The bridge might miss the display change events when it's powered off.
This happens when a user changes the external monitor when the system
is suspended and the embedded controller doesn't not wake AP up.
It's also observed that one DP-to-HDMI bridge doesn't work correctly
when there is no EDID read after it is powered on.
Drop the cache to force an EDID read after system resume to fix this.
Fixes: 11feaef69d0c ("drm/bridge: it6505: Add caching for EDID") Signed-off-by: Pin-yen Lin <treapking@chromium.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240926092931.3870342-3-treapking@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The bridge might miss the display change events when it's powered off.
This happens when a user changes the external monitor when the system
is suspended and the embedded controller doesn't not wake AP up.
It's also observed that one DP-to-HDMI bridge doesn't work correctly
when there is no EDID read after it is powered on.
Drop the cache to force an EDID read after system resume to fix this.
Fixes: 8bdfc5dae4e3 ("drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP") Signed-off-by: Pin-yen Lin <treapking@chromium.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240926092931.3870342-2-treapking@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The DT bindings deprecated the "hp-det-gpio" and "mic-det-gpio"
properties in favor of "hp-det-gpios" and "mic-det-gpios", but the
driver was never updated to support the latter.
Even before, there existed users of "hp-det-gpios" and "mic-det-gpios".
While this may have been handled fine by the ASoC core, this was missed
by the Freescale-specific part.
Fixes: 4189b54220e5af15 ("ASoC: dt-bindings: fsl-asoc-card: convert to YAML") Fixes: 40ba2eda0a7b727f ("arm64: dts: imx8mm-nitrogen-r2: add audio") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://patch.msgid.link/dbcb5bfea005a468ec6dc38374fe6d02bc693c22.1727438777.git.geert+renesas@glider.be Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some fix and updates in the following items:
1. examples:
Update generic node name to 'audio-codec' to comply with the
coming change in 'mt6359.dtsi'. This change is necessary to fix the
dtbs_check error:
pmic: 'mt6359codec' does not match any of the regexes: 'pinctrl-[0-9]+'
2. mediatek,dmic-mode:
After inspecting the .dts and .dtsi files using 'mt6359-codec', it was
discovered that the definitions of 'two wires' and 'one wire' are
inverted compared to the DT schema.
For example, the following boards using MT6359 PMIC:
- mt8192-asurada.dtsi
- mt8195-cherry.dtsi
These boards use the same definitions of 'dmic-mode' as other boards
using MT6358 PMIC. The meaning of '0' or '1' has been noted as comments
in the device trees.
Upon examining the code in [1] and [2], it was confirmed that the
definitions of 'dmic-mode' are consistent between "MT6359 PMIC" and
"MT6358 PMIC". Therefore, the DT Schema should be correct as is.
In supported_vht_mcs_rate_nss2, the rate for MCS9 & VHT20 is defined as
{1560, 1733}, this does not align with firmware's definition and therefore
fails the verification in ath10k_mac_get_rate_flags_vht():
invalid vht params rate 1730 100kbps nss 2 mcs 9
and:
invalid vht params rate 1920 100kbps nss 2 mcs 9
Change it to {1730, 1920} to align with firmware to fix the issue.
Since ath10k_hw_params::supports_peer_stats_info is enabled only for
QCA6174, this change does not affect other chips.
In supported_vht_mcs_rate_nss1, the rate for MCS9 & VHT20 is defined as
{780, 867}, this does not align with firmware's definition and therefore
fails the verification in ath10k_mac_get_rate_flags_vht():
invalid vht params rate 960 100kbps nss 1 mcs 9
Change it to {865, 960} to align with firmware, so this issue could be
fixed.
Since ath10k_hw_params::supports_peer_stats_info is enabled only for
QCA6174, this change does not affect other chips.
EXTERNAL_REG_INTERNAL_OFFSET/EXTERNAL_REG_WRITE_ADDR should be used in
pairs. If an external register shouldn't be written, both packets
shouldn't be sent.
Fixes: a78b48146972 ("drm/amdgpu: Skip PCTL0_MMHUB_DEEPSLEEP_IB write in jpegv4.0.3 under SRIOV") Signed-off-by: Lijo Lazar <lijo.lazar@amd.com> Acked-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We must first flush the MMU cache and then, flush the TLB, not the other
way around. Currently, we can see a race condition between the MMU cache
and the TLB when running multiple rendering processes at the same time.
This is evidenced by MMU errors triggered by the IRQ.
Fix the MMU flush order by flushing the MMU cache and then the TLB.
Also, in order to address the race condition, wait for the MMU cache flush
to finish before starting the TLB flush.
The commit introducing the Frida display started to write the
SETVCMOFF registers unconditionally, and some (not all!) Hydis
display seem to be affected by ghosting after the commit.
Make SETVCMOFF optional and only send these commands on the
Frida display for now.
