Remove the ephy-pins from the ethernet device tree node. The ephy-pins
are useed to controll the ePHY LEDs and this board doesn't have these.
Instead one of the ePHY pins is used in GPIO mode to control the WAN
LED.
Use the switch LED trigger to control the WAN LED. Move the power LED
handling to diag.sh to show the boot status via this LED.
Add the missing kernel packages for USB and microSD card reader to the
default package selection.
Fix the maximum image size value. The board has a 32MByte flash chip.
Fixes: FS#1055 Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
[make the commit message more verbose, remove GPIO pinmux for pins not
used as GPIOs] Signed-off-by: Mathias Kresin <dev@kresin.me>
Alex Maclean [Mon, 23 Oct 2017 12:48:19 +0000 (13:48 +0100)]
tools/squashfs4: include sysmacros.h explicitly
glibc is moving to remove the include of sys/sysmacros.h from
sys/types.h, and some distros have done this early. Other libcs may
already lack this include. Include sysmacros.h explicitly.
Alex Maclean [Mon, 23 Oct 2017 12:47:55 +0000 (13:47 +0100)]
tools/squashfs: include sysmacros.h explicitly
glibc is moving to remove the include of sys/sysmacros.h from
sys/types.h, and some distros have done this early. Other libcs may
already lack this include. Include sysmacros.h explicitly.
Fixes: FS#1018 Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Alex Maclean [Mon, 23 Oct 2017 12:47:33 +0000 (13:47 +0100)]
tools/mtd-utils: include sysmacros.h explicitly
glibc is moving to remove the include of sys/sysmacros.h from
sys/types.h, and some distros have done this early. Other libcs may
already lack this include. Include sysmacros.h explicitly.
Alex Maclean [Mon, 23 Oct 2017 12:43:43 +0000 (13:43 +0100)]
tools/findutils: include sysmacros.h explicitly
glibc is moving to remove the include of sys/sysmacros.h from
sys/types.h, and some distros have done this early. Other libcs may
already lack this include. Include sysmacros.h explicitly.
Fixes: FS#1016 Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Rosen Penev [Tue, 17 Oct 2017 16:28:39 +0000 (09:28 -0700)]
mdadm: Fix config generation
The init script generated something like "DEVICE=/dev/sda" when it should
have been generating "DEVICE /dev/sda". mdadm errors on this. Patch by jow.
Also changed the default sendmail path to /usr/sbin/sendmail. No package
in LEDE provides /sbin/sendmail. msmtp provides /usr/sbin/sendmail so use
that.
Also add a patch to fix file paths for mdadm runtime files. mdadm currently
errors on them since /run is missing. Once /run is added to stock LEDE, this
patch can be removed.
The package kmod-ipt-debug builds the module xt_TRACE, which allows
users to use '-j TRACE' as target in the chain PREROUTING of the table
raw in iptables.
The kernel compilation flag NETFILTER_XT_TARGET_TRACE is also enabled so
that this feature which is implemented deep inside the linux IP stack
(for example in sk_buff) is compiled.
But a strace of iptables -t raw -I PREROUTING -p icmp -j TRACE reveals
that an attempt is made to read /usr/lib/iptables/libxt_TRACE.so, which
fails as this dynamic library is not present on the system.
I created the package iptables-mod-trace which takes care of that, and
target TRACE now works!
Signed-off-by: Martin Wetterwald <martin.wetterwald@corp.ovh.com>
[Jo-Philipp Wich: also remove trace extension from builtin extension list
and depend on kmod-ipt-raw since its required for rules] Signed-off-by: Jo-Philipp Wich <jo@mein.io> Tested-by: Enrico Mioso <mrkiko.rs@gmail.com>
Jonas Gorski [Fri, 13 Oct 2017 12:21:53 +0000 (14:21 +0200)]
treewide: do not use IMG_PREFIX in Image/Prepare
IMG_PREFIX can be modified in ImageBuilder by passing EXTRA_IMAGE_NAME
on command line, but Image/Prepare is not run in ImageBuilder. This
causes missing files when IMG_PREFIX is used for target file names in
Image/Prepare, then as source file names in Image/BuildKernel or
Image/Build.
