Arnd Bergmann [Fri, 21 Nov 2025 15:39:35 +0000 (16:39 +0100)]
Merge tag 'mtk-dts64-for-v6.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux into soc/dt
MediaTek ARM64 Device Tree updates
This adds support for new boards and variants based on different
already supported MediaTek SoCs, and improves support for current
boards.
In particular:
- New machines:
- MT7988 BananaPi R4 Pro eMMC and SD router board with support
for both Key-M and Key-E M.2 slots through DTB Overlays
- MT8370 Grinn GenioSBC-510 (GenioSOM-510 + GenioBoard Edge AI)
- MT8390 Grinn GenioSBC-700 (GenioSOM-700 + GenioBoard Edge AI)
- New variant: MT8395 MediaTek Genio 1200 EVK with UFS
...preparation for new SoCs (MT8196 Kompanio Ultra, a clone of the
MT6991 Dimensity 9400, and MT6878 Dimensity 7300) with the
addition of GCE/PIO definitions
...improvements for already supported SoCs and machines:
- MT7622/7981b/7986a/7988a gain support for reading SoC UUID from
eFuse, used to generate a persistent MAC address on boards that
don't have any factory-assigned addresses.
- MT7986 BananaPi R3 gets changes to its default fan PWM speed to
improve compatibility with cheaper fans (usually coming with the
heatsink+fan combos)
- The MT7981b OpenWRT One router sees general support improvements
with the enablement of its UART-0 console and correct pinmuxing
for the same, addition of reserved memory for Trusted Firmware A,
its SPI NOR Flash (for recovery system, WiFi eeprom data and ETH
MAC address from factory), and board LEDs.
- MT8365 gets support for its Mali G52 MC1 GPU, which gets enabled
in the MediaTek Genio 350 EVK board
...and a dt-bindings warning fix for MT8183 machines through trivial
changes to rename the audiosys and afe nodes to reflect bindings.
* tag 'mtk-dts64-for-v6.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux: (27 commits)
arm64: dts: mediatek: mt7981b-openwrt-one: Enable software leds
arm64: dts: mediatek: mt7981b-openwrt-one: Enable SPI NOR
arm64: dts: mediatek: mt7988a-bpi-r4pro: Add mmc overlays
arm64: dts: mediatek: mt7988a-bpi-r4-pro: Add PCIe overlays
arm64: dts: mediatek: mt7988: Add devicetree for BananaPi R4 Pro
arm64: dts: mediatek: mt7988: Disable 2.5G phy and enable at board layer
dt-bindings: arm: mediatek: add BPI-R4 Pro board
arm64: dts: mediatek: Add GCE header for MT8196
arm64: dts: mediatek: mt7981b: Add reserved memory for TF-A
arm64: dts: mediatek: mt7981b: Configure UART0 pinmux
arm64: dts: mediatek: mt8365-evk: Enable GPU support
arm64: dts: mediatek: mt8365: Add GPU support
arm64: dts: mediatek: mt8395-genio-1200-evk: Describe CPU supplies
arm64: dts: mediatek: Add MT6878 pinmux macro header file
arm64: dts: mediatek: mt7986-bpi-r3: Change fan PWM value for mid speed
arm64: dts: mediatek: mt8370-grinn-genio-510-sbc: Add Grinn GenioSBC-510
arm64: dts: mediatek: mt8390-genio-700-evk: Add Grinn GenioSBC-700
arm64: dts: mediatek: mt7988a: add 'soc-uuid' cell to efuse
arm64: dts: mediatek: mt7981b: add 'soc-uuid' cell to efuse
arm64: dts: mediatek: mt7986a: add 'soc-uuid' cell to efuse
...
Arnd Bergmann [Fri, 21 Nov 2025 15:38:23 +0000 (16:38 +0100)]
Merge tag 'mtk-dts32-for-v6.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux into soc/dt
MediaTek ARM32 Device Tree updates
This performs a cleanup of the MT6582 devicetrees and adds support
for secondary cores bringup on this SoC.
This also introduces basic support for a new machine, the MT6582
Alcatel "yarisxl" Pop C7 (OT-7041D) smartphone, with support for
booting into a initramfs with UART console output.
