Paul Fertser [Sun, 22 Dec 2019 18:20:57 +0000 (21:20 +0300)]
kernel: ath10k-ct: provide a build variant for small RAM devices
According to many bugreports [0][1][2] the default ath10k-ct kernel
module is unusable on devices with just 64 MiB RAM or with 128 MiB and
dual ath10k cards. The target boards boot but eventually oom-killer
starts to interfere with normal operation, so the current state is
effectively broken.
Since the two patches in question have a performance impact (and
possibly some other unexpected side-effects) a dedicated build variant
is added so that users of the low RAM devices can still benefit from all
the ath10k-ct advantages.
According to testing [3] results, the issue can be experienced even with
"a 256MB device with three radios". Measured performance impact of
implementing small buffers was lowering "the maximum 5 GHz throughput on
an IPQ40xx device without RPS/XPS optimizations from 494/432 Mbit/s for
TCP transfers (download/upload) to 438/343 Mbit/s"
The patches were apparently inspired by QSDK tweaks used by ODMs for the
affected devices.
Hauke Mehrtens [Mon, 23 Dec 2019 14:23:09 +0000 (15:23 +0100)]
kernel: Deactivate CONFIG_SFP in generic config
Deactivate CONFIG_SFP for kernel 4.19 in the generic configuration.
The CONFIG_SFP configuration option was not set to anything in the
ath79 build for me, set it to deactivated by default.
ramips: simplify state_default/pinctrl0 in device DTS files
The node pinctrl0 is already set up in the SOC DTSI files, but
defined again as member of pinctrl in most of the device DTS(I)
files. This patch removes this redundancy for the entire ramips
target.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Fri, 6 Dec 2019 14:25:48 +0000 (23:25 +0900)]
kernel: fix *-gpio-custom module unloading
Unloading and reloading the modules fails, as platform_device_put() does not
release resources fully.
root@OpenWrt:/# insmod i2c-gpio-custom bus0=0,18,0,5
[ 196.860620] Custom GPIO-based I2C driver version 0.1.1
[ 196.871162] ------------[ cut here ]------------
[ 196.880517] WARNING: CPU: 0 PID: 1365 at fs/sysfs/dir.c:31 0x80112158
[ 196.893431] sysfs: cannot create duplicate filename '/devices/platform/i2c-gpio.0'
...
[ 197.513200] kobject_add_internal failed for i2c-gpio.0 with -EEXIST, don't try to register things with the same name in the same directory.
This patch fixes it by replacing platform_device_put() to
platform_device_unregister().
Fixes: da7740853715 ("i2c-gpio-custom: minor bugfix") Fixes: 3bc81edc70e8 ("package: fix w1-gpio-custom package (closes #6770)") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Florian Eckert [Thu, 7 Nov 2019 13:31:29 +0000 (14:31 +0100)]
rpcd: add respawn param
The rpcd service is an important service, but if the service stops
working for any reason, no one will ever respawn that service. With this
commit, the procd service will monitor if the rpcd service
is running. If the rpcd service has crashed, then
procd respawns the rpcd service.
Rosen Penev [Sun, 17 Nov 2019 21:42:04 +0000 (13:42 -0800)]
cmake: Install host packages to lib instead of lib64
Several CMake packages such as log4cplus and protobuf(-c) install to
lib64 instead of lib on some hosts. This completely breaks rpath linking.
Override it globally to avoid fixing each package individually.
Signed-off-by: Rosen Penev <rosenp@gmail.com> Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Bjørn Mork [Tue, 19 Nov 2019 13:37:24 +0000 (14:37 +0100)]
adb: fix for SuperSpeed devices
The USB descriptor parsing in adb fails to detect SuperSpeed devices
because of the SuperSpeed Endpoint Companion Descriptor. This
cherry-picks the upstream fix for the problem.
Unfortunately there never were a release with this fix before the
conversion to C++, so upgrading to a newer version isn't an option.
This makes adb work with SuperSpeed devices like the Sierra Wireless
EM7565. Tested and verified.
Rosen Penev [Sat, 14 Dec 2019 05:07:04 +0000 (21:07 -0800)]
libcxx: Add package
Currently in OpenWrt, there are two libc++: libstdcpp and uClibc++. The
former is huge and the latter supports only C++98 with some basic support
for C++11. Those C++ versions seem to be specific to the compiler version
libcxx supports C++11 and above while being much smaller than libstdcpp.
On mt7621, these are the sizes of the ipks that I get:
libstdcpp: 460786
libcxx: 182881
uClibc++:67720
libcxx is faster than uClibc++ and is under active development as part of
the LLVM project while uClibc++ is effectively dead.
This PR modifies uclibc++.mk to expose the make menuconfig option. Further
cleanup is beyond the scope of this PR. What that means is, this is not
used by default.