Reported-by: Stefan Hansson <newbyte@postmarketos.org> Fixes: 219a1f49094f ("drm/panel: nt35510: support FRIDA FRD400B25025-A-CTK") Acked-by: Jessica Zhang <quic_jesszhan@quicinc.com> Tested-by: Stefan Hansson <newbyte@postmarketos.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240908-fix-nt35510-v2-1-d4834b9cdb9b@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Fixes: 47b1be5c0f4e ("staging: imx/drm: request irq only after adding the crtc") Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Link: https://patchwork.freedesktop.org/patch/msgid/20240912083020.3720233-4-ruanjinjie@huawei.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Fixes: 9021c317b770 ("drm/imx: Add initial support for DCSS on iMX8MQ") Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> Reviewed-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240912083020.3720233-2-ruanjinjie@huawei.com
[DB: fixed the subject] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Because MAX_PAGE_ORDER, kmalloc can max alloc 4096 * (1 << 10), 4MB
memory, each array entry is pointer(8byte), so can save 524288 pages(2GB).
Further more, costly order(order 3) may not be guaranteed that it can be
applied for, due to fragmentation.
This patch change udmabuf array use kvmalloc_array, this can fallback
alloc into vmalloc, which can guarantee allocation for any size and does
not affect the performance of kmalloc allocations.
Signed-off-by: Huan Yang <link@vivo.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Vivek Kasireddy <vivek.kasireddy@intel.com> Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240918025238.2957823-3-link@vivo.com
Stable-dep-of: 18d7de823b71 ("udmabuf: fix vmap_udmabuf error page set") Signed-off-by: Sasha Levin <sashal@kernel.org>
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Fixes: 853402a00823 ("mwifiex: Enable WoWLAN for both sdio and pcie") Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> Acked-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20240910124314.698896-3-ruanjinjie@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
omap_gem_new_dmabuf() creates the new gem object, and then takes and
holds the omap_obj->lock for the rest of the function. This has two
issues:
- omap_gem_free_object(), which is called in the error paths, also takes
the same lock, leading to deadlock
- Even if the above wouldn't happen, in the error cases
omap_gem_new_dmabuf() still unlocks omap_obj->lock, even after the
omap_obj has already been freed.
Furthermore, I don't think there's any reason to take the lock at all,
as the object was just created and not yet shared with anyone else.
To fix all this, drop taking the lock.
Fixes: 3cbd0c587b12 ("drm/omap: gem: Replace struct_mutex usage with omap_obj private lock") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/all/511b99d7-aade-4f92-bd3e-63163a13d617@stanley.mountain/ Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240806-omapdrm-misc-fixes-v1-3-15d31aea0831@ideasonboard.com Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/gpu/drm/omapdrm/dss/base.c:176 omapdss_device_disconnect() error: we previously assumed 'src' could be null (see line 169)
This code is mostly from a time when omapdrm had its own display device
model. I can't honestly remember the details, and I don't think it's
worth digging in deeply into that for a legacy driver.
However, it looks like we only call omapdss_device_disconnect() and
omapdss_device_connect() with NULL as the src parameter. We can thus
drop the src parameter from both functions, and fix the smatch warning.
I don't think omapdss_device_disconnect() ever gets NULL for the dst
parameter (if it did, we'd crash soon after returning from the
function), but I have kept the !dst check, just in case, but I added a
WARN_ON() there.
Also, if the dst parameter can be NULL, we can't always get the struct
dss_device pointer from dst->dss (which is only used for a debug print).
To make sure we can't hit that issue, do it similarly to the
omapdss_device_connect() function: add 'struct dss_device *dss' as the
first parameter, so that we always have it regardless of the dst.
UBSAN: array-index-out-of-bounds in drivers/net/wireless/ath/ath9k/htc_hst.c:26:51
index 255 is out of range for type 'htc_endpoint [22]'
CPU: 0 UID: 0 PID: 8 Comm: kworker/0:0 Not tainted 6.11.0-rc6-dirty #14
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
Workqueue: events request_firmware_work_func
Call Trace:
<TASK>
dump_stack_lvl+0x180/0x1b0
__ubsan_handle_out_of_bounds+0xd4/0x130
htc_issue_send.constprop.0+0x20c/0x230
? _raw_spin_unlock_irqrestore+0x3c/0x70
ath9k_wmi_cmd+0x41d/0x610
? mark_held_locks+0x9f/0xe0
...
Since this bug has been confirmed to be caused by insufficient verification
of conn_rsp_epid, I think it would be appropriate to add a range check for
conn_rsp_epid to htc_connect_service() to prevent the bug from occurring.
Fixes: fb9987d0f748 ("ath9k_htc: Support for AR9271 chipset.") Signed-off-by: Jeongjun Park <aha310510@gmail.com> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20240909103855.68006-1-aha310510@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When factoring out __vc4_hvs_stop_channel, the logic got inverted from
if (condition)
// stop channel
to
if (condition)
goto out
//stop channel
out:
and also changed the exact register writes used to stop the channel.