* tag 'mtk-dts32-for-v6.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux:
ARM: dts: mediatek: drop wrong syscon hifsys compatible for MT2701/7623
ARM: dts: mediatek: add basic support for Alcatel yarisxl board
dt-bindings: arm: mediatek: Add MT6582 yarisxl
ARM: dts: mediatek: mt6582: add enable-method property to cpus
ARM: dts: mediatek: mt6582: add clock-names property to uart nodes
ARM: dts: mediatek: mt6582: add mt6582 compatible to timer
ARM: dts: mediatek: mt6582: remove compatible property from root node
ARM: dts: mediatek: mt6582: sort nodes and properties
ARM: dts: mediatek: mt6582: move MMIO devices under soc node
Arnd Bergmann [Fri, 21 Nov 2025 15:36:49 +0000 (16:36 +0100)]
Merge tag 'samsung-dt64-6.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/dt
Samsung DTS ARM64 changes for v6.19
1. ExynosAutov920:
- Add more clock controller nodes.
2. Google GS101:
- PMIC clock
- Mark ACPM (Alive Clock and Power Manager) firmware node as clock
provider and use its clocks. Add also Devicetree binding headers
with clock its clock indices used in DTS (kept as separate branch).
- Add more SYSREG (syscon) regions.
- Correct several blocks address space sizes and APM SYSREG's starting
address.
3. Exynos7870:
- Enable display over DSI and several display planels.
- Few cleanups.
* tag 'samsung-dt64-6.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos7870-j6lte: enable display panel support
arm64: dts: exynos7870-a2corelte: enable display panel support
arm64: dts: exynos7870-on7xelte: enable display panel support
arm64: dts: exynos7870: add DSI support
arm64: dts: exynos: gs101: fix sysreg_apm reg property
arm64: dts: exynos: gs101: fix clock module unit reg sizes
arm64: dts: exynos: gs101: add sysreg_misc and sysreg_hsi0 nodes
arm64: dts: exynos: gs101: add OPPs
arm64: dts: exynos: gs101: add CPU clocks
arm64: dts: exynos: gs101: add #clock-cells to the ACPM protocol node
dt-bindings: firmware: google,gs101-acpm-ipc: add ACPM clocks
arm64: dts: exynos: gs101-pixel-common: add node for s2mpg10 / clock
arm64: dts: exynos990: Add sysreg nodes for PERIC0 and PERIC1
arm64: dts: exynosautov920: add CMU_MFC clock DT nodes
arm64: dts: exynosautov920: add CMU_M2M clock DT nodes
arm64: dts: exynos7870-on7xelte: add bus-width to mmc0 node
arm64: dts: exynos7870-j6lte: add bus-width to mmc0 node
arm64: dts: exynos7870-a2corelte: add bus-width to mmc0 node
Arnd Bergmann [Fri, 21 Nov 2025 15:35:57 +0000 (16:35 +0100)]
Merge tag 'thead-dt-for-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/fustini/linux into soc/dt
T-HEAD Devicetrees for v6.19
Add PWM controlled fan and it's associated thermal management for the
Lichee Pi 4A board.
Enable additional ISA extenstions supported by the T-Head C910 cores:
Zfh, Ziccrse, XTheadvector.
Add reset controllers of more TH1520 subsystems: AP, AO, DSP, MISC, VI.
Signed-off-by: Drew Fustini <fustini@kernel.org>
* tag 'thead-dt-for-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/fustini/linux:
riscv: dts: thead: Add reset controllers of more subsystems for TH1520
riscv: dts: thead: Add PWM fan and thermal control
riscv: dts: thead: Add PWM controller node
riscv: dts: thead: add zfh for th1520
riscv: dts: thead: add ziccrse for th1520
riscv: dts: thead: add xtheadvector to the th1520 devicetree
Arnd Bergmann [Fri, 21 Nov 2025 15:30:47 +0000 (16:30 +0100)]
Merge tag 'renesas-dts-for-v6.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
Renesas DTS updates for v6.19
- Add thermal support for the RZ/G3S and RZ/G3E SoCs,
- Add DT overlay support for the Raspberry Pi Display 2 and Argon40
fan hats on the Retronix Sparrow Hawk board,
- Add eMMC support for the Eagle Function expansion board,
- Add initial support for the R-Car X5H (R8A78000) SoC and the
Ironhide development board,
- Move interrupt-parent properties to root nodes,
- Add system watchdog timer support for R-Car Gen3 and Gen4 SoCs,
which is reserved for secure firmware on R-Car Gen3 boards,
- Add ADC support for the RZ/T2H and RZ/N2H SoCs and their evaluation
boards,
- Add watchdog timer support on the R-Car V3M Starter Kit board,
- Add Cortex-A55 PMU support on the RZ/V2H, RZ/V2N, RZ/T2H, and RZ/N2H
SoCs,
- Add Imagination Technologies PowerVR Series 6XT GX6250 GPU support
on the R-Car M3-W and M3-W+ SoCs,
- Miscellaneous fixes and improvements.
