NFSv4.0 does not have TEST_STATEID/FREE_STATEID functionality, so
unlike NFSv4.1, the recovery procedure when stateids have expired or
have been revoked requires us to just forget the delegation.
On some Dell Latitude laptops ALPS device or Dell EC send one invalid byte
in 6 bytes ALPS packet. In this case psmouse driver enter out of sync
state. It looks like that all other bytes in packets are valid and also
device working properly. So there is no need to do full device reset, just
need to wait for byte which match condition for first byte (start of
packet). Because ALPS packets are bigger (6 or 8 bytes) default limit is
small.
This patch increase number of invalid bytes to size of 2 ALPS packets which
psmouse driver can drop before do full reset.
Resetting ALPS devices take some time and when doing reset on some Dell
laptops touchpad, trackstick and also keyboard do not respond. So it is
better to do it only if really necessary.
5th and 6th byte of ALPS trackstick V3 protocol match condition for first
byte of PS/2 3 bytes packet. When driver enters out of sync state and ALPS
trackstick is sending data then driver match 5th, 6th and next 1st bytes as
PS/2.
It basically means if user is using trackstick when driver is in out of
sync state driver will never resync. Processing these bytes as 3 bytes PS/2
data cause total mess (random cursor movements, random clicks) and make
trackstick unusable until psmouse driver decide to do full device reset.
Lot of users reported problems with ALPS devices on Dell Latitude E6440,
E6540 and E7440 laptops. ALPS device or Dell EC for unknown reason send
some invalid ALPS PS/2 bytes which cause driver out of sync. It looks like
that i8042 and psmouse/alps driver always receive group of 6 bytes packets
so there are no missing bytes and no bytes were inserted between valid
ones.
This patch does not fix root of problem with ALPS devices found in Dell
Latitude laptops but it does not allow to process some (invalid)
subsequence of 6 bytes ALPS packets as 3 bytes PS/2 when driver is out of
sync.
So with this patch trackstick input device does not report bogus data when
also driver is out of sync, so trackstick should be usable on those
machines.
The dm-raid superblock (struct dm_raid_superblock) is padded to 512
bytes and that size is being used to read it in from the metadata
device into one preallocated page.
Reading or writing this on a 512-byte sector device works fine but on
a 4096-byte sector device this fails.
Set the dm-raid superblock's size to the logical block size of the
metadata device, because IO at that size is guaranteed too work. Also
add a size check to avoid silent partial metadata loss in case the
superblock should ever grow past the logical block size or PAGE_SIZE.
[includes pointer math fix from Dan Carpenter] Reported-by: "Liuhua Wang" <lwang@suse.com> Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The walk code was using a 'ro_spine' to hold it's locked btree nodes.
But this data structure is designed for the rolling lock scheme, and
as such automatically unlocks blocks that are two steps up the call
chain. This is not suitable for the simple recursive walk algorithm,
which retraces its steps.
This code is only used by the persistent array code, which in turn is
only used by dm-cache. In order to trigger it you need to have a
mapping tree that is more than 2 levels deep; which equates to 8-16
million cache blocks. For instance a 4T ssd with a very small block
size of 32k only just triggers this bug.
The fix just places the locked blocks on the stack, and stops using
the ro_spine altogether.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Priority of a merged request is computed by ioprio_best(). If one of the
requests has undefined priority (IOPRIO_CLASS_NONE) and another request
has priority from IOPRIO_CLASS_BE, the function will return the
undefined priority which is wrong. Fix the function to properly return
priority of a request with the defined priority.
Fixes: d58cdfb89ce0c6bd5f81ae931a984ef298dbda20 Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch over the msgctl, shmat, shmctl and semtimedop syscalls to use the compat
layer. The problem was found with the debian procenv package, which called
shmctl(0, SHM_INFO, &info);
in which the shmctl syscall then overwrote parts of the surrounding areas on
the stack on which the info variable was stored and thus lead to a segfault
later on.
Additionally fix the definition of struct shminfo64 to use unsigned longs like
the other architectures. This has no impact on userspace since we only have a
32bit userspace up to now.
Signed-off-by: Helge Deller <deller@gmx.de> Cc: John David Anglin <dave.anglin@bell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setups that use the blk-mq I/O path can lock up if a host with a single
device that has its door locked enters EH. Make sure to only send the
command to re-lock the door to devices that actually were reset and thus
might have lost their state. Otherwise the EH code might be get blocked
on blk_get_request as all requests for non-reset devices might be in use.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Meelis Roos <meelis.roos@ut.ee> Tested-by: Meelis Roos <meelis.roos@ut.ee> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For pNFS direct writes, layout driver may dynamically allocate ds_cinfo.buckets.
So we need to take care to free them when freeing dreq.
Ideally this needs to be done inside layout driver where ds_cinfo.buckets
are allocated. But buckets are attached to dreq and reused across LD IO iterations.
So I feel it's OK to free them in the generic layer.
Found by the UC-KLEE tool: A user could supply less input to
firewire-cdev ioctls than write- or write/read-type ioctl handlers
expect. The handlers used data from uninitialized kernel stack then.
