7d375bffa524 ("sb_edac: Fix support for systems with two home agents per socket")
NUM_CHANNELS was changed to 8 and the channel space was renumerated to
handle EN, EP, and EX configurations.
The *_mci_bind_devs() functions - except for sbridge_mci_bind_devs() -
got a new device presence check in the form of saw_chan_mask. However,
sbridge_mci_bind_devs() still uses the NUM_CHANNELS for loop.
With the increase in NUM_CHANNELS, this loop fails at index 4 since
SB only has 4 TADs. This results in the following error on SB machines:
EDAC sbridge: Some needed devices are missing
EDAC sbridge: Couldn't find mci handler
EDAC sbridge: Couldn't find mci handle
This patch adapts the saw_chan_mask logic for sbridge_mci_bind_devs() as
well.
After this patch:
EDAC MC0: Giving out device to module sbridge_edac.c controller Sandy Bridge Socket#0: DEV 0000:3f:0e.0 (POLLED)
EDAC MC1: Giving out device to module sbridge_edac.c controller Sandy Bridge Socket#1: DEV 0000:7f:0e.0 (POLLED)
This commit is poorly justified, I can find not discusison in email,
and it clearly causes a problem.
If a device which is being recovered fails and is subsequently
re-added to an array, there could easily have been changes to the
array *before* the point where the recovery was up to. So the
recovery must start again from the beginning.
If a spare is being recovered and fails, then when it is re-added we
really should do a bitmap-based recovery up to the recovery-offset,
and then a full recovery from there. Before this reversion, we only
did the "full recovery from there" which is not corect. After this
reversion with will do a full recovery from the start, which is safer
but not ideal.
It will be left to a future patch to arrange the two different styles
of recovery.
Reported-and-tested-by: Nate Dailey <nate.dailey@stratus.com> Signed-off-by: NeilBrown <neilb@suse.com> Fixes: 7eb418851f32 ("md: allow a partially recovered device to be hot-added to an array.") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 566c09c53455 ("raid5: relieve lock contention in get_active_stripe()")
__find_stripe() is called under conf->hash_locks + hash.
But handle_stripe_clean_event() calls remove_hash() under
conf->device_lock.
Under some cirscumstances the hash chain can be circuited,
and we get an infinite loop with disabled interrupts and locked hash
lock in __find_stripe(). This leads to hard lockup on multiple CPUs
and following system crash.
I was able to reproduce this behavior on raid6 over 6 ssd disks.
The devices_handle_discard_safely option should be set to enable trim
support. The following script was used:
for i in `seq 1 32`; do
dd if=/dev/zero of=large$i bs=10M count=100 &
done
neilb: original was against a 3.x kernel. I forward-ported
to 4.3-rc. This verison is suitable for any kernel since
Commit: 59fc630b8b5f ("RAID5: batch adjacent full stripe write")
(v4.1+). I'll post a version for earlier kernels to stable.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru> Fixes: 566c09c53455 ("raid5: relieve lock contention in get_active_stripe()") Signed-off-by: NeilBrown <neilb@suse.com> Cc: Shaohua Li <shli@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was introduced with 9e882242c6193ae6f416f2d8d8db0d9126bd996b
which changed the return value of submit_bio_wait() to return != 0 on
error, but didn't update the caller accordingly.
This was introduced with 9e882242c6193ae6f416f2d8d8db0d9126bd996b
which changed the return value of submit_bio_wait() to return != 0 on
error, but didn't update the caller accordingly.
Currently a number of Crypto API operations may fail when a signal
occurs. This causes nasty problems as the caller of those operations
are often not in a good position to restart the operation.
In fact there is currently no need for those operations to be
interrupted by user signals at all. All we need is for them to
be killable.
This patch replaces the relevant calls of signal_pending with
fatal_signal_pending, and wait_for_completion_interruptible with
wait_for_completion_killable, respectively.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92bac83dd79e ("Input: alps - non interleaved V2 dualpoint has
separate stick button bits") assumes that all alps v2 non-interleaved
dual point setups have the separate stick button bits.
Later we limited this to Dell laptops only because of reports that this
broke things on non Dell laptops. Now it turns out that this breaks things
on the Dell Latitude D600 too. So it seems that only the Dell Latitude
D420/430/620/630, which all share the same touchpad / stick combo,
have these separate bits.
This patch limits the checking of the separate bits to only these models
fixing regressions with other models.
Reported-and-tested-by: Larry Finger <Larry.Finger@lwfinger.net> Tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-By: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If two overlayfs filesystems are stacked on top of each other, then we need
recursion in ovl_d_select_inode().
I guess d_backing_inode() is supposed to do that. But currently it doesn't
and that functionality is open coded in vfs_open(). This is now copied
into ovl_d_select_inode() to fix this regression.
Reported-by: Alban Crequy <alban.crequy@gmail.com> Signed-off-by: Miklos Szeredi <miklos@szeredi.hu> Fixes: 4bacc9c9234c ("overlayfs: Make f_path always point to the overlay...") Cc: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ovl_copy_up_locked(), newdentry is leaked if the function exits through
out_cleanup as this just to out after calling ovl_cleanup() - which doesn't
actually release the ref on newdentry.
