IR receiver using nuvoton-cir and lirc required additional configuration
steps after upgrade from kernel 3.16 to 3.17-rcX. Bisected regression to
commit da6e162d6a4607362f8478c715c797d84d449f8b ("[media] rc-core:
simplify sysfs code").
The regression comes from adding function change_protocol in ir-raw.c.
It changes behaviour so that only the protocol enabled by driver's
map_name will be active after registration. This breaks user space
behaviour, lirc does not get key press signals anymore.
Enable lirc protocol by default for ir raw decoders to restore original
behaviour.
Signed-off-by: Tomas Melin <tomas.melin@iki.fi> Acked-by: David Härdeman <david@hardeman.nu> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tevii S480 outputs 18V on startup for the LNB supply voltage and does not
automatically power down. This blocks other receivers connected
to a satellite channel router (EN50494), since the receivers can not send the
required DiSEqC sequences when the Tevii card is connected to a the same SCR.
This patch switches off the LNB supply voltage on initialization of the frontend.
[mchehab@osg.samsung.com: add a comment about why we're explicitly
turning off voltage at device init] Signed-off-by: Ulrich Eckhardt <uli@uli-eckhardt.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With kernel 3.17 the imon remote control for device 15c2:0034 does not
work anymore, which uses the OTHER protocol. Only the front panel
buttons which uses the RC6 protocol are working.
When a new video frame is started, the driver takes the next video buffer from
the list of active buffers and moves it to dev->usb_ctl.vid_buf / dev->usb_ctl.vbi_buf
for further processing.
On streaming stop we currently only give back the pending buffers from the list
but not the ones which are currently processed.
This causes the following warning from the vb2 core since kernel 3.15:
Maximum satellite symbol rate used is 45000000Sps which overflows
when multiplied by 135. As final calculation result is fraction,
we could use mult_frac macro in order to keep calculation inside
32 bit number limits and prevent overflow.
Original bug and fix was provided by Nibble Max. I decided to
implement it differently as it is now.
Reported-by: Nibble Max <nibble.max@gmail.com> Tested-by: Nibble Max <nibble.max@gmail.com> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[media] em28xx: check if a device has audio earlier
Better to split chipset detection from the audio setup. So, move the
detection code to em28xx_init_dev().
It broke analog audio of the Hauppauge winTV HVR 900 and very likely many other
em28xx devices.
Background:
The local variable has_audio in em28xx_usb_probe() describes if the currently
probed _usb_interface_ has an audio endpoint, while dev->audio_mode.has_audio
means that the _device_ as a whole provides analog audio.
Hence it is wrong to set dev->audio_mode.has_audio = has_audio in em28xx_usb_probe().
As result, audio support is no longer detected and configured on devices which
have the audio endpoint on a separate interface, because em28xx_audio_setup()
bails out immediately at the beginning.
Revert the faulty commit to restore the old audio detection procedure, which checks
the chip configuration register to determine if the device has analog audio.
Fix clamp_align() used in v4l_bound_align_image() to prevent overflow
when passed large value like UINT32_MAX.
In the current implementation:
clamp_align(UINT32_MAX, 8, 8192, 3)
returns 8, because in line:
x = (x + (1 << (align - 1))) & mask;
x overflows to (-1 + 4) & 0x7 = 3, while expected value is 8192.
v4l_bound_align_image() is heavily used in VIDIOC_S_FMT and
VIDIOC_SUBDEV_S_FMT ioctls handlers, and documentation of the latter
explicitly states that:
"The modified format should be as close as possible to the original
request."
-- http://linuxtv.org/downloads/v4l-dvb-apis/vidioc-subdev-g-fmt.html
Thus one would expect, that passing UINT32_MAX as format width and
height will result in setting maximum possible resolution for the
device. Particularly, when the driver doesn't support
VIDIOC_ENUM_FRAMESIZES ioctl, which is common in the codebase.
The current error path calls tilcdc_unload() in case of an error to release
the resources. However, this is wrong because not all resources have been
allocated by the time an error occurs in tilcdc_load().
To fix it, this commit adds proper labels to bail out at the different
stages in the load function, and release only the resources actually allocated.
Tested-by: Darren Etheridge <detheridge@ti.com> Tested-by: Johannes Pointner <johannes.pointner@br-automation.com> Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Dave Airlie <airlied@redhat.com> Fixes: 3a49012224ca ("drm/tilcdc: panel: fix leak when unloading the module") Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The userspace drm.h include doesn't prefix the drm directory. This can lead
to compile failures as /usr/include/drm/ isn't in the standard gcc include
paths. Fix it to be <drm/drm.h>, which matches the rest of the driver drm
header files that get installed into /usr/include/drm.
Red Hat Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1138759
sg_alloc_table_from_pages() can build us a table with coalesced ranges which
means we need to iterate over pages and not sg table entries when releasing
page references.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: "Barbalho, Rafael" <rafael.barbalho@intel.com> Tested-by: Rafael Barbalho <rafael.barbalho@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Remove unused local variable sg.] Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we fail to create our mmu notification, we report the error back and
currently store the error inside the i915_mm_struct. This not only causes
subsequent registerations of the same mm to fail (an issue if the first
was interrupted by a signal and needed to be restarted) but also causes
us to eventually try and free the error pointer.
nv92 hardware has only 16 interrupt lines, while nv94 and later
has 32. Accessing 0xe0c{0,4} registers on nv92 can lead to incorrect
PDISP setup. This is a regression introduced with
The translation from the X driver to the KMS one typo'ed a couple
of array indices, causing the HW cursor to look weird (blocky with
leaking edge colors). This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit which introduced TransducerSerialNumber (368c966) is missing
two crucial implementation details. Firstly, the commit does not set the
type/code/bit/max fields as expected later down the code which can cause
the driver to crash when a tablet with this usage is connected. Secondly,
the call to 'set_bit' causes MSC_PULSELED to be sent instead of the
expected MSC_SERIAL. This commit addreses both issues.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Reviewed-by: Ping Cheng <pingc@wacom.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the change to struct input_mt_pos some variables are now bitfields
instead of integers. Automatic conversion from integer to bitfield entry
destroys information, therefore enforce boolean interpretation instead.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1114768 Fixes: 02d04254a5df ("Input: alps - use struct input_mt_pos to track coordinates") Signed-off-by: Andreas Bosch <linux@progandy.de> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The framebuffer code uses the current background color to fill the border
when switching consoles, however, this results in inconsistent behavior.
For example:
- start Midnigh Commander
- the border is black
- switch to another console and switch back
- the border is cyan
- type something into the command line in mc
- the border is cyan
- switch to another console and switch back
- the border is black
- press F9 to go to menu
- the border is black
- switch to another console and switch back
- the border is dark blue
When switching to a console with Midnight Commander, the border is random
color that was left selected by the slang subsystem.
This patch fixes this inconsistency by always using black as the
background color when switching consoles.
The function bitcpy_rev has a bug that may result in screen corruption.
