Sean Bright [Mon, 20 Feb 2012 18:39:22 +0000 (18:39 +0000)]
Remove spurious warning when 'qualifyfreqnotok' is set successfully.
(closes issue ASTERISK-17176)
Reported by: John Covert
Tested by: Sean Bright
Patches:
chan_iax2.c.qualifyfreqnotok.patch uploaded by John Covert (license 5512)
........
Merged revisions 355997 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Alec L Davis [Sat, 18 Feb 2012 07:58:43 +0000 (07:58 +0000)]
push 'outgoing' flag from sig_XXX up to chan_dahdi
'p->outgoing' in chan_dahdi and sig_analog wern't kept in sync, particulary FXS ast_hangup didn't clear the 'outgoing' flag.
sig_pri and sig_ss7 were keeping 'outgoing' flag insync.
Now provides a callback for all the low level sig_XXX modules.
(issue ASTERISK-19316)
alecdavis (license 585)
Reported by: Jeremy Pepper
Tested by: alecdavis
Sean Bright [Fri, 17 Feb 2012 19:34:17 +0000 (19:34 +0000)]
Pass the correct value to ast_timer_set_rate() for IAX2 trunking.
IAX2 uses the trunkfreq variable to determine how often to send trunk packets, but
this value is in milliseconds while ast_timer_set_rate() expects the rate argument
to be ticks per second. So we divide 1000 by trunkfreq and pass that in instead.
With a default of 20ms, this change makes IAX2 send trunk packets every 20ms
instead of every 50ms.
Tracked down by myself and Bob Wienholt.
........
Merged revisions 355746 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Mark Michelson [Fri, 17 Feb 2012 19:06:57 +0000 (19:06 +0000)]
Fix regressions with regards to route-set creation on early dialogs.
This fixes two main issues:
1. Asterisk would send a CANCEL to the route created by the provisional response
instead of using the same destination it did in the initial INVITE.
2. If a new route set arrives in a 200 OK than was in the 1XX response (perfectly
possible if our outbound INVITE gets forked), then the route set in the 200 OK
needs to overwrite the route set in the 1XX response.
(closes issue ASTERISK-19358)
Reported by: Karsten Wemheuer
Tested by: Karsten Wemheuer
patches:
ASTERISK-19358.patch uploaded by Mark Michelson (license 5049)
ASTERISK-19358.patch uploaded by Stefan Schmidt (license 6034)
Sean Bright [Thu, 16 Feb 2012 20:01:59 +0000 (20:01 +0000)]
Revert a change to audio_audiohook_write_list that had no affect.
When I made this change initially, I was under the false impression that the
audiohooks structure remained on the channel after all of the hooks had been
detached. This is not the case, ast ast_read takes care of removing the
audiohooks structure if the lists are empty.
........
Merged revisions 355622 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Richard Mudgett [Thu, 16 Feb 2012 19:44:44 +0000 (19:44 +0000)]
Fix compile problem when old version of libvorbisfile v1.1.2 is used.
The principle difference between libvorbisfile v1.1.2 and newer (at least
v1.2.0) is the addition of the predefined callbacks OV_CALLBACKS_xxx in
vorbis/vorbisfile.h used for ov_open_callbacks().
* Updated the configure script to detect if libvorbisfile.h declares
OV_CALLBACKS_NOCLOSE.
* Copied the declaration of OV_CALLBACKS_NOCLOSE from v1.2.0 to allow
v1.1.2 to compile.
(closes issue ASTERISK-19370)
Reported by: Jonn Taylor
........
Merged revisions 355608 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Sean Bright [Wed, 15 Feb 2012 17:25:40 +0000 (17:25 +0000)]
Use TRUNK_CALL_START as originally intended.
Back in r646, TRUNK_CALL_START was added and defined as 0x4000. That same value
was also hard-coded in one part of the IAX2 code instead of using the #define.
TRUNK_CALL_START has changed over the years (for dealing with LOW_MEMORY), but
the hard-coded usage was never updated to match. This patch fixes that.
........
Merged revisions 355448 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Sean Bright [Tue, 14 Feb 2012 13:33:51 +0000 (13:33 +0000)]
Clear the high order bit from the destination call number before sending.
send_apathetic_reply takes the incoming frame's source call number as the
destination call number for the outgoing frame. If the incoming frame was a
full frame, then the high order bit of the source call number is set and will be
interpreted as a retransmit when sent back out as the destination call number.