The out_cleanup segment should instead exit through out2 as certainly
newdentry leaks - and possibly upper does also, though this isn't caught
given the catch of newdentry.
Without this fix, something like the following is seen:
Open the lower file with O_LARGEFILE in ovl_copy_up().
Pass O_LARGEFILE unconditionally in ovl_copy_up_data() as it's purely for
catching 32-bit userspace dealing with a file large enough that it'll be
mishandled if the application isn't aware that there might be an integer
overflow. Inside the kernel, there shouldn't be any problems.
63692df103e9 ("PCI: Allow numa_node override via sysfs") didn't check that
the numa node provided by userspace is valid. Passing a node number too
high would attempt to access invalid memory and trigger a kernel panic.
Laura Abbott <labbott@redhat.com> produced a patch which lead us to
inspect symbol_put_addr(). This function has a comment claiming it
doesn't need to disable preemption around the module lookup
because it holds a reference to the module it wants to find, which
therefore cannot go away.
This is wrong (and a false optimization too, preempt_disable() is really
rather cheap, and I doubt any of this is on uber critical paths,
otherwise it would've retained a pointer to the actual module anyway and
avoided the second lookup).
While its true that the module cannot go away while we hold a reference
on it, the data structure we do the lookup in very much _CAN_ change
while we do the lookup. Therefore fix the comment and add the
required preempt_disable().
xen-blkfront will crash if the check to talk_to_blkback()
in blkback_changed()(XenbusStateInitWait) returns an error.
The driver data is freed and info is set to NULL. Later during
the close process via talk_to_blkback's call to xenbus_dev_fatal()
the null pointer is passed to and dereference in blkfront_closing.
We received several reports of systems rebooting and powering on
after an attempted shutdown. Testing showed that setting
XHCI_SPURIOUS_WAKEUP quirk in addition to the XHCI_SPURIOUS_REBOOT
quirk allowed the system to shutdown as expected for LynxPoint-LP
xHCI controllers. Set the quirk back.
Note that the quirk was originally introduced for LynxPoint and
LynxPoint-LP just for this same reason. See:
commit 638298dc66ea ("xhci: Fix spurious wakeups after S5 on Haswell")
It was later limited to only concern HP machines as it caused
regression on some machines, see both bug and commit:
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66171
commit 6962d914f317 ("xhci: Limit the spurious wakeup fix only to HP machines")
Later it was discovered that the powering on after shutdown
was limited to LynxPoint-LP (Haswell-ULT) and that some non-LP HP
machine suffered from spontaneous resume from S3 (which should
not be related to the SPURIOUS_WAKEUP quirk at all). An attempt
to fix this then removed the SPURIOUS_WAKEUP flag usage completely.
commit b45abacde3d5 ("xhci: no switching back on non-ULT Haswell")
Current understanding is that LynxPoint-LP (Haswell ULT) machines
need the SPURIOUS_WAKEUP quirk, otherwise they will restart, and
plain Lynxpoint (Haswell) machines may _not_ have the quirk
set otherwise they again will restart.
Signed-off-by: Laura Abbott <labbott@fedoraproject.org> Cc: Takashi Iwai <tiwai@suse.de> Cc: Oliver Neukum <oneukum@suse.com>
[Added more history to commit message -Mathias] Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a host fails to wake up a isochronous SuperSpeed device from U1/U2
in time for a isoch transfer it will generate a "No ping response error"
Host will then move to the next transfer descriptor.
Handle this case in the same way as missed service errors, tag the
current TD as skipped and handle it on the next transfer event.
a PPC64LE kernel fails to boot when fbcon_add_cursor_timer uses an
uninitialized ops->cur_blink_jiffies. Prevent by initializing
in fbcon_init before the call to info->fbops->fb_set_par.
clk_add_alias() was not correctly handling the case where alias_dev_name
was NULL: rather than producing an entry with a NULL dev_id pointer,
it would produce a device name of (null). Fix this.
Fixes: 2568999835d7 ("clkdev: add clkdev_create() helper") Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 00d8689b85a7 ("i2c: mv64xxx: rework offload support to fix
several problems") completely reworked the offload support, but left a
debugging-related "return false" at the beginning of the
mv64xxx_i2c_can_offload() function. This has the unfortunate consequence
that offloading is in fact never used, which wasn't really the
intention.
This commit fixes that problem by removing the bogus "return false".
Fixes: 00d8689b85a7 ("i2c: mv64xxx: rework offload support to fix several problems") Signed-off-by: Hezi Shahmoon <hezi@marvell.com>
[Thomas: reworked commit log and title.] Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit prevents from sending "big" file using Bluetooth.
When sending a lot of data quickly through the Bluetooth interface, and
after a variable amount of data sent, transfer fails with error:
kernel: [ 415.247453] Bluetooth: hci0 hardware error 0x00
Found on T100TA.