The bug happens under these conditions:
* the end of the destination area of a copy operation is aligned on a long
word boundary
* the end of the source area is not aligned on a long word boundary
* we are copying more than one long word
In this case, the variable shift is non-zero and the variable first is
zero. The statements FB_WRITEL(comp(d0, FB_READL(dst), first), dst) reads
the last long word of the destination and writes it back unchanged
(because first is zero). Correctly, we should write the variable d0 to the
last word of the destination in this case.
This patch fixes the bug by introducing and extra test if first is zero.
The patch also removes the references to fb_memmove in the code that is
commented out because fb_memmove was removed from framebuffer subsystem.
There are two threads running on the system. The first thread is a system
monitoring thread that is reading /proc/modules. The second thread is
loading and unloading a module (in this example I'm using my simple
dummy-module.ko). Note, in the "real world" this occurred with the qlogic
driver module.
CPU 0 (/proc/modules reader)
CPU 1 (loading/unloading module)
CPU 0 opens /proc/modules, and starts displaying data for each module by
traversing the modules list via fs/seq_file.c:seq_open() and
fs/seq_file.c:seq_read(). For each module in the modules list, seq_read
does
op->start() <-- this is a pointer to m_start()
op->show() <- this is a pointer to m_show()
op->stop() <-- this is a pointer to m_stop()
The m_start(), m_show(), and m_stop() module functions are defined in
kernel/module.c. The m_start() and m_stop() functions acquire and release
the module_mutex respectively.
ie) When reading /proc/modules, the module_mutex is acquired and released
for each module.
m_show() is called with the module_mutex held. It accesses the module
struct data and attempts to write out module data. It is in this code
path that the above BUG_ON() warning is encountered, specifically m_show()
calls
The other thread, CPU 1, in unloading the module calls the syscall
delete_module() defined in kernel/module.c. The module_mutex is acquired
for a short time, and then released. free_module() is called without the
module_mutex. free_module() then sets mod->state = MODULE_STATE_UNFORMED,
also without the module_mutex. Some additional code is called and then the
module_mutex is reacquired to remove the module from the modules list:
/* Now we can delete it from the lists */
mutex_lock(&module_mutex);
stop_machine(__unlink_module, mod, NULL);
mutex_unlock(&module_mutex);
This is the sequence of events that leads to the panic.
CPU 1 is removing dummy_module via delete_module(). It acquires the
module_mutex, and then releases it. CPU 1 has NOT set dummy_module->state to
MODULE_STATE_UNFORMED yet.
CPU 0, which is reading the /proc/modules, acquires the module_mutex and
acquires a pointer to the dummy_module which is still in the modules list.
CPU 0 calls m_show for dummy_module. The check in m_show() for
MODULE_STATE_UNFORMED passed for dummy_module even though it is being
torn down.
Meanwhile CPU 1, which has been continuing to remove dummy_module without
holding the module_mutex, now calls free_module() and sets
dummy_module->state to MODULE_STATE_UNFORMED.
CPU 0 now calls module_flags() with dummy_module and ...
Acquire and release the module_mutex lock around the setting of
MODULE_STATE_UNFORMED in the teardown path, which should resolve the
problem.
Testing: In the unpatched kernel I can panic the system within 1 minute by
doing
while (true) do insmod dummy_module.ko; rmmod dummy_module.ko; done
and
while (true) do cat /proc/modules; done
in separate terminals.
In the patched kernel I was able to run just over one hour without seeing
any issues. I also verified the output of panic via sysrq-c and the output
of /proc/modules looks correct for all three states for the dummy_module.
SCSI-2/SPI actually needs the tagged/untagged flag in the request to
work properly. Revert this patch and add a follow on to set it in
the right place.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Acked-by: Jens Axboe <axboe@kernel.dk> Reported-by: Meelis Roos <mroos@linux.ee> Tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The math in both blk_stack_limits() and queue_limit_alignment_offset()
assume that a block device's io_min (aka minimum_io_size) is always a
power-of-2. Fix the math such that it works for non-power-of-2 io_min.
This issue (of alignment_offset != 0) became apparent when testing
dm-thinp with a thinp blocksize that matches a RAID6 stripesize of
1280K. Commit fdfb4c8c1 ("dm thin: set minimum_io_size to pool's data
block size") unlocked the potential for alignment_offset != 0 due to
the dm-thin-pool's io_min possibly being a non-power-of-2.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 98683650 "Merge branch 'drbd-8.4_ed6' into
for-3.8-drivers-drbd-8.4_ed6" switches to the new augment API, but the
new API requires that the tree is augmented before rb_insert_augmented()
is called, which is missing.
So we add the augment-code to drbd_insert_interval() when it travels the
tree up to down before rb_insert_augmented(). See the example in
include/linux/interval_tree_generic.h or Documentation/rbtree.txt.
drbd_insert_interval() may cancel the insertion when traveling, in this
case, the just added augment-code does nothing before cancel since the
@this node is already in the subtrees in this case.
CC: Michel Lespinasse <walken@google.com> Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Andreas Gruenbacher <agruen@linbit.com> Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When __scan frees the required number of buffer entries that the
shrinker requested (nr_to_scan becomes zero) it must return. Before
this fix the __scan code exited only the inner loop and continued in the
outer loop -- which could result in reduced performance due to extra
buffers being freed (e.g. unnecessarily evicted thinp metadata needing
to be synchronously re-read into bufio's cache).
Also, move dm_bufio_cond_resched to __scan's inner loop, so that
iterating the bufio client's lru lists doesn't result in scheduling
latency.
Reported-by: Joe Thornber <thornber@redhat.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'last_accessed' member of the dm_buffer structure was only set when
the the buffer was created. This led to each buffer being discarded
after dm_bufio_max_age time even if it was used recently. In practice
this resulted in all thinp metadata being evicted soon after being read
-- this is particularly problematic for metadata intensive workloads
like multithreaded small random IO.
'last_accessed' is now updated each time the buffer is moved to the head
of the LRU list, so the buffer is now properly discarded if it was not
used in dm_bufio_max_age time.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently divide the queue depth by 4 as our batch wakeup
count, but we split the wakeups over BT_WAIT_QUEUES number of
wait queues. This defaults to 8. If the product of the resulting
batch wake count and BT_WAIT_QUEUES is higher than the device
queue depth, we can get into a situation where a task goes to
sleep waiting for a request, but never gets woken up.
blkback does not unmap persistent grants when frontend goes to Closed
state (e.g. when blkfront module is being removed). This leads to the
following in guest's dmesg:
[ 343.243825] xen:grant_table: WARNING: g.e. 0x445 still in use!
[ 343.243825] xen:grant_table: WARNING: g.e. 0x42a still in use!
...
When load module -> use device -> unload module sequence is performed multiple times
it is possible to hit BUG() condition in blkfront module:
We don't need to keep these grants if we're disconnecting as frontend might already
forgot about them. Solve the issue by moving xen_blkbk_free_caches() call from
xen_blkif_free() to xen_blkif_disconnect().
