There was a nouveau DDX that relied on legacy context ioctls to work,
but we fixed it years ago, give distros that have a modern DDX the
option to break the uAPI and close the mess of holes that legacy
context support is.
The context functions are not used by the i915 driver and should not
be used by modeset drivers. These driver functions contain several bugs
and security holes. This change makes these functions optional can be
turned on by a setting, they are turned off by default for modeset
driver with the exception of the nouvea driver that may require them with
an old version of libdrm.
Revert "drm: mark context support as a legacy subsystem"
v2: remove returns from void function, and formatting (Daniel Vetter)
v3:
- s/Nova/nouveau/ in the commit message, and add references to the
previous attempts
- drop the part touching the drm hw lock, that should be a separate
patch.
Signed-off-by: Peter Antoine <peter.antoine@intel.com> (v2) Cc: Peter Antoine <peter.antoine@intel.com> (v2) Reviewed-by: Peter Antoine <peter.antoine@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: move DRM_VM dependency into legacy config.
v3: fix missing dep (kbuild robot)
Cc: stable@vger.kernel.org Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some machines have an lvds child device in vbt even though a panel is
not attached. To make detection more reliable we now also check the lvds
config bits available in the vbt.
Async update callbacks are expected to set the old_fb in the new_state
so prepare/cleanup framebuffers are balanced.
Calling drm_atomic_set_fb_for_plane() (which gets a reference of the new
fb and put the old fb) is not required, as it's taken care by
drm_mode_cursor_universal() when calling drm_atomic_helper_update_plane().
Cc: <stable@vger.kernel.org> # v4.19+ Fixes: 539c320bfa97 ("drm/vc4: update cursors asynchronously through atomic") Suggested-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Helen Koike <helen.koike@collabora.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190603165610.24614-5-helen.koike@collabora.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case of async update, modifications are done in place, i.e. in the
current plane state, so the new_state is prepared and the new_state is
cleaned up (instead of the old_state, unlike what happens in a
normal sync update).
To cleanup the old_fb properly, it needs to be placed in the new_state
in the end of async_update, so cleanup call will unreference the old_fb
correctly.
if (plane->state->fb && plane->state->fb != new_state->fb) {
...
}
Which was wrong, as the fb were just assigned to be equal, so this if
statement nevers evaluates to true.
Another details is that the function drm_crtc_vblank_get() can only be
called when vop->is_enabled is true, otherwise it has no effect and
trows a WARN_ON().
Calling drm_atomic_set_fb_for_plane() (which get a referent of the new
fb and pus the old fb) is not required, as it is taken care by
drm_mode_cursor_universal() when calling
drm_atomic_helper_update_plane().
Fixes: 15609559a834 ("drm/rockchip: update cursors asynchronously through atomic.") Cc: <stable@vger.kernel.org> # v4.20+ Signed-off-by: Helen Koike <helen.koike@collabora.com> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190603165610.24614-2-helen.koike@collabora.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The limit here is supposed to be how much of the page is left, but it's
just using PAGE_SIZE as the limit.
The other thing to remember is that snprintf() returns the number of
bytes which would have been copied if we had had enough room. So that
means that if we run out of space then this code would end up passing a
negative value as the limit and the kernel would print an error message.
I have change the code to use scnprintf() which returns the number of
bytes that were successfully printed (not counting the NUL terminator).
The first thing is that the "m->size + (...)" addition could overflow,
and the second is that round_up() overflows to zero if the result is
within PAGE_SIZE of the type max.
In this code, the "m->size" variable is an u64 but we're saving the
result in "map_size" which is an unsigned long and genwqe_user_vmap()
takes an unsigned long as well. So I have used ULONG_MAX as the upper
bound. From a practical perspective unsigned long is fine/better than
trying to change all the types to u64.
Fixes: eaf4722d4645 ("GenWQE Character device and DDCB queue") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pistachio platform uses the U-Boot bootloader & generally boots a
kernel in the uImage format. As such it's useful to build one when
building the kernel, but to do so currently requires the user to
manually specify a uImage target on the make command line.
Make uImage.gz the pistachio platform's default build target, so that
the default is to build a kernel image that we can actually boot on a
board such as the MIPS Creator Ci40.
Marked for stable backport as far as v4.1 where pistachio support was
introduced. This is primarily useful for CI systems such as kernelci.org
which will benefit from us building a suitable image which can then be
booted as part of automated testing, extending our test coverage to the
affected stable branches.
Signed-off-by: Paul Burton <paul.burton@mips.com> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com>
URL: https://groups.io/g/kernelci/message/388 Cc: stable@vger.kernel.org # v4.1+ Cc: linux-mips@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The virt_addr_valid() function is meant to return true iff
virt_to_page() will return a valid struct page reference. This is true
iff the address provided is found within the unmapped address range
between PAGE_OFFSET & MAP_BASE, but we don't currently check for that
condition. Instead we simply mask the address to obtain what will be a
physical address if the virtual address is indeed in the desired range,
shift it to form a PFN & then call pfn_valid(). This can incorrectly
return true if called with a virtual address which, after masking,
happens to form a physical address corresponding to a valid PFN.
For example we may vmalloc an address in the kernel mapped region
starting a MAP_BASE & obtain the virtual address:
addr = 0xc000000000002000
When masked by virt_to_phys(), which uses __pa() & in turn CPHYSADDR(),
we obtain the following (bogus) physical address:
addr = 0x2000
In a common system with PHYS_OFFSET=0 this will correspond to a valid
struct page which should really be accessed by virtual address
PAGE_OFFSET+0x2000, causing virt_addr_valid() to incorrectly return 1
indicating that the original address corresponds to a struct page.
This is equivalent to the ARM64 change made in commit ca219452c6b8
("arm64: Correctly bounds check virt_addr_valid").
This fixes fallout when hardened usercopy is enabled caused by the
related commit 517e1fbeb65f ("mm/usercopy: Drop extra
is_vmalloc_or_module() check") which removed a check for the vmalloc
range that was present from the introduction of the hardened usercopy
feature.
Signed-off-by: Paul Burton <paul.burton@mips.com>
References: ca219452c6b8 ("arm64: Correctly bounds check virt_addr_valid")
References: 517e1fbeb65f ("mm/usercopy: Drop extra is_vmalloc_or_module() check") Reported-by: Julien Cristau <jcristau@debian.org> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Tested-by: YunQiang Su <ysu@wavecomp.com>
URL: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=929366 Cc: stable@vger.kernel.org # v4.12+ Cc: linux-mips@vger.kernel.org Cc: Yunqiang Su <ysu@wavecomp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the controller supports less queues than requested, we
should make sure that queue mapping does the right thing and
not assume that all queues are available. This fixes a crash
when the controller supports less queues than requested.
The rules are:
1. if no write/poll queues are requested, we assign the available queues
to the default queue map. The default and read queue maps share the
existing queues.
2. if write queues are requested:
- first make sure that read queue map gets the requested
nr_io_queues count
- then grant the default queue map the minimum between the requested
nr_write_queues and the remaining queues. If there are no available
queues to dedicate to the default queue map, fallback to (1) and
share all the queues in the existing queue map.
3. if poll queues are requested:
- map the remaining queues to the poll queue map.
Also, provide a log indication on how we constructed the different
queue maps.
Reported-by: Harris, James R <james.r.harris@intel.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Tested-by: Jim Harris <james.r.harris@intel.com> Cc: <stable@vger.kernel.org> # v5.0+ Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0aaba41b58bc ("s390: remove all code using the access register
mode") removed access register mode from the kernel, and also from the
address space detection logic. However, user space could still switch
to access register mode (trans_exc_code == 1), and exceptions in that
mode would not be correctly assigned.
