platform/x86: hp-wmi: Add support for Omen 16-wf1xxx (8C77)
The HP Omen 16-wf1xxx (board ID: 8C77) has the same WMI interface as
other Victus S boards, but requires quirks for correctly switching
thermal profile.
Add the DMI board name to victus_s_thermal_profile_boards[] table and
map it to omen_v1_thermal_params.
Testing on board 8C77 confirmed that platform profile is registered
successfully and fan RPMs are readable and controllable.
Tested-by: Thomas Arici <absolute3d86@gmail.com> Reported-by: Thomas Arici <absolute3d86@gmail.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221300 Signed-off-by: Krishna Chomal <krishna.chomal108@gmail.com> Link: https://patch.msgid.link/20260410191039.125659-5-krishna.chomal108@gmail.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: hp-wmi: Add support for Omen 16-n0xxx (8A44)
The HP Omen 16-n0xxx (board ID: 8A44) has the same WMI interface as
other Victus S boards, but requires quirks for correctly switching
thermal profile.
Add the DMI board name to victus_s_thermal_profile_boards[] table and
map it to omen_v1_legacy_thermal_params.
Testing on board 8A44 confirmed that platform profile is registered
successfully and fan RPMs are readable and controllable.
Tested-by: Prasoon Dev <prasoon5050@outlook.com> Signed-off-by: Krishna Chomal <krishna.chomal108@gmail.com> Link: https://patch.msgid.link/20260410191039.125659-4-krishna.chomal108@gmail.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: hp-wmi: Add support for OMEN MAX 16-ak0xxx (8D87)
The HP OMEN MAX 16-ak0xxx (8D87) requires the same WMI queries as other
Victus S devices, hence it has been added to the corresponding list.
For this reason, platform_profile_victus_s_get_ec() will be called
during thermal_profile_setup() and victus_s_powersource_event() to
obtain hardware state (platform profile) by reading from the Embedded
Controller, however, this particular board's EC does not seem to expose
the platform profile value, unlike other boards. Hence EC readback is
disabled.
Testing on board 8D87 confirmed that platform profile is registered
successfully and fan RPMs are readable and controllable.
Tested-by: Jinyang Zhu <Jakie101@proton.me> Signed-off-by: Krishna Chomal <krishna.chomal108@gmail.com> Link: https://patch.msgid.link/20260410191039.125659-3-krishna.chomal108@gmail.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
For Victus S devices, the BIOS fan table header was being incorrectly
parsed as:
struct {
u8 unknown;
u8 num_entries;
}
The first field should be num_fans and the second should be unknown. It
is pure coincidence that interpreting an "unknown" field as "num_entries"
worked on multiple device, however for board 8D87 (in an upcoming patch),
this assumption fails, and the hp-wmi driver fails to load.
We fix this by correcting the header definition and compensating for
num_entries by parsing each entry of the fan table until an all-NULL row
is obtained, mirroring the behavior of OMEN Gaming Hub on Windows.
Fixes: 46be1453e6e6 ("platform/x86: hp-wmi: add manual fan control for Victus S models") Signed-off-by: Krishna Chomal <krishna.chomal108@gmail.com> Link: https://patch.msgid.link/20260410191039.125659-2-krishna.chomal108@gmail.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: hp-wmi: add Omen 14-fb0xxx (board 8C58) support
Board 8C58 (HP Omen Transcend Gaming Laptop 14-fb0xxx) appears to use
the same thermal profile handling as other supported Omen systems,
including board 8E41.
Add it to omen_thermal_profile_boards so hp-wmi can expose the firmware
thermal profiles through the platform_profile interface.
Tested on Omen 14-fb0xxx: the profile handler exposes cool, balanced,
and performance modes, and selecting performance increases sustained CPU
package power under load.
Armin Wolf [Mon, 6 Apr 2026 20:32:37 +0000 (22:32 +0200)]
platform/wmi: Replace .no_notify_data with .min_event_size
WMI drivers using the buffer-based WMI API are expected to reject
undersized event payloads. Extend the WMI driver core to allow
such drivers to specify their minimum supported event payload size.
Also remove the now redundant .no_notify_data field.
Armin Wolf [Mon, 6 Apr 2026 20:32:36 +0000 (22:32 +0200)]
platform/wmi: Extend wmidev_query_block() to reject undersized data
WMI drivers using the buffer-based WMI API are expected to reject
undersized query results. Extend wmidev_query_block() to enable
the WMI driver core to perform this size check internally.
Armin Wolf [Mon, 6 Apr 2026 20:32:35 +0000 (22:32 +0200)]
platform/wmi: Extend wmidev_invoke_method() to reject undersized data
WMI drivers using the buffer-based WMI API are expected to reject
undersized method return values. Extend wmidev_invoke_method() to
enable the WMI driver core to perform this size check internally.
Armin Wolf [Mon, 6 Apr 2026 20:32:34 +0000 (22:32 +0200)]
platform/wmi: Prepare to reject undersized unmarshalling results
Driver using the buffer-based WMI API usually reject buffers resulting
from WMI method calls or block queries if they contain not enough data.
Prepare the WMI core for assisting in this by automatically rejecting
undersized unmarshalling results.
Armin Wolf [Mon, 6 Apr 2026 20:32:32 +0000 (22:32 +0200)]
platform/wmi: Add wmidev_invoke_procedure()
Some WMI methods return no values, so the whole postprocessing
of the result data is not needed for them. Add a special function
for calling such WMI methods to prepare for future changes of
the main wmidev_invoke_method() function.
platform/x86: int3472: Add support for GPIO type 0x02 (IR flood LED)
Add support for GPIO type 0x02, which controls an IR flood LED used
for face authentication on some laptops (e.g. Dell Pro Max 16 Premium).
Without this patch, the kernel logs "GPIO type 0x02 unknown; the sensor
may not work" and IR sensors paired with a flood LED cannot function.
The flood LED is registered through the LED subsystem like the existing
privacy LED, including a lookup entry to allow future consumer drivers
to find and control it via led_get().
To support multiple LEDs per INT3472 device, convert the single led
struct member to an array with a counter.
