The current sun6i SPI implementation initializes the transfer too early,
resulting in SCK going high before the transfer. When using an additional
(gpio) chipselect with sun6i, the chipselect is asserted at a time when
clock is high, making the SPI transfer fail.
This is due to SUN6I_GBL_CTL_BUS_ENABLE being written into
SUN6I_GBL_CTL_REG at an early stage. Moving that to the transfer
function, hence, right before the transfer starts, mitigates that
problem.
Rename struct sms_msg_data4 to sms_msg_data5 and increase the size of
its msg_data array from 4 to 5 elements. Notice that at some point
the 5th element of msg_data is being accessed in function
smscore_load_firmware_family2():
1006 trigger_msg->msg_data[4] = 4; /* Task ID */
Also, there is no need for the object _trigger_msg_ of type struct
sms_msg_data *, when _msg_ can be used, directly. Notice that msg_data
in struct sms_msg_data is a one-element array, which causes multiple
out-of-bounds warnings when accessing beyond its first element
in function smscore_load_firmware_family2():
the out-of-bounds warnings are actually valid and should be addressed.
Fix this by declaring object _msg_ of type struct sms_msg_data5 *,
which contains a 5-elements array, instead of just 4. And use
_msg_ directly, instead of creating object trigger_msg.
This helps with the ongoing efforts to enable -Warray-bounds by fixing
the following warnings:
CC [M] drivers/media/common/siano/smscoreapi.o
drivers/media/common/siano/smscoreapi.c: In function ‘smscore_load_firmware_family2’:
drivers/media/common/siano/smscoreapi.c:1003:24: warning: array subscript 1 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
1003 | trigger_msg->msg_data[1] = 6; /* Priority */
| ~~~~~~~~~~~~~~~~~~~~~^~~
In file included from drivers/media/common/siano/smscoreapi.c:12:
drivers/media/common/siano/smscoreapi.h:619:6: note: while referencing ‘msg_data’
619 | u32 msg_data[1];
| ^~~~~~~~
drivers/media/common/siano/smscoreapi.c:1004:24: warning: array subscript 2 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
1004 | trigger_msg->msg_data[2] = 0x200; /* Stack size */
| ~~~~~~~~~~~~~~~~~~~~~^~~
In file included from drivers/media/common/siano/smscoreapi.c:12:
drivers/media/common/siano/smscoreapi.h:619:6: note: while referencing ‘msg_data’
619 | u32 msg_data[1];
| ^~~~~~~~
drivers/media/common/siano/smscoreapi.c:1005:24: warning: array subscript 3 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
1005 | trigger_msg->msg_data[3] = 0; /* Parameter */
| ~~~~~~~~~~~~~~~~~~~~~^~~
In file included from drivers/media/common/siano/smscoreapi.c:12:
drivers/media/common/siano/smscoreapi.h:619:6: note: while referencing ‘msg_data’
619 | u32 msg_data[1];
| ^~~~~~~~
drivers/media/common/siano/smscoreapi.c:1006:24: warning: array subscript 4 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
1006 | trigger_msg->msg_data[4] = 4; /* Task ID */
| ~~~~~~~~~~~~~~~~~~~~~^~~
In file included from drivers/media/common/siano/smscoreapi.c:12:
drivers/media/common/siano/smscoreapi.h:619:6: note: while referencing ‘msg_data’
619 | u32 msg_data[1];
| ^~~~~~~~
Fixes: 018b0c6f8acb ("[media] siano: make load firmware logic to work with newer firmwares") Co-developed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the CSI bps per lane is not in the valid range, an appropriate error
code -EINVAL should be returned. However, we currently do not explicitly
assign this error code to 'ret'. As a result, 0 was incorrectly returned.
Fixes: 256148246852 ("[media] tc358743: support probe from device tree") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Propagate the error code
upstream, as it should have been done from the start...
Iff platform_get_irq() fails (or returns IRQ0) and thus the polling mode
has to be used, ata_host_activate() hits the WARN_ON() due to 'irq_handler'
parameter being non-NULL if the polling mode is selected. Let's only set
the pointer to the driver's IRQ handler if platform_get_irq() returns a
valid IRQ # -- this should avoid the unnecessary WARN_ON()...
The use of an enum named 'RST' conflicts with a #define macro
named 'RST' in arch/mips/include/asm/mach-rc32434/rb.h.
The MIPS use of RST was there first (AFAICT), so change the
media/i2c/ uses of RST to be named 'RSET'.
'git grep -w RSET' does not report any naming conflicts with the
new name.
This fixes multiple build errors:
arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
drivers/media/i2c/s5c73m3/s5c73m3.h:356:2: note: in expansion of macro 'RST'
356 | RST,
| ^~~
../arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
../drivers/media/i2c/s5k6aa.c:180:2: note: in expansion of macro 'RST'
180 | RST,
| ^~~
../arch/mips/include/asm/mach-rc32434/rb.h:15:14: error: expected identifier before '(' token
15 | #define RST (1 << 15)
| ^
../drivers/media/i2c/s5k5baf.c:238:2: note: in expansion of macro 'RST'
238 | RST,
| ^~~
and some others that I have trimmed.
