tests: ap_open_out_of_memory to skip i802_init test if needed
The eloop_register_read_sock() call in i802_init() will be skipped if
the driver supports control port for EAPOL RX, so need to skip this part
of the test case conditionally.
Do not open l2_packet bridge workaround socket if control port is used
This allows wpa_supplicant to avoid the packet socket workaround for
cases where a bridge interface is used if the driver supports control
port for EAPOL frame TX and RX.
nl80211: Disable EAPOL TX over control port in AP mode by default
Since this nl80211 mechanism for sending EAPOL frames does not currently
support TX status notification, disable it by default of AP mode where
the Authenticator state machine uses those notifications to optimize
retransmission. The control port TX can be enabled for AP mode with
driver param control_port_ap=1.
Markus Theil [Sat, 11 Apr 2020 10:25:22 +0000 (12:25 +0200)]
nl80211: Use nl80211 control port for receiving EAPOL frames
Use and/or set socker owner where necessary to allow EAPOL frames to be
received using the nl80211 control port. This is done when the driver
indicates support for the control port without previous hardcoded
reception of RSN preauth frames.
Use methods which set or use the connection owner nl_sock * where
necessary. Initial operations need to register with the SOCKET_OWNER
attribute set (e.g., connect for STA mode). Final operations need to use
the socket which holds the owner attribute (e.g., disconnect for STA
mode).
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Markus Theil [Sat, 11 Apr 2020 10:25:18 +0000 (12:25 +0200)]
nl80211: Check ethertype for control port RX
nl80211 control port event handling previously did not differentiate
between EAPOL and RSN preauth ethertypes. Add checking of the ethertype
and report unexpected frames (only EAPOL frames are supposed to be
delivered through this path).
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
nl80211: Add a separate driver capability for control port RX
This is needed since the initial implementation of the control port
mechanism in the kernel mixed in RSN pre-authentication ethertype
unconditionally (and IMHO, incorrectly) into the control port.
WPS: Convert WPA/TKIP-only to WPA+WPA2 mixed mode credential
This case of accepting WPA/TKIP-only credential based on internal
registrar request to configure an AP to use TKIP was still remaining
while all the WPS cases were supposed to enable mixed mode
automatically. This is bit of a corner case since this is based on
explicit local request to configure TKIP, but anyway, convert this one
as well to allow WPA2/CCMP to be used.
Disha Das [Thu, 9 Apr 2020 04:12:21 +0000 (09:42 +0530)]
Allow TKIP support to be removed from build
Add a build flag CONFIG_NO_TKIP=y to remove all TKIP functionality from
hostapd and wpa_supplicant builds. This disables use of TKIP as both the
pairwise and group cipher. The end result does not interoperate with a
WPA(v1)-only device or WPA+WPA2 mixed modes.
FT: Testing override for RSNXE Used subfield in FTE (AP)
Allow hostapd to be requested to override the RSNXE Used subfield in FT
reassociation case for testing purposes with "ft_rsnxe_used=<0/1/2>"
where 0 = no override, 1 = override to 1, and 2 = override to 0.
FT: Testing override for RSNXE Used subfield in FTE
Allow wpa_supplicant to be requested to override the RSNXE Used subfield
in FT reassociation case for testing purposes with "SET ft_rsnxe_used
<0/1/2>" where 0 = no override, 1 = override to 1, and 2 = override to
0.
FT: Discard ReassocReq with mismatching RSNXE Used value
Discard the FT Reassociation Request frame instead of rejecting it
(i.e., do not send Reassociation Response frame) if RSNXE Used is
indicated in FTE, but no RSNXE is included even though the AP is
advertising RSNXE.
While there is not really much of a difference between discarding and
rejecting the frame, this discarding behavior is what the standard says
for this type of an error case.
The ar operations with embedded libraries were not exactly portable
or strictly speaking necessary. Drop that library completely to make
this more portable.
FT RRB: Remove confusing debug print about extra data
The "FT: Ignore extra data in end" hexdump is quite confusing since it
shows all the IEs that were actually either processed or forwarded.
There is no code path that could reach this debug print with actual real
extra data. Remove it and the dead increment of pos to avoid warnings
from static analyzers.
FT: Remove and re-add STA entry after FT protocol success with PMF
Allow STA entry to be removed and re-added to the driver with PMF is
used with FT. Previously, this case resulted in cfg80211 rejecting STA
entry update after successful FT protocol use if the association had not
been dropped and it could not be dropped for the PMF case in
handle_auth().
Thomas Pedersen [Tue, 31 Mar 2020 18:09:00 +0000 (11:09 -0700)]
tests: Enable MACsec testing by default in the VM kernel
Include support for MACsec testing in the (vm) kernel by default.
Don't include support in the example hostapd or wpa_supplicant configs
yet since that would potentially break the build on older distributions
like Ubuntu 16.04, which is supported until April 2021.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
wlantest: Remove duplicate PN/RSC prints from replay cases
The PN and RSC are already printed in the "replay detected" debug
message so there is no point in having separate hexdumps of the same
values immediately after that.
DPP: Mandate mutual auth with NFC negotiated connection handover
Mark own bootstrap information as having been used in NFC negotiated
connection handover and do not accept non-mutual authentication when
processing Authentication Response from the peer when such bootstrapping
information is used.
