The previous fix for filtering out of unwatched events was not entirely
correct. Instead of skipping the events we don't want, they are now
interpreted as events with opposing edge.
In order to fix it: always read the GPIO line value on interrupt and
only emit the event if it corresponds with the event type we requested.
The number of pins in South Bridge is 30 and not 29. There is a fix for
the driver for the pinctrl, but a fix is also need at device tree level
for the GPIO.
Fixes: afda007feda5 ("ARM64: dts: marvell: Add pinctrl nodes for Armada
3700") Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IRTE[GALogIntr] bit should set when enabling guest_mode, which enables
IOMMU to generate entry in GALog when IRTE[IsRun] is not set, and send
an interrupt to notify IOMMU driver.
If the decrementer wraps again and de-asserts the decrementer
exception while hard-disabled, __check_irq_replay() has a test to
notice the wrap when interrupts are re-enabled.
The decrementer check must be done when clearing the PACA_IRQ_HARD_DIS
flag, not when the PACA_IRQ_DEC flag is tested. Previously this worked
because the decrementer interrupt was always the first one checked
after clearing the hard disable flag, but HMI check was moved ahead of
that, which introduced this bug.
This can cause a missed decrementer interrupt if we soft-disable
interrupts then take an HMI which is recorded in irq_happened, then
hard-disable interrupts for > 4s to wrap the decrementer.
Fixes: e0e0d6b7390b ("powerpc/64: Replay hypervisor maintenance interrupt first") Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently flush_tmregs_to_thread() does not save the TM SPRs (TFHAR,
TFIAR, TEXASR) to the thread struct, unless the process is currently
inside a suspended transaction.
If the process is core dumping, and the TM SPRs have changed since the
last time the process was context switched, then we will save stale
values of the TM SPRs to the core dump.
Fix it by saving the live register state to the thread struct in that
case.
Fixes: 08e1c01d6aed ("powerpc/ptrace: Enable support for TM SPR state") Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com> Reviewed-by: Cyril Bur <cyrilbur@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For e.g. HZ=100, timer being 430 jiffies in the future, and 32 bit
unsigned int, there is an overflow on unsigned int right-hand side
of the expression which results with wrong values being returned.
Type cast the multiplier to 64bit to avoid that issue.
Fixes: 46c8f0b077a8 ("timers: Fix get_next_timer_interrupt() computation") Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nokia.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Cc: khilman@baylibre.com Cc: akpm@linux-foundation.org Link: http://lkml.kernel.org/r/a7900f04-2a21-c9fd-67be-ab334d459ee5@nokia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I encounter this when trying to stress the async page fault in L1 guest w/
L2 guests running.
Commit 9b132fbe5419 (Add rcu user eqs exception hooks for async page
fault) adds rcu_irq_enter/exit() to kvm_async_pf_task_wait() to exit cpu
idle eqs when needed, to protect the code that needs use rcu. However,
we need to call the pair even if the function calls schedule(), as seen
from the above backtrace.
This patch fixes it by informing the RCU subsystem exit/enter the irq
towards/away from idle for both n.halted and !n.halted.
Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mmu_notifier_release() callback of KVM triggers cleaning up
the stage2 page table on kvm-arm. However there could be other
notifier callbacks in parallel with the mmu_notifier_release(),
which could cause the call backs ending up in an empty stage2
page table. Make sure we check it for all the notifier callbacks.
Fixes: commit 293f29363 ("kvm-arm: Unmap shadow pagetables properly") Reported-by: Alex Graf <agraf@suse.de> Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Multiple frontend dailinks may be connected to a backend
dailink at the same time. When one of frontend dailinks is
closed, the associated backend dailink should not be closed
if it is connected to other active frontend dailinks. Change
ensures that backend dailink is closed only after all
connected frontend dailinks are closed.
Signed-off-by: Gopikrishnaiah Anandan <agopik@codeaurora.org> Signed-off-by: Banajit Goswami <bgoswami@codeaurora.org> Signed-off-by: Patrick Lai <plai@codeaurora.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f1013cdeeeb9 ("ASoC: ux500: drop platform DAI
assignments"), which seems to have been based on a misunderstanding and
prevents the platform driver callbacks from being made (e.g. to
preallocate DMA memory).
The real culprit for the warnings about attempts to create duplicate
procfs entries was commit 99b04f4c4051 ("ASoC: add Component level
pcm_new/pcm_free" that broke PCM creation on systems that use more than
one platform component.
Fixes: f1013cdeeeb9 ("ASoC: ux500: drop platform DAI assignments") Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 99b04f4c4051 ("ASoC: add Component level
pcm_new/pcm_free"), which started calling the pcm_new callback for every
component in a *card* when creating a new pcm, something which does not
seem to make any sense.
This specifically led to memory leaks in systems with more than one
platform component and where DMA memory is allocated in the
platform-driver callback. For example, when both mcasp devices are being
used on an am335x board, DMA memory would be allocated twice for every
DAI link during probe.
When CONFIG_SND_VERBOSE_PROCFS was set this fortunately also led to
warnings such as:
Since there seems to be no users of the new component callbacks, and the
current implementation introduced a regression, let's revert the
offending commit for now.
Fixes: 99b04f4c4051 ("ASoC: add Component level pcm_new/pcm_free") Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As I was staring at the si_init_golden_registers code, I noticed that
the Pitcairn initialization silently falls through the Cape Verde
initialization, and the Oland initialization falls through the Hainan
initialization. However there is no comment stating that this is
intentional, and the radeon driver doesn't have any such fallthrough,
so I suspect this is not supposed to happen.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Fixes: 62a37553414a ("drm/amdgpu: add si implementation v10") Cc: Ken Wang <Qingqing.Wang@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: "Marek Olšák" <maraeo@gmail.com> Cc: "Christian König" <christian.koenig@amd.com> Cc: Flora Cui <Flora.Cui@amd.com> Reviewed-by: Marek Olšák <marek.olsak@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0'). However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.
