Fix problem where playback of Denon DA-300USB DAC sometimes does not
start and leads to error messages like "clock source 41 is not valid,
cannot use".
Solution: Treat this device the same as other Denon/Marantz devices in
sound/usb/quirks.c.
Tested with both PCM and DSD formats.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93261 Signed-off-by: Frank C Guenther <bugzilla.frnkcg@spamgourmet.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Then we use it as an offset into a array with SNDRV_CARDS elements.
if (!request_region(joystick_port[dev], 8, "Riptide gameport")) {
This has 3 effects:
1) If you use the module option to specify the joystick port then it has
to be shifted one space over.
2) The wrong error message will be printed on failure if you have over
32 cards.
3) Static checkers will correctly complain that are off by one.
On some Braswell systems BIOS leaves resets for SPI host controllers
active. This prevents the SPI driver from transferring messages on wire.
Fix this in similar way that we do for I2C already by deasserting resets
for the SPI host controllers.
Reported-by: Yang A Fang <yang.a.fang@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Baytrail and Braswell the BIOS might leave the I2C host controllers
enabled, probably because it uses them for its own purposes. This is fine
in normal cases because the I2C driver will disable the hardware when it
is probed anyway.
However, in case of suspend to disk it is different story. If the driver
happens to be compiled as a module the boot kernel never loads the driver
thus leaving host controllers enabled upon loading the hibernation image.
The I2C host controller interrupt mask register has default value of 0x8ff,
in other words it has most of the interrupts unmasked. When combined with
the fact that the host controller is enabled, the driver immediately starts
getting interrupts even before its resume hook is called (once IO-APIC is
resumed). Since the driver is not prepared for this it will crash the
kernel due to NULL pointer derefence because dev->msgs is NULL.
Unfortunately we were not able to get full backtrace to from the console
which could be reproduced here.
In order to fix this even when the driver is compiled as module, we disable
the I2C host controllers in byt_i2c_setup() before devices are created.
Reported-by: Yu Chen <yu.c.chen@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A request in the ring buffer mustn't be read after it has been marked
as consumed. Otherwise it might already have been reused by the
frontend without violating the ring protocol.
To avoid inconsistencies in the backend only work on a private copy
of the request. This will ensure a malicious guest not being able to
bypass consistency checks of the backend by modifying an active
request.
Commit 61a734d305e1 ("xen/manage: Always freeze/thaw processes when
suspend/resuming") ensured that userspace processes were always frozen
before suspending to reduce interaction issues when resuming devices.
However, freeze_processes() does not freeze kernel threads. Freeze
kernel threads as well to prevent deadlocks with the khubd thread when
resuming devices.
Commit 32726d2d550 ("ARM: SAMSUNG: Remove legacy clock code")
already removed the callback pointer, but there was one remaining
user:
drivers/cpufreq/s3c24xx-cpufreq.c: In function 's3c_cpufreq_resume_clocks':
drivers/cpufreq/s3c24xx-cpufreq.c:149:14: error: 'struct s3c_cpufreq_info' has no member named 'resume_clocks'
cpu_cur.info->resume_clocks();
^
The two functions s3c2416_cpufreq_driver_init and s3c_cpufreq_register
are marked init but are called from a context that might be run after
the __init sections are discarded, as the compiler points out:
WARNING: vmlinux.o(.data+0x1ad9dc): Section mismatch in reference from the variable s3c2416_cpufreq_driver to the function .init.text:s3c2416_cpufreq_driver_init()
WARNING: drivers/built-in.o(.text+0x35b5dc): Section mismatch in reference from the function s3c2410a_cpufreq_add() to the function .init.text:s3c_cpufreq_register()
This removes the __init markings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Dell Latitude C600 laptop with Pentium 3 850MHz processor, the
speedstep-smi driver sometimes loads and sometimes doesn't load with
"change to state X failed" message.
The hardware sometimes refuses to change frequency and in this case, we
need to retry later. I found out that we need to enable interrupts while
waiting. When we enable interrupts, the hardware blockage that prevents
frequency transition resolves and the transition is possible. With
disabled interrupts, the blockage doesn't resolve (no matter how long do
we wait). The exact reasons for this hardware behavior are unknown.
This patch enables interrupts in the function speedstep_set_state that can
be called with disabled interrupts. However, this function is called with
disabled interrupts only from speedstep_get_freqs, so it shouldn't cause
any problem.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In __cpufreq_remove_dev_finish(), per-cpu 'cpufreq_cpu_data' needs
to be cleared before calling kobject_put(&policy->kobj) and under
cpufreq_driver_lock. Otherwise, if someone else calls cpufreq_cpu_get()
in parallel with it, they can obtain a non-NULL policy from that after
kobject_put(&policy->kobj) was executed.
Consider this case:
Thread A Thread B
cpufreq_cpu_get()
acquire cpufreq_driver_lock
read-per-cpu cpufreq_cpu_data
kobject_put(&policy->kobj);
kobject_get(&policy->kobj);
...
per_cpu(&cpufreq_cpu_data, cpu) = NULL
cpufreq_cpu_get() gets the policy from per-cpu variable cpufreq_cpu_data
under cpufreq_driver_lock, and once it gets a valid policy it expects it
to not be freed until cpufreq_cpu_put() is called.
But the race happens when another thread puts the kobject first and updates
cpufreq_cpu_data before or later. And so the first thread gets a valid policy
structure and before it does kobject_get() on it, the second one has already
done kobject_put().
Fix this by setting cpufreq_cpu_data to NULL before putting the kobject and that
too under locks.
