phy: rockchip-pcie: Properly disable TEST_WRITE strobe signal
pcie_conf is used to touch TEST_WRITE strobe signal. This signal should
be enabled, a little time waited, and then disabled. Current code clearly
was copy-pasted and never disables the strobe signal. Adjust the define.
While at it, remove PHY_CFG_RD_MASK which has been unused since 64cdc0360811 ("phy: rockchip-pcie: remove unused phy_rd_cfg function").
phy: rockchip-pcie: Enable all four lanes if required
Current code enables only Lane 0 because pwr_cnt will be incremented on
first call to the function. Let's reorder the enablement code to enable
all 4 lanes through GRF.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Valmantas Paliksa <walmis@gmail.com> Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/16b610aab34e069fd31d9f57260c10df2a968f80.1751322015.git.geraldogabriel@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: Update pcie phy bindings for QCS615
QCS615 pcie phy only use 5 clocks, which are aux, cfg_ahb, ref,
ref_gen, pipe. So move "qcom,qcs615-qmp-gen3x1-pcie-phy" compatible
from 6 clocks' list to 5 clocks' list.
phy: qcom: qmp-combo: Add missing PLL (VCO) configuration on SM8750
Add missing DP PHY status and VCO clock configuration registers to fix
configuring the VCO rate on SM8750. Without proper VCO rate setting, it
works on after-reset half of rate which is not enough for DP over USB to
work as seen on logs:
[drm:msm_dp_ctrl_link_train_1_2] *ERROR* max v_level reached
[drm:msm_dp_ctrl_link_train_1_2] *ERROR* link training #1 on phy 0 failed. ret=-11
Fixes: c4364048baf4 ("phy: qcom: qmp-combo: Add new PHY sequences for SM8750") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250616062541.7167-2-krzysztof.kozlowski@linaro.org Signed-off-by: Vinod Koul <vkoul@kernel.org>
Zeroing out registers does not happen in the downstream kernel, and will
"tune" the repeater in surely unexpected ways since most registers don't
have a reset value of 0x0.
Stop doing that and instead just set the registers that are in the init
sequence (though long term I don't think there's actually PMIC-specific
init sequences, there's board specific tuning, but that's a story for
another day).
Fixes: 99a517a582fc ("phy: qualcomm: phy-qcom-eusb2-repeater: Zero out untouched tuning regs") Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20250617-eusb2-repeater-tuning-v2-2-ed6c484f18ee@fairphone.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
phy: mediatek: tphy: Cleanup and document slew calibration
While it's true that, generally, the T-PHY V3 does not support the
slew calibration process, some minor versions of it actually do,
moreover, some SoCs may not support this even though the version
of the PHY IP does.
The reference clock and rate coefficient parameters are used only
for slew calibration: move those to platform data, then document
and change the checks in hs_slew_rate_calibrate() to perform the
calibration only if:
- EYE value was not supplied (pre-calculated calibration); and
- Slew reference clock value is present (not zero); and
- Slew coefficient is present (not zero).
Moreover, change the probe function to always check if both the
slew reference clock and coefficient properties are present and,
if not, assign the value from platform data (which, as reminder,
if not added means that it's zero!), instead of checking the PHY
IP version.
phy: mediatek: tphy: Clarify and add kerneldoc to mtk_phy_pdata
As struct mtk_phy_pdata was almost fully documented, transfer
the comments into kerneldoc on top.
While at it, also rewrite the comments to both improve the writing
writing and the actual information in the documentation, and add a
description for the `version` member of the structure.
Nitin Rawat [Mon, 23 Jun 2025 13:48:09 +0000 (19:18 +0530)]
scsi: ufs: qcom : Fix NULL pointer dereference in ufs_qcom_setup_clocks
Fix a NULL pointer dereference in ufs_qcom_setup_clocks due to an
uninitialized 'host' variable. The variable 'phy' is now assigned
after confirming 'host' is not NULL.