Fixes: cac47f1822fc ("[media] V4L: Add S5C73M3 camera driver") Fixes: 8b99312b7214 ("[media] Add v4l2 subdev driver for S5K4ECGX sensor") Fixes: 7d459937dc09 ("[media] Add driver for Samsung S5K5BAF camera sensor") Fixes: bfa8dd3a0524 ("[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Cc: Sangwook Lee <sangwook.lee@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver overrides the error codes returned by platform_get_irq() to
-ENOENT, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Switch to propagating the
error code upstream, still checking/overriding IRQ0 as libata regards it
as "no IRQ" (thus polling) anyway...
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Switch to propagating the
error code upstream, still checking/overriding IRQ0 as libata regards it
as "no IRQ" (thus polling) anyway...
Testing ixp4xx_crypto with CONFIG_DMA_API_DEBUG lead to the following error:
DMA-API: platform ixp4xx_crypto.0: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=24 bytes]
gcc points out a mistake in the mca driver that goes back to before the
git history:
arch/ia64/kernel/mca_drv.c: In function 'init_record_index_pools':
arch/ia64/kernel/mca_drv.c:346:54: error: expression does not compute the number of elements in this array; element typ
e is 'int', not 'size_t' {aka 'long unsigned int'} [-Werror=sizeof-array-div]
346 | for (i = 1; i < sizeof sal_log_sect_min_sizes/sizeof(size_t); i++)
| ^
This is the same as sizeof(size_t), which is two shorter than the actual
array. Use the ARRAY_SIZE() macro to get the correct calculation instead.
Although the system will not be in a good condition or it will not
boot if acpi_bus_init() fails, it is still necessary to put the
kobject in the error path before returning to avoid leaking memory.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
include/linux/prandom.h:114:45: sparse: sparse: cast truncates bits from
constant value
This is because the 64-bit seed value is manipulated and then placed in a
u32, causing an implicit cast and truncation. A forced cast to u32 doesn't
prevent this warning, which is reasonable because a typecast doesn't prove
that truncation was expected.
Logical-AND the value with 0xffffffff to make explicit that truncation to
32-bit is intended.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Petr Mladek <pmladek@suse.com> Link: https://lore.kernel.org/r/20210525122012.6336-3-rf@opensource.cirrus.com Signed-off-by: Sasha Levin <sashal@kernel.org>
These rx tx flags arguments are for signaling close_connection() from
which worker they are called. Obviously the receive worker cannot cancel
itself and vice versa for swork. For the othercon the receive worker
should only be used, however to avoid deadlocks we should pass the same
flags as the original close_connection() was called.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
block_dump is an old debugging interface, one of it's functions is used
to print the information about who write which file on disk. If we
enable block_dump through /proc/sys/vm/block_dump and turn on debug log
level, we can gather information about write process name, target file
name and disk from kernel message. This feature is realized in
block_dump___mark_inode_dirty(), it print above information into kernel
message directly when marking inode dirty, so it is noisy and can easily
trigger log storm. At the same time, get the dentry refcount is also not
safe, we found it will lead to deadlock on ext4 file system with
data=journal mode.
After tracepoints has been introduced into the kernel, we got a
tracepoint in __mark_inode_dirty(), which is a better replacement of
block_dump___mark_inode_dirty(). The only downside is that it only trace
the inode number and not a file name, but it probably doesn't matter
because the original printed file name in block_dump is not accurate in
some cases, and we can still find it through the inode number and device
id. So this patch delete the dirting inode part of block_dump feature.
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20210313030146.2882027-2-yi.zhang@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Generally, the C-state latency is provided by the _CST method or
FADT, but some OEM platforms using AMD Picasso, Renoir, Van Gogh,
and Cezanne set the C2 latency greater than C3's which causes the
C2 state to be skipped.
That will block the core entering PC6, which prevents S0ix working
properly on Linux systems.
In other operating systems, the latency values are not validated and
this does not cause problems by skipping states.
To avoid this issue on Linux, detect when latencies are not an
arithmetic progression and sort them.
With a config having PAGE_SIZE set to 256K, BTRFS build fails
with the following message
include/linux/compiler_types.h:326:38: error: call to
'__compiletime_assert_791' declared with attribute error:
BUILD_BUG_ON failed: (BTRFS_MAX_COMPRESSED % PAGE_SIZE) != 0
BTRFS_MAX_COMPRESSED being 128K, BTRFS cannot support platforms with
256K pages at the time being.
There are two platforms that can select 256K pages:
- hexagon
- powerpc
Disable BTRFS when 256K page size is selected. Supporting this would
require changes to the subpage mode that's currently being developed.
Given that 256K is many times larger than page sizes commonly used and
for what the algorithms and structures have been tuned, it's out of
scope and disabling build is a reasonable option.
The risk of especulation is actually almost-non-existing here,
as there are very few users of TCP/IP using the DVB stack,
as, this is mainly used with DVB-S/S2 cards, and only by people
that receives TCP/IP from satellite connections, which limits
a lot the number of users of such feature(*).