In commit e9538cf4f907 ("rtlwifi: Fix error when accessing unmapped memory
in skb"), a printk was included to indicate that the condition had been
reached. There is now enough evidence from other users that the fix is
working. That logging statement can now be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver utilizes a FIFO buffer for RX descriptors. There are four places
in the code where it calculates the number of free slots. Several of those
locations do the calculation incorrectly. To fix these and to prevent future
mistakes, a common inline routine is created.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are instances where the DMA engine stalls. The new code detects
such stalls and restarts DMA without needing a power reset.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The firmware supplies two kinds of packets via the RX mechanism. Besides the
normal data received over the air, these packets may contain bluetooth status
and other information. The present code fails to detect which kind of
information was received.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initially, the routine to update the write point in the FIFO buffer was
coded to save CPU time by not doing the calculation every interrupt. This
was an error and results in TX hangs.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the buffer descriptor index exceeds 2, then a TX HANG condition
will result.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An earlier bug fix of mine made the SND_DM365_VOICE_CODEC symbol
tristate to avoid creating an undefined reference from the
davinci-vcif.c driver to the davinci_soc_platform_register
function that may be in a module.
However, this may now lead to a different error on randconfig
kernels:
This happens because we now have a choice statement with
one bool and one tristate option, and the latter might not
support being set to 'y' because of dependencies.
This new change turns the other option into 'tristate' as well,
which avoids the problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 19926c6de0c3 ("ASoC: davinci: vcif must be a module if SND_DAVINCI_SOC is") Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f6b2a04590bb ("ASoC: pxa: mioa701_wm9713: Convert to table based DAPM
setup") converted the driver to register the board level DAPM elements with
the card's DAPM context rather than the CODEC's DAPM context. The change
overlooked that the speaker widget event callback accesses the widget's
codec field which is only valid if the widget has been registered in a CODEC
DAPM context. This patch modifies the callback to take an alternative route
to get the CODEC.
Fixes: f6b2a04590bb ("ASoC: pxa: mioa701_wm9713: Convert to table based DAPM
setup") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rt5677 codec has gained code that requires SPI to work correctly,
but there is no provision in Kconfig to prevent the driver from
being used when SPI is disabled or a loadable module, resulting
in this build error:
sound/built-in.o: In function `rt5677_spi_write':
:(.text+0xa7ba0): undefined reference to `spi_sync'
sound/built-in.o: In function `rt5677_spi_driver_init':
:(.init.text+0x253c): undefined reference to `spi_register_driver'
This makes the SPI portion of the driver depend on the SPI subsystem,
and disables the function that uses SPI for firmware download if SPI
is disabled. The latter may not be the correct solution, but I could
not come up with a better one.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: af48f1d08a54741 ("ASoC: rt5677: Support DSP function for VAD application") Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function sst_acpi_probe() uses plain strcpy for setting member firmware_name
of a struct intel_sst_drv from member firmware of a struct sst_machines.
Thereby the destination array has got a length of 20 byte while the source may
hold 32 byte. Since eg. commit 64b9c90b8600 ("ASoC: Intel: Fix BYTCR firmware
name") increased strings from "fw_sst_0f28.bin" to "intel/fw_sst_0f28.bin"
there is an actual possibility that the 20 byte array at the end of struct
intel_sst_drv is overrun.
Thus increase the size of the destination and use the same define for both
structs. Detected by Coverity CID 1260087.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the image size would ever read as 0, pci_get_rom_size() could keep
processing the same image over and over again. Exit the loop if we ever
read a length of zero.
This fixes a soft lockup on boot when the radeon driver calls
pci_get_rom_size() on an AMD Radeon R7 250X PCIe discrete graphics card.
Some implementations of modprobe fail to load the driver for a PCI device
automatically because the "interface" part of the modalias from the kernel
is lowercase, and the modalias from file2alias is uppercase.
The "interface" is the low-order byte of the Class Code, defined in PCI
r3.0, Appendix D. Most interface types defined in the spec do not use
alpha characters, so they won't be affected. For example, 00h, 01h, 10h,
20h, etc. are unaffected.
Print the "interface" byte of the Class Code in uppercase hex, as we
already do for the Vendor ID, Device ID, Class, etc.
Commit 89ec3dcf17fd ("PCI: Generate uppercase hex for modalias interface
class") fixed only half of the problem. Some udev implementations rely on
the uevent file and not the modalias file.
d1c7e29e8d27 (HID: i2c-hid: prevent buffer overflow in early IRQ)
changed hid_get_input() to read ihid->bufsize bytes, which can be
more than wMaxInputLength. This is the case with the Dell XPS 13
9343, and it is causing events to be missed. In some cases the
missed events are releases, which can cause the cursor to jump or
freeze, among other problems. Limit the number of bytes read to
min(wMaxInputLength, ihid->bufsize) to prevent such problems.
Fixes: d1c7e29e8d27 "HID: i2c-hid: prevent buffer overflow in early IRQ" Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't really need to use different mac colors when adding mac
contexts, because they're not used anywhere. In fact, the firmware
doesn't accept 255 as a valid color, so we get into a SYSASSERT 0x3401
when we reach that.
Remove the color increment to use always zero and avoid reaching 255.
The base address of the scheduler in the device's memory
(SRAM) comes from two different sources. The periphery
register and the alive notification from the firmware.
We have a check in iwl_pcie_tx_start that ensures that
they are the same.
When we resume from WoWLAN, the firmware may have crashed
for whatever reason. In that case, the whole device may be
reset which means that the periphery register will hold a
meaningless value. When we come to compare
trans_pcie->scd_base_addr (which really holds the value we
had when we loaded the WoWLAN firmware upon suspend) and
the current value of the register, we don't see a match
unsurprisingly.
Trick the check to avoid a loud yet harmless WARN.
Note that when the WoWLAN has crashed, we will see that
in iwl_trans_pcie_d3_resume which will let the op_mode
know. Once the op_mode is informed that the WowLAN firmware
has crashed, it can't do much besides resetting the whole
device.
While debugging an issue with excessive softirq usage, I encountered the
following note in commit 3e339b5dae24a706 ("softirq: Use hotplug thread
infrastructure"):
[ paulmck: Call rcu_note_context_switch() with interrupts enabled. ]
...but despite this note, the patch still calls RCU with IRQs disabled.
