Support VF device IDs used by the Hyper-V hypervisor.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Reviewed-by: Andy Gospodarek <gospo@broadcom.com> Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The external module build shows the following warning if Module.symvers
is missing in the kernel tree.
WARNING: Symbol version dump "Module.symvers" is missing.
Modules may not have dependencies or modversions.
I think this is an important heads-up because the resulting modules may
not work as expected. This happens when you did not build the entire
kernel tree, for example, you might have prepared the minimal setups
for external modules by 'make defconfig && make modules_preapre'.
A problem is that 'make modules' creates Module.symvers even without
vmlinux. In this case, that warning is suppressed since Module.symvers
already exists in spite of its incomplete content.
The incomplete (i.e. invalid) Module.symvers should not be created.
This commit changes the second pass of modpost to dump symbols into
modules-only.symvers. The final Module.symvers is created by
concatenating vmlinux.symvers and modules-only.symvers if both exist.
Module.symvers is supposed to collect symbols from both vmlinux and
modules. It might be a bit confusing, and I am not quite sure if it
is an official interface, but presumably it is difficult to rename it
because some tools (e.g. kmod) parse it.
The mirror_gre_scale test creates as many ERSPAN sessions as the underlying
chip supports, and tests that they all work. In order to determine that it
issues a stream of ICMP packets and checks if they are mirrored as
expected.
However, the mausezahn invocation missed the -6 flag to identify the use of
IPv6 protocol, and was sending ICMP messages over IPv6, as opposed to
ICMP6. It also didn't pass an explicit source IP address, which apparently
worked at some point in the past, but does not anymore.
To fix these issues, extend the function mirror_test() in mirror_lib by
detecting the IPv6 protocol addresses, and using a different ICMP scheme.
Fix __mirror_gre_test() in the selftest itself to pass a source IP address.
Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The intention behind this test is to make sure that qdisc limit is
correctly projected to the HW. However, first, due to rounding in the
qdisc, and then in the driver, the number cannot actually be accurate. And
second, the approach to testing this is to oversubscribe the port with
traffic generated on the same switch. The actual backlog size therefore
fluctuates.
In practice, this test proved to be noisier than the rest, and spuriously
fails every now and then. Increase the tolerance to 10 % to avoid these
issues.
Signed-off-by: Petr Machata <petrm@nvidia.com> Acked-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The IOMMU table is divided into pools for concurrent mappings and each
pool has a separate spinlock. When taking the ownership of an IOMMU group
to pass through a device to a VM, we lock these spinlocks which triggers
a false negative warning in lockdep (below).
This fixes it by annotating the large pool's spinlock as a nest lock
which makes lockdep not complaining when locking nested locks if
the nest lock is locked already.
===
WARNING: possible recursive locking detected
5.11.0-le_syzkaller_a+fstn1 #100 Not tainted
--------------------------------------------
qemu-system-ppc/4129 is trying to acquire lock: c0000000119bddb0 (&(p->lock)/1){....}-{2:2}, at: iommu_take_ownership+0xac/0x1e0
but task is already holding lock: c0000000119bdd30 (&(p->lock)/1){....}-{2:2}, at: iommu_take_ownership+0xac/0x1e0
other info that might help us debug this:
Possible unsafe locking scenario:
Function qtnf_event_handle_external_auth calls memcpy without
checking the length.
A user could control that length and trigger a buffer overflow.
Fix by checking the length is within the maximum allowed size.
Fix the following out-of-bounds warnings by adding a new structure
wl3501_req instead of duplicating the same members in structure
wl3501_join_req and wl3501_scan_confirm:
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [39, 108] from the object at 'sig' is out of the bounds of referenced subobject 'beacon_period' with type 'short unsigned int' at offset 36 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [25, 95] from the object at 'sig' is out of the bounds of referenced subobject 'beacon_period' with type 'short unsigned int' at offset 22 [-Warray-bounds]
The problem is that the original code is trying to copy data into a
bunch of struct members adjacent to each other in a single call to
memcpy(). Now that a new struct wl3501_req enclosing all those adjacent
members is introduced, memcpy() doesn't overrun the length of
&sig.beacon_period and &this->bss_set[i].beacon_period, because the
address of the new struct object _req_ is used as the destination,
instead.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Fix the following out-of-bounds warnings by enclosing structure members
daddr and saddr into new struct addr, in structures wl3501_md_req and
wl3501_md_ind:
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [18, 23] from the object at 'sig' is out of the bounds of referenced subobject 'daddr' with type 'u8[6]' {aka 'unsigned char[6]'} at offset 11 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [18, 23] from the object at 'sig' is out of the bounds of referenced subobject 'daddr' with type 'u8[6]' {aka 'unsigned char[6]'} at offset 11 [-Warray-bounds]
The problem is that the original code is trying to copy data into a
couple of arrays adjacent to each other in a single call to memcpy().
Now that a new struct _addr_ enclosing those two adjacent arrays
is introduced, memcpy() doesn't overrun the length of &sig.daddr[0]
and &sig.daddr, because the address of the new struct object _addr_
is used, instead.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Free the SEV device if later initialization fails. The memory isn't
technically leaked as it's tracked in the top-level device's devres
list, but unless the top-level device is removed, the memory won't be
freed and is effectively leaked.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210406224952.4177376-2-seanjc@google.com> Reviewed-by: Brijesh Singh <brijesh.singh@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The buffer of SA bo will be used by many cases. So it's better
to invalidate the cache of indirect buffer allocated by SA before
commit the IB.
