The code setting XP watchpoint comparator and mask registers should, in
order to be fully compliant with specification, zero one or more most
significant bits of each field. In both L cases it means zeroing bit 63.
The bitmask doing this was wrong, though, zeroing bit 60 instead.
Fortunately, due to a lucky coincidence, this turned out to be fairly
innocent with the existing hardware.
Fuzzing the CCN perf driver revealed a small but definitely dangerous
mistake in the event setup code. When a cycle counter is requested, the
driver should not reconfigure the events bus at all, otherwise it will
corrupt (in most but the simplest cases) its configuration and may end
up accessing XP array out of its bounds and corrupting control
registers.
Reported-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Tested-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Pawel Moll <pawel.moll@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "Miscellaneous Node" fell through cracks of node initialisation,
as its ID is shared with HN-I.
This patch treats MN as a special case (which it is), adding separate
validation check for it and pre-defining the node ID in relevant events
descriptions. That way one can simply run:
# perf stat -a -e ccn/mn_ecbarrier/ <workload>
Additionally, direction in the MN pseudo-events XP watchpoint
definitions is corrected to be "TX" (1) as they are defined from the
crosspoint point of view (thus barriers are transmitted from XP to MN).
The STiH4{07,10} platform contains some interconnect clocks which are used
by various IPs. If these clocks aren't handled correctly by ST's SDHCI
driver MMC will break and the following output can be observed:
The gpmc ranges property for NAND at CS0 was being overridden by later
includes that defined gpmc ethernet nodes, effectively breaking NAND on
these systems:
omap-gpmc 6e000000.gpmc: /ocp/gpmc@6e000000/nand@0,0 has
malformed 'reg' property
Instead of redefining the NAND range in every such dtsi, define all
currently used ranges in omap3-overo-base.dtsi.
Fixes: 98ce6007efb4 ("ARM: dts: overo: Support PoP NAND") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gpmc ranges property for NAND at CS0 has been broken since it was
first added.
This currently prevents the nand gpmc child node from being probed:
omap-gpmc 6e000000.gpmc: /ocp/gpmc@6e000000/nand@0,0 has
malformed 'reg' property
and consequently the NAND device from being registered.
Fixes: 98ce6007efb4 ("ARM: dts: overo: Support PoP NAND") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the ports as seen from the rear number as:
eth0 sfp lan5 lan4 lan3 lan2 lan1 lan6
which is illogical - this came about because the rev 2.0 boards have the
LEDs on the front for the DSA switch (lan5-1) reversed. Rev 2.1 boards
fixed the LED issue, and the Clearfog case numbers the lan ports
increasing from left to right.
Maintaining this illogical numbering causes confusion, with reports that
"my link isn't coming up" and "my connection negotiates 10base-Half"
both of which are due to people thinking that the port next to the SFP
is lan1.
Fix this by renumbering the ports to match people's expectations.
[gregory.clement@free-electrons.com: added the Fixes and stable tags]
Fixes: 4c945e8556ec ("ARM: dts: Add SolidRun Armada 388 Clearfog A1 DT
file") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 833f2cbf7091 ("ARM: dts: imx6: change the core clock of spdif")
changed many more clocks than only the SPDIF core clock as stated in
the commit message.
The MLB clock has been added and this causes SPDIF regression as
reported by Xavi Drudis Ferran and also in this forum post:
https://forum.digikey.com/thread/34240
The MX6Q Reference Manual does not mention that MLB is a clock related
to SPDIF, so change it back to a dummy clock to restore SPDIF
functionality.
Thanks to Ambika for providing the fix at:
https://community.nxp.com/thread/387131
While converting PCIe node on kirkwood by using label, the following
commit eb13cf8345e9 ("ARM: dts: kirkwood: Fixup pcie DT warnings")
introduced a regression on the OpenRD boards: the PCIe didn't work
anymore. As reported by Aaro Koskinen, the display/framebuffer was
lost. This commit adds the forgotten label.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Fixes: eb13cf8345e9 ("ARM: dts: kirkwood: Fixup pcie DT warnings") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 148c274ea644 ("ARM: kirkwood: ib62x0: add u-boot environment
partition") split the "u-boot" partition into "u-boot" and "u-boot
environment". However, instead of the size of the environment, an offset
was given, resulting in overlapping partitions.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com> Fixes: 148c274ea644 ("ARM: kirkwood: ib62x0: add u-boot environment partition") Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory Clement <gregory.clement@free-electrons.com> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: Luka Perkov <luka@openwrt.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i.MX6SX has bypass PMIC ready function, as this function
is normally NOT enabled on the board design, so we need
to bypass the PMIC ready pin check during DSM mode resume
flow, otherwise, the internal DSM resume logic will be
waiting for this signal to be ready forever and cause
resume fail.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Fixes: ff843d621bfc ("ARM: imx: add suspend support for i.mx6sx") Tested-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new task inherits cpus_allowed and mems_allowed masks from its parent,
but if someone changes cpuset's config by writing to cpuset.cpus/cpuset.mems
before this new task is inserted into the cgroup's task list, the new task
won't be updated accordingly.
The ethtool_ops .get_regs function attempts to read the nonexistent
register NIC_QSET_SQ_0_7_CNM_CHG, which produces a "bus error" type
OOPs.
Fix by not attempting to read, and removing the definition of,
NIC_QSET_SQ_0_7_CNM_CHG. A zero is written into the register dump to
keep the layout unchanged.
Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 8ead9dd54716 ("devpts: more pty driver interface cleanups") I
made devpts_get_priv() just return the dentry->fs_data directly. And
because I thought it wouldn't happen, I added a warning if you ever saw
a pts node that wasn't on devpts.
And no, that warning never triggered under any actual real use, but you
can trigger it by creating nonsensical pts nodes by hand.
So just revert the warning, and make devpts_get_priv() return NULL for
that case like it used to.
Some full-speed mceusb infrared transceivers contain invalid endpoint
descriptors for their interrupt endpoints, with bInterval set to 0.
In the past they have worked out okay with the mceusb driver, because
the driver sets the bInterval field in the descriptor to 1,
overwriting whatever value may have been there before. However, this
approach was never sanctioned by the USB core, and in fact it does not
work with xHCI controllers, because they use the bInterval value that
was present when the configuration was installed.
Currently usbcore uses 32 ms as the default interval if the value in
the endpoint descriptor is invalid. It turns out that these IR
transceivers don't work properly unless the interval is set to 10 ms
or below. To work around this mceusb problem, this patch changes the
endpoint-descriptor parsing routine, making the default interval value
be 10 ms rather than 32 ms.
The STiH4{07,10} platform contains some interconnect clocks which are used
by various IPs. If this clock isn't handled correctly by ST's EHCI/OHCI
drivers, their hub won't be found, the following error be shown and the
result will be non-working USB:
Problems with the signal integrity of the high speed USB data lines or
noise on reference ground lines can cause the i.MX6 USB controller to
violate USB specs and exhibit unexpected behavior.
It was observed that USBi_UI interrupts were triggered first and when
isr_setup_status_phase was called, ci->status was NULL, which lead to a
NULL pointer dereference kernel panic.
This patch fixes the kernel panic, emits a warning once and returns
-EPIPE to halt the device and let the host get stalled.
It also adds a comment to point people, who are experiencing this issue,
to their USB hardware design.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous driver is possible to stop the transfer wrongly.
For example:
1) An interrupt happens, but not BRDY interruption.
2) Read INTSTS0. And than state->intsts0 is not set to BRDY.
3) BRDY is set to 1 here.
4) Read BRDYSTS.
5) Clear the BRDYSTS. And then. the BRDY is cleared wrongly.
Remarks:
- The INTSTS0.BRDY is read only.
- If any bits of BRDYSTS are set to 1, the BRDY is set to 1.
- If BRDYSTS is 0, the BRDY is set to 0.
So, this patch adds condition to avoid such situation. (And about
NRDYSTS, this is not used for now. But, avoiding any side effects,
this patch doesn't touch it.)
Since the commit c1a67b48f6a5 ("serial: 8250_pci: replace switch-case by
formula for Intel MID"), the 8250 driver crashes in the byt_set_termios()
function with a divide error. This is caused by the fact that a baud rate of 0
(B0) is not handled properly. Fix it by falling back to B9600 in this case.
Reported-by: "Mendez Salinas, Fernando" <fernando.mendez.salinas@intel.com> Fixes: c1a67b48f6a5 ("serial: 8250_pci: replace switch-case by formula for Intel MID") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent fix to iio_buffer_read_first_n_outer removed ret from being set by
a return from wait_event_interruptible and also added a continue in a loop
which causes the variable ret to not be set when it reaches the end of the
loop. Fix this by initializing ret to zero.
Also remove extraneous white space at the end of the loop.
Fixes: fcf68f3c0bb2a5 ("fix sched WARNING "do not call blocking ops when !TASK_RUNNING") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
7985e7c100 ("iio: Introduce a new fractional value type") introduced a
new IIO_VAL_FRACTIONAL value type meant to represent rational type numbers
expressed by a numerator and denominator combination.
Formating of IIO_VAL_FRACTIONAL values relies upon do_div() usage. This
fails handling negative values properly since parameters are reevaluated
as unsigned values.
Fix this by using div_s64_rem() instead. Computed integer part will carry
properly signed value. Formatted fractional part will always be positive.
Fixes: 7985e7c100 ("iio: Introduce a new fractional value type") Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the scaling of the KXSD9 involves multiplication with a
fraction number < 1.
However the scaling value returned from IIO_INFO_SCALE was
unpredictable as only the micros of the value was assigned, and
not the integer part, resulting in scaling like this:
According to IIO ABI definition, IIO_PRESSURE data output unit is
kilopascal:
http://lxr.free-electrons.com/source/Documentation/ABI/testing/sysfs-bus-iio
This patch fix output unit of HID pressure sensor IIO driver from pascal to
kilopascal to follow IIO ABI definition.
In at least one known setup, the chip comes up in a state where reading
the chip ID returns garbage unless it's been reset, due to noise on the
wires during system boot.
All supported chips have the same reset method, and based on the
datasheets they all need 1.3 or 1.8ms to recover after reset. So, do
the conservative thing here and always reset the chip.
Signed-off-by: Olof Johansson <olof@lixom.net> Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the i2c_smbus_read_byte commmands used to retrieve the sensor
data with an i2c_master_recv command.
The smbus read byte method fails because the device does not expect a
stop condition after sending the first byte. When we issue the second
read, we are getting the first byte again. Net effect is that of the 14
bits used for the measurement, the 8 most significant bits are correct,
the lower 6 are not.