Call Stack:
Unable to handle kernel NULL pointer dereference at
virtual address 0000000000000000
Randy Dunlap [Tue, 17 Jun 2025 03:42:49 +0000 (20:42 -0700)]
phy: qcom: add linux/bitfield.h header to fix a build error
Add the <linux/bitfield.h> header to prevent a build error:
drivers/phy/qualcomm/phy-qcom-m31-eusb2.c: In function 'm31eusb2_phy_init':
drivers/phy/qualcomm/phy-qcom-m31-eusb2.c:210:37: error: implicit declaration of function 'FIELD_PREP' [-Wimplicit-function-declaration]
210 | FIELD_PREP(FSEL, data->fsel));
The devm_of_phy_optional_get() takes an optional name argument as its
third parameter and not an index like the recently replaced
devm_of_phy_get_by_index().
Replace 0 with an explicit NULL for consistency and readability.
Johan Hovold [Fri, 23 May 2025 08:48:34 +0000 (10:48 +0200)]
phy: phy-snps-eusb2: fix repeater imbalance on phy_init() failure
Make sure to disable the repeater PHY also on phy_init() failure.
Fixes: 3584f6392f09 ("phy: qcom: phy-qcom-snps-eusb2: Add support for eUSB2 repeater") Cc: Abel Vesa <abel.vesa@linaro.org> Cc: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20250523084839.11015-3-johan+linaro@kernel.org Signed-off-by: Vinod Koul <vkoul@kernel.org>
Wesley Cheng [Tue, 27 May 2025 21:04:42 +0000 (14:04 -0700)]
phy: qcom: Add M31 based eUSB2 PHY driver
SM8750 utilizes an eUSB2 PHY from M31. Add the initialization
sequences to bring it out of reset and into an operational state. This
differs to the M31 USB driver, in that the M31 eUSB2 driver will
require a connection to an eUSB2 repeater. This PHY driver will handle
the initialization of the associated eUSB2 repeater when required.
Wesley Cheng [Tue, 27 May 2025 21:04:41 +0000 (14:04 -0700)]
phy: qcom: Update description for QCOM based eUSB2 repeater
The eUSB2 repeater that exists in the QCOM PMICs are utilized for several
different eUSB2 PHY vendors, such as M31 or Synopsys. Hence, the wording
needs to be updated to remove associations to a specific vendor.
Wesley Cheng [Tue, 27 May 2025 21:04:40 +0000 (14:04 -0700)]
phy: qcom: qmp-combo: Add new PHY sequences for SM8750
Add new register offsets and PHY values for SM8750. Some of the previous
definitions can be leveraged from older PHY versions as offsets within
registers have not changed. This also adds the required PHY sequence that
is recommended after running hardware characterization.
Lad Prabhakar [Wed, 28 May 2025 13:38:58 +0000 (14:38 +0100)]
dt-bindings: phy: renesas,usb2-phy: Document RZ/V2N SoC support
Document support for the USB2.0 phy found on the Renesas RZ/V2N
(R9A09G056) SoC. The USB2.0 phy is functionally identical to that on the
RZ/V2H(P) SoC, so no driver changes are needed. The existing
`renesas,usb2-phy-r9a09g057` compatible will be used as a fallback
for the RZ/V2N SoC.
dt-bindings: phy: Convert ti,keystone-usbphy to DT schema
Convert the TI Keystone USB PHY binding to DT schema format. Drop the
"#address-cells" and "#size-cells" properties which don't make sense
without any child nodes.
Nitin Rawat [Mon, 26 May 2025 15:38:21 +0000 (21:08 +0530)]
scsi: ufs: qcom : Refactor phy_power_on/off calls
Commit 3f6d1767b1a0 ("phy: ufs-qcom: Refactor all init steps into
phy_poweron") moved the phy_power_on/off from ufs_qcom_setup_clocks
to suspend/resume func.
