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Link: https://lore.kernel.org/r/20230503125746.331835-1-glaubitz@physik.fu-berlin.de Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Amiga partition parser module uses signed int for partition sector
address and count, which will overflow for disks larger than 1 TB.
Use u64 as type for sector address and size to allow using disks up to
2 TB without LBD support, and disks larger than 2 TB with LBD. The RBD
format allows to specify disk sizes up to 2^128 bytes (though native
OS limitations reduce this somewhat, to max 2^68 bytes), so check for
u64 overflow carefully to protect against overflowing sector_t.
This bug was reported originally in 2012, and the fix was created by
the RDB author, Joanne Dow <jdow@earthlink.net>. A patch had been
discussed and reviewed on linux-m68k at that time but never officially
submitted (now resubmitted as patch 1 of this series).
Patch 3 (this series) adds additional error checking and warning
messages. One of the error checks now makes use of the previously
unused rdb_CylBlocks field, which causes a 'sparse' warning
(cast to restricted __be32).
Annotate all 32 bit fields in affs_hardblocks.h as __be32, as the
on-disk format of RDB and partition blocks is always big endian.
The new LARA-R6 product variant identified by the "01B" string can be
configured (by AT interface) in three different USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1311) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1312) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1313) with 4 serial
interface and 1 CDC-ECM virtual network interface
The first 4 interfaces of all the 3 USB configurations (default, RmNet,
CDC-ECM) are the same.
In default mode LARA-R6 01B exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
In RmNet mode LARA-R6 01B exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
If 4: RMNET interface
In CDC-ECM mode LARA-R6 01B exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
If 4: CDC-ECM interface
(You need to use GNU linker instead of LLD to reproduce it.)
Fix the code to make modpost show the correct symbol name.
I imported (with adjustment) sign_extend32() from include/linux/bitops.h.
The '+8' is the compensation for pc-relative instruction. It is
documented in "ELF for the Arm Architecture" [1].
"If the relocation is pc-relative then compensation for the PC bias
(the PC value is 8 bytes ahead of the executing instruction in Arm
state and 4 bytes in Thumb state) must be encoded in the relocation
by the object producer."
The reference from 'get_bar' to 'foo' seems wrong.
I have no solution for this because it is true in assembly level.
In the following output, relocation at 0x1c is no longer associated
with 'bar'. The two relocation entries point to the same symbol, and
the offset to 'bar' is encoded in the instruction 'r0, [r3, #4]'.
Relocation section '.rel.text' at offset 0x244 contains 2 entries:
Offset Info Type Sym.Value Sym. Name 0000000c00000c02 R_ARM_ABS32 00000000 .init.data 0000001c00000c02 R_ARM_ABS32 00000000 .init.data
When find_elf_symbol() gets into a situation where relsym->st_name is
zero, there is no guarantee to get the symbol name as written in C.
I am keeping the current logic because it is useful in many architectures,
but the symbol name is not always correct depending on the optimization.
I left some comments in find_tosym().
Fixes: 56a974fa2d59 ("kbuild: make better section mismatch reports on arm") Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix build warnings when DEBUG_FS is not enabled by using an empty
do-while loop instead of a value:
In file included from ../drivers/crypto/nx/nx.c:27:
../drivers/crypto/nx/nx.c: In function 'nx_register_algs':
../drivers/crypto/nx/nx.h:173:33: warning: statement with no effect [-Wunused-value]
173 | #define NX_DEBUGFS_INIT(drv) (0)
../drivers/crypto/nx/nx.c:573:9: note: in expansion of macro 'NX_DEBUGFS_INIT'
573 | NX_DEBUGFS_INIT(&nx_driver);
../drivers/crypto/nx/nx.c: In function 'nx_remove':
../drivers/crypto/nx/nx.h:174:33: warning: statement with no effect [-Wunused-value]
174 | #define NX_DEBUGFS_FINI(drv) (0)
../drivers/crypto/nx/nx.c:793:17: note: in expansion of macro 'NX_DEBUGFS_FINI'
793 | NX_DEBUGFS_FINI(&nx_driver);
Also, there is no need to build nx_debugfs.o when DEBUG_FS is not
enabled, so change the Makefile to accommodate that.
Fixes: ae0222b7289d ("powerpc/crypto: nx driver code supporting nx encryption") Fixes: aef7b31c8833 ("powerpc/crypto: Build files for the nx device driver") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Breno Leitão <leitao@debian.org> Cc: Nayna Jain <nayna@linux.ibm.com> Cc: Paulo Flabiano Smorigo <pfsmorigo@gmail.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: "David S. Miller" <davem@davemloft.net> Cc: linux-crypto@vger.kernel.org Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
devm_kasprintf() returns a pointer to dynamically allocated memory.