Correct the logic so that the channel is actually stopped, and revert
to the original register writes.
The debug function to display the dlists didn't reset next_entry_start
when starting each display, so resulting in not stopping the
list at the correct place.
Trying to read /sys/kernel/debug/dri/1/hdmi1_regs
when the hdmi is disconnected results in a fatal system hang.
This is due to the pm suspend code disabling the dvp clock.
That is just a gate of the 108MHz clock in DVP_HT_RPI_MISC_CONFIG,
which results in accesses hanging AXI bus.
Protect against this.
Fixes: 25eb441d55d4 ("drm/vc4: hdmi: Add all the vc5 HDMI registers into the debugfs dumps") Signed-off-by: Dom Cobley <popcornmix@gmail.com> Reviewed-by: Maxime Ripard <mripard@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240621152055.4180873-17-dave.stevenson@raspberrypi.com Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The INTERVAL_TREE_DEFINE() uncoditionally provides a bunch of helper
functions which in some cases may be not used. This, in particular,
prevents kernel builds with clang, `make W=1` and CONFIG_WERROR=y:
I missed this open-coded kref_get() while trying to debug a refcount
bug, so let's use the helper function here to avoid that waste of time
again in the future.
When an error occurs in sysfs show callback, we should return the errno
directly instead of formatting it as the result, which produces
meaningless output and doesn't inform the userspace of the error.
Fixes: 468f96bfa3a0 ("platform/x86: panasonic-laptop: Add support for battery charging threshold (eco mode)") Fixes: d5a81d8e864b ("platform/x86: panasonic-laptop: Add support for optical driver power in Y and W series") Signed-off-by: Yao Zi <ziyao@disroot.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20241118064637.61832-3-ziyao@disroot.org Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
And the issue seems to be that the corresponding devres group is not
allocated. Normally, devres_open_group() is called from
__hid_device_probe() but Hyper-V HID driver overrides 'hid_dev->driver'
with 'mousevsc_hid_driver' stub and basically re-implements
__hid_device_probe() by calling hid_parse() and hid_hw_start() but not
devres_open_group(). hid_device_probe() does not call __hid_device_probe()
for it. Later, when the driver is removed, hid_device_remove() calls
devres_release_group() as it doesn't check whether hdev->driver was
initially overridden or not.
The issue seems to be related to the commit 62c68e7cee33 ("HID: ensure
timely release of driver-allocated resources") but the commit itself seems
to be correct.
Fix the issue by dropping the 'hid_dev->driver' override and using
hid_register_driver()/hid_unregister_driver() instead. Alternatively, it
would have been possible to rely on the default handling but
HID_CONNECT_DEFAULT implies HID_CONNECT_HIDRAW and it doesn't seem to work
for mousevsc as-is.
Correct the audio name for the Indiedroid Nova from
rockchip,es8388-codec to rockchip,es8388. This name change corrects a
kernel log error of "ASoC: driver name too long 'rockchip,es8388-codec'
-> 'rockchip_es8388'".
Fixes: 3900160e164b ("arm64: dts: rockchip: Add Indiedroid Nova board") Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Link: https://lore.kernel.org/r/20241031150505.967909-2-macroalpha82@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In ia_css_3a_statistics_allocate(), there is no check on the allocation
result of the rgby_data memory. If rgby_data is not successfully
allocated, it may trigger the assert(host_stats->rgby_data) assertion in
ia_css_s3a_hmem_decode(). Adding a check to fix this potential issue.
Fixes: a49d25364dfb ("staging/atomisp: Add support for the Intel IPU v2") Signed-off-by: Li Huafei <lihuafei1@huawei.com> Reviewed-by: Andy Shevchenko <andy@kernel.org> Link: https://lore.kernel.org/r/20241104145051.3088231-1-lihuafei1@huawei.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some PWM hardwares (e.g. MC33XS2410) cannot implement a zero duty cycle
but can instead disable the hardware which also results in a constant
inactive output.
There are some checks (enabled with CONFIG_PWM_DEBUG) to help
implementing a driver without violating the normal rounding rules. Make
them less strict to let above described hardware pass without warning.
DMA ops are a helper for architectures and not for drivers to override the
DMA implementation. Driver should not override the DMA implementation.
This patch removes the dma_ops override from auxiliary device and adds
driver-internal helpers that use the actual DMA mapping APIs.
Fixes: 9163d83573e4 ("media: intel/ipu6: add IPU6 DMA mapping API and MMU table") Signed-off-by: Bingbu Cao <bingbu.cao@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
[Sakari Ailus: Fix the commit message a little.] Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix printing DMA and physical address printing on 32-bit platforms, by
using correct types. Also cast DMA_BIT_MASK() result to dma_addr_t to make
Clang happy.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Bingbu Cao <bingbu.cao@intel.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Stable-dep-of: daabc5c64703 ("media: ipu6: not override the dma_ops of device in driver") Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a kernel crash with the below call trace when the SCPI firmware
returns OPP count of zero.
dvfs_info.opp_count may be zero on some platforms during the reboot
test, and the kernel will crash after dereferencing the pointer to
kcalloc(info->count, sizeof(*opp), GFP_KERNEL).