Fix this by adding a check for trans_exc_code == 1 to get_fault_type(),
and remove the wrong comment line before that function.
Fixes: 0aaba41b58bc ("s390: remove all code using the access register mode") Reviewed-by: Janosch Frank <frankja@linux.ibm.com> Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: <stable@vger.kernel.org> # v4.15+ Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver does not support reading more than 255 bytes at once because
the register for storing the number of bytes to read is only 8 bits. Add
a max_read_len quirk to enforce this.
This was found when using this driver with the SFP driver, which was
previously reading all 256 bytes in the SFP EEPROM in one transaction.
This caused a bunch of hard-to-debug errors in the xiic driver since the
driver/logic was treating the number of bytes to read as zero.
Rejecting transactions that aren't supported at least allows the problem
to be diagnosed more easily.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_desc() computes a pointer into the LDT while holding a lock that
protects the LDT from being freed, but then drops the lock and returns the
(now potentially dangling) pointer to its caller.
Fix it by giving the caller a copy of the LDT entry instead.
Fixes: 670f928ba09b ("x86/insn-eval: Add utility function to get segment descriptor") Cc: stable@vger.kernel.org Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
0cc3cd21657b ("cpu/hotplug: Boot HT siblings at least once")
we always, no matter what, have to bring up x86 HT siblings during boot at
least once in order to avoid first MCE bringing the system to its knees.
That means that whenever 'nosmt' is supplied on the kernel command-line,
all the HT siblings are as a result sitting in mwait or cpudile after
going through the online-offline cycle at least once.
This causes a serious issue though when a kernel, which saw 'nosmt' on its
commandline, is going to perform resume from hibernation: if the resume
from the hibernated image is successful, cr3 is flipped in order to point
to the address space of the kernel that is being resumed, which in turn
means that all the HT siblings are all of a sudden mwaiting on address
which is no longer valid.
That results in triple fault shortly after cr3 is switched, and machine
reboots.
Fix this by always waking up all the SMT siblings before initiating the
'restore from hibernation' process; this guarantees that all the HT
siblings will be properly carried over to the resumed kernel waiting in
resume_play_dead(), and acted upon accordingly afterwards, based on the
target kernel configuration.
Symmetricaly, the resumed kernel has to push the SMT siblings to mwait
again in case it has SMT disabled; this means it has to online all
the siblings when resuming (so that they come out of hlt) and offline
them again to let them reach mwait.
Cc: 4.19+ <stable@vger.kernel.org> # v4.19+ Debugged-by: Thomas Gleixner <tglx@linutronix.de> Fixes: 0cc3cd21657b ("cpu/hotplug: Boot HT siblings at least once") Signed-off-by: Jiri Kosina <jkosina@suse.cz> Acked-by: Pavel Machek <pavel@ucw.cz> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
check_scc_error() checks SCC_RVSREQ.RVSERR bit. RVSERR detects a
correction error in the next (up or down) delay tap position. However,
since the command is successful, only retuning needs to be executed.
This has been confirmed by HW engineers.
Thus, on SCC error, set retuning flag instead of setting an error code.
We accidentally changed the error code from -EAGAIN to 1 when we did the
blk-mq conversion.
Maybe a contributing factor to this mistake is that it wasn't obvious
that the "while (chunk) {" condition is always true. I have cleaned
that up as well.
Fixes: d0be12274dad ("mspro_block: convert to blk-mq") Cc: stable@vger.kernel.org Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To print the pathname that will be used by shell in the current
environment, 'command -v' is a standardized way. [1]
'which' is also often used in scripts, but it is less portable.
When I worked on commit bd55f96fa9fc ("kbuild: refactor cc-cross-prefix
implementation"), I was eager to use 'command -v' but it did not work.
(The reason is explained below.)
I kept 'which' as before but got rid of '> /dev/null 2>&1' as I
thought it was no longer needed. Sorry, I was wrong.
It works well on my Ubuntu machine, but Alexey Brodkin reports noisy
warnings on CentOS7 when 'which' fails to find the given command in
the PATH environment.
$ which foo
which: no foo in (/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin)
Given that behavior of 'which' depends on system (and it may not be
installed by default), I want to try 'command -v' once again.
The specification [1] clearly describes the behavior of 'command -v'
when the given command is not found:
Otherwise, no output shall be written and the exit status shall reflect
that the name was not found.
However, we need a little magic to use 'command -v' from Make.
$(shell ...) passes the argument to a subshell for execution, and
returns the standard output of the command.
Here is a trick. GNU Make may optimize this by executing the command
directly instead of forking a subshell, if no shell special characters
are found in the command and omitting the subshell will not change the
behavior.
In this case, no shell special character is used. So, Make will try
to run it directly. However, 'command' is a shell-builtin command,
then Make would fail to find it in the PATH environment:
$ make ARCH=m68k defconfig
make: command: Command not found
make: command: Command not found
make: command: Command not found
In fact, Make has a table of shell-builtin commands because it must
ask the shell to execute them.
Until recently, 'command' was missing in the table.
This issue was fixed by the following commit:
| commit 1af314465e5dfe3e8baa839a32a72e83c04f26ef
| Author: Paul Smith <psmith@gnu.org>
| Date: Sun Nov 12 18:10:28 2017 -0500
|
| * job.c: Add "command" as a known shell built-in.
|
| This is not a POSIX shell built-in but it's common in UNIX shells.
| Reported by Nick Bowler <nbowler@draconx.ca>.
Because the latest release is GNU Make 4.2.1 in 2016, this commit is
not included in any released versions. (But some distributions may
have back-ported it.)
We need to trick Make to spawn a subshell. There are various ways to
do so:
1) Use a shell special character '~' as dummy
$(shell : ~; command -v $(c)gcc)
2) Use a variable reference that always expands to the empty string
(suggested by David Laight)
$(shell command$${x:+} -v $(c)gcc)
3) Use redirect
$(shell command -v $(c)gcc 2>/dev/null)
I chose 3) to not confuse people. The stderr would not be polluted
anyway, but it will provide extra safety, and is easy to understand.
The ram pstore backend has always had the crash dumper frontend enabled
unconditionally. However, it was possible to effectively disable it
by setting a record_size=0. All the machinery would run (storing dumps
to the temporary crash buffer), but 0 bytes would ultimately get stored
due to there being no przs allocated for dumps. Commit 89d328f637b9
("pstore/ram: Correctly calculate usable PRZ bytes"), however, assumed
that there would always be at least one allocated dprz for calculating
the size of the temporary crash buffer. This was, of course, not the
case when record_size=0, and would lead to a NULL deref trying to find
the dprz buffer size:
BUG: unable to handle kernel NULL pointer dereference at (null)
...
IP: ramoops_probe+0x285/0x37e (fs/pstore/ram.c:808)
cxt->pstore.bufsize = cxt->dprzs[0]->buffer_size;
Instead, we need to only enable the frontends based on the success of the
prz initialization and only take the needed actions when those zones are
available. (This also fixes a possible error in detecting if the ftrace
frontend should be enabled.)
Set tfm to NULL on free_buf_for_compression() after crypto_free_comp().
This avoid a use-after-free when allocate_buf_for_compression()
and free_buf_for_compression() are called twice. Although
free_buf_for_compression() freed the tfm, allocate_buf_for_compression()
won't reinitialize the tfm since the tfm pointer is not NULL.