This could partially leak back to the user if the kernel subsequently
generated fw_cdev_event_'s (to be read from the firewire-cdev fd)
which notably would contain the _u64 closure field which many of the
ioctl argument structures contain.
The fact that the handlers would act on random garbage input is a
lesser issue since all handlers must check their input anyway.
The fix simply always null-initializes the entire ioctl argument buffer
regardless of the actual length of expected user input. That is, a
runtime overhead of memset(..., 40) is added to each firewirew-cdev
ioctl() call. [Comment from Clemens Ladisch: This part of the stack is
most likely to be already in the cache.]
Remarks:
- There was never any leak from kernel stack to the ioctl output
buffer itself. IOW, it was not possible to read kernel stack by a
read-type or write/read-type ioctl alone; the leak could at most
happen in combination with read()ing subsequent event data.
- The actual expected minimum user input of each ioctl from
include/uapi/linux/firewire-cdev.h is, in bytes:
[0x00] = 32, [0x05] = 4, [0x0a] = 16, [0x0f] = 20, [0x14] = 16,
[0x01] = 36, [0x06] = 20, [0x0b] = 4, [0x10] = 20, [0x15] = 20,
[0x02] = 20, [0x07] = 4, [0x0c] = 0, [0x11] = 0, [0x16] = 8,
[0x03] = 4, [0x08] = 24, [0x0d] = 20, [0x12] = 36, [0x17] = 12,
[0x04] = 20, [0x09] = 24, [0x0e] = 4, [0x13] = 40, [0x18] = 4.
Reported-by: David Ramos <daramos@stanford.edu> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ARM64 currently doesn't fix up faults on the single-byte (strb) case of
__clear_user... which means that we can cause a nasty kernel panic as an
ordinary user with any multiple PAGE_SIZE+1 read from /dev/zero.
i.e.: dd if=/dev/zero of=foo ibs=1 count=1 (or ibs=65537, etc.)
This is a pretty obscure bug in the general case since we'll only
__do_kernel_fault (since there's no extable entry for pc) if the
mmap_sem is contended. However, with CONFIG_DEBUG_VM enabled, we'll
always fault.
if (!down_read_trylock(&mm->mmap_sem)) {
if (!user_mode(regs) && !search_exception_tables(regs->pc))
goto no_context;
retry:
down_read(&mm->mmap_sem);
} else {
/*
* The above down_read_trylock() might have succeeded in
* which
* case, we'll have missed the might_sleep() from
* down_read().
*/
might_sleep();
if (!user_mode(regs) && !search_exception_tables(regs->pc))
goto no_context;
}
Fix that by adding an extable entry for the strb instruction, since it
touches user memory, similar to the other stores in __clear_user.
The kuser helpers page is not set up on non-MMU systems, so it does
not make sense to allow CONFIG_KUSER_HELPERS to be enabled when
CONFIG_MMU=n. Allowing it to be set on !MMU results in an oops in
set_tls (used in execve and the arm_syscall trap handler):
As best I can tell this issue existed for the set_tls ARM syscall
before commit fbfb872f5f41 "ARM: 8148/1: flush TLS and thumbee
register state during exec" consolidated the TLS manipulation code
into the set_tls helper function, but now that we're using it to flush
register state during execve, !MMU users encounter the oops at the
first exec.
Prevent CONFIG_MMU=n configurations from enabling
CONFIG_KUSER_HELPERS.
Fixes: fbfb872f5f41 (ARM: 8148/1: flush TLS and thumbee register state during exec) Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com> Reported-by: Stefan Agner <stefan@agner.ch> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon receiving the last fragment, all but the first fragment
are freed, but the multicast check for statistics at the end
of the function refers to the current skb (the last fragment)
causing a use-after-free bug.
Since multicast frames cannot be fragmented and we check for
this early in the function, just modify that check to also
do the accounting to fix the issue.
When VLAN is in use in macvtap_put_user, we end up setting
csum_start to the wrong place. The result is that the whoever
ends up doing the checksum setting will corrupt the packet instead
of writing the checksum to the expected location, usually this
means writing the checksum with an offset of -4.
This patch fixes this by adjusting csum_start when VLAN tags are
detected.
Fixes: f09e2249c4f5 ("macvtap: restore vlan header on user read") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
The LTR is the handshake between the device and the root
complex about the latency allowed when the bus exits power
save. This configuration was missing and this led to high
latency in the link power up. The end user could experience
high latency in the network because of this.
Large (greater than 32k, the value of PAGE_ALLOC_COSTLY_ORDER) auth
tickets will have their buffers vmalloc'ed, which leads to the
following crash in crypto:
Userspace actually passes single parameter (path name) to the umount
syscall, so new umount just fails. Fix it by requesting old umount
syscall implementation and re-wiring umount to it.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Samsung pci-e SSDs on macbooks failed miserably on NCQ commands, so 67809f85d31e ("ahci: disable NCQ on Samsung pci-e SSDs on macbooks")
disabled NCQ on them. It turns out that NCQ is fine as long as MSI is
not used, so let's turn off MSI and leave NCQ on.