Arnd Bergmann [Fri, 21 Nov 2025 15:28:42 +0000 (16:28 +0100)]
Merge tag 'aspeed-6.19-devicetree-0' of https://git.kernel.org/pub/scm/linux/kernel/git/bmc/linux into soc/dt
First batch of ASPEED Arm devicetree changes for 6.19
Significant changes:
- The IBM Power11 FSI DTSIs have been rearranged to accommodate new systems
New platforms:
- IBM Balcones
The Balcones system is similar to Bonnell but with a POWER11 processor.
Like POWER10, the POWER11 is a dual-chip module, so a dual chip FSI
tree is needed.
- Meta Yosemite5
The Yosemite5 platform provides monitoring of voltages, power,
temperatures, and other critical parameters across the motherboard,
CXL board, E1.S expansion board, and NIC components.
Updated platforms:
- clemente (Meta): LEDs, shunt resistor configuration
- santabarbara (Meta): AMD APML, EEPROMs, LEDs, GPIO line names, MCTP for NICs
There are a scattering of one-off changes and devicetree cleanups for other
platforms as well.
* tag 'aspeed-6.19-devicetree-0' of https://git.kernel.org/pub/scm/linux/kernel/git/bmc/linux:
ARM: dts: aspeed: santabarbara: Add eeprom device node for PRoT module
ARM: dts: aspeed: santabarbara: Add AMD APML interface support
ARM: dts: aspeed: santabarbara: Add gpio line name
ARM: dts: aspeed: santabarbara: Add bmc_ready_noled Led
ARM: dts: aspeed: santabarbara: Enable MCTP for frontend NIC
ARM: dts: aspeed: santabarbara: Add sensor support for extension boards
ARM: dts: aspeed: santabarbara: Add blank lines between nodes for readability
ARM: dts: aspeed: yosemite5: Add Meta Yosemite5 BMC
dt-bindings: arm: aspeed: add Meta Yosemite5 board
ARM: dts: aspeed: clemente: Add HDD LED GPIO
ARM: dts: aspeed: Fix max31785 fan properties
ARM: dts: aspeed: Add Balcones system
dt-bindings: arm: aspeed: add IBM Bonnell board
dt-bindings: arm: aspeed: add IBM Balcones board
ARM: dts: aspeed: harma: Add MCTP I2C controller node
ARM: dts: aspeed: yosemite4: allocate ramoops for kernel panic
ARM: dts: aspeed: clemente: add shunt-resistor-micro-ohms for LM5066i
Arnd Bergmann [Fri, 21 Nov 2025 15:26:17 +0000 (16:26 +0100)]
Merge tag 'pxa1908-dt-for-6.19' of https://gitlab.com/pxa1908-mainline/linux into soc/dt
PXA1908 DT changes for 6.19
Rollup of hardware support which has accumulated since support for the
SoC and coreprimevelte board was merged. This most notably includes
eMMC, PMIC, backlight and touchscreen. A few QoL fixes are also
included.
