The freq_tables[] array has num_possible_cpus() elements so, to avoid an
out of bounds access, this loop should be capped at "< nb_cpus" instead
of "<= nb_cpus". The freq_tables[] array is allocated in
armada_8k_cpufreq_init().
Cc: stable@vger.kernel.org Fixes: f525a670533d ("cpufreq: ap806: add cpufreq driver for Armada 8K") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the PSLVERR_RESP_EN parameter is set to 1, the device generates
an error response if an attempt is made to read an empty RBR (Receive
Buffer Register) while the FIFO is enabled.
In serial8250_do_startup(), calling serial_port_out(port, UART_LCR,
UART_LCR_WLEN8) triggers dw8250_check_lcr(), which invokes
dw8250_force_idle() and serial8250_clear_and_reinit_fifos(). The latter
function enables the FIFO via serial_out(p, UART_FCR, p->fcr).
Execution proceeds to the serial_port_in(port, UART_RX).
This satisfies the PSLVERR trigger condition.
When another CPU (e.g., using printk()) is accessing the UART (UART
is busy), the current CPU fails the check (value & ~UART_LCR_SPAR) ==
(lcr & ~UART_LCR_SPAR) in dw8250_check_lcr(), causing it to enter
dw8250_force_idle().
Put serial_port_out(port, UART_LCR, UART_LCR_WLEN8) under the port->lock
to fix this issue.
RCU re-initializes the deferred QS irq work everytime before attempting
to queue it. However there are situations where the irq work is
attempted to be queued even though it is already queued. In that case
re-initializing messes-up with the irq work queue that is about to be
handled.
The chances for that to happen are higher when the architecture doesn't
support self-IPIs and irq work are then all lazy, such as with the
following sequence:
1) rcu_read_unlock() is called when IRQs are disabled and there is a
grace period involving blocked tasks on the node. The irq work
is then initialized and queued.
2) The related tasks are unblocked and the CPU quiescent state
is reported. rdp->defer_qs_iw_pending is reset to DEFER_QS_IDLE,
allowing the irq work to be requeued in the future (note the previous
one hasn't fired yet).
3) A new grace period starts and the node has blocked tasks.
4) rcu_read_unlock() is called when IRQs are disabled again. The irq work
is re-initialized (but it's queued! and its node is cleared) and
requeued. Which means it's requeued to itself.
5) The irq work finally fires with the tick. But since it was requeued
to itself, it loops and hangs.
Fix this with initializing the irq work only once before the CPU boots.
Fixes: b41642c87716 ("rcu: Fix rcu_read_unlock() deadloop due to IRQ work") Reported-by: kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202508071303.c1134cce-lkp@intel.com Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Reviewed-by: Joel Fernandes <joelagnelf@nvidia.com> Signed-off-by: Neeraj Upadhyay (AMD) <neeraj.upadhyay@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the battery timer is set up for all devices using hid-apple,
irrespective of whether they actually have a battery or not.
APPLE_RDESC_BATTERY is a quirk that indicates the device has a battery
and needs the battery timer. This patch checks for this quirk before
setting up the timer, ensuring that only devices with a battery will
have the timer set up.
Currently, the battery timer is set up for all devices using
hid-magicmouse, irrespective of whether they actually need it or not.
The current implementation requires the battery timer for Magic Mouse 2
and Magic Trackpad 2 when connected via USB only. Add checks to ensure
that the battery timer is only set up when they are connected via USB.
Ever since commit c2ff29e99a76 ("siw: Inline do_tcp_sendpages()"),
we have been doing this:
static int siw_tcp_sendpages(struct socket *s, struct page **page, int offset,
size_t size)
[...]
/* Calculate the number of bytes we need to push, for this page
* specifically */
size_t bytes = min_t(size_t, PAGE_SIZE - offset, size);
/* If we can't splice it, then copy it in, as normal */
if (!sendpage_ok(page[i]))
msg.msg_flags &= ~MSG_SPLICE_PAGES;
/* Set the bvec pointing to the page, with len $bytes */
bvec_set_page(&bvec, page[i], bytes, offset);
/* Set the iter to $size, aka the size of the whole sendpages (!!!) */
iov_iter_bvec(&msg.msg_iter, ITER_SOURCE, &bvec, 1, size);
try_page_again:
lock_sock(sk);
/* Sendmsg with $size size (!!!) */
rv = tcp_sendmsg_locked(sk, &msg, size);
This means we've been sending oversized iov_iters and tcp_sendmsg calls
for a while. This has a been a benign bug because sendpage_ok() always
returned true. With the recent slab allocator changes being slowly
introduced into next (that disallow sendpage on large kmalloc
allocations), we have recently hit out-of-bounds crashes, due to slight
differences in iov_iter behavior between the MSG_SPLICE_PAGES and
"regular" copy paths:
(MSG_SPLICE_PAGES)
skb_splice_from_iter
iov_iter_extract_pages
iov_iter_extract_bvec_pages
uses i->nr_segs to correctly stop in its tracks before OoB'ing everywhere
skb_splice_from_iter gets a "short" read
(!MSG_SPLICE_PAGES)
skb_copy_to_page_nocache copy=iov_iter_count
[...]
copy_from_iter
/* this doesn't help */
if (unlikely(iter->count < len))
len = iter->count;
iterate_bvec
... and we run off the bvecs
Fix this by properly setting the iov_iter's byte count, plus sending the
correct byte count to tcp_sendmsg_locked.
Link: https://patch.msgid.link/r/20250729120348.495568-1-pfalcato@suse.de Cc: stable@vger.kernel.org Fixes: c2ff29e99a76 ("siw: Inline do_tcp_sendpages()") Reported-by: kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202507220801.50a7210-lkp@intel.com Reviewed-by: David Howells <dhowells@redhat.com> Signed-off-by: Pedro Falcato <pfalcato@suse.de> Acked-by: Bernard Metzler <bernard.metzler@linux.dev> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While nolibc-test does test syscalls, it doesn't test as much the rest
of the macros, and a wrong spelling of FD_SETBITMASK in commit feaf75658783a broke programs using either FD_SET() or FD_CLR() without
being noticed. Let's fix these macros.
Currently, the driver performs a length check of the metadata buffer
before the actual metadata size is known and before the metadata is
decided to be copied. This results in valid metadata buffers being
incorrectly marked as invalid.
Move the length check to occur after the metadata size is determined and
is decided to be copied.
Cc: stable@vger.kernel.org Fixes: 088ead255245 ("media: uvcvideo: Add a metadata device node") Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Hans de Goede <hansg@kernel.org> Signed-off-by: Ricardo Ribalda <ribalda@chromium.org> Link: https://lore.kernel.org/r/20250707-uvc-meta-v8-1-ed17f8b1218b@chromium.org Signed-off-by: Hans de Goede <hansg@kernel.org> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, The event_seq_changed() handler processes a variable number
of properties sent by the firmware. The number of properties is indicated
by the firmware and used to iterate over the payload. However, the
payload size is not being validated against the actual message length.