This seemingly innocuous change caused a significant regression in softirq
CPU usage on the sending side of a large TCP transfer (~1 GB/s): when
introducing 0.01% packet loss, the softirq usage would jump to around 25%,
spiking as high as 50%. Before the change, the usage would never exceed 5%.
Moving the call to rcu_note_context_switch() after the cond_sched() call,
as it was originally before the hotplug patch, completely eliminated this
problem.
Signed-off-by: Calvin Owens <calvinowens@fb.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e9fd702a58c4 ("audit: convert audit watches to use fsnotify
instead of inotify") broke handling of renames in audit. Audit code
wants to update inode number of an inode corresponding to watched name
in a directory. When something gets renamed into a directory to a
watched name, inotify previously passed moved inode to audit code
however new fsnotify code passes directory inode where the change
happened. That confuses audit and it starts watching parent directory
instead of a file in a directory.
This can be observed for example by doing:
cd /tmp
touch foo bar
auditctl -w /tmp/foo
touch foo
mv bar foo
touch foo
and that's it - we see event for the first touch after creating the
audit rule, we see events for rename but we don't see any event for the
last touch. However we start seeing events for unrelated stuff
happening in /tmp.
Fix the problem by passing moved inode as data in the FS_MOVED_FROM and
FS_MOVED_TO events instead of the directory where the change happens.
This doesn't introduce any new problems because noone besides
audit_watch.c cares about the passed value:
fs/notify/fanotify/fanotify.c cares only about FSNOTIFY_EVENT_PATH events.
fs/notify/dnotify/dnotify.c doesn't care about passed 'data' value at all.
fs/notify/inotify/inotify_fsnotify.c uses 'data' only for FSNOTIFY_EVENT_PATH.
kernel/audit_tree.c doesn't care about passed 'data' at all.
kernel/audit_watch.c expects moved inode as 'data'.
Fixes: e9fd702a58c49db ("audit: convert audit watches to use fsnotify instead of inotify") Signed-off-by: Jan Kara <jack@suse.cz> Cc: Paul Moore <paul@paul-moore.com> Cc: Eric Paris <eparis@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 2d3d0c5 ("xfs: lobotomise xfs_trans_read_buf_map()") left
a landmine in the tracing code: trace_xfs_trans_buf_read() is now
call on all buffers that are read through this interface rather than
just buffers in transactions. For buffers outside transaction
context, bp->b_fspriv is null, and so the buf log item tracing
functions cannot be called. This causes a NULL pointer dereference
in the trace_xfs_trans_buf_read() function when tracing is turned
on.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the superblock is modified in a transaction, the commonly
modified fields are not actually copied to the superblock buffer to
avoid the buffer lock becoming a serialisation point. However, there
are some other operations that modify the superblock fields within
the transaction that don't directly log to the superblock but rely
on the changes to be applied during the transaction commit (to
minimise the buffer lock hold time).
When we do this, we fail to mark the buffer log item as being a
superblock buffer and that can lead to the buffer not being marked
with the corect type in the log and hence causing recovery issues.
Fix it by setting the type correctly, similar to xfs_mod_sb()...
Tested-by: Jan Kara <jack@suse.cz> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conversion from local to extent format does not set the buffer type
correctly on the new extent buffer when a symlink data is moved out
of line.
Fix the symlink code and leave a comment in the generic bmap code
reminding us that the format-specific data copy needs to set the
destination buffer type appropriately.
Tested-by: Jan Kara <jack@suse.cz> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that we set the type appropriately in both unlink list
addition and removal.
Tested-by: Jan Kara <jack@suse.cz> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara reported that log recovery was finding buffers with invalid
types in them. This should not happen, and indicates a bug in the
logging of buffers. To catch this, add asserts to the buffer
formatting code to ensure that the buffer type is in range when the
transaction is committed.
We don't set a type on buffers being marked stale - they are not
going to get replayed, the format item exists only for recovery to
be able to prevent replay of the buffer, so the type does not
matter. Hence that needs special casing here.
Reported-by: Jan Kara <jack@suse.cz> Tested-by: Jan Kara <jack@suse.cz> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was a bad typo in commit 43759d4f429c ("random: use an improved
fast_mix() function") and I didn't notice because it "looked right", so
I saw what I expected to see when I reviewed it.
Only months later did I look and notice it's not the Threefish-inspired
mix function that I had designed and optimized.
Mea Culpa. Each input bit still has a chance to affect each output bit,
and the fast pool is spilled *long* before it fills, so it's not a total
disaster, but it's definitely not the intended great improvement.
I'm still working on finding better rotation constants. These are good
enough, but since it's unrolled twice, it's possible to get better
mixing for free by using eight different constants rather than repeating
the same four.
Firmware for 04ca:2007 can be extracted from the latest Lenovo E145
Bluetooth driver for Windows (driver is however described as BCM20702
but contains also firwmare for BCM43142).
Search for BCM43142A0_001.001.011.0122.0153.hex within hex files, then
it must be converted using hex2hcd utility. Rename file to
BCM43142A0-04ca-2007.hcd, then move to /lib/firmware/brcm/.
Since this is an unsual USB vendor ID (0x19ff), these dongles are added
via USB_DEVICE macro and not USB_VENDOR_AND_INTERFACE_INFO as done for
mainstream Broadcom based dongles.
The latest known working firmware is BCM20702B0_002.001.014.0527.0557.hex
which needs to be converted using hex2hcd utility and then installed
as /lib/firmware/brcm/BCM20702A0-19ff-0239.hcd to make this device fully
operational.
However there are some flaws with this feature. The Set Event Mask Page 2
command is actually not supported and with that all connectionless slave
broadcast events are always enabled.
In addition the Synchronization Train Received event is actually broken
on this controller. It mixes up the order of parameters. According to the
Bluetooth Core specification the fields are like this:
According to the Bluetooth core specification valid identity addresses
are either Public Device Addresses or Static Random Addresses. IRKs
received with any other type of address should be discarded since we
cannot assume to know the permanent identity of the peer device.