Pointer could be NULL in case allocation fails. Check pointer validity.
Identified with coccinelle (kmerr.cocci script).
Fixes: 776180848b57 ("pinctrl: introduce driver for Atmel PIO4 controller")
Depends-on: 1c4e5c470a56 ("pinctrl: at91: use devm_kasprintf() to avoid potential leaks")
Depends-on: 5a8f9cf269e8 ("pinctrl: at91-pio4: use proper format specifier for unsigned int") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20230615105333.585304-4-claudiu.beznea@microchip.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The die_get_varname() returns "(unknown_type)" string if it failed to
find a type for the variable. But it had a space before the opening
parenthesis and it made the closing parenthesis cut off due to the
off-by-one in the string length (14).
Signed-off-by: Namhyung Kim <namhyung@kernel.org> Fixes: 88fd633cdfa19060 ("perf probe: No need to use formatting strbuf method") Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20230612234102.3909116-1-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a pci_clear_master() stub when CONFIG_PCI is not set so drivers that
support both PCI and platform devices don't need #ifdefs or extra Kconfig
symbols for the PCI parts.
[bhelgaas: commit log] Fixes: 6a479079c072 ("PCI: Add pci_clear_master() as opposite of pci_set_master()") Link: https://lore.kernel.org/r/20230531102744.2354313-1-suijingfeng@loongson.cn Signed-off-by: Sui Jingfeng <suijingfeng@loongson.cn> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds error checking to tw_probe() to handle initialization
failure. If tw_reset_sequence() function returns a non-zero value, the
function will return -EINVAL to indicate initialization failure.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Yuchen Yang <u202114568@hust.edu.cn> Link: https://lore.kernel.org/r/20230505141259.7730-1-u202114568@hust.edu.cn Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function rv740_get_decoded_reference_divider() may return 0 due to
unpredictable reference divider value calculated in
radeon_atom_get_clock_dividers(). This will lead to
division-by-zero error once that value is used as a divider
in calculating 'clk_s'.
While unlikely, this issue should nonetheless be prevented so add a
sanity check for such cases by testing 'decoded_ref' value against 0.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
v2: minor coding style fixes (Alex)
In practice this should actually happen as the vbios should be
properly populated.
Fixes: 66229b200598 ("drm/radeon/kms: add dpm support for rv7xx (v4)") Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix build errors in soc/fsl/qe/usb.c when QUICC_ENGINE is not set.
This happens when PPC_EP88XC is set, which selects CPM1 & CPM.
When CPM is set, USB_FSL_QE can be set without QUICC_ENGINE
being set. When USB_FSL_QE is set, QE_USB deafults to y, which
causes build errors when QUICC_ENGINE is not set. Making
QE_USB depend on QUICC_ENGINE prevents QE_USB from defaulting to y.
Fixes these build errors:
drivers/soc/fsl/qe/usb.o: in function `qe_usb_clock_set':
usb.c:(.text+0x1e): undefined reference to `qe_immr'
powerpc-linux-ld: usb.c:(.text+0x2a): undefined reference to `qe_immr'
powerpc-linux-ld: usb.c:(.text+0xbc): undefined reference to `qe_setbrg'
powerpc-linux-ld: usb.c:(.text+0xca): undefined reference to `cmxgcr_lock'
powerpc-linux-ld: usb.c:(.text+0xce): undefined reference to `cmxgcr_lock'
Fixes: 5e41486c408e ("powerpc/QE: add support for QE USB clocks routing") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/all/202301101500.pillNv6R-lkp@intel.com/ Suggested-by: Michael Ellerman <mpe@ellerman.id.au> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Leo Li <leoyang.li@nxp.com> Cc: Masahiro Yamada <masahiroy@kernel.org> Cc: Nicolas Schier <nicolas@fjasle.eu> Cc: Qiang Zhao <qiang.zhao@nxp.com> Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org> Cc: linux-arm-kernel@lists.infradead.org Cc: Kumar Gala <galak@kernel.crashing.org> Acked-by: Nicolas Schier <nicolas@jasle.eu> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to ES8316 datasheet, the register at address 0x2B, which is
related to the above mixer control, contains by default the value 0xB0.
