John Crispin [Sun, 20 Mar 2016 14:41:21 +0000 (14:41 +0000)]
oxnas: also reset GPIO B registers on boot
Clear both, SYS_CTRL_*_SEL and SEC_CTRL_*_SEL on boot instead of
writing to SYS_CTRL_*_SEL twice which looks like a copy-paste error.
Thanks to anonymous to bring this up in #21892!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 49042
Hauke Mehrtens [Sat, 19 Mar 2016 11:00:09 +0000 (11:00 +0000)]
linux-firmware: fix rt73-usb-firmware package
Some parts of this package were named rt73-pci-firmware before which
looks like a copy and past error. This renames all parts to rt73-usb-
firmware and then the firmware gets build and the dependencies from the
package with the kernel module are also working correctly.
John Crispin [Wed, 16 Mar 2016 09:27:14 +0000 (09:27 +0000)]
ar71xx: Use PHY fixups for Open Mesh MR1750
The delays of PHY/MAC on the MR1750 are done by u-boot and OpenWrt in
different ways. u-boot only modifies the ETH_CFG of the QCA955x based on
the link speed. But OpenWrt can only modify the PHY delays based on the
link speed.
This can lead to communication problems when u-boot initializes the ETH_CFG
for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY
delays to an incompatible value.
Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and
only rely on the AT803x PHY settings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49031
John Crispin [Wed, 16 Mar 2016 09:27:11 +0000 (09:27 +0000)]
ar71xx: Use PHY fixups for Open Mesh MR900
The delays of PHY/MAC on the MR900 are done by u-boot and OpenWrt in
different ways. u-boot only modifies the ETH_CFG of the QCA955x based on
the link speed. But OpenWrt can only modify the PHY delays based on the
link speed.
This can lead to communication problems when u-boot initializes the ETH_CFG
for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY
delays to an incompatible value.
Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and
only rely on the AT803x PHY settings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49030
John Crispin [Wed, 16 Mar 2016 09:27:08 +0000 (09:27 +0000)]
ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x
Some u-boot versions for QCA955x change the delays based on the link speed
during boot. This usually breaks the support of other linkspeeds when
OpenWrt is booted. It also conflicts with the
at803x_platform_data::fixup_rgmii_tx_delay. OpenWrt has to set its own
values in QCA955X_GMAC_REG_ETH_CFG.
The default RGMII values from the Atheros u-boot are currently used to
preset the existing mach files. These may have to be adjusted for boards
using different values but which are not currently set them explicitely in
OpenWrt.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Cc: Gabor Juhos <juhosg@openwrt.org> Cc: Imre Kaloz <kaloz@openwrt.org> Cc: Christian Beier <cb@shoutrlabs.com> Cc: Chris R Blake <chrisrblake93@gmail.com> Cc: Benjamin Berg <benjamin@sipsolutions.net> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> Cc: Matthias Schiffer <mschiffer@universe-factory.net> Cc: Dirk Neukirchen <dirkneukirchen@web.de> Cc: Christian Mehlis <christian@m3hlis.de> Cc: Luka Perkov <luka@openwrt.org> Cc: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 49029
John Crispin [Wed, 16 Mar 2016 09:27:04 +0000 (09:27 +0000)]
ar71xx: Clear bits in ath79_setup_qca955x_eth_cfg
Some u-boot versions for QCA955x set currently not cleared bits depending
on the used link speed. This breaks the rx/tx under OpenWrt. The mach-*.c
file is responsible to select the correct configuration bits and thus the
ath79_setup_qca955x_eth_cfg has to clear the unset.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49028
John Crispin [Wed, 16 Mar 2016 09:26:51 +0000 (09:26 +0000)]
tools/flex: update to 2.6.1
Update flex to 2.6.1
* Flex has moved to Github, adjust download link
* Remove patch that has been applied upstream
* Disable building tests to avoid circular dependency to bison
- disable also docs and examples at the same time
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 49025
John Crispin [Wed, 16 Mar 2016 09:26:48 +0000 (09:26 +0000)]
ramips: Add support for Xiaomi MiWiFi Nano
Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
v3 includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds
Luka Perkov [Mon, 14 Mar 2016 17:06:16 +0000 (17:06 +0000)]
uboot-kirkwood/goflexhome: update bootargs to use new ubi style
Since switching to new ubi(kernel,squashfs,ubifs) layout, the kernel lies in a
ubi volume. Dropping the mtd parts because the mtd layout is saved in the
device-tree, which is appended to the zImage.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49016
Luka Perkov [Mon, 14 Mar 2016 17:06:14 +0000 (17:06 +0000)]
kirkwood/goflexhome/goflexnet: merge "root" and unused mtd partitions into one volume "ubi"
The kernel will automatic attach mtd partitions named 'ubi' to ubi0.
