Merge tag 'sunxi-dt-for-7.1-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/dt
Allwinner Device Tree Changes for 7.1 - Part 2
UART DMA channels added for A64 and H6. Standard resolution MMIO timer added
for H616. This timer can be used as a broadcast timer for wakeup from idle
states.
* tag 'sunxi-dt-for-7.1-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: enable h616 timer support
arm64: dts: allwinner: sun50i-h6: add UART DMA channels
arm64: dts: allwinner: sun50i-a64: add UART DMA channels
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Merge tag 'riscv-dt-for-v7.1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V devicetrees for v7.1
Generic:
Add binding coverage for Supm.
Microchip:
Add support for the picgx64 and its curiosity board. This is a PolarFire
SoC without the FPGA.
Add the missing tsu_clk for ptp on the macb on PolarFire SoC and resolve
a long-running problem with gpio interrupts being incorrectly described
on the platform.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v7.1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: microchip: update mpfs gpio interrupts to better match the SoC
riscv: dts: microchip: add tsu clock to macb on mpfs
dt-bindings: riscv: Add Supm extension description
riscv: dts: microchip: remove POLARFIRE mention in Makefile
riscv: dts: microchip: add pic64gx and its curiosity kit
dt-bindings: riscv: microchip: document the PIC64GX curiosity kit
dt-bindings: timer: sifive,clint: add pic64gx compatibility
riscv: dts: microchip: add pinctrl nodes for mpfs/icicle kit
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Merge tag 'imx-dt-7.1' of https://git.kernel.org/pub/scm/linux/kernel/git/frank.li/linux into soc/dt
i.MX ARM device tree changes for 7.1:
- Device Tree Schema Compliance Fixes
Fixed numerous CHECK_DTBS warnings across multiple i.MX SoC families
Renamed nodes to match schema requirements (tcq→touchscreen,
uart8250→serial, iomuxc→pinmux, etc.). Fixed node naming conventions
(added "led-" prefix, proper addressing formats).
Corrected compatible strings and removed undocumented fallbacks. Added
required properties (clocks, clock-names, power supplies,
#sound-dai-cells).
- New Hardware Support
Added DT overlays for various expansion modules (i.MX6 DHCOM PDK2,
PicoITX display boards). Added support for muRata 1YN WiFi chip
(replacement for 1DX) on i.MX6ULL DHCOR board.
i.MX7ULP: Added CPU clock and OPP table support for frequency scaling.
Merge tag 'v7.1-rockchip-dts32-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/dt
Support for the RV1103B SoC and the Onion Omega4 board using it.
While the RV1103B only got a B-extension to its name, the SoC internals
were reworked heavily. So likely it's mainly pin compatible to the
non-B variant.
The dt-binding for the RV1103B clock driver is shared with the clock-
driver branch going into the clock-tree.
* tag 'v7.1-rockchip-dts32-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add Onion Omega4 Evaluation Board
dt-bindings: arm: rockchip: Add Omega4 Evaluation board
ARM: dts: rockchip: Add support for RV1103B
dt-bindings: soc: rockchip: grf: Add RV1103B compatibles
dt-bindings: clock: rockchip: Add RV1103B CRU support
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Merge tag 'v7.1-rockchip-dts32-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/dt
A number of dt-schema cleanups that are log standing, so not suitable
as fix for the current release.
* tag 'v7.1-rockchip-dts32-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Pass linux,code to the power key on rk3288-veyron-pinky
ARM: dts: rockchip: Fix LED node names on rk3288-phycore-rdk
ARM: dts: rockchip: Fix GMAC description n RK3288 boards
ARM: dts: rockchip: Fix RTC description on rk3288-firefly-reload
ARM: dts: rockchip: Add missing the touchscreen interrupt on rk3288-phycore-rdk
ARM: dts: rockchip: Fix the trackpad supply on rk3288-veyron-jerry
ARM: dts: rockchip: Fix the Bluetooth node name on rk3288-veyron
ARM: dts: rockchip: Remove invalid regulator-property from rk3288-veyron
ARM: dts: rockchip: Use mount-matrix on rk3188-bqedison2qc
ARM: dts: rockchip: Fix RTC compatible on rk3288-phycore-rdk
ARM: dts: rockchip: Move PHY reset to ethernet-phy node on rk3036 boards
ARM: dts: rockchip: Remove rockchip,grf from rk3288 tsadc
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The i.MX6SX LCDIF is not fully compatible with the i.MX28 LCDIF. The
i.MX6SX controller provides additional overlay registers (AS_CTRL) which
are not present on i.MX28.
Linux has supported the dedicated compatible string since commit 45d59d704080 ("drm: Add new driver for MXSFB controller").
Other known DT users such as U-Boot and Barebox already support
"fsl,imx6sx-lcdif", so removing the fallback compatible string is low risk
since this device is used for display output only.