Considering the corresponding ALC target bits (ALCLVL) are 7:4, the
control is initialized with 11, which is one step above the maximum
value allowed by the driver:
The tests performed using the VU meter feature (--vumeter=TYPE) of
arecord/aplay confirm the specs are correct and there is no measured
gain if the 1011-1111 range would have been mapped to 0 dB:
dB gain | VU meter %
--------+-----------
-6.0 | 30-31
-4.5 | 35-36
-3.0 | 42-43
-1.5 | 50-51
0.0 | 50-51
Increment the max value allowed for ALC Capture Target Volume control,
so that it matches the hardware default. Additionally, update the
related TLV to prevent an artificial extension of the dB gain range.
ep93xx_clocksource_read() is only called from the file it is declared in,
while ep93xx_timer_init() is declared in a header that is not included here.
arch/arm/mach-ep93xx/timer-ep93xx.c:120:13: error: no previous prototype for 'ep93xx_timer_init'
arch/arm/mach-ep93xx/timer-ep93xx.c:63:5: error: no previous prototype for 'ep93xx_clocksource_read'
The previous setting was related to the overall dimension and not to the
active display area.
In the "PHYSICAL SPECIFICATIONS" section, the datasheet shows the
following parameters:
----------------------------------------------------------
| Item | Specifications | unit |
----------------------------------------------------------
| Display area | 98.7 (W) x 57.5 (H) | mm |
----------------------------------------------------------
| Overall dimension | 105.5(W) x 67.2(H) x 4.96(D) | mm |
----------------------------------------------------------
Fixes: 966fea78adf2 ("drm/panel: simple: Add support for Ampire AM-480272H3TMQW-T01H") Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
[narmstrong: fixed Fixes commit id length] Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230516085039.3797303-1-dario.binacchi@amarulasolutions.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no such property in the SPI controller binding documentation.
Also Linux driver doesn't look for it.
This fixes:
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: spi@18029200: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.yaml
Several calls to ci_dpm_fini() will attempt to free resources that
either have been freed before or haven't been allocated yet. This
may lead to undefined or dangerous behaviour.
For instance, if r600_parse_extended_power_table() fails, it might
call r600_free_extended_power_table() as will ci_dpm_fini() later
during error handling.
Fix this by only freeing pointers to objects previously allocated.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: cc8dbbb4f62a ("drm/radeon: add dpm support for CI dGPUs (v2)") Co-developed-by: Natalia Petrova <n.petrova@fintech.ru> Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reported a warning in __local_bh_enable_ip(). [0]
Commit 8d61f926d420 ("netlink: fix potential deadlock in
netlink_set_err()") converted read_lock(&nl_table_lock) to
read_lock_irqsave() in __netlink_diag_dump() to prevent a deadlock.
However, __netlink_diag_dump() calls sock_i_ino() that uses
read_lock_bh() and read_unlock_bh(). If CONFIG_TRACE_IRQFLAGS=y,
read_unlock_bh() finally enables IRQ even though it should stay
disabled until the following read_unlock_irqrestore().
Using read_lock() in sock_i_ino() would trigger a lockdep splat
in another place that was fixed in commit f064af1e500a ("net: fix
a lockdep splat"), so let's add __sock_i_ino() that would be safe
to use under BH disabled.
ct_sip_parse_numerical_param() returns only 0 or 1 now.
But process_register_request() and process_register_response() imply
checking for a negative value if parsing of a numerical header parameter
failed.
The invocation in nf_nat_sip() looks correct:
if (ct_sip_parse_numerical_param(...) > 0 &&
...) { ... }
Make the return value of the function ct_sip_parse_numerical_param()
a tristate to fix all the cases
a) return 1 if value is found; *val is set
b) return 0 if value is not found; *val is unchanged
c) return -1 on error; *val is undefined
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
The `shift` variable which indicates the offset in the string at which
to start matching the pattern is initialized to `bm->patlen - 1`, but it
is not reset when a new block is retrieved. This means the implemen-
tation may start looking at later and later positions in each successive
block and miss occurrences of the pattern at the beginning. E.g.,
consider a HTTP packet held in a non-linear skb, where the HTTP request
line occurs in the second block:
[... 52 bytes of packet headers ...]
GET /bmtest HTTP/1.1\r\nHost: www.example.com\r\n\r\n
and the pattern is "GET /bmtest".
Once the first block comprising the packet headers has been examined,
`shift` will be pointing to somewhere near the end of the block, and so
when the second block is examined the request line at the beginning will
be missed.
Reinitialize the variable for each new block.
Fixes: 8082e4ed0a61 ("[LIB]: Boyer-Moore extension for textsearch infrastructure strike #2") Link: https://bugzilla.netfilter.org/show_bug.cgi?id=1390 Signed-off-by: Jeremy Sowden <jeremy@azazel.net> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzkaller reported use-after-free in __gtp_encap_destroy(). [0]
It shows the same process freed sk and touched it illegally.