Fixes: 8cb7cf56c9fe ("firmware: add support for ARM System Control and Power Interface(SCPI) protocol") Signed-off-by: Luo Qiu <luoqiu@kylinsec.com.cn>
Message-Id: <55A2F7A784391686+20241101032115.275977-1-luoqiu@kylinsec.com.cn> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MBM and MBA tests need to discover the event and umask with which to
configure the performance event used to measure read memory bandwidth.
This is done by parsing the
/sys/bus/event_source/devices/uncore_imc_<imc instance>/events/cas_count_read
file for each iMC instance that contains the formatted
output: "event=<event>,umask=<umask>"
Parsing of cas_count_read contents is done by initializing an array of
MAX_TOKENS elements with tokens (deliminated by "=,") from this file.
Remove the unnecessary append of a delimiter to the string needing to be
parsed. Per the strtok() man page: "delimiter bytes at the start or end of
the string are ignored". This has no impact on the token placement within
the array.
After initialization, the actual event and umask is determined by
parsing the tokens directly following the "event" and "umask" tokens
respectively.
Iterating through the array up to index "i < MAX_TOKENS" but then
accessing index "i + 1" risks array overrun during the final iteration.
Avoid array overrun by ensuring that the index used within for
loop will always be valid.
Fixes: 1d3f08687d76 ("selftests/resctrl: Read memory bandwidth from perf IMC counter and from resctrl file system") Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
alloc_buffer() allocates and initializes (with random data) a
buffer of requested size. The initialization starts from the beginning
of the allocated buffer and incrementally assigns sizeof(uint64_t) random
data to each cache line. The initialization uses the size of the
buffer to control the initialization flow, decrementing the amount of
buffer needing to be initialized after each iteration.
The size of the buffer is stored in an unsigned (size_t) variable s64
and the test "s64 > 0" is used to decide if initialization is complete.
The problem is that decrementing the buffer size may wrap around
if the buffer size is not divisible by "CL_SIZE / sizeof(uint64_t)"
resulting in the "s64 > 0" test being true and memory beyond the buffer
"initialized".
Use a signed value for the buffer size to support all buffer sizes.
Fixes: a2561b12fe39 ("selftests/resctrl: Add built in benchmark") Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
By default the MBM test uses the "fill_buf" benchmark to keep reading
from a buffer with size DEFAULT_SPAN while measuring memory bandwidth.
User space can provide an alternate benchmark or amend the size of
the buffer "fill_buf" should use.
Analysis of the MBM measurements do not require that a buffer be used
and thus do not require knowing the size of the buffer if it was used
during testing. Even so, the buffer size is printed as informational
as part of the MBM test results. What is printed as buffer size is
hardcoded as DEFAULT_SPAN, even if the test relied on another benchmark
(that may or may not use a buffer) or if user space amended the buffer
size.
Ensure that accurate buffer size is printed when using "fill_buf"
benchmark and omit the buffer size information if another benchmark
is used.
When the fixed regulators for the LCD panel and DP bridge were added,
their supplies were not modeled in. These, except for the 1.0V supply,
are just load switches, and need and have a supply.
Add the supplies for each of the fixed regulators.
Some of the regulator supplies for the MIPI-DPI-to-DP bridge and their
associated nodes are incorrectly named. In particular, the 1.0V supply
was modeled as a 1.2V supply.
Fix all the incorrect names, and also fix the voltage of the 1.0V
regulator.
Fix DTBS check errors for 'mt6358codec' and 'mt6358regulator':
Error message is:
pmic: 'mt6358codec' and 'mt6358regulator' does not match any of the
regexes: 'pinctrl-[0-9]+'.
Rename these two device node to generic 'audio-codec' and 'regulators'.
Fixes: 9f8872221674 ("arm64: dts: mt6358: add PMIC MT6358 related nodes") Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com> Link: https://lore.kernel.org/r/20241029064647.13370-1-macpaul.lin@mediatek.com Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add support for the ADC on MT6357/8/9 and keep it default enabled
as this IP is always present on those PMICs.
Users may use different IIO channels depending on board-specific
routing.
Fix the issue where both 'output-low' and 'output-high' exist under GPIO
hog nodes (rst_usb_hub_hog and sel_usb_hub_hog) when applying device
tree overlays. Since /delete-property/ is not supported in the overlays,
setting 'output-low' results in both properties being present. The
workaround is to disable these hogs and create new ones with 'output-low'
as needed.