This can lead to out-of-bounds memory access if the firmware provides a
property count that exceeds the data available in the payload. Such a
condition can result in kernel crashes or potential information leaks if
memory beyond the buffer is accessed.
Fix this by properly validating the remaining size of the payload before
each property access and updating bounds accordingly as properties are
parsed.
This ensures that property parsing is safely bounded within the received
message buffer and protects against malformed or malicious firmware
behavior.
The buffer length check before calling uvc_parse_format() only ensured
that the buffer has at least 3 bytes (buflen > 2), buf the function
accesses buffer[3], requiring at least 4 bytes.
This can lead to an out-of-bounds read if the buffer has exactly 3 bytes.
Fix it by checking that the buffer has at least 4 bytes in
uvc_parse_format().
Signed-off-by: Youngjun Lee <yjjuny.lee@samsung.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Fixes: c0efd232929c ("V4L/DVB (8145a): USB Video Class driver") Cc: stable@vger.kernel.org Reviewed-by: Ricardo Ribalda <ribalda@chromium.org> Link: https://lore.kernel.org/r/20250610124107.37360-1-yjjuny.lee@samsung.com Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When netpoll is enabled, calling pr_warn_once() while holding
kmemleak_lock in mem_pool_alloc() can cause a deadlock due to lock
inversion with the netconsole subsystem. This occurs because
pr_warn_once() may trigger netpoll, which eventually leads to
__alloc_skb() and back into kmemleak code, attempting to reacquire
kmemleak_lock.
Fix this by setting a flag and issuing the pr_warn_once() after
kmemleak_lock is released.
Link: https://lkml.kernel.org/r/20250731-kmemleak_lock-v1-1-728fd470198f@debian.org Fixes: c5665868183f ("mm: kmemleak: use the memory pool for early allocations") Signed-off-by: Breno Leitao <leitao@debian.org> Reported-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A soft lockup warning was observed on a relative small system x86-64
system with 16 GB of memory when running a debug kernel with kmemleak
enabled.
watchdog: BUG: soft lockup - CPU#8 stuck for 33s! [kworker/8:1:134]
The test system was running a workload with hot unplug happening in
parallel. Then kemleak decided to disable itself due to its inability to
allocate more kmemleak objects. The debug kernel has its
CONFIG_DEBUG_KMEMLEAK_MEM_POOL_SIZE set to 40,000.
The soft lockup happened in kmemleak_do_cleanup() when the existing
kmemleak objects were being removed and deleted one-by-one in a loop via a
workqueue. In this particular case, there are at least 40,000 objects
that need to be processed and given the slowness of a debug kernel and the
fact that a raw_spinlock has to be acquired and released in
__delete_object(), it could take a while to properly handle all these
objects.
As kmemleak has been disabled in this case, the object removal and
deletion process can be further optimized as locking isn't really needed.
However, it is probably not worth the effort to optimize for such an edge
case that should rarely happen. So the simple solution is to call
cond_resched() at periodic interval in the iteration loop to avoid soft
lockup.
Link: https://lkml.kernel.org/r/20250728190248.605750-1-longman@redhat.com Signed-off-by: Waiman Long <longman@redhat.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing code move the VF NIC to new namespace when NETDEV_REGISTER is
received on netvsc NIC. During deletion of the namespace,
default_device_exit_batch() >> default_device_exit_net() is called. When
netvsc NIC is moved back and registered to the default namespace, it
automatically brings VF NIC back to the default namespace. This will cause
the default_device_exit_net() >> for_each_netdev_safe loop unable to detect
the list end, and hit NULL ptr:
This issue triggers when a userspace program does an ioctl
FBIOPUT_CON2FBMAP by passing console number and frame buffer number.
Ideally this maps console to frame buffer and updates the screen if
console is visible.
As part of mapping it has to do resize of console according to frame
buffer info. if this resize fails and returns from vc_do_resize() and
continues further. At this point console and new frame buffer are mapped
and sets display vars. Despite failure still it continue to proceed
updating the screen at later stages where vc_data is related to previous
frame buffer and frame buffer info and display vars are mapped to new
frame buffer and eventully leading to out-of-bounds write in
fast_imageblit(). This bheviour is excepted only when fg_console is
equal to requested console which is a visible console and updates screen
with invalid struct references in fbcon_putcs().
[BUG]
There is an internal report that balance triggered transaction abort,
with the following call trace:
item 85 key (594509824 169 0) itemoff 12599 itemsize 33
extent refs 1 gen 197740 flags 2
ref#0: tree block backref root 7
item 86 key (594558976 169 0) itemoff 12566 itemsize 33
extent refs 1 gen 197522 flags 2
ref#0: tree block backref root 7
...
BTRFS error (device loop0): extent item not found for insert, bytenr 594526208 num_bytes 16384 parent 449921024 root_objectid 934 owner 1 offset 0
BTRFS error (device loop0): failed to run delayed ref for logical 594526208 num_bytes 16384 type 182 action 1 ref_mod 1: -117
------------[ cut here ]------------
BTRFS: Transaction aborted (error -117)
WARNING: CPU: 1 PID: 6963 at ../fs/btrfs/extent-tree.c:2168 btrfs_run_delayed_refs+0xfa/0x110 [btrfs]
And btrfs check doesn't report anything wrong related to the extent
tree.
[CAUSE]
The cause is a little complex, firstly the extent tree indeed doesn't
have the backref for 594526208.
The extent tree only have the following two backrefs around that bytenr
on-disk:
item 65 key (594509824 METADATA_ITEM 0) itemoff 13880 itemsize 33
refs 1 gen 197740 flags TREE_BLOCK
tree block skinny level 0
(176 0x7) tree block backref root CSUM_TREE
item 66 key (594558976 METADATA_ITEM 0) itemoff 13847 itemsize 33
refs 1 gen 197522 flags TREE_BLOCK
tree block skinny level 0
(176 0x7) tree block backref root CSUM_TREE
But the such missing backref item is not an corruption on disk, as the
offending delayed ref belongs to subvolume 934, and that subvolume is
being dropped:
And that offending tree block 594526208 is inside the dropped range of
that subvolume. That explains why there is no backref item for that
bytenr and why btrfs check is not reporting anything wrong.
But this also shows another problem, as btrfs will do all the orphan
subvolume cleanup at a read-write mount.
So half-dropped subvolume should not exist after an RW mount, and
balance itself is also exclusive to subvolume cleanup, meaning we
shouldn't hit a subvolume half-dropped during relocation.
The root cause is, there is no orphan item for this subvolume.