(*) In thesis, DVB-C cards could also benefit from it, but I'm
yet to see a hardware that supports it.
crypto_shash_alg_has_setkey() is implemented by testing whether the
.setkey() member of a struct shash_alg points to the default version,
called shash_no_setkey(). As crypto_shash_alg_has_setkey() is a static
inline, this requires shash_no_setkey() to be exported to modules.
Unfortunately, when building with CFI, function pointers are routed
via CFI stubs which are private to each module (or to the kernel proper)
and so this function pointer comparison may fail spuriously.
Let's fix this by turning crypto_shash_alg_has_setkey() into an out of
line function.
Cc: Sami Tolvanen <samitolvanen@google.com> Cc: Eric Biggers <ebiggers@kernel.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Reviewed-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
In 'bt878_irq', the driver calls 'tasklet_schedule', but this tasklet is
set in 'dvb_bt8xx_load_card' of another driver 'dvb-bt8xx'.
However, this two drivers are separate. The user may not load the
'dvb-bt8xx' driver when loading the 'bt8xx' driver, that is, the tasklet
has not been initialized when 'tasklet_schedule' is called, so it is
necessary to check whether the tasklet is initialized in 'bt878_probe'.
Fix this by adding a check at the end of bt878_probe.
syzbot has reported the following warning in pvr2_i2c_done:
sysfs group 'power' not found for kobject '1-0043'
When the device is disconnected (pvr_hdw_disconnect), the i2c adapter is
not unregistered along with the USB and v4l2 teardown. As part of the USB
device disconnect, the sysfs files of the subdevices are also deleted.
So, by the time pvr_i2c_core_done is called by pvr_context_destroy, the
sysfs files have been deleted.
To fix this, unregister the i2c adapter too in pvr_hdw_disconnect. Make
the device deregistration code shared by calling pvr_hdw_disconnect from
pvr2_hdw_destroy.
syzbot reported leak in cpia2 usb driver. The problem was
in invalid error handling.
v4l2_device_register() is called in cpia2_init_camera_struct(), but
all error cases after cpia2_init_camera_struct() did not call the
v4l2_device_unregister()
Reported-by: syzbot+d1e69c888f0d3866ead4@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Bixuan Cui <cuibixuan@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
pch_spi_set_tx() frees data->pkt_tx_buff on failure of kzalloc() for
data->pkt_rx_buff, but its caller, pch_spi_process_messages(), will
free data->pkt_tx_buff again. Set data->pkt_tx_buff to NULL after
kfree() to avoid double free.
A request could end up on the fpq->io list after fuse_abort_conn() has
reset fpq->connected and aborted requests on that list:
Thread-1 Thread-2
======== ========
->fuse_simple_request() ->shutdown
->__fuse_request_send()
->queue_request() ->fuse_abort_conn()
->fuse_dev_do_read() ->acquire(fpq->lock)
->wait_for(fpq->lock) ->set err to all req's in fpq->io
->release(fpq->lock)
->acquire(fpq->lock)
->add req to fpq->io
After the userspace copy is done the request will be ended, but
req->out.h.error will remain uninitialized. Also the copy might block
despite being already aborted.
Fix both issues by not allowing the request to be queued on the fpq->io
list after fuse_abort_conn() has processed this list.
Reported-by: Pradeep P V K <pragalla@codeaurora.org> Fixes: fd22d62ed0c3 ("fuse: no fc->lock for iqueue parts") Cc: <stable@vger.kernel.org> # v4.2 Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the raw memory 'data' does not go forward, it will dump repeated
data if the data length is more than 8. If we want to dump longer data
blocks, we need to repeatedly call macro SEQ_PUT_HEX_FIELD. I think it
is a bit redundant, and multiple function calls also affect the performance.
It doesn't make sense to clobber the const driver-side buffer, if a
write-to-device attempt failed. All other SSB variants (PCI, PCMCIA and SoC)
also don't corrupt the buffer on any failure in block_write.
Therefore, remove this memset from the SDIO variant.
Signed-off-by: Michael Büsch <m@bues.ch> Cc: stable@vger.kernel.org Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210515210252.318be2ba@wiggum Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I got this crash more times during debugging of PCIe controller and crash
happens somehow at the time when PCIe kernel code started link retraining (as
part of ASPM code) when at the same time PCIe link went down and ath9k probably
executed hw reset procedure.
Currently I'm not able to reproduce this issue as it looks like to be
some race condition between link training, ASPM, link down and reset
path. And as always, race conditions which depends on more input
parameters are hard to reproduce as it depends on precise timings.
But it is clear that pointers are zero in this case and should be
properly filled as same code pattern is used in ath9k_stop() function.
Anyway I was able to reproduce this crash by manually triggering ath
reset worker prior putting card up. I created simple patch to export
reset functionality via debugfs and use it to "simulate" of triggering
reset. s proved that NULL-pointer dereference issue is there.
Function ath9k_hw_reset() is dereferencing chan structure pointer, so it
needs to be non-NULL pointer.
Function ath9k_stop() already contains code which sets ah->curchan to valid
non-NULL pointer prior calling ath9k_hw_reset() function.
Add same code pattern also into ath_reset_internal() function to prevent
kernel NULL pointer dereference in ath9k_hw_reset() function.