Fix below CHECK_DTBS warning:
arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtb: sel-usb-hub-hog:
{'output-low': True, 'gpio-hog': True, 'gpios': [[1, 0]], 'output-high': True, 'phandle': 108, '$nodename': ['sel-usb-hub-hog']}
is valid under each of {'required': ['output-low']}, {'required': ['output-high']
Fixes: 3f6fc30abebc ("arm64: dts: imx8mn: tqma8mqnl-mba8mx: Add USB DR overlay") Signed-off-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
"#sound-dai-cells" is required if the board is using "simple-card".
However, the HiHope board uses "audio-graph", thus remove the unneeded
`#sound-dai-cells`.
Commit 9e72606cd2db ("arm64: dts: renesas: #sound-dai-cells is used when
simple-card") updated the comment regarding usage of "#sound-dai-cells"
in the SoC DTSI but missed to remove "#sound-dai-cells" from board DTS
files.
Lockdep gives a false positive splat as it can't distinguish the lock
which is taken by different IRQ descriptors from different IRQ chips
that are organized in a way of a hierarchy:
======================================================
WARNING: possible circular locking dependency detected 6.12.0-rc5-next-20241101-00148-g9fabf8160b53 #562 Tainted: G W
------------------------------------------------------
modprobe/141 is trying to acquire lock: ffff899446947868 (intel_soc_pmic_bxtwc:502:(&bxtwc_regmap_config)->lock){+.+.}-{4:4}, at: regmap_update_bits_base+0x33/0x90
but task is already holding lock: ffff899446947c68 (&d->lock){+.+.}-{4:4}, at: __setup_irq+0x682/0x790
A shift-out-of-bounds issue was identified by UBSAN in the
tegra_qspi_fill_tx_fifo_from_client_txbuf() function.
UBSAN: shift-out-of-bounds in drivers/spi/spi-tegra210-quad.c:345:27
shift exponent 32 is too large for 32-bit type 'u32' (aka 'unsigned int')
Call trace:
tegra_qspi_start_cpu_based_transfer
The problem arises when shifting the contents of tx_buf left by 8 times
the value of i, which can exceed 4 and result in an exponent larger than
32 bits.
Resolve this by restrict the value of i to be less than 4, preventing
the shift operation from overflowing.
Signed-off-by: Breno Leitao <leitao@debian.org> Fixes: 921fc1838fb0 ("spi: tegra210-quad: Add support for Tegra210 QSPI controller") Link: https://patch.msgid.link/20241004125400.1791089-1-leitao@debian.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
__pa() is only intended to be used for linear map addresses and using
it for initial_boot_params which is in fixmap for arm64 will give an
incorrect value. Hence save the physical address when it is known at
boot time when calling early_init_dt_scan for arm64 and use it at kexec
time instead of converting the virtual address using __pa().
Note that arm64 doesn't need the FDT region reserved in the DT as the
kernel explicitly reserves the passed in FDT. Therefore, only a debug
warning is fixed with this change.
Reported-by: Breno Leitao <leitao@debian.org> Suggested-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Usama Arif <usamaarif642@gmail.com> Fixes: ac10be5cdbfa ("arm64: Use common of_kexec_alloc_and_setup_fdt()") Link: https://lore.kernel.org/r/20241023171426.452688-1-usamaarif642@gmail.com Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Both drivers use I/O port accesses without declaring a dependency on
CONFIG_HAS_IOPORT. For sbc8360_wdt this causes a compile error on UML
once inb()/outb() helpers become conditional.
For sbc7240_wdt this causes no such errors with UML because this driver
depends on both x86_32 and !UML. Nevertheless add HAS_IOPORT as
a dependency for both drivers to be explicit and drop the !UML
dependency for sbc7240_wdt as it is now redundant since UML implies no
HAS_IOPORT.
The clock IDs for multiple MCSPI instances across wakeup domain
in J721s2 are incorrect when compared with documentation [1]. Fix the
clock IDs to their appropriate values.
The clock IDs for multiple MCSPI instances across wakeup domain
in J721e are incorrect when compared with documentation [1]. Fix
the clock ids to their appropriate values.
The clock IDs for multiple MCSPI instances across wakeup as
well as main domain in J7200 are incorrect when compared with
documentation [1]. This results in kernel crashes when the said
instances are enabled. Fix the clock ids to their appropriate
values.
Commit 0d0a0b441346 ("arm64: dts: ti: k3-j7200: fix main pinmux
range") split the main_pmx0 into two nodes: main_pmx0 and main_pmx1
due to a non-addressable region, but incorrectly represented the
ranges. As a result, the memory map for the pinctrl is incorrect. Fix
this by introducing the correct ranges.
The ranges are taken from the J7200 TRM [1] (Table 5-695. CTRL_MMR0
Registers).
Padconfig starting addresses and ranges:
- 0 to 66: 0x11c000, 0x10c
- 68: 0x11c110, 0x004
- 71 to 73: 0x11c11c, 0x00c
- 89 to 90: 0x11c164, 0x008
The datasheet [2] doesn't contain PADCONFIG63 (Table 6-106. Pin
Multiplexing), but the pin is necessary for enabling the MMC1 CLKLP
pad loopback and should be included in the pinmux register map.