Signed-off-by: Marco Nenciarini <mnencia@kcore.it> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com> Link: https://patch.msgid.link/20260401203638.1601661-5-mnencia@kcore.it Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: int3472: Parameterize LED con_id in registration
Add a con_id parameter to skl_int3472_register_led() to allow callers
to specify both the LED name suffix and lookup con_id instead of
hardcoding "privacy". This prepares for registering additional LED
types with different names.
While at it, rename the privacy LED's GPIO con_id from "privacy-led"
to "privacy" in int3472_get_con_id_and_polarity() and pass it
directly to skl_int3472_register_led(), reducing churn when adding
new LED types.
No functional change.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com> Signed-off-by: Marco Nenciarini <mnencia@kcore.it> Link: https://patch.msgid.link/20260401203638.1601661-4-mnencia@kcore.it Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: int3472: Rename pled to led in LED registration code
Rename the privacy LED type, struct member, and functions from "pled"
to "led" in preparation for supporting additional LED types beyond
just the privacy LED.
No functional change.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com> Signed-off-by: Marco Nenciarini <mnencia@kcore.it> Link: https://patch.msgid.link/20260401203638.1601661-3-mnencia@kcore.it Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: int3472: Use local variable for LED struct access
Introduce a local struct int3472_pled pointer in the LED registration,
unregistration, and brightness callback functions to avoid repeatedly
dereferencing int3472->pled. In the brightness callback, use
container_of() to get the int3472_pled struct directly instead of
going through int3472_discrete_device.
No functional change.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com> Signed-off-by: Marco Nenciarini <mnencia@kcore.it> Link: https://patch.msgid.link/20260401203638.1601661-2-mnencia@kcore.it Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Daniil Bulgar [Tue, 7 Apr 2026 19:05:46 +0000 (21:05 +0200)]
platform/x86: thinkpad_acpi: remove obsolete TODO comment
This patch removes the obsolete TODO comment regarding fan speed
presets in fan_write_cmd_speed. After discussion with the
maintainers, it was decided that fixed presets (low/medium/high)
are not suitable due to platform-specific variations.
Signed-off-by: Daniil Bulgar <bulgardaniil18@gmail.com> Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca> Link: https://patch.msgid.link/20260407190546.109900-1-bulgardaniil18@gmail.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
populate_enum_data() aggregates firmware-provided value-modifier
and possible-value strings into fixed 512-byte struct members.
The current code bounds each individual source string but then
appends every string and separator with raw strcat() and no
remaining-space check.
Switch the aggregation loops to a bounded append helper and
reject enumeration packages whose combined strings do not fit
in the destination buffers.
Fixes: e8a60aa7404b ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn> Link: https://patch.msgid.link/20260408084501.1-dell-wmi-sysman-v2-pengpeng@iscas.ac.cn
[ij: add include] Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: hp-wmi: Ignore backlight and FnLock events
On HP OmniBook 7 the keyboard backlight and FnLock keys are handled
directly by the firmware. However, they still trigger WMI events which
results in "Unknown key code" warnings in dmesg.
Add these key codes to the keymap with KE_IGNORE to silence the warnings
since no software action is needed.
Tested-by: Artem S. Tashkinov <aros@gmx.com> Reported-by: Artem S. Tashkinov <aros@gmx.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221181 Signed-off-by: Krishna Chomal <krishna.chomal108@gmail.com> Link: https://patch.msgid.link/20260403080155.169653-1-krishna.chomal108@gmail.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The function sysfs_match_string() can return negative error codes and
the variable assigned to it is the enum 'option'. Which could be an
unsigned int due to different compiler implementations.
Assign signed variable 'ret' to sysfs_match_string(), check for error,
then assign ret to option.
Detected by Smatch:
drivers/platform/x86/uniwill/uniwill-acpi.c:919 usb_c_power_priority_store()
warn: unsigned 'option' is never less than zero.
Fixes: 03ae0a0d0973b ("platform/x86: uniwill-laptop: Implement USB-C power priority setting") Signed-off-by: Ethan Tidmore <ethantidmore06@gmail.com> Link: https://patch.msgid.link/20260403070928.802196-1-ethantidmore06@gmail.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: dell_rbu: avoid uninit value usage in packet_size_write()
Ensure the temp value has been properly parsed from the user-provided
buffer and initialized to be used in later operations. While at it,
prefer a convenient kstrtoul() helper.
Found by Linux Verification Center (linuxtesting.org) with Svace static
analysis tool.
Fixes: ad6ce87e5bd4 ("[PATCH] dell_rbu: changes in packet update mechanism") Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Link: https://patch.msgid.link/20260403134240.604837-1-pchelkin@ispras.ru
[ij: add include] Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: hp-wmi: add locking for concurrent hwmon access
hp_wmi_hwmon_priv.mode and .pwm are written by hp_wmi_hwmon_write() in
sysfs context and read by hp_wmi_hwmon_keep_alive_handler() in a
workqueue. A concurrent write and keep-alive expiry can observe an
inconsistent mode/pwm pair (e.g. mode=MANUAL with a stale pwm).
Add a mutex to hp_wmi_hwmon_priv protecting mode and pwm. Hold it in
hp_wmi_hwmon_write() across the field update and apply call, and in
hp_wmi_hwmon_keep_alive_handler() before calling apply.
In hp_wmi_hwmon_read(), only the pwm_enable path reads priv->mode; use
scoped_guard() there to avoid holding the lock across unrelated WMI
calls.
Fixes: c203c59fb5de ("platform/x86: hp-wmi: implement fan keep-alive") Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Emre Cecanpunar <emreleno@gmail.com> Link: https://patch.msgid.link/20260407142515.20683-6-emreleno@gmail.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: hp-wmi: fix u8 underflow in gpu_delta calculation
gpu_delta was declared as u8. If the firmware specifies a GPU RPM
lower than the CPU RPM, subtracting them causes an underflow
(e.g. 10 - 20 = 246), which forces the GPU fan to remain clamped at
U8_MAX (100% speed) during operation.
Change gpu_delta to int and use signed arithmetic. Existing signed logic
in hp_wmi_fan_speed_set() correctly handles negative deltas.