To have a better power saving, remove the phy_power_on/off calls from
resume/suspend path and put them back to ufs_qcom_setup_clocks, so that
PHY regulators & clks can be turned on/off along with UFS's clocks.
Since phy phy_power_on is separated out from phy calibrate, make
separate calls to phy_power_on calls from ufs qcom driver.
Nitin Rawat [Mon, 26 May 2025 15:38:20 +0000 (21:08 +0530)]
phy: qcom-qmp-ufs: refactor qmp_ufs_power_off
In qmp_ufs_power_off, the PHY is already powered down by asserting
QPHY_PCS_POWER_DOWN_CONTROL. Therefore, additional phy_reset and
stopping SerDes are unnecessary. Also this approach does not
align with the phy HW programming guide.
Thus, refactor qmp_ufs_power_off to remove the phy_reset and stop
SerDes calls to simplify the code and ensure alignment with the PHY
HW programming guide.
Nitin Rawat [Mon, 26 May 2025 15:38:19 +0000 (21:08 +0530)]
phy: qcom-qmp-ufs: Remove qmp_ufs_exit() and Inline qmp_ufs_com_exit()
qmp_ufs_exit() is a wrapper function. It only calls qmp_ufs_com_exit().
Remove it to simplify the ufs phy driver.
Additonally partial Inline(dropping the reset assert) qmp_ufs_com_exit
into qmp_ufs_power_off function to avoid unnecessary function call
and to align with the Phy programming guide.
Nitin Rawat [Mon, 26 May 2025 15:38:18 +0000 (21:08 +0530)]
phy: qcom-qmp-ufs: Rename qmp_ufs_power_off
Rename qmp_ufs_disable to qmp_ufs_power_off to better represent its
functionality. Additionally, inline qmp_ufs_exit into qmp_ufs_power_off
function to preserve the functionality of .power_off.
Nitin Rawat [Mon, 26 May 2025 15:38:17 +0000 (21:08 +0530)]
phy: qcom-qmp-ufs: Remove qmp_ufs_com_init()
The qmp_ufs_power_on() function acts as a wrapper, solely invoking
qmp_ufs_com_init(). Additionally, the code within qmp_ufs_com_init()
does not correspond well with its name.
Therefore, to enhance the readability and eliminate unnecessary
function call inline qmp_ufs_com_init() into qmp_ufs_power_on().
Nitin Rawat [Mon, 26 May 2025 15:38:16 +0000 (21:08 +0530)]
phy: qcom-qmp-ufs: Refactor UFS PHY reset
Refactor the UFS PHY reset handling to parse the reset logic only once
during initialization, instead of every resume.
As part of this change, move the UFS PHY reset parsing logic from
qmp_phy_power_on to the new qmp_ufs_phy_init function introduced
as part of phy_ops::init callback.
Nitin Rawat [Mon, 26 May 2025 15:38:15 +0000 (21:08 +0530)]
phy: qcom-qmp-ufs: Refactor phy_power_on and phy_calibrate callbacks
Commit 052553af6a31 ("ufs/phy: qcom: Refactor to use phy_init call")
puts enabling regulators & clks, calibrating UFS PHY, starting serdes
and polling PCS ready status into phy_power_on.
In Current code regulators enable, clks enable, calibrating UFS PHY,
start_serdes and polling PCS_ready_status are part of phy_power_on.
UFS PHY registers are retained after power collapse, meaning calibrating
UFS PHY, start_serdes and polling PCS_ready_status can be done only when
hba is powered_on, and not needed every time when phy_power_on is called
during resume. Hence keep the code which enables PHY's regulators & clks
in phy_power_on and move the rest steps into phy_calibrate function.
Refactor the code to retain PHY regulators & clks in phy_power_on and
move out rest of the code to new phy_calibrate function.
Also move reset_control_assert to qmp_ufs_phy_calibrate to align
with Hardware programming guide.