Now we can see the following:
[ 928.590893] xen:grant_table: WARNING: g.e. 0x587 still in use!
[ 928.591861] xen:grant_table: WARNING: g.e. 0x372 still in use!
...
[ 929.592146] xen:grant_table: freeing g.e. 0x587
[ 929.597174] xen:grant_table: freeing g.e. 0x372
...
Backend does not keep persistent grants any more, reconnect works fine.
On restore, virtio pci does the following:
+ set features
+ init vqs etc - device can be used at this point!
+ set ACKNOWLEDGE,DRIVER and DRIVER_OK status bits
This is in violation of the virtio spec, which
requires the following order:
- ACKNOWLEDGE
- DRIVER
- init vqs
- DRIVER_OK
This behaviour will break with hypervisors that assume spec compliant
behaviour. It seems like a good idea to have this patch applied to
stable branches to reduce the support butden for the hypervisors.
Cc: Amit Shah <amit.shah@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: 856ee6115e2d ("charger-manager: Support deivce tree in charger manager driver") Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sb_finish_set_opts() can race with inode_free_security()
when initializing inode security structures for inodes
created prior to initial policy load or by the filesystem
during ->mount(). This appears to have always been
a possible race, but commit 3dc91d4 ("SELinux: Fix possible
NULL pointer dereference in selinux_inode_permission()")
made it more evident by immediately reusing the unioned
list/rcu element of the inode security structure for call_rcu()
upon an inode_free_security(). But the underlying issue
was already present before that commit as a possible use-after-free
of isec.
Shivnandan Kumar reported the list corruption and proposed
a patch to split the list and rcu elements out of the union
as separate fields of the inode_security_struct so that setting
the rcu element would not affect the list element. However,
this would merely hide the issue and not truly fix the code.
This patch instead moves up the deletion of the list entry
prior to dropping the sbsec->isec_lock initially. Then,
if the inode is dropped subsequently, there will be no further
references to the isec.
Reported-by: Shivnandan Kumar <shivnandan.k@samsung.com> Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For a PCI device, aliases from the IVRS table won't be populated
into dma_alias_devfn until after iommu_init_device() is called on
each device. We therefore want to split init_iommu_group() to
be called from a separate loop immediately following.
It turns out that our assumption that aliases are always to the same
slot isn't true. One particular platform reports an IVRS alias of the
SATA controller (00:11.0) for the legacy IDE controller (00:14.1).
When we hit this, we attempt to use a single IOMMU group for
everything on the same bus, which in this case is the root complex.
We already have multiple groups defined for the root complex by this
point, resulting in multiple WARN_ON hits.
This patch makes these sorts of aliases work again with IOMMU groups
by reworking how we search through the PCI address space to find
existing groups. This should also now handle looped dependencies and
all sorts of crazy inter-dependencies that we'll likely never see.
The recursion used here should never be very deep. It's unlikely to
have individual aliases and only theoretical that we'd ever see a
chain where one alias causes us to search through to yet another
alias. We're also only dealing with PCIe device on a single bus,
which means we'll typically only see multiple slots in use on the root
complex. Loops are also a theoretically possibility, which I've
tested using fake DMA alias quirks and prevent from causing problems
using a bitmap of the devfn space that's been visited.
pci_enable_msi() can return failure with both positive and negative
integers -- it returns 0 for success -- but is only tested here for
"if (ret < 0)". This causes us to try to use MSI on the RTS5249 SD
reader in the Dell XPS 11 when enabling MSI failed, causing:
[ 1.737110] rtsx_pci: probe of 0000:05:00.0 failed with error -110
Reported-by: D. Jared Dominguez <Jared_Dominguez@Dell.com> Tested-by: D. Jared Dominguez <Jared_Dominguez@Dell.com> Signed-off-by: Chris Ball <chris@printf.net> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the resume path, the ADC invokes am335x_tsc_se_set_cache() with 0 as
the steps argument if continous mode is not in use. This in turn disables
all steps and so the TSC is not working until one ADC sampling is
performed.
This patch fixes it by writing the current cached mask instead of the
passed steps.
Fixes: 7ca6740cd1cd ("mfd: input: iio: ti_amm335x: Rework TSC/ADCA
synchronization") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After enabling and disabling ADC continuous mode via sysfs, ts_print_raw
fails to return any data. This is because when ADC is configured for
continuous mode, it disables touch screen steps.These steps are not
re-enabled when ADC continuous mode is disabled. Therefore existing values
of REG_SE needs to be cached before enabling continuous mode and
disabling touch screen steps and enabling ADC steps. The cached value
are to be restored to REG_SE once ADC is disabled.
Fixes: 7ca6740cd1cd ("mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization") Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Lutomirski recently demonstrated that when chroot is used to set
the root path below the path for the new ``root'' passed to pivot_root
the pivot_root system call succeeds and leaks mounts.
In examining the code I see that starting with a new root that is
below the current root in the mount tree will result in a loop in the
mount tree after the mounts are detached and then reattached to one
another. Resulting in all kinds of ugliness including a leak of that
mounts involved in the leak of the mount loop.
Prevent this problem by ensuring that the new mount is reachable from
the current root of the mount tree.
[Added stable cc. Fixes CVE-2014-7970. --Andy]
Reported-by: Andy Lutomirski <luto@amacapital.net> Reviewed-by: Andy Lutomirski <luto@amacapital.net> Link: http://lkml.kernel.org/r/87bnpmihks.fsf@x220.int.ebiederm.org Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I ran into this error after a ubiupdatevol, because I forgot to backport e9110361a9a4 UBI: fix the volumes tree sorting criteria.
UBI error: process_pool_aeb: orphaned volume in fastmap pool
UBI error: ubi_scan_fastmap: Attach by fastmap failed, doing a full scan!
kmem_cache_destroy ubi_ainf_peb_slab: Slab cache still has objects
CPU: 0 PID: 1 Comm: swapper Not tainted 3.14.18-00053-gf05cac8dbf85 #1
[<c000d298>] (unwind_backtrace) from [<c000baa8>] (show_stack+0x10/0x14)
[<c000baa8>] (show_stack) from [<c01b7a68>] (destroy_ai+0x230/0x244)
[<c01b7a68>] (destroy_ai) from [<c01b8fd4>] (ubi_attach+0x98/0x1ec)
[<c01b8fd4>] (ubi_attach) from [<c01ade90>] (ubi_attach_mtd_dev+0x2b8/0x868)
[<c01ade90>] (ubi_attach_mtd_dev) from [<c038b510>] (ubi_init+0x1dc/0x2ac)
[<c038b510>] (ubi_init) from [<c0008860>] (do_one_initcall+0x94/0x140)
[<c0008860>] (do_one_initcall) from [<c037aadc>] (kernel_init_freeable+0xe8/0x1b0)
[<c037aadc>] (kernel_init_freeable) from [<c02730ac>] (kernel_init+0x8/0xe4)
[<c02730ac>] (kernel_init) from [<c00093f0>] (ret_from_fork+0x14/0x24)
UBI: scanning is finished
Freeing the cache in the error path fixes the Slab error.