Fixes: 46be1453e6e6 ("platform/x86: hp-wmi: add manual fan control for Victus S models") Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Emre Cecanpunar <emreleno@gmail.com> Link: https://patch.msgid.link/20260407142515.20683-5-emreleno@gmail.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: hp-wmi: use mod_delayed_work to reset keep-alive timer
Currently, schedule_delayed_work() is used to queue the 90s keep-alive
timer. If a user manually changes the fan speed at T=85s,
schedule_delayed_work() leaves the existing timer in place as it is a
no-op if the work is already pending. This results in the keep-alive
timer firing unnecessarily at T=90s, just 5 seconds after the user
action.
Replace schedule_delayed_work() with mod_delayed_work() to reset the
90s timer whenever fan settings are applied. This guarantees a full 90s
delay after every user interaction, preventing redundant keep-alive
executions and improving efficiency.
Fixes: c203c59fb5de ("platform/x86: hp-wmi: implement fan keep-alive") Signed-off-by: Emre Cecanpunar <emreleno@gmail.com> Link: https://patch.msgid.link/20260407142515.20683-4-emreleno@gmail.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: hp-wmi: avoid cancel_delayed_work_sync from work handler
hp_wmi_apply_fan_settings() uses cancel_delayed_work_sync() to stop
the keep-alive timer in AUTO mode. However, since
hp_wmi_apply_fan_settings() is also called from the keep-alive
handler, a race condition with a sysfs write can cause the handler to
wait on itself, leading to a deadlock.
Replace cancel_delayed_work_sync() with cancel_delayed_work() in
hp_wmi_apply_fan_settings() to avoid the self-flush deadlock.
Fixes: c203c59fb5de ("platform/x86: hp-wmi: implement fan keep-alive") Signed-off-by: Emre Cecanpunar <emreleno@gmail.com> Link: https://patch.msgid.link/20260407142515.20683-3-emreleno@gmail.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: hp-wmi: fix ignored return values in fan settings
hp_wmi_get_fan_count_userdefine_trigger() can fail, but its return
value was silently ignored in hp_wmi_apply_fan_settings() for
PWM_MODE_MAX/AUTO. Propagate these errors consistently.
Additionally, handle the return value of hp_wmi_apply_fan_settings()
in its callers by adding appropriate warnings on failure, and remove an
unreachable "return 0" at the end of the function.
Fixes: 46be1453e6e6 ("platform/x86: hp-wmi: add manual fan control for Victus S models") Signed-off-by: Emre Cecanpunar <emreleno@gmail.com> Link: https://patch.msgid.link/20260407142515.20683-2-emreleno@gmail.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Thorsten Blum [Tue, 31 Mar 2026 16:03:11 +0000 (18:03 +0200)]
platform/x86: dell-wmi-sysman: Clean up security buffer helpers
In calculate_security_buffer(), call strlen() once and use ALIGN() to
round up to an even size.
In populate_security_buffer(), also avoid recomputing strlen(), rename
the u32 pointer from 'seclen' to 'seclenp' to avoid confusion with the
new length variable, and drop the memcpy() guard since calling it with
size 0 is a no-op and therefore safe.
Use 'const char *' for the read-only source string in both helpers.
platform/x86: thinkpad_acpi: Drop ACPI driver registration
There is no point in registering an ACPI driver that only has an empty
.add() callback, which is done by the thinkpad_acpi driver, since
after binding to an ACPI device it only sits there and does nothing.
That binding only effectively causes the ACPI device's reference count
to increase, but that can be achieved by using acpi_get_acpi_dev()
instead of acpi_fetch_acpi_dev() in setup_acpi_notify(), and doing
the corresponding cleanup in ibm_exit().
Update the code accordingly and get rid of the non-functional ACPI
driver.
No intentional functional impact beyond altering sysfs content.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca> Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca> Link: https://patch.msgid.link/3949487.kQq0lBPeGt@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: asus-wireless: Convert ACPI driver to a platform one
In all cases in which a struct acpi_driver is used for binding a driver
to an ACPI device object, a corresponding platform device is created by
the ACPI core and that device is regarded as a proper representation of
underlying hardware. Accordingly, a struct platform_driver should be
used by driver code to bind to that device. There are multiple reasons
why drivers should not bind directly to ACPI device objects [1].
Overall, it is better to bind drivers to platform devices than to their
ACPI companions, so convert the Asus wireless ACPI driver to a platform
one.
After this change, the subordinate input and LED devices will be
registered under the platform device used for driver binding instead of
its ACPI companion.
While this is not expected to alter functionality, it changes sysfs
layout and so it will be visible to user space.
To facilitate subsequent conversion of the driver to a platform one,
make it install an ACPI notify handler directly instead of using
a .notify() callback in struct acpi_driver.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Denis Benato <denis.benato@linux.dev> Link: https://patch.msgid.link/1949745.tdWV9SEqCh@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: asus-laptop: Convert ACPI driver to a platform one
In all cases in which a struct acpi_driver is used for binding a driver
to an ACPI device object, a corresponding platform device is created by
the ACPI core and that device is regarded as a proper representation of
underlying hardware. Accordingly, a struct platform_driver should be
used by driver code to bind to that device. There are multiple reasons
why drivers should not bind directly to ACPI device objects [1].
Overall, it is better to bind drivers to platform devices than to their
ACPI companions, so convert the Asus laptop ACPI driver to a platform
one.
While this is not expected to alter functionality, it changes sysfs
layout and so it will be visible to user space.
To facilitate subsequent conversion of the driver to a platform one,
make it install an ACPI notify handler directly instead of using
a .notify() callback in struct acpi_driver.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Denis Benato <denis.benato@linux.dev> Link: https://patch.msgid.link/5082508.31r3eYUQgx@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
This version includes the following changes:
- Setting current base frequency as maximum for SST-BF with
kernel QOS changes
- Harmonize extended family decoded with the rest of the kernel
- Minor changes for error codes and messages
Zhang Rui [Thu, 19 Mar 2026 05:52:56 +0000 (13:52 +0800)]
tools/power/x86/intel-speed-select: Fix output when running on unsupported CLX platforms
When running intel-speed-select on unsupported CLX platforms, it prints
intel-speed-select: Invalid CPU model (85)
: Success
Because this is not a system error and errno is not set.