Signed-off-by: Jinzhou Su <Jinzhou.Su@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
the current implementation of hdcp2 rx id list validation does not
have handler/checker for invalid message status, e.g. HMAC, the V
parameter calculated from PSP not matching the V prime from Rx.
[how]
return a generic FAILURE for any message status not SUCCESS or
REVOKED.
[why]
During dsc enable, a divide by zero condition triggered the
kernel crash.
[how]
An IGT test, which enable the DSC, was crashing at the time of
restore the default dsc status, becaue of h_totals value
becoming 0. So add a check before divide condition. If h_total
is zero, gracefully ignore and set the default value.
Which happens because by the time we get to rtas_stop_self() we are
already offline. In addition the message can be spammy, and is not that
helpful for users, so remove it.
>From commit c0bbbdc32feb ("__netif_receive_skb_core: pass skb by
reference"), the first argument passed into __netif_receive_skb_core
has changed to reference of a skb pointer.
There is a reproducible sequence from the userland that will trigger a WARN_ON()
condition in taprio_get_start_time, which causes kernel to panic if configured
as "panic_on_warn". Catch this condition in parse_taprio_schedule to
prevent this condition.
Reported as bug on syzkaller:
https://syzkaller.appspot.com/bug?extid=d50710fd0873a9c6b40c
Reported-by: syzbot+d50710fd0873a9c6b40c@syzkaller.appspotmail.com Signed-off-by: Du Cheng <ducheng2@gmail.com> Acked-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
net/ethtool/ioctl.c:492:2: warning: 'memcpy' offset [49, 84] from the object at 'link_usettings' is out of the bounds of referenced subobject 'base' with type 'struct ethtool_link_settings' at offset 0 [-Warray-bounds]
The problem is that the original code is trying to copy data into a
some struct members adjacent to each other in a single call to
memcpy(). This causes a legitimate compiler warning because memcpy()
overruns the length of &link_usettings.base. Fix this by directly
using &link_usettings and _from_ as destination and source addresses,
instead.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109 Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ALC3263 codec on the XPS 13 9343 is also found on the Latitude 13 7350
and Venue 11 Pro 7140. They require the same handling for the combo jack to
work with a headset: GPIO pin 6 must be set.
The HDA driver always sets this pin on the ALC3263, which it distinguishes
by the codec vendor/device ID 0x10ec0288 and PCI subsystem vendor ID 0x1028
(Dell). The ASoC driver does not use PCI, so adapt this check to use DMI to
determine if Dell is the system vendor.
In case the frequency is invalid, ieee80211_parse_ch_switch_ie
will fail and we may not even reach the check in
ieee80211_sta_process_chanswitch. Drop the connection
in case ieee80211_parse_ch_switch_ie failed, but still
take into account the CSA mode to remember not to send
a deauth frame in case if it is forbidden to.
Linux network drivers normally disallow changing the MAC address when
the interface is up. This driver has been different in that it allows
to change the MAC address *only* when it's up. This patch brings
wilc1000 behavior more in line with other network drivers. We could
have replaced wilc_set_mac_addr() with eth_mac_addr() but that would
break existing documentation on how to change the MAC address.
Likewise, return -EADDRNOTAVAIL (not -EINVAL) when the specified MAC
address is invalid or unavailable.
Some of the per-CPU masks use cpu_cpu_mask as a filter to limit the search
for related CPUs. On a dlpar add of a CPU, update cpu_cpu_mask before
updating the per-CPU masks. This will ensure the cpu_cpu_mask is updated
correctly before its used in setting the masks. Setting the numa_node will
ensure that when cpu_cpu_mask() gets called, the correct node number is
used. This code movement helped fix the above call trace.
The 'chip_id' field of the XIVE CPU structure is used to choose a
target for a source located on the same chip. For that, the XIVE
driver queries the chip identifier from the "ibm,chip-id" property
and compares it to a 'src_chip' field identifying the chip of a
source. This information is only available on the PowerNV platform,
'src_chip' being assigned to XIVE_INVALID_CHIP_ID under pSeries.
The "ibm,chip-id" property is also not available on all platforms. It
was first introduced on PowerNV and later, under QEMU for pSeries/KVM.
However, the property is not part of PAPR and does not exist under
pSeries/PowerVM.
Assign 'chip_id' to XIVE_INVALID_CHIP_ID by default and let the
PowerNV platform override the value with the "ibm,chip-id" property.
net/core/flow_dissector.c:835:3: warning: 'memcpy' offset [33, 48] from the object at 'flow_keys' is out of the bounds of referenced subobject 'ipv6_src' with type '__u32[4]' {aka 'unsigned int[4]'} at offset 16 [-Warray-bounds]
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). So, the compiler legitimately complains about it. As these
are just a couple of members, fix this by copying each one of them in
separate calls to memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109 Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
net/sctp/sm_make_chunk.c:3150:4: warning: 'memcpy' offset [17, 28] from the object at 'addr' is out of the bounds of referenced subobject 'v4' with type 'struct sockaddr_in' at offset 0 [-Warray-bounds]
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109 Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by: Kees Cook <keescook@chromium.org> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When snd-hda-codec-hdmi is used with ASoC HDA controller like SOF (acomp
used for ELD notifications), display connection change done during suspend,
can be lost due to following sequence of events:
1. system in S3 suspend
2. DP/HDMI receiver connected
3. system resumed
4. HDA controller resumed, but card->deferred_resume_work not complete
5. acomp eld_notify callback
6. eld_notify ignored as power state is not CTL_POWER_D0
7. HDA resume deferred work completed, power state set to CTL_POWER_D0
This results in losing the notification, and the jack state reported to
user-space is not correct.