In fact there are 5 subvolumes from around 2021 that have the same
problem.
It looks like the original report has some older kernels running, and
caused those zombie subvolumes.
Thankfully upstream commit 8d488a8c7ba2 ("btrfs: fix subvolume/snapshot
deletion not triggered on mount") has long fixed the bug.
[ENHANCEMENT]
For repairing such old fs, btrfs-progs will be enhanced.
Considering how delayed the problem will show up (at run delayed ref
time) and at that time we have to abort transaction already, it is too
late.
Instead here we reject any half-dropped subvolume for reloc tree at the
earliest time, preventing confusion and extra time wasted on debugging
similar bugs.
CC: stable@vger.kernel.org # 5.15+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We call btrfs_zone_finish_one_bg() to zone finish one block group and make
room to activate another block group. Currently, we can choose a metadata
block group as a target. But, as we reserve an active metadata block group,
we no longer want to select a metadata block group. So, skip it in the
loop.
CC: stable@vger.kernel.org # 6.6+ Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we log a new inode (not persisted in a past transaction) that has 0
links and extents, then log another inode with an higher inode number, we
end up with failing to replay the log tree with -EINVAL. The steps for
this are:
1) create new file A
2) write some data to file A
3) open an fd on file A
4) unlink file A
5) fsync file A using the previously open fd
6) create file B (has higher inode number than file A)
7) fsync file B
8) power fail before current transaction commits
Now when attempting to mount the fs, the log replay will fail with
-ENOENT at replay_one_extent() when attempting to replay the first
extent of file A. The failure comes when trying to open the inode for
file A in the subvolume tree, since it doesn't exist.
Before commit 5f61b961599a ("btrfs: fix inode lookup error handling
during log replay"), the returned error was -EIO instead of -ENOENT,
since we converted any errors when attempting to read an inode during
log replay to -EIO.
The reason for this is that the log replay procedure fails to ignore
the current inode when we are at the stage LOG_WALK_REPLAY_ALL, our
current inode has 0 links and last inode we processed in the previous
stage has a non 0 link count. In other words, the issue is that at
replay_one_extent() we only update wc->ignore_cur_inode if the current
replay stage is LOG_WALK_REPLAY_INODES.
Fix this by updating wc->ignore_cur_inode whenever we find an inode item
regardless of the current replay stage. This is a simple solution and easy
to backport, but later we can do other alternatives like avoid logging
extents or inode items other than the inode item for inodes with a link
count of 0.
The problem with the wc->ignore_cur_inode logic has been around since
commit f2d72f42d5fa ("Btrfs: fix warning when replaying log after fsync
of a tmpfile") but it only became frequent to hit since the more recent
commit 5e85262e542d ("btrfs: fix fsync of files with no hard links not
persisting deletion"), because we stopped skipping inodes with a link
count of 0 when logging, while before the problem would only be triggered
if trying to replay a log tree created with an older kernel which has a
logged inode with 0 links.
If we failed to insert the tree mod log operation, we are not removing the
dirty status from the allocated and dirtied extent buffer before we free
it. Removing the dirty status is needed for several reasons such as to
adjust the fs_info->dirty_metadata_bytes counter and remove the dirty
status from the respective folios. So add the missing call to
btrfs_clear_buffer_dirty().
Fixes: f61aa7ba08ab ("btrfs: do not BUG_ON() on tree mod log failure at insert_new_root()") CC: stable@vger.kernel.org # 6.6+ Reviewed-by: Boris Burkov <boris@bur.io> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some reports of "unable to find chunk map for logical 2147483648
length 16384" error message appears in dmesg. This means some IOs are
occurring after a block group is removed.
When a metadata tree node is cleaned on a zoned setup, we keep that node
still dirty and write it out not to create a write hole. However, this can
make a block group's used bytes == 0 while there is a dirty region left.
Such an unused block group is moved into the unused_bg list and processed
for removal. When the removal succeeds, the block group is removed from the
transaction->dirty_bgs list, so the unused dirty nodes in the block group
are not sent at the transaction commit time. It will be written at some
later time e.g, sync or umount, and causes "unable to find chunk map"
errors.
This can happen relatively easy on SMR whose zone size is 256MB. However,
calling do_zone_finish() on such block group returns -EAGAIN and keep that
block group intact, which is why the issue is hidden until now.
Fixes: afba2bc036b0 ("btrfs: zoned: implement active zone tracking") CC: stable@vger.kernel.org # 6.1+ Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we failed walking a log tree during replay, we have a missing
transaction abort to prevent committing a transaction where we didn't
fully replay all the changes from a log tree and therefore can leave the
respective subvolume tree in some inconsistent state. So add the missing
transaction abort.
CC: stable@vger.kernel.org # 6.1+ Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When deciding if a zoned filesystem is reaching the threshold to reclaim
data block groups, look at the size of the filesystem not to potentially
total available size of all drives in the filesystem.
Especially if a filesystem was created with mkfs' -b option, constraining
it to only a portion of the block device, the numbers won't match and
potentially garbage collection is kicking in too late.
Fixes: 3687fcb0752a ("btrfs: zoned: make auto-reclaim less aggressive") CC: stable@vger.kernel.org # 6.1+ Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Tested-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the devices that need their endpoints to get an
initial clear_halt, this needs to be done before
the devices can be opened. That means it needs to be
before the devices are registered.
Fixes: 15bf722e6f6c0 ("cdc-acm: Add support of ATOL FPrint fiscal printers") Cc: stable <stable@kernel.org> Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20250717141259.2345605-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reports a use-after-free in comedi in the below link, which is
due to comedi gladly removing the allocated async area even though poll
requests are still active on the wait_queue_head inside of it. This can
cause a use-after-free when the poll entries are later triggered or
removed, as the memory for the wait_queue_head has been freed. We need
to check there are no tasks queued on any of the subdevices' wait queues
before allowing the device to be detached by the `COMEDI_DEVCONFIG`
ioctl.
Tasks will read-lock `dev->attach_lock` before adding themselves to the
subdevice wait queue, so fix the problem in the `COMEDI_DEVCONFIG` ioctl
handler by write-locking `dev->attach_lock` before checking that all of
the subdevices are safe to be deleted. This includes testing for any
sleepers on the subdevices' wait queues. It remains locked until the
device has been detached. This requires the `comedi_device_detach()`
function to be refactored slightly, moving the bulk of it into new
function `comedi_device_detach_locked()`.
Note that the refactor of `comedi_device_detach()` results in
`comedi_device_cancel_all()` now being called while `dev->attach_lock`
is write-locked, which wasn't the case previously, but that does not
matter.
Thanks to Jens Axboe for diagnosing the problem and co-developing this
patch.
The current power direction of an USB-C port also influences the
power_supply's online status, so a power role change should also update
the power_supply.
