Tom Brouwer [Sun, 12 Jan 2020 12:13:30 +0000 (13:13 +0100)]
ipq40xx: add support for EZVIZ CS-W3-WD1200G EUP
Hardware:
SOC: Qualcomm IPQ4018
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MB Macronix MX25L12805D
ETH: Qualcomm QCA8075 (4 Gigabit ports, 3xLAN, 1xWAN)
WLAN: Qualcomm IPQ4018 (2.4 & 5 Ghz)
BUTTON: Shared WPS/Reset button
LED: RGB Status/Power LED
SERIAL: Header J8 (UART, Left side of board). Numbered from
top to bottom:
(1) GND, (2) TX, (3) RX, (4) VCC (White triangle
next to it).
3.3v, 115200, 8N1
Tested/Working:
* Ethernet
* WiFi (2.4 and 5GHz)
* Status LED
* Reset Button (See note below)
Implementation notes:
* The shared WPS/Reset button is implemented as a Reset button
* I could not find a original firmware image to reverse engineer, meaning
currently it's not possible to flash OpenWrt through the Web GUI.
Installation (Through Serial console & TFTP):
1. Set your PC to fixed IP 192.168.1.12, Netmask 255.255.255.0, and connect to
one of the LAN ports
2. Rename the initramfs image to 'C0A8010B.img' and enable a TFTP server on
your pc, to serve the image
2. Connect to the router through serial (See connection properties above)
3. Hit a key during startup, to pause startup
4. type `setenv serverip 192.168.1.12`, to set the tftp server address
5. type `tftpboot`, to load the image from the laptop through tftp
6. type `bootm` to run the loaded image from memory
6. (If you want to return to stock firmware later, create an full MTD backup,
e.g. using instructions here https://openwrt.org/docs/guide-user/installation/generic.backup#create_full_mtd_backup)
7. Transfer the 'sysupgrade' OpenWrt firmware image from PC to router, e.g.:
`scp xxx-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/upgrade.bin`
8. Run sysupgrade to permanently install OpenWrt to flash: `sysupgrade -n /tmp/upgrade.bin`
Revert to stock:
To revert to stock, you need the MTD backup from step 6 above:
1. Unpack the MTD backup archive
2. Transfer the 'firmware' partition image to the router (e.g. mtd8_firmware.backup)
3. On the router, do `mtd write mtd8_firmware.backup firmware`
Signed-off-by: Tom Brouwer <tombrouwer@outlook.com>
[removed BOARD_NAME, OpenWRT->OpenWrt, changed LED device name to board name] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ipq40xx: fix usbport trigger on the RT-AC58U with USB 2.0 devices
This patch partially reverts
"ipq40xx: remove unnecessary usb nodes in DTS for ASUS RT-AC58U"
as the change removed the usb2 port-trigger, so the LED would no
longer light-up when a USB 2.0 was inserted into the USB port.
Fixes: d0efb1ba95f3 ("ipq40xx: remove unnecessary usb nodes in DTS for ASUS RT-AC58U") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tobias Schramm [Tue, 3 Dec 2019 21:48:35 +0000 (22:48 +0100)]
ath79: add support for Ubiquiti ToughSwitch/EdgeSwitch 8XP
Flash: 8 MB
RAM: 64 MB
SoC: AR7242
Switch: bcm53128
USB: 1x USB 2.0
Ethernet: 8x GbE, 1x FE
The Ubiquiti ToughSwitch 8XP is a 8-port PoE Gigabit switch with a single
Fast-Ethernet management port. It supports both 24V passive PoE and 48V
802.11af/at PoE out on all eight ports.
By default the single Fast-Ethernet port labeled "MGMT" is configured as the
WAN port. Thus access to the device is only possible via the eight switch
ports.
Installation of the firware is possible either via serial + tftpboot or
the factory firmware update function via webinterface.
Serial: 3v3 115200 8n1
The serial header is located in the lower left corner of the switches PCB:
|
|
|
| o
| o RX
| o TX
| o GND
|
|
++ +-++-+ ++ ++ +
+--+ ++ +--++--++--+
Tobias Schramm [Tue, 3 Dec 2019 21:33:32 +0000 (22:33 +0100)]
firmware-utils: mkfwimage: add support for Ubiquiti SW devices
This commit adds support for Ubiquiti ToughSwitch XP (and probably also
EdgeSwitch XP) devices. They are mostly based on the same hardware as
MX devices.