After reverting this commit, send works fine for any file size.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com> Fixes: 9119fba0cfed (serial: 8250_dma: don't bother DMA with small transfers) Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compiling the nvme driver on 32-bit warns about a cast from a __u64
variable to a pointer:
drivers/block/nvme-core.c: In function 'nvme_submit_io':
drivers/block/nvme-core.c:1847:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void __user *)io.addr, length, NULL, 0);
The cast here is intentional and safe, so we can shut up the
gcc warning by adding an intermediate cast to 'uintptr_t'.
I had previously submitted a patch to fix this problem in the
nvme driver, but it was accepted on the same day that two new
warnings got added.
For clarification, I also change the third instance of this cast
to use uintptr_t instead of unsigned long now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: d29ec8241c10e ("nvme: submit internal commands through the block layer") Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
btree_split_beneath()'s error path had an outstanding FIXME that speaks
directly to the potential for _not_ cleaning up a previously allocated
bufio-backed block.
Fix this by releasing the previously allocated bufio block using
unlock_block().
Reported-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Acked-by: Joe Thornber <thornber@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the CLEAN_SHUTDOWN flag is not set when a cache is loaded then all cache
blocks are marked as dirty and a full writeback occurs.
__commit_transaction() is responsible for setting/clearing
CLEAN_SHUTDOWN (based the flags_mutator that is passed in).
Fix this issue, of the cache's on-disk flags being wrong, by making sure
__commit_transaction() does not reset the flags after the mutator has
altered the flags in preparation for them being serialized to disk.
Commit 4c7e309340ff ("dm btree remove: fix bug in redistribute3") wasn't
a complete fix for redistribute3().
The redistribute3 function takes 3 btree nodes and shares out the entries
evenly between them. If the three nodes in total contained
(MAX_ENTRIES * 3) - 1 entries between them then this was erroneously getting
rebalanced as (MAX_ENTRIES - 1) on the left and right, and (MAX_ENTRIES + 1) in
the center.
Fix this issue by being more careful about calculating the target number
of entries for the left and right nodes.
Unit tested in userspace using this program:
https://github.com/jthornber/redistribute3-test/blob/master/redistribute3_t.c
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bdi's are initialized in two steps, bdi_init() and bdi_register(), but
destroyed in a single step by bdi_destroy() which, for a bdi embedded
in a request_queue, is called during blk_cleanup_queue() which makes
the queue invisible and starts the draining of remaining usages.
A request_queue's user can access the congestion state of the embedded
bdi as long as it holds a reference to the queue. As such, it may
access the congested state of a queue which finished
blk_cleanup_queue() but hasn't reached blk_release_queue() yet.
Because the congested state was embedded in backing_dev_info which in
turn is embedded in request_queue, accessing the congested state after
bdi_destroy() was called was fine. The bdi was destroyed but the
memory region for the congested state remained accessible till the
queue got released.
a13f35e87140 ("writeback: don't embed root bdi_writeback_congested in
bdi_writeback") changed the situation. Now, the root congested state
which is expected to be pinned while request_queue remains accessible
is separately reference counted and the base ref is put during
bdi_destroy(). This means that the root congested state may go away
prematurely while the queue is between bdi_dstroy() and
blk_cleanup_queue(), which was detected by Andrey's KASAN tests.
The root cause of this problem is that bdi doesn't distinguish the two
steps of destruction, unregistration and release, and now the root
congested state actually requires a separate release step. To fix the
issue, this patch separates out bdi_unregister() and bdi_exit() from
bdi_destroy(). bdi_unregister() is called from blk_cleanup_queue()
and bdi_exit() from blk_release_queue(). bdi_destroy() is now just a
simple wrapper calling the two steps back-to-back.
While at it, the prototype of bdi_destroy() is moved right below
bdi_setup_and_register() so that the counterpart operations are
located together.
Signed-off-by: Tejun Heo <tj@kernel.org> Fixes: a13f35e87140 ("writeback: don't embed root bdi_writeback_congested in bdi_writeback") Reported-and-tested-by: Andrey Konovalov <andreyknvl@google.com> Link: http://lkml.kernel.org/g/CAAeHK+zUJ74Zn17=rOyxacHU18SgCfC6bsYW=6kCY5GXJBwGfQ@mail.gmail.com Reviewed-by: Jan Kara <jack@suse.com> Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit dd006da21646 ("arm64: mm: increase VA range of identity map")
introduced a mechanism to extend the virtual memory map range
to support arm64 systems with system RAM located at very high offset,
where the identity mapping used to enable/disable the MMU requires
additional translation levels to map the physical memory at an equal
virtual offset.
The kernel detects at boot time the tcr_el1.t0sz value required by the
identity mapping and sets-up the tcr_el1.t0sz register field accordingly,
any time the identity map is required in the kernel (ie when enabling the
MMU).
After enabling the MMU, in the cold boot path the kernel resets the
tcr_el1.t0sz to its default value (ie the actual configuration value for
the system virtual address space) so that after enabling the MMU the
memory space translated by ttbr0_el1 is restored as expected.