A g++-libcxx wrapper based on the uClibc++ one was added. Works the same
way.
Compile tested with all packages that use uclibc++.mk in their Makefiles
under mipsel_24kc. kismet fails compilation but that package needs to be
cleaned up and updated.
Runtime tested with gddrescue, gdisk, dcwapd, bonnie++, and aircrack-ng
on a TP-Link Archer C7v2.
John Sommerville [Fri, 27 Sep 2019 20:09:10 +0000 (14:09 -0600)]
build: build proper VMDK formats for ESXI 6.5
VMWare ESXI 6.5 and above is not compatible with
subformat=monolithicSparse (The default qemu-img convert -O VMDK option).
Monolithic Sparse vmdk can be imported, but issues occur when running
sysupgrade with new images and other tasks that modify the file system
(issues like Kernel panics, reboot loops, sometimes crashing the Host ESXI
box).
This change creates an additional VMDK output file for ESXI that sets the
subformat to monlithicFlat, and the adapter_type to the SCSI lsilogic
controller.
* No changes to wave-1, but I make a version .014 copy anyway to keep
the makefile in sync.
The release notes since last time for wave-2:
* December 16, 2019: Wave-2 has a fix to make setting txpower work
better. Before setting the power was ignored at
least some of the time (it also appeared to work
mostly, so I guess it was being correctly set in
other ways).
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Sungbo Eo [Sun, 22 Dec 2019 14:47:24 +0000 (23:47 +0900)]
ramips: further improve support for Xiaomi MiWiFi Nano
This patch does the following:
- prepend vendor name to model
- set status LEDs to follow the behavior in stock FW
- simplify state_default node definition
- use generic name for flash node
Stock FW status indicators:
https://files.xiaomi-mi.com/files/Mi_Router_Wi-Fi_Nano/Mi_router-NANO_EN.pdf
> Yellow: power on / off
> Blue: during normal operation
> Red: in case of problems with the operation of the device
lantiq: dts: assign the ASC pins to the serial controller node
Assign the ASC pins to the serial controller node instead of using pin
hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
lantiq: dts: assign the PCI pins to the PCI controller node
Assign the PCI pins to the PCI controller node instead of using pin
hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
lantiq: dts: assign the STP pins to the STP GPIO controller node
Assign the STP pins to the STP GPIO controller node instead of using
pin hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
lantiq: dts: assign the GPHY LED pins to the Ethernet controller node
Assign the GPHY LED pins to the Ethernet controller node instead of
using pin hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
lantiq: dts: assign the NAND pins to the nand-controller node
Assign the NAND pins to the NAND controller node instead of using pin
hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
While here, define all NAND pins (CLE, ALE, read/RD, ready busy/RDY and
CE/CS1). This means that the pinctrl subsystem knows that these pins are
in use and cannot be re-assigned as GPIOs for example.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
lantiq: dts: define the SPI pins in {amazonse,ar9,vr9}.dtsi
Define the SPI pins in the corresponding SoCs.dtsi and assign them to
the SPI controller node. All known boards use CS4 and it's likely that
this is hardcoded in bootrom so this doesn't bother with having
per-board SPI pinmux settings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Assign the MDIO pins to the switch node instead of using pin hogging
(where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.
This converts amazonse, ar9 and vr9. danube is skipped because the pin
controller doesn't define a pinmux for the MDIO pins (some of the SoC
pads may be hardwired to the MDIO pins instead of being configurable).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
So far, lan/wan MAC address for Edimax RG21S are only read using
mtd_get_mac_ascii, so eth0.1 and eth0.2 addresses are set, but
eth0 address is random. Since the device's LAN address is the same
as for 2.4 GHz, though, this patch set's the eth0 address based
on the 2.4 GHz one, which can be extracted by mtd-mac-address.
This will also allow to move the label MAC address setup to DT.
The setup of lan_mac and wan_mac are kept in 02_network, so those
locations are still in use, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Sat, 21 Dec 2019 03:43:40 +0000 (12:43 +0900)]
ipq40xx: improve ASUS RT-AC58U support
This patch does the following:
- move WiFi LED setup to DTS
- fix LAN/WAN MAC addresses and add label MAC address
- wan5G -> wlan5G, power -> led_power
- increase flash SPI frequency to 30MHz
MAC addresses are stored in Factory partition at:
0x1006: WiFi 2.4GHz, WAN (label_mac)
0x5006: WiFi 5GHz, LAN (label_mac +4)
By improving flash speed,
`time dd if=/dev/mtdblock8 of=/dev/null bs=2k`
is reduced from 7m 10.26s to 5m 9.52s.
Using higher frequencies did not improve speed further.