The check on step 6 was added in commit 8ae743e82f0b ("ALSA: hda - Skip
ELD notification during system suspend"). It would seem with the deferred
resume logic in ASoC core, this check is not safe.
Fix the issue by modifying the check to use "dev.power.power_state.event"
instead of ALSA specific card power state variable.
Lenovo Ideapad S740 requires quite a few COEF setups to make its
speakers working. The verb table was provided from Ryan Prescott as
the result of investigation via qemu:
https://github.com/ryanprescott/realtek-verb-tools/wiki/How-to-sniff-verbs-from-a-Windows-sound-driver
If the user selects the very first entry in a page and performs a
search-up operation, or selects the very last entry in a page and
performs a search-down operation that will not succeed (e.g., via
[/]asdfzzz[Up Arrow]), nconf will never terminate searching the page.
The reason is that in this case, the starting point will be set to -1
or n, which is then translated into (n - 1) (i.e., the last entry of
the page) or 0 (i.e., the first entry of the page) and finally the
search begins. This continues to work fine until the index reaches 0 or
(n - 1), at which point it will be decremented to -1 or incremented to
n, but not checked against the starting point right away. Instead, it's
wrapped around to the bottom or top again, after which the starting
point check occurs... and naturally fails.
My original implementation added another check for -1 before wrapping
the running index variable around, but Masahiro Yamada pointed out that
the actual issue is that the comparison point (starting point) exceeds
bounds (i.e., the [0,n-1] interval) in the first place and that,
instead, the starting point should be fixed.
This has the welcome side-effect of also fixing the case where the
starting point was n while searching down, which also lead to an
infinite loop.
OTOH, this code is now essentially all his work.
Amazingly, nobody seems to have been hit by this for 11 years - or at
the very least nobody bothered to debug and fix this.
selftests/bpf/Makefile includes lib.mk. With the following command
make -j60 LLVM=1 LLVM_IAS=1 <=== compile kernel
make -j60 -C tools/testing/selftests/bpf LLVM=1 LLVM_IAS=1 V=1
some files are still compiled with gcc. This patch
fixed lib.mk issue which sets CC to gcc in all cases.
[Why]
Underflow observed when disabling PIP overlay in-game when
vsync is disabled, due to OTC master lock not working with
game pipe which is immediate flip.
[How]
When performing a full update, override flip_immediate value
to false for all planes, so that flip occurs on vsync.
Signed-off-by: Anthony Wang <anthony1.wang@amd.com> Acked-by: Bindu Ramamurthy <bindur12@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In early AMD desktop/mobile platforms (during 2013), when the IOMMU
Performance Counter (PMC) support was first introduced in
commit 30861ddc9cca ("perf/x86/amd: Add IOMMU Performance Counter
resource management"), there was a HW bug where the counters could not
be accessed. The result was reading of the counter always return zero.
At the time, the suggested workaround was to add a test logic prior
to initializing the PMC feature to check if the counters can be programmed
and read back the same value. This has been working fine until the more
recent desktop/mobile platforms start enabling power gating for the PMC,
which prevents access to the counters. This results in the PMC support
being disabled unnecesarily.
Unfortunatly, there is no documentation of since which generation
of hardware the original PMC HW bug was fixed. Although, it was fixed
soon after the first introduction of the PMC. Base on this, we assume
that the buggy platforms are less likely to be in used, and it should
be relatively safe to remove this legacy logic.
The original commit tries to address an issue, where PMC power-gating
causing the IOMMU PMC pre-init test to fail on certain desktop/mobile
platforms where the power-gating is normally enabled.
There have been several reports that the workaround still does not
guarantee to work, and can add up to 100 ms (on the worst case)
to the boot process on certain platforms such as the MSI B350M MORTAR
with AMD Ryzen 3 2200G.
Therefore, revert this commit as a prelude to removing the pre-init
test.
Current rsnd needs to call .prepare (P) for clock settings,
.trigger for playback start (S) and stop (E).
It should be called as below from SSI point of view.
P -> S -> E -> P -> S -> E -> ...
But, if you used MIXer, below case might happen
(2)
1: P -> S ---> E -> ...
2: P ----> S -> ...
(1) (3)
P(1) setups clock, but E(2) resets it. and starts playback (3).
In such case, it will reports "SSI parent/child should use same rate".
rsnd_ssi_master_clk_start() which is the main function at (P)
was called from rsnd_ssi_init() (= S) before,
but was moved by below patch to rsnd_soc_dai_prepare() (= P) to avoid
using clk_get_rate() which shouldn't be used under atomic context.
commit 4d230d1271064 ("ASoC: rsnd: fixup not to call clk_get/set
under non-atomic")
Because of above patch, rsnd_ssi_master_clk_start() is now called at (P)
which is for non atomic context. But (P) is assuming that spin lock is
*not* used.
One issue now is rsnd_ssi_master_clk_start() is checking ssi->xxx
which should be protected by spin lock.
After above patch, adg.c had below patch for other reasons.
commit 06e8f5c842f2d ("ASoC: rsnd: don't call clk_get_rate()
under atomic context")
clk_get_rate() is used at probe() timing by this patch.