Commit dd006da21646 ("arm64: mm: increase VA range of identity map")
also added code to set-up the tcr_el1.t0sz value when the kernel resumes
from low-power states with the MMU off through cpu_resume() in order to
effectively use the identity mapping to enable the MMU but failed to add
the code required to restore the tcr_el1.t0sz to its default value, when
the core returns to the kernel with the MMU enabled, so that the kernel
might end up running with tcr_el1.t0sz value set-up for the identity
mapping which can be lower than the value required by the actual virtual
address space, resulting in an erroneous set-up.
This patchs adds code in the resume path that restores the tcr_el1.t0sz
default value upon core resume, mirroring this way the cold boot path
behaviour therefore fixing the issue.
Cc: Catalin Marinas <catalin.marinas@arm.com> Fixes: dd006da21646 ("arm64: mm: increase VA range of identity map") Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this patch applied, we were the only architecture making this sort
of adjustment to the PC calculation in the unwinder. This causes
problems for ftrace, where the PC values are matched against the
contents of the stack frames in the callchain and fail to match any
records after the address adjustment.
Whilst there has been some effort to change ftrace to workaround this,
those patches are not yet ready for mainline and, since we're the odd
architecture in this regard, let's just step in line with other
architectures (like arch/arm/) for now.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8a603f91cc48 ("ARM: 8445/1: fix vdsomunge not to depend on
glibc specific byteswap.h") unfortunately introduced a bug created but
not found during discussion and patch simplification.
Reported-by: Efraim Yawitz <efraim.yawitz@gmail.com> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Fixes: 8a603f91cc48 ("ARM: 8445/1: fix vdsomunge not to depend on glibc specific byteswap.h") Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 685e2d08c54b ("ARM: OMAP1: Change interrupt numbering for
sparse IRQ") turned on SPARSE_IRQ on OMAP1, but forgot to change
the number of INT_DMA_LCD. This broke the boot at least on Nokia 770,
where the device hangs during framebuffer initialization.
Fix by defining INT_DMA_LCD like the other interrupts.
Fixes: 685e2d08c54b ("ARM: OMAP1: Change interrupt numbering for sparse IRQ") Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d8aca9df612f5751892fb2642d72536f2f48fd0
"ARM: ux500: fix MMC/SD card regression"
fixed broken the level shifter: it should be default ON
but became default OFF.
LDO1 regulator (VDD_SD) is connected to SoC's vddshv8. vddshv8 needs to
be kept always powered (see commit 5a0f93c6576a ("ARM: dts: Add
am57xx-beagle-x15"), but at the moment VDD_SD is enabled/disabled
depending on whether an SD card is inserted or not.
This patch sets LDO1 regulator to always-on.
This patch has a side effect of fixing another issue, HDMI DDC not
working when SD card is not inserted:
Why this happens is that the tpd12s015 (HDMI level shifter/ESD
protection chip) has LS_OE GPIO input, which needs to be enabled for the
HDMI DDC to work. LS_OE comes from gpio6_28. The pin that provides
gpio6_28 is powered by vddshv8, and vddshv8 comes from VDD_SD.
So when SD card is not inserted, VDD_SD is disabled, and LS_OE stays
off.
The proper fix for the HDMI DDC issue would be to maybe have the pinctrl
framework manage the pin specific power.
Apparently this fixes also a third issue (copy paste from Kishon's
patch):
ldo1_reg in addition to being connected to the io lines is also
connected to the card detect line. On card removal, omap_hsmmc
driver does a regulator_disable causing card detect line to be
pulled down. This raises a card insertion interrupt and once the
MMC core detects there is no card inserted, it does a
regulator disable which again raises a card insertion interrupt.
This happens in a loop causing infinite MMC interrupts.
Fixes: 5a0f93c6576a ("ARM: dts: Add am57xx-beagle-x15") Cc: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reported-by: Louis McCarthy <compeoree@gmail.com> Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, BG2Q shares a compatible with BG2. This is incorrect, since
BG2 and BG2Q use different USB PLL dividers. In reality, BG2Q shares a
divider with BG2CD. Change BG2Q's USB PHY compatible string to reflect
that.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com> Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit enables standby support on Armada 385 DB-AP board, because
the PM initalization routine requires "marvell,armada380" compatible
string for all Armada 38x-based platforms.
Beside the compatible "marvell,armada38x" was wrong and should be fixed
in the stable kernels too.
[gregory.clement@free-electrons.com: add information, about the fixes] Fixes: e5ee12817e9ea ("ARM: mvebu: Add Armada 385 Access Point
Development Board support") Signed-off-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DSA expects the host_dev pointer to be the device structure associated
with the MDIO bus controller driver. First commit breaking that was c3a07134e6aa ("mv643xx_eth: convert to use the Marvell Orion MDIO
driver"), and then, it got completely under the radar for a while.
Reported-by: Frans van de Wiel <fvdw@fvdw.eu> Fixes: c3a07134e6aa ("mv643xx_eth: convert to use the Marvell Orion MDIO driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On each next iteration of for_each_compatible_node() the reference
counter for current device node is already decreased by the loop
iterator. The manual call to of_node_get() is required only on loop
break which is not happening here.