Fix the following CHECK_DTB warning:
/arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dtb: lcdif@2220000 (fsl,imx6sx-lcdif): compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6sx-lcdif', 'fsl,imx28-lcdif'] is too long
Frank Li [Wed, 11 Feb 2026 21:41:06 +0000 (16:41 -0500)]
ARM: dts: imx25: rename node name tcq to touchscreen
Rename node name tcq to touchscreen to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx25-karo-tx25.dtb: tscadc@50030000 (fsl,imx25-tsadc): 'tcq@50030400' does not match any of the regexes: '^adc@[0-9a-f]+$', '^pinctrl-[0-9]+$', '^touchscreen@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/mfd/fsl,imx25-tsadc.yaml
Ian Ray [Tue, 17 Feb 2026 13:55:17 +0000 (15:55 +0200)]
ARM: dts: imx: bx50v3: Configure phy-mode to eliminate a warning
Set `phy-mode' on network switch CPU ports to eliminate a warning:
mv88e6085 gpio-0:00: OF node /mdio-gpio/switch@0/ports/port@4 of CPU port 4 lacks the required "phy-mode" property
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com> Signed-off-by: Frank Li <Frank.Li@nxp.com>
Peng Fan [Mon, 2 Mar 2026 15:07:42 +0000 (23:07 +0800)]
ARM: dts: imx7ulp: Add CPU clock and OPP table support
Add missing CPU clock definitions and operating-points-v2 table for the
Cortex-A7 on i.MX7ULP to enable proper CPU frequency scaling and
integration with the cpufreq/OPP frameworks.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com>
Max Merchel [Fri, 20 Feb 2026 14:30:02 +0000 (15:30 +0100)]
ARM: dts: imx6qdl-tqma6: add missing labels
Add the missing labels for the temperature sensor and the EEPROM.
In SoM variants A and B, the components are connected to different
I2C buses. These labels are needed to reference them in subsequent
device trees.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com> Signed-off-by: Frank Li <Frank.Li@nxp.com>
Frank Li [Wed, 21 Jan 2026 18:04:17 +0000 (13:04 -0500)]
ARM: dts: imx: add required clocks and clock-names for ccm
Add required clocks and clock-names for ccm to fix below CHECK_DTBS
warnings:
arch/arm/boot/dts/nxp/imx/imx6dl-alti6p.dtb: clock-controller@20c4000 (fsl,imx6q-ccm): clock-names:0: 'osc' was expected
from schema $id: http://devicetree.org/schemas/clock/imx6q-clock.yaml#
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com>
Frank Li [Thu, 12 Feb 2026 16:19:50 +0000 (11:19 -0500)]
ARM: dts: imx28-tx28: remove undocumented aliases
Remove undocumented aliases, which is not used in kernel to fix
CHECK_DTBS warnings.
arch/arm/boot/dts/nxp/mxs/imx28-tx28.dtb: aliases: 'lcdif_23bit_pins', 'lcdif_24bit_pins', 'reg_can_xcvr', 'spi_gpio', 'spi_mxs' do not match any of the regexes: '^[a-z][a-z0-9\\-]*$', '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/aliases.yaml
Frank Li [Thu, 12 Feb 2026 16:19:49 +0000 (11:19 -0500)]
ARM: dts: imx28-tx28: rename compatible to "edt,edt-ft5206"
The compatible string "edt,edt-ft5x06" is neither documented nor used.
According to drivers/input/touchscreen/edt-ft5x06.c, ft5206, ft5306 and
ft5406 are compatible.
Use "edt,edt-ft5206" instead, as the datasheet does not specify the
exact touchscreen model.
Remove the undocumented fallback compatible string "mr25h256", as the
SPI core strips the vendor prefix.
Fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/mxs/imx28-sps1.dtb: /apb@80000000/apbh-bus@80000000/spi@80014000/flash@0: failed to match any schema with compatible: ['everspin,mr25h256', 'mr25h256']
Frank Li [Thu, 12 Feb 2026 16:19:47 +0000 (11:19 -0500)]
ARM: dts: imx28: rename gpios-reset to reset-gpios of hx8357
Rename gpios-reset to reset-gpios of hx8357 node to fix below CHECK_DTBS
warnings:
arch/arm/boot/dts/nxp/mxs/imx28-cfa10055.dtb: hx8357@0 (himax,hx8357b): Unevaluated properties are not allowed ('gpios-reset' was unexpected)
Frank Li [Thu, 12 Feb 2026 16:19:46 +0000 (11:19 -0500)]
ARM: dts: imx23/28: add "led-" prefix to LED subnodes
Add the "led-" prefix to LED subnodes to fix the below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/mxs/imx23-olinuxino.dtb: leds (gpio-leds): 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml
Frank Li [Thu, 12 Feb 2026 16:19:45 +0000 (11:19 -0500)]
ARM: dts: imx23: fix interrupt names for dma-controller@80024000
There are duplicate "empty" entries in the interrupt-names property of
the DMA controller. Rename them to "empty<n>" to fix below CHECK_DTBS
warnings.
arch/arm/boot/dts/nxp/mxs/imx23-olinuxino.dtb: dma-controller@80024000 (fsl,imx23-dma-apbx): interrupt-names:15: 'empty5' was expected
Frank Li [Wed, 11 Feb 2026 23:12:57 +0000 (18:12 -0500)]
ARM: dts: imx27: remove fsl,imx-osc26m from fixed-clock node
Remove fsl,imx-osc26m from fixed-clock node to fix below CHECK_DTB
warnings:
arch/arm/boot/dts/nxp/imx/imx27-apf27.dtb: osc26m (fsl,imx-osc26m): compatible: ['fsl,imx-osc26m', 'fixed-clock'] is too long
from schema $id: http://devicetree.org/schemas/clock/fixed-clock.yaml
Frank Li [Wed, 11 Feb 2026 23:12:56 +0000 (18:12 -0500)]
ARM: dts: imx27-eukrea-cpuimx27: rename uart8250 to serial
Rename node name uart8250 to serial to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx27-eukrea-mbimxsd27-baseboard.dtb: uart8250@3,200000 (ns8250): $nodename:0: 'uart8250@3,200000' does not match '^serial(@.*)?$'
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com>
Frank Li [Wed, 11 Feb 2026 21:00:03 +0000 (16:00 -0500)]
ARM: dts: imx: remove redundant intermediate node in pinmux hierarchy
Remove the redundant intermediate node between the pinmux and group nodes,
and add the missing "grp" suffix to the group node names.