When a waiter is waked by CB_NOTIFY_LOCK, it will retry
nfs4_proc_setlk(). The waiter may fail to nfs4_proc_setlk() and sleep
again. However, the waiter is already removed from clp->cl_lock_waitq
when handling CB_NOTIFY_LOCK in nfs4_wake_lock_waiter(). So any
subsequent CB_NOTIFY_LOCK won't wake this waiter anymore. We should
put the waiter back to clp->cl_lock_waitq before retrying.
Cc: stable@vger.kernel.org #4.9+ Signed-off-by: Yihao Wu <wuyihao@linux.alibaba.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b7dbcc0e433f "NFSv4.1: Fix a race where CB_NOTIFY_LOCK fails to wake a waiter"
found this bug. However it didn't fix it.
This commit replaces schedule_timeout() with wait_woken() and
default_wake_function() with woken_wake_function() in function
nfs4_retry_setlk() and nfs4_wake_lock_waiter(). wait_woken() uses
memory barriers in its implementation to avoid potential race condition
when putting a process into sleeping state and then waking it up.
Fixes: a1d617d8f134 ("nfs: allow blocking locks to be awoken by lock callbacks") Cc: stable@vger.kernel.org #4.9+ Signed-off-by: Yihao Wu <wuyihao@linux.alibaba.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The addition of rpc_check_timeout() to call_decode causes an Oops
when the RPCSEC_GSS credential is rejected.
The reason is that rpc_decode_header() will call xprt_release() in
order to free task->tk_rqstp, which is needed by rpc_check_timeout()
to check whether or not we should exit due to a soft timeout.
The fix is to move the call to xprt_release() into call_decode() so
we can perform it after rpc_check_timeout().
Reported-by: Olga Kornievskaia <olga.kornievskaia@gmail.com> Reported-by: Nick Bowler <nbowler@draconx.ca> Fixes: cea57789e408 ("SUNRPC: Clean up") Cc: stable@vger.kernel.org # v5.1+ Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If call_status returns ENOTCONN, we need to re-establish the connection
state after. Otherwise the client goes into an infinite loop of call_encode,
call_transmit, call_status (ENOTCONN), call_encode.
Fixes: c8485e4d63 ("SUNRPC: Handle ECONNREFUSED correctly in xprt_transmit()") Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Cc: stable@vger.kernel.org # v2.6.29+ Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the found documentation, data cache flushes and sync
instructions are needed on the PCX-U+ (PA8200, e.g. C200/C240)
platforms, while PCX-W (PA8500, e.g. C360) platforms aparently don't
need those flushes when changing the IO PDIR data structures.
We have no documentation for PCX-W+ (PA8600) and PCX-W2 (PA8700) CPUs,
but Carlo Pisani reported that his C3600 machine (PA8600, PCX-W+) fails
when the fdc instructions were removed. His firmware didn't set the NIOP
bit, so one may assume it's a firmware bug since other C3750 machines
had the bit set.
Even if documentation (as mentioned above) states that PCX-W (PA8500,
e.g. J5000) does not need fdc flushes, Sven could show that an Adaptec
29320A PCI-X SCSI controller reliably failed on a dd command during the
first five minutes in his J5000 when fdc flushes were missing.
Going forward, we will now NOT replace the fdc and sync assembler
instructions by NOPS if:
a) the NP iopdir_fdc bit was set by firmware, or
b) we find a CPU up to and including a PCX-W+ (PA8600).
This fixes the HPMC crashes on a C240 and C36XX machines. For other
machines we rely on the firmware to set the bit when needed.
In case one finds HPMC issues, people could try to boot their machines
with the "no-alternatives" kernel option to turn off any alternative
patching.
Reported-by: Sven Schnelle <svens@stackframe.org> Reported-by: Carlo Pisani <carlojpisani@gmail.com> Tested-by: Sven Schnelle <svens@stackframe.org> Fixes: 3847dab77421 ("parisc: Add alternative coding infrastructure") Signed-off-by: Helge Deller <deller@gmx.de> Cc: stable@vger.kernel.org # 5.0+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only support I/O to kernel space. Using %sr1 to load the coherence
index may be racy unless interrupts are disabled. This patch changes the
code used to load the coherence index to use implicit space register
selection. This saves one instruction and eliminates the race.
Tested on rp3440, c8000 and c3750.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Cc: stable@vger.kernel.org Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of today if userspace process tries to access a kernel virtual addres
(0x7000_0000 to 0x7ffff_ffff) such that a legit kernel mapping already
exists, that process hangs instead of being killed with SIGSEGV
Fix that by ensuring that do_page_fault() handles kenrel vaddr only if
in kernel mode.
And given this, we can also simplify the code a bit. Now a vmalloc fault
implies kernel mode so its failure (for some reason) can reuse the
@no_context label and we can remove @bad_area_nosemaphore.
This fixes multiple things in the habanalabs debugfs code, in particular:
- mmu_write() was unnecessarily verbose, copying around between multiple
buffers
- mmu_write() could write a user-specified, unbounded amount of userspace
memory into a kernel buffer (out-of-bounds write)
- multiple debugfs read handlers ignored the user-supplied count,
potentially corrupting out-of-bounds userspace data
- hl_device_read() was unnecessarily verbose
- hl_device_write() could read uninitialized stack memory
- multiple debugfs read handlers copied terminating null characters to
userspace
Herbert Xu pointed out that commit bb73c52bad36 ("rcu: Don't disable
preemption for Tiny and Tree RCU readers") was incorrect in making the
preempt_disable/enable() be conditional on CONFIG_PREEMPT_COUNT.
If CONFIG_PREEMPT_COUNT isn't enabled, the preemption enable/disable is
a no-op, but still is a compiler barrier.
And RCU locking still _needs_ that compiler barrier.
It is simply fundamentally not true that RCU locking would be a complete
no-op: we still need to guarantee (for example) that things that can
trap and cause preemption cannot migrate into the RCU locked region.
The way we do that is by making it a barrier.
See for example commit 386afc91144b ("spinlocks and preemption points
need to be at least compiler barriers") from back in 2013 that had
similar issues with spinlocks that become no-ops on UP: they must still
constrain the compiler from moving other operations into the critical
region.
Now, it is true that a lot of RCU operations already use READ_ONCE() and
WRITE_ONCE() (which in practice likely would never be re-ordered wrt
anything remotely interesting), but it is also true that that is not
globally the case, and that it's not even necessarily always possible
(ie bitfields etc).
Reported-by: Herbert Xu <herbert@gondor.apana.org.au> Fixes: bb73c52bad36 ("rcu: Don't disable preemption for Tiny and Tree RCU readers") Cc: stable@kernel.org Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 38030d7cb779 ("net/tls: avoid NULL-deref on resync during device removal")
tried to fix a potential NULL-dereference by taking the
context rwsem. Unfortunately the RX resync may get called
from soft IRQ, so we can't use the rwsem to protect from
the device disappearing. Because we are guaranteed there
can be only one resync at a time (it's called from strparser)
use a bit to indicate resync is busy and make device
removal wait for the bit to get cleared.
Note that there is a leftover "flags" field in struct
tls_context already.
Fixes: 4799ac81e52a ("tls: Add rx inline crypto offload") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
e is the counter used to save the location of a dump when an
skb is filled. Once the walk of the table is complete, mr_table_dump
needs to return without resetting that index to 0. Dump of a specific
table is looping because of the reset because there is no way to
indicate the walk of the table is done.