The double of_node_get() (with enabled CONFIG_OF_DYNAMIC) lead to
decreasing the counter below expected, initial value.
Fixes: fe4034a3fad7 ("ARM: EXYNOS: Add missing of_node_put() when parsing power domains") Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Kukjin Kim <kgene@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mapping an image with a long parent chain (e.g. image foo, whose parent
is bar, whose parent is baz, etc) currently leads to a kernel stack
overflow, due to the following recursion in the reply path:
Currently we leak parent_spec and trigger a "parent reference
underflow" warning if rbd_dev_create() in rbd_dev_probe_parent() fails.
The problem is we take the !parent out_err branch and that only drops
refcounts; parent_spec that would've been freed had we called
rbd_dev_unparent() remains and triggers rbd_warn() in
rbd_dev_parent_put() - at that point we have parent_spec != NULL and
parent_ref == 0, so counter ends up being -1 after the decrement.
rbd requires stable pages, as it performs a crc of the page data before
they are send to the OSDs.
But since kernel 3.9 (patch 1d1d1a767206fbe5d4c69493b7e6d2a8d08cc0a0
"mm: only enforce stable page writes if the backing device requires
it") it is not assumed anymore that block devices require stable pages.
This patch sets the necessary flag to get stable pages back for rbd.
In a ceph installation that provides multiple ext4 formatted rbd
devices "bad crc" messages appeared regularly (ca 1 message every 1-2
minutes on every OSD that provided the data for the rbd) in the
OSD-logs before this patch. After this patch this messages are pretty
much gone (only ca 1-2 / month / OSD).
Signed-off-by: Ronny Hegewald <Ronny.Hegewald@online.de>
[idryomov@gmail.com: require stable pages only in crc case, changelog]
[idryomov@gmail.com: backport to 3.18-4.2: context] Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This accelerometer accidentally either emits a DRDY signal or an
IRQ signal. Accidentally I activated the IRQ signal as I thought
it was analogous to the interrupt generator on other ST
accelerometers. This was wrong. After this patch generic_buffer
gives a nice stream of accelerometer readings.
Fixes: 3acddf74f807778f "iio: st-sensors: add support for lis3lv02d accelerometer" Cc: Denis CIOCCA <denis.ciocca@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pinning a userptr onto the hardware raises interesting questions about
the lifetime of such a surface as the framebuffer extends that life
beyond the client's address space. That is the hardware will need to
keep scanning out from the backing storage even after the client wants
to remap its address space. As the hardware pins the backing storage,
the userptr becomes invalid and this raises a WARN when the clients
tries to unmap its address space. The situation can be even more
complicated when the buffer is passed between processes, between a
client and display server, where the lifetime and hardware access is
even more confusing. Deny it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Michał Winiarski <michal.winiarski@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We accidentally lost the initial DPLL register write in 1c4e02746147 drm/i915: Fix DVO 2x clock enable on 830M
The "three times for luck" hack probably saved us from a total
disaster. But anyway, bring the initial write back so that the
code actually makes some sense.
Reported-and-tested-by: Nick Bowler <nbowler@draconx.ca>
References: http://mid.gmane.org/CAN_QmVyMaArxYgEcVVsGvsMo7-6ohZr8HmF5VhkkL4i9KOmrhw@mail.gmail.com Cc: Nick Bowler <nbowler@draconx.ca> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to flush the results from in-batch pipecontrol writes (used for
example in glQuery) before declaring the batch complete (and so declaring
the query results coherent), we need to set the FlushEnable bit in our
flushing pipecontrol. The FlushEnable bit "waits until all previous
writes of immediate data from post-sync circles are complete before
executing the next command".
I get GPU hangs on byt without flushing these writes (running ue4).
piglit has examples where the flush is required for correct rendering.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Acked-by: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On nv50+, we restrict the valid domains to just the one where the buffer
was originally created. However after the buffer is evicted to system
memory, we might move it back to a different domain that was not
originally valid. When sharing the buffer and retrieving its GEM_INFO
data, we still want the domain that will be valid for this buffer in a
pushbuf, not the one where it currently happens to be.
This resolves fdo#92504 and several others. These are due to suspend
evicting all buffers, making it more likely that they temporarily end up
in the wrong place.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92504 Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When PMU context is migrating between CPUs, interrupt affinity is set as
well. Only this should not happen when the CCN interrupt is not being
used at all (the driver is using a hrtimer tick instead).
The reason is that the stack tracer traces all function calls, and some of
those calls happen while exiting or entering user space and idle. Some of
these functions are called after RCU had already stopped watching, as RCU
does not watch userspace or idle CPUs.
If a max stack is hit, then the save_stack_trace() is called, which will
check module addresses and call module_assert_mutex_or_preempt(), and then
trigger the warning. Sad part is, the warning itself will also do a stack
trace and tigger the same warning. That probably should be fixed.