........
Merged revisions 355182 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Since the dir timestamp is available at one second resolution, we cannot
know if it was updated within the same second after we scanned it.
Therefore, we will force another scan if the dir was just modified.
* Changed to force another scan if the directory was just modified.
Richard Mudgett [Mon, 13 Feb 2012 17:24:01 +0000 (17:24 +0000)]
Fix reconnecting to pgsql database after connection loss.
There can only be one database connection in res_config_pgsql just like
res_config_sqlite. If the connection is lost, the connection may not get
reestablished to the same database if the res_pgsql.conf and
extconfig.conf files are inconsistent.
* Made only use the configured database from res_pgsql.conf.
* Fixed potential buffer overwrite of last[] in config_pgsql().
(closes issue ASTERISK-16982)
Reported by: german aracil boned
Jason Parker [Fri, 10 Feb 2012 22:00:10 +0000 (22:00 +0000)]
Fix a voicemail memory leak with heard/deleted messages.
open_mailbox() was changed quite a long time ago to allocate this memory.
close_mailbox() should have been changed to be responsible for freeing it.
........
Merged revisions 354889 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Terry Wilson [Thu, 9 Feb 2012 22:03:51 +0000 (22:03 +0000)]
Note that CDRs are immutable once a bridge is torn down
CDRs cannot be modified after a bridge is torn down, (e.g. after
Dial() returns) even though the CDR() function may be called. Since
modifying the CDR code to change this behavior could very easily
break all kinds of things, this patch just documents this limitation.
Kinsey Moore [Thu, 9 Feb 2012 20:51:34 +0000 (20:51 +0000)]
Fix parsing of SIP headers where compact and non-compact headers are mixed
Change parsing of SIP headers so that compactness of the header no longer
influences which header will be chosen. Previously, a non-compact header
would be chosen instead of a preceeding compact-form header.
Kinsey Moore [Thu, 9 Feb 2012 19:54:04 +0000 (19:54 +0000)]
Make the config parser remove escaping backslashes
The config parser in Asterisk does not currently remove a backslash that is
used to escape a semicolon which would otherwise be interpreted as the start
of a comment.
The change here causes that backslash to be removed, but does not create a
real escape system in the config parser. The biggest complication with a real
escape system would be breaking existing configs everywhere (parsing \\ as \
and breaking on escaped non-semicolon characters) even though it would be the
"right" way to do things.
Matthew Jordan [Thu, 9 Feb 2012 16:35:43 +0000 (16:35 +0000)]
Fix SIP INFO DTMF handling for non-numeric codes
In ASTERISK-18924, SIP INFO DTMF handlingw as changed to account for both
lowercase alphatbetic DTMF events, as well as uppercase alphabetic DTMF
events. When this occurred, the comparison of the character buffer containing
the event code was changed such that the buffer was first compared again '0'
and '9' to determine if it was numeric. Unfortunately, since the first
character in the buffer will typically be '1' in the case of non-numeric
event codes (10-16), this caused those codes to be converted to a DTMF event
of '1'. This patch fixes that, and cleans up handling of both
application/dtmf-relay and application/dtmf content types.
Russell Bryant [Thu, 9 Feb 2012 02:25:28 +0000 (02:25 +0000)]
Remove some unnecessary locking from ast_hangup().
This patch removes some unnecessary locking of the channels container in
ast_hangup(). The reason this came up is that this lock can very quickly block
the entire system. If any of the channel cleanup code decides to block, it
causes a problem for the whole system. For example, when audiohooks get
destroyed, if that blocks for a while waiting on the mixmonitor thread to exit
because it's busy blocking on some I/O, it causes a problem for many other
threads in the meantime.
Terry Wilson [Tue, 7 Feb 2012 21:17:10 +0000 (21:17 +0000)]
Fix multiple SIP realtime issues
1. Set lastms to 0 when clearing instead of ""
2. Don't set ipaddr or port to the string "(null)" when they are empty
3. Add missing required fields, set default for lastms to 0, and modify
the length of the ipaddr field to 45 in the Postgresql realtime.sql
file.