Signed-off-by: Tejun Heo <tj@kernel.org> Link: https://bugzilla.kernel.org/show_bug.cgi?id=60731 Tested-by: <dorin@i51.org> Tested-by: Imre Kaloz <kaloz@openwrt.org> Fixes: 67809f85d31e ("ahci: disable NCQ on Samsung pci-e SSDs on macbooks") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Audit rules disappear when an inode they watch is evicted from the cache.
This is likely not what we want.
The guilty commit is "fsnotify: allow marks to not pin inodes in core",
which didn't take into account that audit_tree adds watches with a zero
mask.
Adding any mask should fix this.
Fixes: 90b1e7a57880 ("fsnotify: allow marks to not pin inodes in core") Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Atomicity between xchg and cmpxchg cannot be guaranteed when xchg is
implemented with a swap and cmpxchg is implemented with locks.
Without this, e.g. mcs_spin_lock and mcs_spin_unlock are broken.
Signed-off-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise rcu_irq_{enter,exit}() do not happen and we get dumps like:
====================
[ 188.275021] ===============================
[ 188.309351] [ INFO: suspicious RCU usage. ]
[ 188.343737] 3.18.0-rc3-00068-g20f3963-dirty #54 Not tainted
[ 188.394786] -------------------------------
[ 188.429170] include/linux/rcupdate.h:883 rcu_read_lock() used
illegally while idle!
[ 188.505235]
other info that might help us debug this:
Based almost entirely upon a patch by Paul E. McKenney.
Reported-by: Meelis Roos <mroos@linux.ee> Tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code is trying to go through the standard PCI config space
interfaces to read the PCI controller's PCI_STATUS register.
This doesn't work, because we more often than not do not enumerate
the PCI controller as a bonafide PCI device during the OF device
node scan. Therefore bus->self remains NULL.
Existing common code for PSYCHO and PSYCHO-like PCI controllers
handles this properly, by doing the config space access directly.
Do the same here, pbm->pci_ops->{read,write}().
Reported-by: Meelis Roos <mroos@linux.ee> Tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VD_OP_GET_VTOC operation will succeed only if the vdisk backend has a
VTOC label, otherwise it will fail. In particular, it will return error
48 (ENOTSUP) if the disk has an EFI label. VTOC disk labels are already
handled by directly reading the disk in block/partitions/sun.c (enabled by
CONFIG_SUN_PARTITION which defaults to y on SPARC). Since port->label is
unused in the driver, remove the call and the field.
Signed-off-by: Dwight Engen <dwight.engen@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vio_dring_avail() will allow use of every dring entry, but when the last
entry is allocated then dr->prod == dr->cons which is indistinguishable from
the ring empty condition. This causes the next allocation to reuse an entry.
When this happens in sunvdc, the server side vds driver begins nack'ing the
messages and ends up resetting the ldc channel. This problem does not effect
sunvnet since it checks for < 2.
The fix here is to just never allocate the very last dring slot so that full
and empty are not the same condition. The request start path was changed to
check for the ring being full a bit earlier, and to stop the blk_queue if
there is no space left. The blk_queue will be restarted once the ring is
only half full again. The number of ring entries was increased to 512 which
matches the sunvnet and Solaris vdc drivers, and greatly reduces the
frequency of hitting the ring full condition and the associated blk_queue
stop/starting. The checks in sunvent were adjusted to account for
vio_dring_avail() returning 1 less.
Signed-off-by: Dwight Engen <dwight.engen@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ldc_map_sg() could fail its check that the number of pages referred to
by the sg scatterlist was <= the number of cookies.
This fixes the issue by doing a similar thing to the xen-blkfront driver,
ensuring that the scatterlist will only ever contain a segment count <=
port->ring_cookies, and each segment will be page aligned, and <= page
size. This ensures that the scatterlist is always mappable.
Signed-off-by: Dwight Engen <dwight.engen@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LDom diskserver doesn't return reliable geometry data. In addition,
the types for all fields in the vio_disk_geom are u16, which were being
truncated in the cast into the u8's of the Linux struct hd_geometry.
Modify vdc_getgeo() to compute the geometry from the disk's capacity in a
manner consistent with xen-blkfront::blkif_getgeo().
Signed-off-by: Dwight Engen <dwight.engen@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interpret the media type from v1.1 protocol to support CDROM/DVD.
For v1.0 protocol, a disk's size continues to be calculated from the
geometry returned by the vdisk server. The geometry returned by the server
can be less than the actual number of sectors available in the backing
image/device due to the rounding in the division used to compute the
geometry in the vdisk server.
In v1.1 protocol a disk's actual size in sectors is returned during the
handshake. Use this size when v1.1 protocol is negotiated. Since this size
will always be larger than the former geometry computed size, disks created
under v1.0 will be forwards compatible to v1.1, but not vice versa.
Signed-off-by: Dwight Engen <dwight.engen@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A very minimal and simple user space application allocating an SCTP
socket, setting SCTP_AUTH_KEY setsockopt(2) on it and then closing
the socket again will leak the memory containing the authentication
key from user space:
This is bad because of two things, we can bring down a machine from
user space when auth_enable=1, but also we would leave security sensitive
keying material in memory without clearing it after use. The issue is
that sctp_auth_create_key() already sets the refcount to 1, but after
allocation sctp_auth_set_key() does an additional refcount on it, and
thus leaving it around when we free the socket.