OWE: Remove check for unexpected DH Parameter IE use with other AKMs
While the Diffie-Hellman Parameter element is defined in RFC 8110
explicitly for use witht he OWE AKM, it has now been proposed to be used
with another AKM (DPP). Should any other AKM be extended in similar
manner in the future, the check against unexpected use could result in
additional interoperability issues. Remove that and instead, ignore the
unexpected Diffie-Hellman Parameter element if it is included in
(Re)Association Request frame when any other AKM is negotiated.
DPP2: Add Connector and C-sign-key in psk/sae credentials for reconfig
If the Enrollee indicates support for DPP R2 or newer, add Connector and
C-sign-key in psk/sae credentials (i.e., cases where DPP AKM is not
enabled) for reconfiguration. Extend processing of such credentials in
wpa_supplicant network profile addition to handle this new case
correctly by not setting key_mgmt=DPP based on Connector being present,
but by looking at the actual akm value in the config object.
wlantest: Update PTK after rekeying even if EAPOL-Key msg 4/4 is missing
Update TPTK to PTK if a valid EAPOL-Key msg 2/4 and 3/4 are available,
but 4/4 is missing. This avoids certain cases where the new TK could be
derived, but it was not being used to try to decrypt following encrypted
frames.
wlantest: Do not report decryption keys when checking only zero TK
All the "Failed to decrypt frame" debug prints were confusing since
those were not supposed to be shown unless there were one or more real
TKs available. The recently added check for zero TK added these notes
for that case which is not really correct, so get rid of them.
DPP2: Clear requirement for QR Code mutual authentication for chirping
The chirping cases are not really targeting interactive operations, so
clear the requirement for mutual authentication when DPP_CHIRP command
is used. This avoids testing isues where an earlier DPP_LISTEN command
has used qr=mutual parameter and that seting not getting cleared before
the next DPP_CHIRP command is used.
This fixes a test case failure in the following test sequence:
dpp_auth_resp_status_failure dpp_controller_relay_chirp
Beacon frame protection event for incorrect protection
Define a driver interface event for Beacon frame protection failures.
Report such events over the control interface and send a
WNM-Notification Request frame to the AP as well.
P Praneesh [Mon, 9 Mar 2020 10:53:50 +0000 (16:23 +0530)]
wpa_supplicant: Add HE override support
Add HE override support under the build parameter CONFIG_HE_OVERRIDES=y.
The disable_he=1 network profile parameter can be used to disable HE.
This requires a fallback to VHT on the 5 GHz band and to HT on the 2.4
GHz band.
There is no nl80211 support for configuring the driver to disable HE, so
for now, this applies only to IBSS and mesh cases.
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Sriram R [Thu, 26 Mar 2020 03:12:19 +0000 (08:42 +0530)]
hostapd: Validate the country_code parameter value
cfg80211/regulatory supports only ISO 3166-1 alpha2 country code and
that's what this parameter is supposed to use, so validate the country
code input before accepting the value. Only characters A..Z are
accepted.
In repeater mode remote AP may request channel switch to a new channel.
Check if DFS is required for the new channel before proceeding with
normal AP operations. Start CAC procedure if radar detection is required
and channel is not yet marked as available.
hostapd: Add support for DFS channels in CHAN_SWITCH
Enable support for DFS channels in the CHAN_SWITCH command. Perform CAC
instead of CSA if DFS channel is selected. Then restart normal AP
operations.
Note that the current implementation provides a simplified approach. It
does not check if the selected DFS channel block is already in the
HOSTAPD_CHAN_DFS_AVAILABLE state. CAC procedure is restarted anyway.
Add a new hostapd_is_dfs_overlap() helper function to DFS module. This
function tells whether the selected frequency range overlaps with DFS
channels in the current hostapd configuration. Selected frequency reange
is specified by its center frequency and bandwidth.
DFS: Rename and export hostapd_config_dfs_chan_available helper
Rename DFS helper hostapd_config_dfs_chan_available() to
hostapd_is_dfs_chan_available(). Enable access to this helper function
from other hostapd components.
hostapd: Basic channel check for CHAN_SWITCH parameters
Implement channel sanity check for the CHAN_SWITCH command. Verify
provided values for bandwidth, frequencies, and secondary channel
offset. Reject requested channel switch operation if basic constraints
on frequencies and bandwidth are not fulfilled.
Thomas Pedersen [Fri, 27 Mar 2020 22:51:44 +0000 (15:51 -0700)]
tests: Convert kernel-config to defconfig
Make the included kernel-config a little more minimal by checking in the
defconfig instead.
Generate the defconfig by checking out a linux at tag wt-2020-03-17,
copy kernel-config to .config, run
'yes "" | make oldconfig && make savedefconfig',
and copy resulting defconfig to kernel-config.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Jouni Malinen [Sat, 28 Mar 2020 18:39:19 +0000 (20:39 +0200)]
Add a hostapd testing option for skipping association pruning
The new skip_prune_assoc=1 parameter can be used to configure hostapd
not to prune associations from other BSSs operated by the same process
when a station associates with another BSS. This can be helpful in
testing roaming cases where association and authorization state is
maintained in an AP when the stations returns.
Jouni Malinen [Sat, 28 Mar 2020 18:38:11 +0000 (20:38 +0200)]
nl80211: Allow full AP client state capability to be disabled
The new driver param full_ap_client_state=0 can be used to test
functionality with the driver capability for full AP client state being
forced to be disabled.
projects / thirdparty / hostap.git / log