Due to the change in pinmux node addresses, change the pinmux node for
the USB0_DRVVBUS pin to main_pmx2. The offset has not changed since the
new main_pmx2 node has the same base address and range as the original
main_pmx1 node. All other pinmuxing done within J7200 dts or dtso files
only uses main_pmx0 which has not changed.
The DCDC5 voltage rail in the X-Powers AXP809 PMIC has a resolution of
50mV, so the currently enforced limits of 1.475 and 1.525 volts cannot
be set, when the existing regulator value is beyond this range.
This will lead to the whole regulator driver to give up and fail
probing, which in turn will hang the system, as essential devices depend
on the PMIC.
In this case a bug in U-Boot set the voltage to 1.75V (meant for DCDC4),
and the AXP driver's attempt to correct this lead to this error:
==================
[ 4.447653] axp20x-rsb sunxi-rsb-3a3: AXP20X driver loaded
[ 4.450066] vcc-dram: Bringing 1750000uV into 1575000-1575000uV
[ 4.460272] vcc-dram: failed to apply 1575000-1575000uV constraint: -EINVAL
[ 4.474788] axp20x-regulator axp20x-regulator.0: Failed to register dcdc5
[ 4.482276] axp20x-regulator axp20x-regulator.0: probe with driver axp20x-regulator failed with error -22
==================
Set the limits to values that can be programmed, so any correction will
be successful.
Implement workaround for ERR051198
(https://www.nxp.com/docs/en/errata/IMX8MN_0N14Y.pdf)
PWM output may not function correctly if the FIFO is empty when a new SAR
value is programmed.
Description:
When the PWM FIFO is empty, a new value programmed to the PWM Sample
register (PWM_PWMSAR) will be directly applied even if the current timer
period has not expired. If the new SAMPLE value programmed in the
PWM_PWMSAR register is less than the previous value, and the PWM counter
register (PWM_PWMCNR) that contains the current COUNT value is greater
than the new programmed SAMPLE value, the current period will not flip
the level. This may result in an output pulse with a duty cycle of 100%.
Workaround:
Program the current SAMPLE value in the PWM_PWMSAR register before
updating the new duty cycle to the SAMPLE value in the PWM_PWMSAR
register. This will ensure that the new SAMPLE value is modified during
a non-empty FIFO, and can be successfully updated after the period
expires.
Write the old SAR value before updating the new duty cycle to SAR. This
avoids writing the new value into an empty FIFO.
This only resolves the issue when the PWM period is longer than 2us
(or <500kHz) because write register is not quick enough when PWM period is
very short.
Reproduce steps:
cd /sys/class/pwm/pwmchip1/pwm0
echo 2000000000 > period # It is easy to observe by using long period
echo 1000000000 > duty_cycle
echo 1 > enable
echo 8000 > duty_cycle # One full high pulse will be seen by scope
Fixes: 166091b1894d ("[ARM] MXC: add pwm driver for i.MX SoCs") Reviewed-by: Jun Li <jun.li@nxp.com> Signed-off-by: Clark Wang <xiaoning.wang@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20241008194123.1943141-1-Frank.Li@nxp.com Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'enable-active-low' property is not a valid, because it is the
default behaviour of the fixed regulator.
Only 'enable-active-high' is valid, and when this property is absent
the fixed regulator will act as active low by default.
Both the rk3588-orange-pi-5 and the Wolfvision pf5 io expander overlay
smuggled those enable-active-low properties in, so remove them to
make dtbscheck happier.
This driver uses various OF-specific functions and depends on phandle
parsing. There's no reason to make it available to non-OF systems so add
a relevant dependency switch to its Kconfig entry.
Fixes: 2f1630f437df ("power: pwrseq: add a driver for the PMU module on the QCom WCN chipsets") Link: https://lore.kernel.org/r/20241004130449.51725-1-brgl@bgdev.pl Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rk808-regulator driver supports multiple PMIC variants from the Rockckip
RK80x and RK81x series, but the DVS GPIOs are supported on the RK808 variant
only, according to the DT bindings [1][2][3][4][5][6] and the datasheets for
the supported PMIC variants. [7][8][9][10][11][12]
Thus, change the probe path so the "dvs-gpios" property is checked for and
its value possibly used only when the handled PMIC variant is RK808. There's
no point in doing that on the other PMIC variants, because they don't support
the DVS GPIOs, and it goes against the DT bindings to allow a possible out-
of-place "dvs-gpios" property to actually be handled in the driver.