To connect to the serial console, you can solder to the labled pads next
to the USB port or use your Aruba supplied UARt adapter.
Do NOT plug a standard USB cable into the Console labled USB-port!
Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself
an adapter cable:
VCC - NC
D+ - TX
D- - RX
GND - GND
The console setting in bootloader and OS is 9600 8N1. Voltage level is
3.3V.
To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.
Installation
------------
1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
into the TFTP server root directory. Configure the TFTP server to
be reachable at 192.168.1.75/24. Connect the machine running the TFTP
server to the ethernet port of the access point.
2. Connect to the serial console. Interrupt autobooting by pressing
Enter when prompted.
3. Configure the bootargs and bootcmd for OpenWrt.
$ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8"
$ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
ubi read 0x85000000 kernel; bootm 0x85000000"
$ setenv ramboot_openwrt "run bootargs_openwrt;
setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
netget; set fdt_high 0x87000000; bootm"
$ setenv bootcmd "run nandboot_openwrt"
$ saveenv
4. Load OpenWrt into RAM:
$ run ramboot_openwrt
5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
/tmp folder on the device.
Sungbo Eo [Mon, 11 Nov 2019 16:19:03 +0000 (01:19 +0900)]
ramips: fix USB LED for Belkin F9K1109v1
Device support for Belkin F9K1109v1 was added using set_usb_led()
although this was removed in 772b27c20736 ("ramips: set F5D8235 v1
usb led trigger via devicetree").
Use ucidef_set_led_usbport() instead.
Fixes: f2c83532f92c ("ramips: add support for Belkin F9K1109v1") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rephrase commit title and message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This harmonizes the line wrapping in image Makefile device
definitions, as those are frequently copy-pasted and are a common
subject of review comments. Having the treatment unifying should
reduce the cases where adjustment is necessary afterwards.
Harmonization is achieved by consistently (read "strictly")
applying certain rules:
- Never put more than 80 characters into one line
- Fill lines up (do not break after 40 chars because of ...)
- Use one tab for indent after wrapping by "\"
- Only break after pipe "|" for IMAGE variables
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This harmonizes the line wrapping in image Makefile device
definitions, as those are frequently copy-pasted and are a common
subject of review comments. Having the treatment unifying should
reduce the cases where adjustment is necessary afterwards.
Harmonization is achieved by consistently (read "strictly")
applying certain rules:
- Never put more than 80 characters into one line
- Fill lines up (do not break after 40 chars because of ...)
- Use one tab for indent after wrapping by "\"
- Only break after pipe "|" for IMAGE variables
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Paul Fertser [Tue, 26 Nov 2019 13:01:11 +0000 (16:01 +0300)]
ath79-tiny: enable 4k sectors
This enables using 4kiB sectors as erase blocks for 4MiB NOR flash ICs
that support it.
Writeable jffs2 overlay used to store settings requires a partition with
at least 5 erase blocks, so using small sectors is essential for devices
with 4MiB flash.
Sysupgrading a device running firmware without this feature will likely
not allow to preserve configs automatically but since ath79 is
considered to be in a "technology preview" state it shouldn't be a
problem.
Vendor firmware (based on CameoAP99) defines two additional partitions:
"mac" @0x3b0000, size 0x10000 and "lp" @0x3c0000, size 0x30000.
The "mac" partition stores LAN MAC address and hardware board name.
However, the vendor firmware uses addresses from "nvram" partition, and
the board name is used only for informational purposes in the Web
interface (included in the pages' header), not affecting the firmware
image check.
The "lp" partition is supposed to contain a "language pack" (which can
be used to add an additional language support to the Web interface) and
is flashed separately, using the vendor firmware upgrade page.
Since these partitions are absolutely useless for OpenWrt and
overwriting them doesn't prevent downgrading to obsolete vendor
firmware, this patch appends the valueable space to "firmware".
Installation instructions:
- Upgrade from OpenWrt ar71xx with "sysupgrade -f -n"
or
- Upload as a firmware update via the vendor Web-interface
or
- Connect UART and use "loady" to upload and run OpenWrt initramfs
image, then sysupgrade from it (TFTP client doesn't work)
or
- Before powering up hold "reset" button and keep it pressed for about
15 seconds after, then access fail safe Web server on 192.168.0.1 (the
old uIP TCP/IP protocol stack is not compatible with modern Linux, the
kernel, so you'll need to use some other OS to do this). Can be
performed without a Web-browser too:
curl http://192.168.0.1/cgi/index \
-F Send=@openwrt-ath79-tiny-dlink_dir-615-e4-squashfs-factory.bin
ath79: enable all space on Netgear ar9344-based WNDR routers
Netgear WNDR routers (AR9344 models) like WNDR4300 have 128 MiB of flash
memory but only first 32 MiB are used now - both by vendor's firmware and
OpenWrt. This patch concatenates two regions of flash memory: ubi part
of firmware partition and reserved (unused) space beyond 'caldata_backup'
while preserving ART backup. No data is wiped or moved away.