* tag 'pxa1908-dt-for-6.19' of https://gitlab.com/pxa1908-mainline/linux:
arm64: dts: marvell: pxa1908: Add power domains
arm64: dts: marvell: samsung,coreprimevelte: Add USB connector
arm64: dts: marvell: samsung,coreprimevelte: Fill in memory node
arm64: dts: marvell: samsung,coreprimevelte: Drop some reserved memory
arm64: dts: marvell: pxa1908: Move ramoops to SoC dtsi
arm64: dts: marvell: samsung,coreprimevelte: Add vibrator
arm64: dts: marvell: pxa1908: Add PWMs
arm64: dts: marvell: samsung,coreprimevelte: Enable eMMC
arm64: dts: marvell: samsung,coreprimevelte: Correct CD GPIO
arm64: dts: marvell: samsung,coreprimevelte: Add backlight
arm64: dts: samsung,coreprimevelte: add SDIO
arm64: dts: samsung,coreprimevelte: add touchscreen
arm64: dts: samsung,coreprimevelte: add PMIC
The openwrt has 3 status leds at the front:
* red: Used as failsafe led by openwrt
* white: Used as boot led by openwrt
* green: Used as running/upgrade led by openwrt
On the back each RJ45 jack has the typical amber/green leds. For the WAN
jack this is hardware controlled by the phy, for LAN these are under
software control and enabled by this patch.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Frank Wunderlich [Mon, 27 Oct 2025 13:28:12 +0000 (14:28 +0100)]
dt-bindings: arm: mediatek: add BPI-R4 Pro board
Add compatibles for Bananapi R4 Pro boards.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Jason-JH Lin [Fri, 31 Oct 2025 15:56:29 +0000 (23:56 +0800)]
arm64: dts: mediatek: Add GCE header for MT8196
Add GCE header define for GCE Thread Priority and GCE Event IDs
that used in the MT8196 dtsi.
Signed-off-by: Jason-JH Lin <jason-jh.lin@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Sjoerd Simons [Sat, 1 Nov 2025 13:32:47 +0000 (14:32 +0100)]
arm64: dts: mediatek: mt7981b: Add reserved memory for TF-A
Add memory range handled by ARM Trusted Firmware
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sjoerd Simons <sjoerd@collabora.com> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
arm64: dts: exynos7870-j6lte: enable display panel support
Enable DECON and DSI nodes, and add the compatible display panel and
appropriate panel timings for this device. Also, remove the
simple-framebuffer node in favor of the panel.
This device has a 720x1480 AMOLED Samsung AMS561RA01 panel with
S6E8AA5X01 controller.
arm64: dts: exynos7870-a2corelte: enable display panel support
Enable DECON and DSI nodes, and add the compatible display panel and
appropriate panel timings for this device. Also, remove the
simple-framebuffer node in favor of the panel.
This device has a 540x960 Synaptics TD4101 display panel.
arm64: dts: exynos7870-on7xelte: enable display panel support
Enable DECON and DSI nodes, and add the compatible display panel and
appropriate panel timings for this device. Also, remove the
simple-framebuffer node in favor of the panel.
This device has a 1080x1920 Synaptics TD4300 display panel.
Add devicetree nodes for MIPI PHYs, Samsung's DECON and DSIM blocks, and
DECON IOMMU devicetree nodes. Enables SoC support for hardware to be
able to drive a MIPI DSI display.
Yao Zi [Tue, 14 Oct 2025 13:10:32 +0000 (13:10 +0000)]
riscv: dts: thead: Add reset controllers of more subsystems for TH1520
Describe reset controllers for VI, MISC, AP, DSP and AO subsystems. The
one for AO subsystem is marked as reserved, since it may be used by AON
firmware.
Reviewed-by: Drew Fustini <fustini@kernel.org> Signed-off-by: Yao Zi <ziyao@disroot.org> Signed-off-by: Drew Fustini <fustini@kernel.org>
Marek Vasut [Mon, 27 Oct 2025 18:45:53 +0000 (19:45 +0100)]
arm64: dts: renesas: sparrow-hawk: Fix full-size DP connector node name and labels
The DisplayPort connector on Retronix R-Car V4H Sparrow Hawk board
is a full-size DisplayPort connector. Fix the copy-paste error and
update the DT node name and labels accordingly. No functional change.
Wolfram Sang [Tue, 7 Oct 2025 10:46:25 +0000 (12:46 +0200)]
ARM: dts: renesas: r9a06g032-rzn1d400-db: Drop invalid #cells properties
The 'ethernet-ports' node in the SoC DTSI handles them already. Fixes:
arch/arm/boot/dts/renesas/r9a06g032-rzn1d400-db.dtb: switch@44050000 (renesas,r9a06g032-a5psw): Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
from schema $id: http://devicetree.org/schemas/net/dsa/renesas,rzn1-a5psw.yaml#
Use the more modern adi,adv7180cp compatible for the CVBS input found on
R-Car Gen2 Koelsch boards. This aligns the bindings with the other Gen2
board with the same setup Gose.