In other words, rsnd_ssi_master_clk_start() is no longer using
clk_get_rate() any more.
This means we can call it from rsnd_ssi_init() (= S) again which is
protected by spin lock.
This patch re-move it to under spin lock, and solves
1. checking ssi->xxx without spin lock issue.
2. clk setting / device start / device stop race condition.
Reported-by: Linh Phung T. Y. <linh.phung.jy@renesas.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/875z0x1jt5.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While removing large number of mappings from hash page tables for
large memory systems as soft-lockup is reported because of the time
spent inside htap_remove_mapping() like one below:
Fix this by adding a cond_resched() to the loop in
htap_remove_mapping() that issues hcall to remove hpte mapping. The
call to cond_resched() is issued every HZ jiffies which should prevent
the soft-lockup from being reported.
In case the device is stopped any usage of hw queues needs to be
reallocated in fw due to fw reset after device stop, so all driver
internal queue should also be freed, and if we don't free the next usage
would leak the old memory and get in recover flows
"iwlwifi 0000:00:03.0: dma_pool_destroy iwlwifi:bc" warning.
Also warn about trying to reuse an internal allocated queue.
If we (for example) have a trans_cfg entry in the PCI IDs table,
but then don't find a full cfg entry for it in the info table,
we fall through to the code that treats the PCI ID table entry
as a full cfg entry. This obviously causes crashes later, e.g.
when trying to build the firmware name string.
Avoid such crashes by using the low bit of the pointer as a tag
for trans_cfg entries (automatically using a macro that checks
the type when assigning) and then checking that before trying to
use the data as a full entry - if it's just a partial entry at
that point, fail.
Since we're adding some macro magic, also check that the type is
in fact either struct iwl_cfg_trans_params or struct iwl_cfg,
failing compilation ("initializer element is not constant") if
it isn't.
In fuse when a direct/write-through write happens we invalidate attrs
because that might have updated mtime/ctime on server and cached
mtime/ctime will be stale.
What about page writeback path. Looks like we don't invalidate attrs
there. To be consistent, invalidate attrs in writeback path as well. Only
exception is when writeback_cache is enabled. In that case we strust local
mtime/ctime and there is no need to invalidate attrs.
Recently users started experiencing failure of xfstests generic/080,
geneirc/215 and generic/614 on virtiofs. This happened only newer "stat"
utility and not older one. This patch fixes the issue.
So what's the root cause of the issue. Here is detailed explanation.
generic/080 test does mmap write to a file, closes the file and then checks
if mtime has been updated or not. When file is closed, it leads to
flushing of dirty pages (and that should update mtime/ctime on server).
But we did not explicitly invalidate attrs after writeback finished. Still
generic/080 passed so far and reason being that we invalidated atime in
fuse_readpages_end(). This is called in fuse_readahead() path and always
seems to trigger before mmaped write.
So after mmaped write when lstat() is called, it sees that atleast one of
the fields being asked for is invalid (atime) and that results in
generating GETATTR to server and mtime/ctime also get updated and test
passes.
But newer /usr/bin/stat seems to have moved to using statx() syscall now
(instead of using lstat()). And statx() allows it to query only ctime or
mtime (and not rest of the basic stat fields). That means when querying
for mtime, fuse_update_get_attr() sees that mtime is not invalid (only
atime is invalid). So it does not generate a new GETATTR and fill stat
with cached mtime/ctime. And that means updated mtime is not seen by
xfstest and tests start failing.
Invalidating attrs after writeback completion should solve this problem in
a generic manner.
Reset wifi subsystem when MCU is already running.
Fixes firmware download failure after soft reboot on systems where the PCIe
reset could not be performed properly.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Co-developed-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Deleting a key with the previous key index deletes the current key
Rework the code to better keep track of multiple keys and check for the
key index before deleting the current key
Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
As done for mt76_connac_mcu_alloc_wtbl_req, even if this is not a real
bug since mt7915_mcu_alloc_wtbl_req routine can fails just if nskb is NULL,
always check return value from mt7915_mcu_alloc_wtbl_req in order to avoid
possible future mistake.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
When operating two VAP on a MT7610 with encryption (PSK2, SAE, OWE),
only the first one to be created will transmit properly encrypteded
frames.
All subsequently created VAPs will sent out frames with the payload left
unencrypted, breaking multicast traffic (ICMP6 NDP) and potentially
disclosing information to a third party.
Disable GTK offloading and encrypt these frames in software to
circumvent this issue. THis only seems to be necessary on MT7610 chips,
as MT7612 is not affected from our testing.
Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
EEPROM blobs for MT7613BE radios start with (little endian) 0x7663,
which is also the PCI device ID for this device. The EEPROM is required
for the radio to work at useful power levels, otherwise only the lowest
power level is available.
Suggested-by: Georgi Vlaev <georgi.vlaev@konsulko.com> Tested-by: Stijn Segers <foss@volatilesystems.org> Signed-off-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
There were multiple issues in the current key set/remove code:
- deleting a key with the previous key index deletes the current key
- BIP key would only be uploaded correctly initially and corrupted on rekey
Rework the code to better keep track of multiple keys and check for the
key index before deleting the current key
Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix power tracking issue by replacing unnecessary IQ calibration
with LC calibration.