Fixes: 65b07e5d0d0 ("[SCTP]: API updates to suport SCTP-AUTH extensions.") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Vlad Yasevich <vyasevich@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the INIT chunk parameter verification dissects through many things
in order to detect malformed input, it misses to actually check parameters
inside of parameters. E.g. RFC5061, section 4.2.4 proposes a 'set primary
IP address' parameter in ASCONF, which has as a subparameter an address
parameter.
So an attacker may send a parameter type other than SCTP_PARAM_IPV4_ADDRESS
or SCTP_PARAM_IPV6_ADDRESS, param_type2af() will subsequently return 0
and thus sctp_get_af_specific() returns NULL, too, which we then happily
dereference unconditionally through af->from_addr_param().
A minimal way to address this is to check for NULL as we do on all
other such occasions where we know sctp_get_af_specific() could
possibly return with NULL.
Fixes: d6de3097592b ("[SCTP]: Add the handling of "Set Primary IP Address" parameter to INIT") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Vlad Yasevich <vyasevich@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise it gets overwritten by register_netdev().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ip6_tnl_dev_init() sets the dev->iflink via a call to
ip6_tnl_link_config(). After that, register_netdevice()
sets dev->iflink = -1. So we loose the iflink configuration
for ipv6 tunnels. Fix this by using ip6_tnl_dev_init() as the
ndo_init function. Then ip6_tnl_dev_init() is called after
dev->iflink is set to -1 from register_netdevice().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f363e45fd118 ("net/ceph: make ceph_msgr_wq non-reentrant")
effectively removed WQ_MEM_RECLAIM flag from ceph_msgr_wq. This is
wrong - libceph is very much a memory reclaim path, so restore it.
If we hit any errors in btrfs_lookup_csums_range, we'll loop through all
the csums we allocate and free them. But the code was using list_entry
incorrectly, and ended up trying to free the on-stack list_head instead.
The string property read helpers will run off the end of the buffer if
it is handed a malformed string property. Rework the parsers to make
sure that doesn't happen. At the same time add new test cases to make
sure the functions behave themselves.
The original implementations of of_property_read_string_index() and
of_property_count_strings() both open-coded the same block of parsing
code, each with it's own subtly different bugs. The fix here merges
functions into a single helper and makes the original functions static
inline wrappers around the helper.
One non-bugfix aspect of this patch is the addition of a new wrapper,
of_property_read_string_array(). The new wrapper is needed by the
device_properties feature that Rafael is working on and planning to
merge for v3.19. The implementation is identical both with and without
the new static inline wrapper, so it just got left in to reduce the
churn on the header file.
Signed-off-by: Grant Likely <grant.likely@linaro.org> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Darren Hart <darren.hart@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race condition when removing glue directory.
It can be reproduced in following test:
path 1: Add first child device
device_add()
get_device_parent()
/*find parent from glue_dirs.list*/
list_for_each_entry(k, &dev->class->p->glue_dirs.list, entry)
if (k->parent == parent_kobj) {
kobj = kobject_get(k);
break;
}
....
class_dir_create_and_add()
path2: Remove last child device under glue dir
device_del()
cleanup_device_parent()
cleanup_glue_dir()
kobject_put(glue_dir);
If path2 has been called cleanup_glue_dir(), but not
call kobject_put(glue_dir), the glue dir is still
in parent's kset list. Meanwhile, path1 find the glue
dir from the glue_dirs.list. Path2 may release glue dir
before path1 call kobject_get(). So kernel will report
the warning and bug_on.
This is a "classic" problem we have of a kref in a list
that can be found while the last instance could be removed
at the same time.
This patch reuse gdp_mutex to fix this race condition.
The following calltrace is captured in kernel 3.4, but
the latest kernel still has this bug.
The acpi-video backlight interface on the Acer KAV80 is broken, and worse
it causes the entire machine to slow down significantly after a suspend/resume.
Blacklist it, and use the acer-wmi backlight interface instead. Note that
the KAV80 is somewhat unique in that it is the only Acer model where we
fall back to acer-wmi after blacklisting, rather then using the native
(e.g. intel) backlight driver. This is done because there is no native
backlight interface on this model.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1128309 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we fail to allocate page vector in rbd_obj_read_sync() we just
basically ignore the problem and continue which will result in an oops
later. Fix the problem by returning proper error.
CC: Yehuda Sadeh <yehuda@inktank.com> CC: Sage Weil <sage@inktank.com> CC: ceph-devel@vger.kernel.org
Coverity-id: 1226882 Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Ilya Dryomov <idryomov@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, there's no guarantee that udc->driver
will be valid when using soft_connect sysfs
interface. In fact, we can very easily trigger
a NULL pointer dereference by trying to disconnect
when a gadget driver isn't loaded.
During Halt Endpoint Test, our interrupt endpoint
will be disabled, which will clear out ep->desc
to NULL. Unless we call config_ep_by_speed() again,
we will not be able to enable this endpoint which
will make us fail that test.
Fixes: f9c56cd (usb: gadget: Clear usb_endpoint_descriptor
inside the struct usb_ep on disable) Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to our Gadget Framework API documentation,
->set_halt() *must* return -EAGAIN if we have pending
transfers (on either direction) or FIFO isn't empty (on
TX endpoints).