Move the reset to the caller so the dump of each table starts at 0,
but the loop counter is maintained if a dump fills an skb.
Fixes: e1cedae1ba6b0 ("ipmr: Refactor mr_rtm_dumproute") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a matchall classifier is added, there is a small time interval in
which tp->root is NULL. If we receive a packet in this small time slice
a NULL pointer dereference will happen, leading to a kernel panic:
Fix this by adding a NULL check in mall_classify().
Fixes: ed76f5edccc9 ("net: sched: protect filter_chain list with filter_chain_lock mutex") Signed-off-by: Matteo Croce <mcroce@redhat.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cd9ff4de0107 changed the key for IFF_POINTOPOINT devices to
INADDR_ANY but neigh_xmit which is used for MPLS encapsulations was not
updated to use the altered key. The result is that every packet Tx does
a lookup on the gateway address which does not find an entry, a new one
is created only to find the existing one in the table right before the
insert since arp_constructor was updated to reset the primary key. This
is seen in the allocs and destroys counters:
ip -s -4 ntable show | head -10 | grep alloc
which increase for each packet showing the unnecessary overhread.
Fix by having neigh_xmit use __ipv4_neigh_lookup_noref for NEIGH_ARP_TABLE.
Fixes: cd9ff4de0107 ("ipv4: Make neigh lookup keys for loopback/point-to-point devices be INADDR_ANY") Reported-by: Alan Maguire <alan.maguire@oracle.com> Signed-off-by: David Ahern <dsahern@gmail.com> Tested-by: Alan Maguire <alan.maguire@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian and Alan both reported seeing overflows after upgrades to 5.x kernels:
neighbour: arp_cache: neighbor table overflow!
Alan's mpls script helped get to the bottom of this bug. When a new entry
is created the gc_entries counter is bumped in neigh_alloc to check if a
new one is allowed to be created. ___neigh_create then searches for an
existing entry before inserting the just allocated one. If an entry
already exists, the new one is dropped in favor of the existing one. In
this case the cleanup path needs to drop the gc_entries counter. There
is no memory leak, only a counter leak.
Fixes: 58956317c8d ("neighbor: Improve garbage collection") Reported-by: Ian Kumlien <ian.kumlien@gmail.com> Reported-by: Alan Maguire <alan.maguire@oracle.com> Signed-off-by: David Ahern <dsahern@gmail.com> Tested-by: Alan Maguire <alan.maguire@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WoL magic packet configuration sometimes does not work due to
couple of leakages found.
Mainly there was a regression introduced during readx_poll refactoring.
Next, fw request waiting time was too small. Sometimes that
caused sleep proxy config function to return with an error
and to skip WoL configuration.
At last, WoL data were passed to FW from not clean buffer.
That could cause FW to accept garbage as a random configuration data.
Fixes: 6a7f2277313b ("net: aquantia: replace AQ_HW_WAIT_FOR with readx_poll_timeout_atomic") Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IPv4 equivalent code works. A workaround is to use IPPROTO_RAW
instead of IPPROTO_ICMPV6.
The failure happens because 2 bytes are eaten from the msghdr by
rawv6_probe_proto_opt() starting from commit 19e3c66b52ca ("ipv6
equivalent of "ipv4: Avoid reading user iov twice after
raw_probe_proto_opt""), but at that time it was not a problem because
IPV6_HDRINCL was not yet introduced.
Only eat these 2 bytes if hdrincl == 0.
Fixes: 715f504b1189 ("ipv6: add IPV6_HDRINCL option for raw sockets") Signed-off-by: Olivier Matz <olivier.matz@6wind.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As it was done in commit 8f659a03a0ba ("net: ipv4: fix for a race
condition in raw_sendmsg") and commit 20b50d79974e ("net: ipv4: emulate
READ_ONCE() on ->hdrincl bit-field in raw_sendmsg()") for ipv4, copy the
value of inet->hdrincl in a local variable, to avoid introducing a race
condition in the next commit.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default, packets received in another VRF should not be passed to an
unbound socket in the default VRF. This patch updates the IPv4 UDP
multicast logic to match the unicast VRF logic (in compute_score()),
as well as the IPv6 mcast logic (in __udp_v6_is_mcast_sock()).
The particular case I noticed was DHCP discover packets going
to the 255.255.255.255 address, which are handled by
__udp4_lib_mcast_deliver(). The previous code meant that running
multiple different DHCP server or relay agent instances across VRFs
did not work correctly - any server/relay agent in the default VRF
received DHCP discover packets for all other VRFs.
Fixes: 6da5b0f027a8 ("net: ensure unbound datagram socket to be chosen when not in a VRF") Signed-off-by: Tim Beale <timbeale@catalyst.net.nz> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nathan reported the new behaviour breaks Android, as Android just add
new rules and delete old ones.
If we return 0 without adding dup rules, Android will remove the new
added rules and causing system to soft-reboot.
Fixes: e9919a24d302 ("fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied") Reported-by: Nathan Chancellor <natechancellor@gmail.com> Reported-by: Yaro Slav <yaro330@gmail.com> Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Tested-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the process issuing a "start" command on the pktgen procfs
interface, acquires the pktgen thread lock and never release it, until
all pktgen threads are completed. The above can blocks indefinitely any
other pktgen command and any (even unrelated) netdevice removal - as
the pktgen netdev notifier acquires the same lock.
The issue is demonstrated by the following script, reported by Matteo:
ip -b - <<'EOF'
link add type dummy
link add type veth
link set dummy0 up
EOF
modprobe pktgen
echo reset >/proc/net/pktgen/pgctrl
{
echo rem_device_all
echo add_device dummy0
} >/proc/net/pktgen/kpktgend_0
echo count 0 >/proc/net/pktgen/dummy0
echo start >/proc/net/pktgen/pgctrl &
sleep 1
rmmod veth
Fix the above releasing the thread lock around the sleep call.
Additionally we must prevent racing with forcefull rmmod - as the
thread lock no more protects from them. Instead, acquire a self-reference
before waiting for any thread. As a side effect, running
rmmod pktgen
while some thread is running now fails with "module in use" error,
before this patch such command hanged indefinitely.
Note: the issue predates the commit reported in the fixes tag, but
this fix can't be applied before the mentioned commit.
v1 -> v2:
- no need to check for thread existence after flipping the lock,
pktgen threads are freed only at net exit time
-
Fixes: 6146e6a43b35 ("[PKTGEN]: Removes thread_{un,}lock() macros.") Reported-and-tested-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rollover used to use a complex RCU mechanism for assignment, which had
a race condition. The below patch fixed the bug and greatly simplified
the logic.
The feature depends on fanout, but the state is private to the socket.
Fanout_release returns f only when the last member leaves and the
fanout struct is to be freed.
Destroy rollover unconditionally, regardless of fanout state.
Fixes: 57f015f5eccf2 ("packet: fix crash in fanout_demux_rollover()") Reported-by: syzbot <syzkaller@googlegroups.com> Diagnosed-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SFP modules do not like reads longer than 16 bytes, so read the
EEPROM in chunks of 16 bytes at a time. This behaviour is not specified
in the SFP MSAs, which specifies:
"The serial interface uses the 2-wire serial CMOS E2PROM protocol
defined for the ATMEL AT24C01A/02/04 family of components."
and
"As long as the SFP+ receives an acknowledge, it shall serially clock
out sequential data words. The sequence is terminated when the host
responds with a NACK and a STOP instead of an acknowledge."