Fix the problem by moving posix_acl_update_mode() out of ocfs2_set_acl()
into ocfs2_iop_set_acl(). That way the function will not be called when
inheriting ACLs which is what we want as it prevents SGID bit clearing
and the mode has been properly set by posix_acl_create() anyway. Also
posix_acl_chmod() that is calling ocfs2_set_acl() takes care of updating
mode itself.
Fixes: 073931017b4 ("posix_acl: Clear SGID bit when setting file permissions") Link: http://lkml.kernel.org/r/20170801141252.19675-3-jack@suse.cz Signed-off-by: Jan Kara <jack@suse.cz> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In codepaths that use the begin/retry interface for reading
mems_allowed_seq with irqs disabled, there exists a race condition that
stalls the patch process after only modifying a subset of the
static_branch call sites.
This problem manifested itself as a deadlock in the slub allocator,
inside get_any_partial. The loop reads mems_allowed_seq value (via
read_mems_allowed_begin), performs the defrag operation, and then
verifies the consistency of mem_allowed via the read_mems_allowed_retry
and the cookie returned by xxx_begin.
The issue here is that both begin and retry first check if cpusets are
enabled via cpusets_enabled() static branch. This branch can be
rewritted dynamically (via cpuset_inc) if a new cpuset is created. The
x86 jump label code fully synchronizes across all CPUs for every entry
it rewrites. If it rewrites only one of the callsites (specifically the
one in read_mems_allowed_retry) and then waits for the
smp_call_function(do_sync_core) to complete while a CPU is inside the
begin/retry section with IRQs off and the mems_allowed value is changed,
we can hang.
This is because begin() will always return 0 (since it wasn't patched
yet) while retry() will test the 0 against the actual value of the seq
counter.
The fix is to use two different static keys: one for begin
(pre_enable_key) and one for retry (enable_key). In cpuset_inc(), we
first bump the pre_enable key to ensure that cpuset_mems_allowed_begin()
always return a valid seqcount if are enabling cpusets. Similarly, when
disabling cpusets via cpuset_dec(), we first ensure that callers of
cpuset_mems_allowed_retry() will start ignoring the seqcount value
before we let cpuset_mems_allowed_begin() return 0.
The relevant stack traces of the two stuck threads:
There may still be threads waiting on event_wqh at the time the
userfault file descriptor is closed. Flush the events wait-queue to
prevent waiting threads from hanging.
Link: http://lkml.kernel.org/r/1501398127-30419-1-git-send-email-rppt@linux.vnet.ibm.com Fixes: 9cd75c3cd4c3d ("userfaultfd: non-cooperative: add ability to report
non-PF events from uffd descriptor") Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: Pavel Emelyanov <xemul@virtuozzo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the non-cooperative userfaultfd case, the process exit may race with
outstanding mcopy_atomic called by the uffd monitor. Returning -ENOSPC
instead of -EINVAL when mm is already gone will allow uffd monitor to
distinguish this case from other error conditions.
Unfortunately I overlooked userfaultfd_zeropage when updating
userfaultd_copy().
Link: http://lkml.kernel.org/r/1501136819-21857-1-git-send-email-rppt@linux.vnet.ibm.com Fixes: 96333187ab162 ("userfaultfd_copy: return -ENOSPC in case mm has gone") Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: Pavel Emelyanov <xemul@virtuozzo.com> Cc: Michal Hocko <mhocko@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When mremap is called with MREMAP_FIXED it unmaps memory at the
destination address without notifying userfaultfd monitor.
If the destination were registered with userfaultfd, the monitor has no
way to distinguish between the old and new ranges and to properly relate
the page faults that would occur in the destination region.
Fixes: 897ab3e0c49e ("userfaultfd: non-cooperative: add event for memory unmaps") Link: http://lkml.kernel.org/r/1500276876-3350-1-git-send-email-rppt@linux.vnet.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Acked-by: Pavel Emelyanov <xemul@virtuozzo.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9a291a7c9428 ("mm/hugetlb: report -EHWPOISON not -EFAULT when
FOLL_HWPOISON is specified") causes __get_user_pages to ignore certain
errors from follow_hugetlb_page. After such error, __get_user_pages
subsequently calls faultin_page on the same VMA and start address that
follow_hugetlb_page failed on instead of returning the error immediately
as it should.
In follow_hugetlb_page, when hugetlb_fault returns a value covered under
VM_FAULT_ERROR, follow_hugetlb_page returns it without setting nr_pages
to 0 as __get_user_pages expects in this case, which causes the
following to happen in __get_user_pages: the "while (nr_pages)" check
succeeds, we skip the "if (!vma..." check because we got a VMA the last
time around, we find no page with follow_page_mask, and we call
faultin_page, which calls hugetlb_fault for the second time.
This issue also slightly changes how __get_user_pages works. Before, it
only returned error if it had made no progress (i = 0). But now,
follow_hugetlb_page can clobber "i" with an error code since its new
return path doesn't check for progress. So if "i" is nonzero before a
failing call to follow_hugetlb_page, that indication of progress is lost
and __get_user_pages can return error even if some pages were
successfully pinned.
To fix this, change follow_hugetlb_page so that it updates nr_pages,
allowing __get_user_pages to fail immediately and restoring the "error
only if no progress" behavior to __get_user_pages.
Tested that __get_user_pages returns when expected on error from
hugetlb_fault in follow_hugetlb_page.
Fixes: 9a291a7c9428 ("mm/hugetlb: report -EHWPOISON not -EFAULT when FOLL_HWPOISON is specified") Link: http://lkml.kernel.org/r/1500406795-58462-1-git-send-email-daniel.m.jordan@oracle.com Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com> Acked-by: Punit Agrawal <punit.agrawal@arm.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com> Cc: James Morse <james.morse@arm.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: zhong jiang <zhongjiang@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nadav Amit identified a theoritical race between page reclaim and
mprotect due to TLB flushes being batched outside of the PTL being held.