Fix this bug so that the mass storage gadget can be used
without stall=0 parameter.
This patch should be backported to all kernels since v3.2.
Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On archs with PAGE_SIZE >= 64 KiB the function skcipher_alloc_sgl()
fails with -ENOMEM no matter what user space actually requested.
This is caused by the fact sock_kmalloc call inside the function tried
to allocate more memory than allowed by the default kernel socket buffer
size (kernel param net.core.optmem_max).
Signed-off-by: Ondrej Kozina <okozina@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WARN_ON checking whether i_mutex is held in
pagecache_isize_extended() was wrong because some filesystems (e.g.
XFS) use different locks for serialization of truncates / writes. So
just remove the check.
Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the TSC is unusable or disabled, then this patch fixes:
- Confusion while trying to clear old APIC interrupts.
- Division by zero and incorrect programming of the TSC deadline
timer.
This fixes boot if the CPU has a TSC deadline timer but a missing or
broken TSC. The failure to boot can be observed with qemu using
-cpu qemu64,-tsc,+tsc-deadline
This also happens to me in nested KVM for unknown reasons.
With this patch, I can boot cleanly (although without a TSC).
If userland creates a timer without specifying a sigevent info, we'll
create one ourself, using a stack local variable. Particularly will we
use the timer ID as sival_int. But as sigev_value is a union containing
a pointer and an int, that assignment will only partially initialize
sigev_value on systems where the size of a pointer is bigger than the
size of an int. On such systems we'll copy the uninitialized stack bytes
from the timer_create() call to userland when the timer actually fires
and we're going to deliver the signal.
Initialize sigev_value with 0 to plug the stack info leak.
It affects non-(V)HT rates and can lead to selecting an rts_cts rate
that is not a basic rate or way superior to the reference rate (ATM
rates[0] used for the 1st attempt of the protected frame data).
E.g, assuming drivers register growing (bitrate) sorted tables of
ieee80211_rate-s, having :
- rates[0].idx == d'2 and basic_rates == b'10100
will select rts_cts idx b'10011 & ~d'(BIT(2)-1), i.e. 1, likewise
- rates[0].idx == d'2 and basic_rates == b'10001
will select rts_cts idx b'10000
The first is not a basic rate and the second is > rates[0].
Also, wrt severity of the addressed misbehavior, ATM we only have one
rts_cts_rate_idx rather than one per rate table entry, so this idx might
still point to bitrates > rates[1..MAX_RATES].
Fixes: 5253ffb8c9e1 ("mac80211: always pick a basic rate to tx RTS/CTS for pre-HT rates") Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device's dev_pm_ops::freeze callback fails during the QUIESCE
phase, we don't rollback things correctly calling the thaw and complete
callbacks. This could leave some devices in a suspended state in case of
an error during resuming from hibernation.
Signed-off-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel oops can cause the tty to be unreleaseable (for example, if
n_tty_read() crashes while on the read_wait queue). This will cause
tty_release() to endlessly loop without sleeping.
Use a killable sleep timeout which grows by 2n+1 jiffies over the interval
[0, 120 secs.) and then jumps to forever (but still killable).
NB: killable just allows for the task to be rewoken manually, not
to be terminated.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to a switched left and right side of an assignment,
dquot_writeback_dquots() never returned error. This could result in
errors during quota writeback to not be reported to userspace properly.
Fix it.
Coverity-id: 1226884 Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check whether quota format is set even though there are no
quota files with journalled quota is pointless and it actually
makes it impossible to turn off journalled quotas (as there's
no way to unset journalled quota format). Just remove the check.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unknown operation numbers are caught in nfsd4_decode_compound() which
sets op->opnum to OP_ILLEGAL and op->status to nfserr_op_illegal. The
error causes the main loop in nfsd4_proc_compound() to skip most
processing. But nfsd4_proc_compound also peeks ahead at the next
operation in one case and doesn't take similar precautions there.
Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When sg_scsi_ioctl() fails to prepare request to submit in
blk_rq_map_kern() we jump to a label where we just end up copying
(luckily zeroed-out) kernel buffer to userspace instead of reporting
error. Fix the problem by jumping to the right label.
CC: Jens Axboe <axboe@kernel.dk> CC: linux-scsi@vger.kernel.org
Coverity-id: 1226871 Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed up the, now unused, out label.
If __bitmap_shift_left() or __bitmap_shift_right() are asked to shift by
a multiple of BITS_PER_LONG, they will try to shift a long value by
BITS_PER_LONG bits which is undefined. Change the functions to avoid
the undefined shift.
Coverity id: 1192175
Coverity id: 1192174 Signed-off-by: Jan Kara <jack@suse.cz> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ff7ee93f4715 ("cgroup/kmemleak: Annotate alloc_page() for cgroup
allocations") introduces kmemleak_alloc() for alloc_page_cgroup(), but
corresponding kmemleak_free() is missing, which makes kmemleak be
wrongly disabled after memory offlining. Log is pasted at the end of
this commit message.
This patch add kmemleak_free() into free_page_cgroup(). During page
offlining, this patch removes corresponding entries in kmemleak rbtree.