Zhang Rui [Thu, 19 Mar 2026 05:52:55 +0000 (13:52 +0800)]
tools/power/x86/intel-speed-select: Print Version info when Incompatible API version is detected
When running an old version intel-speed-select tool on newer platforms,
even with "intel-speed-select -v", the tool only complains about
"Incompatible API version", without giving the current version info.
Print Version info whenever Incompatible API version is detected.
Zhang Rui [Thu, 19 Mar 2026 05:52:54 +0000 (13:52 +0800)]
tools/power/x86/intel-speed-select: Fix some program return value
When running the "intel-speed-select -h" command, it returns
1. 0 when using a version that is API incompatible.
2. 1 when using a version that is API compatible.
And this is confusing.
Fix the program to return 0 for "-h" parameter, and return 1 whenever
"Incompatible API versions" is detected.
Zhang Rui [Mon, 26 Jan 2026 00:27:01 +0000 (08:27 +0800)]
tools/power/x86/intel-speed-select: Fix cpu extended family ID decoding
When decode and use CPU extended family ID in intel-speed-select, there
are several potential issues,
1. Mask with 0x0f to get CPU extended family ID is bogus because
CPU extended family ID takes 8 bits (bit 27:20).
2. Use CPU extended family ID fields without checking CPU family ID is
risky. Because Intel SDM says, "The Extended Family ID needs to be
examined only when the Family ID is 0FH."
3. Saving cpu family ID and cpu extended family ID separately doesn't
align with Linux kernel. And it may bring extra complexity when
making family specific changes in the future.
tools/power/x86/intel-speed-select: Avoid current base freq as maximum
SST-PP level change results in online/offline of CPUs with -o option.
The Linux intel-pstate driver internally stores the current HWP_REQ MSR
value during offline and restores them during online.
It is possible that during SST-PP level change, the new HWP_CAP limits
can be updated. So, when a CPU is online, the HWP_REQ MSR should be
updated to new values based on HWP_CAP values.
This is particularly problematic when either turbo is disabled or the
current HWP_REQ value (stored before online) is less than the base
frequency from the updated HWP_CAP MSR guaranteed value. If the HWP_REQ
MSR is not updated, then the performance will be limited to the value
before perf level change.
Hence the tool updates cpufreq scaling_max_freq to the newer
base_frequency value in this case. This step is not required when HWP
interrupts are enabled, as the perf level change should result in a new
interrupt with HWP_GUARANTEED_PERF_CHANGE_STATUS and the intel_pstate
driver will update to new limits.
But the tool needs to handle the case when HWP interrupts are not
enabled but there is no way for the tool to know that HWP interrupts are
enabled or not. So, it has to still update the scaling_max_freq.
With the QOS changes in the kernel, user space writes to scaling_max_freq
are treated as hard limits. So, when base frequency is increased with
SST-BF enabled, the cpufreq subsystem will still not allow setting to the
SST-BF high priority core frequency. So, the HWP_REQ MSR will still be
capped to the user-set scaling_max_freq after SST-PP level change.
To address this, instead of setting scaling_max_freq to the current HWP_CAP
highest frequency, set it to the maximum integer value to set the QOS limit
as unconstrained. In this case, the actual HWP_REQ maximum frequency will
still be capped to HWP_CAP highest performance by the intel-pstate driver.
So, it will not result in invalid HWP_REQ values.
platform/x86: toshiba_haps: Convert ACPI driver to a platform one
In all cases in which a struct acpi_driver is used for binding a driver
to an ACPI device object, a corresponding platform device is created by
the ACPI core and that device is regarded as a proper representation of
underlying hardware. Accordingly, a struct platform_driver should be
used by driver code to bind to that device. There are multiple reasons
why drivers should not bind directly to ACPI device objects [1].
Overall, it is better to bind drivers to platform devices than to their
ACPI companions, so convert the Toshiba HDD Active Protection Sensor
driver from an ACPI driver to a platform one.
While this is not expected to alter functionality, it changes sysfs
layout and so it will be visible to user space.
Note that the sysfs attributes in haps_attr_group will still be there
in the sysfs directory of the ACPI companion of the platform device
used for driver binding in case there are tools in user space expecting
them to be present there.
To facilitate subsequent conversion of the driver to a platform one,
make it install an ACPI notify handler directly instead of using
a .notify() callback in struct acpi_driver.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/10834562.nUPlyArG6x@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: toshiba_bluetooth: Convert ACPI driver to a platform one
In all cases in which a struct acpi_driver is used for binding a driver
to an ACPI device object, a corresponding platform device is created by
the ACPI core and that device is regarded as a proper representation of
underlying hardware. Accordingly, a struct platform_driver should be
used by driver code to bind to that device. There are multiple reasons
why drivers should not bind directly to ACPI device objects [1].
Overall, it is better to bind drivers to platform devices than to their
ACPI companions, so convert the Toshiba Bluetooth Enable driver from an
ACPI driver to a platform one.
While this is not expected to alter functionality, it changes sysfs
layout and so it will be visible to user space.
To facilitate subsequent conversion of the driver to a platform one,
make it install an ACPI notify handler directly instead of using
a .notify() callback in struct acpi_driver.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/3048289.e9J7NaK4W3@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: toshiba_acpi: Convert ACPI driver to a platform one
In all cases in which a struct acpi_driver is used for binding a driver
to an ACPI device object, a corresponding platform device is created by
the ACPI core and that device is regarded as a proper representation of
underlying hardware. Accordingly, a struct platform_driver should be
used by driver code to bind to that device. There are multiple reasons
why drivers should not bind directly to ACPI device objects [1].
Overall, it is better to bind drivers to platform devices than to their
ACPI companions, so convert the Toshiba Laptop ACPI Extras driver from
an ACPI driver to a platform one.
After this change, all of the subordinate hwmon, IIO, and LED class
devices will be registered under the platform device used for driver
binding instead of its ACPI companion.
While this is not expected to alter functionality, it changes sysfs
layout and so it will be visible to user space.
However, the sysfs attributes in toshiba_attr_group will still be there
in the sysfs directory of the ACPI companion of the platform device used
for driver binding to maintain backwards compatibility with possibly
existing user space utilities depending on the presence of those
attributes.