Fixes an issue on some systems where plugging in a normal USB device in
for the first time after a reboot will cause upower to erroneously
consider the system to be connected to AC power.
When a card is present in the reader, the driver currently defers
autosuspend by returning -EAGAIN during the suspend callback to
trigger USB remote wakeup signaling. However, this does not guarantee
that the mmc child device has been resumed, which may cause issues if
it remains suspended while the card is accessible.
This patch ensures that all child devices, including the mmc host
controller, are explicitly resumed before returning -EAGAIN. This
fixes a corner case introduced by earlier remote wakeup handling,
improving reliability of runtime PM when a card is inserted.
Fixes: 883a87ddf2f1 ("misc: rtsx_usb: Use USB remote wakeup signaling for card insertion detection") Cc: stable@vger.kernel.org Signed-off-by: Ricky Wu <ricky_wu@realtek.com> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Link: https://lore.kernel.org/r/20250711140143.2105224-1-ricky_wu@realtek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The grp->bb_largest_free_order is updated regardless of whether
mb_optimize_scan is enabled. This can lead to inconsistencies between
grp->bb_largest_free_order and the actual s_mb_largest_free_orders list
index when mb_optimize_scan is repeatedly enabled and disabled via remount.
For example, if mb_optimize_scan is initially enabled, largest free
order is 3, and the group is in s_mb_largest_free_orders[3]. Then,
mb_optimize_scan is disabled via remount, block allocations occur,
updating largest free order to 2. Finally, mb_optimize_scan is re-enabled
via remount, more block allocations update largest free order to 1.
At this point, the group would be removed from s_mb_largest_free_orders[3]
under the protection of s_mb_largest_free_orders_locks[2]. This lock
mismatch can lead to list corruption.
To fix this, whenever grp->bb_largest_free_order changes, we now always
attempt to remove the group from its old order list. However, we only
insert the group into the new order list if `mb_optimize_scan` is enabled.
This approach helps prevent lock inconsistencies and ensures the data in
the order lists remains reliable.
Fixes: 196e402adf2e ("ext4: improve cr 0 / cr 1 group scanning") CC: stable@vger.kernel.org Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Zhang Yi <yi.zhang@huawei.com> Link: https://patch.msgid.link/20250714130327.1830534-12-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Groups with no free blocks shouldn't be in any average fragment size list.
However, when all blocks in a group are allocated(i.e., bb_fragments or
bb_free is 0), we currently skip updating the average fragment size, which
means the group isn't removed from its previous s_mb_avg_fragment_size[old]
list.
This created "zombie" groups that were always skipped during traversal as
they couldn't satisfy any block allocation requests, negatively impacting
traversal efficiency.
Therefore, when a group becomes completely full, bb_avg_fragment_size_order
is now set to -1. If the old order was not -1, a removal operation is
performed; if the new order is not -1, an insertion is performed.
Fixes: 196e402adf2e ("ext4: improve cr 0 / cr 1 group scanning") CC: stable@vger.kernel.org Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Zhang Yi <yi.zhang@huawei.com> Link: https://patch.msgid.link/20250714130327.1830534-11-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When allocating IOVA the candidate range gets aligned to the target
alignment. If the range is close to ULONG_MAX then the ALIGN() can
wrap resulting in a corrupted iova.
Open code the ALIGN() using get_add_overflow() to prevent this.
This simplifies the checks as we don't need to check for length earlier
either.
Consolidate the two copies of this code under a single helper.
This bug would allow userspace to create a mapping that overlaps with some
other mapping or a reserved range.
Cc: stable@vger.kernel.org Fixes: 51fe6141f0f6 ("iommufd: Data structure to provide IOVA to PFN mapping") Reported-by: syzbot+c2f65e2801743ca64e08@syzkaller.appspotmail.com Closes: https://lore.kernel.org/r/685af644.a00a0220.2e5631.0094.GAE@google.com Reviewed-by: Yi Liu <yi.l.liu@intel.com> Reviewed-by: Nicolin Chen <nicolinc@nvidia.com> Link: https://patch.msgid.link/all/1-v1-7b4a16fc390b+10f4-iommufd_alloc_overflow_jgg@nvidia.com/ Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the SM6115 MDSS compatible to clients compatible list, as it also
needs that workaround.
Without this workaround, for example, QRB4210 RB2 which is based on
SM4250/SM6115 generates a lot of smmu unhandled context faults during
boot:
We now do a weighted selection of server interfaces when allocating
new channels. The weights are decided based on the speed advertised.
The fulfilled weight for an interface is a counter that is used to
track the interface selection. It should be reset back to zero once
all interfaces fulfilling their weight.
In cifs_chan_update_iface, this reset logic was missing. As a result
when the server interface list changes, the client may not be able
to find a new candidate for other channels after all interfaces have
been fulfilled.
Fixes: a6d8fb54a515 ("cifs: distribute channels across interfaces based on speed") Cc: <stable@vger.kernel.org> Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the regmap_write() for software reset in fsl_sai_config_disable would
cause the FSL_SAI_CSR_BCE bit to be cleared. Refer to
commit 197c53c8ecb34 ("ASoC: fsl_sai: Don't disable bitclock for i.MX8MP")
FSL_SAI_CSR_BCE should not be cleared. So need to use regmap_update_bits()
instead of regmap_write() for these bit operations.
Fixes: dc78f7e59169d ("ASoC: fsl_sai: Force a software reset when starting in consumer mode") Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Link: https://patch.msgid.link/20250807020318.2143219-1-shengjiu.wang@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In using CONFIG_RTC_HCTOSYS, rtc_hctosys() will sync the RTC time to the
kernel time as long as rtc_read_time() succeeds. In some power loss
situations, our supercapacitor-backed DS1342 RTC comes up with either an
unpredictable future time or the default 01/01/00 from the datasheet.
The oscillator stop flag (OSF) is set in these scenarios due to the
power loss and can be used to determine the validity of the RTC data.
Some chip types in the ds1307 driver already have OSF handling to
determine whether .read_time provides valid RTC data or returns -EINVAL.
This change removes the clear of the OSF in .probe as the OSF needs to
be preserved to expand the OSF handling to the ds1341 chip type (note
that DS1341 and DS1342 share a datasheet).
The error occurs on the third attempt to encode extents. When function
ext_tree_prepare_commit() reallocates a larger buffer to retry encoding
extents, the "layoutupdate_pages" page array is initialized only after the
retry loop. But ext_tree_free_commitdata() is called on every iteration
and tries to put pages in the array, thus dereferencing uninitialized
pointers.
An additional problem is that there is no limit on the maximum possible
buffer_size. When there are too many extents, the client may create a
layoutcommit that is larger than the maximum possible RPC size accepted
by the server.