Jonathan Rose [Tue, 7 Feb 2012 15:19:51 +0000 (15:19 +0000)]
Fix column duplication bug in module reload for cdr_pgsql.
Prior to this patch, attempts to reload cdr_pgsql.so would cause the column list to keep
its current data and then add a second copy during the reload. This would cause attempts
to log the CDR to the database to fail. This patch also cleans up some unnecessary null
checks for ast_free and deals with a few potential locking problems.
(closes issue ASTERISK-19216)
Reported by: Jacek Konieczny
Review: https://reviewboard.asterisk.org/r/1711/
........
Merged revisions 354263 from http://svn.asterisk.org/svn/asterisk/branches/1.8
* Allow acceptance of command without the app-data value. There are many
applications that do no need any parameters so it is silly to require that
field for all commands.
* Fixed a couple ast_malloc/ast_free mismatches with ast_add_extension2()
calls.
Jonathan Rose [Fri, 3 Feb 2012 21:25:27 +0000 (21:25 +0000)]
Fixes deadlocks occuring in chan_agent due to r335976
Bad locking order was added to chan_agent to prevent segfaults from having no locking
in a patch by irroot. This patch addresses the bad locking order by releasing locks before
getting the right locking order to stop deadlocks from occuring when doing multiple
interactions with agents.
Kinsey Moore [Thu, 2 Feb 2012 22:27:42 +0000 (22:27 +0000)]
Ensure entering T.38 passthrough does not cause an infinite loop
After R340970 Asterisk was still polling the RTCP file descriptor after RTCP is
shut down and removed. If the descriptor happened to have data ready when the
removal occured then Asterisk would go into an infinite loop trying to read
data that it can never actually access. This change disables the audio RTCP
file descriptor for the duration of the T.38 transaction.
Mark Michelson [Thu, 2 Feb 2012 18:48:05 +0000 (18:48 +0000)]
Fix TLS port binding behavior as well as reload behavior:
* Removes references to tlsbindport from http.conf.sample and manager.conf.sample
* Properly bind to port specified in tlsbindaddr, using the default port if specified.
* On a reload, properly close socket if the service has been disabled.
A note has been added to UPGRADE.txt to indicate how ports must be set for TLS.
(closes issue ASTERISK-16959)
reported by Olaf Holthausen
(closes issue ASTERISK-19201)
reported by Chris Mylonas
(closes issue ASTERISK-19204)
reported by Chris Mylonas
Jonathan Rose [Thu, 2 Feb 2012 18:32:07 +0000 (18:32 +0000)]
Blocked revisions 353818
........
Backports some documentation for func_curl from 10 to 1.8
For some reason this function was completely undocumented in 1.8. I copied the
10 docs over to 1.8 and removed references to an enumerator that was added in
the Asterisk 10 version of func_curl. That was the only change I noted.
Jonathan Rose [Thu, 2 Feb 2012 17:06:41 +0000 (17:06 +0000)]
Fix sip show peers port output, align columns, and fix ami port output.
A previous patch I committed from ASTERISK-16930 unexpectedly changed some output for
the AMI action "sippeers" which this patch changes back. Also, this aligns the output
for the cli command "sip show peers" and fixes another issue that patch introduced by
using ast_sockaddr_stringify calls multiple times without immediately using the pointer.
I also went ahead and did a little janitorial work to clean up whitespace in
_sip_show_peers.
(issue ASTERISK-16930)
(closes issue ASTERISK-19281)
Reported by: Patrick El Youssef
Patches:
ASTERISK-19281.diff uploaded by Walter Doekes (license 5674)
........
Merged revisions 353769 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Jonathan Rose [Wed, 1 Feb 2012 21:16:53 +0000 (21:16 +0000)]
Use ast_sockaddr_stringify_fmt wrappers for various functions in chan_sip
There are a number of cleaner looking wrappers for ast_sockaddr_stringify_fmt
available which are slightly more readable than using a direct call to
ast_sockaddr_stringify_fmt. This patch switches a number of those calls in
chan_sip to use those wrappers and is generally harmless.
(Closes issue ASTERISK-16930)
Reported by: Michael L. Young
Patches:
chan_sip-broken-registration-1.8.diff uploaded by Michael L. Young (license 5026)
........