Tobias Schramm [Tue, 3 Dec 2019 21:30:00 +0000 (22:30 +0100)]
swconfig: fix Broadcom b53 support
This commit fixes a bug in the main swconfig patch where a function
needed by the b53 driver is not exported.
Additionally it adds OF support to the b53_mdio driver for devicetree-
based probing
Keep up with a small amount of churn in the upstream repository.
Upstream now represents the version of CAKE as found in the linux kernel
from 4.19 onwards but with some compatibility stubs to allow building on
<4.19.
After a diversion related to an experimental ECN implementation which
has now been reverted, the important and relevant changes for us are:
8a8946b sch_cake: avoid possible divide by zero in cake_enqueue() 183b320 RFC 8622 diffserv3, 4 & 8 LE PHB support 6ff4561 sch_cake: Make sure we can write the IP header before changing DSCP bits 9fba602 sch_cake: Use tc_skb_protocol for getting packet protocol
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Chuanhong Guo [Wed, 8 Jan 2020 12:18:56 +0000 (20:18 +0800)]
ath79: gl-ar750s: reduce kernel size to 2M in image Makefile
u-boot splits nand factory firmware at 2M offset, flash the first
part as kernel into spi nor and the other part as ubi into nand
flash. With previous commit increasing kernel size to 4M, generated
factory firmware is broken because ubi is at 4M offset.
This commit reduces kernel size definition to 2M in image Makefile,
producing proper factory image. Partition size in dts is kept
unchanged so that sysupgrade to a firmware with 2M+ kernel still
works.
Fixes: b496a2294c ("ath79: GL-AR750S: provide NAND support; increase kernel to 4 MB") Reported-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* socket: mark skbs as not on list when receiving via gro
Certain drivers will pass gro skbs to udp, at which point the udp driver
simply iterates through them and passes them off to encap_rcv, which is
where we pick up. At the moment, we're not attempting to coalesce these
into bundles, but we also don't want to wind up having cascaded lists of
skbs treated separately. The right behavior here, then, is to just mark
each incoming one as not on a list. This can be seen in practice, for
example, with Qualcomm's rmnet_perf driver. This lead to crashes on
OnePlus devices and possibly other Qualcomm 4.14 devices. But I fear
that it could lead to issues on other drivers on weird OpenWRT routers.
Maxim Anisimov [Wed, 18 Dec 2019 06:52:44 +0000 (09:52 +0300)]
ramips: add support for TP-Link Archer C20 v5
TP-Link Archer C20 v5 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
Image (and we do not ship one with the image) we are not able to create
an image in the OpenWRT build-process.
Download a TP-Link image from their Website and a OpenWRT sysupgrade
image for the device and build yourself a factory image like following:
Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.
Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.
Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.
The boot.bin can now be uploaded and flashed using the web-recovery.
Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)
Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.
Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.
U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.
Dual U-Boot
-----------
This is TP-Link MediaTek device with a split-uboot feature design like
a TP-Link Archer C50 v4. The first (factory-uboot) provides recovery via
TFTP and HTTP, jumping straight into the second (firmware-uboot) if no
recovery needs to be performed. The firmware-uboot unpacks and executed
the kernel.
Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5 / Archer C50v4. Stock-firmware sets a flag in the "romfile"
partition before beginning to write and removes it afterwards. If the
router boots with this flag set, bootloader will automatically start
Web-recovery and listens on 192.168.0.1. This way, the vendor-firmware
or an OpenWRT factory image can be written.
By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.
It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[adjust some node names for LEDs in DTS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Daniel Golle [Thu, 9 Jan 2020 13:32:12 +0000 (15:32 +0200)]
dnsmasq: add uci-defaults script for config migration
When running sysupgrade from an existing configuration, UCI option
dhcp.@dnsmasq[0].resolvfile needs to be modified in case it has not
been changed from it's original value.
Accomplish that using a uci-defaults script.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
David Bauer [Thu, 9 Jan 2020 11:32:16 +0000 (12:32 +0100)]
ramips: disable image build for HiWiFi HC5962
Image builds for the ramips-mt7621 target currently fail with:
> WARNING: Image file ./hiwifi_hc5962-kernel.bin is too big
Disable this board for now. It can still be built using the SDK.