During testing, we observed two typical scenarios. First, one memory page
for extents is enough when we work with small files, append data to the
end of the file, or preallocate extents before writing. But when we fill
a new large file without preallocating, the number of extents can be huge,
and counting the number of written extents in ext_tree_encode_commit()
does not help much. Since this number increases even more between
unlocking and locking of ext_tree, the reallocated buffer may not be
large enough again and again.
Co-developed-by: Konstantin Evtushenko <koevtushenko@yandex.com> Signed-off-by: Konstantin Evtushenko <koevtushenko@yandex.com> Signed-off-by: Sergey Bashirov <sergeybashirov@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20250630183537.196479-2-sergeybashirov@gmail.com Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When there are too many block extents for a layoutcommit, they may not
all fit into the maximum-sized RPC. This patch allows the generic pnfs
code to properly handle -ENOSPC returned by the block/scsi layout driver
and trigger additional layoutcommits if necessary.
Co-developed-by: Konstantin Evtushenko <koevtushenko@yandex.com> Signed-off-by: Konstantin Evtushenko <koevtushenko@yandex.com> Signed-off-by: Sergey Bashirov <sergeybashirov@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20250630183537.196479-5-sergeybashirov@gmail.com Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
At the end of the isect translation, disc_addr represents the physical
disk offset. Thus, end calculated from disk_addr is also a physical disk
offset. Therefore, range checking should be done using map->disk_offset,
not map->start.
Because of integer division, we need to carefully calculate the
disk offset. Consider the example below for a stripe of 6 volumes,
a chunk size of 4096, and an offset of 70000.
In blk_stack_limits(), we check that the t->chunk_sectors value is a
multiple of the t->physical_block_size value.
However, by finding the chunk_sectors value in bytes, we may overflow
the unsigned int which holds chunk_sectors, so change the check to be
based on sectors.
Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: John Garry <john.g.garry@oracle.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Link: https://lore.kernel.org/r/20250729091448.1691334-2-john.g.garry@oracle.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the LAN8710A datasheet (Rev. B, section 3.8.5.1), a hardware
reset is required after power-on, and the reference clock (REF_CLK) must be
established before asserting reset.
The source and destination of some strcpy operations was the same.
Split out the part of the operations that needed to be done for those
particular calls so the unnecessary copy wasn't done.
In case a menu has comment without letters/numbers (eg. characters
matching the regexp '^[^[:alpha:][:digit:]]+$', for example - or *),
hitting space will cycle through those comments, rather than
selecting/deselecting the currently-highlighted option.
This is the behaviour of hitting any letter/digit: jump to the next
option which prompt starts with that letter. The only letters that
do not behave as such are 'y' 'm' and 'n'. Prompts that start with
one of those three letters are instead matched on the first letter
that is not 'y', 'm' or 'n'.
Fix that by treating 'space' as we treat y/m/n, ie. as an action key,
not as shortcut to jump to prompt.
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr> Signed-off-by: Peter Korsgaard <peter@korsgaard.com> Signed-off-by: Cherniaev Andrei <dungeonlords789@naver.com>
[masahiro: took from Buildroot, adjusted the commit subject] Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The on_treeview2_cursor_changed() handler is connected to both the left
and right tree views, but it hardcodes model2 (the GtkTreeModel of the
right tree view). This is incorrect. Get the associated model from the
view.
During BMC firmware upgrades on live systems, the ipmi_msghandler
generates excessive "BMC returned incorrect response" warnings
while the BMC is temporarily offline. This can flood system logs
in large deployments.
Replace dev_warn() with dev_warn_ratelimited() to throttle these
warnings and prevent log spam during BMC maintenance operations.
MLX cap pg_track_log_max_msg_size consists of 5 bits, value of which is
used as power of 2 for max_msg_size. This can lead to multiplication
overflow between max_msg_size (u32) and integer constant, and afterwards
incorrect value is being written to rq_size.
Fix this issue by extending integer constant to u64 type.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
When PCI_IRQ_AFFINITY is set for calling pci_alloc_irq_vectors(), it
means interrupts are spread around the available CPUs. It also means that
the interrupts become managed, which means that an interrupt is shutdown
when all the CPUs in the interrupt affinity mask go offline.
Using managed interrupts in this way means that we should ensure that
completions should not occur on HW queues where the associated interrupt
is shutdown. This is typically achieved by ensuring only CPUs which are
online can generate IO completion traffic to the HW queue which they are
mapped to (so that they can also serve completion interrupts for that HW
queue).
The problem in the driver is that a CPU can generate completions to a HW
queue whose interrupt may be shutdown, as the CPUs in the HW queue
interrupt affinity mask may be offline. This can cause IOs to never
complete and hang the system. The driver maintains its own CPU <-> HW
queue mapping for submissions, see aac_fib_vector_assign(), but this does
not reflect the CPU <-> HW queue interrupt affinity mapping.
Commit 9dc704dcc09e ("scsi: aacraid: Reply queue mapping to CPUs based on
IRQ affinity") tried to remedy this issue may mapping CPUs properly to HW
queue interrupts. However this was later reverted in commit c5becf57dd56
("Revert "scsi: aacraid: Reply queue mapping to CPUs based on IRQ
affinity") - it seems that there were other reports of hangs. I guess
that this was due to some implementation issue in the original commit or
maybe a HW issue.
Fix the very original hang by just not using managed interrupts by not
setting PCI_IRQ_AFFINITY. In this way, all CPUs will be in each HW queue
affinity mask, so should not create completion problems if any CPUs go
offline.
Signed-off-by: John Garry <john.g.garry@oracle.com> Link: https://lore.kernel.org/r/20250715111535.499853-1-john.g.garry@oracle.com Closes: https://lore.kernel.org/linux-scsi/20250618192427.3845724-1-jmeneghi@redhat.com/ Reviewed-by: John Meneghini <jmeneghi@redhat.com> Tested-by: John Meneghini <jmeneghi@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix target_parse_pr_out_transport_id() to return a string representing
the transport ID in a human-readable format (e.g., naa.xxxxxxxx...) for
various SCSI protocol types (SAS, FCP, SRP, SBP).
Previously, the function returned a pointer to the raw binary buffer,
which was incorrectly compared against human-readable strings, causing
comparisons to fail. Now, the function writes a properly formatted
string into a buffer provided by the caller. The output format depends
on the transport protocol:
sas_user_scan() did not fully process wildcard channel scans
(SCAN_WILD_CARD) when a transport-specific user_scan() callback was
present. Only channel 0 would be scanned via user_scan(), while the
remaining channels were skipped, potentially missing devices.
user_scan() invokes updated sas_user_scan() for channel 0, and if
successful, iteratively scans remaining channels (1 to
shost->max_channel) via scsi_scan_host_selected(). This ensures complete
wildcard scanning without affecting transport-specific scanning behavior.