This change fixes kernel NULL pointer dereference in ath9k_hw_reset() which
is caused by calling ath9k_hw_reset() from ath_reset_internal() with NULL
chan structure.
The ltr559 chip uses only the lowest bit of the ALS_CONTR register to
configure between active and stand-by mode. In the original driver
BIT(1) is used, which does a software reset instead.
This patch fixes the problem by using BIT(0) as als_mode_active for
the ltr559 chip.
Fixes: 8592a7eefa54 ("iio: ltr501: Add support for ltr559 chip") Signed-off-by: Oliver Lang <Oliver.Lang@gossenmetrawatt.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Nikita Travkin <nikita@trvn.ru> # ltr559 Link: https://lore.kernel.org/r/20210610134619.2101372-3-mkl@pengutronix.de Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regmap is configured for 8 bit registers, uses a RB-Tree cache and
marks several registers as volatile (i.e. do not cache).
The ALS and PS data registers in the chip are 16 bit wide and spans
two regmap registers. In the current driver only the base register is
marked as volatile, resulting in the upper register only read once.
Further the data sheet notes:
| When the I2C read operation starts, all four ALS data registers are
| locked until the I2C read operation of register 0x8B is completed.
Which results in the registers never update after the 2nd read.
This patch fixes the problem by marking the upper 8 bits of the ALS
and PS registers as volatile, too.
Fixes: 2f2c96338afc ("iio: ltr501: Add regmap support.") Reported-by: Oliver Lang <Oliver.Lang@gossenmetrawatt.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Nikita Travkin <nikita@trvn.ru> # ltr559 Link: https://lore.kernel.org/r/20210610134619.2101372-2-mkl@pengutronix.de Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently css_wait_for_slow_path() gets called inside the chp->lock.
The path-verification-loop of slowpath inside this lock could lead to
deadlock as reported by the lockdep validator.
The ccw_device_get_chp_desc() during the instance of a device-set-online
would try to acquire the same 'chp->lock' to read the chp->desc.
The instance of this function can get called from multiple scenario,
like probing or setting-device online manually. This could, in some
corner-cases lead to the deadlock.
The chp->lock was introduced to serialize the access of struct
channel_path. This lock is not needed for the css_wait_for_slow_path()
function, so invoke the slow-path function outside this lock.
When find a task from wait queue to wake up, a non-privileged task may
be found out, rather than the privileged. This maybe lead a deadlock
same as commit dfe1fe75e00e ("NFSv4: Fix deadlock between nfs4_evict_inode()
and nfs4_opendata_get_inode()"):
Privileged delegreturn task is queued to privileged list because all
the slots are assigned. If there has no enough slot to wake up the
non-privileged batch tasks(session less than 8 slot), then the privileged
delegreturn task maybe lost waked up because the found out task can't
get slot since the session is on draining.
So we should treate the privileged task as the emergency task, and
execute it as for as we can.
The 'queue->nr' will wraparound from 0 to 255 when only current
priority queue has tasks. This maybe lead a deadlock same as commit dfe1fe75e00e ("NFSv4: Fix deadlock between nfs4_evict_inode()
and nfs4_opendata_get_inode()"):
Privileged delegreturn task is queued to privileged list because all
the slots are assigned. When non-privileged task complete and release
the slot, a non-privileged maybe picked out. It maybe allocate slot
failed when the session on draining.
If the 'queue->nr' has wraparound to 255, and no enough slot to
service it, then the privileged delegreturn will lost to wake up.
After converting fs shrinkers to new scan/count API, we are no longer
pass zero nr_to_scan parameter to detect the number of objects to free,
just remove this check.
Fixes: 1ab6c4997e04 ("fs: convert fs shrinkers to new scan/count API") Cc: stable@vger.kernel.org # 3.12+ Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20210522103045.690103-2-yi.zhang@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cache_cnt parameter of tracepoint ext4_es_shrink_exit means the
remaining cache count after shrink, but now it is the cache count before
shrink, fix it by read sbi->s_extent_cache_cnt again.
Fixes: 1ab6c4997e04 ("fs: convert fs shrinkers to new scan/count API") Cc: stable@vger.kernel.org # 3.12+ Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20210522103045.690103-3-yi.zhang@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize eh_generation of struct ext4_extent_header to prevent leaking
info to userspace. Fixes KMSAN kernel-infoleak bug reported by syzbot at:
http://syzkaller.appspot.com/bug?id=78e9ad0e6952a3ca16e8234724b2fa92d041b9b8
The defrag loop processes leaves in batches and starting transaction for
each. The whole defragmentation on a given root is protected by a bit
but in case the transaction fails, the bit is not cleared
In case the transaction fails the bit would prevent starting
defragmentation again, so make sure it's cleared.
Even though we validate user-provided inputs we then traverse past
validated data when applying the new map. The issue was originally
discovered by Murray McAllister with this simple POC (if the following
is executed by an unprivileged user it will instantly panic the system):
int main(void) {
int fd, ret;
unsigned int buffer[10000];
When checking the file name attribute, we want to ensure that it fits
within the bounds of ATTR_RECORD. To do this, we should check that (attr
record + file name offset + file name length) < (attr record + attr record
length).