Merged revisions 353720 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Sean Bright [Wed, 1 Feb 2012 15:51:29 +0000 (15:51 +0000)]
Resolve an overlap in the ast_audiohook_flags values.
AST_AUDIOHOOK_TRIGGER_WRITE and AST_AUDIOHOOK_WANTS_DTMF were overlapping which
may have caused unintended side effects. This patch moves
AST_AUDIOHOOK_TRIGGER_WRITE, and updates AST_AUDIOHOOK_TRIGGER_MODE to reflect
the original intention.
This will affect existing modules that use these flags, so be sure to recompile
as necessary.
Matthew Jordan [Wed, 1 Feb 2012 15:05:34 +0000 (15:05 +0000)]
Added clarification for the VERBOSITY setting to etc_default_asterisk
Clarified that using the VERBOSITY setting in etc_default_asterisk is the
same as using the -v command line switch, which causes Asterisk to launch
in console mode.
(closes issue ASTERISK-17030)
Reported by: Jonas
........
Merged revisions 353550 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Terry Wilson [Wed, 1 Feb 2012 00:00:02 +0000 (00:00 +0000)]
Allow res_calendar to be unloaded
The calendaring tech modules depend on res_calendar and initially
res_calendar just bumped the use count so that it couldn't be unloaded.
res_calendar can potentially create many threads and I've seen issues
where the Asterisk shutdown has failed where it looked like these
threads could be the culprit.
This patch adds unload support for res_calendar. Unloading res_calendar
will also unload the dependant tech modules as well.
Richard Mudgett [Tue, 31 Jan 2012 17:21:17 +0000 (17:21 +0000)]
Fix memory leak in error paths for action_originate().
* Fix memory leak of vars in error paths for action_originate().
* Moved struct fast_originate_helper tech and data members to stringfields.
* Simplified ActionID header handling for fast_originate().
* Added doxygen note to ast_request() and ast_call() and the associated
channel callbacks that the data/addr parameters should be treated as const
char *.
Terry Wilson [Mon, 30 Jan 2012 23:28:10 +0000 (23:28 +0000)]
Re-link peers by IP when dnsmgr changes the IP
Asterisk's dnsmgr currently takes a pointer to an ast_sockaddr and updates it
anytime an address resolves to something different. There are a couple of
issues with this. First, the ast_sockaddr is usually the address of an
ast_sockaddr inside a refcounted struct and we never bump the refcount of those
structs when using dnsmgr. This makes it possible that a refresh could happen
after the destructor for that object is called (despite ast_dnsmgr_release
being called in that destructor). Second, the module using dnsmgr cannot be
aware of an address changing without polling for it in the code. If an action
needs to be taken on address update (like re-linking a SIP peer in the
peers_by_ip table), then polling for this change negates many of the benefits
of having dnsmgr in the first place.
This patch adds a function to the dnsmgr API that calls an update callback
instead of blindly updating the address itself. It also moves calls to
ast_dnsmgr_release outside of the destructor functions and into cleanup
functions that are called when we no longer need the objects and increments the
refcount of the objects using dnsmgr since those objects are stored on the
ast_dnsmgr_entry struct. A helper function for returning the proper default SIP
port (non-tls vs tls) is also added and used.
This patch also incorporates changes from a patch posted by Timo Teräs to
ASTERISK-19106 for related dnsmgr issues.
RFC3261 Section 8.1.1.5. The sequence number value MUST be expressible as a 32-bit unsigned integer
* fix: use %u instead of %d when dealing with CSeq numbers - to remove possibility of -ve numbers.
* fix: change all uses of seqno and friends (ocseq icseq) from 'int' or 'unsigned int' to uint32_t.
Summary of CSeq numbers.
An initial CSeq number must be less than 2^31
A CSeq number can increase in value up to 2^32-1
An incrementing CSeq number must not wrap around to 0.
Tested with Asterisk 1.8.8.2 with Grandstream phones.
Kevin P. Fleming [Mon, 30 Jan 2012 12:48:31 +0000 (12:48 +0000)]
Clarify log WARNING message when port-zero SDP 'm' lines received.
Previously, if an m-line in an SDP offer or answer had a port number of zero,
that line was skipped, and resulted in an 'Unsupported SDP media type...'
warning message. This was misleading, as the media type was not unsupported,
but was ignored because the m-line indicated that the media stream had been
rejected (in an answer) or was not going to be used (in an offer).