Fix this by using a fixed output file name in Image/Prepare, and copy to
the expected file name in Image/BuildKernel instead, which is run by
ImageBuilder.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tolga Cakir [Tue, 24 Oct 2017 20:03:33 +0000 (22:03 +0200)]
ipq806x: fix Zyxel NBG6817 WiFi button
Zyxel NBG6817 features a WiFi button, which becomes functional by setting
correct GPIO. It is a switch-type button, so it emits KEY_RFKILL on each ON
and OFF state. This is achieved by setting input-type to EV_SW.
Mathias Kresin [Mon, 15 May 2017 21:59:25 +0000 (23:59 +0200)]
mpc85xx: use the generic board detect
Use the values populated by the generic board detect function. The
first compatible from the device tree source file will be the board
name in userspace. The model property from the device tree source file
will be the model name.
Change the board name where used in the userspace and drop the target
specific board detect, to use the generic one.
Mathias Kresin [Mon, 23 Oct 2017 06:17:44 +0000 (08:17 +0200)]
ramips: don't enable usb for the WT3020-4M
That device does not have a USB port. It as the same board as the
WT3020-8M, but without soldered USB port port. Also the case lacks the
opening for the port.
Reported-by: Alberto Bursi <alberto.bursi@outlook.it> Signed-off-by: Mathias Kresin <dev@kresin.me>
Mathias Kresin [Mon, 16 Oct 2017 19:08:26 +0000 (21:08 +0200)]
ltq-adsl-app: add more script notifications
Backport HANDSHAKE and TRAINING notification from ltq-vdsl-app. It
unifies the dsl led blinking pattern accross all subtargets and allows
to get the current line status from the dsl led.
Mathias Kresin [Sat, 14 Oct 2017 18:52:22 +0000 (20:52 +0200)]
lantiq: xway: rename nas0/ptm0 to dsl0
This change makes it possible to configure the wan/dsl ppp interface
settings independantly from the used TC-Layer (ATM/PTM).
By using dsl0 as interface name as for the xrx200 we can get rid of a
few conditionals which were introduced because of the different default
TC-Layer in xway and xrx200.
Patch 610-netfilter_match_bypass_default_check added an extra flag IPT_F_NO_DEF_MATCH
which is copied to user space in function copy_entries_to_user. The 32bit compat
layer function was missing the same logic to copy the flag IPT_F_NO_DEF_MATCH to
user space for a 64bit kernel and 32 bit user space.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> Signed-off-by: Thierry Dutre <thierry.dutre@dtsystems.be>
Patch 610-netfilter_match_bypass_default_check added an extra flag IPT_F_NO_DEF_MATCH
which is copied to user space in function copy_entries_to_user. The 32bit compat
layer function was missing the same logic to copy the flag IPT_F_NO_DEF_MATCH to
user space for a 64bit kernel and 32 bit user space.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> Signed-off-by: Thierry Dutre <thierry.dutre@dtsystems.be>
Patch 610-netfilter_match_bypass_default_check added an extra flag IPT_F_NO_DEF_MATCH
which is copied to user space in function copy_entries_to_user. The 32bit compat
layer function was missing the same logic to copy the flag IPT_F_NO_DEF_MATCH to
user space for a 64bit kernel and 32 bit user space.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> Signed-off-by: Thierry Dutre <thierry.dutre@dtsystems.be>
Felix Fietkau [Tue, 24 Oct 2017 10:33:46 +0000 (12:33 +0200)]
ar71xx: re-enable 4k sectors for the mikrotik subtargets
On RB91x (and possibly others), there is a small SPI flash to store boot
loader and configuration. It needs 4K sectors to be able to write the
configuration using rbcfg
Some bootloaders set a cache cohenrency to a very slow mode. Use code from
Linux kernel to set it to "Cacheable, noncoherent, write-back, write
allocate".
Perfomance impact is significant on TP-Link EAP245 board, kernel
decompression time fall from 33 seconds to less than 1.
Stefan Oberhumer [Wed, 31 May 2017 05:37:03 +0000 (07:37 +0200)]
libs/lzo: Reenable unaligned access on ARM, PPC, ...
Due a compiler bug on ARM targets
( https://gcc.gnu.org/bugzilla/show_bug.cgi?id=64516 )
unaligned access was disabled on all targets other than i386 and
x86_64 with commit 061319ec3dfe9b6d14af1286a1d9979db56048d7 .
A fix has been added to lzo-2.09 so it is not necessary to disable
unaligned access within the Makefile anymore.