Fix below CHECK_DTBS warnings:
arm/boot/dts/nxp/imx/imx27-apf27dev.dtb: iomuxc@10015000 (fsl,imx27-iomuxc): Unevaluated properties are not allowed ('imx27-apf27', 'imx27-apf27dev' were unexpected)
from schema $id: http://devicetree.org/schemas/pinctrl/fsl,imx27-iomuxc.yaml
Frank Li [Wed, 11 Feb 2026 21:00:02 +0000 (16:00 -0500)]
ARM: dts: imx: rename iomuxc to pinmux
Rename node name iomuxc to pinmux. Fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx1-apf9328.dtb: iomuxc@21c000 (fsl,imx1-iomuxc): $nodename:0: 'iomuxc@21c000' does not match '^(pinctrl|pinmux)(@[0-9a-f]+)?$'
from schema $id: http://devicetree.org/schemas/pinctrl/fsl,imx27-iomuxc.yaml
Marek Vasut [Mon, 9 Feb 2026 17:07:04 +0000 (18:07 +0100)]
ARM: dts: imx6ull-dhcor: Handle both 1DX and 1YN WiFi on i.MX6ULL DHCOR
The muRata 1DX WiFi/BT chip is mounted on the DHCOM i.MX6ULL. This chip
has been discontinued and replaced by the muRata 1YN chip. The new chip
is a drop-in replacement of the old chip. To support both chips for the
i.MX6ULL DHCOR, drop the more specific compatible string and let the
driver auto-detect the chip type. Currently, there are no known quirks
that would apply only to one or the other chip.
Signed-off-by: Marek Vasut <marex@nabladev.com> Signed-off-by: Frank Li <Frank.Li@nxp.com>
Frank Li [Mon, 2 Feb 2026 19:43:27 +0000 (14:43 -0500)]
ARM: dts: imx7s-warp: Remove data-lanes and clock-lanes for ov2680
The ov2680 only support 1 lane. Needn't additional property to descript it.
Remove it to fix below DTB_CHECK warnings:
camera@36 (ovti,ov2680): port:endpoint: 'clock-lanes', 'data-lanes' do not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/media/i2c/ovti,ov2680.yaml
Frank Li [Mon, 2 Feb 2026 19:43:26 +0000 (14:43 -0500)]
ARM: dts: imx53-smd: Add power supply node for fsl,sgtl5000
Add power supply, #sound-dai-cells and clock nodes for fsl,sgtl5000 to
fix below CHECK_DTB warnings:
arch/arm/boot/dts/nxp/imx/imx53-smd.dtb: sgtl5000@a (fsl,sgtl5000): '#sound-dai-cells' is a required property
from schema $id: http://devicetree.org/schemas/sound/fsl,sgtl5000.yaml#
arch/arm/boot/dts/nxp/imx/imx53-smd.dtb: sgtl5000@a (fsl,sgtl5000): 'clocks' is a required property
from schema $id: http://devicetree.org/schemas/sound/fsl,sgtl5000.yaml#
arch/arm/boot/dts/nxp/imx/imx53-smd.dtb: sgtl5000@a (fsl,sgtl5000): 'VDDA-supply' is a required property
from schema $id: http://devicetree.org/schemas/sound/fsl,sgtl5000.yaml#
arch/arm/boot/dts/nxp/imx/imx53-smd.dtb: sgtl5000@a (fsl,sgtl5000): 'VDDIO-supply' is a required property
Merge tag 'imx-dt64-7.1' of https://git.kernel.org/pub/scm/linux/kernel/git/frank.li/linux into soc/dt
Krzysztof notes:
1. This might impact users of i.MX8MM SPDIF as compatible is being
replaced.
Frank Li writes:
i.MX arm64 device tree changes for 7.1:
- New Board Support
S32N79-RDB, Variscite DART-MX95, DART-MX91 with Sonata carrier boards,
Verdin iMX95 with multiple carrier boards (Yavia, Mallow, Ivy, Dahlia)
TQMa93xx/MBa93xxLA-MINI, SolidRun i.MX8MP HummingBoard IIoT,
SolidRun i.MX8MM SOM and EVB, SolidRun SolidSense-N8 board
Ka-Ro Electronics tx8m-1610 COM, GOcontroll Moduline IV and Moduline Mini,
NXP FRDM-IMX91S board, i.MX93 Wireless EVK board with Wireless SiP,
NXP i.MX8MP audio board v2.
- USB & Type-C Support
Type-C and USB nodes for imx943, correct power-fole for
imx8qxp-mek/imx8qm-mek.
- Audio Enhancements
PDM microphone, bt-sco, and WM8962 sound card support for i.MX952. AONMIX
MQS for i.MX95. Use audio-graph-card2 for imx8dxl-evk. WM8904 audio codec
for imx8mm-var-som.
- Thermal & Cooling
PF09/53 thermal zone, fan node, active cooling on A55, SCMI
sensor/lmm/cpu for imx943/imx94.
- Display Support
Multiple LVDS and parallel display overlays for TQ boards (imx91/imx93).
Parallel display for i.MX93. ontat,kd50g21-40nt-a1 panel for
imx93-9x9-qsb. pixpaper display overlay for i.MX93 FRDM.
- Networking
Multiple queue configuration on eqos for TQMa8MPxL.
MaxLinear PHY support, MCP251xFD CAN controller for imx8mm-var-som.
SDIO WiFi support (imx91-evk, imx8mp-evk, imx943-evk)
- Bluetooth Support
imx943-evk, imx93-14x14-evk, imx95-19x19-evk, imx8mp-evk, imx8mn-evk,
imx8mm-evk.
- Miscellaneous
xspi and MT35XU01G SPI NOR flash for i.MX952.