None of the smbus read protocols follow the pattern this device requires
(S Addr Rd [A] Data [A] Data NA P), hence the switch to an i2c receive
transaction.
Applicable from original introduction of this driver, but will require
backporting due to churn in the code.
Signed-off-by: Alison Schofield <amsfield22@gmail.com> Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver always assumes that an input device has been created when
reading channel 3. This causes a kernel panic when dereferencing
st->ts_input.
The change was introduced in
commit 84882b060301 ("iio: adc: at91_adc: Add support for touchscreens
without TSMR"). Earlier versions only entered that part of the if-else
statement if only the following flags are set:
The data buffer for captured mode for the ad799x driver is allocated in the
update_scan_mode() callback. This callback is not set in the iio_info
struct for the ad7791/ad7995/ad7999, which means that the data buffer is
not allocated when a captured transfer is started. As a result the driver
crashes when the first sample is received. To fix this properly set the
update_scan_mode() callback.
The call to i2c_get_clientdata(client) returns a struct iio_dev*, not
the needed struct ads1015_data*. We need here an intermediate step as
in the function: void ads1015_get_channels_config(struct i2c_client *client).
Signed-off-by: Giorgio Dal Molin <giorgio.nicole@arcor.de> Fixes: ecc24e72f437 ("iio: adc: Add TI ADS1015 ADC driver support") Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that open delay and sample delay for each channel is configurable
via DT, the default IDLE_TIMEOUT value is not enough as this is
calculated based on hardcoded macros. This results in driver returning
EBUSY sometimes. Fix this by increasing the timeout
value based on maximum value possible to open delay and sample delays
for each channel.
Fixes: 5dc11e810676e ("iio: adc: ti_am335x_adc: make sample delay, open delay, averaging DT parameters") Signed-off-by: Vignesh R <vigneshr@ti.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that two or more ADC channels can be simultaneously
requested for raw samples, in which case there can be race in access to
FIFO data resulting in loss of samples.
If am335x_tsc_se_set_once() is called again from tiadc_read_raw(), when
ADC is still acquired to sample one of the channels, the second process
might be put into uninterruptible sleep state. Fix these issues, by
protecting FIFO access and channel configurations with a mutex. Since
tiadc_read_raw() might take anywhere between few microseconds to few
milliseconds to finish execution (depending on averaging and delay
values supplied via DT), its better to use mutex instead of spinlock.
Use the IS_ENABLED() helper macro to ensure that the configfs group is
initialized either when configfs is built-in or when configfs is built as a
module. Otherwise software trigger creation will result in undefined
behaviour when configfs is built as a mdoule since the configfs group for
the trigger is not properly initialized.
Any readings from the raw interface of the KXSD9 driver will
return an empty string, because it does not return
IIO_VAL_INT but rather some random value from the accelerometer
to the caller.
When userspace sends KVM_SET_LAPIC, KVM schedules a check between
the vCPU's IRR and ISR and the IOAPIC redirection table, in order
to re-establish the IOAPIC's dest_map (the list of CPUs servicing
the real-time clock interrupt with the corresponding vectors).
However, __rtc_irq_eoi_tracking_restore_one was forgetting to
set dest_map->vectors. Because of this, the IOAPIC did not process
the real-time clock interrupt EOI, ioapic->rtc_status.pending_eoi
got stuck at a non-zero value, and further RTC interrupts were
reported to userspace as coalesced.
On arm/arm64, we depend on the kvm_unmap_hva* callbacks (via
mmu_notifiers::invalidate_*) to unmap the stage2 pagetables when
the userspace buffer gets unmapped. However, when the Hypervisor
process exits without explicit unmap of the guest buffers, the only
notifier we get is kvm_arch_flush_shadow_all() (via mmu_notifier::release
) which does nothing on arm. Later this causes us to access pages that
were already released [via exit_mmap() -> unmap_vmas()] when we actually
get to unmap the stage2 pagetable [via kvm_arch_destroy_vm() ->
kvm_free_stage2_pgd()]. This triggers crashes with CONFIG_DEBUG_PAGEALLOC,
which unmaps any free'd pages from the linear map.
As the meaning of these variables and pointers seems to change more
frequently, let's directly access our save area, instead of going via
current->thread.
Right now, this is broken for set/get_fpu. They simply overwrite the
host registers, as the pointers to the current save area were turned
into the static host save area.
Fixes: 3f6813b9a5e0 ("s390/fpu: allocate 'struct fpu' with the task_struct") Reported-by: Hao QingFeng <haoqf@linux.vnet.ibm.com> Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMD F12h machines have an erratum which can cause DIV/IDIV to behave
unpredictably. The workaround is to set MSRC001_1029[31] but sometimes
there is no BIOS update containing that workaround so let's do it
ourselves unconditionally. It is simple enough.
Łukasz Daniluk reported that on a RHEL kernel that his machine would lock up
after enabling function tracer. I asked him to bisect the functions within
available_filter_functions, which he did and it came down to three:
_paravirt_nop(), _paravirt_ident_32() and _paravirt_ident_64()
It was found that this is only an issue when noreplace-paravirt is added
to the kernel command line.
This means that those functions are most likely called within critical
sections of the funtion tracer, and must not be traced.