When thermal difference exceeds limitation, let RF circuit adjsut
its characteristic to fit in current environment.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210319054218.3319-6-pkshih@realtek.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The Special Function Registers on all Exynos SoC, including ARM64, are
32-bit wide, so entire driver uses matching functions like readl() or
writel(). On 64-bit ARM using unsigned long for register masks:
1. makes little sense as immediately after bitwise operation it will be
cast to 32-bit value when calling writel(),
2. is actually error-prone because it might promote other operands to
64-bit.
If panic_on_warn=1 is added in bootargs and compress offload playback with
DPCM is started, kernel panic would be occurred because rtd->card->pcm_mutex
isn't held in soc_compr_open_fe() and soc_compr_free_fe() and it generates
lockdep warning in the following code.
void snd_soc_runtime_action(struct snd_soc_pcm_runtime *rtd,
int stream, int action)
{
struct snd_soc_dai *dai;
int i;
lockdep_assert_held(&rtd->card->pcm_mutex);
To prevent lockdep warning but minimize side effect by adding mutex,
pcm_mutex is held just before snd_soc_runtime_activate() and
snd_soc_runtime_deactivate() and is released right after them.
After channel switch, we should consider any beacon with a
CSA IE as a new switch. If the CSA IE is a leftover from
before the switch that the AP forgot to remove, we'll get
a CSA-to-Self.
This caused issues in iwlwifi where the firmware saw a beacon
with a CSA-to-Self with mode = 1 on the new channel after a
switch. The firmware considered this a new switch and closed
its queues. Since the beacon didn't change between before and
after the switch, we wouldn't handle it (the CRC is the same)
and we wouldn't let the firmware open its queues again or
disconnect if the CSA IE stays for too long.
Clear the CRC valid state after we switch to make sure that
we handle the beacon and handle the CSA IE as required.
Some drivers, for example mt76, use the skb priority field, and
expects that to be consistent with the skb queue mapping. On some
frame injection code paths that was not true, and it broke frame
injection. Now the skb queue mapping is set according to the skb
priority value when the frame is injected. The skb priority value
is also derived from the frame data for all frame types, as it
was done prior to commit dbd50a851c50 (only allocate one queue
when using iTXQs). Fixes frame injection with the mt76 driver on
MT7610E chipset.
If a graph node is not found for a given node, of_get_next_endpoint()
will emit the following error message :
OF: graph: no port node found in /<node_name>
If the given component doesn't have any explicit connections (e.g,
ETE) we could simply ignore the graph parsing. As for any legacy
component where this is mandatory, the device will not be usable
as before this patch. Updating the DT bindings to Yaml and enabling
the schema checks can detect such issues with the DT.
Cc: Mike Leach <mike.leach@linaro.org> Cc: Leo Yan <leo.yan@linaro.org> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20210405164307.1720226-11-suzuki.poulose@arm.com Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Loongson64 processors have a writecombine issue that maybe failed to
write back framebuffer used with ATI Radeon or AMD GPU at times, after
commit 8a08e50cee66 ("drm: Permit video-buffers writecombine mapping
for MIPS"), there exists some errors such as blurred screen and lockup,
and so on.
[ 60.958721] radeon 0000:03:00.0: ring 0 stalled for more than 10079msec
[ 60.965315] radeon 0000:03:00.0: GPU lockup (current fence id 0x0000000000000112 last fence id 0x000000000000011d on ring 0)
[ 60.976525] radeon 0000:03:00.0: ring 3 stalled for more than 10086msec
[ 60.983156] radeon 0000:03:00.0: GPU lockup (current fence id 0x0000000000000374 last fence id 0x00000000000003a8 on ring 3)
As discussed earlier [1], it might be better to disable writecombine
on the CPU detection side because the root cause is unknown now.
Actually, this patch is a temporary solution to just make it work well,
it is not a proper and final solution, I hope someone will have a better
solution to fix this issue in the future.
We set hdev->cur_adv_instance in the adv param MGMT request to allow the
callback to the hci param request to set the tx power to the correct
instance. Now that the callbacks use the advertising handle from the hci
request (as they should), this workaround is no longer necessary.
Furthermore, this change resolves a race condition that is more
prevalent when using the extended advertising MGMT calls - if
hdev->cur_adv_instance is set in the params request, then when the data
request is called, we believe our new instance is already active. This
treats it as an update and immediately schedules the instance with the
controller, which has a potential race with the software rotation adv
update. By not setting hdev->cur_adv_instance too early, the new
instance is queued as it should be, to be used when the rotation comes
around again.
This change is tested on harrison peak to confirm that it resolves the
race condition on registration, and that there is no regression in
single- and multi-advertising automated tests.
'mptcp_connect' already has a timeout for poll() but in some cases, it
is not enough.
With "timeout" tool, we will force the command to fail if it doesn't
finish on time. Thanks to that, the script will continue and display
details about the current state before marking the test as failed.
Displaying this state is very important to be able to understand the
issue. Best to have our CI reporting the issue than just "the test
hanged".
Note that in mptcp_connect.sh, we were using a long timeout to validate
the fact we cannot create a socket if a sysctl is set. We don't need
this timeout.
In diag.sh, we want to send signals to mptcp_connect instances that have
been started in the netns. But we cannot send this signal to 'timeout'
otherwise that will stop the timeout and messages telling us SIGUSR1 has
been received will be printed. Instead of trying to find the right PID
and storing them in an array, we can simply use the output of
'ip netns pids' which is all the PIDs we want to send signal to.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/160 Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a quirk with the jack-detect and dmic settings necessary to make
jack-detect and the builtin mic work on Dell Venue 10 Pro 5055 tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20210402140747.174716-5-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is an issue when the Tx or Rx ring size increases using
'ethtool -L ...' where the new rings don't get the correct ITR
values because when we rebuild the VSI we don't know that some
of the rings may be new.