V2X/ELE mailbox nodes, SCMI misc ctrl-ids for imx94.
eDMA channel reservation for V2X, Cortex M7 support for imx95.
Ethos-U65 NPU and SRAM nodes for imx93.
Wire up DMA IRQ for PCIe for imx8qm-ss-hsio.
- Bug Fixes & Improvements
Complete pinmux for rcwsr12 to fix I2C bus recovery affect other module
pinmux for layscape platform.
Multiple bug fixes for GPIO polarity, IRQ types, pinmux configurations.
GICv3 PPI interrupt CPU mask cleanup across multiple SoCs.
Fixed Ethernet PHY IRQ types on TQ boards.
Fixed UART RTS/CTS muxing issues.
Fixed SD card issues on Kontron boards.
Fixed touch reset configuration.
Removed fallback ethernet-phy-ieee802.3-c22 where appropriate.
Move funnel outside from soc.
TMU sensor ID cleanup.
Change usdhc tuning step for eMMC and SD.
Hexadecimal format, readability improvements, duplicate removal.
* tag 'imx-dt64-7.1' of https://git.kernel.org/pub/scm/linux/kernel/git/frank.li/linux: (139 commits)
arm64: dts: imx8qxp-mek: switch Type-C connector power-role to dual
arm64: dts: imx8qm-mek: switch Type-C connector power-role to dual
arm64: dts: lx2162a-clearfog: set sfp connector leds function and source
arm64: dts: lx2162a-sr-som: add crypto & rtc aliases, model
arm64: dts: lx2160a-cex7: add rtc alias
arm64: dts: lx2160a: complete pinmux for rcwsr12 configuration word
arm64: dts: lx2160a: change zeros to hexadecimal in pinmux nodes
arm64: dts: lx2160a: add sda gpio references for i2c bus recovery
arm64: dts: lx2160a: rename pinmux nodes for readability
arm64: dts: lx2160a: remove duplicate pinmux nodes
arm64: dts: lx2160a: change i2c0 (iic1) pinmux mask to one bit
arm64: dts: lx2160a-cex7/lx2162a-sr-som: fix usd-cd & gpio pinmux
arm64: dts: freescale: imx8mp-moduline-display-106: add typec-power-opmode property
arm64: dts: imx8mp-tqma8mpql: Add DT overlays to explicit list
arm64: dts: imx8mp-evk: Specify ADV7535 register addresses
arm64: dts: imx8dxl-evk: Use audio-graph-card2 for wm8960-2 and wm8960-3
arm64: dts: imx943-evk: Add pf09/53 thermal zone
arm64: dts: imx943-evk: Add fan node and enable active cooling on A55
arm64: dts: imx943-evk: Add nxp,ctrl-ids for scmi_misc
arm64: dts: imx943: Add thermal support
...
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Merge tag 'tegra-for-7.1-arm64-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/dt
arm64: tegra: Device tree changes for v7.1-rc1
Various fixes and new additions across a number of devices. GPIO and PCI
are enabled on Tegra264 and the Jetson AGX Thor Developer Kit, allowing
it to boot via network and mass storage.
* tag 'tegra-for-7.1-arm64-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Add Tegra264 GPIO controllers
arm64: tegra: smaug: Enable SPI-NOR flash
arm64: tegra: Add Jetson AGX Thor Developer Kit support
arm64: tegra: Add PCI controllers on Tegra264
arm64: tegra: Fix RTC aliases
arm64: tegra: Drop redundant clock and reset names for TSEC
arm64: tegra: Fix snps,blen properties
dt-bindings: pci: Document the NVIDIA Tegra264 PCIe controller
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Merge tag 'qcom-arm64-for-7.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
Qualcomm Arm64 DeviceTree updates for v7.1
Introduce the Eliza, Glymur, Mahua, and IPQ5210 Qualcomm SoCs.
Introduce the Redmi 4A, Redmi Go, Arduino Monza (VENTUNO Q), Redmi Note
8T, Purwa EVK, ECS Liva QCS710, additional variants of the DB820c,
Ayaneo Pocket S2, Thundercomm AI Mini PC G1, Samsung Galaxy Core Prime
LTE Verizon Wireless, Wiko Pulp 4G, the Purwa-variant of ASUS Vivobook
S15, the Eliza MTP, and the Glymur and Mahua CRDs.
Introduce UFS support and flatten the DWC3 node on Hamoa. Enable UFS,
SDC, DisplayPort audio playback, and an EL2 overlay for the Hamoa IoT
EVK. Enable DisplayPort audio on the Hamoa CRD and add HDMI support on
the ASUS Zenbook A14. Reduce the duplication of thermal sensors across
Purwa and Hamoa.
Add the QPIC SPI NAND controller on IPQ5332 and IPQ9574. Describe and
enable the eMMC controller on IPQ9574.
Add display, audio/compute remoteprocs, QUP devices, thermal sensors,
display, and CoreSight on the Kaanapali platform. Enable audio, compute
display, PMIC, Bluetooth, and WiFi on the MTP. Describe PMIC, audio and
compute remoteprocs on QRD.
Add role-switching support for the tertiary USB controller on Lemans.
Enable the tertiary USB controller and the GPIO expander on the Lemans
EVK, and add an overlay for the IFP Mezzanine.
Add UFS, camera control interface, audio GPR, and FastRPC support on
Milos. Enable UFS, camera EEPROMs, and hall effect sensor on the
Fairphone FP6.
Add camera control interface and fix a variety of things on the Monaco
platform, add missing FastRPC compute banks. Add eMMC support, describe
the DisplayPort bridge and GPIO expander on the Monaco EVK. Add overlay
for EVK camera and the IFP mezzanine.