Signed-off-by: Stefan Oberhumer <stefan@obssys.com>
Florian Larysch [Thu, 3 Nov 2016 13:30:53 +0000 (14:30 +0100)]
toolchain: remove powerpc64 feature
The powerpc64 feature flag was introduced with the PS3 support, which
has been removed for quite a while and is now unused. Remove it and the
special biarch handling it triggered during the toolchain build.
Florian Fainelli [Sat, 14 Oct 2017 20:24:07 +0000 (13:24 -0700)]
uboot-sunxi: Backport fix for stale CONFIG_SUNXIG_GMAC references
This backports the upstream commit fixing stale references to
CONFIG_SUNXI_GMAC which have been later replaced by CONFIG_SUN7I_GMAC.
This fixes the designware MAC pinmuxing on e.g: Lamobo R1.
Florian Fainelli [Tue, 10 Oct 2017 03:33:34 +0000 (20:33 -0700)]
include: Include new location for DT bindings
Starting with commit d5d332d3f7e8 ("devicetree: Move include prefixes
from arch to separate directory") included in 4.12 and newer relocated
the dt-bindings directory, so account for that while passing CPPFLAGS
before DTC runs.
Stijn Tintel [Wed, 18 Oct 2017 17:17:56 +0000 (20:17 +0300)]
kernel: add kmod-iio-bmp280
This driver supports the Bosch Sensortec BMP180/BMP280 pressure and
temperature sensors. It also supports the BME280 sensors with an
additional humidity channel.
Tested I2C and SPI modes with a BME280 sensor on a Raspberry Pi Zero W.
Stijn Tintel [Sat, 21 Oct 2017 11:51:14 +0000 (14:51 +0300)]
brcm2708: restore /boot/config.txt before reboot
The Raspberry Pi bootloader reads configuration values from config.txt
in the boot partition. This file allows to specify the amount of memory
to assign to the GPU, the license keys for hardware MPEG-2 and VC-1
decoding, Device Tree parameters and overlays, and lots of other things.
Since sysupgrade only restores the configuration after booting the newly
flashed image, these values will not be active, even if sysupgrade would
save /boot/config.txt. To solve this, add the file to the files to be
backed up, and restore it in platform_copy_config, before reboot.
Hauke Mehrtens [Sun, 22 Oct 2017 13:20:39 +0000 (15:20 +0200)]
ar71xx: use kernel 4.9 by default
Kernel 4.9 support was added about 2 weeks ago and we haven't seen any
major regression so far. This patch was not ported to kernel 4.9, this
needs some additional work:
821-serial-core-add-support-for-boot-console-with-arbitr.patch
Hauke Mehrtens [Sun, 15 Oct 2017 17:21:38 +0000 (19:21 +0200)]
kernel: add config option
When the kmod-at91-adc package is activated for the at91 target the new
option CONFIG_AT91_SAMA5D2_ADC is selectable and not handled. Add this
option to the kernel 4.9 configuration.
Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Hauke Mehrtens [Wed, 18 Oct 2017 19:53:31 +0000 (21:53 +0200)]
brcm47xx: use kernel 4.9 by default
Kernel 4.9 is now working on the brcm47xx boards, we just recently fixed
the problem that some boards did not boot at all, by changing the memory
regions used to relocate the kernel to in the loader.
Felix Fietkau [Wed, 18 Oct 2017 20:46:29 +0000 (22:46 +0200)]
kernel: fix ftrace support on 4.9
When porting the kernel patches from 4.4 to 4.9, they were missing a
small chunk that ensures that ftrace sections are kept in the vmlinux
image, even when linked with --gc-sections
Hauke Mehrtens [Sun, 15 Oct 2017 19:43:59 +0000 (21:43 +0200)]
omap: Add support for kernel 4.9
This adds support for kernel 4.9 and replaces the kernel 4.4 support.
These are lynxis test results:
panda-board a3 - works, but no network, but master/4.4 doesn't have network either.
panda-board-a4 - u-boot SPL refuse to boot.
beaglebone-black - works
beagle-board - usb attached network doesn't come up and I doesn't have a serial around.
beagle-board-xm - ToDo: image code is missing.
Kernel 4.4 does not look better, so we merge this anyway.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Alexander Couzens <lynxis@fe80.eu>
Stijn Tintel [Wed, 18 Oct 2017 10:01:23 +0000 (13:01 +0300)]
hostapd: bump PKG_RELEASE
The previous commit did not adjust PKG_RELEASE, therefore the
hostapd/wpad/wpa_supplicant packages containing the AP-side workaround
for KRACK do not appear as opkg update.