This patch fixes a missing check for the Identity Address when receiving
the Identity Address Information SMP PDU.
BugLink: https://bugs.launchpad.net/bugs/1400215
ath3k devices fail to load firmwares on xHCI buses, but work well on
EHCI, this might be a compatibility issue between xHCI and ath3k chips.
As my testing result, those chips will work on xHCI buses again with
this patch.
This workaround is from Qualcomm, they also did some workarounds in
Windows driver.
Signed-off-by: Adam Lee <adam.lee@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of v3.18, ext4 started rejecting a remount which changes the
journal_checksum option.
Prior to that, it was simply ignored; the problem here is that
if someone has this in their fstab for the root fs, now the box
fails to boot properly, because remount of root with the new options
will fail, and the box proceeds with a readonly root.
I think it is a little nicer behavior to accept the option, but
warn that it's being ignored, rather than failing the mount,
but that might be a subjective matter...
Linus Torvalds [Mon, 9 Feb 2015 02:08:14 +0000 (18:08 -0800)]
Merge tag 'trace-fixes-v3.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace fixes from Steven Rostedt:
"During testing Sedat Dilek hit a "suspicious RCU usage" splat that
pointed out a real bug. During suspend and resume the tlb_flush
tracepoint is called when the CPU is going offline. As the CPU has
been noted as offline, RCU is ignoring that CPU, which means that it
can not use RCU protected locks. When tracepoints are activated, they
require RCU locking, and if RCU is ignoring a CPU that runs a
tracepoint, there is a chance that the tracepoint could cause
corruption.
The solution was to change the tracepoint into a
TRACE_EVENT_CONDITION() which allows us to check a condition to
determine if the tracepoint should be called or not. If the condition
is not met, the rcu protected code will not be executed. By adding
the condition "cpu_online(smp_processor_id())", this will prevent the
RCU protected code from being executed if the CPU is marked offline.
After adding this, another bug was discovered. As RCU checks rcu
callers, if a rcu call is not done, there is no check (obviously). We
found that tracepoints could be added in RCU ignored locations and not
have lockdep complain until the tracepoint is activated. This missed
places where tracepoints were added in places they should not have
been. To fix this, code was added in 3.18 that if lockdep is enabled,
any tracepoint will still call the rcu checks even if the tracepoint
is not enabled. The bug here, is that the check does not take the
CONDITION into account. As the condition may prevent tracepoints from
being activated in RCU ignored areas (as the one patch does), we get
false positives when we enable lockdep and hit a tracepoint that the
condition prevents it from being called in a RCU ignored location.
The fix for this is to add the CONDITION to the rcu checks, even if
the tracepoint is not enabled"
* tag 'trace-fixes-v3.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
x86/tlb/trace: Do not trace on CPU that is offline
tracing: Add condition check to RCU lockdep checks
x86/tlb/trace: Do not trace on CPU that is offline
When taking a CPU down for suspend and resume, a tracepoint may be called
when the CPU has been designated offline. As tracepoints require RCU for
protection, they must not be called if the current CPU is offline.
Unfortunately, trace_tlb_flush() is called in this scenario as was noted
by LOCKDEP:
...
Disabling non-boot CPUs ...
intel_pstate CPU 1 exiting
By converting the tlb_flush tracepoint to a TRACE_EVENT_CONDITION where the
condition is cpu_online(smp_processor_id()), we can avoid calling RCU protected
code when the CPU is offline.
Link: http://lkml.kernel.org/r/CA+icZUUGiGDoL5NU8RuxKzFjoLjEKRtUWx=JB8B9a0EQv-eGzQ@mail.gmail.com Cc: stable@vger.kernel.org # 3.17+ Fixes: d17d8f9dedb9 "x86/mm: Add tracepoints for TLB flushes" Reported-by: Sedat Dilek <sedat.dilek@gmail.com> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> Suggested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Dave Hansen <dave@sr71.net> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
tracing: Add condition check to RCU lockdep checks
The trace_tlb_flush() tracepoint can be called when a CPU is going offline.
When a CPU is offline, RCU is no longer watching that CPU and since the
tracepoint is protected by RCU, it must not be called. To prevent the
tlb_flush tracepoint from being called when the CPU is offline, it was
converted to a TRACE_EVENT_CONDITION where the condition checks if the
CPU is online before calling the tracepoint.
Unfortunately, this was not enough to stop lockdep from complaining about
it. Even though the RCU protected code of the tracepoint will never be
called, the condition is hidden within the tracepoint, and even though the
condition prevents RCU code from being called, the lockdep checks are
outside the tracepoint (this is to test tracepoints even when they are not
enabled).
Even though tracepoints should be checked to be RCU safe when they are not
enabled, the condition should still be considered when checking RCU.