........
Merged revisions 353260 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Russell Bryant [Sun, 29 Jan 2012 02:44:24 +0000 (02:44 +0000)]
Find even more network interfaces.
The previous change made the code look for emN and pciN in addition to what
it did originally, which was search for ethN. However, it needed to be looking
for pciN#N, so that's what it does now.
This also moves the memset() to be before every ioctl().
........
Merged revisions 353175 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Kevin P. Fleming [Sat, 28 Jan 2012 14:51:29 +0000 (14:51 +0000)]
Add 'L16-256' MIME subtype alias for slin16.
Asterisk has supported the 'L16' MIME subtype for 16kHz signed linear (PCM)
audio for quite some time, but some endpoints refer to it as 'L16-256'. This
commit adds this as an alias for the existing format.
........
Merged revisions 353126 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Russell Bryant [Sat, 28 Jan 2012 04:27:55 +0000 (04:27 +0000)]
Update ast_set_default_eid() to find more network interfaces.
As of Fedora 15, ethN is not the name of ethernet interfaces. The names
are emN or pciN. Update some code that searched for interfaces named
ethN to look for the new names, as well. For more information about why
this change was made, see this page:
http://domsch.com/blog/?p=455
........
Merged revisions 353077 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Jonathan Rose [Fri, 27 Jan 2012 19:19:46 +0000 (19:19 +0000)]
Make failed PauseMonitor and UnpauseMonitor with no valid channel not close AMI session.
I also went ahead and took a little time to make sure that the manager value
AMI_SUCCESS was used instead of just return 0 being thrown around everywhere since that's
how we handle this stuff these days.
rfc4235 - Section 4.1: Versions MUST be representable using a non-negative 32 bit integer.
If a BLF subscription exists for long enough, using %d may print negative version numbers.
Unlikely, as 2^32 at 1 update per second is ~137 years, or half that before the versions number started going negative.
Tested with Asterisk 1.8.8.2 with Grandstream phones.
Jonathan Rose [Thu, 26 Jan 2012 19:07:01 +0000 (19:07 +0000)]
Copy amaflags to sip_pvt from peer during create_addr_from_peer
For whatever reason, we don't have a single function for copying data like this
from SIP peers to the SIP pvt. This patch adds the copying of amaflags to the
sip_pvt, but it would probably be worth discussing this function along with
the others that essentially just copy some amount of data from a peer to a
private.
(Closes issue ASTERISK-19029)
Reported by: Matt Lehner
........
Merged revisions 352755 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Kevin P. Fleming [Wed, 25 Jan 2012 21:18:22 +0000 (21:18 +0000)]
Avoid unnecessary rebuilds of main/test.c.
main/test.c includes "asterisk/version.h", when it should include
"asterisk/ast_version.h" instead (and it should use the ast_get_version()
and ast_get_version_num() functions). This commit modifies it to extract
the Asterisk version information using the proper APIs, and as a result means
that main/test.c no longer needs to be rebuilt when a Subversion checkout
is updated or modified.
........
Merged revisions 352612 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Richard Mudgett [Wed, 25 Jan 2012 17:16:22 +0000 (17:16 +0000)]
Fixes for sending SIP MESSAGE outside of calls.
* Fix authenticate MESSAGE losing custom headers added by the MESSAGE_DATA
function in the authorization attempt.
* Pass up better From header contents for SIP to use. Now is in the
"display-name" <URI> format expected by MessageSend. (Note that this is a
behavior change that could concievably affect some people.)
* Block user from adding standard headers that are added automatically.
(To, From,...)
* Allow the user to override the Content-Type header contents sent by
MessageSend.
* Decrement Max-Forwards header if the user transferred it from an
incoming message.
* Expand SIP short header names so the dialplan and other code only has to
deal with the full names.
* Documents what SIP expects in the MessageSend(from) parameter.
(closes issue ASTERISK-18992)
Reported by: Yuri
(closes issue ASTERISK-18917)
Reported by: Shaun Clark
Kevin P. Fleming [Wed, 25 Jan 2012 16:54:21 +0000 (16:54 +0000)]
Eliminate unnecessary rebuilds of main/format*.c.
These files have no need to include "asterisk/version.h", and doing so forces
them to be rebuilt each time a Subversion checkout moves between 'modified'
and 'unmodified' states.
