The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The nvme timeout handling doesn't do anything if the pci channel is
offline, which is the case when recovering from PCI error event, so it
was a bad idea to sync the controller reset in this state. This patch
flushes the reset work in the error_resume callback instead when the
channel is back to online. This keeps AER handling serialized and
can recover from timeouts.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199757 Fixes: cc1d5e749a2e ("nvme/pci: Sync controller reset for AER slot_reset") Reported-by: Alex Gagniuc <mr.nuke.me@gmail.com> Tested-by: Alex Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For any failure after nvme_rdma_start_queue in
nvme_rdma_configure_admin_queue, the admin queue will be freed with the
NVME_RDMA_Q_LIVE flag still set. Once nvme_rdma_stop_queue is invoked,
that will cause a use-after-free.
BUG: KASAN: use-after-free in rdma_disconnect+0x1f/0xe0 [rdma_cm]
To fix it, call nvme_rdma_stop_queue for all the failed cases after
nvme_rdma_start_queue.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com> Suggested-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two places report an error when a partition header is found to
not contain the right canary value. The error messages do not
properly byte swap the host ids. Fix this, and adjust the format
specificier to match the 16-bit unsigned data type.
Move the error handling for a bad canary value to the end of
qcom_smem_alloc_private(). This avoids some long lines, and
reduces the distraction of handling this unexpected problem.
Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there is at least one entry in the partition table, but no global
entry, the qcom_smem_set_global_partition() should return an error
just like it does if there are no partition table entries.
It turns out the function still returns an error in this case, but
it waits to do so until it has mistakenly treated the last entry in
the table as if it were the global entry found.
Fix the function to return immediately if no global entry is found
in the table.
Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In qmi_handle_init(), a buffer is allocated for to hold messages
received through the handle's socket. Any "normal" messages
(expected by the caller) will have a header prepended, so the
buffer size is adjusted to accomodate that.
The buffer must also be of sufficient size to receive control
messages, so the size is increased if necessary to ensure these
will fit.
Unfortunately the calculation is done wrong, making it possible
for the calculated buffer size to be too small to hold a "normal"
message. Specifically, if:
the current logic will use sizeof(struct qrtr_ctrl_pkt) as the
receive buffer size, which is not enough to hold the maximum
"normal" message plus its header. Currently this problem occurs
for (13 < recv_buf_size < 20).
This patch corrects this.
Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `s2idle_lock' is acquired during suspend while interrupts are
disabled even on RT. The lock is acquired for short sections only.
Make it a RAW lock which avoids "sleeping while atomic" warnings on RT.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under the following case, qgroup rescan can double account cowed tree
blocks:
In this case, extent tree only has one tree block.
-
| transid=5 last committed=4
| btrfs_qgroup_rescan_worker()
| |- btrfs_start_transaction()
| | transid = 5
| |- qgroup_rescan_leaf()
| |- btrfs_search_slot_for_read() on extent tree
| Get the only extent tree block from commit root (transid = 4).
| Scan it, set qgroup_rescan_progress to the last
| EXTENT/META_ITEM + 1
| now qgroup_rescan_progress = A + 1.
|
| fs tree get CoWed, new tree block is at A + 16K
| transid 5 get committed
-
| transid=6 last committed=5
| btrfs_qgroup_rescan_worker()
| btrfs_qgroup_rescan_worker()
| |- btrfs_start_transaction()
| | transid = 5
| |- qgroup_rescan_leaf()
| |- btrfs_search_slot_for_read() on extent tree
| Get the only extent tree block from commit root (transid = 5).
| scan it using qgroup_rescan_progress (A + 1).
| found new tree block beyong A, and it's fs tree block,
| account it to increase qgroup numbers.
-
In above case, tree block A, and tree block A + 16K get accounted twice,
while qgroup rescan should stop when it already reach the last leaf,
other than continue using its qgroup_rescan_progress.
Such case could happen by just looping btrfs/017 and with some
possibility it can hit such double qgroup accounting problem.
Fix it by checking the path to determine if we should finish qgroup
rescan, other than relying on next loop to exit.
Reported-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the code assumes that there's an implied barrier by the
sequence of code preceding the wakeup, namely the mutex unlock.
As Nikolay pointed out:
I think this is wrong (not your code) but the original assumption that
the RELEASE semantics provided by mutex_unlock is sufficient.
According to memory-barriers.txt:
Section 'LOCK ACQUISITION FUNCTIONS' states:
(2) RELEASE operation implication:
Memory operations issued before the RELEASE will be completed before the
RELEASE operation has completed.
Memory operations issued after the RELEASE *may* be completed before the
RELEASE operation has completed.
In btrfs_evict_inode(), if btrfs_truncate_inode_items() fails, the inode
item will still be in the tree but we still return the ino to the ino
cache. That will blow up later when someone tries to allocate that ino,
so don't return it to the cache.