To facilitate subsequent conversion of the driver to a platform one,
make it install an ACPI notify handler directly instead of using
a .notify() callback in struct acpi_driver.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/5070377.GXAFRqVoOG@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: toshiba_acpi: Reorder code to avoid forward declaration
Move the definition of toshiba_acpi_notify() before the definitions of
the functions that will refer to it after subsequent updates to avoid
having to add a forward declarations of it.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/4734258.LvFx2qVVIh@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86/intel/tpmi: Use 32 bit aligned address for debugfs mem write
The memory write feature supports 32-bit writes to any TPMI offset.
However, future hardware generations may not allow writes to non-32-bit
aligned addresses due to hardware optimizations.
Since all TPMI addresses are 64-bit aligned and correspond to 64-bit
registers, enforce 32-bit alignment for write operations.
Werner Sembach [Tue, 24 Mar 2026 20:32:11 +0000 (21:32 +0100)]
platform/x86: uniwill-laptop: Apply features across all TUXEDO devices
Uses the more fine granular and/or new feature defines to enable more
features across the TUXEDO device lineup.
Also adds features to TUXEDO devices that where already present in the
driver, but not tested until now.
Reviewed-by: Armin Wolf <W_Armin@gmx.de> Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Link: https://patch.msgid.link/20260324203413.454361-5-wse@tuxedocomputers.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add alternative XMG Fusion system vendor name and clarify edition in ident.
Reviewed-by: Armin Wolf <W_Armin@gmx.de> Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Link: https://patch.msgid.link/20260324203413.454361-4-wse@tuxedocomputers.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Werner Sembach [Tue, 24 Mar 2026 20:32:09 +0000 (21:32 +0100)]
platform/x86: uniwill-laptop: Implement USB-C power priority setting
On some devices Uniwill offers the option to set the USB-C port to
prioritise charging or performance. This patch exposes this setting to the
userspace via sysfs for all TUXEDO devices supporting it.
Reviewed-by: Armin Wolf <W_Armin@gmx.de> Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Link: https://patch.msgid.link/20260324203413.454361-3-wse@tuxedocomputers.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Split hwmon feature define in smaller parts to accommodate for diverse
hardware. You can now specify the presence of a cpu and/or a gpu temp
sensor separately and if one or 2 fans exists.
Signed-off-by: Armin Wolf <W_Armin@gmx.de> Reviewed-by: Werner Sembach <wse@tuxedocomputers.com> Tested-by: Werner Sembach <wse@tuxedocomputers.com> Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Link: https://patch.msgid.link/20260324203413.454361-2-wse@tuxedocomputers.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Denis Benato [Mon, 2 Mar 2026 17:44:31 +0000 (18:44 +0100)]
platform/x86: asus-wmi: fix screenpad brightness range
Fix screenpad brightness range being too limited without reason:
testing this patch on a Zenbook Duo showed the hardware minimum not being
too low, therefore allow the user to configure the entire range, and
expose to userspace the hardware brightness range and value.
Fixes: 2c97d3e55b70 ("platform/x86: asus-wmi: add support for ASUS screenpad") Signed-off-by: Denis Benato <denis.benato@linux.dev> Signed-off-by: Luke Jones <luke@ljones.dev> Link: https://patch.msgid.link/20260302174431.349816-3-denis.benato@linux.dev Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Fix illogical screen off control by hardcoding 0 and 1 depending on the
requested brightness and also do not rely on the last screenpad power
state to issue screen brightness commands.
Denis Benato [Wed, 4 Mar 2026 13:26:08 +0000 (14:26 +0100)]
platform/x86: asus-wmi: do not enforce a battery charge threshold
Users are complaining for the battery limit being reset at 100% during
the boot process while the general consensus appears to not apply
unsolicited hardware changes, therefore stop resetting the battery
charge limit at boot and return -ENODATA on charge_end_threshold to
signal for an unknown limit.
Suggested-by: Antheas Kapenekakis <lkml@antheas.dev> Suggested-by: Derek J. Clark <derekjohn.clark@gmail.com> Signed-off-by: Denis Benato <denis.benato@linux.dev> Reviewed-by: Derek J. Clark <derekjohn.clark@gmail.com> Tested-by: Antheas Kapenekakis <lkml@antheas.dev> Link: https://patch.msgid.link/20260304132608.33815-1-denis.benato@linux.dev Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Mingyou Chen [Mon, 23 Mar 2026 13:22:18 +0000 (21:22 +0800)]
platform/x86: bitland-mifs-wmi: Add new Bitland MIFS WMI driver
Add a new driver for Bitland laptops that utilize the MIFS (MiInterface)
WMI interface.
The driver implements several features through the WMI interface:
- Platform Profile: Supports "Quiet", "Balanced", "Performance", and
"Full Speed" modes. The "Full Speed" mode is intelligently restricted
based on the AC adapter type (requires DC power, not supported on
USB-C charging) as required by the hardware.
- Hwmon: Provides monitoring for CPU, GPU, and System fan speeds,
as well as CPU temperature sensors.
- Keyboard Backlight: Integrated with the LED class device for
brightness control and provides sysfs attributes for keyboard modes
(cyclic, fixed, etc.).
- GPU Mode: Allows switching between Hybrid, Discrete, and UMA
graphics modes via sysfs.
- Hotkeys: Handles WMI events for system hotkeys (Calculator, Browser,
App launch) using sparse keymaps and reports status changes for
Airplane mode, Touchpad, and CapsLock.
- Fan Boost: Provides a sysfs interface to force fans to maximum speed.
Matthew Schwartz [Thu, 12 Mar 2026 21:22:46 +0000 (14:22 -0700)]
platform/x86: asus-nb-wmi: add DMI quirk for ASUS ROG Flow Z13-KJP GZ302EAC
The ASUS ROG Flow Z13-KJP GZ302EAC model uses sys_vendor name ASUS
rather than ASUSTeK COMPUTER INC., but it needs the same folio quirk as
the other ROG Flow Z13. To keep things simple, just match on sys_vendor
ASUS since it covers both.