Add touchscreen to the Xiaomi Redmi 4A, 5A, and Go, and fix the board-id
on the 4A.
Add the ambient light and proximity sensor on the Asus ZenFone 2
Laser/Selfie.
On Kodiak-based boards, enable the ethernet and USB Type-A ports on the
Rb3Gen2, correct the LT9611 routing on the RubikPi3, add Bluetooth on
the IDP, and add front camera support on the Fairphone FP5.
Introduce an overlay for the Rb3Gen2 Industrial Mezzanine.
Describe DSI on the Monaco SoC and enable Bluetooth, WiFi and DSI/DP
bridge on the Ride board.
Describe the WiFi/BT combo chip properly on the QRB2210 RB1 and QRB4210.
The describe the DSI/DP bringde on the Arduino UnoQ.
Add LLCC on SDM670 and another SPI controller on SDM630.
Properly describe the WiFi/BT chip on a variety of SDM845-based
devices. Introduce the "alert slider" on the OnePlus 6 and OnePlus 6T
devices.
Introduce the PRNG, describe the debug UART, and add the MDSS core reset
on SM6125. Enable the debug UART and fix various issues on the Xiaomi
Redmi Note 8. Describe the touchscreen on the Xiaomi Mi A3.
Properly describe the WiFi/BT combo chip in SM8150 HDK.
Improve the EAS properties on SM8550, in addition to various other
fixes. Introduce a new overlay for the HDK display card.
Introduce various smaller fixes across SM8450 and SM8650.
Add display support on SM8750 and enable DSI and DisplayPort on the MTP.
Also add tsens and thermal-zones.
Add ETR devices, flatten the USB controller node, and mark USB
controllers as wakeup-capable devices, on Talos.
Properly describe the IPA IMEM slice on a variety of platforms.
Drop redundant non-controllable regulator definitions from a variety of
boards.
Drop redundant VSYNC pin state definition from various platforms.
* tag 'qcom-arm64-for-7.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (254 commits)
arm64: dts: qcom: sm8250: Add missing CPU7 3.09GHz OPP
arm64: dts: qcom: sm8550-hdk: add support for the Display Card overlay
arm64: dts: qcom: msm8916-samsung-coreprimeltevzw: add device tree
dt-bindings: qcom: Document samsung,coreprimeltevzw
arm64: dts: qcom: msm8916-samsung-fortuna: Move SM5504 from rossa and refactor MUIC
arm64: dts: qcom: sdm670: add llcc
arm64: dts: qcom: qcm6490-fairphone-fp5: Add front camera support
arm64: dts: qcom: qcm6490-fairphone-fp5: Sort pinctrl nodes by pins
arm64: dts: qcom: milos-fairphone-fp6: Add camera EEPROMs on CCI busses
arm64: dts: qcom: milos: Add CCI busses
arm64: dts: qcom: purwa-iot-evk: Enable UFS
arm64: dts: qcom: eliza: Add thermal sensors
arm64: dts: qcom: sc8280xp: Add dsi nodes on SC8280XP
arm64: dts: qcom: sdm845-oneplus: Describe Wi-Fi/BT properly
arm64: dts: qcom: sdm845-google: Describe Wi-Fi/BT properly
arm64: dts: qcom: drop redundant zap-shader memory-region
arm64: dts: qcom: fix remaining gpu_zap_shader labels
arm64: dts: qcom: msm8996: fix indentation in sdhc2 node
arm64: dts: qcom: monaco-evk: enable UART6 for robot expansion board
arm64: dts: qcom: lemans-evk: enable UART0 for robot expansion board
...
Merge tag 'omap-for-v7.1/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap into soc/arm
ARM: soc/omap updates for v7.1
* tag 'omap-for-v7.1/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap:
ARM: omap2: dead code cleanup in kconfig for ARCH_OMAP4
ARM: OMAP1: Fix DEBUG_LL and earlyprintk on OMAP16XX
ARM: omap: fix all kernel-doc warnings
ARM: omap2: Replace scnprintf with strscpy in omap3_cpuinfo
Merge tag 'v7.1-rockchip-dts64-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/arm
New board, the Khadas Edge 2L. Newly added peripherals are the
OTP nvmem controllers for RK3528, RK3562 and RK3566/8, SPDIF on RK3576.
The RK3566/8 SoCs now also control the Pipe-clocks on their PCIe
controllers and UFSHC controller on RK3576 got an additional reset line.
Apart from that are of course individual board changes and fixes for
older issues that are not specific to the current development cycle.
* tag 'v7.1-rockchip-dts64-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (44 commits)
arm64: dts: rockchip: configure hdmirx in Rock 5 ITX
arm64: dts: rockchip: assign pipe clock to rk356x PCIe lanes
arm64: dts: rockchip: Add mphy reset to ufshc node
arm64: dts: rockchip: Enable OTP controller for RK3528
arm64: dts: rockchip: Enable OTP controller for RK356x
arm64: dts: rockchip: Enable OTP controller for RK3562
arm64: dts: rockchip: Enable PCIe CLKREQ# for RK3588 on Rock 5b-5bp-5t series
arm64: dts: rockchip: add SD/eMMC aliases for ArmSom Sige5
arm64: dts: rockchip: Add SPDIF nodes to RK3576 device tree
arm64: dts: rockchip: Add Khadas Edge 2L board
dt-bindings: arm: rockchip: Add Khadas Edge 2L board
arm64: dts: rockchip: Fix RK3562 EVB2 model name
arm64: dts: rockchip: Correct Joystick Axes on Gameforce Ace
arm64: dts: rockchip: Correct Fan Supply for Gameforce Ace
Revert "arm64: dts: rockchip: add SPDIF audio to Beelink A1"
arm64: dts: rockchip: Fix Bluetooth stability on LCKFB TaiShan Pi
arm64: dts: rockchip: enable vicap dvp on wolfvision pf5 io expander
arm64: dts: rockchip: Add analog audio switches to RK3576 EVB1
arm64: dts: rockchip: Enable GPU on rk3566-pinenote
arm64: dts: rockchip: Make Jaguar PCIe-refclk pin use pull-up config
...