However, the original check did not include the file name offset in the
calculation. This means that corrupted on-disk metadata might not caught
by the incorrect file name check, and lead to an invalid memory access.
An example can be seen in the crash report of a memory corruption error
found by Syzbot:
https://syzkaller.appspot.com/bug?id=a1a1e379b225812688566745c3e2f7242bffc246
Adding the file name offset to the validity check fixes this error and
passes the Syzbot reproducer test.
The device (32a7:0000 Heimann Sensor GmbH USB appset demo) claims to be
a CDC-ACM device in its descriptors but in fact is not. If it is run
with echo disabled it returns garbled data, probably due to something
that happens in the TTY layer. And when run with echo enabled (the
default), it will mess up the calibration data of the sensor the first
time any data is sent to the device.
In short, I had a bad time after connecting the sensor and trying to get
it to work. I hope blacklisting it in the cdc-acm driver will save
someone else a bit of trouble.
when receive eem echo command, it will send a response,
but queue this response to the usb request which allocate
from gadget device endpoint zero,
and transmit the request to IN endpoint of eem interface.
on dwc3 gadget, it will trigger following warning in function
__dwc3_gadget_ep_queue(),
if (WARN(req->dep != dep, "request %pK belongs to '%s'\n",
&req->request, req->dep->name))
return -EINVAL;
fix it by allocating a usb request from IN endpoint of eem interface,
and transmit the usb request to same IN endpoint of eem interface.
In ems_usb_disconnect() dev pointer, which is netdev private data, is
used after free_candev() call:
| if (dev) {
| unregister_netdev(dev->netdev);
| free_candev(dev->netdev);
|
| unlink_all_urbs(dev);
|
| usb_free_urb(dev->intr_urb);
|
| kfree(dev->intr_in_buffer);
| kfree(dev->tx_msg_buffer);
| }
Fix it by simply moving free_candev() at the end of the block.
Fail log:
| BUG: KASAN: use-after-free in ems_usb_disconnect
| Read of size 8 at addr ffff88804e041008 by task kworker/1:2/2895
|
| CPU: 1 PID: 2895 Comm: kworker/1:2 Not tainted 5.13.0-rc5+ #164
| Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a-rebuilt.opensuse.4
| Workqueue: usb_hub_wq hub_event
| Call Trace:
| dump_stack (lib/dump_stack.c:122)
| print_address_description.constprop.0.cold (mm/kasan/report.c:234)
| kasan_report.cold (mm/kasan/report.c:420 mm/kasan/report.c:436)
| ems_usb_disconnect (drivers/net/can/usb/ems_usb.c:683 drivers/net/can/usb/ems_usb.c:1058)
Fixes: 702171adeed3 ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface") Link: https://lore.kernel.org/r/20210617185130.5834-1-paskripkin@gmail.com Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the four control requests which erroneously used usb_rcvctrlpipe().
Fixes: 1d3e20236d7a ("[PATCH] USB: usbtouchscreen: unified USB touchscreen driver") Fixes: 24ced062a296 ("usbtouchscreen: add support for DMC TSC-10/25 devices") Fixes: 9e3b25837a20 ("Input: usbtouchscreen - add support for e2i touchscreen controller") Signed-off-by: Johan Hovold <johan@kernel.org> Cc: stable@vger.kernel.org # 2.6.17 Link: https://lore.kernel.org/r/20210524092048.4443-1-johan@kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is arm port of commit 6a5022a56ac3 ("kprobes/x86: Allow to
handle reentered kprobe on single-stepping")
Since the FIQ handlers can interrupt in the single stepping
(or preparing the single stepping, do_debug etc.), we should
consider a kprobe is hit in the NMI handler. Even in that
case, the kprobe is allowed to be reentered as same as the
kprobes hit in kprobe handlers
(KPROBE_HIT_ACTIVE or KPROBE_HIT_SSDONE).
The real issue will happen when a kprobe hit while another
reentered kprobe is processing (KPROBE_REENTER), because
we already consumed a saved-area for the previous kprobe.
In order to avoid a race condition for user events when changing
cpu affinity reset the active flag only when EOI-ing the event.
This is working fine as all user events are lateeoi events. Note that
lateeoi_ack_mask_dynirq() is not modified as there is no explicit call
to xen_irq_lateeoi() expected later.
Cc: stable@vger.kernel.org Reported-by: Julien Grall <julien@xen.org> Fixes: b6622798bc50b62 ("xen/events: avoid handling the same event on two cpus at the same time") Tested-by: Julien Grall <julien@xen.org> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrvsky@oracle.com> Link: https://lore.kernel.org/r/20210623130913.9405-1-jgross@suse.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle a reported media event code of 3. This indicates that the media has
been removed from the drive and user intervention is required to proceed.
Return DISK_EVENT_EJECT_REQUEST in that case.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Control transfers without a data stage are treated as OUT requests by
the USB stack and should be using usb_sndctrlpipe(). Failing to do so
will now trigger a warning.
Fix the OSIFI2C_SET_BIT_RATE and OSIFI2C_STOP requests which erroneously
used the osif_usb_read() helper and set the IN direction bit.