Nitin Rawat [Mon, 26 May 2025 15:38:14 +0000 (21:08 +0530)]
phy: qcom-qmp-ufs: Rename qmp_ufs_enable and qmp_ufs_power_on
Rename qmp_ufs_enable to qmp_ufs_power_on and qmp_ufs_power_on to
qmp_ufs_phy_calibrate to better reflect their functionality. Also
update function calls and structure assignments accordingly.
Nitin Rawat [Mon, 26 May 2025 15:38:13 +0000 (21:08 +0530)]
scsi: ufs: qcom: add a new phy calibrate API call
Introduce a new phy calibrate API call in the UFS Qualcomm driver to
separate phy calibration from phy power-on. This change is a precursor
to the successive commits in this series, which requires these two
operations to be distinct.
The Exynos7870 MIPI PHY device contains one DSIM PHY block and three
CSIS PHY blocks. It also requires two sysregs, one for display, and the
other for cameras. Document this device.
Linus Torvalds [Sun, 8 Jun 2025 18:33:00 +0000 (11:33 -0700)]
Merge tag 'timers-cleanups-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer cleanup from Thomas Gleixner:
"The delayed from_timer() API cleanup:
The renaming to the timer_*() namespace was delayed due massive
conflicts against Linux-next. Now that everything is upstream finish
the conversion"
* tag 'timers-cleanups-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
treewide, timers: Rename from_timer() to timer_container_of()
Linus Torvalds [Sun, 8 Jun 2025 18:27:20 +0000 (11:27 -0700)]
Merge tag 'x86-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A small set of x86 fixes:
- Cure IO bitmap inconsistencies
A failed fork cleans up all resources of the newly created thread
via exit_thread(). exit_thread() invokes io_bitmap_exit() which
does the IO bitmap cleanups, which unfortunately assume that the
cleanup is related to the current task, which is obviously bogus.
Make it work correctly
- A lockdep fix in the resctrl code removed the clearing of the
command buffer in two places, which keeps stale error messages
around. Bring them back.
- Remove unused trace events"
* tag 'x86-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fs/resctrl: Restore the rdt_last_cmd_clear() calls after acquiring rdtgroup_mutex
x86/iopl: Cure TIF_IO_BITMAP inconsistencies
x86/fpu: Remove unused trace events
Zhang Rui [Fri, 30 May 2025 00:09:28 +0000 (08:09 +0800)]
tools/power turbostat: Avoid probing the same perf counters
For the RAPL package energy status counter, Intel and AMD share the same
perf_subsys and perf_name, but with different MSR addresses.
Both rapl_counter_arch_infos[0] and rapl_counter_arch_infos[1] are
introduced to describe this counter for different Vendors.
As a result, the perf counter is probed twice, and causes a failure in
in get_rapl_counters() because expected_read_size and actual_read_size
don't match.
Fix the problem by skipping the already probed counter.
Note, this is not a perfect fix. For example, if different
vendors/platforms use the same MSR value for different purpose, the code
can be fooled when it probes a rapl_counter_arch_infos[] entry that does
not belong to the running Vendor/Platform.
In a long run, better to put rapl_counter_arch_infos[] into the
platform_features so that this becomes Vendor/Platform specific.
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Sat, 17 May 2025 09:44:50 +0000 (17:44 +0800)]
tools/power turbostat: Allow probing RAPL with platform_features->rapl_msrs cleared
platform_features->rapl_msrs describes the RAPL MSRs supported. While
RAPL Perf counters can be exposed from different kernel backend drivers,
e.g. RAPL MSR I/F driver, or RAPL TPMI I/F driver.
Thus, turbostat should first blindly probe all the available RAPL Perf
counters, and falls back to the RAPL MSR counters if they are listed in
platform_features->rapl_msrs.
With this, platforms that don't have RAPL MSRs can clear the
platform_features->rapl_msrs bits and use RAPL Perf counters only.
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
probe_rapl_msr() is reused for probing RAPL MSR counters, cstate MSR
counters and MPERF/APERF/SMI MSR counters, thus its name is misleading.