Renaming the "root" partition into "ubi" will safe arguments
from the kernel cmdline.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49014
Rafał Miłecki [Fri, 11 Mar 2016 21:31:34 +0000 (21:31 +0000)]
brcm47xx: image: create standard TRX images using new building system
Apart from using our new building system there are 2 more changes:
1) Limit amount of images
So far we were generating all standard images (optimized one and two
with no loader) for every SUBTARGET. This is not needed, as e.g. the
only device requiring gzipped kernel is legacy Huawei E970.
2) Change output names
The new image building system requires specifying device name. This
forced picking some and resulted in:
openwrt-brcm47xx-$(SUBTARGET)-squashfs.trx
openwrt-brcm47xx-$(SUBTARGET)-squashfs-gz.trx
openwrt-brcm47xx-$(SUBTARGET)-squashfs-noloader-nodictionary.trx
becoming:
openwrt-brcm47xx-$(SUBTARGET)-standard-squashfs.trx
openwrt-brcm47xx-$(SUBTARGET)-standard-noloader-gz-squashfs.trx
openwrt-brcm47xx-$(SUBTARGET)-standard-noloader-nodictionarylzma-squashfs.trx
John Crispin [Thu, 10 Mar 2016 19:12:15 +0000 (19:12 +0000)]
tools/cmake: fix compile on Alpine Linux
internal jsoncpp include order leads to multiple build
errors on Alpine Linux which uses musl libc
use include order from upstream jsoncpp
first error was:
In file included from /usr/include/c++/5.3.0/stdexcept:38:0,
from /home/..../openwrt/build_dir/host/cmake-3.4.3/Utilities/cmjsoncpp/include/json/assertions.h:16,
from /home/..../openwrt/build_dir/host/cmake-3.4.3/Utilities/cmjsoncpp/src/lib_json/json_reader.cpp:7:
/usr/include/c++/5.3.0/exception:35:9: error: '#pragma' is not allowed here
#pragma GCC visibility push(default)
John Crispin [Thu, 10 Mar 2016 19:12:10 +0000 (19:12 +0000)]
ramips: Add support for GL-MT750
This patch adds support for GL-MT750.
GL-MT750 is powered by MT7620A and MT7610e, dual band 802.11ac, 2.4G 300Mbps and 5G 450Mbps.
It has 5 LANs, MMC interface, USB, a lot of IOs and PoE support.
John Crispin [Thu, 10 Mar 2016 19:11:28 +0000 (19:11 +0000)]
oxnas: clean-up NAND driver to fix probing issue
A re-write of the driver based on xway_nand.c and constants as
well as the cmd_ctrl() function from the original oxnas_nand.c
resulted in a extremely similar looking file (see diffsize),
and fixes the issue of NAND not being detected on newer kernels.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 48986
John Crispin [Thu, 10 Mar 2016 19:11:17 +0000 (19:11 +0000)]
procd: support pidfile writing.
procd from revision b12bb150ed38a4409bef5127c77b060ee616b860 supports
writing a pidfile. This adds support for setting that parameter with
standard init script hooks:
procd_set_param pidfile /var/run/someprocess.pid
Signed-off-by: Karl Palsson <karlp@etactica.com>
SVN-Revision: 48984
John Crispin [Thu, 10 Mar 2016 19:11:09 +0000 (19:11 +0000)]
kernel: Linux IP Virtual Server kernel modules (netfilter.mk patch)
IPVS (IP Virtual Server) implements transport-layer load balancing inside the Linux kernel
so called Layer-4 switching.