Tested on at91sam9g35 (3.14.18+fastmap backports)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UBI_IOCVOLUP ioctl is used to start an update and also to
truncate a volume. In the first case, a "volume updated" notification
is dispatched when the update is done.
This commit adds the "volume updated" notification to be also sent when
the volume is truncated. This is required for UBI block and gluebi to get
notified about the new volume size.
Static volumes can change its 'used_bytes' when they get updated,
and so the block interface must listen to the UBI_VOLUME_UPDATED
notification to resize the block device accordingly.
We are currently taking the block device size from the ubi_volume_info.size
field. However, this is not the amount of data in the volume, but the
number of reserved physical eraseblocks, and hence leads to an incorrect
representation of the volume.
In particular, this produces I/O errors on static volumes as the block
interface may attempt to read unmapped PEBs:
$ cat /dev/ubiblock0_0 > /dev/null
UBI error: ubiblock_read_to_buf: ubiblock0_0 ubi_read error -22
end_request: I/O error, dev ubiblock0_0, sector 9536
Buffer I/O error on device ubiblock0_0, logical block 2384
[snip]
Fix this by using the ubi_volume_info.used_bytes field which is set to the
actual number of data bytes for both static and dynamic volumes.
While here, improve the error message to be less stupid and more useful:
UBI error: ubiblock_read_to_buf: ubiblock0_1 ubi_read error -9 on LEB=0, off=15872, len=512
It's worth noticing that the 512-byte sector representation of the volume
is only correct if the volume size is multiple of 512-bytes. This is true for
virtually any NAND device, given eraseblocks and pages are 512-byte multiple
and hence so is the LEB size.
Artem: tweak the error message and make it look more like other UBI error
messages.
Fixes: 9d54c8a33eec ("UBI: R/O block driver on top of UBI volumes") Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call to topology_init is too late for the set_sched_topology call.
The initial scheduling domain structure has already been established
with default topology array. Use the smp_cpus_done() call to get the
s390 specific topology array registered early enough.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
zatimend has reported that in his environment (3.16/gcc4.8.3/corei7)
memset() calls which clear out sensitive data in extract_{buf,entropy,
entropy_user}() in random driver are being optimized away by gcc.
Add a helper memzero_explicit() (similarly as explicit_bzero() variants)
that can be used in such cases where a variable with sensitive data is
being cleared out in the end. Other use cases might also be in crypto
code. [ I have put this into lib/string.c though, as it's always built-in
and doesn't need any dependencies then. ]
Starting with Linux 3.12 processes get stuck in D state forever in
UserModeLinux under sync heavy workloads. This bug was introduced by
commit 805f11a0d5 (um: ubd: Add REQ_FLUSH suppport).
Fix bug by adding a check if FLUSH request was successfully submitted to
the I/O thread and keeping the FLUSH request on the request queue on
submission failures.
Commit f363e45fd118 ("net/ceph: make ceph_msgr_wq non-reentrant")
effectively removed WQ_MEM_RECLAIM flag from ceph_msgr_wq. This is
wrong - libceph is very much a memory reclaim path, so restore it.
we used to check for "nobody else could start doing anything with
that opened file" by checking that refcount was 2 or less - one
for descriptor table and one we'd acquired in fget() on the way to
wherever we are. That was race-prone (somebody else might have
had a reference to descriptor table and do fget() just as we'd
been checking) and it had become flat-out incorrect back when
we switched to fget_light() on those codepaths - unlike fget(),
it doesn't grab an extra reference unless the descriptor table
is shared. The same change allowed a race-free check, though -
we are safe exactly when refcount is less than 2.
It was a long time ago; pre-2.6.12 for ioctl() (the codepath leading
to ppp one) and 2.6.17 for sendmsg() (netlink one). OTOH,
netlink hadn't grown that check until 3.9 and ppp used to live
in drivers/net, not drivers/net/ppp until 3.1. The bug existed
well before that, though, and the same fix used to apply in old
location of file.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
schedule_delayed_work() happening when the work is already pending is
a cheap no-op. Don't bother with ->wbuf_queued logics - it's both
broken (cancelling ->wbuf_dwork leaves it set, as spotted by Jeff Harris)
and pointless. It's cheaper to let schedule_delayed_work() handle that
case.
Reported-by: Jeff Harris <jefftharris@gmail.com> Tested-by: Jeff Harris <jefftharris@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AFAICS, prepend_name() is broken on SMP alpha. Disclaimer: I don't have
SMP alpha boxen to reproduce it on. However, it really looks like the race
is real.
CPU1: d_path() on /mnt/ramfs/<255-character>/foo
CPU2: mv /mnt/ramfs/<255-character> /mnt/ramfs/<63-character>
CPU2 does d_alloc(), which allocates an external name, stores the name there
including terminating NUL, does smp_wmb() and stores its address in
dentry->d_name.name. It proceeds to d_add(dentry, NULL) and d_move()
old dentry over to that. ->d_name.name value ends up in that dentry.
In the meanwhile, CPU1 gets to prepend_name() for that dentry. It fetches
->d_name.name and ->d_name.len; the former ends up pointing to new name
(64-byte kmalloc'ed array), the latter - 255 (length of the old name).
Nothing to force the ordering there, and normally that would be OK, since we'd
run into the terminating NUL and stop. Except that it's alpha, and we'd need
a data dependency barrier to guarantee that we see that store of NUL
__d_alloc() has done. In a similar situation dentry_cmp() would survive; it
does explicit smp_read_barrier_depends() after fetching ->d_name.name.
prepend_name() doesn't and it risks walking past the end of kmalloc'ed object
and possibly oops due to taking a page fault in kernel mode.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In compat mode, we copy each field of snd_pcm_status struct but don't
touch the reserved fields, and this leaves uninitialized values
there. Meanwhile the native ioctl does zero-clear the whole
structure, so we should follow the same rule in compat mode, too.
CMI8888 shows the stuttering playback when the snooping is disabled
on the audio buffer. Meanwhile, we've got reports that CORB/RIRB
doesn't work in the snooped mode. So, as a compromise, disable the
snoop only for CORB/RIRB and enable the snoop for the stream buffers.
The resultant patch became a bit ugly, unfortunately, but we still can
live with it.
evm_inode_setxattr() can be called with no value. The function does not
check the length so that following command can be used to produce the
kernel oops: setfattr -n security.evm FOO. This patch fixes it.
Changes in v3:
* there is no reason to return different error codes for EVM_XATTR_HMAC
and non EVM_XATTR_HMAC. Remove unnecessary test then.