In newer kenels _paravirt_nop() is defined within gcc asm(), and is no
longer an issue. But both _paravirt_ident_{32,64}() causes the
following splat when they are traced:
track_pfn_insert() in vmf_insert_pfn_pmd() is marking dax mappings as
uncacheable rendering them impractical for application usage. DAX-pte
mappings are cached and the goal of establishing DAX-pmd mappings is to
attain more performance, not dramatically less (3 orders of magnitude).
track_pfn_insert() relies on a previous call to reserve_memtype() to
establish the expected page_cache_mode for the range. While memremap()
arranges for reserve_memtype() to be called, devm_memremap_pages() does
not. So, teach track_pfn_insert() and untrack_pfn() how to handle
tracking without a vma, and arrange for devm_memremap_pages() to
establish the write-back-cache reservation in the memtype tree.
Cc: Matthew Wilcox <mawilcox@microsoft.com> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Nilesh Choudhury <nilesh.choudhury@oracle.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reported-by: Toshi Kani <toshi.kani@hpe.com> Reported-by: Kai Zhang <kai.ka.zhang@oracle.com> Acked-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Active QSFP cables were reset only every alternate iteration of the
channel tuning algorithm instead of every iteration due to incorrect
reset of the flag that controlled QSFP reset, resulting in using stale
QSFP status in the channel tuning algorithm.
Fixes: 8ebd4cf1852a ("Add active and optical cable support") Reviewed-by: Dean Luick <dean.luick@intel.com> Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes an oops that might happen if uverbs_close races with
remove_one.
Both contexts may run ib_uverbs_cleanup_ucontext, it depends
on the flow.
Currently, there is no protection for a case that remove_one
didn't make the cleanup it runs to its end, the underlying
ib_device was freed then uverbs_close will call
ib_uverbs_cleanup_ucontext and OOPs.
Above might happen if uverbs_close deleted the file from the list
then remove_one didn't find it and runs to its end.
Fixes to protect against that case by a new cleanup lock so that
ib_uverbs_cleanup_ucontext will be called always before that
remove_one is ended.
Fixes: 35d4a0b63dc0 ("IB/uverbs: Fix race between ib_uverbs_open and remove_one") Reported-by: Devesh Sharma <devesh.sharma@broadcom.com> Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The qp init function does a kzalloc() while holding the RCU
lock that encounters the following warning with a debug kernel
when a cat of the qp_stats is done:
v4.8-rc3 commit 99f3c90d0d ("dm flakey: error READ bios during the
down_interval") overlooked the 'drop_writes' feature, which is meant to
allow reads to be issued rather than errored, during the down_interval.
Fixes: 99f3c90d0d ("dm flakey: error READ bios during the down_interval") Reported-by: Qu Wenruo <quwenruo@cn.fujitsu.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to the change the function would blindly deference mm, exe_file
and exe_file->f_inode, each of which could have been NULL or freed.
Use get_task_exe_file to safely obtain stable exe_file.
Signed-off-by: Mateusz Guzik <mguzik@redhat.com> Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Acked-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For more convenient access if one has a pointer to the task.
As a minor nit take advantage of the fact that only task lock + rcu are
needed to safely grab ->exe_file. This saves mm refcount dance.
Use the helper in proc_exe_link.
Signed-off-by: Mateusz Guzik <mguzik@redhat.com> Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Acked-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KASAN allocates memory from the page allocator as part of
kmem_cache_free(), and that can reference current->mempolicy through any
number of allocation functions. It needs to be NULL'd out before the
final reference is dropped to prevent a use-after-free bug:
BUG: KASAN: use-after-free in alloc_pages_current+0x363/0x370 at addr ffff88010b48102c
CPU: 0 PID: 15425 Comm: trinity-c2 Not tainted 4.8.0-rc2+ #140
...
Call Trace:
dump_stack
kasan_object_err
kasan_report_error
__asan_report_load2_noabort
alloc_pages_current <-- use after free
depot_save_stack
save_stack
kasan_slab_free
kmem_cache_free
__mpol_put <-- free
do_exit
This patch sets current->mempolicy to NULL before dropping the final
reference.
There have been several reports about pre-mature OOM killer invocation
in 4.7 kernel when order-2 allocation request (for the kernel stack)
invoked OOM killer even during basic workloads (light IO or even kernel
compile on some filesystems). In all reported cases the memory is
fragmented and there are no order-2+ pages available. There is usually
a large amount of slab memory (usually dentries/inodes) and further
debugging has shown that there are way too many unmovable blocks which
are skipped during the compaction. Multiple reporters have confirmed
that the current linux-next which includes [1] and [2] helped and OOMs
are not reproducible anymore.
A simpler fix for the late rc and stable is to simply ignore the
compaction feedback and retry as long as there is a reclaim progress and
we are not getting OOM for order-0 pages. We already do that for
CONFING_COMPACTION=n so let's reuse the same code when compaction is
enabled as well.
If kexec_apply_relocations fails, kexec_load_purgatory frees pi->sechdrs
and pi->purgatory_buf. This is redundant, because in case of error
kimage_file_prepare_segments calls kimage_file_post_load_cleanup, which
will also free those buffers.