We must avoid breaking a read across a 16-bit quantity in the diagnostic
page, thankfully all 16-bit quantities in that page are naturally
aligned.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"
Starting up....
tsks tx/s rx/s tx+rx K/s mbi K/s mbo K/s tx us/c rtt us cpu
%
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
"
>From vmcore, we can find that clean_list is NULL.
>From the source code, rds_mr_flushd calls rds_ib_mr_pool_flush_worker.
Then rds_ib_mr_pool_flush_worker calls
"
rds_ib_flush_mr_pool(pool, 0, NULL);
"
Then in function
"
int rds_ib_flush_mr_pool(struct rds_ib_mr_pool *pool,
int free_all, struct rds_ib_mr **ibmr_ret)
"
ibmr_ret is NULL.
In the source code,
"
...
list_to_llist_nodes(pool, &unmap_list, &clean_nodes, &clean_tail);
if (ibmr_ret)
*ibmr_ret = llist_entry(clean_nodes, struct rds_ib_mr, llnode);
/* more than one entry in llist nodes */
if (clean_nodes->next)
llist_add_batch(clean_nodes->next, clean_tail, &pool->clean_list);
...
"
When ibmr_ret is NULL, llist_entry is not executed. clean_nodes->next
instead of clean_nodes is added in clean_list.
So clean_nodes is discarded. It can not be used again.
The workqueue is executed periodically. So more and more clean_nodes are
discarded. Finally the clean_list is NULL.
Then this problem will occur.
Fixes: 1bc144b62524 ("net, rds, Replace xlist in net/rds/xlist.h with llist") Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix ability to set RX descriptor number, the reason - initially
"tx_max_pending" was set incorrectly, but the issue appears after
adding sanity check, so fix is for "sanity" patch.
Fixes: 37e2d99b59c476 ("ethtool: Ensure new ring parameters are within bounds during SRINGPARAM") Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Jianlin's testing, netperf was broken with 'Connection reset by peer',
as the cookie check failed in rt6_check() and ip6_dst_check() always
returned NULL.
It's caused by Commit 93531c674315 ("net/ipv6: separate handling of FIB
entries from dst based routes"), where the cookie can be got only when
'c1'(see below) for setting dst_cookie whereas rt6_check() is called
when !'c1' for checking dst_cookie, as we can see in ip6_dst_check().
Since in ip6_dst_check() both rt6_dst_from_check() (c1) and rt6_check()
(!c1) will check the 'from' cookie, this patch is to remove the c1 check
in rt6_get_cookie(), so that the dst_cookie can always be set properly.
Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes") Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If rp1 bc_forwarding is set while rp2 bc_forwarding is not, after
doing "ping 192.168.200.255" on h1, then ping 192.168.200.255 on
h2, and the packets can still be forwared.
This issue was caused by the input route cache. It should only do
the cache for either bc forwarding or local delivery. Otherwise,
local delivery can use the route cache for bc forwarding of other
interfaces.
This patch is to fix it by not doing cache for local delivery if
all.bc_forwarding is enabled.
Note that we don't fix it by checking route cache local flag after
rt_cache_valid() in "local_input:" and "ip_mkroute_input", as the
common route code shouldn't be touched for bc_forwarding.
Fixes: 5cbf777cfdf6 ("route: add support for directed broadcast forwarding") Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem was that the peer.cookie value points to an skb allocated
area on the first pass through this function, at which point it is
overwritten with a heap allocated value, but in certain cases, where a
COOKIE_ECHO chunk is included in the packet, a second pass through
sctp_process_init is made, where the cookie value is re-allocated,
leaking the first allocation.
Fix is to always allocate the cookie value, and free it when we are done
using it.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: syzbot+f7e9153b037eac9b1df8@syzkaller.appspotmail.com CC: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> CC: "David S. Miller" <davem@davemloft.net> CC: netdev@vger.kernel.org Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ethtool_get_regs() allocates a buffer of size ops->get_regs_len(),
and pass it to the kernel driver via ops->get_regs() for filling.
There is no restriction about what the kernel drivers can or cannot do
with the open ethtool_regs structure. They usually set regs->version
and ignore regs->len or set it to the same size as ops->get_regs_len().
But if userspace allocates a smaller buffer for the registers dump,
we would cause a userspace buffer overflow in the final copy_to_user()
call, which uses the regs.len value potentially reset by the driver.
To fix this, make this case obvious and store regs.len before calling
ops->get_regs(), to only copy as much data as requested by userspace,
up to the value returned by ops->get_regs_len().
While at it, remove the redundant check for non-null regbuf.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The logic for freeing an imported buffer with a virtual address is
broken. It will free the buffer instead of unmapping the dma buf.
Fix by reversing the if ladder and first check if the buffer is imported.
If userspace doesn't enable universal planes, then we automatically
add the primary and cursor planes. But for universal userspace there's
no such check (and maybe we only want to give the lessee one plane,
maybe not even the primary one), hence we need to check for the
implied plane.
As explained by Robin Murphy:
> the IOMMU shutdown disables paging, so if the VOP is still
> scanning out then that will result in whatever IOVAs it was using now going
> straight out onto the bus as physical addresses.
We had a more radical approach before in commit 7f3ef5dedb14 ("drm/rockchip: Allow driver to be shutdown on reboot/kexec")
but that resulted in new warnings and oopses on shutdown on rk3399
chromeos devices.
So second try is resurrecting Vicentes shutdown change which should
achieve the same result but in a less drastic way.
Fixes: 63238173b2fa ("Revert "drm/rockchip: Allow driver to be shutdown on reboot/kexec"") Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Brian Norris <briannorris@chromium.org> Cc: Doug Anderson <dianders@chromium.org> Cc: stable@vger.kernel.org Suggested-by: JeffyChen <jeffy.chen@rock-chips.com> Suggested-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Vicente Bergas <vicencb@gmail.com>
[adapted commit message to explain the history] Signed-off-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Brian Norris <briannorris@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190402113753.10118-1-heiko@sntech.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need this to make sure lessees can only connect their
plane/connectors to crtc objects they own. And note that this is
irrespective of whether the lessor is atomic or not, lessor cannot
prevent lessees from enabling atomic.
Hotplug can happen while drm_fbdev_generic_setup() is running so move
drm_client_add() call after setup is done to avoid
drm_fbdev_client_hotplug() running in two threads at the same time.
Fixes: 9060d7f49376 ("drm/fb-helper: Finish the generic fbdev emulation") Cc: stable@vger.kernel.org Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20190401141358.25309-1-noralf@tronnes.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current buffer check halves the frame rate on non-plus i.MX6Q,
as the IDMAC current buffer pointer is not yet updated when
ipu_plane_atomic_update_pending is called from the EOF irq handler.
Fixes: 70e8a0c71e9 ("drm/imx: ipuv3-plane: add function to query atomic update status") Tested-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code initializes HDMI PHY clock driver before reset line is
deasserted and clocks enabled. Because of that, initial readout of
clock divider is incorrect (0 instead of 2). This causes any clock
rate with divider 1 (register value 0) to be set incorrectly.
Fix this by moving initialization of HDMI PHY clock driver after reset
line is deasserted and clocks enabled.
Cc: stable@vger.kernel.org # 4.17+ Fixes: 4f86e81748fe ("drm/sun4i: Add support for H3 HDMI PHY variant") Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190514204337.11068-2-jernej.skrabec@siol.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In compat mode, we allowed host-backed user-space with guest-backed
kernel / device. In this mode, set shader commands was broken since
no relocations were emitted. Fix this.