Changes in v2:
* testing for validity of xattr type
Unless an LSM labels a file during d_instantiate(), newly created
files are not labeled with an initial security.evm xattr, until
the file closes. EVM, before allowing a protected, security xattr
to be written, verifies the existing 'security.evm' value is good.
For newly created files without a security.evm label, this
verification prevents writing any protected, security xattrs,
until the file closes.
Following is the example when this happens:
fd = open("foo", O_CREAT | O_WRONLY, 0644);
setxattr("foo", "security.SMACK64", value, sizeof(value), 0);
close(fd);
While INTEGRITY_NOXATTRS status is handled in other places, such
as evm_inode_setattr(), it does not handle it in all cases in
evm_protect_xattr(). By limiting the use of INTEGRITY_NOXATTRS to
newly created files, we can now allow setting "protected" xattrs.
Changelog:
- limit the use of INTEGRITY_NOXATTRS to IMA identified new files
The idiot who did 4a1c0f262f88 ("perf: Fix lockdep warning on process exit")
forgot to pay attention and fix all similar cases. Do so now.
In particular, unclone_ctx() must be called while holding ctx->lock,
therefore all such sites are broken for the same reason. Pull the
put_ctx() call out from under ctx->lock.
Reported-by: Sasha Levin <sasha.levin@oracle.com> Probably-also-reported-by: Vince Weaver <vincent.weaver@maine.edu> Fixes: 4a1c0f262f88 ("perf: Fix lockdep warning on process exit") Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Cong Wang <cwang@twopensource.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: http://lkml.kernel.org/r/20140930172308.GI4241@worktop.programming.kicks-ass.net Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pte_pfn() returns a PFN of long (32 bits in 32-PAE), so "long <<
PAGE_SHIFT" will overflow for PFNs above 4GB.
Due to this issue, some Linux 32-PAE distros, running as guests on Hyper-V,
with 5GB memory assigned, can't load the netvsc driver successfully and
hence the synthetic network device can't work (we can use the kernel parameter
mem=3000M to work around the issue).
Rusty noticed a Really Bad Bug (tm) in my NT fix. The entry code
reads out of bounds, causing the NT fix to be unreliable. But, and
this is much, much worse, if your stack is somehow just below the
top of the direct map (or a hole), you read out of bounds and crash.
That read is deterministically above the top of the stack. I
thought I even single-stepped through this code when I wrote it to
check the offset, but I clearly screwed it up.
Fixes: 8c7aa698baca ("x86_64, entry: Filter RFLAGS.NT on entry from userspace") Reported-by: Rusty Russell <rusty@ozlabs.org> Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NT flag doesn't do anything in long mode other than causing IRET
to #GP. Oddly, CPL3 code can still set NT using popf.
Entry via hardware or software interrupt clears NT automatically, so
the only relevant entries are fast syscalls.
If user code causes kernel code to run with NT set, then there's at
least some (small) chance that it could cause trouble. For example,
user code could cause a call to EFI code with NT set, and who knows
what would happen? Apparently some games on Wine sometimes do
this (!), and, if an IRET return happens, they will segfault. That
segfault cannot be handled, because signal delivery fails, too.
This patch programs the CPU to clear NT on entry via SYSCALL (both
32-bit and 64-bit, by my reading of the AMD APM), and it clears NT
in software on entry via SYSENTER.
To save a few cycles, this borrows a trick from Jan Beulich in Xen:
it checks whether NT is set before trying to clear it. As a result,
it seems to have very little effect on SYSENTER performance on my
machine.
There's another minor bug fix in here: it looks like the CFI
annotations were wrong if CONFIG_AUDITSYSCALL=n.
Testers beware: on Xen, SYSENTER with NT set turns into a GPF.
I haven't touched anything on 32-bit kernels.
The syscall mask change comes from a variant of this patch by Anish
Bhatt.
Note to stable maintainers: there is no known security issue here.
A misguided program can set NT and cause the kernel to try and fail
to deliver SIGSEGV, crashing the program. This patch fixes Far Cry
on Wine: https://bugs.winehq.org/show_bug.cgi?id=33275
save_xstate_sig()->drop_init_fpu() doesn't look right. setup_rt_frame()
can fail after that, in this case the next setup_rt_frame() triggered
by SIGSEGV won't save fpu simply because the old state was lost. This
obviously mean that fpu won't be restored after sys_rt_sigreturn() from
SIGSEGV handler.
Shift drop_init_fpu() into !failed branch in handle_signal().
Add preempt_disable() + preempt_enable() around math_state_restore() in
__restore_xstate_sig(). Otherwise __switch_to() after __thread_fpu_begin()
can overwrite fpu->state we are going to restore.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Link: http://lkml.kernel.org/r/20140902175717.GA21649@redhat.com Reviewed-by: Suresh Siddha <sbsiddha@gmail.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is currently possible to execve() an x32 executable on an x86_64
kernel that has only ia32 compat enabled. However all its syscalls
will fail, even _exit(). This usually causes it to segfault.
Change the ELF compat architecture check so that x32 executables are
rejected if we don't support the x32 ABI.
->page_mkwrite() is used by filesystems to allocate blocks under a page
which is becoming writeably mmapped in some process' address space. This
allows a filesystem to return a page fault if there is not enough space
available, user exceeds quota or similar problem happens, rather than
silently discarding data later when writepage is called.
However VFS fails to call ->page_mkwrite() in all the cases where
filesystems need it when blocksize < pagesize. For example when
blocksize = 1024, pagesize = 4096 the following is problematic:
ftruncate(fd, 0);
pwrite(fd, buf, 1024, 0);
map = mmap(NULL, 1024, PROT_WRITE, MAP_SHARED, fd, 0);
map[0] = 'a'; ----> page_mkwrite() for index 0 is called
ftruncate(fd, 10000); /* or even pwrite(fd, buf, 1, 10000) */
mremap(map, 1024, 10000, 0);
map[4095] = 'a'; ----> no page_mkwrite() called
At the moment ->page_mkwrite() is called, filesystem can allocate only
one block for the page because i_size == 1024. Otherwise it would create
blocks beyond i_size which is generally undesirable. But later at
->writepage() time, we also need to store data at offset 4095 but we
don't have block allocated for it.
This patch introduces a helper function filesystems can use to have
->page_mkwrite() called at all the necessary moments.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hu (hujianyang <hujianyang@huawei.com>) discovered an issue in the
'empty_log_bytes()' function, which calculates how many bytes are left in the
log:
"
If 'c->lhead_lnum + 1 == c->ltail_lnum' and 'c->lhead_offs == c->leb_size', 'h'
would equalent to 't' and 'empty_log_bytes()' would return 'c->log_bytes'
instead of 0.
"
At this point it is not clear what would be the consequences of this, and
whether this may lead to any problems, but this patch addresses the issue just
in case.
Hu (hujianyang@huawei.com) discovered a race condition which may lead to a
situation when UBIFS is unable to mount the file-system after an unclean
reboot. The problem is theoretical, though.
In UBIFS, we have the log, which basically a set of LEBs in a certain area. The
log has the tail and the head.