He described the race as follows:
CPU0 CPU1
---- ----
user accesses memory using RW PTE
[PTE now cached in TLB]
try_to_unmap_one()
==> ptep_get_and_clear()
==> set_tlb_ubc_flush_pending()
mprotect(addr, PROT_READ)
==> change_pte_range()
==> [ PTE non-present - no flush ]
user writes using cached RW PTE
...
try_to_unmap_flush()
The same type of race exists for reads when protecting for PROT_NONE and
also exists for operations that can leave an old TLB entry behind such
as munmap, mremap and madvise.
For some operations like mprotect, it's not necessarily a data integrity
issue but it is a correctness issue as there is a window where an
mprotect that limits access still allows access. For munmap, it's
potentially a data integrity issue although the race is massive as an
munmap, mmap and return to userspace must all complete between the
window when reclaim drops the PTL and flushes the TLB. However, it's
theoritically possible so handle this issue by flushing the mm if
reclaim is potentially currently batching TLB flushes.
Other instances where a flush is required for a present pte should be ok
as either the page lock is held preventing parallel reclaim or a page
reference count is elevated preventing a parallel free leading to
corruption. In the case of page_mkclean there isn't an obvious path
that userspace could take advantage of without using the operations that
are guarded by this patch. Other users such as gup as a race with
reclaim looks just at PTEs. huge page variants should be ok as they
don't race with reclaim. mincore only looks at PTEs. userfault also
should be ok as if a parallel reclaim takes place, it will either fault
the page back in or read some of the data before the flush occurs
triggering a fault.
Note that a variant of this patch was acked by Andy Lutomirski but this
was for the x86 parts on top of his PCID work which didn't make the 4.13
merge window as expected. His ack is dropped from this version and
there will be a follow-on patch on top of PCID that will include his
ack.
When the device is non removable, the card detect signal is often used
for another purpose i.e. muxed to another SoC peripheral or used as a
GPIO. It could lead to wrong behaviors depending the default value of
this signal if not muxed to the SDHCI controller.
Fixes: bb5f8ea4d514 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC") Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The verifier is allocated on the stack, but the EXCHANGE_ID RPC call was
changed to be asynchronous by commit 8d89bd70bc939. If we interrrupt
the call to rpc_wait_for_completion_task(), we can therefore end up
transmitting random stack contents in lieu of the verifier.
Due to a bugfix in wireless tree and the commit mentioned below a merge
was needed which went haywire. So the submitted change resulted in the
function brcmf_sdiod_sgtable_alloc() being called twice during the probe
thus leaking the memory of the first call.
Fixes: 4d7928959832 ("brcmfmac: switch to new platform data") Reported-by: Stefan Wahren <stefan.wahren@i2se.com> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iwlagn_check_ratid_empty takes the tid as a parameter, but
it doesn't check that it is not IWL_TID_NON_QOS.
Since IWL_TID_NON_QOS = 8 and iwl_priv::tid_data is an array
with 8 entries, accessing iwl_priv::tid_data[IWL_TID_NON_QOS]
is a bad idea.
This happened in iwlagn_rx_reply_tx. Since
iwlagn_check_ratid_empty is relevant only to check whether
we can open A-MPDU, this flow is irrelevant if tid is
IWL_TID_NON_QOS. Call iwlagn_check_ratid_empty only inside
the
if (tid != IWL_TID_NON_QOS)
The combination of WQ_UNBOUND and max_active == 1 used to imply
ordered execution. After NUMA affinity 4c16bd327c74 ("workqueue:
implement NUMA affinity for unbound workqueues"), this is no longer
true due to per-node worker pools.
While the right way to create an ordered workqueue is
alloc_ordered_workqueue(), the documentation has been misleading for a
long time and people do use WQ_UNBOUND and max_active == 1 for ordered
workqueues which can lead to subtle bugs which are very difficult to
trigger.
It's unlikely that we'd see noticeable performance impact by enforcing
ordering on WQ_UNBOUND / max_active == 1 workqueues. Let's
automatically set __WQ_ORDERED for those workqueues.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Christoph Hellwig <hch@infradead.org> Reported-by: Alexei Potashnik <alexei@purestorage.com> Fixes: 4c16bd327c74 ("workqueue: implement NUMA affinity for unbound workqueues") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My static checker complains that "devno" can be negative, meaning that
we read before the start of the loop. I've looked at the code, and I
think the warning is right. This come from /proc so it's root only or
it would be quite a quite a serious bug. The call tree looks like this:
proc_scsi_write() <- gets id and channel from simple_strtoul()
-> scsi_add_single_device() <- calls shost->transportt->user_scan()
-> ata_scsi_user_scan()
-> ata_find_dev()
While refactoring, f7b2814bb9b6 ("cgroup: factor out
cgroup_{apply|finalize}_control() from
cgroup_subtree_control_write()") broke error return value from the
function. The return value from the last operation is always
overridden to zero. Fix it.
On subsystem registration, css_populate_dir() is not called on the new
root css, so the interface files for the subsystem on cgrp_dfl_root
aren't created on registration. This is a residue from the days when
cgrp_dfl_root was used only as the parking spot for unused subsystems,
which no longer is true as it's used as the root for cgroup2.
This is often fine as later operations tend to create them as a part
of mount (cgroup1) or subtree_control operations (cgroup2); however,
it's not difficult to mount cgroup2 with the controller interface
files missing as Waiman found out.
Fix it by invoking css_populate_dir() on the root css on subsys
registration.
Subsystem migration methods shouldn't be called for empty migrations.
cgroup_migrate_execute() implements this guarantee by bailing early if
there are no source css_sets. This used to be correct before a79a908fd2b0 ("cgroup: introduce cgroup namespaces"), but no longer
since the commit because css_sets can stay pinned without tasks in
them.
This caused cgroup_migrate_execute() call into cpuset migration
methods with an empty cgroup_taskset. cpuset migration methods
correctly assume that cgroup_taskset_first() never returns NULL;
however, due to the bug, it can, leading to the following oops.
This patch fixes the bug by adding an explicit nr_tasks counter to
cgroup_taskset and skipping calling the migration methods if the
counter is zero. While at it, remove the now spurious check on no
source css_sets.
This commit fixes this by only calling pwm_add_table() for the first
PWM controller (which is the one used for the backlight).