Commit e198987e7dd7 ("gtp: fix suspicious RCU usage") added lock_sock()
and release_sock() in __gtp_encap_destroy() to protect sk->sk_user_data,
but release_sock() is called after sock_put() releases the last refcnt.
[0]:
BUG: KASAN: slab-use-after-free in instrument_atomic_read_write include/linux/instrumented.h:96 [inline]
BUG: KASAN: slab-use-after-free in atomic_try_cmpxchg_acquire include/linux/atomic/atomic-instrumented.h:541 [inline]
BUG: KASAN: slab-use-after-free in queued_spin_lock include/asm-generic/qspinlock.h:111 [inline]
BUG: KASAN: slab-use-after-free in do_raw_spin_lock include/linux/spinlock.h:186 [inline]
BUG: KASAN: slab-use-after-free in __raw_spin_lock_bh include/linux/spinlock_api_smp.h:127 [inline]
BUG: KASAN: slab-use-after-free in _raw_spin_lock_bh+0x75/0xe0 kernel/locking/spinlock.c:178
Write of size 4 at addr ffff88800dbef398 by task syz-executor.2/2401
The buggy address belongs to the object at ffff88800dbef300
which belongs to the cache UDPv6 of size 1344
The buggy address is located 152 bytes inside of
freed 1344-byte region [ffff88800dbef300, ffff88800dbef840)
Memory state around the buggy address: ffff88800dbef280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88800dbef300: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff88800dbef380: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff88800dbef400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88800dbef480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
syz-executor.2/23011 just changed the state of lock: ffffffff8e1a7a58 (nl_table_lock){.+.?}-{2:2}, at: netlink_set_err+0x2e/0x3a0 net/netlink/af_netlink.c:1612
but this lock was taken by another, SOFTIRQ-safe lock in the past:
(&local->queue_stop_reason_lock){..-.}-{2:2}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
Since 'ieee80211_queue_delayed_work()' expects timeout in
jiffies and not milliseconds, 'msecs_to_jiffies()' should
be used in 'ath_restart_work()' and '__ath9k_flush()'.
Fixes: d63ffc45c5d3 ("ath9k: rename tx_complete_work to hw_check_work") Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230613134655.248728-1-dmantipov@yandex.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
On EDMA capable hardware, ath9k_txq_list_has_key() can enter infinite
loop if it is called while all txq_fifos have packets that use different
key that the one we are looking for. Fix it by exiting the loop if all
txq_fifos have been checked already.
Because this loop is called under spin_lock_bh() (see ath_txq_lock) it
causes the following rcu stall:
There are no other files referencing this function, apparently
it was left global to avoid an 'unused function' warning when
the only caller is left out. With a 'W=1' build, it causes
a 'missing prototype' warning though:
drivers/memstick/host/r592.c:47:13: error: no previous prototype for 'memstick_debug_get_tpc_name' [-Werror=missing-prototypes]
Annotate the function as 'static __maybe_unused' to avoid both
problems.
Patch series "kexec: enable kexec_crash_size to support two crash kernel
regions".
When crashkernel=X fails to reserve region under 4G, it will fall back to
reserve region above 4G and a region of the default size will also be
reserved under 4G. Unfortunately, /sys/kernel/kexec_crash_size only
supports one crash kernel region now, the user cannot sense the low memory
reserved by reading /sys/kernel/kexec_crash_size. Also, low memory cannot
be freed by writing this file.
For example:
resource_size(crashk_res) = 512M
resource_size(crashk_low_res) = 256M
The result of 'cat /sys/kernel/kexec_crash_size' is 512M, but it should be
768M. When we execute 'echo 0 > /sys/kernel/kexec_crash_size', the size
of crashk_res becomes 0 and resource_size(crashk_low_res) is still 256 MB,
which is incorrect.
Since crashk_res manages the memory with high address and crashk_low_res
manages the memory with low address, crashk_low_res is shrunken only when
all crashk_res is shrunken. And because when there is only one crash
kernel region, crashk_res is always used. Therefore, if all crashk_res is
shrunken and crashk_low_res still exists, swap them.
This patch (of 6):
If the value of parameter 'new_size' is in the semi-open and semi-closed
interval (crashk_res.end - KEXEC_CRASH_MEM_ALIGN + 1, crashk_res.end], the
calculation result of ram_res is:
The operation of insert_resource() fails, and ram_res is not added to
iomem_resource. As a result, the memory of the control block ram_res is
leaked.