This causes two warnings like the following, one for pi->sechdrs and the
other for pi->purgatory_buf:
kexec-bzImage64: Loading purgatory failed
------------[ cut here ]------------
WARNING: CPU: 1 PID: 2119 at mm/vmalloc.c:1490 __vunmap+0xc1/0xd0
Trying to vfree() nonexistent vm area (ffffc90000e91000)
Modules linked in:
CPU: 1 PID: 2119 Comm: kexec Not tainted 4.8.0-rc3+ #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
dump_stack+0x4d/0x65
__warn+0xcb/0xf0
warn_slowpath_fmt+0x4f/0x60
? find_vmap_area+0x19/0x70
? kimage_file_post_load_cleanup+0x47/0xb0
__vunmap+0xc1/0xd0
vfree+0x2e/0x70
kimage_file_post_load_cleanup+0x5e/0xb0
SyS_kexec_file_load+0x448/0x680
? putname+0x54/0x60
? do_sys_open+0x190/0x1f0
entry_SYSCALL_64_fastpath+0x13/0x8f
---[ end trace 158bb74f5950ca2b ]---
Fix by setting pi->sechdrs an pi->purgatory_buf to NULL, since vfree
won't try to free a NULL pointer.
Link: http://lkml.kernel.org/r/1472083546-23683-1-git-send-email-bauerman@linux.vnet.ibm.com Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Dave Young <dyoung@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that we conform to the algorithm described in RFC5661, section
18.36.4 for when to bump the sequence id. In essence we do it for all
cases except when the RPC call timed out, or in case of the server returning
NFS4ERR_DELAY or NFS4ERR_STALE_CLIENTID.
According to RFC5661, the client is responsible for serialising
LAYOUTGET and LAYOUTRETURN to avoid ambiguity. Consider the case
where we send both in parallel.
Client Server
====== ======
LAYOUTGET(seqid=X)
LAYOUTRETURN(seqid=X)
LAYOUTGET return seqid=X+1
LAYOUTRETURN return seqid=X+2
Process LAYOUTRETURN
Forget layout stateid
Process LAYOUTGET
Set seqid=X+1
The client processes the layoutget/layoutreturn in the wrong order,
and since the result of the layoutreturn was to clear the only
existing layout segment, the client forgets the layout stateid.
When the LAYOUTGET comes in, it is treated as having a completely
new stateid, and so the client sets the wrong sequence id...
Fix is to check if there are outstanding LAYOUTGET requests
before we send the LAYOUTRETURN (note that LAYOUGET will already
wait if it sees an outstanding LAYOUTRETURN).
nfsd4_release_lockowner finds a lock owner that has no lock state,
and drops cl_lock. Then release_lockowner picks up cl_lock and
unhashes the lock owner.
During the window where cl_lock is dropped, I don't see anything
preventing a concurrent nfsd4_lock from finding that same lock owner
and adding lock state to it.
Move release_lockowner() into nfsd4_release_lockowner and hang onto
the cl_lock until after the lock owner's state cannot be found
again.
Found by inspection, we don't currently have a reproducer.
Fixes: 2c41beb0e5cf ("nfsd: reduce cl_lock thrashing in ... ") Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that the client conforms to the normative behaviour described in
RFC5661 Section 12.7.2: "If a client believes its lease has expired,
it MUST NOT send I/O to the storage device until it has validated its
lease."
So ensure that we wait for the lease to be validated before using
the layout.
If the attempt to connect to a DS fails inside ff_layout_pg_init_read or
ff_layout_pg_init_write, then we currently end up clearing the layout
segment carried by the struct nfs_pageio_descriptor, causing an Oops
when we later call into ff_layout_read_pagelist/ff_layout_write_pagelist.
The fix is to ensure we return the layout and then retry.
Fixes: 446ca2195303 ("pNFS/flexfiles: When initing reads or writes, we...") Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kernfs_notify_workfn() sends out file modified events for the
scheduled kernfs_nodes. Because the modifications aren't from
userland, it doesn't have the matching file struct at hand and can't
use fsnotify_modify(). Instead, it looked up the inode and then used
d_find_any_alias() to find the dentry and used fsnotify_parent() and
fsnotify() directly to generate notifications.
The assumption was that the relevant dentries would have been pinned
if there are listeners, which isn't true as inotify doesn't pin
dentries at all and watching the parent doesn't pin the child dentries
even for dnotify. This led to, for example, inotify watchers not
getting notifications if the system is under memory pressure and the
matching dentries got reclaimed. It can also be triggered through
/proc/sys/vm/drop_caches or a remount attempt which involves shrinking
dcache.
fsnotify_parent() only uses the dentry to access the parent inode,
which kernfs can do easily. Update kernfs_notify_workfn() so that it
uses fsnotify() directly for both the parent and target inodes without
going through d_find_any_alias(). While at it, supply the target file
name to fsnotify() from kernfs_node->name.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Evgeny Vereshchagin <evvers@ya.ru> Fixes: d911d9874801 ("kernfs: make kernfs_notify() trigger inotify events too") Cc: John McCutchan <john@johnmccutchan.com> Cc: Robert Love <rlove@rlove.org> Cc: Eric Paris <eparis@parisplace.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In pnv_ioda_free_pe(), the PE object (including the associated PE
number) is cleared before resetting the corresponding bit in the
PE allocation bitmap. It means PE#0 is always released to the bitmap
wrongly.
This fixes above issue by caching the PE number before the PE object
is cleared.
Fixes: 1e9167726c41 ("powerpc/powernv: Use PE instead of number during setup and release" Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit c60ac5693c47 ("powerpc: Update kernel VSID range", 2013-03-13)
we lost a check on the region number (the top four bits of the effective
address) for addresses below PAGE_OFFSET. That commit replaced a check
that the top 18 bits were all zero with a check that bits 46 - 59 were
zero (performed for all addresses, not just user addresses).