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1458599 Fixes: bf7696a12071 (acpi: lpss: call pwm_add_table() for BSW...) Fixes: 04434ab5120a (ACPI / LPSS: Call pwm_add_table() for Bay Trail...) Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When LPFC is built-in but NVMe is a loadable module, we fail to link the
kernel:
drivers/scsi/built-in.o: In function `lpfc_nvme_create_localport':
(.text+0x156a82): undefined reference to `nvme_fc_register_localport'
drivers/scsi/built-in.o: In function `lpfc_nvme_destroy_localport':
(.text+0x156eaa): undefined reference to `nvme_fc_unregister_remoteport'
We can avoid this either by forcing lpfc to be a module, or by disabling
NVMe support in this case. This implements the former.
Fixes: 7d7080335f8d ("scsi: lpfc: Finalize Kconfig options for nvme") Link: https://patchwork.kernel.org/patch/9636569/ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch modifies flush_cache_range() to handle non current contexts.
In as much as this occurs infrequently, the simplest approach is to
flush the entire cache when this happens.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since kernel 4.11 the thread and irq stacks on parisc randomly overflow
the default size of 16k. The reason why stack usage suddenly grew is yet
unknown.
The existing code gives an incorrect pointer value.
The buffer pointer 'buf' was of type unsigned short *, and 'count' was a
number in bytes. A cast of buf should have been used.
However, instead of casting, just change the code to use u32 pointers.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 8185e51f358a: ("mmc: tmio-mmc: add support for 32bit data port") Signed-off-by: Chris Brandt <chris.brandt@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: <stable@vger.kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
take_dentry_name_snapshot() takes a safe snapshot of dentry name;
if the name is a short one, it gets copied into caller-supplied
structure, otherwise an extra reference to external name is grabbed
(those are never modified). In either case the pointer to stable
string is stored into the same structure.
dentry must be held by the caller of take_dentry_name_snapshot(),
but may be freely dropped afterwards - the snapshot will stay
until destroyed by release_dentry_name_snapshot().
systemd by default starts watchdog on reboot and sets the timer to
ShutdownWatchdogSec=10min. Reboot handler in ipmi_watchdog than reduces
the timer to 120s which is not enough time to boot a Xen machine with
a lot of RAM. As a result the machine is rebooted the second time
during the long run of (XEN) Scrubbing Free RAM.....
Fix this by setting the timer to 120s only if it was previously
set to a low value.
The scaler allocation code depends on a non-zero default value for the
crtc scaler_id, so make sure we initialize the scaler state accordingly
even if the crtc is off. This fixes at least an initial YUV420 modeset
(added in a follow-up patchset by Shashank) when booting with the screen
off: after the initial HW readout and modeset which enables the scaler a
subsequent modeset will disable the scaler which isn't properly
allocated. This results in a funky HW state where the pipe scaler HW
registers can't be modified and the normally black screen is grey and
shifted to the right or jitters.
The problem was revealed by Shashank's YUV420 patchset and first
reported by Ville.
v2:
- In the stable tag also include versions which need backporting (Jani)
Cc: Jani Nikula <jani.nikula@intel.com> Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Chandra Konduru <chandra.konduru@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Fixes: a1b2278e4dfc ("drm/i915: skylake panel fitting using shared scalers") Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170720112820.26816-1-imre.deak@intel.com Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 5fb9dadf336f3590c799e8cbde348215dccc2aa2) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bit 30 being set causes the upper half of BAR2 to stay in physical mode,
mapped over the end of VRAM, even when the rest of the BAR has been set
to virtual mode.
We inherited our initial value from RM, but I'm not aware of any reason
we need to keep it that way.
This fixes severe GPU hang/lockup issues revealed by Wayland on F26.
Shout-out to NVIDIA for the quick response with the potential cause!
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was originally chosen to be an arbitrarily large number. However,
some user mode may actually try to set a 16Kx16K mode and run into other
issues.
Since 8Kx8K is the current texture limit for Mesa LLVM driver, we will
just use this limit for now.
Signed-off-by: Sinclair Yeh <syeh@vmware.com> Reviewed-by: Brian Paul <brianp@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code does not look correct, and the reason for it is
probably lost. Since this now generates a compiler warning,
fix it to what makes sense.
Reported-by: Arnd Bergmann <arnd@arndb.de> Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sinclair Yeh <syeh@vmware.com> Reviewed-by: Brian Paul <brianp@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After bio is submitted, we should not clone it as its bi_iter might be
invalid by driver. This is the case of behind_master_bio. In certain
situration, we could dispatch behind_master_bio immediately for the
first disk and then clone it for other disks.
bio_add_page() won't fail for resync bio, and the page index for each
bio is same, so remove it.
More importantly the 'idx' of 'struct resync_pages' is initialized in
mempool allocator function, the current way is wrong since mempool is
only responsible for allocation, we can't use that for initialization.
Suggested-by: NeilBrown <neilb@suse.com> Reported-by: NeilBrown <neilb@suse.com> Reported-and-tested-by: Patrick <dto@gmx.net> Fixes: f0250618361d(md: raid10: don't use bio's vec table to manage resync pages) Fixes: 98d30c5812c3(md: raid1: don't use bio's vec table to manage resync pages) Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the dm-integrity superblock was corrupted in such a way that the
journal_sections field was zero, the integrity target would deadlock
because it would wait forever for free space in the journal.
Detect this situation and refuse to activate the device.
When using a block size greater than 512 bytes, the dm-integrity target
allocates journal space inefficiently. It allocates one journal entry
for each 512-byte chunk of data, fills an entry for each block of data
and leaves the remaining entries unused.
This issue doesn't cause data corruption, but all the unused journal
entries degrade performance severely.
For example, with 4k blocks and an 8k bio, it would allocate 16 journal
entries but only use 2 entries. The remaining 14 entries were left
unused.
Fix this by adding the missing 'log2_sectors_per_block' shifts that are
required to have each journal entry map to a full block.