Reported-by: syzbot+9d7dadd15b8819d73f41@syzkaller.appspotmail.com Fixes: 83e53a8f120f ("i2c: Add bus driver for for OSIF USB i2c device.") Cc: stable@vger.kernel.org # 3.14 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As documented in Documentation/networking/driver.rst, the ndo_start_xmit
method must not return NETDEV_TX_BUSY under any normal circumstances, and
as recommended, we simply stop the tx queue in advance, when there is a
risk that the next xmit would cause a NETDEV_TX_BUSY return.
Signed-off-by: Esben Haabendal <esben@geanix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot reported memory leak in tty_init_dev().
The problem was in unputted tty in ldisc_open()
static int ldisc_open(struct tty_struct *tty)
{
...
ser->tty = tty_kref_get(tty);
...
result = register_netdevice(dev);
if (result) {
rtnl_unlock();
free_netdev(dev);
return -ENODEV;
}
...
}
Ser pointer is netdev private_data, so after free_netdev()
this pointer goes away with unputted tty reference. So, fix
it by adding tty_kref_put() before freeing netdev.
Reported-and-tested-by: syzbot+f303e045423e617d2cad@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 31039 Comm: syz-executor.2 Not tainted 5.13.0-rc3-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function 'ping_queue_rcv_skb' not always return success, which will
also return fail. If not check the wrong return value of it, lead to function
`ping_rcv` return success.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the userland switches back-and-forth between NL80211_IFTYPE_OCB and
NL80211_IFTYPE_ADHOC via send_msg(NL80211_CMD_SET_INTERFACE), there is a
chance where the cleanup cfg80211_leave_ocb() is not called. This leads
to initialization of in-use memory (e.g. init u.ibss while in-use by
u.ocb) due to a shared struct/union within ieee80211_sub_if_data:
Revert commit 4514d991d992 ("PCI: PM: Do not read power state in
pci_enable_device_flags()") that is reported to cause PCI device
initialization issues on some systems.
Currently, -Wunused-but-set-variable is only supported by GCC so it is
disabled unconditionally in a GCC only block (it is enabled with W=1).
clang currently has its implementation for this warning in review so
preemptively move this statement out of the GCC only block and wrap it
with cc-disable-warning so that both compilers function the same.
Cc: stable@vger.kernel.org Link: https://reviews.llvm.org/D100581 Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
[nc: Backport, workaround lack of e2079e93f562 in older branches] Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building the kernel wtih gcc-10 or higher using the
CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE=y flag, the compiler picks a slightly
different set of registers for the inline assembly in cpu_init() that
subsequently results in a corrupt kernel stack as well as remaining in
FIQ mode. If a banked register is used for the last argument, the wrong
version of that register gets loaded into CPSR_c. When building in Arm
mode, the arguments are passed as immediate values and the bug cannot
happen.
This got introduced when Daniel reworked the FIQ handling and was
technically always broken, but happened to work with both clang and gcc
before gcc-10 as long as they picked one of the lower registers.
This is probably an indication that still very few people build the
kernel in Thumb2 mode.
Marek pointed out the problem on IRC, Arnd narrowed it down to this
inline assembly and Russell pinpointed the exact bug.
Change the constraints to force the final mode switch to use a non-banked
register for the argument to ensure that the correct constant gets loaded.
Another alternative would be to always use registers for the constant
arguments to avoid the #ifdef that has now become more complex.
Cc: <stable@vger.kernel.org> # v3.18+ Cc: Daniel Thompson <daniel.thompson@linaro.org> Reported-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Ard Biesheuvel <ardb@kernel.org> Fixes: c0e7f7ee717e ("ARM: 8150/3: fiq: Replace default FIQ handler") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 73f156a6e8c1 ("inetpeer: get rid of ip_id_count")
I used a very small hash table that could be abused
by patient attackers to reveal sensitive information.
Switch to a dynamic sizing, depending on RAM size.
Typical big hosts will now use 128x more storage (2 MB)
to get a similar increase in security and reduction
of hash collisions.
As a bonus, use of alloc_large_system_hash() spreads
allocated memory among all NUMA nodes.
Fixes: 73f156a6e8c1 ("inetpeer: get rid of ip_id_count") Reported-by: Amit Klein <aksecurity@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If access_ok() or fpregs_soft_set() fails in __fpu__restore_sig() then the
function just returns but does not clear the FPU state as it does for all
other fatal failures.
Clear the FPU state for these failures as well.
Fixes: 72a671ced66d ("x86, fpu: Unify signal handling code paths for x86 and x86_64 kernels") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/87mtryyhhz.ffs@nanos.tec.linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A while ago, when the "trace" file was opened, tracing was stopped, and
code was added to stop recording the comms to saved_cmdlines, for mapping
of the pids to the task name.
Code has been added that only records the comm if a trace event occurred,
and there's no reason to not trace it if the trace file is opened.
Cc: stable@vger.kernel.org Fixes: 7ffbd48d5cab2 ("tracing: Cache comms only after an event occurred") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The saved_cmdlines is used to map pids to the task name, such that the
output of the tracing does not just show pids, but also gives a human
readable name for the task.
If the name is not mapped, the output looks like this:
<...>-1316 [005] ...2 132.044039: ...
Instead of this:
gnome-shell-1316 [005] ...2 132.044039: ...