In fact, on all architectures, the start address and size of crashk_res
are already aligned by KEXEC_CRASH_MEM_ALIGN. Therefore, we do not need
to round up crashk_res.start again. Instead, we should round up
'new_size' in advance.
Link: https://lkml.kernel.org/r/20230527123439.772-1-thunder.leizhen@huawei.com Link: https://lkml.kernel.org/r/20230527123439.772-2-thunder.leizhen@huawei.com Fixes: 6480e5a09237 ("kdump: add missing RAM resource in crash_shrink_memory()") Fixes: 06a7f711246b ("kexec: premit reduction of the reserved memory size") Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: Cong Wang <amwang@redhat.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, in the watchdog_overflow_callback() we first check to see if
the watchdog had been touched and _then_ we handle the workaround for
turbo mode. This order should be reversed.
Specifically, "touching" the hardlockup detector's watchdog should avoid
lockups being detected for one period that should be roughly the same
regardless of whether we're running turbo or not. That means that we
should do the extra accounting for turbo _before_ we look at (and clear)
the global indicating that we've been touched.
NOTE: this fix is made based on code inspection. I am not aware of any
reports where the old code would have generated false positives. That
being said, this order seems more correct and also makes it easier down
the line to share code with the "buddy" hardlockup detector.
Link: https://lkml.kernel.org/r/20230519101840.v5.2.I843b0d1de3e096ba111a179f3adb16d576bef5c7@changeid Fixes: 7edaeb6841df ("kernel/watchdog: Prevent false positives with turbo modes") Signed-off-by: Douglas Anderson <dianders@chromium.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Colin Cross <ccross@android.com> Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Guenter Roeck <groeck@chromium.org> Cc: Ian Rogers <irogers@google.com> Cc: Lecopzer Chen <lecopzer.chen@mediatek.com> Cc: Marc Zyngier <maz@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Masayoshi Mizuma <msys.mizuma@gmail.com> Cc: Matthias Kaehlcke <mka@chromium.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Pingfan Liu <kernelfans@gmail.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: "Ravi V. Shankar" <ravi.v.shankar@intel.com> Cc: Ricardo Neri <ricardo.neri@intel.com> Cc: Stephane Eranian <eranian@google.com> Cc: Stephen Boyd <swboyd@chromium.org> Cc: Sumit Garg <sumit.garg@linaro.org> Cc: Tzung-Bi Shih <tzungbi@chromium.org> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Patch series "watchdog/hardlockup: Add the buddy hardlockup detector", v5.
This patch series adds the "buddy" hardlockup detector. In brief, the
buddy hardlockup detector can detect hardlockups without arch-level
support by having CPUs checkup on a "buddy" CPU periodically.
Given the new design of this patch series, testing all combinations is
fairly difficult. I've attempted to make sure that all combinations of
CONFIG_ options are good, but it wouldn't surprise me if I missed
something. I apologize in advance and I'll do my best to fix any
problems that are found.
This patch (of 18):
The real watchdog_update_hrtimer_threshold() is defined in
kernel/watchdog_hld.c. That file is included if
CONFIG_HARDLOCKUP_DETECTOR_PERF and the function is defined in that file
if CONFIG_HARDLOCKUP_CHECK_TIMESTAMP.
The dummy version of the function in "nmi.h" didn't get that quite right.
While this doesn't appear to be a huge deal, it's nice to make it
consistent.
It doesn't break builds because CHECK_TIMESTAMP is only defined by x86 so
others don't get a double definition, and x86 uses perf lockup detector,
so it gets the out of line version.
Link: https://lkml.kernel.org/r/20230519101840.v5.18.Ia44852044cdcb074f387e80df6b45e892965d4a1@changeid Link: https://lkml.kernel.org/r/20230519101840.v5.1.I8cbb2f4fa740528fcfade4f5439b6cdcdd059251@changeid Fixes: 7edaeb6841df ("kernel/watchdog: Prevent false positives with turbo modes") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Guenter Roeck <groeck@chromium.org> Cc: Ian Rogers <irogers@google.com> Cc: Lecopzer Chen <lecopzer.chen@mediatek.com> Cc: Marc Zyngier <maz@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Masayoshi Mizuma <msys.mizuma@gmail.com> Cc: Matthias Kaehlcke <mka@chromium.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Pingfan Liu <kernelfans@gmail.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: "Ravi V. Shankar" <ravi.v.shankar@intel.com> Cc: Ricardo Neri <ricardo.neri@intel.com> Cc: Stephane Eranian <eranian@google.com> Cc: Stephen Boyd <swboyd@chromium.org> Cc: Sumit Garg <sumit.garg@linaro.org> Cc: Tzung-Bi Shih <tzungbi@chromium.org> Cc: Will Deacon <will@kernel.org> Cc: Colin Cross <ccross@android.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A bad USB device is able to construct a service connection response
message with target endpoint being ENDPOINT0 which is reserved for
HTC_CTRL_RSVD_SVC and should not be modified to be used for any other
services.