Cc: <stable@vger.kernel.org> Fixes: e8c66efbfe3a ("drm/vmwgfx: Make user resource lookups reference-free during validation") Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Brian Paul <brianp@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
User-space handles equal to zero are interpreted as uninitialized or
illegal by some drm systems (most notably kms). This means that a
dumb buffer or surface with a zero user-space handle can never be
used as a kms frame-buffer.
Cc: <stable@vger.kernel.org> Fixes: c7eae62666ad ("drm/vmwgfx: Make the object handles idr-generated") Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Deepak Rawat <drawat@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The allocated pages need to be invalidated in CPU caches. On ARM32 the
DMA_BIDIRECTIONAL flag only ensures that data is written-back to DRAM and
the data stays in CPU cache lines. While the DMA_FROM_DEVICE flag ensures
that the corresponding CPU cache lines are getting invalidated and nothing
more, that's exactly what is needed for a newly allocated pages.
This fixes randomly failing rendercheck tests on Tegra30 using the
Opentegra driver for tests that use small-sized pixmaps (10x10 and less,
i.e. 1-2 memory pages) because apparently CPU reads out stale data from
caches and/or that data is getting evicted to DRAM at the time of HW job
execution.
The gcc-common.h file did not take into account certain macros that
might have already been defined in the build environment. This updates
the header to avoid redefining the macros, as seen on a Darwin host
using gcc 4.9.2:
HOSTCXX -fPIC scripts/gcc-plugins/arm_ssp_per_task_plugin.o - due to: scripts/gcc-plugins/gcc-common.h
In file included from scripts/gcc-plugins/arm_ssp_per_task_plugin.c:3:0:
scripts/gcc-plugins/gcc-common.h:153:0: warning: "__unused" redefined
^
In file included from /usr/include/stdio.h:64:0,
from /Users/hns/Documents/Projects/QuantumSTEP/System/Library/Frameworks/System.framework/Versions-jessie/x86_64-apple-darwin15.0.0/gcc/arm-linux-gnueabi/bin/../lib/gcc/arm-linux-gnueabi/4.9.2/plugin/include/system.h:40,
from /Users/hns/Documents/Projects/QuantumSTEP/System/Library/Frameworks/System.framework/Versions-jessie/x86_64-apple-darwin15.0.0/gcc/arm-linux-gnueabi/bin/../lib/gcc/arm-linux-gnueabi/4.9.2/plugin/include/gcc-plugin.h:28,
from /Users/hns/Documents/Projects/QuantumSTEP/System/Library/Frameworks/System.framework/Versions-jessie/x86_64-apple-darwin15.0.0/gcc/arm-linux-gnueabi/bin/../lib/gcc/arm-linux-gnueabi/4.9.2/plugin/include/plugin.h:23,
from scripts/gcc-plugins/gcc-common.h:9,
from scripts/gcc-plugins/arm_ssp_per_task_plugin.c:3:
/usr/include/sys/cdefs.h:161:0: note: this is the location of the previous definition
^
This reverts most of commit b8eee0e90f97 ("lockd: Show pid of lockd for
remote locks"), which caused remote locks to not be differentiated between
remote processes for NLM.
We retain the fixup for setting the client's fl_pid to a negative value.
Fixes: b8eee0e90f97 ("lockd: Show pid of lockd for remote locks") Cc: stable@vger.kernel.org Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Reviewed-by: XueWei Zhang <xueweiz@google.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cifs_read_allocate_pages, in case of ENOMEM, we go through
whole rdata->pages array but we have failed the allocation before
nr_pages, therefore we may end up calling put_page with NULL
pointer, causing oops
Signed-off-by: Roberto Bergantinos Corpas <rbergant@redhat.com> Acked-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently in the case where SMB2_ioctl returns the -EOPNOTSUPP error
there is a memory leak of pneg_inbuf. Fix this by returning via
the out_free_inbuf exit path that will perform the relevant kfree.
Addresses-Coverity: ("Resource leak") Fixes: 969ae8e8d4ee ("cifs: Accept validate negotiate if server return NT_STATUS_NOT_SUPPORTED") CC: Stable <stable@vger.kernel.org> # v5.1+ Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e895f00a8496 ("Staging: wlan-ng: hfa384x_usb.c Fixed too long
code line warnings.") moved the retrieval of the transfer buffer from
the URB from the top of function hfa384x_usbin_callback to a point
after reposting of the URB via a call to submit_rx_urb. The reposting
of the URB allocates a new transfer buffer so the new buffer is
retrieved instead of the buffer containing the response passed into
the callback. This results in failure to initialize the adapter with
an error reported in the system log (something like "CTLX[1] error:
state(Request failed)").
This change moves the retrieval to just before the point where the URB
is reposted so that the correct transfer buffer is retrieved and
initialization of the device succeeds.
Signed-off-by: Tim Collier <osdevtc@gmail.com> Fixes: e895f00a8496 ("Staging: wlan-ng: hfa384x_usb.c Fixed too long code line warnings.") Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The create_pagelist() "count" parameter comes from the user in
vchiq_ioctl() and it could overflow. If you look at how create_page()
is called in vchiq_prepare_bulk_data(), then the "size" variable is an
int so it doesn't make sense to allow negatives or larger than INT_MAX.
I don't know this code terribly well, but I believe that typical values
of "count" are typically quite low and I don't think this check will
affect normal valid uses at all.
The "pagelist_size" calculation can also overflow on 32 bit systems, but
not on 64 bit systems. I have added an integer overflow check for that
as well.
The Raspberry PI doesn't offer the same level of memory protection that
x86 does so these sorts of bugs are probably not super critical to fix.
As noted in commit 84b40e3b57ee ("serial: 8250: omap: Disable DMA for
console UART"), UART console lines use low-level PIO only access functions
which will conflict with use of the line when DMA is enabled, e.g. when
the console line is also used for systemd messages. So disable DMA
support for UART console lines.
Reported-by: Michael Rodin <mrodin@de.adit-jv.com> Link: https://patchwork.kernel.org/patch/10929511/ Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: stable@vger.kernel.org Signed-off-by: George G. Davis <george_davis@mentor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After memory allocation failure vc_allocate() doesn't clean up data
which has been initialized in visual_init(). In case of fbcon this
leads to divide-by-0 in fbcon_init() on next open of the same tty.
memory allocation in vc_allocate() may fail here:
1097: vc->vc_screenbuf = kzalloc(vc->vc_screenbuf_size, GFP_KERNEL);
on next open() fbcon_init() skips vc_font.data initialization:
1088: if (!p->fontdata) {
division by zero in fbcon_init() happens here:
1149: new_cols /= vc->vc_font.width;
Additional check is needed in fbcon_deinit() to prevent
usage of uninitialized vc_screenbuf:
1251: if (vc->vc_hi_font_mask && vc->vc_screenbuf)
1252: set_vc_hi_font(vc, false);
This patch prevents memory access beyond the evm_tfm array by checking the
validity of the index (hash algorithm) passed to init_desc(). The hash
algorithm can be arbitrarily set if the security.ima xattr type is not
EVM_XATTR_HMAC.
Recent versions of sphinx will emit messages like:
Documentation/sphinx/kerneldoc.py:103:
RemovedInSphinx20Warning: app.warning() is now deprecated.
Use sphinx.util.logging instead.
Switch to sphinx.util.logging to make this unsightly message go away.
Alas, that interface was only added in version 1.6, so we have to add a
version check to keep things working with older sphinxes.