Signed-off-by: Matthew Schwartz <matthew.schwartz@linux.dev> Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org> Reviewed-by: Denis Benato <denis.benato@linux.dev> Link: https://patch.msgid.link/20260312212246.1608080-1-matthew.schwartz@linux.dev Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Alok Tiwari [Tue, 10 Mar 2026 13:01:35 +0000 (06:01 -0700)]
platform/olpc: olpc-xo175-ec: Fix overflow error message to print inlen
The command length check validates inlen (> 5), but the error message
incorrectly printed resp_len. Print inlen so the log reflects the
actual command length.
Fixes: 0c3d931b3ab9e ("Platform: OLPC: Add XO-1.75 EC driver") Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com> Acked-by: Lubomir Rintel <lkundrak@v3.sk> Reviewed-by: Randy Dunlap <rdunlap@infradead.org> Link: https://patch.msgid.link/20260310130138.700687-1-alok.a.tiwari@oracle.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: lenovo: wmi-gamezone: Drop gz_chain_head
The gz_chain_head variable has been unused since the driver's initial
addition to the tree. Its use was eliminated between v3 and v4 during
development but due to the reference of gz_chain_head's wait_list
member, the compiler could not warn that it was unused.
After a (tip) commit ("locking/rwsem: Remove the list_head from struct
rw_semaphore"), which removed a reference to the variable passed to
__RWSEM_INITIALIZER(), certain configurations show an unused variable
warning from the Lenovo wmi-gamezone driver:
drivers/platform/x86/lenovo/wmi-gamezone.c:34:31: warning: 'gz_chain_head' defined but not used [-Wunused-variable]
34 | static BLOCKING_NOTIFIER_HEAD(gz_chain_head);
| ^~~~~~~~~~~~~
include/linux/notifier.h:119:39: note: in definition of macro 'BLOCKING_NOTIFIER_HEAD'
119 | struct blocking_notifier_head name = \
| ^~~~
Remove the variable to prevent the warning from showing up.
Fixes: 22024ac5366f ("platform/x86: Add Lenovo Gamezone WMI Driver") Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca> Link: https://patch.msgid.link/20260313-lenovo-wmi-gamezone-remove-gz_chain_head-v1-1-ce5231f0c6fa@kernel.org
[ij: reorganized the changelog] Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Li RongQing [Tue, 3 Mar 2026 07:46:35 +0000 (02:46 -0500)]
platform/x86: ISST: Check HWP support before MSR access
On some systems, HWP can be explicitly disabled in the BIOS settings
When HWP is disabled by firmware, the HWP CPUID bit is not set, and
attempting to read MSR_PM_ENABLE will result in a General Protection
(GP) fault.
Krishna Chomal [Mon, 2 Mar 2026 07:35:25 +0000 (13:05 +0530)]
platform/x86: hp-wmi: Add support for Omen 16-k0xxx (8A4D)
The HP Omen 16-k0xxx (board ID: 8A4D) has the same WMI interface as
other Victus S boards, but requires additional quirks for correctly
switching thermal profile.
Create a new quirk omen_v1_legacy_thermal_params which allows a board to
use Omen V1 thermal values, but rely on the older legacy
HP_OMEN_EC_THERMAL_PROFILE_OFFSET. Add the DMI board name to
victus_s_thermal_profile_boards[] table and map it to the newly added
quirk.
Testing on board 8A4D confirmed that platform profile is registered
successfully and fan RPMs are readable and controllable.
Krishna Chomal [Fri, 27 Feb 2026 15:41:06 +0000 (21:11 +0530)]
platform/x86: hp-wmi: Add support for Omen 16-wf1xxx (8C76)
The HP Omen 16-wf1xxx (board ID: 8C76) has the same WMI interface as
other Victus S boards, but requires quirks for correctly switching
thermal profile (similar to board 8C78).
Add the DMI board name to victus_s_thermal_profile_boards[] table and
map it to omen_v1_thermal_params.
Testing on board 8C76 confirmed that platform profile is registered
successfully and fan RPMs are readable and controllable.
Raed [Wed, 11 Mar 2026 13:13:38 +0000 (18:43 +0530)]
platform/x86: hp-wmi: Add Omen 16-xf0xxx (8BCA) support
The HP Omen 16-xf0xxx board 8BCA uses the same Victus-S fan and
thermal WMI path as other recently supported Omen/Victus boards,
but it requires Omen v1 thermal profile parameters for correct
platform profile behavior.
Add board 8BCA to victus_s_thermal_profile_boards[] and map it
to omen_v1_thermal_params.
Validated on HP Omen 16-xf0xxx (board 8BCA):
- /sys/firmware/acpi/platform_profile exposes
low-power/balanced/performance
- fan RPM reporting works (fan1_input/fan2_input)
- manual fan control works through hp-wmi hwmon (pwm1/pwm1_enable)
Dmitry Torokhov [Thu, 19 Mar 2026 02:56:17 +0000 (19:56 -0700)]
platform/x86: barco-p50-gpio: normalize return value of gpio_get
The GPIO get callback is expected to return 0 or 1 (or a negative error
code). Ensure that the value returned by p50_gpio_get() is normalized
to the [0, 1] range.
Fixes: 86ef402d805d606a ("gpiolib: sanitize the return value of gpio_chip::get()") Reviewed-by: Linus Walleij <linusw@kernel.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com> Link: https://patch.msgid.link/20260318-barco-p50-gpio-set-v2-1-c0a4a6416163@gmail.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Andy Shevchenko [Fri, 20 Mar 2026 22:11:43 +0000 (23:11 +0100)]
platform/surface: hotplug: Correct inclusion for GPIO APIs
The modern GPIO APIs are available for users via linux/gpio/consumer.h.
The linux/gpio.h is legacy header that is subject to remove. Hence
replace the latter by the former in the driver.
platform/x86: dell/dell-rbtn: Convert ACPI driver to a platform one
In all cases in which a struct acpi_driver is used for binding a driver
to an ACPI device object, a corresponding platform device is created by
the ACPI core and that device is regarded as a proper representation of
underlying hardware. Accordingly, a struct platform_driver should be
used by driver code to bind to that device. There are multiple reasons
why drivers should not bind directly to ACPI device objects [1].
Overall, it is better to bind drivers to platform devices than to their
ACPI companions, so convert the Dell Airplane Mode Switch (rbtn) ACPI
driver to a platform one.