Commit f98a8bf9ee20 ("KVM: PPC: Book3S HV: Allow KVM_PPC_ALLOCATE_HTAB
ioctl() to change HPT size", 2016-12-20) changed the behaviour of
the KVM_PPC_ALLOCATE_HTAB ioctl so that it now allocates a new HPT
and new revmap array if there was a previously-allocated HPT of a
different size from the size being requested. In this case, we need
to reset the rmap arrays of the memslots, because the rmap arrays
will contain references to HPTEs which are no longer valid. Worse,
these references are also references to slots in the new revmap
array (which parallels the HPT), and the new revmap array contains
random contents, since it doesn't get zeroed on allocation.
The effect of having these stale references to slots in the revmap
array that contain random contents is that subsequent calls to
functions such as kvmppc_add_revmap_chain will crash because they
will interpret the non-zero contents of the revmap array as HPTE
indexes and thus index outside of the revmap array. This leads to
host crashes such as the following.
Note that to trigger this, it is necessary to use a recent upstream
QEMU (or other userspace that resizes the HPT at CAS time), specify
a maximum memory size substantially larger than the current memory
size, and boot a guest kernel that does not support HPT resizing.
This fixes the problem by resetting the rmap arrays when the old HPT
is freed.
Fixes: f98a8bf9ee20 ("KVM: PPC: Book3S HV: Allow KVM_PPC_ALLOCATE_HTAB ioctl() to change HPT size") Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 46a704f8409f ("KVM: PPC: Book3S HV: Preserve userspace HTM state
properly", 2017-06-15) added code to read transactional memory (TM)
registers but forgot to enable TM before doing so. The result is
that if userspace does have live values in the TM registers, a KVM_RUN
ioctl will cause a host kernel crash like this:
When authencesn is used together with digest_null a crash will
occur on the decrypt path. This is because normally we perform
a special setup to preserve the ESN, but this is skipped if there
is no authentication. However, on the post-authentication path
it always expects the preservation to be in place, thus causing
a crash when digest_null is used.
This patch fixes this by also skipping the post-processing when
there is no authentication.
Fixes: 104880a6b470 ("crypto: authencesn - Convert to new AEAD...") Reported-by: Jan Tluka <jtluka@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Broadcom SPU driver, due to missing break statement
in spu2_hash_xlate() while mapping SPU2 equivalent
SHA3-512 value, -EINVAL is chosen and hence leading to
failure of SHA3-512 algorithm. This patch fixes the same.
Fixes: 9d12ba86f818 ("crypto: brcm - Add Broadcom SPU driver") Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the cpp include flags for compiling device tree dts files
to match the changes made to the kernel build process in
commit d5d332d3f7e8 ("devicetree: Move include prefixes from arch
to separate directory").
Signed-off-by: Frank Rowand <frank.rowand@sony.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nfs4_retry_setlk() sets the task's state to TASK_INTERRUPTIBLE within the
same region protected by the wait_queue's lock after checking for a
notification from CB_NOTIFY_LOCK callback. However, after releasing that
lock, a wakeup for that task may race in before the call to
freezable_schedule_timeout_interruptible() and set TASK_WAKING, then
freezable_schedule_timeout_interruptible() will set the state back to
TASK_INTERRUPTIBLE before the task will sleep. The result is that the task
will sleep for the entire duration of the timeout.
Since we've already set TASK_INTERRUPTIBLE in the locked section, just use
freezable_schedule_timout() instead.
Fixes: a1d617d8f134 ("nfs: allow blocking locks to be awoken by lock callbacks") Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to commit ca0daa277aca ("NFS: Cache aggressively when file is open
for writing"), NFS would revalidate, or invalidate, the file size when
taking a lock. Since that commit it only invalidates the file content.
If the file size is changed on the server while wait for the lock, the
client will have an incorrect understanding of the file size and could
corrupt data. This particularly happens when writing beyond the
(supposed) end of file and can be easily be demonstrated with
posix_fallocate().
If an application opens an empty file, waits for a write lock, and then
calls posix_fallocate(), glibc will determine that the underlying
filesystem doesn't support fallocate (assuming version 4.1 or earlier)
and will write out a '0' byte at the end of each 4K page in the region
being fallocated that is after the end of the file.
NFS will (usually) detect that these writes are beyond EOF and will
expand them to cover the whole page, and then will merge the pages.
Consequently, NFS will write out large blocks of zeroes beyond where it
thought EOF was. If EOF had moved, the pre-existing part of the file
will be over-written. Locking should have protected against this,
but it doesn't.
This patch restores the use of nfs_zap_caches() which invalidated the
cached attributes. When posix_fallocate() asks for the file size, the
request will go to the server and get a correct answer.
Fixes: ca0daa277aca ("NFS: Cache aggressively when file is open for writing") Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The register for the "new timing mode" also has bit fields for setting
output and sample timing phases. According to comments in Allwinner's
BSP kernel, the default values are good enough.
Keep the default values already in the hardware when setting new timing
mode, instead of overwriting the whole register.
Fixes: 9a37e53e451e ("mmc: sunxi: Enable the new timings for the A64 MMC
controllers") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As for commit 68baf692c435 ("powerpc/pseries: Fix of_node_put()
underflow during DLPAR remove"), the call to of_node_put() must be
removed from pSeries_reconfig_remove_node().
dlpar_detach_node() and pSeries_reconfig_remove_node() both call
of_detach_node(), and thus the node should not be released in both
cases.
Some machines can't power off the machine, so disable the lockup detectors to
avoid this watchdog BUG to show up every few seconds:
watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [systemd-shutdow:1]
It's always bothered me that we only disable preemption in
copy_user_page around the call to flush_dcache_page_asm.
This patch extends this to after the copy.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Helge noticed that we flush the TLB page in flush_cache_page but not in
flush_cache_range or flush_cache_mm.
For a long time, we have had random segmentation faults building
packages on machines with PA8800/8900 processors. These machines only
support equivalent aliases. We don't see these faults on machines that
don't require strict coherency. So, it appears TLB speculation
sometimes leads to cache corruption on machines that require coherency.
This patch adds TLB flushes to flush_cache_range and flush_cache_mm when
coherency is required. We only flush the TLB in flush_cache_page when
coherency is required.