David Bauer [Sun, 5 Jan 2020 23:13:58 +0000 (00:13 +0100)]
hostapd: disable ft_psk_generate_local for non-PSK networks
Without this commit, ft_psk_generate_local is enabled for non-PSK
networks by default. This breaks 802.11r for EAP networks.
Disable ft_psk_generate_local by default for non-PSK networks resolves
this misbehavior.
Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net> Signed-off-by: David Bauer <mail@david-bauer.net> Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
This target is still on kernel 4.9, and it looks like there is no
active maintainer for this target anymore.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target seems to have been unmaintained for quite a while, and not a
single tester for the (now outdated) kernel 4.14 patches has been found.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target seems to have been unmaintained for quite a while, and not a
single tester for the (now outdated) kernel 4.14 patches has been found.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hauke Mehrtens [Sat, 11 May 2019 11:51:08 +0000 (13:51 +0200)]
orion: update kernel to version 4.14
This adds support for kernel 4.14 to the target and directly make it the
default kernel version to use.
This patch is build-tested only, but has never been device-tested. It is
only added to preserve the changes in Git history prior to removing this
target. Use it with care.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[rebased and extended commit message, refreshed patches for 4.14.162] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hauke Mehrtens [Sat, 11 May 2019 11:47:37 +0000 (13:47 +0200)]
ar7: update kernel to version 4.14
This adds support for kernel 4.14 to the target and directly make it the
default kernel version to use.
This patch is build-tested only, but has never been device-tested. It is
only added to preserve the changes in Git history prior to removing this
target. Use it with care.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[rebased and extended commit message, refreshed patches for 4.14.162] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
treewide: move mktplinkfw to tplink-v1-image in image-commands.mk
This move the slightly different target-specific implementations of
mktplinkfw from the targets to include/image-commands.mk and renames
it to tplink-v1-image. Having a common version will increase
consistency between implementation and will complete the
tplink build command already present in the new location.
Due to the slight differences of the original implementations, this
also does some adjustments to the device build commands/variables.
This also moves rootfs_align as this is required as dependency.
Tested on:
- TL-WDR4300 v1 (ath79, factory)
- TL-WDR4900 v1 (mpc85xx, sysupgrade)
- RE210 v1 (ramips, see Tested-by)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Christoph Krapp <achterin@googlemail.com>
Ansuel Smith [Sun, 5 Jan 2020 17:15:22 +0000 (18:15 +0100)]
ipq806x: refactor l2 freq scaling patch
Refactor l2 freq scaling patch to support voltage
scaling and add support to base cache scaling on
cpu freq scaling. Update the dtsi files with the new
definition used in the new code.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Ansuel Smith [Wed, 25 Dec 2019 19:44:06 +0000 (20:44 +0100)]
ipq806x: reorganize nand_pins mux definition
It's wrong set the mux to bias-disable. The best way to
do this is by creating a separate group and disable the
specific pins.
By documentation, any subgroup with no bias definition
is ignored so the mux definition is useless.
Rework the definition by sremoving the mux subgroup and
set the remaining subgroup with the mux function and
drive-strength
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Ansuel Smith [Wed, 25 Dec 2019 18:42:08 +0000 (19:42 +0100)]
ipq806x: opp/core: fix broken patch Handle opp voltage adjust
The opp_notifier introduced with patch 0054-Handle-OPP-voltage adjust
for some reason missed the actual registration in the opp struct,
resulting in never being registred.
This was present in kernel 4.9 patchset but dropped in the transition
to 4.14. Reintroduce this and fix patch 0055 about L2 cache scaling.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Hauke Mehrtens [Mon, 6 Jan 2020 15:21:25 +0000 (16:21 +0100)]
dnsmasq: Fix potential dnsmasq crash with TCP
This is a backport from the dnsmasq master which should fix a bug which
could cause a crash in dnsmasq.
I saw the following crashes in my log:
[522413.117215] do_page_fault(): sending SIGSEGV to dnsmasq for invalid read access from 2a001450
[522413.124464] epc = 004197f1 in dnsmasq[400000+23000]
[522413.129459] ra = 004197ef in dnsmasq[400000+23000]
This is happening in blockdata_write() when block->next is
dereferenced, but I am not sure if this is related to this problem or if
this is a different problem. I am unable to reproduce this problem.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Yong-hyu Ban <perillamint@quendi.moe>
[do not enable xhci node in DTS which is already enabled in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Mason Clarke [Sun, 29 Dec 2019 18:03:00 +0000 (19:03 +0100)]
ramips: reduce lzma dictionary size for D-Link DIR-645
Currently this device fails to boot with the OpenWrt snapshot images
(release images are unaffected). The error message is:
"LZMA ERROR 1 - must RESET board to recover".