Similar to add_perf_counter(), introduce add_msr_counter() to probe a
counter via MSR. Introduce wrapper function add_rapl_msr_counter() at
the same time to add extra check for Zero return value for specified
RAPL counters.
No functional change intended.
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
As the only caller of add_cstate_perf_counter_(),
add_cstate_perf_counter() just gives extra debug output on top. There is
no need to keep both functions.
Remove add_cstate_perf_counter_() and move all the logic to
add_cstate_perf_counter().
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
commit 05a2f07db888 ("tools/power turbostat: read RAPL counters via
perf") that adds support to read RAPL counters via perf defines the
notion of a RAPL domain_id which is set to physical_core_id on
platforms which support per_core_rapl counters (Eg: AMD processors
Family 17h onwards) and is set to the physical_package_id on all the
other platforms.
However, the physical_core_id is only unique within a package and on
platforms with multiple packages more than one core can have the same
physical_core_id and thus the same domain_id. (For eg, the first cores
of each package have the physical_core_id = 0). This results in all
these cores with the same physical_core_id using the same entry in the
rapl_counter_info_perdomain[]. Since rapl_perf_init() skips the
perf-initialization for cores whose domain_ids have already been
visited, cores that have the same physical_core_id always read the
perf file corresponding to the physical_core_id of the first package
and thus the package-energy is incorrectly reported to be the same
value for different packages.
Note: This issue only arises when RAPL counters are read via perf and
not when they are read via MSRs since in the latter case the MSRs are
read separately on each core.
Fix this issue by associating each CPU with rapl_core_id which is
unique across all the packages in the system.
Fixes: 05a2f07db888 ("tools/power turbostat: read RAPL counters via perf") Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com> Signed-off-by: Len Brown <len.brown@intel.com>
tools/power turbostat: Add Android support for MSR device handling
It uses /dev/msrN device paths on Android instead of /dev/cpu/N/msr,
updates error messages and permission checks to reflect the Android
device path, and wraps platform-specific code with #if defined(ANDROID)
to ensure correct behavior on both Android and non-Android systems.
These changes improve compatibility and usability of turbostat on
Android devices.
Signed-off-by: Kaushlendra Kumar <kaushlendra.kumar@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Sun, 8 Jun 2025 18:07:33 +0000 (11:07 -0700)]
Merge tag 'perf-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 perf fix from Thomas Gleixner:
"A single fix for the x86 performance counters on Intel CPUs:
The MSR offset calculations for fixed performance counters are stored
at the wrong index in the configuration array causing the general
purpose counter MSR offset to be overwritten, so both the general
purpose and the fixed counters offsets are incorrect.
Correct the array index calculation to fix that"
* tag 'perf-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Fix incorrect MSR index calculations in intel_pmu_config_acr()
Linus Torvalds [Sun, 8 Jun 2025 18:02:53 +0000 (11:02 -0700)]
Merge tag 'irq-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single fix for the PCI/MSI code:
The conversion to per device MSI domains created a MSI domain with
size 1 instead of sizing it to the maximum possible number of MSI
interrupts for the device. This "worked" as the subsequent allocations
resized the domain, but the recent change to move the prepare() call
into the domain creation path broke this works by chance mechanism.