Fixes: 581bb050941b ("Btrfs: Cache free inode numbers in memory") Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Omar Sandoval <osandov@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a buffer is queued or requeued in vb2_buffer_done, then don't
call the finish memop. In this case the buffer is only returned to vb2,
not to userspace.
Calling 'finish' here will cause an unbalance when the queue is
canceled, since the core will call the same memop again.
The current logic makes Smatch to false-detect a Spectre variant 1
vulnerability. The problem is that it initializes an u32 indirectly
from user space input.
After trying to write a fixup, after a while I realized that, in
practice, this shouldn't be a problem, as an u32 is initialized
from u8, but it took some time to discover it.
So, do some code cleanup to make it clearer for both humans
and machines about the valid range for "op".
Fix this warning:
drivers/media/cec/cec-pin-error-inj.c:170 cec_pin_error_inj_parse_line() warn: potential spectre issue 'pin->error_inj_args'
When the driver is configured in the "memcpy" dma-mode,
it uses vb2_vmalloc_memops, which is backed by a SLAB
allocator and so shouldn't be using GFP_DMA32.
RX Buffer Descriptor contains a VALID bit which indicates if the BD
is valid and has some data. This field is set by HNS3 hardware to
intimate the driver of some valid data present in the BD. nd should
be reset by the driver when BD is being used again. In the existing
code this bit was not being (re-)initialized properly and hence was
causing problems.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When register a RoCE client with hnae3vf device, it needs to judge
the device whether support RoCE vf function. Otherwise, it will
lead to calltrace when RoCE is not support vf function and remove
roce device.
the wl pointer can be null In case only wlcore_sdio is probed while
no WiLink module is successfully probed, as in the case of mounting a
wl12xx module while using a device tree file configured with wl18xx
related settings.
In this case the system was crashing in wl1271_suspend() as platform
device data is not set.
Make sure wl the pointer is valid before using it.
Signed-off-by: Eyal Reizer <eyalr@ti.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we cannot communicate with the EC chip to detect the protocol version
and its features, it's very likely useless to continue. Else we will
commit all kind of uninformed mistakes (using the wrong protocol, the
wrong buffer size, mixing the EC with other chips).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Acked-by: Benson Leung <bleung@chromium.org> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Gwendal Grignou <gwendal@chromium.org> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case, one BE is used by two FE1/FE2
FE1--->BE-->
|
FE2----]
when FE1/FE2 call dpcm_be_dai_hw_free() together
the BE users will be 2 (> 1), hence cannot be hw_free
the be state will leave at, ex. SND_SOC_DPCM_STATE_STOP
later FE1/FE2 call dpcm_be_dai_shutdown(),
will be skip due to wrong state.
leaving the BE not being hw_free and shutdown.
The BE dai will be hw_free later when calling
dpcm_be_dai_shutdown() if still in invalid state.
Signed-off-by: KaiChieh Chuang <kaichieh.chuang@mediatek.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the arm-cci driver is enabled, but both CONFIG_ARM_CCI5xx_PMU and
CONFIG_ARM_CCI400_PMU are not, we get a warning about how parts of
the driver are never used:
drivers/perf/arm-cci.c:1454:29: error: 'cci_pmu_models' defined but not used [-Werror=unused-variable]
drivers/perf/arm-cci.c:693:16: error: 'cci_pmu_event_show' defined but not used [-Werror=unused-function]
drivers/perf/arm-cci.c:685:16: error: 'cci_pmu_format_show' defined but not used [-Werror=unused-function]
Marking all three functions as __maybe_unused avoids the warnings in
randconfig builds. I'm doing this lacking any ideas for a better fix.
Fixes: 3de6be7a3dd8 ("drivers/bus: Split Arm CCI driver") Reviewed-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following warning during boot:
do not call blocking ops when !TASK_RUNNING; state=1 set at
[<(ptrval)>] qca_setup+0x194/0x750 [hci_uart]
WARNING: CPU: 2 PID: 1878 at kernel/sched/core.c:6135
__might_sleep+0x7c/0x88
In qca_set_baudrate(), the current task state is set to
TASK_UNINTERRUPTIBLE before going to sleep for 300ms. It was then
restored to TASK_INTERRUPTIBLE. This patch sets the current task state
back to TASK_RUNNING instead.
Currently, a BA session is opened when the tx traffic exceeds
10 frames per second. As a result of inter-op problems with some
APs, add a condition to open BA session only when station is
already authorized.
Fixes: 482e48440a0e ("iwlwifi: mvm: change open and close criteria of a BA session") Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the rx_allocator worker is canceled before running the
rx_init routine. rx_init frees and re-allocates all rxb's pages. The
rx_allocator worker also allocates pages for the used rxb's. Running
rx_init and rx_allocator simultaniously causes a kernel panic. Fix
that by canceling the work in rx_init.