Fix this by looking at the original number of rings and
determining if the rings in ice_vsi_rebuild_set_coalesce()
were not present in the original rings received in
ice_vsi_rebuild_get_coalesce().
Also change the code to return an error if we can't allocate
memory for the coalesce data in ice_vsi_rebuild().
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Chuwi Hi8 tablet is using an analog mic on IN1 and has its
jack-detect connected to JD2_IN4N, instead of using the default
IN3 for its internal mic and JD1_IN4P for jack-detect.
It also only has 1 speaker.
Add a quirk applying the correct settings for this configuration.
Currently hns3 driver only handle the xmit skb with one level of
fraglist skb, add handling for multi level by calling hns3_tx_bd_num()
recursively when calculating bd num and calling hns3_fill_skb_to_desc()
recursively when filling tx desc.
When the skb has a fraglist level of 24, the skb is simply dropped and
stats.max_recursion_level is added to record the error. Move the stat
handling from hns3_nic_net_xmit() to hns3_nic_maybe_stop_tx() in order
to handle different error stat and add the 'max_recursion_level' and
'hw_limitation' stat.
Note that the max recursive level as 24 is chose according to below:
commit 48a1df65334b ("skbuff: return -EMSGSIZE in skb_to_sgvec to
prevent overflow").
And that we are not able to find a testcase to verify the recursive
fraglist case, so Fixes tag is not provided.
Reported-by: Barry Song <song.bao.hua@hisilicon.com> Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The array size of bd_num_list is a fixed value, it may have potential
overflow risk when array size of hclge_dfx_bd_offset_list is greater
than that fixed value. So modify bd_num_list as a pointer and allocate
memory for it according to array size of hclge_dfx_bd_offset_list.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The check of the emergency context initialisation in
vmap_stack_overflow is buggy for the SMP case, as it
compares r1 with 0 while in the SMP case r1 is offseted
by the CPU id.
Instead of fixing it, just perform static initialisation
of the first emergency context.
The rfi_flush and entry_flush selftests work by using the PM_LD_MISS_L1
perf event to count L1D misses. The value of this event has changed
over time:
- Power7 uses 0x400f0
- Power8 and Power9 use both 0x400f0 and 0x3e054
- Power10 uses only 0x3e054
Rather than relying on raw values, configure perf to count L1D read
misses in the most explicit way available.
This fixes the selftests to work on systems without 0x400f0 as
PM_LD_MISS_L1, and should change no behaviour for systems that the tests
already worked on.
The only potential downside is that referring to a specific perf event
requires PMU support implemented in the kernel for that platform.
There is a possibility of receiving a zapped sock on
l2cap_sock_connect(). This could lead to interesting crashes, one
such case is tearing down an already tore l2cap_sock as is happened
with this call trace:
Recently we had an interop issue where RARP packets got suppressed with
bridge neigh suppression enabled, but the check in the code was meant to
suppress GARP. Exclude RARP packets from it which would allow some VMWare
setups to work, to quote the report:
"Those RARP packets usually get generated by vMware to notify physical
switches when vMotion occurs. vMware may use random sip/tip or just use
sip=tip=0. So the RARP packet sometimes get properly flooded by the vtep
and other times get dropped by the logic"
Reported-by: Amer Abdalamer <amer@nvidia.com> Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
net/sched/cls_flower.c:214:20: warning: cast from restricted __be16
net/sched/cls_flower.c:214:20: warning: incorrect type in argument 1 (different base types)
net/sched/cls_flower.c:214:20: expected unsigned short [usertype] val
net/sched/cls_flower.c:214:20: got restricted __be16 [usertype] dst
This is because we use htons on struct flow_dissector_key_ports members
src and dst, which are defined as __be16, so they are already in network
byte order, not host. The byte swap function for the other direction
should have been used.
Because htons and ntohs do the same thing (either both swap, or none
does), this change has no functional effect except to silence the
warnings.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot is hitting "INFO: trying to register non-static key." message [1],
for "struct l2cap_chan"->tx_q.lock spinlock is not yet initialized when
l2cap_chan_del() is called due to e.g. timeout.
Since "struct l2cap_chan"->lock mutex is initialized at l2cap_chan_create()
immediately after "struct l2cap_chan" is allocated using kzalloc(), let's
as well initialize "struct l2cap_chan"->{tx_q,srej_q}.lock spinlocks there.
Currently l2cap_chan_set_defaults() reset chan->conf_state to zero.
However, there is a flag CONF_NOT_COMPLETE which is set when
creating the l2cap_chan. It is suggested that the flag should be
cleared when l2cap_chan is ready, but when l2cap_chan_set_defaults()
is called, l2cap_chan is not yet ready. Therefore, we must set this
flag as the default.
Current implementation of bebob driver doesn't correctly handle the case
that the device has multiple MIDI ports. The cause is the number of MIDI
conformant data channels is passed to AM824 data block processing layer.
The buggy parameters currently get caught later, but emit a noisy WARN.
Userspace should not be able to trigger this, so add similar checks much
earlier. Also avoids some unneeded code paths, of course. Apply kernel
coding stlye to a comment while here.