The patch also optimizes flush_cache_range. It turns out we always have
the right context to use flush_user_dcache_range_asm and
flush_user_icache_range_asm.
The patch has been tested for some time on rp3440, rp3410 and A500-44.
It's been boot tested on c8000. No random segmentation faults were
observed during testing.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add codec IDs for several recently released, pending, and historical
NVIDIA GPU audio controllers to the patch table, to allow the correct
patch functions to be selected for them.
Signed-off-by: Daniel Dadap <ddadap@nvidia.com> Reviewed-by: Andy Ritger <aritger@nvidia.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit b56fa687e02b ("ALSA: fm801: detect FM-only card earlier")
rearranged initialization calls, i.e. it makes snd_fm801_chip_init() to
be called before we register interrupt handler and set PCI bus
mastering.
Somehow it prevents FM801-AU to work properly. Thus, partially revert
initialization order changed by commit mentioned above.
When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0'). However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.
Fix the problem by moving posix_acl_update_mode() out of
__jfs_set_acl() into jfs_set_acl(). That way the function will not be
called when inheriting ACLs which is what we want as it prevents SGID
bit clearing and the mode has been properly set by posix_acl_create()
anyway.
Fixes: 073931017b49d9458aa351605b43a7e34598caef CC: jfs-discussion@lists.sourceforge.net Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: using smp_processor_id() in preemptible [00000000] code: 99-trinity/181
caller is debug_smp_processor_id+0x17/0x19
CPU: 0 PID: 181 Comm: 99-trinity Not tainted 4.12.0-01059-g2a42eb9 #1
Call Trace:
dump_stack+0x82/0xb8
check_preemption_disabled()
debug_smp_processor_id()
vtime_delta()
task_cputime()
thread_group_cputime()
thread_group_cputime_adjusted()
wait_consider_task()
do_wait()
SYSC_wait4()
do_syscall_64()
entry_SYSCALL64_slow_path()
As Frederic pointed out:
| Although those sched_clock_cpu() things seem to only matter when the
| sched_clock() is unstable. And that stability is a condition for nohz_full
| to work anyway. So probably sched_clock() alone would be enough.
This patch fixes it by replacing sched_clock_cpu() with sched_clock() to
avoid calling smp_processor_id() in a preemptible context.
Reported-by: Xiaolong Ye <xiaolong.ye@intel.com> Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1499586028-7402-1-git-send-email-wanpeng.li@hotmail.com
[ Prettified the changelog. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ff86bf0c65f1 ("alarmtimer: Rate limit periodic intervals") sets a
minimum bound on the alarm timer interval. This minimum bound shouldn't
be applied if the interval is 0. Otherwise, one-shot timers will be
converted into periodic ones.
This patch is specific to 4.11.y and 4.12.y. Older -stable trees have a
slightly different patch, and 4.13-rc2 isn't impacted due to a later
refactoring.
Fixes: ff86bf0c65f1 ("alarmtimer: Rate limit periodic intervals") Reported-by: Ben Fennema <fennema@google.com> Signed-off-by: Greg Hackmann <ghackmann@google.com> Cc: John Stultz <john.stultz@linaro.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The move of the unpark functions to the control thread moved the BUG_ON()
there as well. While it made some sense in the idle thread of the upcoming
CPU, it's bogus to crash the control thread on the already online CPU,
especially as the function has a return value and the callsite is prepared
to handle an error return.
Replace it with a WARN_ON_ONCE() and return a proper error code.
Fixes: 9cd4f1a4e7a8 ("smp/hotplug: Move unparking of percpu threads to the control CPU") Rightfully-ranted-at-by: Linux Torvalds <torvalds@linux-foundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
He analyzed correctly that a parked cpu hotplug thread of an offlined CPU
was still on the runqueue when the CPU came back online and tried to unpark
it. This causes the thread which invoked kthread_unpark() to call
wait_task_inactive() and subsequently schedule() with preemption disabled.
His proposed workaround was to "make sure" that a parked thread has
scheduled out when the CPU goes offline, so the situation cannot happen.
But that's still wrong because the root cause is not the fact that the
percpu thread is still on the runqueue and neither that preemption is
disabled, which could be simply solved by enabling preemption before
calling kthread_unpark().
The real issue is that the calling thread is the idle task of the upcoming
CPU, which is not supposed to call anything which might sleep. The moron,
who wrote that code, missed completely that kthread_unpark() might end up
in schedule().
The solution is simpler than expected. The thread which controls the
hotplug operation is waiting for the CPU to call complete() on the hotplug
state completion. So the idle task of the upcoming CPU can set its state to
CPUHP_AP_ONLINE_IDLE and invoke complete(). This in turn wakes the control
task on a different CPU, which then can safely do the unpark and kick the
now unparked hotplug thread of the upcoming CPU to complete the bringup to
the final target state.
There are still cases on these platforms where an attempt is made to
configure the CDCLK while the power domain is off, like when coming back
from a suspend. So the workaround below is still needed.
This effectively reverts commit 63ff30442519 ("drm/i915: Nuke the
VLV/CHV PFI programming power domain workaround").
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101517 Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk> Link: http://patchwork.freedesktop.org/patch/msgid/20170628210605.4994-1-krisman@collabora.co.uk Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 886015a0ad43c7fc034b23ea4614ba39162f9ddd) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OA buffer initialization involves access to HW registers to set
the OA base, head and tail. Ensure device is awake while setting
these. With this, all oa.ops are covered under RPM and forcewake
wakelock.
Commit fabef825626d ("drm/i915: Drop struct_mutex around frontbuffer
flushes") adds a dependency to ifbdev->vma when flushing the framebufer,
but the checks are only against the existence of the ifbdev->fb and not
against ifbdev->vma. This leaves a window of opportunity where we may
try to operate on the fbdev prior to it being probed (thanks to
asynchronous booting).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101534 Fixes: fabef825626d ("drm/i915: Drop struct_mutex around frontbuffer flushes") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170622160211.783-1-chris@chris-wilson.co.uk Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
(cherry picked from commit 15727ed0d944ce1dec8b9e1082dd3df29a0fdf44) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: http://lkml.kernel.org/r/1500546969-12594-1-git-send-email-chuhu@redhat.com Fixes: ccfe9e42e451 ("tracing: Make tracing_cpumask available for all instances") Signed-off-by: Chunyu Hu <chuhu@redhat.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the genpd->attach_dev or genpd->power_on fails, genpd_dev_pm_attach
may return -EPROBE_DEFER initially. However genpd_alloc_dev_data sets
the PM domain for the device unconditionally.