Every time user writes data to the file-system, the UBIFS journal grows, and
the log grows as well, because we append new reference nodes to the head of the
log. So the head moves forward all the time, while the log tail stays at the
same position.
At any time, the UBIFS master node points to the tail of the log. When we mount
the file-system, we scan the log, and we always start from its tail, because
this is where the master node points to. The only occasion when the tail of the
log changes is the commit operation.
The commit operation has 2 phases - "commit start" and "commit end". The former
is relatively short, and does not involve much I/O. During this phase we mostly
just build various in-memory lists of the things which have to be written to
the flash media during "commit end" phase.
During the commit start phase, what we do is we "clean" the log. Indeed, the
commit operation will index all the data in the journal, so the entire journal
"disappears", and therefore the data in the log become unneeded. So we just
move the head of the log to the next LEB, and write the CS node there. This LEB
will be the tail of the new log when the commit operation finishes.
When the "commit start" phase finishes, users may write more data to the
file-system, in parallel with the ongoing "commit end" operation. At this point
the log tail was not changed yet, it is the same as it had been before we
started the commit. The log head keeps moving forward, though.
The commit operation now needs to write the new master node, and the new master
node should point to the new log tail. After this the LEBs between the old log
tail and the new log tail can be unmapped and re-used again.
And here is the possible problem. We do 2 operations: (a) We first update the
log tail position in memory (see 'ubifs_log_end_commit()'). (b) And then we
write the master node (see the big lock of code in 'do_commit()').
But nothing prevents the log head from moving forward between (a) and (b), and
the log head may "wrap" now to the old log tail. And when the "wrap" happens,
the contends of the log tail gets erased. Now a power cut happens and we are in
trouble. We end up with the old master node pointing to the old tail, which was
erased. And replay fails because it expects the master node to point to the
correct log tail at all times.
This patch merges the abovementioned (a) and (b) operations by moving the master
node change code to the 'ubifs_log_end_commit()' function, so that it runs with
the log mutex locked, which will prevent the log from being changed benween
operations (a) and (b).
The man page for open(2) indicates that when O_CREAT is specified, the
'mode' argument applies only to future accesses to the file:
Note that this mode applies only to future accesses of the newly
created file; the open() call that creates a read-only file
may well return a read/write file descriptor.
The man page for open(2) implies that 'mode' is treated identically by
O_CREAT and O_TMPFILE.
But for O_TMPFILE, do_tmpfile() passes the full op->acc_mode to
may_open().
This patch lines up the behavior of O_TMPFILE with O_CREAT. After the
inode is created, may_open() is called with acc_mode = MAY_OPEN, in
do_tmpfile().
A different, but related glibc bug revealed the discrepancy:
https://sourceware.org/bugzilla/show_bug.cgi?id=17523
The glibc lazily loads the 'mode' argument of open() and openat() using
va_arg() only if O_CREAT is present in 'flags' (to support both the 2
argument and the 3 argument forms of open; same idea for openat()).
However, the glibc ignores the 'mode' argument if O_TMPFILE is in
'flags'.
On x86_64, for open(), it magically works anyway, as 'mode' is in
RDX when entering open(), and is still in RDX on SYSCALL, which is where
the kernel looks for the 3rd argument of a syscall.
But openat() is not quite so lucky: 'mode' is in RCX when entering the
glibc wrapper for openat(), while the kernel looks for the 4th argument
of a syscall in R10. Indeed, the syscall calling convention differs from
the regular calling convention in this respect on x86_64. So the kernel
sees mode = 0 when trying to use glibc openat() with O_TMPFILE, and
fails with EACCES.
Signed-off-by: Eric Rannaud <e@nanocritical.com> Acked-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While total_objects is a "long", total_objects == 0 unlikely happens for
3.12 and later kernels because 32-bit architectures would not be able to
hold (1 << 32) objects. However, total_objects == 0 may happen for kernels
between 3.1 and 3.11 because total_objects in prune_super() was an "int"
and (e.g.) x86_64 architecture might be able to hold (1 << 32) objects.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes it possible to kill a process looping in
cont_expand_zero. A process may spend a lot of time in this function, so
it is desirable to be able to kill it.
It happened to me that I wanted to copy a piece data from the disk to a
file. By mistake, I used the "seek" parameter to dd instead of "skip". Due
to the "seek" parameter, dd attempted to extend the file and became stuck
doing so - the only possibility was to reset the machine or wait many
hours until the filesystem runs out of space and cont_expand_zero fails.
We need this patch to be able to terminate the process.
Runtime Power Management handling for the sdhci_add_host() failure
case in sdhci_s3c_probe() should match the code in sdhci_s3c_remove()
(which uses pm_runtime_disable() call which matches the earlier
pm_runtime_enable() one). Fix it.
This patch fixes "BUG: spinlock bad magic on CPU#0, swapper/0/1" and
"Unbalanced pm_runtime_enable!" warnings.
>From the kernel log:
...
[ 1.659631] s3c-sdhci 12530000.sdhci: sdhci_add_host() failed
[ 1.665096] BUG: spinlock bad magic on CPU#0, swapper/0/1
[ 1.670433] lock: 0xea01e484, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
[ 1.677895] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.16.0-next-20140804-00008-ga59480f-dirty #707
[ 1.687037] [<c0013ae4>] (unwind_backtrace) from [<c0010d70>] (show_stack+0x10/0x14)
[ 1.694740] [<c0010d70>] (show_stack) from [<c04050c8>] (dump_stack+0x68/0xb8)
[ 1.701948] [<c04050c8>] (dump_stack) from [<c0052558>] (do_raw_spin_lock+0x15c/0x1a4)
[ 1.709848] [<c0052558>] (do_raw_spin_lock) from [<c040a630>] (_raw_spin_lock_irqsave+0x20/0x28)
[ 1.718619] [<c040a630>] (_raw_spin_lock_irqsave) from [<c030d7d0>] (sdhci_do_set_ios+0x1c/0x5cc)
[ 1.727464] [<c030d7d0>] (sdhci_do_set_ios) from [<c030ddfc>] (sdhci_runtime_resume_host+0x50/0x104)
[ 1.736574] [<c030ddfc>] (sdhci_runtime_resume_host) from [<c02462dc>] (pm_generic_runtime_resume+0x2c/0x40)
[ 1.746383] [<c02462dc>] (pm_generic_runtime_resume) from [<c0247898>] (__rpm_callback+0x34/0x70)
[ 1.755233] [<c0247898>] (__rpm_callback) from [<c02478fc>] (rpm_callback+0x28/0x88)
[ 1.762958] [<c02478fc>] (rpm_callback) from [<c02486f0>] (rpm_resume+0x384/0x4ec)
[ 1.770511] [<c02486f0>] (rpm_resume) from [<c02488b0>] (pm_runtime_forbid+0x58/0x64)
[ 1.778325] [<c02488b0>] (pm_runtime_forbid) from [<c030ea70>] (sdhci_s3c_probe+0x4a4/0x540)
[ 1.786749] [<c030ea70>] (sdhci_s3c_probe) from [<c02429cc>] (platform_drv_probe+0x2c/0x5c)
[ 1.795076] [<c02429cc>] (platform_drv_probe) from [<c02415f0>] (driver_probe_device+0x114/0x234)
[ 1.803929] [<c02415f0>] (driver_probe_device) from [<c024179c>] (__driver_attach+0x8c/0x90)
[ 1.812347] [<c024179c>] (__driver_attach) from [<c023ffb4>] (bus_for_each_dev+0x54/0x88)
[ 1.820506] [<c023ffb4>] (bus_for_each_dev) from [<c0240df8>] (bus_add_driver+0xd8/0x1cc)
[ 1.828665] [<c0240df8>] (bus_add_driver) from [<c0241db8>] (driver_register+0x78/0xf4)
[ 1.836652] [<c0241db8>] (driver_register) from [<c00088a4>] (do_one_initcall+0x80/0x1d0)
[ 1.844816] [<c00088a4>] (do_one_initcall) from [<c059ac94>] (kernel_init_freeable+0x108/0x1d4)
[ 1.853503] [<c059ac94>] (kernel_init_freeable) from [<c0401300>] (kernel_init+0x8/0xe4)
[ 1.861568] [<c0401300>] (kernel_init) from [<c000e538>] (ret_from_fork+0x14/0x3c)
[ 1.869582] platform 12530000.sdhci: Driver s3c-sdhci requests probe deferral
...