IPVS running on a host acts as a load balancer at the front of a cluster of real servers, it
can direct requests for TCP/UDP based services to the real servers, and makes services of
the real servers to appear as a virtual service on a single IP address.
John Crispin [Thu, 10 Mar 2016 19:10:54 +0000 (19:10 +0000)]
brcm63xx/lzma-loader: fix O32 ABI conformance
According to the calling convention of the o32 ABI the caller
function must reserve stack space for $a0-$a3 registers in case
the callee needs to save its arguments.
The assembly code of the loader does not reserve stack space for
these registers thus when the 'loader_main' function needs to save
its arguments, those will be stored in the 'workspace' area instead
of the stack.
Because the workspace area is also used by other part of the code, the
saved register values gets overwritten and this often leads to failed
kernel boots.
Fix the code to reserve stack space for the registers to avoid this
error.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
[noltari: apply the fix for brcm63xx too] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48979
John Crispin [Tue, 8 Mar 2016 18:11:59 +0000 (18:11 +0000)]
ramips: add support for Planex MZK-WDPR.
add support for Planex MZK-WDPR.
MZK-WDPR(MZK-WDPR-R01) is internet radio tuner.
This patch is "network board" in MZK-WDPR.
LCD board is non OpenWrt Platform.
Rafał Miłecki [Mon, 7 Mar 2016 22:37:09 +0000 (22:37 +0000)]
mac80211: backport brcmfmac patchset with driver setting concept
This prepares brcmfmac for better country handling and fixes BCM4360
support which was always failing with:
[ 13.249195] brcmfmac: brcmf_pcie_download_fw_nvram: FW failed to initialize
Felix Fietkau [Mon, 7 Mar 2016 11:03:41 +0000 (11:03 +0000)]
ltq-vdsl-app: do not set the reserved bit 4 in the xTSE 8
I do not know if this causes any problems now, but we should not set
it, because it is reserved. Some more recent versions of the Lantiq DSL
API driver and Control is checking if only valid bits are set.
Felix Fietkau [Mon, 7 Mar 2016 11:03:38 +0000 (11:03 +0000)]
ltq-vdsl-app: make it possible to configure ADSL/VDSL independently
There are some cases where ISPs are running ATM over VDSL or PTM over
ADSL, this is not the common case, but these cases exist. Make it
possible to configure OpenWrt for such cases by adding a new config
option line_mode.
Felix Fietkau [Mon, 7 Mar 2016 11:03:35 +0000 (11:03 +0000)]
ltq-vdsl-app: sync annex option between from ADSL package
The detailed annex option were only available in the danube DSL app
including the activation of G.992.2 Annex A (ADSL Lite). This is now
also added to the vdsl app for the vrx200.
Felix Fietkau [Mon, 7 Mar 2016 11:03:32 +0000 (11:03 +0000)]
ltq-adsl-app: sync annex option between from VDSL package
The adsl control app missed the activation of annex M and annex L in
the Annex A part, this now activates everything the firmware supports.
In Annex L type only the wide US (Mask1) was activated, now also the
narrow US (Mask2) version gets activated.
In addition annex J was also added.
Felix Fietkau [Mon, 7 Mar 2016 11:03:29 +0000 (11:03 +0000)]
base-files: change type of adsl and vdsl to dsl only
Instead of having two different types adsl and vdsl just create one dsl
type. This way we can use the same luci code for adsl and vdsl and the
config parameters are not so different.
Felix Fietkau [Mon, 7 Mar 2016 11:03:26 +0000 (11:03 +0000)]
ltq-vdsl-app: make the dsl_control application stop cleanly
I am not calling dsl_cmd because I want to ignore the lock, quit
should also be send when someone else is accessing it. I saw that some
other call was stuck here and all following calls were stuck in the
dsl_cmd lock.
projects / thirdparty / openwrt.git / log