[Problem description and how we fix it]
We should balance dirty metadata pages at the end of
btrfs_finish_ordered_io, since a small, unmergeable random write can
potentially produce dirty metadata which is multiple times larger than
the data itself. For example, a small, unmergeable 4KiB write may
produce:
16KiB dirty leaf (and possibly 16KiB dirty node) in subvolume tree
16KiB dirty leaf (and possibly 16KiB dirty node) in checksum tree
16KiB dirty leaf (and possibly 16KiB dirty node) in extent tree
Although we do call balance dirty pages in write side, but in the
buffered write path, most metadata are dirtied only after we reach the
dirty background limit (which by far only counts dirty data pages) and
wakeup the flusher thread. If there are many small, unmergeable random
writes spread in a large btree, we'll find a burst of dirty pages
exceeds the dirty_bytes limit after we wakeup the flusher thread - which
is not what we expect. In our machine, it caused out-of-memory problem
since a page cannot be dropped if it is marked dirty.
Someone may worry about we may sleep in btrfs_btree_balance_dirty_nodelay,
but since we do btrfs_finish_ordered_io in a separate worker, it will not
stop the flusher consuming dirty pages. Also, we use different worker for
metadata writeback endio, sleep in btrfs_finish_ordered_io help us throttle
the size of dirty metadata pages.
[Reproduce steps]
To reproduce the problem, we need to do 4KiB write randomly spread in a
large btree. In our 2GiB RAM machine:
1) Create 4 subvolumes.
2) Run fio on each subvolume:
3) Take snapshot on each subvolume and repeat fio on existing files.
4) Repeat step (3) until we get large btrees.
In our case, by observing btrfs_root_item->bytes_used, we have 2GiB of
metadata in each subvolume tree and 12GiB of metadata in extent tree.
5) Stop all fio, take snapshot again, and wait until all delayed work is
completed.
6) Start all fio. Few seconds later we hit OOM when the flusher starts
to work.
Driver switches vif sta_state into QTNF_STA_CONNECTING when cfg80211
core initiates connect procedure. Further this state is changed either
to QTNF_STA_CONNECTED or to QTNF_STA_DISCONNECTED by BSS_JOIN and
BSS_LEAVE events from firmware. However it is possible that no such
events will be sent by firmware, e.g. if EAPOL timed out.
In this case vif sta_mode will remain in QTNF_STA_CONNECTING state and
all subsequent connection attempts will fail with -EBUSY error code.
Fix this by perfroming STA state transition from QTNF_STA_CONNECTING
to QTNF_STA_DISCONNECTED in cfg80211 disconnect callback.
No need to rely upon firmware events in this case.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We were picking up the wrong header should use asm/ioctls.h form the kernel
and not the header from the system (sys/ioctl.h). In the current code we
added the correct include and we added the kernel headers path to the CFLAGS.
When devpts_pts test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as
a fail by the Kselftest framework. This leads to false negative
result even when the test could not be run.
In another case, it returns pass for a skipped test reporting a false
postive.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Change it to use ksft_exit_skip() when test is skipped.
When intel_pstate test is skipped because of unmet dependencies and/or
unsupported configuration, it returns 0 which is treated as a pass
by the Kselftest framework. This leads to false positive result even
when the test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
When kvm test is skipped because of unmet dependencies and/or unsupported
configuration, it exits with error which is treated as a fail by the
Kselftest framework. This leads to false negative result even when the test
could not be run.
Change it to return kselftest skip code when a test gets skipped to clearly
report that the test could not be run.
Change it to use ksft_exit_skip() when the test is skipped. In addition,
refine test_assert() message to include strerror() string and add explicit
check for EACCES to cleary identify when test doesn't run when access is
denied to resources required e.g: open /dev/kvm failed, rc: -1 errno: 13
When memfd test is skipped because of unmet dependencies and/or unsupported
configuration, it returns non-zero value which is treated as a fail by the
Kselftest framework. This leads to false negative result even when the test
could not be run.
Change it to return kselftest skip code when a test gets skipped to clearly
report that the test could not be run.
Added an explicit check for root user at the start of memfd hugetlbfs test
and return skip code if a non-root user attempts to run it.
In addition, return skip code when not enough huge pages are available to
run the test.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
A few changes improve the overall usability of the test:
* fix a hard-coded maximum frequency (3300),
* don't adjust the CPU frequency if only evaluating results,
* fix a comparison for multiple frequencies.
A symptom of that last issue looked like this:
./run.sh: line 107: [: too many arguments
./run.sh: line 110: 3099
3099
3100-3100: syntax error in expression (error token is \"3099
3100-3100\")
Because a check will count how many differente frequencies
there are among the CPUs of the system, and after they are
tallied another read is performed, which might produce
different results.
For Nehalem and Westmere, there is only one fixed counter for W-Box.