[ 1.997047] s3c-sdhci 12530000.sdhci: Unbalanced pm_runtime_enable!
...
[ 2.027235] s3c-sdhci 12530000.sdhci: sdhci_add_host() failed
[ 2.032884] platform 12530000.sdhci: Driver s3c-sdhci requests probe deferral
...
Tested on Hardkernel's Exynos4412 based ODROID-U3 board.
Fixes: 9f4e8151dbbc ("mmc: sdhci-s3c: Enable runtime power management") Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.
Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.
As soon as the CD IRQ is requested, it can trigger, since it's an
externally controlled event. If it does, delayed_work host->detect will
be scheduled.
Many host controller probe()s are roughly structured as:
In 3.17, CD IRQs can are enabled quite early via *_probe() ->
mmc_of_parse() -> mmc_gpio_request_cd() -> mmc_gpiod_request_cd_irq().
Note that in linux-next, mmc_of_parse() calls mmc_gpio*d*_request_cd()
rather than mmc_gpio_request_cd(), and mmc_gpio*d*_request_cd() doesn't
call mmc_gpiod_request_cd_irq(). However, this issue still exists if
mmc_gpio_request_cd() is called directly before mmc_start_host().
sdhci_add_host() may fail part way through (e.g. due to deferred
probe for a vmmc regulator), and sdhci_pltfm_free() does nothing to
unrequest the CD IRQ nor cancel the delayed_work. sdhci_pltfm_free() is
coded to assume that if sdhci_add_host() failed, then the delayed_work
cannot (or should not) have been triggered.
This can lead to the following with CONFIG_DEBUG_OBJECTS_* enabled, when
kfree(host) is eventually called inside sdhci_pltfm_free():
WARNING: CPU: 2 PID: 6 at lib/debugobjects.c:263 debug_print_object+0x8c/0xb4()
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x18
The object being complained about is host->detect.
There's no need to request the CD IRQ so early; mmc_start_host() already
requests it. For most SDHCI hosts at least, the typical call path that
does this is: *_probe() -> sdhci_add_host() -> mmc_add_host() ->
mmc_start_host(). Therefore, remove the call to mmc_gpiod_request_cd_irq()
from mmc_gpio_request_cd(). This also matches mmc_gpio*d*_request_cd(),
which already doesn't call mmc_gpiod_request_cd_irq().
However, some host controller drivers call mmc_gpio_request_cd() after
mmc_start_host() has already been called, and assume that this will also
call mmc_gpiod_request_cd_irq(). Update those drivers to explicitly call
mmc_gpiod_request_cd_irq() themselves. Ideally, these drivers should be
modified to move their call to mmc_gpio_request_cd() before their call
to mmc_add_host(). However that's too large a change for stable.
This solves the problem (eliminates the kernel error message above),
since it guarantees that the IRQ can't trigger before mmc_start_host()
is called.
The critical point here is that once sdhci_add_host() calls
mmc_add_host() -> mmc_start_host(), sdhci_add_host() is coded not to
fail. In other words, if there's a chance that mmc_start_host() may have
been called, and CD IRQs triggered, and the delayed_work scheduled,
sdhci_add_host() won't fail, and so cleanup is no longer via
sdhci_pltfm_free() (which doesn't free the IRQ or cancel the work queue)
but instead must be via sdhci_remove_host(), which calls mmc_remove_host()
-> mmc_stop_host(), which does free the IRQ and cancel the work queue.
CC: Russell King <linux@arm.linux.org.uk> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexandre Courbot <acourbot@nvidia.com> Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.
Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.
.set_uhs_signaling field is currently initialised twice once to the
arch specific callback pxav3_set_uhs_signaling, and also to the generic
sdhci_set_uhs_signaling callback.
This means that uhs is currently broken for this platform currently, as pxav3
has some special constriants which means it can't use the generic callback.
This happened in
commit 96d7b78cfc2f ("mmc: sdhci: convert sdhci_set_uhs_signaling() into a library function")
commit a702c8abb2a9 ("mmc: host: split up sdhci-pxa, create sdhci-pxav3.c")'
Fix this and hopefully prevent it happening in the future by ensuring named
initialisers always follow the declaration order in the structure definition.
781e989cf59 ("mmc: sdhci: convert to new SDIO IRQ handling") and bf3b5ec66bd ("mmc: sdio_irq: rework sdio irq handling") disabled
the use of our own custom threaded IRQ handler, but left in an
unconditional wake_up_process() on that handler at resume-time. Link: https://bugzilla.kernel.org/show_bug.cgi?id=80151
In addition, the check for MMC_CAP_SDIO_IRQ capability is added
before enable sdio IRQ.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <chris@printf.net> Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current caching implementation during regcache_sync() call bypasses
all register writes of values that are already known as default
(regmap reg_defaults). Same time in TLV320AIC3x codecs register 5
(AIC3X_PLL_PROGC_REG) write should be immediately followed by register
6 write (AIC3X_PLL_PROGD_REG) even if it was not changed. Otherwise
both registers will not be written.
This brings to issue that appears particulary in case of 44.1kHz
playback with 19.2MHz master clock. In this case AIC3X_PLL_PROGC_REG
is 0x6e while AIC3X_PLL_PROGD_REG is 0x0 (same as register
default). Thus AIC3X_PLL_PROGC_REG also remains not written and we get
wrong playback speed.