This happens because the kernel image is too big for the bootloader
to boot. This commit works around this by decreasing the lzma dictionary
size option from the default 23 to 10.
Before this change the current OpenWrt snapshot image (uncompressed
kernel size 4875139 bytes) failed to boot, while now an even bigger
image (kernel 4.19 with snapshot default config; uncompressed kernel
size 5162833 bytes) boots just fine.
The highest lzma dictionary size option this image booted with was 11.
10 was chosen to have a bit more room for growth.
An unavoidable side-effect of this change is that the compressed kernel
image will take up more space.
DENG Qingfang [Wed, 1 Jan 2020 07:23:32 +0000 (15:23 +0800)]
pppd: update to 2.4.8
78cd384 Update README and patchlevel.h for 2.4.8 release 5d03403 pppd: Avoid use of strnlen (and strlen) in vslprintf a1e950a pppd: Fix IPv6 default route code for Solaris ca5e61b plugins/rp-pppoe: Make tag parsing loop condition more accurate c10c3c7 pppd: Make sure word read from options file is null-terminated b311e98 pppd: Limit memory accessed by string formats with max length specified 3ea9de9 pppd: Eliminate some more compiler warnings 57edb1a pppd: Include time.h header before using time_t 09f695f pppd: Don't free static string 03104ba pppd.h: Add missing headers 388597e pppd: Add defaultroute6 and related options 66ce4ba pppd: Avoid declarations within statements in main.c 5637180 pppd: Fix `ifname` option in case of multilink (#105) d00f8a0 pppd: Fix variable reference syntax in Makefile.linux b6b4d28 pppd: Check tdb pointer before closing
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Christoph Krapp [Thu, 2 Jan 2020 09:30:37 +0000 (10:30 +0100)]
ath79: use ath10k-ct-smallbuffers for TP-Link RE355/RE450 v1
Both devices are available in 64M and 128M RAM configurations but there
is no visial indication which configuration one might get.
So just to be sure we properly support both configurations switch to
kmod-atk10k-ct-smallbuffers.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
Rosen Penev [Sat, 4 Jan 2020 02:31:01 +0000 (18:31 -0800)]
libcxx: Remove -flto from LDFLAGS
It seems the buildbots can't handle it.
Added a cmake option to find the cxxabi files as they are part of the
toolchain and not in the normal path. It doesn't seem to make a
difference, just gets rid of cmake warnings.
Added another small GCC warning fix. It's fairly minor.
This has no change in compiled size, and most likely no change in
behavior. Bumped the PKG_RELEASE anyway.
ath79: Remove mtd cfi_cmdset_0002 status check patches
Currently the patch only changes break to use goto statement instead.
But not necessary acutually since the ret value checked after the for loop.
So it is okay for the break case before changed by the patch also.
This patch only reverts the following commit partially.
https://github.com/openwrt/openwrt/commit/ddc11c3932c7b7b7df7d5fbd48f207e7
Note: The changes are mainly applied into the linux kernel upstream.
ar71xx: Remove mtd cfi_cmdset_0002 status check patch
Currently the patch only changes break to use goto statement instead.
But not necessary acutually since the ret value checked after the for loop.
So it is okay for the break case before changed by the patch also.
This patch only reverts the following commit partially.
https://github.com/openwrt/openwrt/commit/ddc11c3932c7b7b7df7d5fbd48f207e77619eaa7
Note: The changes are mainly applied into the linux kernel upstream.
These two hacks are no longer necessary as they've
been moved to a special variant of kmod-ath10k-ct.
So, if you have a device suffering from low-memory
situation and getting applications crashes due to
the OOM reaper or kernel panics with ath10k, please
use the "kmod-ath10k-ct-smallbuffers" package from
now on.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Petr Štetiar [Tue, 31 Dec 2019 09:34:29 +0000 (10:34 +0100)]
base-files: sysupgrade: exit if the firmware download failed
Sysupgrade process shouldn't continue if the firmware image couldn't be
downloaded.