When subsequent attempts are made to call genpd_dev_pm_attach, it may
return -EEXISTS checking dev->pm_domain without re-attempting to call
attach_dev or power_on.
platform_drv_probe then attempts to call drv->probe as the return value
-EEXIST != -EPROBE_DEFER, which may end up in a situation where the
device is accessed without it's power domain switched on.
Fixes: f104e1e5ef57 (PM / Domains: Re-order initialization of generic_pm_domain_data) Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The parallel panel driver should continue to work without having an
endpoint linking to an panel in DT for backwards compatibility.
With the recent switch to drm_of_find_panel_or_bridge, an absent
panel results in a failure with -ENODEV error return code. To restore
the old behaviour, ignore the -ENODEV return code.
Reported-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com> Fixes: ebc944613567 ("drm: convert drivers to use drm_of_find_panel_or_bridge") Tested-by: Chris Healy <cphealy@gmail.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...by reusing the namespace id for the device-dax instance name.
Now that we have decided that there will never by more than one
device-dax instance per libnvdimm-namespace parent device [1], we can
directly reuse the namepace ids. There are some possible follow-on
cleanups, but those are saved for a later patch to simplify the -stable
backport.
When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0'). However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.
Fix the problem by moving posix_acl_update_mode() out of
__reiserfs_set_acl() into reiserfs_set_acl(). That way the function will
not be called when inheriting ACLs which is what we want as it prevents
SGID bit clearing and the mode has been properly set by
posix_acl_create() anyway.
Fixes: 073931017b49d9458aa351605b43a7e34598caef CC: reiserfs-devel@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include the OF-based modalias in the uevent sent when registering SPMI
devices, so that user space has a chance to autoload the kernel module
for the device.
Tested-by: Rob Clark <robdclark@gmail.com> Reported-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The busy percent calculated for the Knights Landing (KNL) platform
is 1024 times smaller than the correct busy value. This causes
performance to get stuck at the lowest ratio.
The scaling algorithm used for KNL is performance-based, but it still
looks at the CPU load to set the scaled busy factor to 0 when the
load is less than 1 percent. In this case, since the computed load
is 1024x smaller than it should be, the scaled busy factor will
always be 0, irrespective of CPU business.
This needs a fix similar to the turbostat one in commit b2b34dfe4d9a
(tools/power turbostat: KNL workaround for %Busy and Avg_MHz).
For this reason, add one more callback to processor-specific
callbacks to specify an MPERF multiplier represented by a number of
bit positions to shift the value of that register to the left to
copmensate for its rate difference with respect to the TSC. This
shift value is used during CPU busy calculations.
Fixes: ffb810563c (intel_pstate: Avoid getting stuck in high P-states when idle) Reported-and-tested-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This problem shows up in 4.11 when netvsc driver is removed and reloaded.
The problem is that the channel is closed during module removal and the
tasklet for processing responses is disabled. When module is reloaded
the channel is reopened but the tasklet is marked as disabled.
The fix is to re-enable tasklet at the end of close which gets it back
to the initial state.
The issue is less urgent in 4.12 since network driver now uses NAPI
and not the tasklet; and other VMBUS devices are rarely unloaded/reloaded.
Fixes: dad72a1d2844 ("vmbus: remove hv_event_tasklet_disable/enable") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nfit_init() calls nfit_mce_register() on module load. When the module
load fails the nfit mce decoder is not unregistered. The module's
memory is freed leaving the decoder chain referencing junk. This will
cause panics as future registrations will reference the free'd memory.
Unregister the nfit mce decoder on module init failure.
[v2]: register and then unregister mce handler to avoid losing mce events
[v3]: also cleanup nfit workqueue
Fixes: 6839a6d96f4e ("nfit: do an ARS scrub on hitting a latent media error") Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Len Brown <lenb@kernel.org> Cc: Vishal Verma <vishal.l.verma@intel.com> Cc: "Lee, Chun-Yi" <joeyli.kernel@gmail.com> Cc: Linda Knippers <linda.knippers@hpe.com> Cc: lszubowi@redhat.com Acked-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Prarit Bhargava <prarit@redhat.com> Reviewed-by: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reason to disable interrupts seems to be to avoid switching to a
different processor while handling per cpu data using individual loads and
stores. If we use per cpu RMV primitives we will not have to disable
interrupts.
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1705171055130.5898@east.gentwo.org Signed-off-by: Christoph Lameter <cl@linux.com> Cc: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the writeback statistics code uses a percpu counters to hold
various statistics. Furthermore we have 2 families of functions - those
which disable local irq and those which doesn't and whose names begin
with double underscore. However, they both end up calling
__add_wb_stats which in turn calls percpu_counter_add_batch which is
already irq-safe.
Exploiting this fact allows to eliminated the __wb_* functions since
they don't add any further protection than we already have.
Furthermore, refactor the wb_* function to call __add_wb_stat directly
without the irq-disabling dance. This will likely result in better
runtime of code which deals with modifying the stat counters.
While at it also document why percpu_counter_add_batch is in fact
preempt and irq-safe since at least 3 people got confused.
Link: http://lkml.kernel.org/r/1498029937-27293-1-git-send-email-nborisov@suse.com Signed-off-by: Nikolay Borisov <nborisov@suse.com> Acked-by: Tejun Heo <tj@kernel.org> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Josef Bacik <jbacik@fb.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Jeff Layton <jlayton@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, percpu_counter_add is a wrapper around __percpu_counter_add
which is preempt safe due to explicit calls to preempt_disable. Given
how __ prefix is used in percpu related interfaces, the naming
unfortunately creates the false sense that __percpu_counter_add is
less safe than percpu_counter_add. In terms of context-safety,
they're equivalent. The only difference is that the __ version takes
a batch parameter.