Link: http://lkml.kernel.org/r/CA+icZUUGiGDoL5NU8RuxKzFjoLjEKRtUWx=JB8B9a0EQv-eGzQ@mail.gmail.com Fixes: 3a630178fd5f "tracing: generate RCU warnings even when tracepoints are disabled" Cc: stable@vger.kernel.org # 3.18+ Acked-by: Dave Hansen <dave@sr71.net> Reported-by: Sedat Dilek <sedat.dilek@gmail.com> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Linus Torvalds [Sat, 7 Feb 2015 19:10:40 +0000 (11:10 -0800)]
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull one more infiniband revert from Roland Dreier:
"One more last-second RDMA change for 3.19: Yann realized that the
previous revert of new userspace ABI did not go far enough, and we're
still exposing a change that we don't want. Revert even closer to
3.18 interface to make sure we get things right in the long run"
Yann Droneaud pipes up:
"I hope this could go in v3.19 as, at this stage, we don't want to
expose any bits of this ABI in a released kernel"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
Revert "IB/core: Add support for extended query device caps"
Linus Torvalds [Sat, 7 Feb 2015 19:04:48 +0000 (11:04 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"Forrest Liu tracked down a missing blk_finish_plug in the btrfs
logging code. This isn't a new bug, and it's hard to hit. But, it's
safe enough for inclusion now, and in my for-linus branch"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: add missing blk_finish_plug in btrfs_sync_log()
Linus Torvalds [Fri, 6 Feb 2015 21:56:02 +0000 (13:56 -0800)]
Merge branches 'timers-urgent-for-linus' and 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer and x86 fix from Ingo Molnar:
"A CLOCK_TAI early expiry fix and an x86 microcode driver oops fix"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hrtimer: Fix incorrect tai offset calculation for non high-res timer systems
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode: Return error from driver init code when loader is disabled
Linus Torvalds [Fri, 6 Feb 2015 21:34:26 +0000 (13:34 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Fix deadline parameter modification handling
sched/wait: Remove might_sleep() from wait_event_cmd()
sched: Fix crash if cpuset_cpumask_can_shrink() is passed an empty cpumask
sched/fair: Avoid using uninitialized variable in preferred_group_nid()
Linus Torvalds [Fri, 6 Feb 2015 20:50:37 +0000 (12:50 -0800)]
Merge tag 'sound-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Hopefully the final pull request for 3.19: this ended up with a
slightly higher volume than wished, but I put them all as they are
either stable or 3.19 regression fixes.
Most of commits are from ASoC, and have been stewed for a while in
linux-next. The only change in the common code is the regression
fixes for ASoC AC97 stuff wrt device registrations. The rest are
device-specific, mostly small fixes in various ASoC drivers and ak411x
on ice1724 boards"
* tag 'sound-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: Intel: fix sst firmware path for cht-bsw-rt5672
ARM: dts: Fix I2S1, I2S2 compatible for exynos4 SoCs
ASoC: sgtl5000: add delay before first I2C access
MAINTAINERS: ASoC: add maintainer for Intel BDW/HSW ASoC driver
ASoC: atmel_ssc_dai: fix the setting for DSP mode
ASoC: sgtl5000: Use shift mask when setting codec mode
ASoC: tlv320aic3x: Fix data delay configuration
ALSA: ak411x: Fix stall in work callback
ASoC: Intel: Used lock version to update shim registers
ASoC: wm8731: init mutex in i2c init path
ASoC: atmel_ssc_dai: fix start event for I2S mode
ASoC: rt5640: Add RT5642 ACPI ID for Intel Baytrail
ASoC: wm97xx: Reset AC'97 device before registering it
ASoC: Add support for allocating AC'97 device before registering it
Linus Torvalds [Fri, 6 Feb 2015 16:52:53 +0000 (08:52 -0800)]
Merge branch 'akpm' (patches from Andrew Morton)
Merge misc fixes from Andrew Morton:
"7 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/debug_pagealloc: fix build failure on ppc and some other archs
nilfs2: fix deadlock of segment constructor over I_SYNC flag
MAINTAINERS: remove SUPERH website
memcg, shmem: fix shmem migration to use lrucare
mm: export "high_memory" symbol on !MMU
.mailmap: update Konstantin Khlebnikov's email address
mm: pagewalk: call pte_hole() for VM_PFNMAP during walk_page_range
Yann Droneaud [Thu, 5 Feb 2015 21:10:18 +0000 (22:10 +0100)]
Revert "IB/core: Add support for extended query device caps"
While commit 7e36ef8205ff ("IB/core: Temporarily disable
ex_query_device uverb") is correct as it makes the extended
QUERY_DEVICE uverb (which came as part of commit 5a77abf9a97a
("IB/core: Add support for extended query device caps") and commit 860f10a799c8 ("IB/core: Add flags for on demand paging support")) not
available to userspace, it doesn't address the initial issue regarding
ib_copy_to_udata() [1][2].
Additionally, further discussions around this new uverb seems to
conclude it would require a different data structure than the one
currently described in <rdma/ib_user_verbs.h> [3].
Both of these issues require a revert of the changes, so this patch
partially reverts commit 8cdd312cfed7 ("IB/mlx5: Implement the ODP
capability query verb") and commit 860f10a799c8 ("IB/core: Add flags
for on demand paging support") and fully reverts commit 5a77abf9a97a
("IB/core: Add support for extended query device caps").
[1] "Re: [PATCH v3 06/17] IB/core: Add support for extended query device caps"
http://mid.gmane.org/1418733236.2779.26.camel@opteya.com
[3] "RE: [PATCH v1 1/5] IB/uverbs: ex_query_device: answer must not depend on request's comp_mask"
http://mid.gmane.org/2807E5FD2F6FDA4886F6618EAC48510E0CC12C30@CRSMSX101.amr.corp.intel.com
Cc: Eli Cohen <eli@mellanox.com> Cc: Haggai Eran <haggaie@mellanox.com> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Shachar Raindel <raindel@mellanox.com> Signed-off-by: Yann Droneaud <ydroneaud@opteya.com> Signed-off-by: Roland Dreier <roland@purestorage.com>
Joonsoo Kim [Thu, 5 Feb 2015 20:25:23 +0000 (12:25 -0800)]
mm/debug_pagealloc: fix build failure on ppc and some other archs
Kim Phillips reported following build failure.
LD init/built-in.o
mm/built-in.o: In function `free_pages_prepare':
mm/page_alloc.c:770: undefined reference to `.kernel_map_pages'
mm/built-in.o: In function `prep_new_page':
mm/page_alloc.c:933: undefined reference to `.kernel_map_pages'
mm/built-in.o: In function `map_pages':
mm/compaction.c:61: undefined reference to `.kernel_map_pages'
make: *** [vmlinux] Error 1
Reason for this problem is that commit 031bc5743f15
("mm/debug-pagealloc: make debug-pagealloc boottime configurable")
forgot to remove the old declaration of kernel_map_pages() for some
architectures. This patch removes them to fix build failure.