Merge tag 'ti-k3-dt-for-v7.1' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into soc/arm
TI K3 device tree updates for v7.1
Generic Fixes/Cleanups:
- k3-pinctrl: Cleanup alignment and reorder macros
- ti,min-output-impedance addition to all K3 board DT files
SoC Specific Features and Fixes:
AM62L:
- Add RNG node
- Support cpufreq scaling
J721S2:
- Make MAIN domain system control bus a simple-bus
- Add second DSI node
J722S:
- Add main_i2c4 device node
J7200:
- Make MAIN domain system control bus a simple-bus
Board Specific Features and Fixes:
AM642 EVM:
- Add ICSSG0 overlay for dual EMAC support
AM62:
- LP-SK: Enable internal pulls for MMC0 data pins
- SK: Enable Main UART wakeup
- phycore-som: Add 128MiB of global CMA
- Verdin: Add Zinnia board support and misc cleanup
AM62A7-SK:
- Enable Main UART wakeup
- Fix pin name in comment from M19 to N22
AM62D2 EVM:
- Enable Main UART wakeup and set wakeup-source system-states
AM62L3 EVM:
- Disable MMC1 internal pulls on data pins
- Enable Main UART wakeup and enable wkup_uart0 pins/target node
AM62P:
- SK: Disable MMC1 internal pulls on data pins and enable Main UART
wakeup
- Verdin: Add Zinnia support and misc cleanup
spear13xx.dtsi defines a thermal_flags property in spear thermal sensor
node which is both unused in kernel and undocumented in spear thermal
sensor's binding.
There were no dtbs_check warnings associated with this property as the
underlying spear thermal binding was not converted to DTSchema.
Most likely st,thermal-flags is a misspelling of thermal_flags in
spear13xx.dtsi. Since both st/spear1310.dtsi and st/spear1340.dtsi
define st,thermal-flags property in spear thermal sensor node, we can
safely remove this property from spear13xx.dtsi.
arm64: dts: qcom: Add the Lenovo IdeaCentre Mini X
The Lenovo IdeaCentre Mini X (Snapdragon) Desktop is a Hamoa-based
ultracompact desktop PC. It provides HDMI, DisplayPort, USB Type-C
display outputs, 5 additional USB ports, Ethernet, dual NVME slots,
headphone jack, WiFi, and Bluetooth.
dt-bindings: arm: qcom: Document the Lenovo IdeaCentre Mini X
The Lenovo IdeaCentre Mini X (Snapdragon) Desktop is a Hamoa-based
ultracompact desktop PC. It provides HDMI, DisplayPort, USB Type-C
display outputs, 5 additional USB ports, Ethernet, dual NVME slots,
headphone jack, WiFi, and Bluetooth.
The Talos EVK board does not include a camera sensor
by default. This DTSO has enabled the Arducam 12.3MP
IMX577 Mini Camera Module on the CSI-1 interface.
CSI-1 interface using mclk2 as the MCLK source on this board.
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Signed-off-by: Wenmeng Liu <wenmeng.liu@oss.qualcomm.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20260305-sm6150_evk-v6-5-38ce4360d5e0@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Mukesh Ojha [Tue, 27 Jan 2026 11:43:50 +0000 (17:13 +0530)]
arm64: dts: qcom: talos: Add EL2 overlay
All the existing variants Talos boards are using Gunyah hypervisor
which means that, so far, Linux-based OS could only boot in EL1 on
those devices. However, it is possible for us to boot Linux at EL2
on these devices [1].
When running under Gunyah, the remote processor firmware IOMMU streams
are controlled by Gunyah. However, without Gunyah, the IOMMU is managed
by the consumer of this DeviceTree. Therefore, describe the firmware
streams for each remote processor.
Add a EL2-specific DT overlay and apply it to Talos IOT variant
devices to create -el2.dtb for each of them alongside "normal" dtb.
Sudarshan Shetty [Tue, 31 Mar 2026 06:01:07 +0000 (11:31 +0530)]
arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board
Add the device tree for the QCS615-based Talos EVK platform. The
platform is composed of a System-on-Module following the SMARC
standard, and a Carrier Board.
The Carrier Board supports several display configurations, HDMI and
LVDS. Both configurations use the same base hardware, with the display
selection controlled by a DIP switch.
Use a DTBO file, talos-evk-lvds-auo,g133han01.dtso, which defines an
overlay that disables HDMI and adds LVDS. The DTs file talos-evk
can describe the HDMI display configurations.
According to the hardware design and vendor guidance, the WiFi PA
supplies VDD_PA_A and VDD_PA_B only need to be enabled at the same time
as asserting WLAN_EN.
On this platform, WiFi enablement is controlled via the WLAN_EN GPIO
(GPIO84), which also drives the VDD_PA_A and VDD_PA_B power enables.
Remove the VDD_PA_A and VDD_PA_B regulator nodes from the device tree
and rely on WLAN_EN to enable WiFi functionality.
Add talos-evk-usb1-peripheral.dtso overlay to enable USB0 peripheral
(EDL) mode. The base DTS will keep USB0 host-only due to hardware
routing through the EDL DIP switch, and the overlay switches the
configuration for device-mode operation.
The LVDS backlight hardware has been updated to use a simplified
design. The backlight enable signal is now permanently pulled up
to 3.3V and is no longer controlled via GPIO59.