There is no index which is bigger than UNCORE_PMC_IDX_FIXED.
It is not correct to use >= to check fixed counter.
The code quality issue will bring problem when new counter index is
introduced.
Signed-off-by: Kan Liang <kan.liang@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: acme@kernel.org Cc: eranian@google.com Link: http://lkml.kernel.org/r/1525371913-10597-2-git-send-email-kan.liang@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no index which is bigger than UNCORE_PMC_IDX_FIXED. The only
exception is client IMC uncore, which has been specially handled.
For generic code, it is not correct to use >= to check fixed counter.
The code quality issue will bring problem when a new counter index is
introduced.
Signed-off-by: Kan Liang <kan.liang@intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: acme@kernel.org Cc: eranian@google.com Link: http://lkml.kernel.org/r/1525371913-10597-3-git-send-email-kan.liang@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the amount of available ports varies by the kernels build
configuration. To remove the limitation of the fixed 128 ports
we allocate the amount of idevs by using the number we get
from the kernel.
detach_port() fails to call usbip_vhci_driver_close() from its error
path after usbip_vhci_detach_device() returns failure, leaking memory
allocated in usbip_vhci_driver_open() and holding udev_context and udev
references. Fix it to call usbip_vhci_driver_close().
In bfq_requests_merged(), there is a deadlock because the lock on
bfqq->bfqd->lock is held by the calling function, but the code of
this function tries to grab the lock again.
This deadlock is currently hidden by another bug (fixed by next commit
for this source file), which causes the body of bfq_requests_merged()
to be never executed.
This commit removes the deadlock by removing the lock/unlock pair.
After revoking atomic write, related LBA can be reused by others, so we
need to wait page writeback before reusing the LBA, in order to avoid
interference between old atomic written in-flight IO and new IO.
With data_flush mount option, during recovery, in order to avoid entering
above writeback flow, let's detect recovery status and do skip in
f2fs_balance_fs_bg.
Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Yunlei He <heyunlei@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following patch disables loading of f2fs module on architectures
which have PAGE_SIZE > 4096 , since it is impossible to mount f2fs on
such architectures , log messages are:
mount: /mnt: wrong fs type, bad option, bad superblock on
/dev/vdiskb1, missing codepage or helper program, or other error.
/dev/vdiskb1: F2FS filesystem,
UUID=1d8b9ca4-2389-4910-af3b-10998969f09c, volume name ""
May 15 18:03:13 ttip kernel: F2FS-fs (vdiskb1): Invalid
page_cache_size (8192), supports only 4KB
May 15 18:03:13 ttip kernel: F2FS-fs (vdiskb1): Can't find valid F2FS
filesystem in 1th superblock
May 15 18:03:13 ttip kernel: F2FS-fs (vdiskb1): Invalid
page_cache_size (8192), supports only 4KB
May 15 18:03:13 ttip kernel: F2FS-fs (vdiskb1): Can't find valid F2FS
filesystem in 2th superblock
May 15 18:03:13 ttip kernel: F2FS-fs (vdiskb1): Invalid
page_cache_size (8192), supports only 4KB
If the server recalls the layout that was just handed out, we risk hitting
a race as described in RFC5661 Section 2.10.6.3 unless we ensure that we
release the sequence slot after processing the LAYOUTGET operation that
was sent as part of the OPEN compound.
When cleaning up buffer entries as we wrap up, their state should be
"completed". If any of the entries is in "submitted" state, it means
that something bad has happened. Trigger a warning immediately instead of
waiting for the state flag to eventually be updated, thus hiding the
issue.
Currently in case of error caused by bio_pc_add_page in
pblk_bio_add_pages two issues occur when calling from
pblk_rb_read_to_bio(). First one is in pblk_bio_free_pages, since we
are trying to free pages not allocated from our mempool. Second one
is the warn from dma_pool_free, that we are trying to free NULL
pointer dma.
When hclge_ae_stop is called during resetting, it will cancel the
service_task by calling cancel_work_sync, which may cause the
service_task to exit without clearing HCLGE_STATE_SERVICE_SCHED
bit. If this happens, the service_task will never run again.
This patch fixes this problem by clearing it after calling
cancel_work_sync in hclge_ae_stop.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When resetting, phy_state_machine may be accessing the phy through
firmware if the phy is not stopped or disconnected, which will
cause firemware timeout problem because the firmware is busy
processing the reset request.
This patch fixes it by disabling the phy when resetting.
Fixes: b940aeae0ed6 ("net: hns3: never send command queue message to IMP when reset") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The si544 driver had a rounding problem that using the result of clk_round_rate
may set the clock to yet another rate, for example:
clk_round_rate(195000000) = 194999999
clk_round_rate(194999999) = 194999998
Clients would expect that after clk_set_rate(clk, freq2=clk_round_rate(clk, freq)) the
chip will be running at exactly freq2.