After that, the freed memory can be allocated again by other subsystems
without killing kmemleak.
bash # for x in 1 2 3 4; do echo offline > /sys/devices/system/memory/memory$x/state ; sleep 1; done ; dmesg | grep leak
[10238.622067] scsi host3: uas_eh_bus_reset_handler start
[10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10245.779365] usb 3-4: device descriptor read/8, error -110
[10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10250.897603] usb 3-4: device descriptor read/8, error -110
[10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
[10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140
<snip>
[10251.059473] Call Trace:
[10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130
[10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0
[10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0
[10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100
[10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70
[10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0
[10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas]
[10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas]
[10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0
[10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas]
[10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110
[10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270
<snip>
The problem is the following call sequence (simplified):
1) usb_reset_device
2) usb_reset_and_verify_device
2) hub_port_init
3) hub_port_finish_reset
3) xhci_discover_or_reset_device
This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0
4) usb_get_device_descriptor
This fails
5) hub_port_init fails
6) usb_reset_and_verify_device fails, does not restore device config
7) uas_post_reset
8) xhci_alloc_streams
NULL deref on the free-ed ring
This commit fixes this by not allowing usb_alloc_streams to continue if
the device is not configured.
Note that we do allow usb_free_streams to continue after a (logical)
disconnect, as it is necessary to explicitly free the streams at the xhci
controller level.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes mass-storage devices using the Bulk-only transport will
mistakenly skip the data phase of a command. Rather than sending the
data expected by the host or sending a zero-length packet, they go
directly to the status phase and send the CSW.
This causes problems for usb-storage, for obvious reasons. The driver
will interpret the CSW as a short data transfer and will wait to
receive a CSW. The device won't have anything left to send, so the
command eventually times out.
The SCSI layer doesn't retry commands after they time out (this is a
relatively recent change). Therefore we should do our best to detect
a skipped data phase and handle it promptly.
This patch adds code to do that. If usb-storage receives a short
13-byte data transfer from the device, and if the first four bytes of
the data match the CSW signature, the driver will set the residue to
the full transfer length and interpret the data as a CSW.
This fixes Bugzilla #86611.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Tested-by: Paul Osmialowski <newchief@king.net.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If PM_RUNTIME is enabled, it is easy to trigger the following backtrace
on pxa2xx hosts:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at /home/lumag/linux/arch/arm/mach-pxa/clock.c:35 clk_disable+0xa0/0xa8()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-00007-g1b3d2ee-dirty #104
[<c000de68>] (unwind_backtrace) from [<c000c078>] (show_stack+0x10/0x14)
[<c000c078>] (show_stack) from [<c001d75c>] (warn_slowpath_common+0x6c/0x8c)
[<c001d75c>] (warn_slowpath_common) from [<c001d818>] (warn_slowpath_null+0x1c/0x24)
[<c001d818>] (warn_slowpath_null) from [<c0015e80>] (clk_disable+0xa0/0xa8)
[<c0015e80>] (clk_disable) from [<c02507f8>] (pxa2xx_spi_suspend+0x2c/0x34)
[<c02507f8>] (pxa2xx_spi_suspend) from [<c0200360>] (platform_pm_suspend+0x2c/0x54)
[<c0200360>] (platform_pm_suspend) from [<c0207fec>] (dpm_run_callback.isra.14+0x2c/0x74)
[<c0207fec>] (dpm_run_callback.isra.14) from [<c0209254>] (__device_suspend+0x120/0x2f8)
[<c0209254>] (__device_suspend) from [<c0209a94>] (dpm_suspend+0x50/0x208)
[<c0209a94>] (dpm_suspend) from [<c00455ac>] (suspend_devices_and_enter+0x8c/0x3a0)
[<c00455ac>] (suspend_devices_and_enter) from [<c0045ad4>] (pm_suspend+0x214/0x2a8)
[<c0045ad4>] (pm_suspend) from [<c04b5c34>] (test_suspend+0x14c/0x1dc)
[<c04b5c34>] (test_suspend) from [<c000880c>] (do_one_initcall+0x8c/0x1fc)
[<c000880c>] (do_one_initcall) from [<c04aecfc>] (kernel_init_freeable+0xf4/0x1b4)
[<c04aecfc>] (kernel_init_freeable) from [<c0378078>] (kernel_init+0x8/0xec)
[<c0378078>] (kernel_init) from [<c0009590>] (ret_from_fork+0x14/0x24)
---[ end trace 46524156d8faa4f6 ]---
This happens because suspend function tries to disable a clock that is
already disabled by runtime_suspend callback. Add if
(!pm_runtime_suspended()) checks to suspend/resume path.
Fixes: 7d94a505858 (spi/pxa2xx: add support for runtime PM) Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Reported-by: Andrea Adami <andrea.adami@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When mapped RX DMA entries are unmapped in an error condition when DMA
is firstly configured in the driver, the number of TX DMA entries was
passed in, which is incorrect
Signed-off-by: Ray Jui <rjui@broadcom.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On ISOC endpoints the last trb_pool entry used as a
LINK TRB is not getting zeroed out correctly due to
memset being called incorrectly and in the wrong place.