ARM: dts: renesas: r8a7794: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
ARM: dts: renesas: r8a7793: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
ARM: dts: renesas: r8a7792: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
ARM: dts: renesas: r8a7791: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
ARM: dts: renesas: r8a7790: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
ARM: dts: renesas: r8a77470: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
ARM: dts: renesas: r8a7745: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
ARM: dts: renesas: r8a7744: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
ARM: dts: renesas: r8a7743: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
ARM: dts: renesas: r8a7742: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
ARM: dts: renesas: r7s72100: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
Wolfram Sang [Mon, 29 Sep 2025 09:36:02 +0000 (11:36 +0200)]
ARM: dts: renesas: gose: Remove superfluous port property
'bus-width' is defined for the corresponding vin input port already.
No need to declare it in the output port again. Fixes:
arch/arm/boot/dts/renesas/r8a7793-gose.dtb: composite-in@20 (adi,adv7180cp): ports:port@3:endpoint: Unevaluated properties are not allowed ('bus-width' was unexpected)
from schema $id: http://devicetree.org/schemas/media/i2c/adi,adv7180.yaml#
Wolfram Sang [Thu, 25 Sep 2025 09:39:51 +0000 (11:39 +0200)]
arm64: dts: renesas: eagle/v3msk: Mark SWDT as reserved
This watchdog can't be used with Linux because the firmware needs it on
V3M boards. Sadly, it doesn't mark the node as reserved, so this is
added manually here.
Wolfram Sang [Thu, 25 Sep 2025 09:39:50 +0000 (11:39 +0200)]
arm64: dts: renesas: ebisu: Mark SWDT as reserved
This watchdog can't be used with Linux because the firmware needs it on
Ebisu boards. Sadly, it doesn't mark the node as reserved, so this is
added manually here.
Wolfram Sang [Thu, 25 Sep 2025 09:39:49 +0000 (11:39 +0200)]
arm64: dts: renesas: draak: Mark SWDT as reserved
This watchdog can't be used with Linux because the firmware needs it on
Draak boards. Sadly, it doesn't mark the node as reserved, so this is
added manually here.
Wolfram Sang [Thu, 25 Sep 2025 09:39:48 +0000 (11:39 +0200)]
arm64: dts: renesas: ulcb: Mark SWDT as reserved
This watchdog can't be used with Linux because the firmware needs it on
ULCB boards. Sadly, it doesn't mark the node as reserved, so this is
added manually here.
Wolfram Sang [Thu, 25 Sep 2025 09:39:47 +0000 (11:39 +0200)]
arm64: dts: renesas: salvator-common: Mark SWDT as reserved
This watchdog can't be used with Linux because the firmware needs it on
Salvator boards. Sadly, it doesn't mark the node as reserved, so this is
added manually here.
arm64: dts: renesas: r9a09g087: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r9a09g077: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r9a09g057: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r9a09g056: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r9a09g047: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r9a09g011: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r9a08g045: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r9a07g054: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r9a07g044: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r9a07g043u: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r8a779h0: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r8a779g0: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r8a779f0: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r8a779a0: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r8a77995: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r8a77990: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r8a77980: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r8a77970: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r8a77965: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r8a77961: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r8a77960: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r8a77951: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r8a774e1: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r8a774c0: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r8a774b1: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: renesas: r8a774a1: Move interrupt-parent to root node
Move the "interrupt-parent = <&gic>" property from the soc node to the
root node, and simplify "interrupts-extended = <&gic ...>" to
"interrupts = <...>".
arm64: dts: mediatek: mt8365-evk: Enable GPU support
Enable for the Mediatek Genio 350-EVK board the support of the
Arm Mali G52 MC1 GPU integrated in the MT8365 SoC.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The Mediatek MT8365 SoC has an integrated Arm Mali G52 MC1 GPU
(Bifrost).
Add gpu, OPP table, and MFG clock driver nodes in mt8365.dtsi to support
it using the Panfrost driver.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
arm64: dts: mediatek: mt8395-genio-1200-evk: Describe CPU supplies
The Genio 1200 EVK board has the big and little CPU clusters fed by the
same regulators as MT8195-Cherry boards, so describe them in the same
way as commit 17b33dd9e4a3 ("arm64: dts: mediatek: cherry: Describe CPU
supplies").
This prevents the system from hanging during boot in the case that the
cpufreq-mediatek-hw driver tries to probe before the drivers for the
regulators have probed (which happens when using the current defconfig).
Fixes: f2b543a191b6 ("arm64: dts: mediatek: add device-tree for Genio 1200 EVK board") Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
projects / thirdparty / kernel / linux.git / log