Reject such service connection responses.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: fb9987d0f748 ("ath9k_htc: Support for AR9271 chipset.") Reported-by: syzbot+b68fbebe56d8362907e8@syzkaller.appspotmail.com Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230516150427.79469-1-pchelkin@ispras.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
For the reasons also described in commit b383e8abed41 ("wifi: ath9k: avoid
uninit memory read in ath9k_htc_rx_msg()"), ath9k_htc_rx_msg() should
validate pkt_len before accessing the SKB.
For example, the obtained SKB may have been badly constructed with
pkt_len = 8. In this case, the SKB can only contain a valid htc_frame_hdr
but after being processed in ath9k_htc_rx_msg() and passed to
ath9k_wmi_ctrl_rx() endpoint RX handler, it is expected to have a WMI
command header which should be located inside its data payload.
Implement sanity checking inside ath9k_wmi_ctrl_rx(). Otherwise, uninit
memory can be referenced.
Tested on Qualcomm Atheros Communications AR9271 802.11n .
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: fb9987d0f748 ("ath9k_htc: Support for AR9271 chipset.") Reported-and-tested-by: syzbot+f2cb6e0ffdb961921e4d@syzkaller.appspotmail.com Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230424183348.111355-1-pchelkin@ispras.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix ath9k_hw_verify_hang()/ar9003_hw_detect_mac_hang() register offset
calculation (do not overflow the shift for the second register/queues
above five, use the register layout described in the comments above
ath9k_hw_verify_hang() instead).
Currently, while calculating residency and latency values, right
operands may overflow if resulting values are big enough.
To prevent this, albeit unlikely case, play it safe and convert
right operands to left ones' type s64.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 30f604283e05 ("PM / Domains: Allow domain power states to be read from DT") Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When removing a disk with replacement, the replacement will be used to
replace rdev. During this process, there is a brief window in which both
rdev and replacement are read as NULL in raid10_write_request(). This
will result in io not being submitted but it should be.
Fix it by reading replacement first and rdev later, meanwhile, use smp_mb()
to prevent memory reordering.
Fixes: 475b0321a4df ("md/raid10: writes should get directed to replacement as well as original.") Signed-off-by: Li Nan <linan122@huawei.com> Reviewed-by: Yu Kuai <yukuai3@huawei.com> Signed-off-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20230602091839.743798-3-linan666@huaweicloud.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no input check when echo md/safe_mode_delay in safe_delay_store().
And msec might also overflow when HZ < 1000 in safe_delay_show(), Fix it by
checking overflow in safe_delay_store() and use unsigned long conversion in
safe_delay_show().
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
gtags considers any file outside of its current working directory
"outside the source tree" and refuses to index it. For O= kernel builds,
or when "make" is invoked from a directory other then the kernel source
tree, gtags ignores the entire kernel source and generates an empty
index.
Force-set gtags current working directory to the kernel source tree.
Due to commit 9da0763bdd82 ("kbuild: Use relative path when building in
a subdir of the source tree"), if the kernel build is done in a
sub-directory of the kernel source tree, the kernel Makefile will set
the kernel's $srctree to ".." for shorter compile-time and run-time
warnings. Consequently, the list of files to be indexed will be in the
"../*" form, rendering all such paths invalid once gtags switches to the
kernel source tree as its current working directory.
If gtags indexing is requested and the build directory is not the kernel
source tree, index all files in absolute-path form.
Note, indexing in absolute-path form will not affect the generated
index, as paths in gtags indices are always relative to the gtags "root
directory" anyway (as evidenced by "gtags --dump").
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de> Cc: <stable@vger.kernel.org> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Noticed this when trying to compile with -Wall on a kernel fork. We
potentially don't set width here, which causes the compiler to complain
about width potentially being uninitialized in drm_cvt_modes(). So, let's
fix that.
Changes since v1:
* Don't emit an error as this code isn't reachable, just mark it as such
Changes since v2:
* Remove now unused variable
A use-after-free bug may occur if init_imstt invokes framebuffer_release
and free the info ptr. The caller, imsttfb_probe didn't notice that and
still keep the ptr as private data in pdev.