In this patch snd_soc_read() is used to get cached pll values and
snd_soc_write() (unlike regcache_sync() this function doesn't bypasses
hardware default values) to write them to registers.
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the SNDRV_PCM_STREAM_CAPTURE branch in soc_pcm_apply_msb(), look at
sig_bits of the capture stream, not the playback one.
Spotted by coverity.
Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coverity spotted the following possible use-after-free condition in
dapm_create_or_share_mixmux_kcontrol():
If kcontrol is NULL, and (wname_in_long_name && kcname_in_long_name)
validates to true, 'name' will be set to an allocated string, and be
freed a few lines later via the 'long_name' alias. 'name', however,
is used by dev_err() in case snd_ctl_add() fails.
Fix this by adding a jump label that frees 'long_name' at the end of
the function.
Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coverity spotted an use-after-free condition in snd_soc_remove_platform().
Fix this by moving snd_soc_component_cleanup() after the debug print
statement which uses the component's string.
Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, ata_sff_softreset is skipped for controllers with no ctl port.
But that also skips ata_sff_dev_classify required for device detection.
This means that libata is currently broken on controllers with no ctl port.
The Broadcom OSB4 IDE Controller (vendor and device IDs: 1166:0211)
does not support 64-KB DMA transfers.
Whenever a 64-KB DMA transfer is attempted,
the transfer fails and messages similar to the following
are written to the console log:
[ 2431.851125] sr 0:0:0:0: [sr0] Unhandled sense code
[ 2431.851139] sr 0:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 2431.851152] sr 0:0:0:0: [sr0] Sense Key : Hardware Error [current]
[ 2431.851166] sr 0:0:0:0: [sr0] Add. Sense: Logical unit communication time-out
[ 2431.851182] sr 0:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 76 f4 00 00 40 00
[ 2431.851210] end_request: I/O error, dev sr0, sector 121808
When the libata and pata_serverworks modules
are recompiled with ATA_DEBUG and ATA_VERBOSE_DEBUG defined in libata.h,
the 64-KB transfer size in the scatter-gather list can be seen
in the console log:
lspci shows that the driver used for the Broadcom OSB4 IDE Controller is
pata_serverworks:
00:0f.1 IDE interface: Broadcom OSB4 IDE Controller (prog-if 8e [Master SecP SecO PriP])
Flags: bus master, medium devsel, latency 64
[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
[virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
I/O ports at 0170 [size=8]
I/O ports at 0374 [size=4]
I/O ports at 1440 [size=16]
Kernel driver in use: pata_serverworks
The pata_serverworks driver supports five distinct device IDs,
one being the OSB4 and the other four belonging to the CSB series.
The CSB series appears to support 64-KB DMA transfers,
as tests on a machine with an SAI2 motherboard
containing a Broadcom CSB5 IDE Controller (vendor and device IDs: 1166:0212)
showed no problems with 64-KB DMA transfers.
This problem was first discovered when attempting to install openSUSE
from a DVD on a machine with an STL2 motherboard.
Using the pata_serverworks module,
older releases of openSUSE will not install at all due to the timeouts.
Releases of openSUSE prior to 11.3 can be installed by disabling
the pata_serverworks module using the brokenmodules boot parameter,
which causes the serverworks module to be used instead.
Recent releases of openSUSE (12.2 and later) include better error recovery and
will install, though very slowly.
On all openSUSE releases, the problem can be recreated
on a machine containing a Broadcom OSB4 IDE Controller
by mounting an install DVD and running a command similar to the following:
find /mnt -type f -print | xargs cat > /dev/null
The patch below corrects the problem.
Similar to the other ATA drivers that do not support 64-KB DMA transfers,
the patch changes the ata_port_operations qc_prep vector to point to a routine
that breaks any 64-KB segment into two 32-KB segments and
changes the scsi_host_template sg_tablesize element to reduce by half
the number of scatter/gather elements allowed.
These two changes affect only the OSB4.
Signed-off-by: Scott Carter <ccscott@funsoft.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3189eddbcafc ("percpu: free percpu allocation info for
uniprocessor system").
The commit causes a hang with a crisv32 image. This may be an architecture
problem, but at least for now the revert is necessary to be able to boot a
crisv32 image.
Cc: Tejun Heo <tj@kernel.org> Cc: Honggang Li <enjoymindful@gmail.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Tejun Heo <tj@kernel.org> Fixes: 3189eddbcafc ("percpu: free percpu allocation info for uniprocessor system") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flag RPC_CLNT_CREATE_NO_RETRANS_TIMEOUT was intended introduced in
order to allow NFSv4 clients to disable resend timeouts. Since those
cause the RPC layer to break the connection, they mess up the duplicate
reply caches that remain indexed on the port number in NFSv4..
This patch includes the code that was missing in the original to
set the appropriate flag in struct rpc_clnt, when the caller of
rpc_create() sets RPC_CLNT_CREATE_NO_RETRANS_TIMEOUT.
When aborting a connection to preserve source ports, don't wake the task in
xs_error_report. This allows tasks with RPC_TASK_SOFTCONN to succeed if the
connection needs to be re-established since it preserves the task's status
instead of setting it to the status of the aborting kernel_connect().
This may also avoid a potential conflict on the socket's lock.
The commit 3b57de958e2a brought the support for a different amount of the
filter bins, but didn't update the PCI driver accordingly. This patch appends
the default values when the device is enumerated via PCI bus.
Fixes: 3b57de958e2a (net: stmmac: Support devicetree configs for mcast and ucast filter entries) Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drivers now call ipv6_proxy_select_ident(), which is defined
only if CONFIG_INET is enabled. However, they have really depended
on CONFIG_INET for as long as they have allowed sending GSO packets
from userland.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Fixes: f43798c27684 ("tun: Allow GSO using virtio_net_hdr") Fixes: b9fb9ee07e67 ("macvtap: add GSO/csum offload support") Fixes: 5188cd44c55d ("drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UFO is now disabled on all drivers that work with virtio net headers,
but userland may try to send UFO/IPv6 packets anyway. Instead of
sending with ID=0, we should select identifiers on their behalf (as we
used to).
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Fixes: 916e4cf46d02 ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, skb_inner_network_header is used but this does not account
for Ethernet header for ETH_P_TEB. Use skb_inner_mac_header which
handles TEB and also should work with IP encapsulation in which case
inner mac and inner network headers are the same.
Tested: Ran TCP_STREAM over GRE, worked as expected.
Signed-off-by: Tom Herbert <therbert@google.com> Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If mlx4_ib_create_flow() attempts to create > 1 rules with the
firmware, and one of these registrations fail, we leaked the
already created flow rules.
One example of the leak is when the registration of the VXLAN ghost
steering rule fails, we didn't unregister the original rule requested
by the user, introduced in commit d2fce8a9060d "mlx4: Set
user-space raw Ethernet QPs to properly handle VXLAN traffic".
While here, add dump of the VXLAN portion of steering rules
so it can actually be seen when flow creation fails.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