Cc: stable@vger.kernel.org Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AutoReporter is going away; recent versions of sphinx emit a warning like:
Documentation/sphinx/kerneldoc.py:125:
RemovedInSphinx20Warning: AutodocReporter is now deprecated.
Use sphinx.util.docutils.switch_source_input() instead.
Make the switch. But switch_source_input() only showed up in 1.7, so we
have to do ugly version checks to keep things working in older versions.
Cc: stable@vger.kernel.org Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our version check in Documentation/conf.py never envisioned a world where
Sphinx moved beyond 1.x. Now that the unthinkable has happened, fix our
version check to handle higher version numbers correctly.
Cc: stable@vger.kernel.org Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following commit 4378a7d4be30 ("arm64: implement syscall wrappers"), the
syscall function names gained the '__arm64_' prefix. Ensure that we
have the correct #define for redirecting a default syscall through a
wrapper.
When we have holes in a normal memory zone, we could endup having
cached_migrate_pfns which may not necessarily be valid, under heavy memory
pressure with swapping enabled ( via __reset_isolation_suitable(),
triggered by kswapd).
Later if we fail to find a page via fast_isolate_freepages(), we may end
up using the migrate_pfn we started the search with, as valid page. This
could lead to accessing NULL pointer derefernces like below, due to an
invalid mem_section pointer.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008 [47/1825]
Mem abort info:
ESR = 0x96000004
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp = 0000000082f94ae9
[0000000000000008] pgd=0000000000000000
Internal error: Oops: 96000004 [#1] SMP
...
CPU: 10 PID: 6080 Comm: qemu-system-aar Not tainted 510-rc1+ #6
Hardware name: AmpereComputing(R) OSPREY EV-883832-X3-0001/OSPREY, BIOS 4819 09/25/2018
pstate: 60000005 (nZCv daif -PAN -UAO)
pc : set_pfnblock_flags_mask+0x58/0xe8
lr : compaction_alloc+0x300/0x950
[...]
Process qemu-system-aar (pid: 6080, stack limit = 0x0000000095070da5)
Call trace:
set_pfnblock_flags_mask+0x58/0xe8
compaction_alloc+0x300/0x950
migrate_pages+0x1a4/0xbb0
compact_zone+0x750/0xde8
compact_zone_order+0xd8/0x118
try_to_compact_pages+0xb4/0x290
__alloc_pages_direct_compact+0x84/0x1e0
__alloc_pages_nodemask+0x5e0/0xe18
alloc_pages_vma+0x1cc/0x210
do_huge_pmd_anonymous_page+0x108/0x7c8
__handle_mm_fault+0xdd4/0x1190
handle_mm_fault+0x114/0x1c0
__get_user_pages+0x198/0x3c0
get_user_pages_unlocked+0xb4/0x1d8
__gfn_to_pfn_memslot+0x12c/0x3b8
gfn_to_pfn_prot+0x4c/0x60
kvm_handle_guest_abort+0x4b0/0xcd8
handle_exit+0x140/0x1b8
kvm_arch_vcpu_ioctl_run+0x260/0x768
kvm_vcpu_ioctl+0x490/0x898
do_vfs_ioctl+0xc4/0x898
ksys_ioctl+0x8c/0xa0
__arm64_sys_ioctl+0x28/0x38
el0_svc_common+0x74/0x118
el0_svc_handler+0x38/0x78
el0_svc+0x8/0xc
Code: f8607840f100001f8b0114019a801020 (f9400400)
---[ end trace af6a35219325a9b6 ]---
The issue was reported on an arm64 server with 128GB with holes in the
zone (e.g, [32GB@4GB, 96GB@544GB]), with a swap device enabled, while
running 100 KVM guest instances.
This patch fixes the issue by ensuring that the page belongs to a valid
PFN when we fallback to using the lower limit of the scan range upon
failure in fast_isolate_freepages().
Link: http://lkml.kernel.org/r/1558711908-15688-1-git-send-email-suzuki.poulose@arm.com Fixes: 5a811889de10f1eb ("mm, compaction: use free lists to quickly locate a migration target") Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Reported-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Mel Gorman <mgorman@techsingularity.net> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Qian Cai <cai@lca.pw> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I don't think this is userspace visible but SIGKILL does not have
any si_codes that use the fault member of the siginfo union. Correct
this the simple way and call force_sig instead of force_sig_fault when
the signal is SIGKILL.
The two know places where synchronous SIGKILL are generated are
do_bad_area and fpsimd_save. The call paths to force_sig_fault are:
do_bad_area
arm64_force_sig_fault
force_sig_fault
force_signal_inject
arm64_notify_die
arm64_force_sig_fault
force_sig_fault
Which means correcting this in arm64_force_sig_fault is enough
to ensure the arm64 code is not misusing the generic code, which
could lead to maintenance problems later.
Cc: stable@vger.kernel.org Cc: Dave Martin <Dave.Martin@arm.com> Cc: James Morse <james.morse@arm.com> Cc: Will Deacon <will.deacon@arm.com> Fixes: af40ff687bc9 ("arm64: signal: Ensure si_code is valid for all fault signals") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the fixes commit, removing SIGKILL from each thread signal mask and
executing "goto fatal" directly will skip the call to
"trace_signal_deliver". At this point, the delivery tracking of the
SIGKILL signal will be inaccurate.
Therefore, we need to add trace_signal_deliver before "goto fatal" after
executing sigdelset.
Note: SEND_SIG_NOINFO matches the fact that SIGKILL doesn't have any info.
Link: http://lkml.kernel.org/r/20190425025812.91424-1-weizhenliang@huawei.com Fixes: cf43a757fd4944 ("signal: Restore the stop PTRACE_EVENT_EXIT") Signed-off-by: Zhenliang Wei <weizhenliang@huawei.com> Reviewed-by: Christian Brauner <christian@brauner.io> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Ivan Delalande <colona@arista.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Deepa Dinamani <deepa.kernel@gmail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building with -Wuninitialized and CONFIG_KASAN_SW_TAGS unset, Clang
warns:
mm/kasan/common.c:484:40: warning: variable 'tag' is uninitialized when
used here [-Wuninitialized]
kasan_unpoison_shadow(set_tag(object, tag), size);
^~~
set_tag ignores tag in this configuration but clang doesn't realize it at
this point in its pipeline, as it points to arch_kasan_set_tag as being
the point where it is used, which will later be expanded to (void
*)(object) without a use of tag. Initialize tag to 0xff, as it removes
this warning and doesn't change the meaning of the code.
We have a single node system with node 0 disabled:
Scanning NUMA topology in Northbridge 24
Number of physical nodes 2
Skipping disabled node 0
Node 1 MemBase 0000000000000000 Limit 00000000fbff0000
NODE_DATA(1) allocated [mem 0xfbfda000-0xfbfeffff]
This causes crashes in memcg when system boots:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
#PF error: [normal kernel read fault]
...
RIP: 0010:list_lru_add+0x94/0x170
...
Call Trace:
d_lru_add+0x44/0x50
dput.part.34+0xfc/0x110
__fput+0x108/0x230
task_work_run+0x9f/0xc0
exit_to_usermode_loop+0xf5/0x100
It is reproducible as far as 4.12. I did not try older kernels. You have
to have a new enough systemd, e.g. 241 (the reason is unknown -- was not
investigated). Cannot be reproduced with systemd 234.
The system crashes because the size of lru array is never updated in
memcg_update_all_list_lrus and the reads are past the zero-sized array,
causing dereferences of random memory.