This eliminates the following messages, emitted when the "dvs-gpios" property
isn't found in the DT, from the kernel log on boards that actually don't use
the RK808 variant, which may have provided a source of confusion:
rk808-regulator rk808-regulator.2.auto: there is no dvs0 gpio
rk808-regulator rk808-regulator.2.auto: there is no dvs1 gpio
Furthermore, demote these kernel messages to debug messages, because they are
useful during the board bringup phase only. Emitting them afterwards, on the
boards that use the RK808 variant, but actually don't use the DVS0/1 GPIOs,
clutters the kernel log a bit, while they provide no value and may actually
cause false impression that some PMIC-related issues are present.
Only cgroup v2 can be attached by bpf programs, so this patch introduces
that cgroup_bpf_inherit and cgroup_bpf_offline can only be called in
cgroup v2, and this can fix the memleak mentioned by commit 04f8ef5643bc
("cgroup: Fix memory leak caused by missing cgroup_bpf_offline"), which
has been reverted.
Fixes: 2b0d3d3e4fcf ("percpu_ref: reduce memory footprint of percpu_ref in fast path") Fixes: 4bfc0bb2c60e ("bpf: decouple the lifetime of cgroup_bpf from cgroup itself") Link: https://lore.kernel.org/cgroups/aka2hk5jsel5zomucpwlxsej6iwnfw4qu5jkrmjhyfhesjlfdw@46zxhg5bdnr7/ Signed-off-by: Chen Ridong <chenridong@huawei.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Only cgroup v2 can be attached by cgroup by BPF programs. Revert this
commit and cgroup_bpf_inherit and cgroup_bpf_offline won't be called in
cgroup v1. The memory leak issue will be fixed with next patch.
The RT5682i and RT5682s drivers describe two DAIs: AIF1 supports both
playback and capture, while AIF2 supports capture only.
Cherry doesn't specify which DAI to use. Although this doesn't cause
real issues because AIF1 happens to be the first DAI, it should be
corrected:
codec@1a: #sound-dai-cells: 1 was expected
Update #sound-dai-cells to 1 and adjust DAI link usages accordingly.
Fixes: 87728e3ccf35 ("arm64: dts: mediatek: mt8195-cherry: Specify sound DAI links and routing") Signed-off-by: Fei Shao <fshao@chromium.org> Link: https://lore.kernel.org/r/20241021114318.1358681-1-fshao@chromium.org Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The T-PHY controller at 0x11e40000 controls two underlying USB2 and USB3
PHY ports. The USB3 port works normally just like the others, so there's
no point in disabling it separately. Otherwise, board DTs would have to
enable both the T-PHY controller and one of its sub-nodes in particular,
which is slightly redundant and confusing.
Remove the status line in the u3port1 node, so it's ready to be used
once the T-PHY controller is enabled.
Fixes: 9461e0caac9e ("arm64: dts: Add MediaTek MT8188 dts and evaluation board and Makefile") Signed-off-by: Fei Shao <fshao@chromium.org> Link: https://lore.kernel.org/r/20241021081311.543625-1-fshao@chromium.org Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Hana device has a second source option trackpad, but it is missing
its regulator supply. It only works because the regulator is marked as
always-on.
Add the regulator supply, but leave out the post-power-on delay. Instead,
document the post-power-on delay along with the reason for not adding
it in a comment.
Fixes: 689b937bedde ("arm64: dts: mediatek: add mt8173 elm and hana board") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20241018082001.1296963-1-wenst@chromium.org Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function ub960_rxport_read is being called and afterwards ret is
being checked for any failures, however ret is not being assigned to
the return of the function call. Fix this by assigning ret to the
return of the call which appears to be missing.
Fixes: afe267f2d368 ("media: i2c: add DS90UB960 driver") Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
efi_convert_cmdline() always returns a size of at least 1 because it
counts the NUL terminator, so the "cmdline_size == 0" condition is never
satisfied.
Change it to check if the string starts with a NUL character to get the
intended behavior: to use CONFIG_CMDLINE when load_options_size == 0.
Fixes: 60f38de7a8d4 ("efi/libstub: Unify command line param parsing") Signed-off-by: Jonathan Marek <jonathan@marek.ca> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
With commit 53c98e35dcbc ("openrisc: mm: remove unneeded early ioremap
code") it was commented that early ioremap was not used in OpenRISC. I
acked this but was wrong, earlycon was using it. Earlycon setup now
fails with the below trace:
To fix this we could either implement early_ioremap again or implement
fixmap. In this patch we choose the later option of implementing basic
fixmap support.
While fixing this we also remove the old FIX_IOREMAP slots that were
used by early ioremap code. That code was also removed by commit 53c98e35dcbc ("openrisc: mm: remove unneeded early ioremap code") but
these definitions were not cleaned up.
The section counter tracks how many sections of kernel-doc were added.
The only real use of the counter value is to check if anything was
actually supposed to be output and give a warning is nothing is
available.
The current logic of remembering the initial value and then resetting
the value then when processing each file means that if a file has the
same number of sections as the previously processed one, a warning is
incorrectly given.