Remove the GPIO59 based backlight configuration from the device
tree, as it is no longer routed to the LVDS interface.
The initial device tree includes support for:
- CPU and memory
- UART
- GPIOs
- Regulators
- PMIC
- Early console
- AT24MAC602 EEPROM
- MCP2515 SPI to CAN
- ADV7535 DSI-to-HDMI bridge
- DisplayPort interface
- SN65DSI84ZXHR DSI-to-LVDS bridge
- Wi-Fi/BT
Sudarshan Shetty [Tue, 31 Mar 2026 06:01:06 +0000 (11:31 +0530)]
arm64: dts: qcom: talos/qcs615-ride: Fix inconsistent USB PHY node naming
The USB PHY nodes has inconsistent labels as 'usb_1_hsphy'
and 'usb_hsphy_2' across talos.dtsi and qcs615-ride.dts.
This patch renames them to follow a consistent naming
scheme.
Merge tag 'qcom-arm32-for-7.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
Qualcomm Arm32 DeviceTree updates for v7.1
Qualcomm APQ8084 is incomplete and hasn't seen functional contributions
since 2016, so drop the platform (for now?). Also drop a number of
unused IPQ-related dtsi files.
Lastly clean up the RPM bus clocks in MSM8974 interconnect nodes.
* tag 'qcom-arm32-for-7.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: msm8974: Drop RPM bus clocks
ARM: dts: qcom: drop apq8084 support
ARM: dts: qcom: Drop unused .dtsi
Merge tag 'thead-dt-for-v7.1-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/fustini/linux into soc/dt
T-HEAD Devicetrees for 7.1, part 2
Additional updates to T-Head device trees for v7.1:
- Enable the display pipeline for the TH1520-based BeagleV Ahead board
by adding the HDMI connector node, connecting it to the HDMI
controller, and activating the DPU and HDMI nodes.
- Add coefficients to the TH1520 PVT node as the values in the TH1520
manual differ from the defaults in the driver.
* tag 'thead-dt-for-v7.1-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/fustini/linux:
riscv: dts: thead: beaglev-ahead: enable HDMI output
riscv: dts: thead: th1520: add coefficients to the PVT node
Merge tag 'renesas-dts-for-v7.1-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
Renesas DTS updates for v7.1 (take two)
- Add DT overlay support for the MayQueen PixPaper display on the
Yuridenki-Shokai Kakip board,
- Add Ethernet PHY interrupt support for the RZ/T2H and RZ/N2H EVK
boards,
- Add SPI and PCIe support for the RZ/G3E SoC and the RZ/G3E SMARC EVK
board,
- Add DT overlay support for the WaveShare 13.3" 1920x1080 DSI
Capacitive Touch Display and the Olimex MIPI-HDMI adapter on the
Retronix Sparrow Hawk board,
- Drop several superfluous C22 Ethernet PHY compatible strings,
- Remove WDT nodes meant for other CPU cores on the RZ/V2N SoC,
- Remove unavailable LVDS panel support for the Beacon ReneSoM base
board,
- Add initial support for the RZ/G3L (R9A08G046) SoC, and the RZ/G3L
SMARC SoM and EVK boards,
- Add Versa3 clock generator support for the RZ/V2H EVK development
board,
- Miscellaneous fixes and improvements.
Merge tag 'stm32-dt-for-7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/dt
STM32 DT for v7.1, round 1
Highlights:
----------
- MPU:
- STM32MP13:
- Introduce and enable debug bus on DK board.
- Enable Coresight on DK board.
- Add DT overlays for DH board.
- Add Wakeup capabilities on I2C nodes.
- STMP32MP15:
- ST:
- Enable DCMI DMA chaining to improve performances.
- Introduce and enable debug bus on EV and DK board.
- Enable Coresight on EV and DK board.
- DH:
- Add DT overlays for DH board.
- Phytec:
- Rename "Phycore" to "phyboard-sargas" DT files and introduce
SOM device tree file.
- Fix and enhance current support.
- STM32MP21:
- Add Bsec support.
- STM32MP23:
- Add LTDC and LVDS support and enable display on STM32MP235F-DK
board.
- STM32MP25:
- Enable display on STM32MP235F-DK board.
* tag 'stm32-dt-for-7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (42 commits)
arm64: defconfig: Enable STMicroelectronics STM32 display support
arm64: dts: st: enable display support on stm32mp257f-dk board
arm64: dts: st: describe power supplies for stm32mp257f-dk board
arm64: dts: st: enable display support on stm32mp235f-dk board
arm64: dts: st: describe power supplies for stm32mp235f-dk board
arm64: dts: st: add clock-cells to syscfg node on stm32mp231
arm64: dts: st: add lvds support on stm32mp235
arm64: dts: st: add ltdc support on stm32mp235
arm64: dts: st: add ltdc support on stm32mp231
arm64: dts: st: omit unused pinctrl groups from stm32mp25 dtb files
arm64: dts: st: add bootph-all in bsec node to stm32mp215f-dk
arm64: dts: st: add bsec support to stm32mp21
ARM: dts: stm32: fix misalignments in nodes of stm32mp131
ARM: dts: stm32: fix misalignments in nodes of stm32mp151
arm64: dts: st: describe i2c2 / i2c8 on stm32mp235f-dk
arm64: dts: st: describe i2c2 / i2c8 on stm32mp257f-dk
arm64: dts: st: disable DMA usage for i2c on stm32mp257f-ev1
arm64: dts: st: add i2c2 pinmux nodes in stm32mp25-pinctrl.dtsi
arm64: dts: st: update i2c nodes interrupt/wakeup-source in stm32mp231
arm64: dts: st: update i2c nodes interrupt/wakeup-source in stm32mp251
...