The warning was added by 0be964be0d45 "module: Sanitize RCU usage and
locking" but this bug has probably been around longer. But it's unlikely to
cause much harm, but the new warning causes the system to lock up.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc:"Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now you should not ask kernel to do a stupid stuff like copying 256MB in
2-byte chunks and call fsync(2) after each chunk but if you do, sysadmin
should have a way to stop you.
We actually do have a check for fatal_signal_pending() in
generic_perform_write() which triggers in this path however because we
always succeed in writing something before the check is done, we return
value > 0 from generic_perform_write() and thus the information about
signal gets lost.
Fix the problem by doing the signal check before writing anything. That
way generic_perform_write() returns -EINTR, the error gets propagated up
and the sendfile loop terminates early.
Signed-off-by: Jan Kara <jack@suse.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4857c91f0d19 changed the way how irq affinity is setup in
setup_ioapic_dest() from using the core helper function to
unconditionally calling the irq_set_affinity() callback of the
underlying irq chip.
That results in a NULL pointer dereference for the rare case where the
underlying irq chip is lapic_chip which has no irq_set_affinity()
callback. lapic_chip is occasionally used for the timer interrupt (irq
0).
The fix is simple: Check the availability of the callback instead of
calling it unconditionally.
Fixes: 4857c91f0d19 "x86/ioapic: Force affinity setting in setup_ioapic_dest()" Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When multiple GOP devices exists, but none of them implements
ConOut, the code should just choose the first GOP (according to
the comments). But currently 'fb_base' will refer to the last GOP,
while other parameters to the first GOP, which will likely
result in a garbled display.
I can reliably reproduce this bug using my ASRock Z87M Extreme4
motherboard with CSM and integrated GPU disabled, and two PCIe
video cards (NVidia GT640 and GTX980), booting from efi-stub
(booting from grub works fine). On the primary display the
ASRock logo remains and on the secondary screen it is garbled
up completely.
Signed-off-by: Kővágó, Zoltán <DirtY.iCE.hu@gmail.com> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1444659236-24837-2-git-send-email-matt@codeblueprint.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are 24 EQ registers not 25, I suspect this bug came about because
the registers start at EQ1 not zero. The bug is relatively harmless as
the extra register written is an unused one.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SX_TLV controls are intended for situations where the register behind
the control has some non-zero value indicating the minimum gain
and then gains increasing from there and eventually overflowing through
zero.
Currently every CODEC implementing these controls specifies the minimum
as the non-zero value for the minimum and the maximum as the number of
gain settings available.
This means when the info callback subtracts the minimum value from the
maximum value to calculate the number of gain levels available it is
actually under reporting the available levels. This patch fixes this
issue by adding a new snd_soc_info_volsw_sx callback that does not
subtract the minimum value.
Fixes: 1d99f2436d0d ("ASoC: core: Rework SOC_DOUBLE_R_SX_TLV add SOC_SINGLE_SX_TLV") Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Acked-by: Brian Austin <brian.austin@cirrus.com> Tested-by: Brian Austin <brian.austin@cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compiling the hdac extended core on arm fails with below error:
sound/hda/ext/hdac_ext_bus.c: In function 'hdac_ext_writel':
>> sound/hda/ext/hdac_ext_bus.c:29:2: error: implicit declaration of
>> function
+'writel' [-Werror=implicit-function-declaration]
writel(value, addr);
^
sound/hda/ext/hdac_ext_bus.c: In function 'hdac_ext_readl':
>> sound/hda/ext/hdac_ext_bus.c:34:2: error: implicit declaration of
>> function
+'readl' [-Werror=implicit-function-declaration]
return readl(addr);
This is fixed by explicitly including io.h
Fixes: 99463b3a3994 - ('ALSA: hda: provide default bus io ops extended hdac') Reported-by: kbuild test robot <lkp@intel.com> Suggested-by: Mark Brown <broonie@kernel.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vgic code on ARM is built for all configurations that enable KVM,
but the parent_data field that it references is only present when
CONFIG_IRQ_DOMAIN_HIERARCHY is set:
virt/kvm/arm/vgic.c: In function 'kvm_vgic_map_phys_irq':
virt/kvm/arm/vgic.c:1781:13: error: 'struct irq_data' has no member named 'parent_data'
This flag is implied by the GIC driver, and indeed the VGIC code only
makes sense if a GIC is present. This changes the CONFIG_KVM symbol
to always select GIC, which avoids the issue.
Add lock to prevent concurrent access for control message as control
message function uses shared buffer. Without the lock there may be
remote control polling which messes the buffer causing IO errors.
Increase buffer size and add check for maximum supported message
length.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=103391 Fixes: c56222a6b25c ("[media] rtl28xxu: move usb buffers to state") Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading the firmware and sending commands, the length must
be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the expected
format:
si2168 11-0064: found a 'Silicon Labs Si2168-B40'
si2168 11-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 11-0064: firmware download failed -95
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ffffffffa085708f
Add the proper check.
Reported-by: Stuart Auchterlonie <sauchter@redhat.com> Reviewed-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Laura Abbott <labbott@fedoraproject.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading the firmware and sending commands, the length
must be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the
expected format. Add the proper check.