GCC 13 complains about the truncated output of snprintf():
drivers/mmc/host/mmc_spi.c: In function ‘mmc_spi_response_get’:
drivers/mmc/host/mmc_spi.c:227:64: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
227 | snprintf(tag, sizeof(tag), " ... CMD%d response SPI_%s",
| ^
drivers/mmc/host/mmc_spi.c:227:9: note: ‘snprintf’ output between 26 and 43 bytes into a destination of size 32
227 | snprintf(tag, sizeof(tag), " ... CMD%d response SPI_%s",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
228 | cmd->opcode, maptype(cmd));
Drop it and fold the string it generates into the only place where it's
emitted - the dev_dbg() call at the end of the function.
Add the atmel,usart-mode property to the UART nodes. This ensures
compliance with the atmel,at91-usart.yaml schema and resolves the errors
below:
serial@200: $nodename:0: 'serial@200' does not match
'^spi(@.*|-([0-9]|[1-9][0-9]+))?$'
serial@200: atmel,use-dma-rx: False schema does not allow True
serial@200: atmel,use-dma-tx: False schema does not allow True
serial@200: atmel,fifo-size: False schema does not allow [[16]]
These errors indicate that the property
atmel,usart-mode = <AT91_USART_MODE_SERIAL> is missing for
UART nodes 0, 1, 2, 3, 4, 6, 7, 8, 9, 10, 11, and 12.
Fixes: 99c808335877 ("ARM: dts: at91: sam9x60: Add missing flexcom definitions") Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Andrei Simion <andrei.simion@microchip.com> Link: https://lore.kernel.org/r/20240912093307.40488-1-andrei.simion@microchip.com
[claudiu.beznea: move the atmel,usart-mode close to vendor specific
properties to cope with DTS coding style] Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev> Signed-off-by: Sasha Levin <sashal@kernel.org>
L10A, being a fixed regulator, should have min_voltage = max_voltage,
otherwise fixed rulator fails to probe. Fix the max_voltage range to be
equal to minimum.
This loop is supposed to break if the frequency returned from
clk_round_rate() is the same as on the previous iteration. However,
that check doesn't make sense on the first iteration through the loop.
It leads to reading before the start of these->clk_perf_tbl[] array.
If request_irq() fails in sr_late_init(), there is no need to enable
the irq, and if it succeeds, disable_irq() after request_irq() still has
a time gap in which interrupts can come.
request_irq() with IRQF_NO_AUTOEN flag will disable IRQ auto-enable when
request IRQ.
The mutex node in mt8195.dtsi was triggering a dtbs_check error:
mutex@1c101000: 'clock-names', 'reg-names' do not match any of the
regexes: 'pinctrl-[0-9]+'
This seems no need by inspecting the DT schemas and other reference boards,
so drop 'clock-names' and 'reg-names' in mt8195.dtsi.
Fixes: 92d2c23dc269 ("arm64: dts: mt8195: add display node for vdosys1") Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20241002051620.2050-4-macpaul.lin@mediatek.com Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ethernet-phy node in mt8395-genio-1200-evk.dts was triggering a
dtbs_check error. The error message was:
eth-phy0@1: $nodename:0: 'eth-phy0@1' does not match
'^ethernet-phy(@[a-f0-9]+)?$'
Fix this issue by replacing 'eth-phy' node to generic 'ethernet-phy'.
Fixes: f2b543a191b6 ("arm64: dts: mediatek: add device-tree for Genio 1200 EVK board") Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20241002051620.2050-3-macpaul.lin@mediatek.com Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The clock index "CLK_APMIXED_MFGPLL" belongs to the "apmixedsys" provider,
so fix the index.
In addition, add a "mfg1" label so following commits could set
domain-supply for MFG1 power domain.
Fixes: eaf73e4224a3 ("arm64: dts: mediatek: mt8188: Add support for SoC power domains") Signed-off-by: Pablo Sun <pablo.sun@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20241002022138.29241-2-pablo.sun@mediatek.com Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When TMR_MANAGER is enabled as module there is a need to export functions
which are present in architecture code.
It has been found by running:
make W=1 C=1 allmodconfig
sed -i -e 's/WERROR=y/WERROR=n/g' .config
make C=1 W=1
which errors out like this:
ERROR: modpost: "xmb_manager_register" [drivers/misc/xilinx_tmr_manager.ko] undefined!
ERROR: modpost: "xmb_inject_err" [drivers/misc/xilinx_tmr_inject.ko] undefined!
If we fail to allocate memory for cb_data by kmalloc, the memory
allocation for eve_data is never freed, add the missing kfree()
in the error handling path.
Fixes: 05e5ba40ea7a ("driver: soc: xilinx: Add support of multiple callbacks for same event in event management driver") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Link: https://lore.kernel.org/r/20240706065155.452764-1-cuigaosheng1@huawei.com Signed-off-by: Michal Simek <michal.simek@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