This means that userspace can access an address like 0x1000_0xxx_xxxx_xxxx
and we will insert a valid SLB entry for it. The VSID used will be the
same as if the top 4 bits were 0, but the page size will be some random
value obtained by indexing beyond the end of the mm_ctx_high_slices_psize
array in the paca. If that page size is the same as would be used for
region 0, then userspace just has an alias of the region 0 space. If the
page size is different, then no HPTE will be found for the access, and
the process will get a SIGSEGV (since hash_page_mm() will refuse to create
a HPTE for the bogus address).
The access beyond the end of the mm_ctx_high_slices_psize can be at most
5.5MB past the array, and so will be in RAM somewhere. Since the access
is a load performed in real mode, it won't fault or crash the kernel.
At most this bug could perhaps leak a little bit of information about
blocks of 32 bytes of memory located at offsets of i * 512kB past the
paca->mm_ctx_high_slices_psize array, for 1 <= i <= 11.
In a situation, where Linux kernel gets notified about duplicate error log
from OPAL, it is been observed that kernel fails to remove sysfs entries
(/sys/firmware/opal/elog/0xXXXXXXXX) of such error logs. This is because,
we currently search the error log/dump kobject in the kset list via
'kset_find_obj()' routine. Which eventually increment the reference count
by one, once it founds the kobject.
So, unless we decrement the reference count by one after it found the kobject,
we would not be able to release the kobject properly later.
This patch adds the 'kobject_put()' which was missing earlier.
tabort_syscall runs with RI=1, so a nested recoverable machine
check will load the paca into r13 and overwrite what we loaded
it with, because exceptions returning to privileged mode do not
restore r13.
Fixes: b4b56f9ecab4 (powerpc/tm: Abort syscalls in active transactions) Signed-off-by: Nick Piggin <npiggin@gmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 76174004a0f19785a328f40388e87e982bbf69b9
(tcp: do not slow start when cwnd equals ssthresh )
introduced regression in TCP YeAH. Using 100ms delay 1% loss virtual
ethernet link kernel 4.2 shows bandwidth ~500KB/s for single TCP
connection and kernel 4.3 and above (including 4.8-rc4) shows bandwidth
~100KB/s.
That is caused by stalled cwnd when cwnd equals ssthresh. This patch
fixes it by proper increasing cwnd in this case.
Signed-off-by: Artem Germanov <agermanov@anchorfree.com> Acked-by: Dmitry Adamushko <d.adamushko@anchorfree.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently vlan tagged packets were not parsed correctly
and assumed to be regular IPv4/IPv6 packets.
We should check for 802.1Q/802.1ad tags and update the lro header
accordingly.
This fixes the use case where LRO is on and rxvlan is off
(vlan stripping is off).
Fixes: e586b3b0baee ('net/mlx5: Ethernet Datapath files') Signed-off-by: Gal Pressman <galp@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DATA and/or FIN are carried in a SYN/ACK message or SYN message,
we append an skb in socket receive queue, but we forget to call
sk_forced_mem_schedule().
Effect is that the socket has a negative sk->sk_forward_alloc as long as
the message is not read by the application.
Josh Hunt fixed a similar issue in commit d22e15371811 ("tcp: fix tcp
fin memory accounting")
Fixes: 168a8f58059a ("tcp: TCP Fast Open Server - main code path") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Josh Hunt <johunt@akamai.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In general, when DAD detected IPv6 duplicate address, ifp->state
will be set to INET6_IFADDR_STATE_ERRDAD and DAD is stopped by a
delayed work, the call tree should be like this:
ndisc_recv_ns
-> addrconf_dad_failure <- missing ifp put
-> addrconf_mod_dad_work
-> schedule addrconf_dad_work()
-> addrconf_dad_stop() <- missing ifp hold before call it
addrconf_dad_failure() called with ifp refcont holding but not put.
addrconf_dad_work() call addrconf_dad_stop() without extra holding
refcount. This will not cause any issue normally.
But the race between addrconf_dad_failure() and addrconf_dad_work()
may cause ifp refcount leak and netdevice can not be unregister,
dmesg show the following messages:
IPv6: eth0: IPv6 duplicate address fe80::XX:XXXX:XXXX:XX detected!
...
unregister_netdevice: waiting for eth0 to become free. Usage count = 1
Cc: stable@vger.kernel.org Fixes: c15b1ccadb32 ("ipv6: move DAD and addrconf_verify processing
to workqueue") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a code path where we are calling __iowrite64_copy() on
an address that is not 64-bit aligned. This causes an exception on
some architectures such as arm64. Fix that code path by using
__iowrite32_copy().
Reported-by: JD Zheng <jiandong.zheng@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neither the failure or success paths of ping_v6_sendmsg release
the dst it acquires. This leads to a flood of warnings from
"net/core/dst.c:288 dst_release" on older kernels that
don't have 8bf4ada2e21378816b28205427ee6b0e1ca4c5f1 backported.
That patch optimistically hoped this had been fixed post 3.10, but
it seems at least one case wasn't, where I've seen this triggered
a lot from machines doing unprivileged icmp sockets.
Cc: Martin Lau <kafai@fb.com> Signed-off-by: Dave Jones <davej@codemonkey.org.uk> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now we use the 'readlock' both for protecting some of the af_unix
IO path and for making the bind be single-threaded.