After this change, the subordinate rfkill device will be registered
under the platform device used for driver binding instead of its ACPI
companion.
While this is not expected to alter functionality, it changes sysfs
layout and so it will be visible to user space.
To facilitate subsequent conversion of the driver to a platform one,
make it install an ACPI notify handler directly instead of using
a .notify() callback in struct acpi_driver.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/9591832.CDJkKcVGEf@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: system76: Convert ACPI driver to a platform one
In all cases in which a struct acpi_driver is used for binding a driver
to an ACPI device object, a corresponding platform device is created by
the ACPI core and that device is regarded as a proper representation of
underlying hardware. Accordingly, a struct platform_driver should be
used by driver code to bind to that device. There are multiple reasons
why drivers should not bind directly to ACPI device objects [1].
Overall, it is better to bind drivers to platform devices than to their
ACPI companions, so convert the System76 ACPI driver to a platform one.
After this change, the subordinate hwmon, input and LED class devices
will be registered under the platform device used for driver binding
instead of its ACPI companion.
While this is not expected to alter functionality, it changes sysfs
layout and so it will be visible to user space.
To facilitate subsequent conversion of the driver to a platform one,
make it install an ACPI notify handler directly instead of using
a .notify() callback in struct acpi_driver.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/13970743.uLZWGnKmhe@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: system76: Drop redundant devm_led_classdev_unregister()
Drop two redundant devm_led_classdev_unregister() calls from
system76_remove().
No intentional functional impact.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/5057164.GXAFRqVoOG@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: panasonic-laptop: Convert ACPI driver to a platform one
In all cases in which a struct acpi_driver is used for binding a driver
to an ACPI device object, a corresponding platform device is created by
the ACPI core and that device is regarded as a proper representation of
underlying hardware. Accordingly, a struct platform_driver should be
used by driver code to bind to that device. There are multiple reasons
why drivers should not bind directly to ACPI device objects [1].
Overall, it is better to bind drivers to platform devices than to their
ACPI companions, so convert the Panasonic laptop ACPI driver to a platform
one.
While this is not expected to alter functionality, it changes sysfs
layout and so it will be visible to user space.
To maintain backwards compatibility with possibly existing user space,
the sysfs attributes created by the driver under the ACPI device object
used by it are not relocated. Accordingly, the driver will continue to
use the driver_data pointer in struct acpi_device which needs to be
cleared on driver removal.
To facilitate subsequent conversion of the driver to a platform one,
make it install an ACPI notify handler directly instead of using
a .notify() callback in struct acpi_driver.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/13979037.uLZWGnKmhe@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: panasonic-laptop: Remove redundant checks from 3 functions
The device pointer cannot be NULL in acpi_pcc_hotkey_add() and
acpi_pcc_hotkey_remove() because these functions are ACPI driver
callbacks and NULL is never passed to any of them as an argument.
Likewise, acpi_pcc_hotkey_resume() is a resume callback of a
device driver and NULL is never passed to it as an argument, so
the dev pointer in it cannot be NULL.
Moreover, since acpi_pcc_hotkey_remove() and acpi_pcc_hotkey_resume()
can only run after acpi_pcc_hotkey_add() has completed successfully,
the acpi_driver_data() of the device object used by them cannot be
NULL when they run.
Drop all of the redundant NULL checks of the pointers mentioned above.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/1957824.tdWV9SEqCh@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: panasonic-laptop: Fix OPTD notifier registration and cleanup
An ACPI notify handler is leaked if device_create_file() returns an
error in acpi_pcc_hotkey_add().
Also, it is pointless to call pcc_unregister_optd_notifier() in
acpi_pcc_hotkey_remove() if pcc->platform is NULL and it is better
to arrange the cleanup code in that function in the same order as
the rollback code in acpi_pcc_hotkey_add().
Address the above by placing the pcc_register_optd_notifier() call in
acpi_pcc_hotkey_add() after the device_create_file() return value
check and placing the pcc_unregister_optd_notifier() call in
acpi_pcc_hotkey_remove() right before the device_remove_file() call.
Fixes: d5a81d8e864b ("platform/x86: panasonic-laptop: Add support for optical driver power in Y and W series") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/2411055.ElGaqSPkdT@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: panasonic-laptop: Make pcc_register_optd_notifier() void
Convert pcc_register_optd_notifier() whose return value is never used to
a void function.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/5093613.31r3eYUQgx@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: fujitsu: Convert laptop driver to a platform one
In all cases in which a struct acpi_driver is used for binding a driver
to an ACPI device object, a corresponding platform device is created by
the ACPI core and that device is regarded as a proper representation of
underlying hardware. Accordingly, a struct platform_driver should be
used by driver code to bind to that device. There are multiple reasons
why drivers should not bind directly to ACPI device objects [1].
Overall, it is better to bind drivers to platform devices than to their
ACPI companions, so convert the main part of the Fujitsu laptop driver
from an ACPI driver to a platform one.
After this change, the subordinate LED and input devices will be
registered under the platform device used for driver binding instead of
its ACPI companion.
While this is not expected to alter functionality, it changes sysfs
layout and so it will be visible to user space.
platform/x86: fujitsu: Convert backlight driver to a platform one
In all cases in which a struct acpi_driver is used for binding a driver
to an ACPI device object, a corresponding platform device is created by
the ACPI core and that device is regarded as a proper representation of
underlying hardware. Accordingly, a struct platform_driver should be
used by driver code to bind to that device. There are multiple reasons
why drivers should not bind directly to ACPI device objects [1].
Overall, it is better to bind drivers to platform devices than to their
ACPI companions, so convert the backlight part of the Fujitsu laptop
driver from an ACPI driver to a platform one.
After this change, the backlight and input subordinate devices will be
registered under the platform device used for driver binding instead of
its ACPI companion.
While this is not expected to alter functionality, it changes sysfs
layout and so it will be visible to user space.