The root cause are list_lru_memcg_aware checks in the list_lru code. The
test in list_lru_memcg_aware is broken: it assumes node 0 is always
present, but it is not true on some systems as can be seen above.
So fix this by avoiding checks on node 0. Remember the memcg-awareness by
a bool flag in struct list_lru.
Link: http://lkml.kernel.org/r/20190522091940.3615-1-jslaby@suse.cz Fixes: 60d3fd32a7a9 ("list_lru: introduce per-memcg lists") Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Michal Hocko <mhocko@suse.com> Suggested-by: Vladimir Davydov <vdavydov.dev@gmail.com> Acked-by: Vladimir Davydov <vdavydov.dev@gmail.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
memory.stat and other files already consider subtrees in their output, and
we should too in order to not present an inconsistent interface.
The current situation is fairly confusing, because people interacting with
cgroups expect hierarchical behaviour in the vein of memory.stat,
cgroup.events, and other files. For example, this causes confusion when
debugging reclaim events under low, as currently these always read "0" at
non-leaf memcg nodes, which frequently causes people to misdiagnose breach
behaviour. The same confusion applies to other counters in this file when
debugging issues.
Aggregation is done at write time instead of at read-time since these
counters aren't hot (unlike memory.stat which is per-page, so it does it
at read time), and it makes sense to bundle this with the file
notifications.
After this patch, events are propagated up the hierarchy:
[root@ktst ~]# cat /sys/fs/cgroup/system.slice/memory.events
low 0
high 0
max 0
oom 0
oom_kill 0
[root@ktst ~]# systemd-run -p MemoryMax=1 true
Running as unit: run-r251162a189fb4562b9dabfdc9b0422f5.service
[root@ktst ~]# cat /sys/fs/cgroup/system.slice/memory.events
low 0
high 0
max 7
oom 1
oom_kill 1
As this is a change in behaviour, this can be reverted to the old
behaviour by mounting with the `memory_localevents' flag set. However, we
use the new behaviour by default as there's a lack of evidence that there
are any current users of memory.events that would find this change
undesirable.
akpm: this is a behaviour change, so Cc:stable. THis is so that
forthcoming distros which use cgroup v2 are more likely to pick up the
revised behaviour.
Link: http://lkml.kernel.org/r/20190208224419.GA24772@chrisdown.name Signed-off-by: Chris Down <chris@chrisdown.name> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Shakeel Butt <shakeelb@google.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Tejun Heo <tj@kernel.org> Cc: Roman Gushchin <guro@fb.com> Cc: Dennis Zhou <dennis@kernel.org> Cc: Suren Baghdasaryan <surenb@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bit 4: ClockEnSet the ClockEn bit high to enable an external clocking
(crystal or clock generator at XIN). Set the ClockEn bit to 0 to disable
clocking
Bit 1: CrystalEnSet the CrystalEn bit high to enable the crystal
oscillator. When using an external clock source at XIN, CrystalEn must
be set low.
The bit 4, MAX310X_CLKSRC_EXTCLK_BIT, should be set and was not.
This was required to make the MAX3107 with an external crystal on our
board able to send or receive data.
When the tty layer requests the uart to throttle, the current code
executing in msm_serial will trigger "Bad mode in Error Handler" and
generate an invalid stack frame in pstore before rebooting (that is if
pstore is indeed configured: otherwise the user shall just notice a
reboot with no further information dumped to the console).
This patch replaces the PIO byte accessor with the word accessor
already used in PIO mode.
Fix wrong order in probing routine initialization - field `base_addr'
is used before it's initialized. Move assignment of 'priv->base_addr`
to the beginning, prior the call to mlxcpld_i2c_read_comm().
Wrong order caused the first read of capability register to be executed
at wrong offset 0x0 instead of 0x2000. By chance it was a "good
garbage" at 0x0 offset.
Fixes: 313ce648b5a4 ("i2c: mlxcpld: Add support for extended transaction length for i2c-mlxcpld") Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For a while, we've had the problem of i2c bus access not grabbing
a runtime PM ref when it's being used in userspace by i2c-dev, resulting
in nouveau spamming the kernel log with errors if anything attempts to
access the i2c bus while the GPU is in runtime suspend. An example:
[ 130.078386] nouveau 0000:01:00.0: i2c: aux 000d: begin idle timeout ffffffff
Since the GPU is in runtime suspend, the MMIO region that the i2c bus is
on isn't accessible. On x86, the standard behavior for accessing an
unavailable MMIO region is to just return ~0.
Except, that turned out to be a lie. While computers with a clean
concious will return ~0 in this scenario, some machines will actually
completely hang a CPU on certian bad MMIO accesses. This was witnessed
with someone's Lenovo ThinkPad P50, where sensors-detect attempting to
access the i2c bus while the GPU was suspended would result in a CPU
hang:
Yikes! While I wanted to try to make it so that accessing an i2c bus on
nouveau would wake up the GPU as needed, airlied pointed out that pretty
much any usecase for userspace accessing an i2c bus on a GPU (mainly for
the DDC brightness control that some displays have) is going to only be
useful while there's at least one display enabled on the GPU anyway, and
the GPU never sleeps while there's displays running.
Since teaching the i2c bus to wake up the GPU on userspace accesses is a
good deal more difficult than it might seem, mostly due to the fact that
we have to use the i2c bus during runtime resume of the GPU, we instead
opt for the easiest solution: don't let userspace access i2c busses on
the GPU at all while it's in runtime suspend.
Changes since v1:
* Also disable i2c busses that run over DP AUX
Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KVM_CAP_MAX_VCPU_ID is currently always reporting KVM_MAX_VCPU_ID on all
architectures. However, on s390x, the amount of usable CPUs is determined
during runtime - it is depending on the features of the machine the code
is running on. Since we are using the vcpu_id as an index into the SCA
structures that are defined by the hardware (see e.g. the sca_add_vcpu()
function), it is not only the amount of CPUs that is limited by the hard-
ware, but also the range of IDs that we can use.
Thus KVM_CAP_MAX_VCPU_ID must be determined during runtime on s390x, too.
So the handling of KVM_CAP_MAX_VCPU_ID has to be moved from the common
code into the architecture specific code, and on s390x we have to return
the same value here as for KVM_CAP_MAX_VCPUS.
This problem has been discovered with the kvm_create_max_vcpus selftest.
With this change applied, the selftest now passes on s390x, too.
Reviewed-by: Andrew Jones <drjones@redhat.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Reviewed-by: David Hildenbrand <david@redhat.com> Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190523164309.13345-9-thuth@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We met another Acer Aspire laptop which has the problem on the
headset-mic, the Pin 0x19 is not set the corret configuration for a
mic and the pin presence can't be detected too after plugging a
headset. Kailang suggested that we should set the coeff to enable the
mic and apply the ALC269_FIXUP_LIFEBOOK_EXTMIC. After doing that,
both headset-mic presence and headset-mic work well.
The existing ALC255_FIXUP_ACER_MIC_NO_PRESENCE set the headset-mic
jack to be a phantom jack. Now since the jack can support presence
unsol event, let us imporve it to set the jack to be a normal jack.
https://bugs.launchpad.net/bugs/1821269 Fixes: 5824ce8de7b1c ("ALSA: hda/realtek - Add support for Acer Aspire E5-475 headset mic") Cc: Chris Chiu <chiu@endlessm.com> CC: Daniel Drake <drake@endlessm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Kailang Yang <kailang@realtek.com> Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