Reported-by: syzbot+ffb0b3ffa6cfbc7d7b3f@syzkaller.appspotmail.com Tested-by: syzbot+ffb0b3ffa6cfbc7d7b3f@syzkaller.appspotmail.com Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
snd_pcm_hw_params_set_rate_near can return incorrect sample rate in
some cases, e.g. when the backend output rate is set to some value higher
than 48000 Hz and the input rate is 8000 Hz. So passing the value returned
by snd_pcm_hw_params_set_rate_near to snd_pcm_hw_params will result in
"FSO/FSI ratio error" and playing no audio at all while the userland
is not properly notified about the issue.
If SRC is unable to convert the requested sample rate to the sample rate
the backend is using, then the requested sample rate should be adjusted in
rsnd_hw_params. The userland will be notified about that change in the
returned hw_params structure.
Commit eaf4fac47807 ("net: stmmac: Do not accept invalid MTU values")
started using the TX FIFO size to verify what counts as a valid MTU
request for the stmmac driver. This is unset for the ipq806x variant.
Looking at older patches for this it seems the RX + TXs buffers can be
up to 8k, so set appropriately.
(I sent this as an RFC patch in June last year, but received no replies.
I've been running with this on my hardware (a MikroTik RB3011) since
then with larger MTUs to support both the internal qca8k switch and
VLANs with no problems. Without the patch it's impossible to set the
larger MTU required to support this.)
Signed-off-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit e20f0dbf204f ("net/mlx5e: RX, Add a prefetch command for small
L1_CACHE_BYTES") switched to using net_prefetchw at all places in mlx5e.
In the same time frame, commit 5af75c747e2a ("net/mlx5e: Enhanced TX
MPWQE for SKBs") added one more usage of prefetchw. When these two
changes were merged, this new occurrence of prefetchw wasn't replaced
with net_prefetchw.
This commit fixes this last occurrence of prefetchw in
mlx5e_tx_mpwqe_session_start, making the same change that was done in
mlx5e_xdp_mpwqe_session_start.
The Asus T100TAF uses the same jack-detect settings as the T100TA,
this has been confirmed on actual hardware.
Add these settings to the T100TAF quirks to enable jack-detect support
on the T100TAF.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20210312114850.13832-1-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
(struct tipc_link_info)->dest is in network order (__be32), so we must
convert the value to network order before assigning. The problem detected
by sparse:
net/tipc/netlink_compat.c:699:24: warning: incorrect type in assignment (different base types)
net/tipc/netlink_compat.c:699:24: expected restricted __be32 [usertype] dest
net/tipc/netlink_compat.c:699:24: got int
Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes issues which occurs when dlm lowcomms synchronize their
workqueues but dlm application layer already released the lockspace. In
such cases messages like:
dlm: gfs2: release_lockspace final free
dlm: invalid lockspace 3841231384 from 1 cmd 1 type 11
are printed on the kernel log. This patch is solving this issue by
introducing a new "shutdown" hook before calling "stop" hook when the
lockspace is going to be released finally. This should pretend any
dlm messages sitting in the workqueues during or after lockspace
removal.
It's necessary to call dlm_scand_stop() as I instrumented
dlm_lowcomms_get_buffer() code to report a warning after it's called after
dlm_midcomms_shutdown() functionality, see below:
This patch fixes the flushing of send work before shutdown. The function
cancel_work_sync() is not the right workqueue functionality to use here
as it would cancel the work if the work queues itself. In cases of
EAGAIN in send() for dlm message we need to be sure that everything is
send out before. The function flush_work() will ensure that every send
work is be done inclusive in EAGAIN cases.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds an additional check for minimum dlm header size which is
an invalid dlm message and signals a broken stream. A msglen field cannot
be less than the dlm header size because the field is inclusive header
lengths.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While running tcpkill I experienced invalid header length values while
receiving to check that a node doesn't try to send a invalid dlm message
we also check on applications minimum allocation limit. Also use
DEFAULT_BUFFER_SIZE as maximum allocation limit. The define
LOWCOMMS_MAX_TX_BUFFER_LEN is to calculate maximum buffer limits on
application layer, future midcomms layer will subtract their needs from
this define.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds checks for dlm config attributes regarding to protocol
parameters as it makes only sense to change them when dlm is not running.
It also adds a check for valid protocol specifiers and return invalid
argument if they are not supported.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes an deadlock issue when dlm_lowcomms_close() is called.
When dlm_lowcomms_close() is called the clusters_root.subsys.su_mutex is
held to remove configfs items. At this time we flushing (e.g.
cancel_work_sync()) the workers of send and recv workqueue. Due the fact
that we accessing configfs items (mark values), these workers will lock
clusters_root.subsys.su_mutex as well which are already hold by
dlm_lowcomms_close() and ends in a deadlock situation.
[67170.703046] ======================================================
[67170.703965] WARNING: possible circular locking dependency detected
[67170.704758] 5.11.0-rc4+ #22 Tainted: G W
[67170.705433] ------------------------------------------------------
[67170.706228] dlm_controld/280 is trying to acquire lock:
[67170.706915] ffff9f2f475a6948 ((wq_completion)dlm_recv){+.+.}-{0:0}, at: __flush_work+0x203/0x4c0
[67170.708026]
but task is already holding lock:
[67170.708758] ffffffffa132f878 (&clusters_root.subsys.su_mutex){+.+.}-{3:3}, at: configfs_rmdir+0x29b/0x310
[67170.710016]
which lock already depends on the new lock.