The two are independent, but using the same lock makes for a nasty
deadlock due to ordering with regards to filesystem locking. The bind
locking would want to nest outside the VSF pathname locking, but the IO
locking wants to nest inside some of those same locks.
We tried to fix this earlier with commit c845acb324aa ("af_unix: Fix
splice-bind deadlock") which moved the readlock inside the vfs locks,
but that caused problems with overlayfs that will then call back into
filesystem routines that take the lock in the wrong order anyway.
Splitting the locks means that we can go back to having the bind lock be
the outermost lock, and we don't have any deadlocks with lock ordering.
Acked-by: Rainer Weikusat <rweikusat@cyberadapt.com> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that it just replaces one deadlock with another one: we can
still get the wrong lock ordering with the readlock due to overlayfs
calling back into the filesystem layer and still taking the vfs locks
after the readlock.
The proper solution ends up being to just split the readlock into two
pieces: the bind lock (taken *outside* the vfs locks) and the IO lock
(taken *inside* the filesystem locks). The two locks are independent
anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(a) Create bonding master
> modprobe bonding miimon=50
(b) Create macvlan bridge on eth2
> ip link add link eth2 dev mvl0 address aa:0:0:0:0:01 \
type macvlan
(c) Now try adding eth2 into the bond
> echo +eth2 > /sys/class/net/bond0/bonding/slaves
<crash>
Bonding does lots of things before checking if the device enslaved is
busy or not.
In this case when the notifier call-chain sends notifications, the
bond_netdev_event() assumes that the rx_handler /rx_handler_data is
registered while the bond_enslave() hasn't progressed far enough to
register rx_handler for the new slave.
This patch adds a rx_handler check that can be performed right at the
beginning of the enslave code to avoid getting into this situation.
Signed-off-by: Mahesh Bandewar <maheshb@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is because on the error path, after we install
the new socket file, we call sock_release() to clean
up the socket, which leaves the fd pointing to a freed
socket. Fix this by calling sys_close() on that fd
directly.
Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module") Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc8c20acaea1 ("bridge: multicast: treat igmpv3 report with
INCLUDE and no sources as a leave") seems to have accidentally reverted
commit 47cc84ce0c2f ("bridge: fix parsing of MLDv2 reports"). This
commit brings back a change to br_ip6_multicast_mld2_report() where
parsing of MLDv2 reports stops when the first group is successfully
added to the MDB cache.
Fixes: bc8c20acaea1 ("bridge: multicast: treat igmpv3 report with INCLUDE and no sources as a leave") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b70661c70830 ("net: smc91x: use run-time configuration on all ARM
machines") broke some ARM platforms through several mistakes. Firstly,
the access size must correspond to the following rule:
(a) at least one of 16-bit or 8-bit access size must be supported
(b) 32-bit accesses are optional, and may be enabled in addition to
the above.
Secondly, it provides no emulation of 16-bit accesses, instead blindly
making 16-bit accesses even when the platform specifies that only 8-bit
is supported.
Reorganise smc91x.h so we can make use of the existing 16-bit access
emulation already provided - if 16-bit accesses are supported, use
16-bit accesses directly, otherwise if 8-bit accesses are supported,
use the provided 16-bit access emulation. If neither, BUG(). This
exactly reflects the driver behaviour prior to the commit being fixed.
Since the conversion incorrectly cut down the available access sizes on
several platforms, we also need to go through every platform and fix up
the overly-restrictive access size: Arnd assumed that if a platform can
perform 32-bit, 16-bit and 8-bit accesses, then only a 32-bit access
size needed to be specified - not so, all available access sizes must
be specified.
This likely fixes some performance regressions in doing this: if a
platform does not support 8-bit accesses, 8-bit accesses have been
emulated by performing a 16-bit read-modify-write access.
Tested on the Intel Assabet/Neponset platform, which supports only 8-bit
accesses, which was broken by the original commit.
Fixes: b70661c70830 ("net: smc91x: use run-time configuration on all ARM machines") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts:
commit 33c133cc7598 ("phy: IRQ cannot be shared")
On hardware with multiple PHY devices hooked up to the same IRQ line, allow
them to share it.
Sergei Shtylyov says:
"I'm not sure now what was the reason I concluded that the IRQ sharing
was impossible... most probably I thought that the kernel IRQ handling
code exited the loop over the IRQ actions once IRQ_HANDLED was returned
-- which is obviously not so in reality..."
Signed-off-by: Xander Huff <xander.huff@ni.com> Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We kept shadow copies of which interrupt sources we have enabled and
disabled, but due to an order bug in how intrl2_mask_clear was defined,
we could run into the following scenario:
CPU0 CPU1
intrl2_1_mask_clear(..)
sets INTRL2_CPU_MASK_CLEAR
bcm_sf2_switch_1_isr
read INTRL2_CPU_STATUS and masks with stale
irq1_mask value
updates irq1_mask value
Which would make us loop again and again trying to process and interrupt
we are not clearing since our copy of whether it was enabled before
still indicates it was not. Fix this by updating the shadow copy first,
and then unasking at the HW level.
Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using sock_tx_timestamp, use skb_tx_timestamp to record
software transmit timestamp of a packet.
sock_tx_timestamp resets and overrides the tx_flags of the skb.
The function is intended to be called from within the protocol
layer when creating the skb, not from a device driver. This is
inconsistent with other drivers and will cause issues for TCP.