Merge tag 'samsung-dt64-7.1' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/dt
Samsung DTS ARM64 changes for v7.1
1. Add initial support for Axis ARTPEC-9 SoC and Alfred board using it.
Just like ARTPEC-8, this is a derivative of Samsung Exynos SoC made
for Axis, sharing most or all of core SoC blocks with Samsung
designs.
2. New boards: Exynos7870 based Samsung Galaxy J7 (2016) and Samsung
Galaxy J5 (2017).
3. Google GS101 Pixel phone: describe all PMIC regulators and Maxim
fuel-gauge.
Merge tag 'arm-soc/for-7.1/devicetree-arm64' of https://github.com/Broadcom/stblinux into soc/dt
This pull request contains Broadcom ARM64-based SoCs Device Tree updates
for 7.1, please pull the following:
- Maira adds the V3D DT node to the 2712 (Raspberry Pi 5) SoC
- Gergor adds the I2C controller, CSI (camera), ISP (image signal
processor), fixes the pinctrl node and updates the UART10 interrupt
for the RP1 sister chip to the 2712 (Raspberry Pi 5)
- Rob moves the firmware and GPU to the root level to fix DTC warnings
Paul Sajna [Wed, 1 Apr 2026 03:15:11 +0000 (20:15 -0700)]
arm64: dts: qcom: sdm845-lg: Add uarts and Bluetooth
uart9 is debug serial on USB SBU1/2
UART RX is SBU1 and UART TX is SBU2 of the USB-C port).
1.8V Logic Level
Tested using pololu usb07a https://www.pololu.com/product/2585
and CH340 USB-UART
uart6 is bluetooth
Bluetooth: hci0: setting up wcn399x
Bluetooth: hci0: QCA Product ID :0x0000000a
Bluetooth: hci0: QCA SOC Version :0x40010214
Bluetooth: hci0: QCA ROM Version :0x00000201
Bluetooth: hci0: QCA Patch Version:0x00000001
Bluetooth: hci0: QCA controller version 0x02140201
Bluetooth: hci0: QCA Downloading qca/crbtfw21.tlv
Bluetooth: hci0: QCA Downloading qca/judyln/crnv21.bin
Bluetooth: hci0: QCA setup on UART is completed
Add paths for Qualcomm firmware, including:
ipa, modem, venus, gpu
GPU and bluetooth are confirmed working, others may need more
testing/fixes
But regardless they will need the firmware paths specified here
and firmware added upstream before they will work, so might as well
get started on it now.
Abel Vesa [Mon, 30 Mar 2026 14:24:08 +0000 (17:24 +0300)]
arm64: dts: qcom: glymur-crd: Enable DisplayPort support
The two Type-C ports found on Glymur CRD are DisplayPort alternate mode
capable. Everything is in place already for the USB, but for DisplayPort
the controllers need to be enabled.
So enable the related DisplayPort controller for each of these two
ports. Also define the supported link frequencies for each output.
Merge tag 'arm-soc/for-7.1/devicetree' of https://github.com/Broadcom/stblinux into soc/dt
This pull request contains Broadcom ARM-based SoCs Device Tree updates
for 7.1, please pull the following:
- Rafal provides a complete description of the PCIe Root Complex nodes
in order to silence a number of dtc warnings
- Rosen provides the necessary NVMEM properties to allow describing the
WAN device MAC address from NVRAM, also adds better LEDs, USB GPIOs
and Wi-Fi buttons for the Linksys EA9200 router
- Linus completes the BCA devices description by adding the I2C block
and fixing interrupts for the DMA block on 63138 and 6878
* tag 'arm-soc/for-7.1/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: EA9200: specify partitions
ARM: dts: BCM5301X: EA9200: add LEDs
ARM: dts: BCM5301X: EA9200: add USB GPIOs
ARM: dts: BCM5301X: EA9200: add WiFi button
ARM: dts: broadcom: bcm2835-rpi: Move non simple-bus nodes to root level
ARM: dts: bcm63148: Add I2C block
ARM: dts: bcm63138: Add I2C block
ARM: dts: bcm6878: Add I2C bus block
ARM: dts: bcm6855: Add I2C bus blocks
ARM: dts: bcm6846: Add I2C bus block
ARM: dts: bcm63138: Fix DMA IRQ
ARM: dts: bcm6878: Fix PL081 DMA block IRQ
ARM: dts: BCM5301X: AC5300: set WAN MAC from nvram
ARM: dts: BCM5301X: AC3100: set WAN MAC from nvram
ARM: dts: BCM5301X: panamera: set WAN MAC from nvram
ARM: dts: BCM5301X: EA9200: set WAN MAC from nvram
ARM: dts: BCM5301X: add root pcie bridges
ARM: dts: BCM5301X: Drop extra NAND controller compatible
ARM: dts: BCM5301X: Describe PCIe controllers fully
Merge tag 'nuvoton-arm64-7.1-devicetree-0' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/bmc/linux into soc/dt
nuvoton: first batch of arm64 devicetree changes for v7.1
Just the one change this time, dropping syscon properties where they weren't
defined.
* tag 'nuvoton-arm64-7.1-devicetree-0' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/bmc/linux:
arm64: dts: nuvoton: drop unused syscon property from watchdog node
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
ARM: dts: am335x: Add Seeed Studio BeagleBone HDMI cape overlay
Add devicetree overlay for the Seeed Studio BeagleBone HDMI cape, which
provides HDMI output via an ITE IT66121 HDMI bridge and audio support
through McASP.
The cape is designed for BeagleBone Green but is also compatible with
BeagleBone and BeagleBone Black due to pin compatibility.
projects / thirdparty / kernel / linux.git / log