If pool allocated from DMA was not zero-initialized
to begin with this will result in the size and ctrl
values being random garbage. Call memset correctly after
assignment of the trb_link pointer.
Fixes: f6bafc6a1c ("usb: dwc3: convert TRBs into bitshifts") Signed-off-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An official recent Windows driver from FTDI detects counterfeit devices
and reprograms the internal EEPROM containing the USB PID to 0, effectively
bricking the device.
Add support for this VID/PID pair to correctly bind the driver on these
devices.
Enable Silicon Labs Ember VID chips to enumerate with the cp210x usb serial
driver. EM358x devices operating with the Ember Z-Net 5.1.2 stack may now
connect to host PCs over a USB serial link.
uart_get_baud_rate() will return baud == 0 if the max rate is set
to the "magic" 38400 rate and the SPD_* flags are also specified.
On the first iteration, if the current baud rate is higher than the
max, the baud rate is clamped at the max (which in the degenerate
case is 38400). On the second iteration, the now-"magic" 38400 baud
rate selects the possibly higher alternate baud rate indicated by
the SPD_* flag. Since only two loop iterations are performed, the
loop is exited, a kernel WARNING is generated and a baud rate of
0 is returned.
Only perform the "magic" 38400 -> SPD_* baud transform on the first
loop iteration, which prevents the degenerate case from recognizing
the clamped baud rate as the "magic" 38400 value.
Reported-by: Robert Święcki <robert@swiecki.net> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In older versions of the IIO framework it was possible to pass a completely
different set of channels to iio_buffer_register() as the one that is
assigned to the IIO device. Commit 959d2952d124 ("staging:iio: make
iio_sw_buffer_preenable much more general.") introduced a restriction that
requires that the set of channels that is passed to iio_buffer_register() is
a subset of the channels assigned to the IIO device as the IIO core will use
the list of channels that is assigned to the device to lookup a channel by
scan index in iio_compute_scan_bytes(). If it can not find the channel the
function will crash. This patch fixes the issue by making sure that the same
set of channels is assigned to the IIO device and passed to
iio_buffer_register().
Note that we need to remove the IIO_CHAN_INFO_RAW and IIO_CHAN_INFO_SCALE
info attributes from the channels since we don't actually want those to be
registered.
Fixes: 959d2952d124 ("staging:iio: make iio_sw_buffer_preenable much more general.") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In older versions of the IIO framework it was possible to pass a
completely different set of channels to iio_buffer_register() as the one
that is assigned to the IIO device. Commit 959d2952d124 ("staging:iio: make
iio_sw_buffer_preenable much more general.") introduced a restriction that
requires that the set of channels that is passed to iio_buffer_register() is
a subset of the channels assigned to the IIO device as the IIO core will use
the list of channels that is assigned to the device to lookup a channel by
scan index in iio_compute_scan_bytes(). If it can not find the channel the
function will crash. This patch fixes the issue by making sure that the same
set of channels is assigned to the IIO device and passed to
iio_buffer_register().
Fixes: 959d2952d124 ("staging:iio: make iio_sw_buffer_preenable much more general.") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PM freezer relies on having all tasks frozen by the time devices are
getting frozen so that no task will touch them while they are getting
frozen. But OOM killer is allowed to kill an already frozen task in
order to handle OOM situtation. In order to protect from late wake ups
OOM killer is disabled after all tasks are frozen. This, however, still
keeps a window open when a killed task didn't manage to die by the time
freeze_processes finishes.
Reduce the race window by checking all tasks after OOM killer has been
disabled. This is still not race free completely unfortunately because
oom_killer_disable cannot stop an already ongoing OOM killer so a task
might still wake up from the fridge and get killed without
freeze_processes noticing. Full synchronization of OOM and freezer is,
however, too heavy weight for this highly unlikely case.
Introduce and check oom_kills counter which gets incremented early when
the allocator enters __alloc_pages_may_oom path and only check all the
tasks if the counter changes during the freezing attempt. The counter
is updated so early to reduce the race window since allocator checked
oom_killer_disabled which is set by PM-freezing code. A false positive
will push the PM-freezer into a slow path but that is not a big deal.
Changes since v1
- push the re-check loop out of freeze_processes into
check_frozen_processes and invert the condition to make the code more
readable as per Rafael
Fixes: f660daac474c6f (oom: thaw threads if oom killed thread is frozen before deferring) Signed-off-by: Michal Hocko <mhocko@suse.cz> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since f660daac474c6f (oom: thaw threads if oom killed thread is frozen
before deferring) OOM killer relies on being able to thaw a frozen task
to handle OOM situation but a3201227f803 (freezer: make freezing() test
freeze conditions in effect instead of TIF_FREEZE) has reorganized the
code and stopped clearing freeze flag in __thaw_task. This means that
the target task only wakes up and goes into the fridge again because the
freezing condition hasn't changed for it. This reintroduces the bug
fixed by f660daac474c6f.
Fix the issue by checking for TIF_MEMDIE thread flag in
freezing_slow_path and exclude the task from freezing completely. If a
task was already frozen it would get woken by __thaw_task from OOM killer
and get out of freezer after rechecking freezing().