Size the domain properly at creation time"
* tag 'irq-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
PCI/MSI: Size device MSI domain with the maximum number of vectors
Linus Torvalds [Sun, 8 Jun 2025 17:35:12 +0000 (10:35 -0700)]
Merge tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull mount fixes from Al Viro:
"Various mount-related bugfixes:
- split the do_move_mount() checks in subtree-of-our-ns and
entire-anon cases and adapt detached mount propagation selftest for
mount_setattr
- allow clone_private_mount() for a path on real rootfs
- fix a race in call of has_locked_children()
- fix move_mount propagation graph breakage by MOVE_MOUNT_SET_GROUP
- make sure clone_private_mnt() caller has CAP_SYS_ADMIN in the right
userns
- avoid false negatives in path_overmount()
- don't leak MNT_LOCKED from parent to child in finish_automount()
- do_change_type(): refuse to operate on unmounted/not ours mounts"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
do_change_type(): refuse to operate on unmounted/not ours mounts
clone_private_mnt(): make sure that caller has CAP_SYS_ADMIN in the right userns
selftests/mount_setattr: adapt detached mount propagation test
do_move_mount(): split the checks in subtree-of-our-ns and entire-anon cases
fs: allow clone_private_mount() for a path on real rootfs
fix propagation graph breakage by MOVE_MOUNT_SET_GROUP move_mount(2)
finish_automount(): don't leak MNT_LOCKED from parent to child
path_overmount(): avoid false negatives
fs/fhandle.c: fix a race in call of has_locked_children()
Linus Torvalds [Sun, 8 Jun 2025 17:20:21 +0000 (10:20 -0700)]
Merge tag '6.16-rc-part2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- multichannel/reconnect fixes
- move smbdirect (smb over RDMA) defines to fs/smb/common so they will
be able to be used in the future more broadly, and a documentation
update explaining setting up smbdirect mounts
- update email address for Paulo
* tag '6.16-rc-part2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal version number
MAINTAINERS, mailmap: Update Paulo Alcantara's email address
cifs: add documentation for smbdirect setup
cifs: do not disable interface polling on failure
cifs: serialize other channels when query server interfaces is pending
cifs: deal with the channel loading lag while picking channels
smb: client: make use of common smbdirect_socket_parameters
smb: smbdirect: introduce smbdirect_socket_parameters
smb: client: make use of common smbdirect_socket
smb: smbdirect: add smbdirect_socket.h
smb: client: make use of common smbdirect.h
smb: smbdirect: add smbdirect.h with public structures
smb: client: make use of common smbdirect_pdu.h
smb: smbdirect: add smbdirect_pdu.h with protocol definitions
Linus Torvalds [Sun, 8 Jun 2025 15:19:01 +0000 (08:19 -0700)]
Merge tag 'trace-v6.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull more tracing fixes from Steven Rostedt:
- Fix regression of waiting a long time on updating trace event filters
When the faultable trace points were added, it needed task trace RCU
synchronization.
This was added to the tracepoint_synchronize_unregister() function.
The filter logic always called this function whenever it updated the
trace event filters before freeing the old filters. This increased
the time of "trace-cmd record" from taking 13 seconds to running over
2 minutes to complete.
Move the freeing of the filters to call_rcu*() logic, which brings
the time back down to 13 seconds.
The error path of the ring_buffer_subbuf_order_set() released the
mutex too early and allowed subsequent accesses to setting the
subbuffer size to corrupt the data and cause a bug.
By moving the mutex locking to the end of the error path, it prevents
the reentrant access to the critical data and also allows the
function to convert the taking of the mutex over to the guard()
logic.
- Remove unused power management clock events
The clock events were added in 2010 for power management. In 2011 arm
used them. In 2013 the code they were used in was removed. These
events have been wasting memory since then.
- Fix sparse warnings
There was a few places that sparse warned about trace_events_filter.c
where file->filter was referenced directly, but it is annotated with
an __rcu tag. Use the helper functions and fix them up to use
rcu_dereference() properly.