The problem was in the calculation of the feedback divider, it was always rounded
down instead of to the nearest possible VCO value.
After this change, the following holds true for any supported frequency:
actual_freq = clk_round_rate(clk, freq);
clk_set_rate(clk, actual_freq);
clk_round_rate(clk, actual_freq) == actual_freq && clk_get_rate(clk) == actual_freq
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Fixes: 953cc3e81170 ("clk: Add driver for the si544 clock generator chip") Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stores to update the SLB shadow area must be made as they appear
in the C code, so that the hypervisor does not see an entry with
mismatched vsid and esid. Use WRITE_ONCE for this.
GCC has been observed to elide the first store to esid in the update,
which means that if the hypervisor interrupts the guest after storing
to vsid, it could see an entry with old esid and new vsid, which may
possibly result in memory corruption.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
time_init() will set up tb_ticks_per_usec based on reality.
time_init() is called *after* udbg_init_opal_common() during boot.
from arch/powerpc/kernel/time.c:
unsigned long tb_ticks_per_usec = 100; /* sane default */
Currently, all powernv systems have a timebase frequency of 512mhz
(512000000/1000000 == 0x200) - although there's nothing written
down anywhere that I can find saying that we couldn't make that
different based on the requirements in the ISA.
So, we've been (accidentally) thwacking the (currently) correct
(for powernv at least) value for tb_ticks_per_usec earlier than
we otherwise would have.
The "sane default" seems to be adequate for our purposes between
udbg_init_opal_common() and time_init() being called, and if it isn't,
then we should probably be setting it somewhere that isn't hvc_opal.c!
Signed-off-by: Stewart Smith <stewart@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct two cases where eeh_pcid_get() is used to reference the driver's
module but the reference is dropped before the driver pointer is used.
In eeh_rmv_device() also refactor a little so that only two calls to
eeh_pcid_put() are needed, rather than three and the reference isn't
taken at all if it wasn't needed.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A no-op form of ori (or immediate of 0 into r31 and the result stored
in r31) has been re-tasked as a speculation barrier. The instruction
only acts as a barrier on newer machines with appropriate firmware
support. On older CPUs it remains a harmless no-op.
Implement barrier_nospec using this instruction.
mpe: The semantics of the instruction are believed to be that it
prevents execution of subsequent instructions until preceding branches
have been fully resolved and are no longer executing speculatively.
There is no further documentation available at this time.
Signed-off-by: Michal Suchanek <msuchanek@suse.de> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87a156fb18fe1 ("Align hot loops of some string functions")
degraded the performance of string functions by adding useless
nops
A simple benchmark on an 8xx calling 100000x a memchr() that
matches the first byte runs in 41668 TB ticks before this patch
and in 35986 TB ticks after this patch. So this gives an
improvement of approx 10%
Another benchmark doing the same with a memchr() matching the 128th
byte runs in 1011365 TB ticks before this patch and 1005682 TB ticks
after this patch, so regardless on the number of loops, removing
those useless nops improves the test by 5683 TB ticks.
Fixes: 87a156fb18fe1 ("Align hot loops of some string functions") Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There have been multiple reports of crashes that look like
kernel: RIP: 0010:[<ffffffff8110303f>] timecounter_read+0xf/0x50
[...]
kernel: Call Trace:
kernel: [<ffffffffa0806b0f>] e1000e_phc_gettime+0x2f/0x60 [e1000e]
kernel: [<ffffffffa0806c5d>] e1000e_systim_overflow_work+0x1d/0x80 [e1000e]
kernel: [<ffffffff810992c5>] process_one_work+0x155/0x440
kernel: [<ffffffff81099e16>] worker_thread+0x116/0x4b0
kernel: [<ffffffff8109f422>] kthread+0xd2/0xf0
kernel: [<ffffffff8163184f>] ret_from_fork+0x3f/0x70
These can be traced back to the fact that e1000e_systim_reset() skips the
timecounter_init() call if e1000e_get_base_timinca() returns -EINVAL, which
leads to a null deref in timecounter_read().
Commit 83129b37ef35 ("e1000e: fix systim issues", v4.2-rc1) reworked
e1000e_get_base_timinca() in such a way that it can return -EINVAL for
e1000_pch_spt if the SYSCFI bit is not set in TSYNCRXCTL.
Some experimentation has shown that on I219 (e1000_pch_spt, "MAC: 12")
adapters, the E1000_TSYNCRXCTL_SYSCFI flag is unstable; TSYNCRXCTL reads
sometimes don't have the SYSCFI bit set. Retrying the read shortly after
finds the bit to be set. This was observed at boot (probe) but also link up
and link down.
Moreover, the phc (PTP Hardware Clock) seems to operate normally even after
reads where SYSCFI=0. Therefore, remove this register read and
unconditionally set the clock parameters.