Changes since v1
- put TIF_MEMDIE check into freezing_slowpath rather than in __refrigerator
as per Oleg
- return __thaw_task into oom_scan_process_thread because
oom_kill_process will not wake task in the fridge because it is
sleeping uninterruptible
[mhocko@suse.cz: rewrote the changelog] Fixes: a3201227f803 (freezer: make freezing() test freeze conditions in effect instead of TIF_FREEZE) Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Michal Hocko <mhocko@suse.cz> Acked-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we fail to load block bitmap in __ext4_new_inode() we will
dereference NULL pointer in ext4_journal_get_write_access(). So check
for error from ext4_read_block_bitmap().
Coverity-id: 989065 Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Code which changes policy to powersave changes also max_policy_pct based on
max_freq. Code which change max_perf_pct has upper limit base on value
max_policy_pct. When policy is changing from powersave back to performance
then max_policy_pct is not changed. Which means that changing max_perf_pct is
not possible to high values if max_freq was too low in powersave policy.
When there are no meta block groups update_backups() will compute the
backup block in 32-bit arithmetics thus possibly overflowing the block
number and corrupting the filesystem. OTOH filesystems without meta
block groups larger than 16 TB should be rare. Fix the problem by doing
the counting in 64-bit arithmetics.
Coverity-id: 741252 Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Lukas Czerner <lczerner@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the ext4_has_group_desc_csum predicate to look for a checksum
driver instead of the metadata_csum flag and change the bg checksum
calculation function to look for GDT_CSUM before taking the crc16
path.
Without this patch, if we mount with ^uninit_bg,^metadata_csum and
later metadata_csum gets turned on by accident, the block group
checksum functions will incorrectly assume that checksumming is
enabled (metadata_csum) but that crc16 should be used
(!s_chksum_driver). This is totally wrong, so fix the predicate
and the checksum formula selection.
(Granted, if the metadata_csum feature bit gets enabled on a live FS
then something underhanded is going on, but we could at least avoid
writing garbage into the on-disk fields.)
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Dmitry Monakhov <dmonakhov@openvz.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delalloc write journal reservations only reserve 1 credit,
to update the inode if necessary. However, it may happen
once in a filesystem's lifetime that a file will cross
the 2G threshold, and require the LARGE_FILE feature to
be set in the superblock as well, if it was not set already.
This overruns the transaction reservation, and can be
demonstrated simply on any ext4 filesystem without the LARGE_FILE
feature already set:
If there is a corrupted file system which has directory entries that
point at reserved, metadata inodes, prohibit them from being used by
treating them the same way we treat Boot Loader inodes --- that is,
mark them to be bad inodes. This prohibits them from being opened,
deleted, or modified via chmod, chown, utimes, etc.
In particular, this prevents a corrupted file system which has a
directory entry which points at the journal inode from being deleted
and its blocks released, after which point Much Hilarity Ensues.
The check whether quota format is set even though there are no
quota files with journalled quota is pointless and it actually
makes it impossible to turn off journalled quotas (as there's
no way to unset journalled quota format). Just remove the check.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When loading extended attributes, check each entry's value offset to
make sure it doesn't collide with the entries.
Without this check it is easy to crash the kernel by mounting a
malicious FS containing a file with an EA wherein e_value_offs = 0 and
e_value_size > 0 and then deleting the EA, which corrupts the name
list.
(See the f_ea_value_crash test's FS image in e2fsprogs for an example.)
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 8393c524a25609 (MIPS: tlbex: Fix a missing statement for
HUGETLB), the TLB Refill handler was fixed so that non-OCTEON targets
would work properly with huge pages. The change was incorrect in that
it broke the OCTEON case.
In the non-octeon case there is a destructive test for the huge PTE
bit, and then at 0, $k0 is reloaded (that is what the 8393c524a25609
patch added).
In the octeon case, we modify k1 in the branch delay slot, but we
never need k0 again, so the new load is not needed, but since k1 is
modified, if we do the load, we load from a garbage location and then
get a nested TLB Refill, which is seen in userspace as either SIGBUS
or SIGSEGV (depending on the garbage).
The real fix is to only do this reloading if it is needed, and never
where it is harmful.
This patch fixes a bug in handling of SPC-3 PR Activate Persistence
across Target Power Loss (APTPL) logic where re-creation of state for
MappedLUNs from dynamically generated NodeACLs did not occur during
I_T Nexus establishment.
It adds the missing core_scsi3_check_aptpl_registration() call during
core_tpg_check_initiator_node_acl() -> core_tpg_add_node_to_devs() in
order to replay any pre-loaded APTPL metadata state associated with
the newly connected SCSI Initiator Port.
Cc: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During temporary resource starvation at lower transport layer, command
is placed on queue full retry path, which expose this problem. The TCM
queue full handling of SCF_TRANSPORT_TASK_SENSE currently sends the same
cmd twice to lower layer. The 1st time led to cmd normal free path.
The 2nd time cause Null pointer access.
This regression bug was originally introduced v3.1-rc code in the
following commit:
The code is currently riddled with "drop the hardware_lock to avoid a
deadlock" bugs that expose races. One of those races seems to expose a
valid warning in tcm_qla2xxx_clear_nacl_from_fcport_map. Add some
bandaid to it.
Signed-off-by: Joern Engel <joern@logfs.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