If we remove the driver which will call imsttfb_remove to make cleanup,
UAF happens.
Fix it by return error code if bad case happens in init_imstt.
Monitoring idletask::thread_info::flags in mwait_play_dead() has been an
obvious choice as all what is needed is a cache line which is not written
by other CPUs.
But there is a use case where a "dead" CPU needs to be brought out of
MWAIT: kexec().
This is required as kexec() can overwrite text, pagetables, stacks and the
monitored cacheline of the original kernel. The latter causes MWAIT to
resume execution which obviously causes havoc on the kexec kernel which
results usually in triple faults.
Use a dedicated per CPU storage to prepare for that.
On corrupt gfs2 file systems the evict code can try to reference the
journal descriptor structure, jdesc, after it has been freed and set to
NULL. The sequence of events is:
init_journal()
...
fail_jindex:
gfs2_jindex_free(sdp); <------frees journals, sets jdesc = NULL
if (gfs2_holder_initialized(&ji_gh))
gfs2_glock_dq_uninit(&ji_gh);
fail:
iput(sdp->sd_jindex); <--references jdesc in evict_linked_inode
evict()
gfs2_evict_inode()
evict_linked_inode()
ret = gfs2_trans_begin(sdp, 0, sdp->sd_jdesc->jd_blocks);
<------references the now freed/zeroed sd_jdesc pointer.
The call to gfs2_trans_begin is done because the truncate_inode_pages
call can cause gfs2 events that require a transaction, such as removing
journaled data (jdata) blocks from the journal.
This patch fixes the problem by adding a check for sdp->sd_jdesc to
function gfs2_evict_inode. In theory, this should only happen to corrupt
gfs2 file systems, when gfs2 detects the problem, reports it, then tries
to evict all the system inodes it has read in up to that point.
Reported-by: Yang Lan <lanyang0908@gmail.com> Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
[DP: adjusted context] Signed-off-by: Dragos-Marian Panait <dragos.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the way the GDS and SRSO patches flowed into the stable tree, it
was a 50% chance that the merge of the which value GDS and SRSO should
be. Of course, I lost that bet, and chose the opposite of what Linus
chose in commit 64094e7e3118 ("Merge tag 'gds-for-linus-2023-08-01' of
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip")
Fix this up by switching the values to match what is now in Linus's tree
as that is the correct value to mirror.
It is possible that a guest can send a packet that contains a head + 18
slots and yet has a len <= XEN_NETBACK_TX_COPY_LEN. This causes nr_slots
to underflow in xenvif_get_requests() which then causes the subsequent
loop's termination condition to be wrong, causing a buffer overrun of
queue->tx_map_ops.
Rework the code to account for the extra frag_overflow slots.
This is CVE-2023-34319 / XSA-432.
Fixes: ad7f402ae4f4 ("xen/netback: Ensure protocol headers don't fall in the non-linear area") Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by: Paul Durrant <paul@xen.org> Reviewed-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gather Data Sampling (GDS) is a transient execution attack using
gather instructions from the AVX2 and AVX512 extensions. This attack
allows malicious code to infer data that was previously stored in
vector registers. Systems that are not vulnerable to GDS will set the
GDS_NO bit of the IA32_ARCH_CAPABILITIES MSR. This is useful for VM
guests that may think they are on vulnerable systems that are, in
fact, not affected. Guests that are running on affected hosts where
the mitigation is enabled are protected as if they were running
on an unaffected system.
On all hosts that are not affected or that are mitigated, set the
GDS_NO bit.
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Acked-by: Josh Poimboeuf <jpoimboe@kernel.org> Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gather Data Sampling (GDS) is mitigated in microcode. However, on
systems that haven't received the updated microcode, disabling AVX
can act as a mitigation. Add a Kconfig option that uses the microcode
mitigation if available and disables AVX otherwise. Setting this
option has no effect on systems not affected by GDS. This is the
equivalent of setting gather_data_sampling=force.
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Acked-by: Josh Poimboeuf <jpoimboe@kernel.org> Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Gather Data Sampling (GDS) vulnerability allows malicious software
to infer stale data previously stored in vector registers. This may
include sensitive data such as cryptographic keys. GDS is mitigated in
microcode, and systems with up-to-date microcode are protected by
default. However, any affected system that is running with older
microcode will still be vulnerable to GDS attacks.
Since the gather instructions used by the attacker are part of the
AVX2 and AVX512 extensions, disabling these extensions prevents gather
instructions from being executed, thereby mitigating the system from
GDS. Disabling AVX2 is sufficient, but we don't have the granularity
to do this. The XCR0[2] disables AVX, with no option to just disable
AVX2.