KASAN found an UAF in ceph_statfs. This was a one-off bug but looking at
the code it looks like the monmap access needs to be protected as it can
be modified while we're accessing it. Fix this by protecting the access
with the monc->mutex.
BUG: KASAN: use-after-free in ceph_statfs+0x21d/0x2c0
Read of size 8 at addr ffff88006844f2e0 by task trinity-c5/304
The names for BPF_ALU64 | BPF_ARSH are emit_a32_arsh_*,
the names for BPF_ALU64 | BPF_LSH are emit_a32_lsh_*, but
the names for BPF_ALU64 | BPF_RSH are emit_a32_lsr_*.
For consistence reason, let's rename emit_a32_lsr_* to
emit_a32_rsh_*.
Drop the in_nmi() check from printk_safe_flush_on_panic()
and attempt to re-init (IOW unlock) locked logbuf spinlock
from panic CPU regardless of its context.
Otherwise, theoretically, we can deadlock on logbuf trying to flush
per-CPU buffers:
a) Panic CPU is running in non-NMI context
b) Panic CPU sends out shutdown IPI via reboot vector
c) Panic CPU fails to stop all remote CPUs
d) Panic CPU sends out shutdown IPI via NMI vector
One of the CPUs that we bring down via NMI vector can hold
logbuf spin lock (theoretically).
Link: http://lkml.kernel.org/r/20180530070350.10131-1-sergey.senozhatsky@gmail.com
To: Steven Rostedt <rostedt@goodmis.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TW9910 PDN gpio (power down) is listed as active high in the chip
manual. It turns out it is actually active low as when set to physical
level 0 it actually turns the video decoder power off.
Without this patch applied:
tw9910 0-0045: Product ID error 1f:2
With this patch applied:
tw9910 0-0045: tw9910 Product ID b:0
The DA9063 watchdog has only one register field to store the timeout value
and to enable the watchdog. The watchdog gets enabled if the value is
not zero. There is no issue if the watchdog is already running but it
leads into problems if the watchdog is disabled.
If the watchdog is disabled and only the timeout value should be prepared
the watchdog gets enabled too. Add a check to get the current watchdog
state and update the watchdog timeout value on hw-side only if the
watchdog is already active.
When listing sets with timeout support, there's a probability that
just timing out entries with "0" timeout value is listed/saved.
However when restoring the saved list, the zero timeout value means
permanent elelements.
The new behaviour is that timing out entries are listed with "timeout 1"
instead of zero.
Userspace `ipset` command forbids family option for hash:mac type:
ipset create test hash:mac family inet4
ipset v6.30: Unknown argument: `family'
However, this check is not done in kernel itself. When someone use
external netlink applications (pyroute2 python library for example), one
can create hash:mac with invalid family and inconsistant results from
userspace (`ipset` command cannot read set content anymore).
This patch enforce the logic in kernel, and forbids insertion of
hash:mac with a family set.
Since IP_SET_PROTO_UNDEF is defined only for hash:mac, this patch has no
impact on other hash:* sets
The reason is that the event_pmu is too strong
and match also single string. Changing it to
force the '/' separators to be part of the rule,
and getting the proper error now:
$ perf stat -e inst kill
event syntax error: 'inst'
\___ parser error
Run 'perf list' for a list of valid events
...
Suggested-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20180605121416.31645-1-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the VF frequently switches the CMDQ interrupt, if the CMDQ_SRC is not
cleared, the VF will not receive the new PF response after the interrupt
is re-enabled, the corresponding log is as follows:
[ 317.482222] hns3 0000:00:03.0: VF could not get mbx resp(=0) from PF
in 500 tries
[ 317.483137] hns3 0000:00:03.0: VF request to get tqp info from PF
failed -5
This patch fixes this problem by clearing CMDQ_SRC before enabling
interrupt and syncing pending IRQ handlers after disabling interrupt.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by: Xi Wang <wangxi11@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When retransmitting the final ACK or ABORT packet for a call, the cid field
in the packet header is set to the connection's cid, but this is incorrect
as it also needs to include the channel number on that connection that the
call was made on.
works around. I'm not intending to revert that as it will help protect
against problems that might occur on the server.
Fixes: 3136ef49a14c ("rxrpc: Delay terminal ACK transmission on a client call") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using RTC_ALM_SET or RTC_WKALM_SET with rtc_wkalrm.enabled not set,
rtc_timer_enqueue() is not called and rtc_set_alarm() may succeed but the
subsequent RTC_AIE_ON ioctl will fail. RTC_ALM_READ would also fail in that
case.
Ensure rtc_set_alarm() fails when alarms are not supported to avoid letting
programs think the alarms are working for a particular RTC when they are
not.
Currently, __vunmap flow is,
1) Release the VM area
2) Free the debug objects corresponding to that vm area.