The new behaviour adds the mark value to the node address configuration
which doesn't require to held the clusters_root.subsys.su_mutex by
accessing mark values in a separate datastructure. However the mark
values can be set now only after a node address was set which is the
case when the user is using dlm_controld.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes the following message which randomly pops up during
glocktop call:
seq_file: buggy .next function table_seq_next did not update position index
The issue is that seq_read_iter() in fs/seq_file.c also needs an
increment of the index in an non next record case as well which this
patch fixes otherwise seq_read_iter() will print out the above message.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Declare the Pioneer DJM-850 interfaces for capture and playback.
See https://github.com/nm2107/Pioneer-DJM-850-driver-reverse-engineering/blob/172fb9a61055960c88c67b7c416fe5bf3609807b/doc/usb-device-specifications.md
for the complete device spec.
When growing halt-polling, there is no check that the poll time exceeds
the per-VM limit. It's possible for vcpu->halt_poll_ns to grow past
kvm->max_halt_poll_ns and stay there until a halt which takes longer
than kvm->halt_poll_ns.
Signed-off-by: David Matlack <dmatlack@google.com> Signed-off-by: Venkatesh Srinivas <venkateshs@chromium.org>
Message-Id: <20210506152442.4010298-1-venkateshs@chromium.org> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that there are systems where HWP is enabled during
initialization by the platform firmware (BIOS), but HWP EPP support
is not advertised.
After commit 7aa1031223bc ("cpufreq: intel_pstate: Avoid enabling HWP
if EPP is not supported") intel_pstate refuses to use HWP on those
systems, but the fallback PERF_CTL interface does not work on them
either because of enabled HWP, and once enabled, HWP cannot be
disabled. Consequently, the users of those systems cannot control
CPU performance scaling.
Address this issue by making intel_pstate use HWP unconditionally if
it is enabled already when the driver starts.
Fixes: 7aa1031223bc ("cpufreq: intel_pstate: Avoid enabling HWP if EPP is not supported") Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: 5.9+ <stable@vger.kernel.org> # 5.9+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As pm_runtime_need_not_resume() relies also on usage_count, it can return
a different value in pm_runtime_force_suspend() compared to when called in
pm_runtime_force_resume(). Different return values can happen if anything
calls PM runtime functions in between, and causes the parent child_count
to increase on every resume.
So far I've seen the issue only for omapdrm that does complicated things
with PM runtime calls during system suspend for legacy reasons:
omap_atomic_commit_tail() for omapdrm.0
dispc_runtime_get()
wakes up 58000000.dss as it's the dispc parent
dispc_runtime_resume()
rpm_resume() increases parent child_count
dispc_runtime_put() won't idle, PM runtime suspend blocked
pm_runtime_force_suspend() for 58000000.dss, !pm_runtime_need_not_resume()
__update_runtime_status()
system suspended
pm_runtime_force_resume() for 58000000.dss, pm_runtime_need_not_resume()
pm_runtime_enable() only called because of pm_runtime_need_not_resume()
omap_atomic_commit_tail() for omapdrm.0
dispc_runtime_get()
wakes up 58000000.dss as it's the dispc parent
dispc_runtime_resume()
rpm_resume() increases parent child_count
dispc_runtime_put() won't idle, PM runtime suspend blocked
...
rpm_suspend for 58000000.dss but parent child_count is now unbalanced
Let's fix the issue by adding a flag for needs_force_resume and use it in
pm_runtime_force_resume() instead of pm_runtime_need_not_resume().
Additionally omapdrm system suspend could be simplified later on to avoid
lots of unnecessary PM runtime calls and the complexity it adds. The
driver can just use internal functions that are shared between the PM
runtime and system suspend related functions.
Fixes: 4918e1f87c5f ("PM / runtime: Rework pm_runtime_force_suspend/resume()") Signed-off-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Cc: 4.16+ <stable@vger.kernel.org> # 4.16+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In VMX, the host NMI handler needs to be invoked after NMI VM-Exit.
Before commit 1a5488ef0dcf6 ("KVM: VMX: Invoke NMI handler via indirect
call instead of INTn"), this was done by INTn ("int $2"). But INTn
microcode is relatively expensive, so the commit reworked NMI VM-Exit
handling to invoke the kernel handler by function call.
But this missed a detail. The NMI entry point for direct invocation is
fetched from the IDT table and called on the kernel stack. But on 64-bit
the NMI entry installed in the IDT expects to be invoked on the IST stack.
It relies on the "NMI executing" variable on the IST stack to work
correctly, which is at a fixed position in the IST stack. When the entry
point is unexpectedly called on the kernel stack, the RSP-addressed "NMI
executing" variable is obviously also on the kernel stack and is
"uninitialized" and can cause the NMI entry code to run in the wrong way.
Provide a non-ist entry point for VMX which shares the C-function with
the regular NMI entry and invoke the new asm entry point instead.
On 32-bit this just maps to the regular NMI entry point as 32-bit has no
ISTs and is not affected.
[ tglx: Made it independent for backporting, massaged changelog ]
Fixes: 1a5488ef0dcf6 ("KVM: VMX: Invoke NMI handler via indirect call instead of INTn") Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Lai Jiangshan <laijs@linux.alibaba.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/87r1imi8i1.ffs@nanos.tec.linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