Bump the PKG_RELEASE to signify upgrades to downstream users.
* noise: handshake constants can be read-only after init
* noise: no need to take the RCU lock if we're not dereferencing
* send: improve dead packet control flow
* receive: improve control flow
* socket: eliminate dead code
* device: our use of queues means this check is worthless
* device: no need to take lock for integer comparison
* blake2s: modernize API and have faster _final
* compat: support READ_ONCE
* compat: just make ro_after_init read_mostly
Assorted cleanups to the module, including nice things like marking our
precomputations as const.
* Makefile: even prettier output
* Makefile: do not clean before cloc
* selftest: better test index for rate limiter
* netns: disable accept_dad for all interfaces
Fixes in our testing and build infrastructure. Now works on the 4.14 rc
series.
* qemu: add build-only target
* qemu: work on ubuntu toolchain
* qemu: add more debugging options to main makefile
* qemu: simplify shutdown
* qemu: open /dev/console if we're started early
* qemu: phase out bitbanging
* qemu: always create directory before untarring
* qemu: newer packages
* qemu: put hvc directive into configuration
This is the beginning of working out a cross building test suite, so we do
several tricks to be less platform independent.
* tools: encoding: be more paranoid
* tools: retry resolution except when fatal
* tools: don't insist on having a private key
* tools: add pass example to wg-quick man page
* tools: style
* tools: newline after warning
* tools: account for padding being in zero attribute
Several important tools fixes, one of which suppresses a needless warning.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Stijn Tintel [Tue, 17 Oct 2017 13:35:03 +0000 (16:35 +0300)]
hostapd: add wpa_disable_eapol_key_retries option
Commit 2127425434046ae2b9f02fdbbdd37cac447af19c introduced an AP-side
workaround for key reinstallation attacks. This option can be used to
mitigate KRACK on the station side, in case those stations cannot be
updated. Since many devices are out there will not receive an update
anytime soon (if at all), it makes sense to include this workaround.
Unfortunately this can cause interoperability issues and reduced
robustness of key negotiation, so disable the workaround by default, and
add an option to allow the user to enable it if he deems necessary.
Stijn Tintel [Tue, 17 Oct 2017 13:24:14 +0000 (16:24 +0300)]
hostapd: backport extra changes related to KRACK
While these changes are not included in the advisory, upstream
encourages users to merge them.
See http://lists.infradead.org/pipermail/hostap/2017-October/037989.html
Felix Fietkau [Tue, 17 Oct 2017 13:52:08 +0000 (15:52 +0200)]
Revert "ar71xx: Add GRO support to ag71xx"
This reverts commit 13e5e473699b92f171205e0f5c57c9ebe7922492.
This commit causes a severe regression in LAN->WAN routing performance
for several devices. This appears to be caused by the extra requirement
to validate the SKB checksum early in the rx path, which the ethernet
hardware does not do
Hauke Mehrtens [Mon, 16 Oct 2017 19:36:17 +0000 (21:36 +0200)]
at91: fix legacy build
The build system took the DTB_SIZE definition from Default and not from
production-dtb under some conditions. Move the size definitions to
Default now as it is only used in production-dtb anyway.
Move wireguard from openwrt/packages to base a package.
This follows the pattern of kmod-cake and openvpn. Cake is a fast-moving
experimental kernel module that many find essential and useful. The
other is a VPN client. Both are inside of core. When you combine the two
characteristics, you get WireGuard. Generally speaking, because of the
extremely lightweight nature and "stateless" configuration of WireGuard,
many view it as a core and essential utility, initiated at boot time
and immediately configured by netifd, much like the use of things like
GRE tunnels.
WireGuard has a backwards and forwards compatible Netlink API, which
means the userspace tools should work with both newer and older kernels
as things change. There should be no versioning requirements, therefore,
between kernel bumps and userspace package bumps.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Acked-by: Jo-Philipp Wich <jo@mein.io> Acked-by: Felix Fietkau <nbd@nbd.name>
Hauke Mehrtens [Sun, 15 Oct 2017 12:33:56 +0000 (14:33 +0200)]
malta: activate some more standard kernel features
These options where deactivated in the malta kernel, take the default
options form the generic kernel configuration now to better match the
other targets.
projects / thirdparty / openwrt.git / log