In TCP, we intend to sample the timestamps for the last byte
for each sendmsg/sendpage. For that reason, tcp_sendmsg calls
tcp_tx_timestamp only with the last skb that it generates.
For example, if a 128KB message is split into two 64KB packets
we want to sample the SND timestamp of the last packet. The current
code in the tun driver, however, will result in sampling the SND
timestamp for both packets.
Also, when the last packet is split into smaller packets for
retranmission (see tcp_fragment), the tun driver will record
timestamps for all of the retransmitted packets and not only the
last packet.
Fixes: eda297729171 (tun: Support software transmit time stamping.) Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Francis Yan <francisyyan@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function sctp_diag_dump_one() currently performs a memcpy()
of 64 bytes from a 16 byte field into another 16 byte field. Fix
by using correct size, use sizeof to obtain correct size instead
of using a hard-coded constant.
Fixes: 8f840e47f190 ("sctp: add the sctp_diag.c file") Signed-off-by: Lance Richardson <lrichard@redhat.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laura tracked poll() [and friends] regression caused by commit e6afc8ace6dd ("udp: remove headers from UDP packets before queueing")
udp_poll() needs to know if there is a valid packet in receive queue,
even if its payload length is 0.
Change first_packet_length() to return an signed int, and use -1
as the indication of an empty queue.
Fixes: e6afc8ace6dd ("udp: remove headers from UDP packets before queueing") Reported-by: Laura Abbott <labbott@redhat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Tested-by: Laura Abbott <labbott@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Encoding of the metadata was using the padded length as opposed to
the real length of the data which is a bug per specification.
This has not been an issue todate because all metadatum specified
so far has been 32 bit where aligned and data length are the same width.
This also includes a bug fix for validating the length of a u16 field.
But since there is no metadata of size u16 yes we are fine to include it
here.
While at it get rid of magic numbers.
Fixes: ef6980b6becb ("net sched: introduce IFE action") Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wrong key is used when extracting the address type field set by
the flower offload code. We have to use the control key and not the
basic key, fix that.
Fixes: e3a2b7ed018e ('net/mlx5e: Support offload cls_flower with drop action') Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set and verify signature calculates the signature for each of the
mailbox nodes, even for those that are unused (from cache). Added
a missing length check to set and verify only those which are used.
While here, also moved the setting of msg's nodes token to where we
already go over them. This saves a pass because checksum is disabled,
and the only useful thing remaining that set signature does is setting
the token.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB
adapters') Signed-off-by: Paul Blakey <paulb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When tcp_sendmsg() allocates a fresh and empty skb, it puts it at the
tail of the write queue using tcp_add_write_queue_tail()
Then it attempts to copy user data into this fresh skb.
If the copy fails, we undo the work and remove the fresh skb.
Unfortunately, this undo lacks the change done to tp->highest_sack and
we can leave a dangling pointer (to a freed skb)
Later, tcp_xmit_retransmit_queue() can dereference this pointer and
access freed memory. For regular kernels where memory is not unmapped,
this might cause SACK bugs because tcp_highest_sack_seq() is buggy,
returning garbage instead of tp->snd_nxt, but with various debug
features like CONFIG_DEBUG_PAGEALLOC, this can crash the kernel.
This bug was found by Marco Grassi thanks to syzkaller.
Fixes: 6859d49475d4 ("[TCP]: Abstract tp->highest_sack accessing & point to next skb") Reported-by: Marco Grassi <marco.gra@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Cc: Yuchung Cheng <ycheng@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I feel like we should maybe return -ENOMEM or -ENOBUFS, but I'm not sure
userspace is equipped to handle that. Anyway, this is better than a GPF
and looks somewhat consistent with other tipc_msg_create() callers.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IPv6 is disabled when the option is set to keep IPv6
addresses on link down, userspace is unaware of this as
there is no such indication via netlink. The solution is to
remove the IPv6 addresses in this case, which results in
netlink messages indicating removal of addresses in the
usual manner. This fix also makes the behavior consistent
with the case of having IPv6 disabled first, which stops
IPv6 addresses from being added.
Fixes: f1705ec197e7 ("net: ipv6: Make address flushing on ifdown optional") Signed-off-by: Mike Manning <mmanning@brocade.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should initialize sctp_ht_iter::start_fail to zero if ->start()
succeeds, otherwise it's possible that we leave an old value of 1 there,
which will cause ->stop() to not call sctp_transport_walk_stop(), which
causes all sorts of problems like not calling rcu_read_unlock() (and
preempt_enable()), eventually leading to more warnings like this:
BUG: sleeping function called from invalid context at mm/slab.h:388
in_atomic(): 0, irqs_disabled(): 0, pid: 16551, name: trinity-c2
Preemption disabled at:[<ffffffff819bceb6>] rhashtable_walk_start+0x46/0x150
Notice that this is a subtly different stacktrace from the one in commit 5fc382d875 ("net/sctp: terminate rhashtable walk correctly").
Cc: Xin Long <lucien.xin@gmail.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Acked-By: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If iriap_register_lsap() fails to allocate memory, self->lsap is
set to NULL. However, none of the callers handle the failure and
irlmp_connect_request() will happily dereference it:
There's more problems with missing error checks in iriap_init() (and
indeed all of irda_init()), but that's a bigger problem that needs
very careful review and testing. This patch will fix the most serious
bug (as it's easily reached from unprivileged userspace).
I have tested my patch with a reproducer.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