The names are updated when tracing is running, but are skipped if tracing
is stopped. Unfortunately, this stops the recording of the names if the
top level tracer is stopped, and not if there's other tracers active.
The recording of a name only happens when a new event is written into a
ring buffer, so there is no need to test if tracing is on or not. If
tracing is off, then no event is written and no need to test if tracing is
off or not.
Remove the check, as it hides the names of tasks for events in the
instance buffers.
Cc: stable@vger.kernel.org Fixes: 7ffbd48d5cab2 ("tracing: Cache comms only after an event occurred") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting hung task at register_netdevice_notifier() [1] and
unregister_netdevice_notifier() [2], for cleanup_net() might perform
time consuming operations while CAN driver's raw/bcm/isotp modules are
calling {register,unregister}_netdevice_notifier() on each socket.
Change raw/bcm/isotp modules to call register_netdevice_notifier() from
module's __init function and call unregister_netdevice_notifier() from
module's __exit function, as with gw/j1939 modules are doing.
Some NVIDIA GPU devices do not work with SBR. Triggering SBR leaves the
device inoperable for the current system boot. It requires a system
hard-reboot to get the GPU device back to normal operating condition
post-SBR. For the affected devices, enable NO_BUS_RESET quirk to avoid the
issue.
This issue will be fixed in the next generation of hardware.
Link: https://lore.kernel.org/r/20210608054857.18963-8-ameynarkhede03@gmail.com Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Sinan Kaya <okaya@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some TI KeyStone C667X devices do not support bus/hot reset. The PCIESS
automatically disables LTSSM when Secondary Bus Reset is received and
device stops working. Prevent bus reset for these devices. With this
change, the device can be assigned to VMs with VFIO, but it will leak state
between VMs.
Reference: https://e2e.ti.com/support/processors/f/791/t/954382 Link: https://lore.kernel.org/r/20210315102606.17153-1-antti.jarvinen@gmail.com Signed-off-by: Antti Järvinen <antti.jarvinen@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The trace_clock_global() tries to make sure the events between CPUs is
somewhat in order. A global value is used and updated by the latest read
of a clock. If one CPU is ahead by a little, and is read by another CPU, a
lock is taken, and if the timestamp of the other CPU is behind, it will
simply use the other CPUs timestamp.
The lock is also only taken with a "trylock" due to tracing, and strange
recursions can happen. The lock is not taken at all in NMI context.
In the case where the lock is not able to be taken, the non synced
timestamp is returned. But it will not be less than the saved global
timestamp.
The problem arises because when the time goes "backwards" the time
returned is the saved timestamp plus 1. If the lock is not taken, and the
plus one to the timestamp is returned, there's a small race that can cause
the time to go backwards!
The above case shows to reads of trace_clock_global() on the same CPU, but
the second read returns one less than the first read. That is, time when
backwards, and this is not what is allowed by trace_clock_global().
This was triggered by heavy tracing and the ring buffer checker that tests
for the clock going backwards:
On 64-bit systems, struct bcm_msg_head has an added padding of 4 bytes between
struct members count and ival1. Even though all struct members are initialized,
the 4-byte hole will contain data from the kernel stack. This patch zeroes out
struct bcm_msg_head before usage, preventing infoleaks to userspace.
I met a gpu addr bug recently and the kernel log
tells me the pc is memcpy/memset and link register is
radeon_uvd_resume.
As we know, in some architectures, optimized memcpy/memset
may not work well on device memory. Trival memcpy_toio/memset_io
can fix this problem.
BTW, amdgpu has already done it in:
commit ba0b2275a678 ("drm/amdgpu: use memcpy_to/fromio for UVD fw upload"),
that's why it has no this issue on the same gpu and platform.
Signed-off-by: Chen Li <chenli@uniontech.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
scsi_host_dev_release() only frees dev_name when host state is
SHOST_CREATED. After host state has changed to SHOST_RUNNING,
scsi_host_dev_release() no longer cleans up.
Fix this by doing a put_device(&shost->shost_dev) in the failure path when
host state is SHOST_RUNNING. Move get_device(&shost->shost_gendev) before
device_add(&shost->shost_dev) so that scsi_host_cls_release() can do a put
on this reference.
Link: https://lore.kernel.org/r/20210602133029.2864069-4-ming.lei@redhat.com Cc: Bart Van Assche <bvanassche@acm.org> Cc: Hannes Reinecke <hare@suse.de> Reported-by: John Garry <john.garry@huawei.com> Tested-by: John Garry <john.garry@huawei.com> Reviewed-by: John Garry <john.garry@huawei.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
priv is netdev private data, but it is used
after free_netdev(). It can cause use-after-free when accessing priv
pointer. So, fix it by moving free_netdev() after pci_iounmap()
calls.
Fixes: 6af55ff52b02 ("Driver for Beckhoff CX5020 EtherCAT master module.") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
when usbnet transmit a skb, eem fixup it in eem_tx_fixup(),
if skb_copy_expand() failed, it return NULL,
usbnet_start_xmit() will have no chance to free original skb.
fix it by free orginal skb in eem_tx_fixup() first,
then check skb clone status, if failed, return NULL to usbnet.