* tag 'trace-v6.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Add rcu annotation around file->filter accesses
tracing: PM: Remove unused clock events
ring-buffer: Fix buffer locking in ring_buffer_subbuf_order_set()
tracing: Fix regression of filter waiting a long time on RCU synchronization
Linus Torvalds [Sat, 7 Jun 2025 17:05:35 +0000 (10:05 -0700)]
Merge tag 'kbuild-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Add support for the EXPORT_SYMBOL_GPL_FOR_MODULES() macro, which
exports a symbol only to specified modules
- Improve ABI handling in gendwarfksyms
- Forcibly link lib-y objects to vmlinux even if CONFIG_MODULES=n
- Add checkers for redundant or missing <linux/export.h> inclusion
- Deprecate the extra-y syntax
- Fix a genksyms bug when including enum constants from *.symref files
* tag 'kbuild-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (28 commits)
genksyms: Fix enum consts from a reference affecting new values
arch: use always-$(KBUILD_BUILTIN) for vmlinux.lds
kbuild: set y instead of 1 to KBUILD_{BUILTIN,MODULES}
efi/libstub: use 'targets' instead of extra-y in Makefile
module: make __mod_device_table__* symbols static
scripts/misc-check: check unnecessary #include <linux/export.h> when W=1
scripts/misc-check: check missing #include <linux/export.h> when W=1
scripts/misc-check: add double-quotes to satisfy shellcheck
kbuild: move W=1 check for scripts/misc-check to top-level Makefile
scripts/tags.sh: allow to use alternative ctags implementation
kconfig: introduce menu type enum
docs: symbol-namespaces: fix reST warning with literal block
kbuild: link lib-y objects to vmlinux forcibly even when CONFIG_MODULES=n
tinyconfig: enable CONFIG_LD_DEAD_CODE_DATA_ELIMINATION
docs/core-api/symbol-namespaces: drop table of contents and section numbering
modpost: check forbidden MODULE_IMPORT_NS("module:") at compile time
kbuild: move kbuild syntax processing to scripts/Makefile.build
Makefile: remove dependency on archscripts for header installation
Documentation/kbuild: Add new gendwarfksyms kABI rules
Documentation/kbuild: Drop section numbers
...
Linus Torvalds [Sat, 7 Jun 2025 17:00:03 +0000 (10:00 -0700)]
Merge tag 'sh-for-v6.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
- replace the __ASSEMBLY__ with __ASSEMBLER__ macro in all headers
since the latter is now defined automatically by both GCC and Clang
when compiling assembly code (Thomas Huth)
- set the default SPI mode for the ecovec24 board which became
necessary after a new mode member as added to the sh_msiof_spi_info
struct in cf9e4784f3bd ("spi: sh-msiof: Add slave mode support")
(Geert Uytterhoeven)
- remove unused variables in the kprobes code in
kprobe_exceptions_notify() (Mike Rapoport)
* tag 'sh-for-v6.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: kprobes: Remove unused variables in kprobe_exceptions_notify()
sh: ecovec24: Make SPI mode explicit
sh: Replace __ASSEMBLY__ with __ASSEMBLER__ in all headers
Linus Torvalds [Sat, 7 Jun 2025 16:56:18 +0000 (09:56 -0700)]
Merge tag 'loongarch-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch updates from Huacai Chen:
- Adjust the 'make install' operation
- Support SCHED_MC (Multi-core scheduler)
- Enable ARCH_SUPPORTS_MSEAL_SYSTEM_MAPPINGS
- Enable HAVE_ARCH_STACKLEAK
- Increase max supported CPUs up to 2048
- Introduce the numa_memblks conversion
- Add PWM controller nodes in dts
- Some bug fixes and other small changes
* tag 'loongarch-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
platform/loongarch: laptop: Unregister generic_sub_drivers on exit
platform/loongarch: laptop: Add backlight power control support
platform/loongarch: laptop: Get brightness setting from EC on probe
LoongArch: dts: Add PWM support to Loongson-2K2000
LoongArch: dts: Add PWM support to Loongson-2K1000
LoongArch: dts: Add PWM support to Loongson-2K0500
LoongArch: vDSO: Correctly use asm parameters in syscall wrappers
LoongArch: Fix panic caused by NULL-PMD in huge_pte_offset()
LoongArch: Preserve firmware configuration when desired
LoongArch: Avoid using $r0/$r1 as "mask" for csrxchg
LoongArch: Introduce the numa_memblks conversion
LoongArch: Increase max supported CPUs up to 2048
LoongArch: Enable HAVE_ARCH_STACKLEAK
LoongArch: Enable ARCH_SUPPORTS_MSEAL_SYSTEM_MAPPINGS
LoongArch: Add SCHED_MC (Multi-core scheduler) support
LoongArch: Add some annotations in archhelp
LoongArch: Using generic scripts/install.sh in `make install`
LoongArch: Add a default install.sh
Linus Torvalds [Sat, 7 Jun 2025 16:40:08 +0000 (09:40 -0700)]
Merge tag 'sound-fix-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of fix patches for the 6.16-rc1 merge window.