A large DMA mapping request can loop through dma address pinning for
many pages. In cases where THP can not be used, the repeated vmf_insert_pfn can
be costly, so let the task reschedule as need to prevent CPU stalls. Failure to
do so has potential harmful side effects, like increased memory pressure
as unrelated rcu tasks are unable to make their reclaim callbacks and
result in OOM conditions.
Signed-off-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Paul E. McKenney <paulmck@kernel.org> Link: https://lore.kernel.org/r/20250715184622.3561598-1-kbusch@meta.com Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
strcpy() performs no bounds checking and can lead to buffer overflows if
the input string exceeds the destination buffer size. This patch replaces
it with strncpy(), and null terminates the input string.
Let's return errors caught by the generic checks. This fixes generic/494 where
it expects to see EBUSY by setattr_prepare instead of EINVAL by f2fs for active
swapfile.
An infinite loop may occur if the following conditions occur due to
file system corruption.
(1) Condition for exfat_count_dir_entries() to loop infinitely.
- The cluster chain includes a loop.
- There is no UNUSED entry in the cluster chain.
(2) Condition for exfat_create_upcase_table() to loop infinitely.
- The cluster chain of the root directory includes a loop.
- There are no UNUSED entry and up-case table entry in the cluster
chain of the root directory.
(3) Condition for exfat_load_bitmap() to loop infinitely.
- The cluster chain of the root directory includes a loop.
- There are no UNUSED entry and bitmap entry in the cluster chain
of the root directory.
(4) Condition for exfat_find_dir_entry() to loop infinitely.
- The cluster chain includes a loop.
- The unused directory entries were exhausted by some operation.
(5) Condition for exfat_check_dir_empty() to loop infinitely.
- The cluster chain includes a loop.
- The unused directory entries were exhausted by some operation.
- All files and sub-directories under the directory are deleted.
This commit adds checks to break the above infinite loop.
This patch fixes an issue where the touchpad cursor movement becomes
slow on the Dell Precision 5560. Force the touchpad freq to 100khz
as a workaround.
Tested on Dell Precision 5560 with 6.14 to 6.14.6. Cursor movement
is now smooth and responsive.
Signed-off-by: fangzhong.zhou <myth5@myth5.com>
[wsa: kept sorting and removed unnecessary parts from commit msg] Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This follows the established practice and fixes a build failure for me:
security/apparmor/file.c: In function ‘__file_sock_perm’:
security/apparmor/file.c:544:24: error: unused variable ‘sock’ [-Werror=unused-variable]
544 | struct socket *sock = (struct socket *) file->private_data;
| ^~~~
Due to the semantics of iterate_devices(), the current code allows a
request-based dm table as long as it includes one request-stackable
device. It is supposed to only allow tables where there are no
non-request-stackable devices.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Reviewed-by: Mike Snitzer <snitzer@kernel.org> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
'I3C_BCR_HDR_CAP' is still spec v1.0 and has been renamed to 'advanced
capabilities' in v1.1 onwards. The ST pressure sensor LPS22DF does not
have HDR, but has the 'advanced cap' bit set. The core still wants to
get additional information using the CCC 'GETHDRCAP' (or GETCAPS in v1.1
onwards). Not all controllers support this CCC and will notify the upper
layers about it. For instantiating the device, we can ignore this
unsupported CCC as standard communication will work. Without this patch,
the device will not be instantiated at all.
When using AppArmor profiles inside an unprivileged container,
the link operation observes an unshifted ouid.
(tested with LXD and Incus)
For example, root inside container and uid 1000000 outside, with
`owner /root/link l,` profile entry for ln:
/root$ touch chain && ln chain link
==> dmesg
apparmor="DENIED" operation="link" class="file"
namespace="root//lxd-feet_<var-snap-lxd-common-lxd>" profile="linkit"
name="/root/link" pid=1655 comm="ln" requested_mask="l" denied_mask="l"
fsuid=1000000 ouid=0 [<== should be 1000000] target="/root/chain"
Fix by mapping inode uid of old_dentry in aa_path_link() rather than
using it directly, similarly to how it's mapped in __file_path_perm()
later in the file.
Signed-off-by: Gabriel Totev <gabriel.totev@zetier.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In using CONFIG_RTC_HCTOSYS, rtc_hctosys() will sync the RTC time to the
kernel time as long as rtc_read_time() succeeds. In some power loss
situations, our supercapacitor-backed DS1342 RTC comes up with either an
unpredictable future time or the default 01/01/00 from the datasheet.
The oscillator stop flag (OSF) is set in these scenarios due to the
power loss and can be used to determine the validity of the RTC data.
This change expands the oscillator stop flag (OSF) handling that has
already been implemented for some chips to the ds1341 chip (DS1341 and
DS1342 share a datasheet). This handling manages the validity of the RTC
data in .read_time and .set_time based on the OSF.
LKP found a random config which failed to build because IO accessors
were not defined:
In file included from drivers/i3c/master.c:21:
drivers/i3c/internals.h: In function 'i3c_writel_fifo':
>> drivers/i3c/internals.h:35:9: error: implicit declaration of function 'writesl' [-Werror=implicit-function-declaration]
Add the proper header to where the IO accessors are used.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202507150208.BZDzzJ5E-lkp@intel.com/ Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20250717120046.9022-2-wsa+renesas@sang-engineering.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Passing a module name longer than MODULE_NAME_LEN to the delete_module
syscall results in its silent truncation. This really isn't much of
a problem in practice, but it could theoretically lead to the removal of an
incorrect module. It is more sensible to return ENAMETOOLONG or ENOENT in
such a case.
Update the syscall to return ENOENT, as documented in the delete_module(2)
man page to mean "No module by that name exists." This is appropriate
because a module with a name longer than MODULE_NAME_LEN cannot be loaded
in the first place.
Fix Smatch-detected error:
drivers/md/dm-zoned-target.c:1073 dmz_iterate_devices()
error: uninitialized symbol 'r'.
Smatch detects a possible use of the uninitialized variable 'r' in
dmz_iterate_devices() because if dmz->nr_ddevs is zero, the loop is
skipped and 'r' is returned without being set, leading to undefined
behavior.
Initialize 'r' to 0 before the loop. This ensures that if there are no
devices to iterate over, the function still returns a defined value.
The sdw_dev_lock protects the SoundWire driver callbacks against
the probed flag, which is used to skip the callbacks if the
driver gets removed. For more information see commit bd29c00edd0a
("soundwire: revisit driver bind/unbind and callbacks").
However, this lock is a frequent source of mutex inversions.
Many audio operations eventually hit the hardware resulting in a
SoundWire callback, this means that typically the driver has the
locking order ALSA/ASoC locks -> sdw_dev_lock. Conversely, the IRQ
comes in directly from the SoundWire hardware, but then will often
want to access ALSA/ASoC, such as updating something in DAPM or
an ALSA control. This gives the other lock order sdw_dev_lock ->
ALSA/ASoC locks.