Fixes: 9f722c0978b0 ("usbnet: CDC EEM support (v5)") Signed-off-by: Linyu Yuan <linyyuan@codeaurora.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 815f62bf7427 ("[PATCH] SMP rewrite of mkiss") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: d6b6d9877878 ("be2net: use PCIe AER capability") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While unix_may_send(sk, osk) is called while osk is locked, it appears
unix_release_sock() can overwrite unix_peer() after this lock has been
released, making KCSAN unhappy.
Changing unix_release_sock() to access/change unix_peer()
before lock is released should fix this issue.
BUG: KCSAN: data-race in unix_dgram_sendmsg / unix_release_sock
write to 0xffff88810465a338 of 8 bytes by task 20852 on cpu 1:
unix_release_sock+0x4ed/0x6e0 net/unix/af_unix.c:558
unix_release+0x2f/0x50 net/unix/af_unix.c:859
__sock_release net/socket.c:599 [inline]
sock_close+0x6c/0x150 net/socket.c:1258
__fput+0x25b/0x4e0 fs/file_table.c:280
____fput+0x11/0x20 fs/file_table.c:313
task_work_run+0xae/0x130 kernel/task_work.c:164
tracehook_notify_resume include/linux/tracehook.h:189 [inline]
exit_to_user_mode_loop kernel/entry/common.c:175 [inline]
exit_to_user_mode_prepare+0x156/0x190 kernel/entry/common.c:209
__syscall_exit_to_user_mode_work kernel/entry/common.c:291 [inline]
syscall_exit_to_user_mode+0x20/0x40 kernel/entry/common.c:302
do_syscall_64+0x56/0x90 arch/x86/entry/common.c:57
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88810465a338 of 8 bytes by task 20888 on cpu 0:
unix_may_send net/unix/af_unix.c:189 [inline]
unix_dgram_sendmsg+0x923/0x1610 net/unix/af_unix.c:1712
sock_sendmsg_nosec net/socket.c:654 [inline]
sock_sendmsg net/socket.c:674 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2350
___sys_sendmsg net/socket.c:2404 [inline]
__sys_sendmmsg+0x315/0x4b0 net/socket.c:2490
__do_sys_sendmmsg net/socket.c:2519 [inline]
__se_sys_sendmmsg net/socket.c:2516 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2516
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0xffff888167905400 -> 0x0000000000000000
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 20888 Comm: syz-executor.0 Not tainted 5.13.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 46a8b29c6306 ("net: usb: fix memory leak in smsc75xx_bind")
fails to clean up the work scheduled in smsc75xx_reset->
smsc75xx_set_multicast, which leads to use-after-free if the work is
scheduled to start after the deallocation. In addition, this patch
also removes a dangling pointer - dev->data[0].
This patch calls cancel_work_sync to cancel the scheduled work and set
the dangling pointer to NULL.
Fixes: 46a8b29c6306 ("net: usb: fix memory leak in smsc75xx_bind") Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is meant to make the host side cdc_ncm interface consistently
named just like the older CDC protocols: cdc_ether & cdc_ecm
(and even rndis_host), which all use 'FLAG_ETHER | FLAG_POINTTOPOINT'.
include/linux/usb/usbnet.h:
#define FLAG_ETHER 0x0020 /* maybe use "eth%d" names */
#define FLAG_WLAN 0x0080 /* use "wlan%d" names */
#define FLAG_WWAN 0x0400 /* use "wwan%d" names */
#define FLAG_POINTTOPOINT 0x1000 /* possibly use "usb%d" names */
drivers/net/usb/usbnet.c @ line 1711:
strcpy (net->name, "usb%d");
...
// heuristic: "usb%d" for links we know are two-host,
// else "eth%d" when there's reasonable doubt. userspace
// can rename the link if it knows better.
if ((dev->driver_info->flags & FLAG_ETHER) != 0 &&
((dev->driver_info->flags & FLAG_POINTTOPOINT) == 0 ||
(net->dev_addr [0] & 0x02) == 0))
strcpy (net->name, "eth%d");
/* WLAN devices should always be named "wlan%d" */
if ((dev->driver_info->flags & FLAG_WLAN) != 0)
strcpy(net->name, "wlan%d");
/* WWAN devices should always be named "wwan%d" */
if ((dev->driver_info->flags & FLAG_WWAN) != 0)
strcpy(net->name, "wwan%d");
So by using ETHER | POINTTOPOINT the interface naming is
either usb%d or eth%d based on the global uniqueness of the
mac address of the device.
Without this 2.5gbps ethernet dongles which all seem to use the cdc_ncm
driver end up being called usb%d instead of eth%d even though they're
definitely not two-host. (All 1gbps & 5gbps ethernet usb dongles I've
tested don't hit this problem due to use of different drivers, primarily
r8152 and aqc111)
Fixes tag is based purely on git blame, and is really just here to make
sure this hits LTS branches newer than v4.5.
Cc: Lorenzo Colitti <lorenzo@google.com> Fixes: 4d06dd537f95 ("cdc_ncm: do not call usbnet_link_change from cdc_ncm_bind") Signed-off-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: e87ad5539343 ("netxen: support pci error handlers") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