Ref: http://lists.infradead.org/pipermail/openwrt-devel/2019-December/020940.html Reported-by: Petr Novák <petrn@me.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hauke Mehrtens [Sat, 4 Jan 2020 22:45:20 +0000 (23:45 +0100)]
kernel: bump 4.19 to 4.19.93
Refreshed all patches.
The patch hack-4.19/550-loop-better-discard-for-block-devices.patch was
replaced with an new version of the patch from:
https://lore.kernel.org/patchwork/patch/1153625/
https://lore.kernel.org/patchwork/patch/1153626/
Compile-tested on: ipq40xx, lantiq
Runtime-tested on: ipq40xx, lantiq
Maksym Medvedev [Fri, 15 Nov 2019 22:21:22 +0000 (23:21 +0100)]
ramips: add support for Edimax RA21S
Edimax RA21S is a dual band 11ac router,
based on MediaTek MT7621A and MT7615N chips.
Specification:
- SoC: MediaTek MT7621A dual-core @ 880MHz
- RAM: 256M (Nanya NT5CC128M16IP)
- FLASH: 16MB (Macronix MX25L12835F)
- WiFi: 2.4/5 GHz 4T4R
- 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
- USB: No
- BTN: Reset, WPS
- LED: 4 red LEDs, indistinguishable when case closed
- UART: through-hole on PCB.
J1: 3.3V - RX - GND - TX / 57600-8N1. 3.3V is the square pad
Installation:
Update the factory image via the OEM web-interface
(by default: http://192.168.2.1/)
User: admin
Password: 1234
The sysupgrade image can be installed via TFTP
from the U-Boot bootloader. Connect via ethernet port 2.
Tested on device by @UAb5eSMn
Signed-off-by: Maksym Medvedev <redrathnure@gmail.com>
[split DTS and take over improvements from RG21S, extend commit
message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Daniel Golle [Sat, 4 Jan 2020 09:47:50 +0000 (11:47 +0200)]
generic: fix compiler error in OpenWrt's kexec patch
330-MIPS-kexec-Accept-command-line-parameters-from-users.patch causes
problems when building with -Werror=unused-result.
arch/mips/kernel/machine_kexec.c: In function 'machine_kexec_init_argv':
arch/mips/kernel/machine_kexec.c:76:2: error: ignoring return value of 'copy_from_user', declared with attribute warn_unused_result [-Werror=unused-result]
copy_from_user(kexec_argv_buf, buf, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fix this by handling the return value in an appropriate way.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CONFIG_PINCTRL_SUN4I_A10 controls both the A10 and the A20 enablong of
the pinctrl driver, this is necessary since upstream commit 5d8d349618a9464714c07414c5888bfd9416638f ("pinctrl: sunxi: add A20
support to A10 driver") which has been included in v4.13 and onwards.
Fixes: ad2b3bf310f7 ("sunxi: Add support for kernel 4.14") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Shared base-files package contains functions for LED migration that
are already used by several targets. Apply those also to lantiq and
drop the (redundant) local code.
While at it, reorder board names in file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The only device in samsung target is meant to be built with s5pv210
subtarget. Thus, though this won't make a difference for a
one-subtarget target, already add the condition to the Makefile to
make the assignment obvious.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
samsung: use soc_vendor_model scheme for DTS file name
This patch changes the samsung target to calculate the DTS file name
from vendor and device name and the SOC (i.e. subtarget) following
the common scheme:
soc_vendor_model.dts
This also updates the device definition name to make compatible,
image name, menuconfig name and DTS name consistent.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
David Bauer [Thu, 2 Jan 2020 18:25:26 +0000 (19:25 +0100)]
ramips: fix Archer C2 v1 5GHz MAC address
The TP-Link Archer C2 v1 previously had a generic Ralink MAC address set
for the 5GHz radio (MT7610), as the caldata does only contain a generic
MAC address.
Set the MAC address from the vendor firmware for the 5GHz radio to
assign unique MAC addresses to every device.
David Bauer [Thu, 2 Jan 2020 02:11:39 +0000 (03:11 +0100)]
ramips: convert TP-Link MT7620 boards to tpt trigger
This converts all MediaTek MT7620 boards from TP-Link to use the now
supported WiFi throughput LED trigger. This way, the LED state now
covers all VAPs regardless of their name.
Also align all single-WiFi LEDs to represent the state of the 2.4GHz
radio. This was not always the case previously, as later-added support
for the MT7610 altered the phy probing order.
projects / thirdparty / openwrt.git / log