Reported-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: David Miller <davem@davemloft.net> Cc: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ryusuke Konishi [Thu, 5 Feb 2015 20:25:20 +0000 (12:25 -0800)]
nilfs2: fix deadlock of segment constructor over I_SYNC flag
Nilfs2 eventually hangs in a stress test with fsstress program. This
issue was caused by the following deadlock over I_SYNC flag between
nilfs_segctor_thread() and writeback_sb_inodes():
nilfs_segctor_thread()
nilfs_segctor_thread_construct()
nilfs_segctor_unlock()
nilfs_dispose_list()
iput()
iput_final()
evict()
inode_wait_for_writeback() * wait for I_SYNC flag
writeback_sb_inodes()
* set I_SYNC flag on inode->i_state
__writeback_single_inode()
do_writepages()
nilfs_writepages()
nilfs_construct_dsync_segment()
nilfs_segctor_sync()
* wait for completion of segment constructor
inode_sync_complete()
* clear I_SYNC flag after __writeback_single_inode() completed
writeback_sb_inodes() calls do_writepages() for dirty inodes after
setting I_SYNC flag on inode->i_state. do_writepages() in turn calls
nilfs_writepages(), which can run segment constructor and wait for its
completion. On the other hand, segment constructor calls iput(), which
can call evict() and wait for the I_SYNC flag on
inode_wait_for_writeback().
Since segment constructor doesn't know when I_SYNC will be set, it
cannot know whether iput() will block or not unless inode->i_nlink has a
non-zero count. We can prevent evict() from being called in iput() by
implementing sop->drop_inode(), but it's not preferable to leave inodes
with i_nlink == 0 for long periods because it even defers file
truncation and inode deallocation. So, this instead resolves the
deadlock by calling iput() asynchronously with a workqueue for inodes
with i_nlink == 0.
in mem_cgroup_migrate when shmem wants to replace a swap cache page
because of shmem_should_replace_page (the page is allocated from an
inappropriate zone). shmem_replace_page expects that the oldpage is not
on LRU list and calls mem_cgroup_migrate without lrucare. This is
obviously incorrect because swapcache pages might be on the LRU list
(e.g. swapin readahead page).
Fix this by enabling lrucare for the migration in shmem_replace_page.
Also clarify that lrucare should be used even if one of the pages might
be on LRU list.
The BUG_ON will trigger only when CONFIG_DEBUG_VM is enabled but even
without that the migration code might leave the old page on an
inappropriate memcg' LRU which is not that critical because the page
would get removed with its last reference but it is still confusing.
Fixes: 0a31bc97c80c ("mm: memcontrol: rewrite uncharge API") Signed-off-by: Michal Hocko <mhocko@suse.cz> Reported-by: Chris Wilson <chris@chris-wilson.co.uk> Reported-by: Dave Airlie <airlied@gmail.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: <stable@vger.kernel.org> [3.17+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Thu, 5 Feb 2015 20:25:12 +0000 (12:25 -0800)]
mm: export "high_memory" symbol on !MMU
The symbol 'high_memory' is provided on both MMU- and NOMMU-kernels, but
only one of them is exported, which leads to module build errors in
drivers that work fine built-in:
Shiraz Hashim [Thu, 5 Feb 2015 20:25:06 +0000 (12:25 -0800)]
mm: pagewalk: call pte_hole() for VM_PFNMAP during walk_page_range
walk_page_range() silently skips vma having VM_PFNMAP set, which leads
to undesirable behaviour at client end (who called walk_page_range).
Userspace applications get the wrong data, so the effect is like just
confusing users (if the applications just display the data) or sometimes
killing the processes (if the applications do something with
misunderstanding virtual addresses due to the wrong data.)
For example for pagemap_read, when no callbacks are called against
VM_PFNMAP vma, pagemap_read may prepare pagemap data for next virtual
address range at wrong index.
Eventually userspace may get wrong pagemap data for a task.
Corresponding to a VM_PFNMAP marked vma region, kernel may report
mappings from subsequent vma regions. User space in turn may account
more pages (than really are) to the task.
In my case I was using procmem, procrack (Android utility) which uses
pagemap interface to account RSS pages of a task. Due to this bug it
was giving a wrong picture for vmas (with VM_PFNMAP set).
Takashi Iwai [Thu, 5 Feb 2015 20:31:19 +0000 (21:31 +0100)]
Merge tag 'asoc-fix-ac97-v3.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: AC'97 fixes
These are rather too large for this late in the release cycle but
they're clear, well understood and have been tested to fix a regression
which was introduced for v3.19. The details are all in Lars' changelog
and they've been cooking in -next for a while, to a large extent out
of conservatism about the size.
Takashi Iwai [Thu, 5 Feb 2015 20:30:43 +0000 (21:30 +0100)]
Merge tag 'asoc-fix-intel-v3.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fix for Intel firmware name
Another one liner that arrived after the earlier pull request. There's
a trivial conflict with my -next branch, I'll send a pull request with
that resolution and some other new stuff before Monday.
Takashi Iwai [Thu, 5 Feb 2015 20:29:33 +0000 (21:29 +0100)]
Merge tag 'asoc-fix-v3.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.19
A few last minute fixes for v3.19, all driver specific. None of them
stand out particularly - it's all the standard people who are affected
will care stuff.
The Samsung fix is a DT only fix for the audio controller, it's being
merged via the ASoC tree due to process messups (the submitter sent it
at the end of a tangentally related series rather than separately to the
ARM folks) in order to make sure that it gets to people sooner.
Kevin Strasser [Thu, 5 Feb 2015 20:12:07 +0000 (12:12 -0800)]
ASoC: Intel: fix sst firmware path for cht-bsw-rt5672
All sst firmware is provided under the intel directory of the linux-firmware
tree. By default this directory structure is kept when installing on a target
system. Change the path to expect a default linux-firmware installation.