When the IRQ handling was initially added to SoundWire this was
through a callback mechanism. As such it required being covered by
the lock because the callbacks are part of the sdw_driver structure
and are thus present regardless of if the driver is currently
probed.
Since then a newer mechanism using the IRQ framework has been
added, which is currently covered by the same lock but this isn't
actually required. Handlers for the IRQ framework are registered in
probe and should by released during remove, thus the IRQ framework
will have already unbound the IRQ before the slave driver is
removed. Avoid the aforementioned mutex inversion by moving the
handle_nested_irq call outside of the sdw_dev_lock.
During pm_prepare callback, pm_request_resume() delays SoundWire manager D0
entry sequence. Synchronize runtime resume sequence for amd_manager
instance prior to invoking child devices resume sequence for both the amd
power modes(ClockStop Mode and Power off mode).
Change the power_mode_mask check and use pm_runtime_resume() in
amd_pm_prepare() callback.
In w7090p_tuner_write_serpar, msg is controlled by user. When msg[0].buf is null and msg[0].len is zero, former checks on msg[0].buf would be passed. If accessing msg[0].buf[2] without sanity check, null pointer deref would happen. We add
check on msg[0].len to prevent crash.
Similar commit: commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
In dib7090p_rw_on_apb, msg is controlled by user. When msg[0].buf is null and
msg[0].len is zero, former checks on msg[0].buf would be passed. If accessing
msg[0].buf[2] without sanity check, null pointer deref would happen. We add
check on msg[0].len to prevent crash. Similar issue occurs when access
msg[1].buf[0] and msg[1].buf[1].
Similar commit: commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
This driver passes the length of an i2c_msg directly to
usb_control_msg(). If the message is now a read and of length 0, it
violates the USB protocol and a warning will be printed. Enable the
I2C_AQ_NO_ZERO_LEN_READ quirk for this adapter thus forbidding 0-length
read messages altogether.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
The existing fixed value of 16 worked for UYVY 720P60 over
2 lanes at 594MHz, or UYVY 1080P60 over 4 lanes. (RGB888
1080P60 needs 6 lanes at 594MHz).
It doesn't allow for lower resolutions to work as the FIFO
underflows.
374 is required for 1080P24 or 1080P30 UYVY over 2 lanes @
972Mbit/s, but >374 means that the FIFO underflows on 1080P50
UYVY over 2 lanes @ 972Mbit/s.
Whilst it would be nice to compute it, the required information
isn't published by Toshiba.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
When calling tc358743_set_fmt, the code was calling tc358743_get_fmt
to choose a valid format. However that sets the colorspace
based on information read back from the chip, not the colour
format requested.
The result was that if you called try or set format for UYVY
when the current format was RGB3 then you would get told SRGB,
and try RGB3 when current was UYVY and you would get told
SMPTE170M.
The value programmed in the VI_REP register for the colorspace
is always set by this driver, therefore there is no need to read
back the value, and never set to REC709.
Return the colorspace based on the format set/tried instead.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
The probe for the TC358743 reads the CHIPID register from
the device and compares it to the expected value of 0.
If the I2C request fails then that also returns 0, so
the driver loads thinking that the device is there.
Generally I2C communications are reliable so there is
limited need to check the return value on every transfer,
therefore only amend the one read during probe to check
for I2C errors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
With the ATA error model, an NCQ command failure always triggers an abort
(termination) of all NCQ commands queued on the device. In such case, the
SAT or the host must handle the failed command according to the command
sense data and immediately retry all other NCQ commands that were aborted
due to the failed NCQ command.
For SAS HBAs controlled by the mpi3mr driver, NCQ command aborts are not
handled by the HBA SAT and sent back to the host, with an ioc log
information equal to 0x31080000 (IOC_LOGINFO_PREFIX_PL with the PL code
PL_LOGINFO_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR). The function
mpi3mr_process_op_reply_desc() always forces a retry of commands
terminated with the status MPI3_IOCSTATUS_SCSI_IOC_TERMINATED using the
SCSI result DID_SOFT_ERROR, regardless of the ioc_loginfo for the
command. This correctly forces the retry of collateral NCQ abort
commands, but with the retry counter for the command being incremented.
If a command to an ATA device is subject to too many retries due to other
NCQ commands failing (e.g. read commands trying to access unreadable
sectors), the collateral NCQ abort commands may be terminated with an
error as they run out of retries. This violates the SAT specification and
causes hard-to-debug command errors.
Solve this issue by modifying the handling of the
MPI3_IOCSTATUS_SCSI_IOC_TERMINATED status to check if a command is for an
ATA device and if the command ioc_loginfo indicates an NCQ collateral
abort. If that is the case, force the command retry using the SCSI result
DID_IMM_RETRY to avoid incrementing the command retry count.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Link: https://lore.kernel.org/r/20250606052747.742998-2-dlemoal@kernel.org Tested-by: Yafang Shao <laoar.shao@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
With the ATA error model, an NCQ command failure always triggers an abort
(termination) of all NCQ commands queued on the device. In such case, the
SAT or the host must handle the failed command according to the command
sense data and immediately retry all other NCQ commands that were aborted
due to the failed NCQ command.
For SAS HBAs controlled by the mpt3sas driver, NCQ command aborts are not
handled by the HBA SAT and sent back to the host, with an ioc log
information equal to 0x31080000 (IOC_LOGINFO_PREFIX_PL with the PL code
PL_LOGINFO_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR). The function
_scsih_io_done() always forces a retry of commands terminated with the
status MPI2_IOCSTATUS_SCSI_IOC_TERMINATED using the SCSI result
DID_SOFT_ERROR, regardless of the log_info for the command. This
correctly forces the retry of collateral NCQ abort commands, but with the
retry counter for the command being incremented. If a command to an ATA
device is subject to too many retries due to other NCQ commands failing
(e.g. read commands trying to access unreadable sectors), the collateral
NCQ abort commands may be terminated with an error as they run out of
retries. This violates the SAT specification and causes hard-to-debug
command errors.
Solve this issue by modifying the handling of the
MPI2_IOCSTATUS_SCSI_IOC_TERMINATED status to check if a command is for an
ATA device and if the command loginfo indicates an NCQ collateral
abort. If that is the case, force the command retry using the SCSI result
DID_IMM_RETRY to avoid incrementing the command retry count.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Link: https://lore.kernel.org/r/20250606052747.742998-3-dlemoal@kernel.org Tested-by: Yafang Shao <laoar.shao@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On some Dell XPS 13 (9345) variants, the battery used is lithium-polymer
based. Currently, this is reported as unknown technology due to the entry
missing.