Most of changes are about ASoC, especially lots of AVS driver fixes.
Larger LOCs are seen in TAS571x codec drivers, but the changes are
trivial and safe. The rest are all device-specific small fixes"
* tag 'sound-fix-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (27 commits)
ASoC: Intel: avs: boards: Fix rt5663 front end name
ASoC: Intel: avs: Simplify verification of parse_int_array() result
ALSA: usb-audio: Add implicit feedback quirk for RODE AI-1
ALSA: hda: Ignore unsol events for cards being shut down
ALSA: hda: Add new pci id for AMD GPU display HD audio controller
ALSA: hda: cs35l41: Constify regmap_irq_chip
ALSA: usb-audio: Add a quirk for Lenovo Thinkpad Thunderbolt 3 dock
ASoC: ti: omap-hdmi: Re-add dai_link->platform to fix card init
ASoC: pcm: Do not open FEs with no BEs connected
ASoC: rt1320: fix speaker noise when volume bar is 100%
ASoC: Intel: avs: Include missing string.h
ASoC: Intel: avs: Verify content returned by parse_int_array()
ASoC: Intel: avs: Verify kcalloc() status when setting constraints
ASoC: Intel: avs: Fix paths in MODULE_FIRMWARE hints
ASoC: Intel: avs: Fix possible null-ptr-deref when initing hw
ASoC: Intel: avs: Fix PPLCxFMT calculation
ASoC: Intel: avs: Fix deadlock when the failing IPC is SET_D0IX
ASoC: codecs: hda: Fix RPM usage count underflow
ASoC: amd: yc: Add support for Lenovo Yoga 7 16ARP8
ASoC: tas571x: fix tas5733 num_controls
...
Linus Torvalds [Sat, 7 Jun 2025 14:24:07 +0000 (07:24 -0700)]
Merge tag 'ubifs-for-linus-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull JFFS2 and UBIFS fixes from Richard Weinberger:
"JFFS2:
- Correctly check return code of jffs2_prealloc_raw_node_refs()
UBIFS:
- Spelling fixes"
* tag 'ubifs-for-linus-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
jffs2: check jffs2_prealloc_raw_node_refs() result in few other places
jffs2: check that raw node were preallocated before writing summary
ubifs: Fix grammar in error message
Mike Rapoport [Sat, 17 May 2025 09:30:48 +0000 (12:30 +0300)]
sh: kprobes: Remove unused variables in kprobe_exceptions_notify()
kbuild reports the following warning:
arch/sh/kernel/kprobes.c: In function 'kprobe_exceptions_notify':
>> arch/sh/kernel/kprobes.c:412:24: warning: variable 'p' set but not used [-Wunused-but-set-variable]
412 | struct kprobe *p = NULL;
| ^
The variable 'p' is indeed unused since the commit fa5a24b16f94
("sh/kprobes: Don't call the ->break_handler() in SH kprobes code")
Remove that variable along with 'kprobe_opcode_t *addr' which also
becomes unused after 'p' is removed.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202505151341.EuRFR22l-lkp@intel.com/ Fixes: fa5a24b16f94 ("sh/kprobes: Don't call the ->break_handler() in SH kprobes code") Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org> Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
projects / thirdparty / kernel / linux.git / log