Signed-off-by: Kevin Strasser <kevin.strasser@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
1) Stretch ACKs can kill performance with Reno and CUBIC congestion
control, largely due to LRO and GRO. Fix from Neal Cardwell.
2) Fix userland breakage because we accidently emit zero length netlink
messages from the bridging code. From Roopa Prabhu.
3) Carry handling in generic csum_tcpudp_nofold is broken, fix from
Karl Beldan.
4) Remove bogus dev_set_net() calls from CAIF driver, from Nicolas
Dichtel.
5) Make sure PPP deflation never returns a length greater then the
output buffer, otherwise we overflow and trigger skb_over_panic().
Fix from Florian Westphal.
6) COSA driver needs VIRT_TO_BUS Kconfig dependencies, from Arnd
Bergmann.
7) Don't increase route cached MTU on datagram too big ICMPs. From Li
Wei.
8) Fix error path leaks in nf_tables, from Pablo Neira Ayuso.
9) Fix bitmask handling regression in netlink that broke things like
acpi userland tools. From Pablo Neira Ayuso.
10) Wrong header pointer passed to param_type2af() in SCTP code, from
Saran Maruti Ramanara.
11) Stacked vlans not handled correctly by vlan_get_protocol(), from
Toshiaki Makita.
12) Add missing DMA memory barrier to xgene driver, from Iyappan
Subramanian.
13) Fix crash in rate estimators, from Eric Dumazet.
14) We've been adding various workarounds, one after another, for the
change which added the per-net tcp_sock. It was meant to reduce
socket contention but added lots of problems.
Reduce this instead to a proper per-cpu socket and that rids us of
all the daemons.
From Eric Dumazet.
15) Fix memory corruption and OOPS in mlx4 driver, from Jack
Morgenstein.
16) When we disabled UFO in the virtio_net device, it introduces some
serious performance regressions. The orignal problem was IPV6
fragment ID generation, so fix that properly instead. From Vlad
Yasevich.
17) sr9700 driver build breaks on xtensa because it defines macros with
the same name as those used by the arch code. Use more unique
names. From Chen Gang.
18) Fix endianness in new virio 1.0 mode of the vhost net driver, from
Michael S Tsirkin.
19) Several sysctls were setting the maxlen attribute incorrectly, from
Sasha Levin.
20) Don't accept an FQ scheduler quantum of zero, that leads to crashes.
From Kenneth Klette Jonassen.
21) Fix dumping of non-existing actions in the packet scheduler
classifier. From Ignacy Gawędzki.
22) Return the write work_done value when doing TX work in the qlcnic
driver.
23) ip6gre_err accesses the info field with the wrong endianness, from
Sabrina Dubroca.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
sit: fix some __be16/u16 mismatches
ipv6: fix sparse errors in ip6_make_flowlabel()
net: remove some sparse warnings
flow_keys: n_proto type should be __be16
ip6_gre: fix endianness errors in ip6gre_err
qlcnic: Fix NAPI poll routine for Tx completion
amd-xgbe: Set RSS enablement based on hardware features
amd-xgbe: Adjust for zero-based traffic class count
cls_api.c: Fix dumping of non-existing actions' stats.
pkt_sched: fq: avoid hang when quantum 0
net: rds: use correct size for max unacked packets and bytes
vhost/net: fix up num_buffers endian-ness
gianfar: correct the bad expression while writing bit-pattern
net: usb: sr9700: Use 'SR_' prefix for the common register macros
Revert "drivers/net: Disable UFO through virtio"
Revert "drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets"
ipv6: Select fragment id during UFO segmentation if not set.
xen-netback: stop the guest rx thread after a fatal error
net/mlx4_core: Fix kernel Oops (mem corruption) when working with more than 80 VFs
isdn: off by one in connect_res()
...
Linus Torvalds [Thu, 5 Feb 2015 19:17:15 +0000 (11:17 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This patch set is fixing two serious problems which have turned up
late in the release cycle.
The first fixes a problem with 4k sector disks where the transfer
length (amount of data sent to the disk) was getting increased every
time the disk was revalidated leading to potential for overflows.
The other is a regression oops fix for some of our last merge window
code"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
sd: Fix max transfer length for 4k disks
scsi: fix device handler detach oops
Linus Torvalds [Thu, 5 Feb 2015 19:11:44 +0000 (11:11 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon and amdkfd fixes.
Radeon ones mostly for oops in some test/benchmark functions since
fencing changes, and one regression fix for old GPUs,
There is one cirrus regression fix, the 32bpp broke userspace, so this
hides it behind a module option for the few users who care.
I'm off for a few days, so this is probably the final pull I have, if
I see fixes from Intel I'll forward the pull as I should have email"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/cirrus: Limit modes depending on bpp option
drm/radeon: fix the crash in test functions
drm/radeon: fix the crash in benchmark functions
drm/radeon: properly set vm fragment size for TN/RL
drm/radeon: don't init gpuvm if accel is disabled (v3)
drm/radeon: fix PLLs on RS880 and older v2
drm/amdkfd: Don't create BUG due to incorrect user parameter
drm/amdkfd: max num of queues can't be 0
drm/amdkfd: Fix bug in accounting of queues
Linus Torvalds [Thu, 5 Feb 2015 19:07:25 +0000 (11:07 -0800)]
Merge tag 'spi-v3.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of driver specific fixes:
- Disable DMA mode for i.MX6DL chips due to a hardware bug.
- Don't use devm_kzalloc() outside of bind/unbind paths in the
fsl-dspi driver, fixing memory leaks"
* tag 'spi-v3.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: imx: use pio mode for i.mx6dl
spi: spi-fsl-dspi: Remove usage of devm_kzalloc
Linus Torvalds [Thu, 5 Feb 2015 18:57:29 +0000 (10:57 -0800)]
Merge tag 'pm+acpi-3.19-fin' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI power management fix from Rafael Wysocki:
"This is a revert of an ACPI Low-power Subsystem (LPSS) driver change
that was supposed to improve power management of the LPSS DMA
controller, but introduced more serious problems.