[ 4083.135325] Unknown battery technology 'LIP'
Add another check for lithium-polymer in the technology parsing callback
and return that instead of unknown.
If a call to lpfc_sli4_read_rev() from lpfc_sli4_hba_setup() fails, the
resultant cleanup routine lpfc_sli4_vport_delete_fcp_xri_aborted() may
occur before sli4_hba.hdwqs are allocated. This may result in a null
pointer dereference when attempting to take the abts_io_buf_list_lock for
the first hardware queue. Fix by adding a null ptr check on
phba->sli4_hba.hdwq and early return because this situation means there
must have been an error during port initialization.
The function divides number of online CPUs by num_core_siblings, and
later checks the divider by zero. This implies a possibility to get
and divide-by-zero runtime error. Fix it by moving the check prior to
division. This also helps to save one indentation level.
DMA operates in Double Buffer Mode (DBM) when the transfer is cyclic and
there are at least two periods.
When DBM is enabled, the DMA toggles between two memory targets (SxM0AR and
SxM1AR), indicated by the SxSCR.CT bit (Current Target).
There is no need to update the next memory address if two periods are
configured, as SxM0AR and SxM1AR are already properly set up before the
transfer begins in the stm32_dma_start_transfer() function.
This avoids unnecessary updates to SxM0AR/SxM1AR, thereby preventing
potential Transfer Errors. Specifically, when the channel is enabled,
SxM0AR and SxM1AR can only be written if SxSCR.CT=1 and SxSCR.CT=0,
respectively. Otherwise, a Transfer Error interrupt is triggered, and the
stream is automatically disabled.
mc_subled used for multi_index needs well defined array indexes,
to guarantee the desired result, use reg for that.
If devicetree child nodes is processed in random or reverse order
you may end up with multi_index "blue green red" instead of the expected
"red green blue".
If user space apps uses multi_index to deduce how to control the leds
they would most likely be broken without this patch if devicetree
processing is reversed (which it appears to be).
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji.dts has reg set
but I don't see how it can have worked without this change.
If reg is not set, an error is returned,
If reg is out of range, an error is returned.
reg within led child nodes starts with 0, to map to the iout in each bank.
Signed-off-by: Johan Adolfsson <johan.adolfsson@axis.com> Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com> Link: https://lore.kernel.org/r/20250617-led-fix-v7-1-cdbe8efc88fa@axis.com Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When operating a pipeline with a missing V4L2_CID_LINK_FREQ control this
two line warning is printed each time the pipeline is started. Reduce
this excessive logging by only warning once for the missing control.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
request_mem_region() will return NULL instead of error code
when the memory request fails. Therefore, we should check if
the return value is non-zero instead of less than zero. In
this way, this patch also fixes the build warnings:
arch/mips/lantiq/falcon/sysctrl.c:214:50: error: ordered comparison of pointer with integer zero [-Werror=extra]
214 | res_status.name) < 0) ||
| ^
arch/mips/lantiq/falcon/sysctrl.c:216:47: error: ordered comparison of pointer with integer zero [-Werror=extra]
216 | res_ebu.name) < 0) ||
| ^
arch/mips/lantiq/falcon/sysctrl.c:219:50: error: ordered comparison of pointer with integer zero [-Werror=extra]
219 | res_sys[0].name) < 0) ||
| ^
arch/mips/lantiq/falcon/sysctrl.c:222:50: error: ordered comparison of pointer with integer zero [-Werror=extra]
222 | res_sys[1].name) < 0) ||
| ^
arch/mips/lantiq/falcon/sysctrl.c:225:50: error: ordered comparison of pointer with integer zero [-Werror=extra]
225 | res_sys[2].name) < 0))
|
Signed-off-by: Shiji Yang <yangshiji66@outlook.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Not all tasks have an ABI associated or vDSO mapped,
for example kthreads never do.
If such a task ever ends up calling stack_top(), it will derefence the
NULL ABI pointer and crash.
The intermediary value was included in the wrong
hash state. While there, adapt to user-space by
setting the timestamp to 0 if stuck and inserting
the values nevertheless.
Acked-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: Markus Theil <theil.markus@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When computing the tree index in dbAllocAG, we never check if we are
out of bounds realative to the size of the stree.
This could happen in a scenario where the filesystem metadata are
corrupted.
The reproducer builds a corrupted file on disk with a negative i_size value.
Add a check when opening this file to avoid subsequent operation failures.
Reported-by: syzbot+630f6d40b3ccabc8e96e@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=630f6d40b3ccabc8e96e Tested-by: syzbot+630f6d40b3ccabc8e96e@syzkaller.appspotmail.com Signed-off-by: Edward Adam Davis <eadavis@qq.com> Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The fileset value of the inode copy from the disk by the reproducer is
AGGR_RESERVED_I. When executing evict, its hard link number is 0, so its
inode pages are not truncated. This causes the bugon to be triggered when
executing clear_inode() because nrpages is greater than 0.
When the bfad_im_probe() function fails during initialization, the memory
pointed to by bfad->im is freed without setting bfad->im to NULL.
Subsequently, during driver uninstallation, when the state machine enters
the bfad_sm_stopping state and calls the bfad_im_probe_undo() function,
it attempts to free the memory pointed to by bfad->im again, thereby
triggering a double-free vulnerability.
The driver probes with the invalid timeout value when
'iTCO_wdt_set_timeout()' fails, as its return value is not checked. In
this case, when executing "wdctl", we may get:
The timeout value is the value of "heartbeat" or "WATCHDOG_TIMEOUT", and
the timeleft value is calculated from the register value we actually read
(0xffff) by masking with 0x3ff and converting ticks to seconds (* 6 / 10).
Add error handling to return the failure code if 'iTCO_wdt_set_timeout()'
fails, ensuring the driver probe fails and prevents invalid operation.
These functions are exported but their prototypes are not defined.
This patch adds the missing function prototypes to fix the following
compilation warnings:
arch/mips/kernel/vpe-mt.c:180:7: error: no previous prototype for 'vpe_alloc' [-Werror=missing-prototypes]
180 | void *vpe_alloc(void)
| ^~~~~~~~~
arch/mips/kernel/vpe-mt.c:198:5: error: no previous prototype for 'vpe_start' [-Werror=missing-prototypes]
198 | int vpe_start(void *vpe, unsigned long start)
| ^~~~~~~~~
arch/mips/kernel/vpe-mt.c:208:5: error: no previous prototype for 'vpe_stop' [-Werror=missing-prototypes]
208 | int vpe_stop(void *vpe)
| ^~~~~~~~
arch/mips/kernel/vpe-mt.c:229:5: error: no previous prototype for 'vpe_free' [-Werror=missing-prototypes]
229 | int vpe_free(void *vpe)
| ^~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