Make this a bit more explicit by just renaming __percpu_counter_add to
percpu_counter_add_batch.
This patch doesn't cause any functional changes.
tj: Minor updates to patch description for clarity. Cosmetic
indentation updates.
Signed-off-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Chris Mason <clm@fb.com> Cc: Josef Bacik <jbacik@fb.com> Cc: David Sterba <dsterba@suse.com> Cc: Darrick J. Wong <darrick.wong@oracle.com> Cc: Jan Kara <jack@suse.com> Cc: Jens Axboe <axboe@fb.com> Cc: linux-mm@kvack.org Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If load_balance() fails to migrate any tasks because all tasks were
affined, load_balance() removes the source CPU from consideration and
attempts to redo and balance among the new subset of CPUs.
There is a bug in this code path where the algorithm considers all active
CPUs in the system (minus the source that was just masked out). This is
not valid for two reasons: some active CPUs may not be in the current
scheduling domain and one of the active CPUs is dst_cpu. These CPUs should
not be considered, as we cannot pull load from them.
Instead of failing out of load_balance(), we may end up redoing the search
with no valid CPUs and incorrectly concluding the domain is balanced.
Additionally, if the group_imbalance flag was just set, it may also be
incorrectly unset, thus the flag will not be seen by other CPUs in future
load_balance() runs as that algorithm intends.
Fix the check by removing CPUs not in the current domain and the dst_cpu
from considertation, thus limiting the evaluation to valid remaining CPUs
from which load might be migrated.
Co-authored-by: Austin Christ <austinwc@codeaurora.org> Co-authored-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Tested-by: Tyler Baicar <tbaicar@codeaurora.org> Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Austin Christ <austinwc@codeaurora.org> Cc: Dietmar Eggemann <dietmar.eggemann@arm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Timur Tabi <timur@codeaurora.org> Link: http://lkml.kernel.org/r/1496863138-11322-2-git-send-email-jhugo@codeaurora.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the cputime source used by vtime is jiffies. When we cross
a context boundary and jiffies have changed since the last snapshot, the
pending cputime is accounted to the switching out context.
This system works ok if the ticks are not aligned across CPUs. If they
instead are aligned (ie: all fire at the same time) and the CPUs run in
userspace, the jiffies change is only observed on tick exit and therefore
the user cputime is accounted as system cputime. This is because the
CPU that maintains timekeeping fires its tick at the same time as the
others. It updates jiffies in the middle of the tick and the other CPUs
see that update on IRQ exit:
CPU 0 (timekeeper) CPU 1
------------------- -------------
jiffies = N
... run in userspace for a jiffy
tick entry tick entry (sees jiffies = N)
set jiffies = N + 1
tick exit tick exit (sees jiffies = N + 1)
account 1 jiffy as stime
Fix this with using a nanosec clock source instead of jiffies. The
cputime is then accumulated and flushed everytime the pending delta
reaches a jiffy in order to mitigate the accounting overhead.
[ fweisbec: changelog, rebase on struct vtime, field renames, add delta
on cputime readers, keep idle vtime as-is (low overhead accounting),
harmonize clock sources. ]
Suggested-by: Thomas Gleixner <tglx@linutronix.de> Reported-by: Luiz Capitulino <lcapitulino@redhat.com> Tested-by: Luiz Capitulino <lcapitulino@redhat.com> Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Rik van Riel <riel@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wanpeng Li <kernellwp@gmail.com> Link: http://lkml.kernel.org/r/1498756511-11714-6-git-send-email-fweisbec@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current "snapshot" based naming on vtime fields suggests we record
some past event but that's a low level picture of their actual purpose
which comes out blurry. The real point of these fields is to run a basic
state machine that tracks down cputime entry while switching between
contexts.
Even though it doesn't have functional consequences, setting
the task's new context state after we actually accounted the pending
vtime from the old context state makes more sense from a review
perspective.
vtime_user_exit() is the only function that doesn't follow that rule
and that can bug the reviewer for a little while until he realizes there
is no reason for this special case.
When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0'). However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.
Fix the problem by creating __hfsplus_set_posix_acl() function that does
not call posix_acl_update_mode() and use it when inheriting ACLs. That
prevents SGID bit clearing and the mode has been properly set by
posix_acl_create() anyway.
Fixes: 073931017b49d9458aa351605b43a7e34598caef Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ib_map_mr_sg() can pass an SG-list to .map_mr_sg() that is larger
than what fits into a single MR. .map_mr_sg() must not attempt to
map more SG-list elements than what fits into a single MR.
Hence make sure that mlx5_ib_sg_to_klms() does not write outside
the MR klms[] array.
Fixes: b005d3164713 ("mlx5: Add arbitrary sg list support") Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Cc: Sagi Grimberg <sagi@grimberg.me> Cc: Leon Romanovsky <leonro@mellanox.com> Cc: Israel Rukshin <israelr@mellanox.com> Acked-by: Leon Romanovsky <leonro@mellanox.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9a148a96fc3a ("drm/i915/debugfs: add dp mst info") adds support
for DP-MST to intel_connector_info, but forgot to remove the early
return for DP-MST.
Currently we may process up/down message transactions containing
uninitialized data. This can happen if there was an error during the
reception of any message in the transaction, but we happened to receive
the last message correctly with the end-of-message flag set.
To avoid this abort the reception of the transaction when the first
error is detected, rejecting any messages until a message with the
start-of-message flag is received (which will start a new transaction).
This is also what the DP 1.4 spec 2.11.8.2 calls for in this case.
In addtion this also prevents receiving bogus transactions without the
first message with the the start-of-message flag set.
v2:
- unchanged
v3:
- git add the part that actually skips messages after an error in
drm_dp_sideband_msg_build()
Cc: Dave Airlie <airlied@redhat.com> Cc: Lyude <lyude@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Lyude <lyude@redhat.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20170719134632.13366-1-imre.deak@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