Since fixing them turns out to be non-trivial, it is better to revert
the commit in question at this point and try to fix the original issue
differently in the next cycle"
* tag 'pm+acpi-3.19-fin' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / LPSS: introduce a 'proxy' device to power on LPSS for DMA"
James Hogan [Mon, 19 Jan 2015 15:38:24 +0000 (15:38 +0000)]
IRQCHIP: mips-gic: Avoid rerouting timer IRQs for smp-cmp
Commit e9de688dac65 ("irqchip: mips-gic: Support local interrupts")
changed the GIC irqchip driver so that all local interrupts were routed
to the same CPU pin used for external interrupts. Unfortunately this
causes a regression when smp-cmp is used. The CPUs are started by the
bootloader and put in a timer based waiting poll loop, but when their
timer interrupts are rerouted to a different IRQ pin which is not
unmasked they never wake up.
Since smp-cmp support is deprecated and everybody who was using it
should be switching to smp-cps which brings up the secondary CPUs
without bootloader assistance, I've gone for the simple fix which can be
easily removed once smp-cmp is removed, rather than a fully generic fix.
In __gic_init() the local GIC_VPE_TIMER_MAP register is read to find the
boot-time routing of the local timer interrupt, and a chained handler is
added to that CPU pin as well as the normal one.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Fixes: e9de688dac65 ("irqchip: mips-gic: Support local interrupts") Cc: Andrew Bresticker <abrestic@chromium.org> Cc: Qais Yousef <qais.yousef@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Patchwork: https://patchwork.linux-mips.org/patch/9081/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Eric Dumazet [Wed, 4 Feb 2015 23:12:04 +0000 (15:12 -0800)]
sit: fix some __be16/u16 mismatches
Fixes following sparse warnings :
net/ipv6/sit.c:1509:32: warning: incorrect type in assignment (different base types)
net/ipv6/sit.c:1509:32: expected restricted __be16 [usertype] sport
net/ipv6/sit.c:1509:32: got unsigned short
net/ipv6/sit.c:1514:32: warning: incorrect type in assignment (different base types)
net/ipv6/sit.c:1514:32: expected restricted __be16 [usertype] dport
net/ipv6/sit.c:1514:32: got unsigned short
net/ipv6/sit.c:1711:38: warning: incorrect type in argument 3 (different base types)
net/ipv6/sit.c:1711:38: expected unsigned short [unsigned] [usertype] value
net/ipv6/sit.c:1711:38: got restricted __be16 [usertype] sport
net/ipv6/sit.c:1713:38: warning: incorrect type in argument 3 (different base types)
net/ipv6/sit.c:1713:38: expected unsigned short [unsigned] [usertype] value
net/ipv6/sit.c:1713:38: got restricted __be16 [usertype] dport
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 4 Feb 2015 23:03:25 +0000 (15:03 -0800)]
ipv6: fix sparse errors in ip6_make_flowlabel()
include/net/ipv6.h:713:22: warning: incorrect type in assignment (different base types)
include/net/ipv6.h:713:22: expected restricted __be32 [usertype] hash
include/net/ipv6.h:713:22: got unsigned int
include/net/ipv6.h:719:25: warning: restricted __be32 degrades to integer
include/net/ipv6.h:719:22: warning: invalid assignment: ^=
include/net/ipv6.h:719:22: left side has type restricted __be32
include/net/ipv6.h:719:22: right side has type unsigned int
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 4 Feb 2015 21:31:54 +0000 (13:31 -0800)]
flow_keys: n_proto type should be __be16
(struct flow_keys)->n_proto is in network order, use
proper type for this.
Fixes following sparse errors :
net/core/flow_dissector.c:139:39: warning: incorrect type in assignment (different base types)
net/core/flow_dissector.c:139:39: expected unsigned short [unsigned] [usertype] n_proto
net/core/flow_dissector.c:139:39: got restricted __be16 [assigned] [usertype] proto
net/core/flow_dissector.c:237:23: warning: incorrect type in assignment (different base types)
net/core/flow_dissector.c:237:23: expected unsigned short [unsigned] [usertype] n_proto
net/core/flow_dissector.c:237:23: got restricted __be16 [assigned] [usertype] proto
Signed-off-by: Eric Dumazet <edumazet@google.com> Fixes: e0f31d849867 ("flow_keys: Record IP layer protocol in skb_flow_dissect()") Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Wed, 4 Feb 2015 14:25:09 +0000 (15:25 +0100)]
ip6_gre: fix endianness errors in ip6gre_err
info is in network byte order, change it back to host byte order
before use. In particular, the current code sets the MTU of the tunnel
to a wrong (too big) value.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shahed Shaikh [Wed, 4 Feb 2015 10:41:25 +0000 (05:41 -0500)]
qlcnic: Fix NAPI poll routine for Tx completion
After d75b1ade567f ("net: less interrupt masking in NAPI")
driver's NAPI poll routine is expected to return
exact budget value if it wants to be re-called.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Fixes: d75b1ade567f ("net: less interrupt masking in NAPI") Signed-off-by: David S. Miller <davem@davemloft.net>
John Stultz [Thu, 5 Feb 2015 00:45:26 +0000 (16:45 -0800)]
hrtimer: Fix incorrect tai offset calculation for non high-res timer systems
I noticed some CLOCK_TAI timer test failures on one of my
less-frequently used configurations. And after digging in I
found in 76f4108892d9 (Cleanup hrtimer accessors to the
timekepeing state), the hrtimer_get_softirq_time tai offset
calucation was incorrectly rewritten, as the tai offset we
return shold be from CLOCK_MONOTONIC, and not CLOCK_REALTIME.
This results in CLOCK_TAI timers expiring early on non-highres
capable machines.
This patch fixes the issue, calculating the tai time properly
from the monotonic base.
projects / thirdparty / kernel / stable.git / log