Add a kernel parameter gather_data_sampling=force that will enable the
microcode mitigation if available, otherwise it will disable AVX on
affected systems.
This option will be ignored if cmdline mitigations=off.
This is a *big* hammer. It is known to break buggy userspace that
uses incomplete, buggy AVX enumeration. Unfortunately, such userspace
does exist in the wild:
Gather Data Sampling (GDS) is a hardware vulnerability which allows
unprivileged speculative access to data which was previously stored in
vector registers.
Intel processors that support AVX2 and AVX512 have gather instructions
that fetch non-contiguous data elements from memory. On vulnerable
hardware, when a gather instruction is transiently executed and
encounters a fault, stale data from architectural or internal vector
registers may get transiently stored to the destination vector
register allowing an attacker to infer the stale data using typical
side channel techniques like cache timing attacks.
This mitigation is different from many earlier ones for two reasons.
First, it is enabled by default and a bit must be set to *DISABLE* it.
This is the opposite of normal mitigation polarity. This means GDS can
be mitigated simply by updating microcode and leaving the new control
bit alone.
Second, GDS has a "lock" bit. This lock bit is there because the
mitigation affects the hardware security features KeyLocker and SGX.
It needs to be enabled and *STAY* enabled for these features to be
mitigated against GDS.
The mitigation is enabled in the microcode by default. Disable it by
setting gather_data_sampling=off or by disabling all mitigations with
mitigations=off. The mitigation status can be checked by reading:
Initializing the FPU during the early boot process is a pointless
exercise. Early boot is convoluted and fragile enough.
Nothing requires that the FPU is set up early. It has to be initialized
before fork_init() because the task_struct size depends on the FPU register
buffer size.
Move the initialization to arch_cpu_finalize_init() which is the perfect
place to do so.
No functional change.
This allows to remove quite some of the custom early command line parsing,
but that's subject to the next installment.
X86 is reworking the boot process so that initializations which are not
required during early boot can be moved into the late boot process and out
of the fragile and restricted initial boot phase.
arch_cpu_finalize_init() is the obvious place to do such initializations,
but arch_cpu_finalize_init() is invoked too late in start_kernel() e.g. for
initializing the FPU completely. fork_init() requires that the FPU is
initialized as the size of task_struct on X86 depends on the size of the
required FPU register buffer.
Fortunately none of the init calls between calibrate_delay() and
arch_cpu_finalize_init() is relevant for the functionality of
arch_cpu_finalize_init().
Invoke it right after calibrate_delay() where everything which is relevant
for arch_cpu_finalize_init() has been set up already.
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Link: https://lore.kernel.org/r/20230613224545.612182854@linutronix.de Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Everything is converted over to arch_cpu_finalize_init(). Remove the
check_bugs() leftovers including the empty stubs in asm-generic, alpha,
parisc, powerpc and xtensa.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Link: https://lore.kernel.org/r/20230613224545.553215951@linutronix.de Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
check_bugs() has become a dumping ground for all sorts of activities to
finalize the CPU initialization before running the rest of the init code.
Most are empty, a few do actual bug checks, some do alternative patching
and some cobble a CPU advertisement string together....
Aside of that the current implementation requires duplicated function
declaration and mostly empty header files for them.
Provide a new function arch_cpu_finalize_init(). Provide a generic
declaration if CONFIG_ARCH_HAS_CPU_FINALIZE_INIT is selected and a stub
inline otherwise.
This requires a temporary #ifdef in start_kernel() which will be removed
along with check_bugs() once the architectures are converted over.
Claim clkhi and clklo as integer type to avoid possible calculation
errors caused by data overflow.
Fixes: a55fa9d0e42e ("i2c: imx-lpi2c: add low power i2c bus driver") Signed-off-by: Clark Wang <xiaoning.wang@nxp.com> Signed-off-by: Carlos Song <carlos.song@nxp.com> Reviewed-by: Andi Shyti <andi.shyti@kernel.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When booting with "intremap=off" and "x2apic_phys" on the kernel command
line, the physical x2APIC driver ends up being used even when x2APIC
mode is disabled ("intremap=off" disables x2APIC mode). This happens
because the first compound condition check in x2apic_phys_probe() is
false due to x2apic_mode == 0 and so the following one returns true
after default_acpi_madt_oem_check() having already selected the physical
x2APIC driver.
Userspace can race to free the gobj(robj converted from), robj should not
be accessed again after drm_gem_object_put, otherwith it will result in
use-after-free.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Min Li <lm0963hack@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