This increases area for OS ubi volumes from 23 to 119 Megabytes.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Paul Fertser [Tue, 10 Dec 2019 14:24:20 +0000 (17:24 +0300)]
base-files: send informational UDP message each second waiting
The preinit network initialisation and failsafe informational message
are inherently racy as the interface takes some time to become
functional after "ip link set $pi_ifname up" command.
Consider this timing:
[ 12.002713] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 12.008819] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[ 12.118877] random: procd: uninitialized urandom read (4 bytes read)
[ 13.068614] eth1: link up (1000Mbps/Full duplex)
[ 13.073309] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 13.080445] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.1: link becomes ready
Since the UDP message was sent prior to link becoming ready, it was
never seen on the wire.
The default failsafe timeout is set to 2 seconds, so with this patch
there are two attempts to send the message, one spent in vain, and the
other visible in tcpdump on an attached host. Of course, in cases when
the interface is brought up faster it leads to two messages, however it
should be harmless. This patch (almost) doesn't affect normal boot time
while still allowing to enter failsafe reliably with a single button
press, matching the official "generic failsafe" documentation.
Ansuel Smith [Thu, 28 Nov 2019 21:29:15 +0000 (22:29 +0100)]
ipq806x: fix tsens driver in 4.19
Added patch:
- 063-3 Fix tsense shared memory problem
Recent changes in ioremap_resource function are causing fails for the
memory areas which are already mapped. This changes are causing tsense
driver failures during initialization:
Improve rediability of gpio mdio list. No functional change.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch] Signed-off-by: Petr Štetiar <ynezz@true.cz>
From documentation
https://www.kernel.org/doc/Documentation/devicetree/bindings/chosen.txt
should be just stdout-path
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch] Signed-off-by: Petr Štetiar <ynezz@true.cz>
Increase drive-strength from
https://lore.kernel.org/patchwork/patch/626885/
2mA drive strength is not enough when we connect multiple i2c devices
on the bus with different pull up resistors.
This issue was detected when multiple i2c devices
connected on the other side of level shifters on Linaro sensor board.
Maxing up to 16mA made i2c much stable.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Convert hardcoded interrupts value to types defined in gci include file.
Interrupts sets to 0 are converted to IRQ_TYPE_LEVEL_HIGH to fix
kernel warning. Same fix has been applied to arm64 dts.
Use new usb3 implementation and refresh dts to the new dwc3 structure
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch] Signed-off-by: Petr Štetiar <ynezz@true.cz>
- ipq8064 compatible was missing from nbg6817.
- Rename ap148 with a better descriptive name.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch] Signed-off-by: Petr Štetiar <ynezz@true.cz>
- 310-msm-adhoc-bus-support
(it looks like it was never actually used in any dts)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[commit subject and description facelift, SoB fix] Signed-off-by: Petr Štetiar <ynezz@true.cz>
Ansuel Smith [Sun, 15 Dec 2019 13:06:02 +0000 (14:06 +0100)]
ipq806x: update 4.19 kernel config
These changes are needed in order to migrate old kernel 4.14 config to
the upcoming kernel version 4.19. Also add missing configuration
options that comes up with this SoC.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[line wrap long commit description, add 4.19 to subject, soc->SoC] Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit replaced gpio-exports in favor of gpio-hogs for enabling USB
power at boot, but this rids the user of control of the USB port power
present on this device for a long time. It was agreed on a mailing list
[1] that this is not the way to go, and this patch breaks a very common
use-case of WWAN modem reset by power cycle, used on a lot USB equipped
routers, hence revert this change until a better solution can be found.
Lech Perczak [Sun, 1 Dec 2019 18:31:32 +0000 (19:31 +0100)]
ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Rafał Miłecki [Thu, 19 Dec 2019 07:40:12 +0000 (08:40 +0100)]
mac80211: brcm: backport 5.5 and 5.6 kernel patches
This update doesn't include: 3b1e0a7bdfee brcmfmac: add support for SAE authentication offload be898fed355e brcmfmac: send port authorized event for FT-802.1X
due to nl80211 dependencies.
1ec6ece version: bump snapshot e13de91 main: remove unused include <linux/version.h> 72eb17c wg-quick: linux: support older nft(8) 1d8e978 global: fix up spelling e02713e wg-quick: linux: add support for nft and prefer it b4e3a83 compat: support building for RHEL-8.1 instead of RHEL-8.0 f29e3ac socket: convert to ipv6_dst_lookup_flow for 5.5
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
projects / thirdparty / openwrt.git / log