To facilitate subsequent conversion of the driver to using struct
platform_driver instead of struct acpi_driver, make it install its ACPI
notify handlers directly instead of using struct acpi_driver .notify()
callbacks.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Jonathan Woithe <jwoithe@just42.net> Link: https://patch.msgid.link/3035290.e9J7NaK4W3@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: fujitsu: Reorder code to avoid forward declarations
Move the definitions of acpi_fujitsu_bl_notify() and
acpi_fujitsu_laptop_notify() along with some helpers above
the definitions of the functions that will refer to them
after subsequent changes, to avoid having to add forward
declarations of them.
No intentional functional impact.
Acked-by: Jonathan Woithe <jwoithe@just42.net> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/1950259.tdWV9SEqCh@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: fujitsu-tablet: Convert ACPI driver to a platform one
In all cases in which a struct acpi_driver is used for binding a driver
to an ACPI device object, a corresponding platform device is created by
the ACPI core and that device is regarded as a proper representation of
underlying hardware. Accordingly, a struct platform_driver should be
used by driver code to bind to that device. There are multiple reasons
why drivers should not bind directly to ACPI device objects [1].
Overall, it is better to bind drivers to platform devices than to their
ACPI companions, so convert the fujitsu-tablet ACPI driver to a platform
one.
After this change, the subordinate input device will be registered under
the platform device used for driver binding instead of its ACPI companion.
While this is not expected to alter functionality, it changes sysfs
layout and so it will be visible to user space.
platform/x86: wireless-hotkey: Convert ACPI driver to a platform one
In all cases in which a struct acpi_driver is used for binding a driver
to an ACPI device object, a corresponding platform device is created by
the ACPI core and that device is regarded as a proper representation of
underlying hardware. Accordingly, a struct platform_driver should be
used by driver code to bind to that device. There are multiple reasons
why drivers should not bind directly to ACPI device objects [1].
Overall, it is better to bind drivers to platform devices than to their
ACPI companions, so convert the airplane mode button for AMD, HP and
Xiaomi laptops driver from an ACPI driver to a platform one.
While this is not expected to alter functionality, it changes sysfs
layout and so it will be visible to user space.
To facilitate subsequent conversion of the driver to a platform one,
make it install an ACPI notify handler directly instead of using
a .notify() callback in struct acpi_driver.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/3953848.kQq0lBPeGt@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: topstar-laptop: Convert ACPI driver to a platform one
In all cases in which a struct acpi_driver is used for binding a driver
to an ACPI device object, a corresponding platform device is created by
the ACPI core and that device is regarded as a proper representation of
underlying hardware. Accordingly, a struct platform_driver should be
used by driver code to bind to that device. There are multiple reasons
why drivers should not bind directly to ACPI device objects [1].
Overall, it is better to bind drivers to platform devices than to their
ACPI companions, so convert the Topstar Laptop ACPI Extras driver from
an ACPI driver to a platform one.
While this is not expected to alter functionality, it changes sysfs
layout and so it will be visible to user space.
To facilitate subsequent conversion of the driver to a platform one,
make it install an ACPI notify handler directly instead of using
a .notify() callback in struct acpi_driver.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/3425557.44csPzL39Z@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: sony-laptop: Convert PIC driver to a platform one
In all cases in which a struct acpi_driver is used for binding a driver
to an ACPI device object, a corresponding platform device is created by
the ACPI core and that device is regarded as a proper representation of
underlying hardware. Accordingly, a struct platform_driver should be
used by driver code to bind to that device. There are multiple reasons
why drivers should not bind directly to ACPI device objects [1].
Overall, it is better to bind drivers to platform devices than to their
ACPI companions, so convert the Programmable IO Control (pic) part of
the Sony laptop driver from an ACPI driver to a platform one.
While this is not expected to alter functionality, it changes sysfs
layout and so it will be visible to user space.
platform/x86: sony-laptop: Convert NC driver to a platform one
In all cases in which a struct acpi_driver is used for binding a driver
to an ACPI device object, a corresponding platform device is created by
the ACPI core and that device is regarded as a proper representation of
underlying hardware. Accordingly, a struct platform_driver should be
used by driver code to bind to that device. There are multiple reasons
why drivers should not bind directly to ACPI device objects [1].
Overall, it is better to bind drivers to platform devices than to their
ACPI companions, so convert the Notebook Control (nc) part of the Sony
laptop driver from an ACPI driver to a platform one.
While this is not expected to alter functionality, it changes sysfs
layout and so it will be visible to user space.
To facilitate subsequent conversion of the driver to a platform one,
make it install an ACPI notify handler directly instead of using
a .notify() callback in struct acpi_driver.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/2559802.jE0xQCEvom@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
platform/x86: lg-laptop: Convert ACPI driver to a platform one
In all cases in which a struct acpi_driver is used for binding a driver
to an ACPI device object, a corresponding platform device is created by
the ACPI core and that device is regarded as a proper representation of
underlying hardware. Accordingly, a struct platform_driver should be
used by driver code to bind to that device. There are multiple reasons
why drivers should not bind directly to ACPI device objects [1].
Overall, it is better to bind drivers to platform devices than to their
ACPI companions, so convert the LG Gram ACPI features and hotkeys driver
from an ACPI driver to a platform one.
While this is not expected to alter functionality, it changes sysfs
layout and so it will be visible to user space.
platform/x86: lg-laptop: Drop debug-only ACPI notify handler
To facilitate subsequent conversion of the driver to using struct
platform_driver instead of struct acpi_driver, drop the debug-only
notify handler method from the driver.
No intentional functional impact beyond debug.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/3346280.5fSG56mABF@rafael.j.wysocki Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
David E. Box [Fri, 13 Mar 2026 01:51:45 +0000 (18:51 -0700)]
platform/x86/intel/vsec: Plumb ACPI PMT discovery tables through vsec
Some platforms expose PMT discovery via ACPI instead of PCI BARs. Add a
generic discovery source flag and carry ACPI discovery entries alongside
the existing PCI resource path so PMT clients can consume either.
Changes:
- Add enum intel_vsec_disc_source { _PCI, _ACPI }.
- Extend intel_vsec_platform_info and intel_vsec_device with source enum
and ACPI discovery table pointer/
- When src==ACPI, skip BAR resource setup and copy the ACPI discovery
entries into the aux device.
No user-visible behavior change yet; this only wires ACPI data through vsec
in preparation for ACPI-enumerated PMT clients.
projects / thirdparty / kernel / linux.git / log