Jonathan Rose [Wed, 25 Jan 2012 16:41:29 +0000 (16:41 +0000)]
Redocuments sip types peer, user, friend in sip.conf.sample
There was faulty information in the sample config describing user as a synonym for friend
so it has been changed to better elaborate on the differences between the three entity
types.
Jonathan Rose [Tue, 24 Jan 2012 20:35:38 +0000 (20:35 +0000)]
Set core sounds version to 1.4.22.
Now that we have the right license for the Russian 1.4.22 sounds as well as the sounds
for the Australian English 1.4.22 sounds, we can finally set the sounds to use 1.4.22!
(closes issue ASTERISK-18978)
Reported by: Cameron Twomey
Patches:
confbridge.tar.001 uploaded by Cameron Twomey
confbridge.tar.002 uploaded by Cameron Twomey
........
Merged revisions 352367 from http://svn.asterisk.org/svn/asterisk/branches/1.8
While the FAXOPT function could be used to set the modem capabilities, the
input to that function was not being applied correctly to the spandsp layer.
This patch applies the current model capabilities before starting the spandsp
layer.
(closes issue: ASTERISK-16409)
Reported by: Kristijan Vrban
Tested by: Matt Jordan, Matthew Nicholson
Patches:
spandsp-modems-1.8.diff uploaded by mnicholson (license 5081)
spandsp-modems-10.diff uploaded by mnicholson (license 5081)
........
Merged revisions 352144 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Mark Michelson [Sat, 21 Jan 2012 00:06:21 +0000 (00:06 +0000)]
Fix RTP reference leak.
If a blind transfer were initiated using a REFER without a prior
reINVITE to place the call on hold, AND if Asterisk were sending
RTCP reports, then there was a reference for the RTP instance
of the transferer.
This fixes the issue by merging two similar but slightly conflicting
sections of code into a single area. It also adds a stop_media_flows()
call in the case that the transferer's UA never sends a BYE to us
like it is supposed to.
Matthew Jordan [Fri, 20 Jan 2012 15:54:32 +0000 (15:54 +0000)]
Remove unused variable 'tmp' from helpfun in ilbc codec
gcc version 4.6.2 caught an unused variable in the ilbc codec
library. This would prevent compilation with --enable-dev-mode;
variable removed.
........
Merged revisions 351760 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Richard Mudgett [Thu, 19 Jan 2012 23:25:05 +0000 (23:25 +0000)]
Misc minor fixes in reqresp_parser.c and chan_sip.c.
* Fix corner cases in get_calleridname() parsing and ensure that the
output buffer is nul terminated.
* Make get_calleridname() truncate the name it parses if the given buffer
is too small rather than abandoning the parse and not returning anything
for the name. Adjusted get_calleridname_test() unit test to handle the
truncation change.
* Fix get_in_brackets_test() unit test to check the results of
get_in_brackets() correctly.
* Fix parse_name_andor_addr() to not return the address of a local buffer.
This function is currently not used.
* Fix potential NULL pointer dereference in sip_sendtext().
* No need to memset(calleridname) in check_user_full() or tmp_name in
get_name_and_number() because get_calleridname() ensures that it is nul
terminated.
* Reply with an accurate response if get_msg_text() fails in
receive_message(). This is academic in v1.8 because get_msg_text() can
never fail.
........
Merged revisions 351618 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Kinsey Moore [Thu, 19 Jan 2012 22:43:35 +0000 (22:43 +0000)]
Correct output of RTCP jitter statistics in SR and RR reports
Change the RTCP RR and SR generation code to convert Asterisk's internal jitter
statistics to be represented in RTP timestamp units based on the rate of the
codec in use instead of in seconds.
(closes issue ASTERISK-14530)
........
Merged revisions 351611 from http://svn.asterisk.org/svn/asterisk/branches/1.8
Jonathan Rose [Thu, 19 Jan 2012 21:47:22 +0000 (21:47 +0000)]
Eliminates doubling the :port part of SIP Notify Message-Account headers.
This patch prevents the domain string from getting mangled during the initreqprep
step by moving the initialization to before its immediate use. It also documents
this pitfall for the ast_sockaddr_stringify functions.
projects / thirdparty / asterisk.git / log