This leave some race window open.
1) Release the VM area
1.5) Some other client gets the same vm area
1.6) This client allocates new debug objects on the same
vm area
2) Free the debug objects corresponding to this vm area.
Here, we actually free 'other' client's debug objects.
Fix this by freeing the debug objects first and then releasing the VM
area.
In commit ab676b7d6fbf ("pagemap: do not leak physical addresses to
non-privileged userspace"), the /proc/PID/pagemap is restricted to be
readable only by CAP_SYS_ADMIN to address some security issue.
In commit 1c90308e7a77 ("pagemap: hide physical addresses from
non-privileged users"), the restriction is relieved to make
/proc/PID/pagemap readable, but hide the physical addresses for
non-privileged users.
But the swap entries are readable for non-privileged users too. This
has some security issues. For example, for page under migrating, the
swap entry has physical address information. So, in this patch, the
swap entries are hided for non-privileged users too.
Link: http://lkml.kernel.org/r/20180508012745.7238-1-ying.huang@intel.com Fixes: 1c90308e7a77 ("pagemap: hide physical addresses from non-privileged users") Signed-off-by: "Huang, Ying" <ying.huang@intel.com> Suggested-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Andrei Vagin <avagin@openvz.org> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Daniel Colascione <dancol@google.com> Cc: Zi Yan <zi.yan@cs.rutgers.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LKP robot found a 27% will-it-scale/page_fault3 performance
regression regarding commit e27be240df53("mm: memcg: make sure
memory.events is uptodate when waking pollers").
What the test does is:
1 mkstemp() a 128M file on a tmpfs;
2 start $nr_cpu processes, each to loop the following:
2.1 mmap() this file in shared write mode;
2.2 write 0 to this file in a PAGE_SIZE step till the end of the file;
2.3 unmap() this file and repeat this process.
3 After 5 minutes, check how many loops they managed to complete, the
higher the better.
The commit itself looks innocent enough as it merely changed some event
counting mechanism and this test didn't trigger those events at all.
Perf shows increased cycles spent on accessing root_mem_cgroup->stat_cpu
in count_memcg_event_mm()(called by handle_mm_fault()) and in
__mod_memcg_state() called by page_add_file_rmap(). So it's likely due
to the changed layout of 'struct mem_cgroup' that either make stat_cpu
falling into a constantly modifying cacheline or some hot fields stop
being in the same cacheline.
I verified this by moving memory_events[] back to where it was:
Later investigation found that as long as the following 3 fields
moving_account, move_lock_task and stat_cpu are in the same cacheline,
performance will be good. To avoid future performance surprise by other
commits changing the layout of 'struct mem_cgroup', this patch makes
sure the 3 fields stay in the same cacheline.
One concern of this approach is, moving_account and move_lock_task could
be modified when a process changes memory cgroup while stat_cpu is a
always read field, it might hurt to place them in the same cacheline. I
assume it is rare for a process to change memory cgroup so this should
be OK.
Link: https://lkml.kernel.org/r/20180528114019.GF9904@yexl-desktop Link: http://lkml.kernel.org/r/20180601071115.GA27302@intel.com Signed-off-by: Aaron Lu <aaron.lu@intel.com> Reported-by: kernel test robot <xiaolong.ye@intel.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reporting an AB-BA deadlock like shown above, it would be nice if
trace of PID=6541 is printed as well as trace of PID=6540 before calling
panic().
Showing hung tasks up to /proc/sys/kernel/hung_task_warnings could delay
calling panic() but normally there should not be so many hung tasks.
MAP_DMA ioctls might be called from various threads within a process,
for example when using QEMU, the vCPU threads are often generating
these calls and we therefore take a reference to that vCPU task.
However, QEMU also supports vCPU hotplug on some machines and the task
that called MAP_DMA may have exited by the time UNMAP_DMA is called,
resulting in the mm_struct pointer being NULL and thus a failure to
match against the existing mapping.
To resolve this, we instead take a reference to the thread
group_leader, which has the same mm_struct and resource limits, but
is less likely exit, at least in the QEMU case. A difficulty here is
guaranteeing that the capabilities of the group_leader match that of
the calling thread, which we resolve by tracking CAP_IPC_LOCK at the
time of calling rather than at an indeterminate time in the future.
Potentially this also results in better efficiency as this is now
recorded once per MAP_DMA ioctl.
When we create an mdev device, we check for duplicates against the
parent device and return -EEXIST if found, but the mdev device
namespace is global since we'll link all devices from the bus. We do
catch this later in sysfs_do_create_link_sd() to return -EEXIST, but
with it comes a kernel warning and stack trace for trying to create
duplicate sysfs links, which makes it an undesirable response.
Therefore we should really be looking for duplicates across all mdev
parent devices, or as implemented here, against our mdev device list.