Device stopped to tuning some channels after regmap conversion.
Reason is that regmap_update_bits() works a bit differently for
partially volatile registers than old homemade routine. Return
back to old routine in order to fix issue.
Fixes: 478932b16052f5ded74685d096ae920cd17d6424 Reported-by: Mark Clarkstone <hello@markclarkstone.co.uk> Tested-by: Mark Clarkstone <hello@markclarkstone.co.uk> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Maneet Singh <mmaneetsingh@nvidia.com>
[seanpaul tweaked commit subject a little] Signed-off-by: Sean Paul <seanpaul@chromium.org> Reviewed-by: Daniel Stone <daniels@collabora.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Dave Airlie <airlied@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Linux 4.3-rc5, there is an error case in drm_dp_get_branch_device
that returns without releasing mgr->lock, resulting a spew of kernel
messages about a kernel work function possibly having leaked a mutex
and presumably more serious adverse consequences later. This patch
changes the error to "goto out" to unlock the mutex before returning.
[airlied: grabbed from drm-next as it fixes something we've seen]
Signed-off-by: Adam J. Richter <adam_richter2004@yahoo.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we do not validate rtas.entry before calling enter_rtas(). This
leads to a kernel oops when user space calls rtas system call on a powernv
platform (see below). This patch adds code to validate rtas.entry before
making enter_rtas() call.
During device assignment/deassignment the flags in the DTE
get lost, which might cause spurious faults, for example
when the device tries to access the system management range.
Fix this by not clearing the flags with the rest of the DTE.
Reported-by: G. Richard Bellamy <rbellamy@pteradigm.com> Tested-by: G. Richard Bellamy <rbellamy@pteradigm.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mm/memory.c
3147 static int do_numa_page(struct mm_struct *mm, struct vm_area_struct *vma,
....
3159 /* A PROT_NONE fault should not end up here */
3160 BUG_ON(!(vma->vm_flags & (VM_READ | VM_EXEC | VM_WRITE)));
In preparation for the installation of a large page, any small page
tables that may still exist in the target IOV address range are
removed. However, if a scatter/gather list entry is large enough to
fit more than one large page, the address space for any subsequent
large pages is not cleared of conflicting small page tables.
This can cause legitimate mapping requests to fail with errors of the
form below, potentially followed by a series of IOMMU faults:
ERROR: DMA PTE for vPFN 0xfde00 already set (to 7f83a4003 not 7e9e00083)
In this example, a 4MiB scatter/gather list entry resulted in the
successful installation of a large page @ vPFN 0xfdc00, followed by
a failed attempt to install another large page @ vPFN 0xfde00, due to
the presence of a pointer to a small page table @ 0x7f83a4000.
To address this problem, compute the number of large pages that fit
into a given scatter/gather list entry, and use it to derive the
last vPFN covered by the large page(s).
Signed-off-by: Christian Zander <christian@nervanasys.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FW dump may be triggered when running init ucode, for example due to a
sysassert. In this case fw_dump_wk may run after mvm is freed, resulting
in a kernel panic.
Fix it by flushing the work.
Fixes: 01b988a708af ("iwlwifi: mvm: allow to collect debug data when restart is disabled") Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the CT-kill exit flow, the card is powered up and partially
initialized to check if the temperature is already low enough.
Unfortunately the init bails early because the CT-kill flag is set.
Make the code bail early only for HW RF-kill, as was intended by the
author. CT-kill is self-imposed and is not really RF-kill.
The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.
When going into/coming out of D3, the TX PN must be programmed into
and restored from the firmware respectively. The restore was broken
due to my previous commit to move PN assignment into the driver.
Sending the PN to the firmware still worked since we now use the
counter that's shared with mac80211, but accessing it through the
mac80211 API makes no sense now.
Fix this by reading/writing the counter directly. This actually
simplifies the code since we don't need to round-trip through the
key_seq structure.
Fixes: ca8c0f4bede6 ("iwlwifi: mvm: move TX PN assignment for CCMP to the driver") Reported-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The csa_countdown flag was not cleared when the AP is stopped.
As a result, if the AP was stopped after csa_countdown had started,
all the folowing channel switch commands would fail.
Fix that by clearing the csa_countdown flag when the AP is stopped.
In commit 1277fa2ab2f9 ("rtlwifi: Remove the clear interrupt routine from all
drivers"), the code that cleared all interrupt enable bits before setting them
was removed for all PCI drivers. This fixed an issue that caused TX to be
blocked for 3-5 seconds. On some RTL8821AE units, this change causes soft
lockups to occur on boot. For that reason, the portion of the earlier commit
that applied to rtl8821ae is reverted. Kernels 4.1 and newer are affected.