Using mdev_list to prevent duplicates means that we can remove
mdev_parent.lock, but in order not to serialize mdev device creation
and removal globally, we add mdev_device.active which allows UUIDs to
be reserved such that we can drop the mdev_list_lock before the mdev
device is fully in place.
Two behavioral notes; first, mdev_parent.lock had the side-effect of
serializing mdev create and remove ops per parent device. This was
an implementation detail, not an intentional guarantee provided to
the mdev vendor drivers. Vendor drivers can trivially provide this
serialization internally if necessary. Second, review comments note
the new -EAGAIN behavior when the device, and in particular the remove
attribute, becomes visible in sysfs. If a remove is triggered prior
to completion of mdev_device_create() the user will see a -EAGAIN
error. While the errno is different, receiving an error during this
period is not, the previous implementation returned -ENODEV for the
same condition. Furthermore, the consistency to the user is improved
in the case where mdev_device_remove_ops() returns error. Previously
concurrent calls to mdev_device_remove() could see the device
disappear with -ENODEV and return in the case of error. Now a user
would see -EAGAIN while the device is in this transitory state.
Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Acked-by: Halil Pasic <pasic@linux.ibm.com> Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running a fuzz tester against a KASAN-enabled kernel, the following
splat periodically occurs.
The problem occurs when the test sends a GETDEVICEINFO request with a
malformed xdr array (size but no data) for gdia_notify_types and the
array size is > 0x3fffffff, which results in an overflow in the value of
nbytes which is passed to read_buf().
If the array size is 0x40000000, 0x80000000, or 0xc0000000, then after
the overflow occurs, the value of nbytes 0, and when that happens the
pointer returned by read_buf() points to the end of the xdr data (i.e.
argp->end) when really it should be returning NULL.
Fix this by returning NFS4ERR_BAD_XDR if the array size is > 1000 (this
value is arbitrary, but it's the same threshold used by
nfsd4_decode_bitmap()... in could really be any value >= 1 since it's
expected to get at most a single bitmap in gdia_notify_types).
[ 119.256854] ==================================================================
[ 119.257611] BUG: KASAN: use-after-free in nfsd4_decode_getdeviceinfo+0x5a4/0x5b0 [nfsd]
[ 119.258422] Read of size 4 at addr ffff880113ada000 by task nfsd/538
I noticed a memory corruption crash in nfsd in
4.17-rc1. This patch corrects the issue.
Fix to return error if the delegation couldn't be hashed or there was
a recall in progress. Use the existing error path instead of
destroy_delegation() for readability.
Signed-off-by: Andrew Elble <aweits@rit.edu> Fixes: 353601e7d323c ("nfsd: create a separate lease for each delegation") Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the server returns NFS4ERR_SEQ_FALSE_RETRY or NFS4ERR_RETRY_UNCACHED_REP,
then it thinks we're trying to replay an existing request. If so, then
let's just bump the sequence ID and retry the operation.
When we were enabling macvlan interfaces we weren't correctly configuring
things until ixgbe_setup_tc was called a second time either by tweaking the
number of queues or increasing the macvlan count past 15.
The issue came down to the fact that num_rx_pools is not populated until
after the queues and interrupts are reinitialized.
Instead of trying to set it sooner we can just move the call to setup at
least 1 traffic class to the SR-IOV/VMDq setup function so that we just set
it for this one case. We already had a spot that was configuring the queues
for TC 0 in the code here anyway so it makes sense to also set the number
of TCs here as well.
Fixes: 49cfbeb7a95c ("ixgbe: Fix handling of macvlan Tx offload") Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, when IO to DS fails, client returns the layout and
retries against the MDS. However, then on umounting (inode eviction)
it returns the layout again.
This is because pnfs_return_layout() was changed in
commit d78471d32bb6 ("pnfs/blocklayout: set PNFS_LAYOUTRETURN_ON_ERROR")
to always set NFS_LAYOUT_RETURN_REQUESTED so even if we returned
the layout, it will be returned again. Instead, let's also check
if we have already marked the layout invalid.
The max number of slots used in xennet_get_responses() is set to
MAX_SKB_FRAGS + (rx->status <= RX_COPY_THRESHOLD).
In old kernel-xen MAX_SKB_FRAGS was 18, while nowadays it is 17. This
difference is resulting in frequent messages "too many slots" and a
reduced network throughput for some workloads (factor 10 below that of
a kernel-xen based guest).
Replacing MAX_SKB_FRAGS by XEN_NETIF_NR_SLOTS_MIN for calculation of
the max number of slots to use solves that problem (tests showed no
more messages "too many slots" and throughput was as high as with the
kernel-xen based guest system).
Replace MAX_SKB_FRAGS-2 by XEN_NETIF_NR_SLOTS_MIN-1 in
netfront_tx_slot_available() for making it clearer what is really being
tested without actually modifying the tested value.
Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