See http://marc.info/?l=linux-wireless&m=144373370103285&w=2 and
https://bugzilla.opensuse.org/show_bug.cgi?id=944978 for two cases where
this regression affected user systems. Note that this bug does not appear on
any of the developer's setups. For those users whose systems are affected
by the TX blockage, but do not lock up on boot, a module parameter is added
to disable the interrupt clear
Fixes: 1277fa2ab2f9 ("rtlwifi: Remove the clear interrupt routine from all drivers") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MODULE_FIRMWARE() for 3160 should be using the 7260 version as
it's done in the device configuration struct instead of referencing
IWL3160_UCODE_API_OK which doesn't even exist.
The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.
Suppose that we got a data crc error, and it triggers the mmc_reset.
mmc_reset will call mmc_send_status to see if HW reset was supported.
before issue CMD13, it will do retune, and if EMMC was in HS400 mode,
it will reduce frequency to 52Mhz firstly, then results in card init
was doing at 52Mhz.
The mmc_send_status was originally only done for mmc_test, should drop
it. And, rename the "eMMC hardware reset" to "Reset test", as we would
also be able to use the test for SD-cards.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> Suggested-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: bd11e8bd03ca ("mmc: core: Flag re-tuning is needed on CRC errors") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ath9k inserts padding between the 802.11 header and the data area (to
align it). Since it didn't declare this extra required headroom, this
led to some nasty issues like randomly dropped packets in some setups.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 30686bf7f5b3 ("mac80211: convert HW flags to unsigned long
bitmap") accidentally removed the newline delimiter from the hwflags
debugfs file. Fix this by adding back the newline between the HW flags.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
[fix commit log] Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The server rdma_read_chunk_lcl() and rdma_read_chunk_frmr() functions
were not taking into account the initial page_offset when determining
the rdma read length. This resulted in a read who's starting address
and length exceeded the base/bounds of the frmr.
The server gets an async error from the rdma device and kills the
connection, and the client then reconnects and resends. This repeats
indefinitely, and the application hangs.
Most work loads don't tickle this bug apparently, but one test hit it
every time: building the linux kernel on a 16 core node with 'make -j
16 O=/mnt/0' where /mnt/0 is a ramdisk mounted via NFSRDMA.
This bug seems to only be tripped with devices having small fastreg page
list depths. I didn't see it with mlx4, for instance.
Fixes: 0bf4828983df ('svcrdma: refactor marshalling logic') Signed-off-by: Steve Wise <swise@opengridcomputing.com> Tested-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
6910fa1 ("arm64: enable PTE type bit in the mask for pte_modify") fixes
a problem whereby a large block of PROT_NONE mapped memory is
incorrectly mapped as block descriptors when mprotect is called.
Unfortunately, a subtle bug was introduced by this fix to the THP logic.
If one mmaps a large block of memory, then faults it such that it is
collapsed into THPs; resulting calls to mprotect on this area of memory
will lead to incorrect table descriptors being written instead of block
descriptors. This is because pmd_modify calls pte_modify which is now
allowed to modify the type of the page table entry.
This patch reverts commit 6910fa16dbe142f6a0fd0fd7c249f9883ff7fc8a, and
fixes the problem it was trying to address by adjusting PAGE_NONE to
represent a table entry. Thus no change in pte type is required when
moving from PROT_NONE to a different protection.
Fixes: 6910fa16dbe1 ("arm64: enable PTE type bit in the mask for pte_modify") Cc: <stable@vger.kernel.org> # 4.0+ Cc: Feng Kan <fkan@apm.com> Reported-by: Ganapatrao Kulkarni <Ganapatrao.Kulkarni@caviumnetworks.com> Tested-by: Ganapatrao Kulkarni <gkulkarni@caviumnetworks.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
[SteveC: backported 1a541b4e3cd6f5795022514114854b3e1345f24e to 4.1 and
4.2 stable. Just one minor fix to second part to allow patch to apply
cleanly, no logic changed.] Signed-off-by: Steve Capper <steve.capper@linaro.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
timekeeping_init() can set the wall time offset, so we need to
increment the clock_was_set_seq counter. That way hrtimers will pick
up the early offset immediately. Otherwise on a machine which does not
set wall time later in the boot process the hrtimer offset is stale at
0 and wall time timers are going to expire with a delay of 45 years.
Fixes: 868a3e915f7f "hrtimer: Make offset update smarter" Reported-and-tested-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Stefan Liebler <stli@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If rbd_dev_image_probe() in rbd_dev_probe_parent() fails, header_name
is freed twice: once in rbd_dev_probe_parent() and then in its caller
rbd_dev_image_probe() (rbd_dev_image_probe() is called recursively to
handle parent images).
rbd_dev_probe_parent() is responsible for probing the parent, so it
shouldn't muck with clone's fields.
This fixes flickering issues caused by prematurely firing pflip
interrupts.
v2 (chk): add commit message, fix DCE V10/V11 and DM as well
v3: Re-enable pflip interrupt wherever we re-enable a CRTC
v4: Enable pflip interrupt in DAL as well
v5: drop DAL changes for upstream
v6: (agd): only enable interrupts on crtcs that exist
v7: (agd): integrate suggestions from Michel
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we are not the root device before attempting to
read the pcie bridge registers to check the pcie gen speeed.
Fixes a crash when the device is passed through to a VM.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
